Embed Size (px)
Citation preview
assembly instructions
Caesar 3double
#petslovesavic
A 1 plastic bottom trayB 1 plastic tray with openingC 2 lower side panelsD 1 lower back panelE 1 lower front panel with doorF 1 upper roof panelG 1 upper front panel with doorH 1 upper back panelI 1 hay rackJ 1 upper feeding and drinking side panel
K 1 upper hay rack side panelL 1 platformM 4 vertical profilesN 1 wooden ladderO 8 corner piecesP 1 feeding bowlQ 2 closing clips upper cageR 2 closing clips lower cageS 1 drinking bottle with holder
Check listBefore you start assembling your cage, please check if you have all the components. If any part is missing or damaged, do not use your cage.
instruction video
A B
C D E
M
L
K
J
N IH G F
P
O
Q
R
S
Attach on all profiles (m) 4 corner pieces (o).
1
ATTENTIONTo avoid leakage, always fill bottle 100%.Om lekken te vermijden, vul de fles altijd 100%.Afin d’éviter des fuites, toujours remplir la bouteille 100%.Um Tropfen zu vermeiden, Tränke immer 100% füllen.Para evitar gotas, siempre llenar la botella 100%.
Rince spout with hot water before first use.Voor eerste gebruik, buisje reinigen met warm water.Avant premier usage, rincer la pipette à l’eau chaude.Vor erster Verwendung, Röhrchen spülen mit heissem Wasser.Antes de usarlo, limpiar el tubito con agua caliente.
M
O
4
5A
Place the lower back panel vertical on the tray. Slide the side panels with their profiles into the profiles of the back panels. Make sure that all panels fit well into the corner pieces.
6A
Slide the lower front panel (e) into the grooves of the profiles and make sure the door is facing outwards. Fix the remaining 4 corner pieces (o) on all 4 corners.
2A
Slide the lower back panel (d) into 2 profiles. Make sure the vertical wires of the back panel are facing outwards.
3A
Slide the 2 lower side panels (c) into the profiles. Again, make sure the vertical wires are facing outwards.
Attach the 2 lower closing clips (r) on the thick horizontal wire of the side panels.
7
2B
D
CC
3C
E
O
5A
6B
7B
R
Attach the roof panel (f ) on the back panel.
10
11A
Close the roof panel. Install the hay rack (i)in the side panel. Your upper cage has now been fully assembled.
12A
Place the plastic tray with opening (b) in the lower cage part. Install the wooden ladder (n) and place the platform (l) in the corner of the tray.
8A
Now we install the upper cage. Take the front panel (g) and let it click into the feeding panel (j). Make sure the door is facing outwards.
9A
Repeat this procedure for the back panel (h). Attach the other side panel (k).
Put the upper cage part on the plastic tray and fix the 2 closing clips (q) on the plastic side panels.
13
8B
J
G
CLICK
9B
H
K
F
PULL
11B
B
12BL
N
Q
Finally, install the drinking bottle (s) and the feeding bowl (p) and your cage is now ready for use.
For US customers
Thank you for purchasing our Caesar 3 double cage.This deluxe cage was designed and made in Belgium and sold through Lixit Corporation in Napa, CAIf you have any questions or need help please contact us at: E-mail: [email protected]: 800-358-8254 Option 1 Office hours: Monday -Friday 9-4 pst
P
S
www.savic.beRinglaan 10 • B-8501 Heule • BelgiumTel. +32 56 35 33 45 • Fax +32 56 35 77 [email protected] Doc.nr.: 931231
