léÉê~íáåÖ=fåëíêìÅíáçåë=td.sirona.com/pdf/5942896_115392.pdf · Operating Instructions C8+, ... 9.8 Satelec Mini L.E.D. curing light ... Keep documents safe Always

båÖäáëÜ

`UHI=`UH=qìêå

léÉê~íáåÖ=fåëíêìÅíáçåë=

Sirona Dental Systems GmbH Table of contentsOperating Instructions C8+, C8+ Turn

båÖäáëÜ

cêÉåÅÜ

båÖäáëÜ

pé~å

áëÜ

Table of contents

1 Notes on these operating instructions................................................................. 61.1 General information on the Operating Instructions .................................................................... 6

1.2 Explanation of the symbols used ............................................................................................... 7

2 Warning and safety information ........................................................................... 102.1 General safety information......................................................................................................... 10

3 Maintenance............................................................................................................ 203.1 Care and cleaning instructions for the practice team................................................................. 203.2 Inspection and maintenance...................................................................................................... 20

3.3 Safety checks ............................................................................................................................ 21

4 Unit description ...................................................................................................... 224.1 Standards/approvals.................................................................................................................. 22

4.2 Technical data ........................................................................................................................... 23

5 System versions..................................................................................................... 24

6 Putting the system into operation ........................................................................ 286.1 System ON/OFF switch ............................................................................................................. 28

7 Patient chair............................................................................................................ 297.1 Patient positioning ..................................................................................................................... 29

7.2 Adjusting the armrest................................................................................................................. 307.3 Flat headrest/articulated headrest ............................................................................................. 30

7.4 MultiMotion headrest ................................................................................................................. 31

7.5 Changing the patient position by turning (C8+ Turn only).......................................................... 347.6 Chair programs – factory settings.............................................................................................. 35

7.7 Chair programs – reprogramming.............................................................................................. 36

7.8 Foot switch – reprogramming .................................................................................................... 377.9 Emergency stop function for chair movement ........................................................................... 38

7.10 Patient chair, options ................................................................................................................. 39

8 Dentist element....................................................................................................... 408.1 Locking the dentist element ....................................................................................................... 40

8.2 Adjusting the instrument position............................................................................................... 418.3 Swivel arm ................................................................................................................................. 41

8.4 Dentist element C8+ Cart........................................................................................................... 42

8.5 Starting an instrument................................................................................................................ 438.6 Adjusting the driving air pressure .............................................................................................. 44

8.7 Instrument spray ON/OFF – chip blower ................................................................................... 45

8.8 Instruments – adjusting the spray intensity................................................................................ 46

59 42 896 D3417D3417.201.01.22.02 3

Table of contents Sirona Dental Systems GmbHOperating Instructions C8+, C8+ Turn

9 Dentist element options......................................................................................... 479.1 Negatoscope ............................................................................................................................. 479.2 Tumbler holder .......................................................................................................................... 47

9.3 Silicone handles, right/left ......................................................................................................... 48

9.4 Tray ........................................................................................................................................... 489.5 Silicone mat............................................................................................................................... 48

9.6 3-way SPRAYVIT syringe ......................................................................................................... 49

9.7 3-way syringe ............................................................................................................................ 509.8 Satelec Mini L.E.D. curing light ................................................................................................. 51

9.9 SL or BL ISO C electric motor................................................................................................... 53

9.10 SIROSONIC L scaler ................................................................................................................ 569.11 SIROSONIC L endodontic scaler.............................................................................................. 57

9.12 Rinsing the water lines .............................................................................................................. 58

10 Assistant element................................................................................................... 6010.1 Suction handpiece/saliva ejector .............................................................................................. 60

11 Assistant element - options .................................................................................. 6111.1 3-way syringes .......................................................................................................................... 61

11.2 Microswitch for vacuum system control .................................................................................... 6111.3 Air jet pump............................................................................................................................... 61

11.4 Satelec Mini L.E.D. curing light ................................................................................................. 62

12 Water unit................................................................................................................ 6312.1 Cuspidor flushing time - factory settings ................................................................................... 63

12.2 Cuspidor flushing time - reprogramming ................................................................................... 64

12.3 Tumbler filling - factory settings ................................................................................................ 6512.4 Tumbler filling - reprogramming ................................................................................................ 65

12.5 Combination of rinsing position S

with tumbler filling and flushing controlled by dentist element .................................................. 6612.6 Assistant element control panel - cuspidor flushing .................................................................. 68

12.7 Assistant element control panel - cuspidor flushing - reprogramming ...................................... 68

12.8 Assistant element control panel - tumbler filling........................................................................ 6912.9 Assistant element control panel -

combination of mouth rinsing position S with tumbler filling and cuspidor flushing................... 70

12.10 Fresh water bottle ..................................................................................................................... 7112.11 Switching between tap water/fresh water C8+ .......................................................................... 72

12.12 Hydrocolloid connection ............................................................................................................ 73

12.13 Dürr wet suction system............................................................................................................ 7412.14 Amalgam separator................................................................................................................... 75

12.15 Disinfection system ................................................................................................................... 76

12.16 Conversion of water unit right-handed left-handed version.................................................. 77

13 Operating light - option.......................................................................................... 8013.1 SIROLUX E............................................................................................................................... 8013.2 SIROLUX FANTASTIC ............................................................................................................. 82

13.3 LEDview.................................................................................................................................... 83

59 42 896 D34174 D3417.201.01.22.02

Sirona Dental Systems GmbH Table of contentsOperating Instructions C8+, C8+ Turn

båÖäáëÜ

cêÉåÅÜ

båÖäáëÜ

pé~å

áëÜ

14 Care and cleaning instructions for the practice team ........................................ 8414.1 Care, cleaning agents, and disinfectants................................................................................... 8414.2 Patient chair............................................................................................................................... 85

14.3 Dentist element.......................................................................................................................... 88

14.4 Assistant element ...................................................................................................................... 9114.5 Water unit .................................................................................................................................. 92

14.6 Sanitation of the treatment center.............................................................................................. 98

14.7 SIROLUX E operating light ........................................................................................................ 10414.8 SIROLUX FANTASTIC operating light ...................................................................................... 106

14.9 LEDview..................................................................................................................................... 107

15 Options.................................................................................................................... 10815.1 Working stool CARL .................................................................................................................. 108

15.2 PAUL working stool (not available in the Federal Republic of Germany) .................................. 10815.3 HUGO working stool .................................................................................................................. 108

59 42 896 D3417D3417.201.01.22.02 5

1 Notes on these operating instructions Sirona Dental Systems GmbH1.1 General information on the Operating Instructions Operating Instructions C8+, C8+ Turn

1 Notes on these operating instructions

1.1 General information on the Operating Instructions

Observe the Operating Instructions Please familiarize yourself with the unit by reading through these Operat-ing Instructions before putting it into operation. It is essential that you comply with the specified warning and safety information.

Keep documents safe Always keep the Operating Instructions handy in case you or another user require(s) information at a later point in time. Save the Operating Instructions on the PC or print them out.

If you sell the unit, make sure that the Operating Instructions are included with it either as a hard copy or on an electronic storage device so that the new owner can familiarize himself with its functions and the specified warning and safety information.

Online portal for technical documents We have set up an online portal for Technical Documents at http://www.sirona.com/manuals. From here, you can download these Operating Instructions along with other documents. Please complete the online form if you would like a hard copy of a particular document. We will then be happy to send you a printed copy free of charge.

Help If you reach an impasse despite having thoroughly studied the Operating Instructions, please contact your dental depot.

59 42 896 D34176 D3417.201.01.22.02

Sirona Dental Systems GmbH 1 Notes on these operating instructions Operating Instructions C8+, C8+ Turn 1.2 Explanation of the symbols used

båÖäáëÜ

1.2 Explanation of the symbols used

Symbol Explanation Symbol Explanation

ON Patient chair up

OFF Patient chair down

CAUTION Patient chair upright

Fuse Patient chair inclined

Clean with water Factory settings

Warning of danger Activate chair program S, rinsing position(Last memory function)

Emergency stop function Activate chair program 0, entry/exit position

Wrong Activate chair program 1, upper jaw treatment position

no/not OK Activate chair program 2, lower jaw treatment position

Right Individual programming, rinsing position S

Maximum load Individual programming, entry/exit position 0

Wrong Individual programming, upper jaw treatment 1

Individual programming, lower jaw treatment 2

T 10A H

59 42 896 D3417D3417.201.01.22.02 7

1 Notes on these operating instructions Sirona Dental Systems GmbH1.2 Explanation of the symbols used Operating Instructions C8+, C8+ Turn


Short acoustic signal Can be sterilized in the autoclave at 134°C/274°F

Long acoustic signal Can be thermodisinfected in the thermodisinfector at 93°C/200°F

Time in seconds 3-way syringe – water

Time in minutes 3-way syringe – air

Stop chair movement 3-way syringe – spray

Brake applied Can be set only by the service engineer

Brake released Tumbler filler

Speed increase Cuspidor flushing

Speed reduction Press and hold key

Observe operating instructions of the manufacturer

Release key

Spray cooling Press key briefly

Changing the intensity of spray air/spray water

LEDview/SIROLUX E/SIROLUX FANTASTIC

Maximum brightness

Increase/reduction of a variable LEDview/SIROLUX E/SIROLUX FANTASTIC

Reduced brightness

2743 min

93°C

200°F

>10s

<10m

8 +

1

2040

60

80

ENDO

1

2040

60

80

ENDO

1

2040

60

80

ENDO

+ / –

59 42 896 D34178 D3417.201.01.22.02

Sirona Dental Systems GmbH 1 Notes on these operating instructions Operating Instructions C8+, C8+ Turn 1.2 Explanation of the symbols used

båÖäáëÜ
Heat dissipation or

Approximately Amalgam recycling

Tap water CW rotation of electric micromo-tor

After consulting hours CCW rotation of electric micro-motor

Reprogramming

59 42 896 D3417D3417.201.01.22.02 9

2 Warning and safety information Sirona Dental Systems GmbH2.1 General safety information Operating Instructions C8+, C8+ Turn

2 Warning and safety information

2.1 General safety information

Identification of warning and safety information

To prevent any personal injury or material damage, please observe the warnings and safety instructions provided in the present operating instruc-tions. All such information is highlighted by the signal words NOTE, CAU-TION or WARNING.

Information on the unit Accompanying documents

This icon can be found next to the rating plate on the unit.

Meaning: Observe the Operating Instructions when operating the unit.

This icon can be found on the rating plate on the unit.

Meaning: The accompanying documents are available on the Sirona homepage.

Intended use This dental treatment center is designed to be used in the field of dentistry and must only be operated by qualified dental personnel.

Contraindications for the use of the treatment center, if any, are listed in the individual sections, e.g. Treatment instruments.

This unit is not intended for operation in areas subject to explosion hazards.

This unit is permanently installed. Operation is not permitted in mobile vehi-cles.

Intended use also includes compliance with these Operating Instructions and the relevant maintenance instructions.

On-site installation The on-site installation must have been performed according to our require-ments. The details are described in the document "Installation Require-ments".

Installing the treatment center Installation must be carried out by authorized technicians in accordance with the installation instructions.

Media quality The air and water supplies must meet the requirements specified in the installation requirements.

As the owner of the treatment center, you are generally responsible for the water quality.

The colony count must fulfill the national regulations for drinking water and must not exceed 500 CFU/ml under any circumstances (CFU: colony forming unit).

In the event of an increased colony count, the indoor installation must be checked and the cause of contamination eliminated. Alternatively, a stand-alone water supply can also be installed. In addition, the optional fresh water vessel can be used.

Before installation of the treatment center, an acceptable microbiological water quality for the domestic water supply must be ensured and docu-mented in the form of a colony count. Sampling and the colony count must be performed by a competent laboratory.

59 42 896 D341710 D3417.201.01.22.02

Sirona Dental Systems GmbH 2 Warning and safety information Operating Instructions C8+, C8+ Turn 2.1 General safety information

båÖäáëÜ

Check the quality of the water from the treatment center at regular intervals and after periods of disuse of over > 1 week, see "Microbiological water test" on page 97. Please contact your specialized dealer or your relevant dental association for the respective national requirements and measures.

Highly immunosuppressed patients should not come in contact with water from the treatment center. The use of sterile solutions is recommended.

Connection to the public drinking water supply

Treatment center with isolation from public drinking water supply

Provided it is equipped with a disinfection system, the treatment center fulfills the requirements of EN 1717 (free outlet with sections ≥ 20 mm and the Ger-man Gas and Water Association (DVGW). It is intrinsically safe in accor-dance with worksheet W540 and therefore also fulfills the W270 requirements as well as the requirements for plastics used in the transport of drinking water. It can be connected directly to the public drinking water sup-ply.

Provided it is equipped with a fresh water vessel without switchover to the public drinking water supply then the treatment center fulfills the require-ments of both EN 1717 and those of the German Gas and Water Association (DVGW).

The treatment center therefore also bears the symbol for the German Gas and Water Association (DVGW) along with the rating plate on the chair base.

The DVGW approval of the treatment center expires if a media block is installed in the base of the chair, see page 39 and 73.

Treatment center without isolation from public drinking water supply

If compliance with EN 1717 is stipulated nationally, appropriate equipment must be installed beyond the treatment center to protect the public drinking water system.

This applies to the following unit versions:

• without disinfection system

• with media block on the patient chair

• with a fresh water bottle (with connection to the public drinking water supply)

The treatment center then does not bear the DVGW icon.

Please always adhere to the national requirements with regard to connecting treatment centers to the public drinking water supply.

59 42 896 D3417D3417.201.01.22.02 11


Maintenance and repair Authorized technical personnel and spare parts

As manufacturers of dental medical units and in the interest of the opera-tional safety of your system, we stress the importance of having mainte-nance and repair of this unit performed only by ourselves or by agencies expressly authorized by us. Furthermore, failed components must always be replaced with original spare parts.

We suggest that you request a certificate showing the nature and extent of the work performed from those who carry out such work; it must contain any changes in rated parameters or working ranges (if applicable), as well as the date, the name of the company and a signature.

Maintenance intervals

Despite the outstanding quality of your treatment center and regular care by the practice team, preventive maintenance must be performed at scheduled intervals in the interest of operational safety.

In order to ensure the operational safety and reliability of your treatment cen-ter and to avoid damage due to natural wear, as the system owner you must have your system checked regularly by an authorized service engineer from your dental depot. Furthermore, safety checks must be performed. Please contact your dental depot to obtain a maintenance offer. For more informa-tion, please refer to section 3 "Maintenance".

Trouble-free operation Use of this unit is permissible only if it works properly without malfunctions. If trouble-free operation cannot be ensured, the unit must be taken out of ser-vice, checked by authorized technicians for malfunctions and, if necessary, repaired.

Vacuum system The suction removal of aluminum and other metal oxides from blasting devices via the amalgam separator and the automatic separator installed in the treatment center is prohibited! This would cause extreme wear and clog-ging of the suction and water paths.

A separate vacuum system must be used in connection with metal oxide blasting devices. Treatment centers equipped with a central wet suction sys-tem are generally suitable for suction removal of the above material. How-ever, make sure to observe the instructions provided by the manufacturer of your vacuum system.

No restrictions apply when using salt blasting devices in connection with Sirona treatment centers. However, in such cases, make sure that the system is subsequently flushed with an adequate amount of water.

Intermittent operation The motors of the treatment center and of the treatment instruments are designed for intermittent operation corresponding to the dental mode of treatment.

Drive motors for patient chair and backrest: max. 6% duty cycle (max. 15 s "ON"/3 min, 55 s "OFF")

Care, cleaning agents, and disinfec-tants

Unsuitable care and cleaning agents or disinfectants may corrode the sur-face of the unit or impair its functioning.

Therefore, use only care and cleaning agents and disinfectants which have been approved by Sirona. For further information, see "Care, cleaning agents, and disinfectants" on page 84.

59 42 896 D341712 D3417.201.01.22.02


båÖäáëÜ

Ventilation slots Under no circumstances may the ventilation slots on the unit be covered, since otherwise the air circulation will be obstructed. This can cause the unit to overheat.

Do not spray liquids such as disinfectants into the ventilation slots. This may lead to malfunctions. Use only wipe disinfection in these areas.

Cuspidor bowl Do not use any foaming domestic cleaning agents!

Modifications and extensions to the unit

Modifications to this unit which might affect the safety of the system owner, patients or other persons are prohibited by law.

For reasons of product safety, this product may be operated only with original Sirona accessories or third-party accessories expressly approved by Sirona. The user assumes the risk of using non-approved accessories.

If any units not approved by Sirona are connected, they must comply with the applicable standards, e.g.:

• IEC 60950 for information technology equipment (e.g. PC) and• IEC 60601-1 for medical electrical equipment.

The treatment center monitor must fulfill the requirements of the IEC 60950 standard.

The loudspeaker port of the monitor may be connected only to a unit that complies with IEC 60950 (e.g. a PC) or IEC 60601-1. Under no circum-stances may it be connected e.g. to a stereo system, etc..

If a system is created during the installation process, the requirements of IEC 60601-1, 3rd edition, must be fulfilled. The system author assumes responsi-bility for conformity of the system with the 93/42/EEC Directive.

Electromagnetic compatibility (EMC) The C8+ and C8+ Turn comply with the requirements of IEC 60601-1-2.

Medical electrical equipment is subject to special precautionary measures with regard to electromagnetic compatibility (EMC). They must be installed and operated as specified in the document "Installation Requirements".

Portable and mobile RF communications equipment may interfere with medi-cal electrical equipment. Therefore, the use of such devices (e.g. cellular phones) in practice or hospital environments must be prohibited.

Operating an RF surgical device

Treatment with HF surgical devices creates strong electromagnetic fields, which may impact other electronic devices. Do not place external RF surgical devices on the shelf space of the treatment center and do not guide the RF handpiece cable over this. Electromagnetic disturbances can often be reduced, if the external RF surgical unit is operated with a neutral electrode.

Video system

Electromagnetic disturbances in the environment of the treatment center may result in reduced image quality. In such cases, it is advisable to repeat the exposure before saving the image.

When a line drop occurs, the image data stored in the video camera may be lost. Deposit the camera and repeat the exposure.

Image artifacts may possibly occur as a result of radio-frequency interfer-ence caused by the transmitters of e.g. radio services or radio amateurs.

Influencing of cardiac pacemakers The treatment center contains strong magnets. These magnets can affect cardiac pacemakers implanted in patients, users and technical personnel.

Therefore, please observe the safety information on page 30.

59 42 896 D3417D3417.201.01.22.02 13


Dismantling / Installation When dismantling and reassembling the unit, proceed according to the installation instructions for new installation in order to guarantee its function-ing and stability.

Disposal Your product is marked with the adjacent symbol. Within the European Eco-nomic Area, this product is subject to Directive 2002/96/EC as well as the corresponding national laws. This directive requires environmentally sound recycling / disposal of the product. The product must not be disposed of as domestic refuse!

Please observe the disposal regulations applicable in your country.

Disposal procedure

Please note that this product is subject to the stipulations in EC Directive 2002/96 governing waste electrical and electronic equipment and must be disposed of in line with these special requirements within the European Union (EU).

Prior to disassembly / disposal of the product, it must be fully prepared (cleaned / disinfected / sterilized).

When disposing of equipment permanently, please proceed as follows:

In Germany:

To initiate return of the electrical device, please send a disposal order to "enretec GmbH".

1. You can find a form for placing a disposal order on the company's homep-age at www.enretec.de under the menu item "Entsorgung elektrischer und elektronischer Geräte" (Disposal of electrical and electronic devices). The form can either be downloaded or filled out online.

2. Fill out the form with the corresponding details and send it either as an on-line order or fax it to enretec GmbH at +49(0)3304 3919 590. You can also get in touch with the following contacts for disposal orders and any questions relating to this you may have: Phone: +49(0)3304 3919 500; E-mail: [email protected]: enretec GmbH, Geschäftsbereich eomRECYCLINGKanalstrasse 17, 16727 Velten

Your equipment that is not permanently installed will be collected in the prac-tice, while your permanently installed equipment will be collected curbside at your address at the agreed time and date.

All disassembly, transport and packaging costs are to be borne by the owner / operator of the equipment. The disposal itself is free of charge.

Worldwide (outside Germany):

Please contact your local dental equipment specialist for country-specific information on disposal.

59 42 896 D341714 D3417.201.01.22.02


båÖäáëÜ

Maximum load capacity of the patient chair

Please observe the patient chair's maxi-mum load capacity of 135 kg.

The weight distribution complies with ISO 6875. The mechanical stability test is performed with a multiple safety factor according to IEC 60601-1.

The maximum permissible weight of accessories mounted on the patient chair is 5 kg.

Safety stop for patient chair

• Headrest• Backrest• Toeboard

Hand / foot placement

The patient’s arms and legs must be resting on the upholstery of the chair.

CAUTIONMake sure that no obstacles (e.g. window wings, drawers, devices, …) extend into the movement range.

STOP STOP

STOP STOP

1.

2.

wrongright

59 42 896 D3417D3417.201.01.22.02 15


Safety stop for assistant element

Safety stop for cuspidor

C8+ Turn

C8+ "Long cuspidor"

Position of the dentist element

CAUTIONWhen moving the chair (via program or manually), make sure that the patient does not under any circumstances come into contact with the support arm or the dentist element.

STOP

STOP

59 42 896 D341716 D3417.201.01.22.02


båÖäáëÜ

Satelec Mini L.E.D. curing light

The curing light contains powerful LEDs. In accordance with IEC 62471, they are classified in risk group 2 with the light bar removed.

CAUTIONDo not stare into the beam path for longer periods, as this can cause eye damage.

Do not under any circumstances stare into the beam path when the light bar is re-moved.

Do not look into the light reflected by the tooth surface.

Do not observe the light aperture with op-tical instruments which can decrease the beam cross-section (e.g. magnifying lens-es).

Use the glare shield!

The light beams emitted by this instrument may be hazardous and may never be di-rected to the eyes of any person, even if this person wears goggles with protective lenses.

The light may be directed exclusively to the treatment area in the oral cavity.

Heavy line voltage drops may lead to a shutdown of the Mini L.E.D. The fault is signaled by a double beep. Check the se-lected operating mode and restart the Mini L.E.D.

ATTENTION! Potentially dangerous optical radiation!

iKbKaK=ÄÉ~ãÉñáí=~éÉêíìêÉ

right! right!wrong! wrong!

59 42 896 D3417D3417.201.01.22.02 17


Additional safety information

Any condensation occurring in the hand-piece of the Mini L.E.D. may cause impairments (e.g. fogging of the L.E.D.). When moving the handpiece from a cool environment to a warm room, always wait for it to reach room temperature before putting it into operation.

Curing lights must not be used on persons who are suffering from or have in the past been afflicted by photobiological reactions (including solar urticaria and erythropoetic porphyria). Nor should they be used on persons currently being treated with any medications which increase one’s sensi-tivity to light (including methoxsalene and chlorotetracycline).

Any persons who have in the past suf-fered from retinal or eye lens disorders or have undergone eye surgery, especially for gray cataracts, must consult their med-ical eye specialist before using the light or undergoing treatment with the Mini L.E.D. Caution is advisable even if the patient gives his or her consent, since the light intensity can cause accidents.

It is especially advisable to always wear appropriate protective goggles (UV filter).

Operation and optical specification

see chapter 9.8

59 42 896 D341718 D3417.201.01.22.02


båÖäáëÜ

SIROSONIC L

SIROLUX E/SIROLUX FANTASTIC

SIROLUX E

CAUTIONNever operate without cover:Watch out for overheating of lamp compo-nents and let them cool down.

SIROLUX FANTASTIC

CAUTIONPay attention to elevated temperature of the lamp components; and let these cool down.

Fresh water bottle

CAUTIONUse only Sirona fresh water bot-tles!

wrong! right !

right wrong

LE

MO

N

LEM

ON

wrong

59 42 896 D3417D3417.201.01.22.02 19

3 Maintenance Sirona Dental Systems GmbH3.1 Care and cleaning instructions for the practice team Operating Instructions C8+, C8+ Turn

3 Maintenance

Despite the outstanding quality of your treatment center, it is necessary to per-form inspections and preventive mainte-nance as well as safety tests at scheduled intervals in order to ensure its operational safety.

These events are documented in the Maintenance Manual.

Care and cleaning is done by the practice team.

For details please refer to the following sections.

3.1 Care and cleaning instructions for the practice team

The practice team is responsible for regu-lar cleaning and care of the treatment center, with the aim of minimizing the risk of contamination for patients and users.

The work to be performed is specified in the chapter "Care and cleaning instruc-tions for the practice team".

3.2 Inspection and maintenance

In order to ensure the operational safety and reliability of your treatment center and to avoid damage due to natural wear, annual inspection and maintenance must be performed on your treatment center. This is done by an authorized service engineer from your dental depot.

The steps to be performed as well as the parts which must be replaced are speci-fied in the document "Maintenance Cer-tificate".

An overview of the inspection and mainte-nance work performed is additionally recorded by the service engineer in the "Installation Report/Warranty Pass-port". This document is part of the "Main-tenance Manual".

59 42 896 D341720 D3417.201.01.22.02

Sirona Dental Systems GmbH 3 Maintenance Operating Instructions C8+, C8+ Turn 3.3 Safety checks

båÖäáëÜ

3.3 Safety checks

Medical equipment is designed in such a way that the first occurrence of a fault does not create a hazard to the safety of patients, users or other persons. Hence it is important to detect such faults before a second fault occurs, which might then lead to safety hazards.

For that reason it is essential to perform safety tests every 2 years which aim par-ticularly at detecting electrical faults (e.g. isolation defects). This is done by an authorized service engineer from your dental depot, most practically together with the work to be performed according to section 3.2.

The check includes a visual inspection as well as measurements of the protective ground wire connections and the equiva-lent leakage currents.

The inspections and measurements to be performed are specified in the "Mainte-nance Manual". The measured values must be documented there by the service engineer.

Safety tests must also be performed and documented during initial startup, after extensions/upgrades (conversion) of your treatment center and after repair work which might affect the electrical safety of the system.

NOTE iThe treatment center must not be operat-ed if it has failed to pass the safety tests!

59 42 896 D3417D3417.201.01.22.02 21

4 Unit description Sirona Dental Systems GmbH4.1 Standards/approvals Operating Instructions C8+, C8+ Turn

4 Unit description

4.1 Standards/approvals

The treatment center complies with the following standards:

• IEC 60601-1 (electrical, mechanical, and software safety)• IEC 60601-1-2 (electromagnetic compatibility)• IEC 60601-1-6 (serviceability)• ISO 6875 (Patient chair)• ISO 7494-1 (Dental treatment units)• ISO 7492-2 (dental treatment units, water and air supply)• ISO 9680 (Operating light)• ISO 11143 (amalgam separator), see also below (provided amalgam

separator option is available)• EN 1717 (connection to the drinking water system),

see also below (DVGW)

Original language of the present document: German

This product bears the CE mark in accordance with the provisions of the Council Directive 93/42/EEC of June 14, 1993 concerning medical devices (MDD).

The treatment center fulfills the requirements of the directive on the restric-tion of hazardous substances, 2011/65/EU.

The treatment center meets the requirements of the Canadian Standard Association (CSA) in accordance with CAN/CSA-C22.2 No. 60601-1-08.

The amalgam separator achieves a separation efficiency of > 95%. The requirements of the ISO 11143 standard are thereby fulfilled.

Separating procedure type 1: Centrifugal system

The amalgam separator is approved by the German Institute for Structural Engineering (DIBT) and by the AFNOR (France).

When equipped with a disinfection system, the treatment center complies with the technical rules and requirements on safety and hygiene for connec-tion to the public drinking water supply.

The unit is certified according to the requirements of the German Technical and Scientific Association for Gas and Water (DVGW). It is intrinsically safe in accordance with worksheet W540. The unit thus fulfills the requirements of EN 1717, see also the chapter entitled "Connection to the public drinking water supply" on page 11.

The DVGW approval of the treatment center expires if a media block is installed in the base of the chair.

This unit meets the requirements of BELGAQUA and may therefore be con-nected to the public drinking water supply in Belgium.

0123

SIRONADental Systems

GmbH64625 BensheimFabrikstrasse 31

Z-64.1-24

59 42 896 D341722 D3417.201.01.22.02

Sirona Dental Systems GmbH 4 Unit description Operating Instructions C8+, C8+ Turn 4.2 Technical data

båÖäáëÜ

4.2 Technical data

Model designation: C8+, C8+ Turn

Power connection: 100 V / 115 V / 127 V / 230 VAC 50 / 60 Hz

Rated current: 11.5 A at 100 V AC9.5 A at 115 V AC 4.5 A at 230 V AC.In addition, max. 6 A for external units see page 39

Main unit fuse: T 10 A H, 250 V AC , REF 10 77 460

Protection class: Class I device

Device class in accordance with Directive 93/42/EEC:

Class IIa device

Degree of protection against elec-trical shock:

Type B applied parts

Except SIROCAM 3 / SIROCAM C. These are:

Type BF applied parts

Degree of protection against ingress of water:

Ordinary equipment (without protection against ingress of water)

The foot switch has an IP X1 degree of protection against liquids (drip-proof).

Mode of operation Continuous operation with intermittent loading accord-ing to the type of dental operation, see page 12

This unit is permanently installed. Operation is not permitted in mobile vehicles.

Transport and storage conditions: Temperature: -40°C – +70°C -40°F – +158°F

Relative humidity: 10% – 95%Air pressure: 500hPa – 1,060hPa

Operating conditions: Ambient temperature: 10°C – 40°C 50°F – 104°F

Relative humidity: 30% – 85% (no condensa-tion)Air pressure: 700hPa – 1,060hPa

Installation location: ≤ 3,000 m above sea level

This treatment center is not suitable for operation in areas subject to explosion hazards.

Pollution degree: 2 acc. to IEC 60664-1

Year of manufacture: (on the rating plate of the patient chair)

-40

+70 1060

500

95

10

+10

+40 1060

700

85

30

59 42 896 D3417D3417.201.01.22.02 23

5 System versions Sirona Dental Systems GmbHOperating Instructions C8+, C8+ Turn

5 System versions

C8+ OTP

1. Patient chair/Patient chair Turn1

2. OTP dentist element

3. Water unit

4. Assistant element

5. Operating light

6. Instrument foot switch with program positions

7. Instrument foot switch

P1

P2

P

2

0

1

S

C8 +

12

S

P

0

100

120

4060

80

ENDO

3.4.

5.

7.

2.

1.

6.

1. Alternative equipment, not illustrated

59 42 896 D341724 D3417.201.01.22.02

Sirona Dental Systems GmbH 5 System versions Operating Instructions C8+, C8+ Turn

båÖäáëÜ

C8+ with swivel arms


2. Dentist element with swivel arms

3. Water unit


5. Operating light



C8+ Cart


2. Dentist element

3. Water unit


5. Operating light



P1

P2

P

2

0

1

S

C8 +

12

S

P

0

100

120

4060

80

ENDO

3.4.

5.

7.

2.

1.

6.

3.4.

5.

7.

2.1.

6.


59 42 896 D3417D3417.201.01.22.02 25

5 System versions Sirona Dental Systems GmbHOperating Instructions C8+, C8+ Turn

C8+ Turn

1. Patient chair Turn

2. OTP dentist element/Dentist element with swivel arms1

Cart dentist element1

3. Water unit


5. Operating light



8. Swivel arm for right-handed/left-handed conversion

C8+ without dentist element


2. Water unit


4. Operating light

NOTE iFor operation of the SIVISION 3 video system, please refer to Operating Instruc-tions 59 67 893.

P1

P2

P

2

0

1

S

C8 +

12

S

P

0

100

120

4060

80

ENDO

3.4.

5.

7.

2.

1.

6.

8.


2.3.

4.

1.


59 42 896 D341726 D3417.201.01.22.02

Sirona Dental Systems GmbH 5 System versions Operating Instructions C8+, C8+ Turn

båÖäáëÜ

Dentist element equipping options

NOTE iThe BL ISO C option is not available in all countries.

1 2 3 4 5

OptionMotor SL

oder / orou / o

Turbine

Motor SLMotor SL

SIROCONIC LSPRAYVIT

SIROCAM 3/C

Polymerisations-licht Mini L.E.D.

Turbine Turbine

oder / orou / o

oder / orou / o

oder / orou / o

oder / orou / o

OptionMotorBL ISO

oder / orou / o

Turbine SIROSONIC LSPRAYVIT

SIROCAM 3/C

Motor BL ISO Turbine

oder / orou / o

oder / orou / o


oder / orou / o


oder / orou / o


P

2

0

1

S

C8 +

12

S

P

0

100

120

4060

80

ENDO

1 2 3 4 5

Option:SL motor

Option:BL ISO C motor

SPRAYVIT Highspeed handpiece

Highspeed handpiece

Highspeed handpiece

SIROSONIC L

SL motor SL motor

SIROCAM 3/C

Mini LED curing light


SprayvitHighspeed handpiece

BL ISO C motor

Highspeed handpiece SIROSONIC L

SIROCAM 3/C



or or or or or

or

or or

or

or

59 42 896 D3417D3417.201.01.22.02 27

6 Putting the system into operation Sirona Dental Systems GmbH6.1 System ON/OFF switch Operating Instructions C8+, C8+ Turn

6 Putting the system into operation

6.1 System ON/OFF switch

12

S

P

0

100

120

4060

80

ENDO

59 42 896 D341728 D3417.201.01.22.02

Sirona Dental Systems GmbH 7 Patient chair Operating Instructions C8+, C8+ Turn 7.1 Patient positioning

båÖäáëÜ

7 Patient chair

7.1 Patient positioning

Option

Option

Option

P

2

0

1

S

C8 +

12

S

P

0

100

120

4060

80

ENDO

P

2

0

1

S

C8 +

12

S

P

0

100

120

4060

80

ENDO

S

1

0

2

P

2

0

1

S

C8 +

P

S

1

0

2

S

1

0

2P

S

1

0

2

59 42 896 D3417D3417.201.01.22.02 29

7 Patient chair Sirona Dental Systems GmbH7.2 Adjusting the armrest Operating Instructions C8+, C8+ Turn

7.2 Adjusting the armrest

A Folding armrest (option)

B Wide backrest

C Narrow backrest

CAUTIONRisk of collision!The following versions must not be retrofit-ted with an armrest:• C8+ with fixed water unit in combination with long cuspidor

7.3 Flat headrest/articulated headrest

A Flat headrest

B Articulated headrest (option)

WARNING The head pad (A) contains a strong magnet (1) on its bottom side. This magnet could affect any cardiac pace-maker located nearby.

Therefore, do not allow patients, users and technical personnel with a cardiac pacemaker to be located near this mag-net.

Furthermore, direct contact of the head pad with magnetic cards can lead to data loss.

A

BC

A

B

1

59 42 896 D341730 D3417.201.01.22.02

Sirona Dental Systems GmbH 7 Patient chair Operating Instructions C8+, C8+ Turn 7.4 MultiMotion headrest

båÖäáëÜ

7.4 MultiMotion headrest

Adjustment to patient's height

The headrest can be adjusted to the patient's height by pulling out or pushing in the headrest extension. This adjust-ment is usually required at the beginning of treatment!

NOTE iBefore positioning the patient on the headrest, make sure that the head sup-port has been optimally adjusted to the patient's height. This simplifies all subse-quent work with the MultiMotion consider-ably, since readjustment to the patient's height can thus be omitted when changing over from mandibular to maxillary treat-ment.

The MultiMotion enables you to adjust the patient's head in a way that optimally sup-ports viewing of areas of the mouth which are difficult to access.

Adjustment of hyperextension

Mandibular position

The mandibular position can be set by pulling the operating handle (A). The ana-tomical movement of the arched exten-sion keeps the patient's head in the sup-port.

Pull the headrest out of the guide by pulling handle A.

NOTE iYou can reduce the adjustment noise by pressing release A.

A

59 42 896 D3417D3417.201.01.22.02 31

7 Patient chair Sirona Dental Systems GmbH7.4 MultiMotion headrest Operating Instructions C8+, C8+ Turn

Maxillary position

Take the load off the headrest by lift-ing it slightly.

Press release A in the key recess area on the handle.

Let the headrest slide down slowly.

Let go of the release when the head-rest reaches the desired position.

Rotation and tilt

The MultiMotion enables rotation of the patient's head about the longitudinal axis of his body as well as lateral tilting of his head.

The MultiMotion is set to the desired posi-tion as follows:

1. Press and hold one or both of the two side control elements B.The rotation and tilt adjustment locks of the headrest are now released.

2. Set the headrest to the desired posi-tion.

3. Let go of the control elements B.

The supporting surface is fixed in place.

Make sure that the headrest is indeed locked in place after you let go of the control elements!

A

B B

59 42 896 D341732 D3417.201.01.22.02

Sirona Dental Systems GmbH 7 Patient chair Operating Instructions C8+, C8+ Turn 7.4 MultiMotion headrest

båÖäáëÜ

Removing the MultiMotion

For certain treatments (e.g. of children) it may be expedient to remove the MultiMo-tion completely in order to obtain better access to the patient. The patient's head will then be supported on the contact sur-face of the headrest extensionF.

To remove the MultiMotion, proceed as follows:

1. Press release button C.

2. Pull the complete headrest out of the headrest extension.

3. Cover the opening of the headrest ex-tension with cover cap E.

4. If a children's head pad D is available, place it on the headrest extension. The head pad is held magnetically.

WARNING The children's head pad (D) contains a strong magnet on its bottom side. This magnet could affect any cardiac pace-maker located nearby.Therefore, do not allow patients, users and technical personnel with a cardiac pacemaker to be located near this mag-net.

Furthermore, direct contact of the head pad with magnetic cards can lead to data loss.

NOTE iStore the removed MultiMotion in a safe place where it cannot fall onto the floor.

Inserting the MultiMotion

To insert the MultiMotion, proceed as fol-lows:

Check the guide of the removed headrest for contamination. Remove any contamination.

Remove the cover cap E.

Reinsert the MultiMotion in the guide from above until it audibly locks in place. Pull on the headrest again to make sure that it is locked securely in place.

C

ED

F

59 42 896 D3417D3417.201.01.22.02 33

7 Patient chair Sirona Dental Systems GmbH7.5 Changing the patient position by turning (C8+ Turn only) Operating Instructions C8+, C8+ Turn

7.5 Changing the patient position by turning (C8+ Turn only)

Turning the patient chair

The patient chair can be turned max. 17° to either side.

CAUTIONRisk of collision!When turning the chair, make sure that it does not collide with any other compo-nents of the treatment center, persons, furnishings or equipment. Turn the chair only if all treatment instru-ments are in place.

1. Step on foot pedal A to release the locking brake.

2. Turn the patient chair to the desired position.

3. The chair locks in place as soon as you release foot pedal A.

S

0

A

17° 17°

59 42 896 D341734 D3417.201.01.22.02

Sirona Dental Systems GmbH 7 Patient chair Operating Instructions C8+, C8+ Turn 7.6 Chair programs – factory settings

båÖäáëÜ

7.6 Chair programs – factory settings

Last Memory function

Option

Option

C8+ without dentist element: alternatively

Option

S

S 0

0

1 2

1 2

SP

P

0P

P

P

S

1

0

2

1 2

P

2

0

1

S

C8 +

12

S

P

0

100

120

4060

80

ENDO

P

2

0

1

S

C8 +

12

S

P

0

100

120

4060

80

ENDO

P1

P2

S

0

1

2

<3s <3s

1. 2. 1. 2.

<3s <3s1. 2. 1. 2.

1.S

2.S

S

P

2

0

1

S

C8 +

P

S

1

0

2

P1

P2

59 42 896 D3417D3417.201.01.22.02 35

7 Patient chair Sirona Dental Systems GmbH7.7 Chair programs – reprogramming Operating Instructions C8+, C8+ Turn

7.7 Chair programs – reprogramming

Option

Option

C8+ without dentist element: alternatively

P

2

0

1

S

C8 +

12

S

P

0

100

120

4060

80

ENDO

P

2

0

1

S

C8 +

12

S

P

0

10

120

4060

80

ENDO

P

S

1

0

2

12

S

P

0

100

120

4060

80

ENDO

12

S

P

0

100

120

4060

80

ENDO

P

S

1

0

2 P

2

0

1

S

C8 +

12

S

P

0

100

120

4060

80

ENDO

S 0 1 2

S 0 1 2

S 0 1 2

>3s

P

2

0

1

S

C8 +

P

S

1

0

2

59 42 896 D341736 D3417.201.01.22.02

Sirona Dental Systems GmbH 7 Patient chair Operating Instructions C8+, C8+ Turn 7.8 Foot switch – reprogramming

båÖäáëÜ

7.8 Foot switch – reprogramming

Option

>3s

P1

P2

59 42 896 D3417D3417.201.01.22.02 37

7 Patient chair Sirona Dental Systems GmbH7.9 Emergency stop function for chair movement Operating Instructions C8+, C8+ Turn

7.9 Emergency stop function for chair movement

Option

Option

Option

alternatively

P

2

0

1

S

C8 +

P

S

1

0

2

or

59 42 896 D341738 D3417.201.01.22.02

Sirona Dental Systems GmbH 7 Patient chair Operating Instructions C8+, C8+ Turn 7.10 Patient chair, options

båÖäáëÜ

7.10 Patient chair, options

Patient chair media block

Additional equipment which is approved for dental use (e g by EMS) and the hydro-colloid coolant supply (see page 73) may be connected to a media block on the base of the chair (observe manufacturers’ specifications for the additional equip-ment).

The media block is equipped with quick couplings for air and water and an outlet with a separate fuse (6.3A) for non-heat-ing equipment.

Sirona does not assume any liability for possible damage to the connected equip-ment!

Technical data and requirements

DVGW approval:

The DVGW approval of the treatment center expires if a media block is installed.

Water

Air

T 6.3 AH

Line voltage

Pressure Flow rate

Water

min. 2.5 bar

max. 6.0 bar

(corresponding to input pressure on treatment center)

max. 1000 ml/min

Air 4.4 ± 0.5 bar max. 70 Nl/min

59 42 896 D3417D3417.201.01.22.02 39

8 Dentist element Sirona Dental Systems GmbH8.1 Locking the dentist element Operating Instructions C8+, C8+ Turn

8 Dentist element

8.1 Locking the dentist element

Brake applied

Maximum load

Brake released

CAUTIONA = You must not place any objects on this dentist element!

Brake applied

Maximum load

Brake released

Option

A

A

59 42 896 D341740 D3417.201.01.22.02

Sirona Dental Systems GmbH 8 Dentist element Operating Instructions C8+, C8+ Turn 8.2 Adjusting the instrument position

båÖäáëÜ

8.2 Adjusting the instrument position

8.3 Swivel arm

CAUTIONIMPORTANT: Swivel arms that are locked in place must not be pushed backward! To reset, pull the instrument hose out again.

Click

NO

OK

1.

2.3.

59 42 896 D3417D3417.201.01.22.02 41

8 Dentist element Sirona Dental Systems GmbH8.4 Dentist element C8+ Cart Operating Instructions C8+, C8+ Turn

8.4 Dentist element C8+ Cart

Maximum load capacity

2kg max.

CAUTIONRisk of toppling over! Move cart slowly and only on even floors without any obsta-cles!

CAUTIONDistribute the additional loads on the den-tist element evenly!

59 42 896 D341742 D3417.201.01.22.02

Sirona Dental Systems GmbH 8 Dentist element Operating Instructions C8+, C8+ Turn 8.5 Starting an instrument

båÖäáëÜ

8.5 Starting an instrument

A = Unused holders should be sealed with a ball!

CAUTIONDo not operate the instrument without spray.Always place the instrument back in the correct holder.

NOTE iAlso observe the operating instructions for the treatment instruments and the video system.

CAUTIONUse only treatment instruments approved by Sirona!

NO

OK

NO

OK AA

A

59 42 896 D3417D3417.201.01.22.02 43

8 Dentist element Sirona Dental Systems GmbH8.6 Adjusting the driving air pressure Operating Instructions C8+, C8+ Turn

8.6 Adjusting the driving air pressure

Only by aservice engineer

alternatively

_

P

2

0

1

S

C8 +

12

S

P

0

100

120

4060

80

ENDO

P

2

0

1

S

C8 +

12

S

P

0

100

120

4060

80

ENDO

! !

+

P1

P2

or

59 42 896 D341744 D3417.201.01.22.02

Sirona Dental Systems GmbH 8 Dentist element Operating Instructions C8+, C8+ Turn 8.7 Instrument spray ON/OFF – chip blower

båÖäáëÜ

8.7 Instrument spray ON/OFF – chip blower

A = Spray OFF

B = Spray ON

C = Chip blower

alternatively

NOTE iFor the adjacent foot switch, "Spray ON" (B) is indicated by a green signal in the up-per left corner.

P

2

0

1

S

C8 +

12

S

P

0

100

120

4060

80

ENDO

P

2

0

1

S

C8 +

12

S

P

0

100

120

4060

80

ENDO

P1

P2

P1

P2

A B C

B A C

or

59 42 896 D3417D3417.201.01.22.02 45

8 Dentist element Sirona Dental Systems GmbH8.8 Instruments – adjusting the spray intensity Operating Instructions C8+, C8+ Turn

8.8 Instruments – adjusting the spray intensity

alternatively

A = Spray WATER

B = Spray AIR

C8+ Cart

Control choke can be adjusted by a service engi-neer only

P1

P2

P

2

0

1

S

C8 +

12

S

P

0

100

120

4060

80

ENDO

P

2

0

1

S

C8 +

12

S

P

0

100

120

4060

80

ENDO

_

P1

P2

! !

+

!

+-

1. 2.

3.

4.

5.

6.

A

B

or

59 42 896 D341746 D3417.201.01.22.02

Sirona Dental Systems GmbH 9 Dentist element options Operating Instructions C8+, C8+ Turn 9.1 Negatoscope

båÖäáëÜ

9 Dentist element options

9.1 Negatoscope

9.2 Tumbler holder

1. x 2. x

59 42 896 D3417D3417.201.01.22.02 47

9 Dentist element options Sirona Dental Systems GmbH9.3 Silicone handles, right/left Operating Instructions C8+, C8+ Turn

9.3 Silicone handles, right/left

9.4 Tray

A = Silicone mat, optional

Maximum load

9.5 Silicone mat

A

B

59 42 896 D341748 D3417.201.01.22.02

Sirona Dental Systems GmbH 9 Dentist element options Operating Instructions C8+, C8+ Turn 9.6 3-way SPRAYVIT syringe

båÖäáëÜ

9.6 3-way SPRAYVIT syringe

P

2

0

1

S

C8 +

12

S

P

0

100

120

4060

80

ENDO

P

2

0

1

S

C8 +

12

S

P

0

100

120

4060

80

ENDO

Option

134°C 274°F

Check

Click

3 min

59 42 896 D3417D3417.201.01.22.02 49

9 Dentist element options Sirona Dental Systems GmbH9.7 3-way syringe Operating Instructions C8+, C8+ Turn

9.7 3-way syringe

P

2

0

1

S

C8 +

12

S

P

0

100

120

4060

80

ENDO

P

2

0

1

S

C8 +

12

S

P

0

100

120

4060

80

ENDO

134°C 274°F

Check

3 min

59 42 896 D341750 D3417.201.01.22.02

Sirona Dental Systems GmbH 9 Dentist element options Operating Instructions C8+, C8+ Turn 9.8 Satelec Mini L.E.D. curing light

båÖäáëÜ

9.8 Satelec Mini L.E.D. curing light

Dentist element equipping options

Operating modes

CAUTIONAlways use the glare shield!

CAUTIONDo not stare into the beam path for longer periods, as this can damage your eyes.

CAUTIONAlso observe the safety information on the Mini L.E.D. on pp. 17 ff.

P

2

0

1

S

C8 +

12

S

P

0

100

120

4060

80

ENDO

Mode 1,2,3

0 5 10 Sec.

Mode 1

0 5 12,5 Sec.

Mode 2

0 5 10 15 20 Sec.

Mode 3

ATTENTION! Potentially dan-gerous optical radiation!

iKbKaK=ÄÉ~ãÉñáí=~éÉêíìêÉ

right! right!wrong! wrong!

59 42 896 D3417D3417.201.01.22.02 51

9 Dentist element options Sirona Dental Systems GmbH9.8 Satelec Mini L.E.D. curing light Operating Instructions C8+, C8+ Turn

Technical data

General technical data

Model: Mini L.E.D.

Weight of hand-piece without hose:

105 g

Dimensions: dia. 23 x 240 mm

Current draw of handpiece:

5 V DC / 0.65 A

Thermal safety: Overheat protection

Optical specification

Wavelength:Max. intensity:

420nm – 480nma

at 450nm

a. Only composite materials can be hard-ened which react to the specified wavelength. The Mini L.E.D. e.g., for Lucirin® is not suit-able (maximum adsorption 380 nm).

Light power dia.7.5 mm(standard ver-sion):

1100 mW/cm2

Light power dia.5.5 mm (optional, available from Satelec):

2,000 mW/cm2

Light power: 450 mW – 500 mW

Classification acc. to IEC 62471:

Risk group 2 with light bar removed

Hazard distance (HD) and exposure hazard value (EHV) according to IEC 62471

HD EHV

Blue light:Free group

907 mm 20.6

Blue light:Risk group 1

323 mm 2.6

Blue light:Risk group 2

- 0.01

Thermal hazard to the corneaFree group

- 0.97

59 42 896 D341752 D3417.201.01.22.02

Sirona Dental Systems GmbH 9 Dentist element options Operating Instructions C8+, C8+ Turn 9.9 SL or BL ISO C electric motor

båÖäáëÜ

9.9 SL or BL ISO C electric motor

Motor and coupling versions

NOTE iThe BL ISO C option is not available in all countries.

CAUTIONDamage to BL ISO C electric motor:The BL ISO C electric motor may be con-nected only to a treatment center intended for this motor. The suitability of the treat-ment center for operation with the BL ISO C electric motor is indicated by a label on the dentist element.

Depending on the equipment configura-tion, either collector motors of the SL line or brushless motors of the BL ISO C line can be connected to the treatment center. The motors of the SL line and the motors of the BL ISO C line all require separate control electronics.

It is not possible to combine collector and brushless motors.

Only Sirona electric motors may be con-nected to the treatment center!

BL ISO C motor

Brushless motors are designed as three-phase motors (without carbon brushes). They are characterized by precise con-trollability and longevity. Their speed range lies between 200 and 40,000 rpm (revolutions per minute). These motors can be sterilized.

The black (BK) coded instrument hose must be used for the BL ISO C motor. The BL ISO C motor is directly equipped with an ISO coupling. T1 Line and T2 Revo handpieces can thus be used (without an adapter). In comparison to the SL and BL motors, the BL ISO C motor has a higher torque.

BL-ISO motorC8+ hanger 3

BL ISO C motorC8+ holder3

BL ISO C

GN

0123

sir

ona.

BLIS

OC

59 42 896 D3417D3417.201.01.22.02 53

9 Dentist element options Sirona Dental Systems GmbH9.9 SL or BL ISO C electric motor Operating Instructions C8+, C8+ Turn

SL motor

Collector motors are DC motors in which the voltage supply is realized via carbon brushes. The speed range lies between 200 and approx. 40,000 rpm (revolutions per minute).

The green coded instrument hose (GN) must be used for the SL motor. The SL motor can be operated with two different motor couplings For more information, please refer to the "SL Motor Operating Instructions".

The SL motor is designed for direct oper-ation of T1 Classic handpieces. In order to connect e.g. T1 Line and T2 Revo hand-pieces, an ISO adapter must be used.

GNGN

59 42 896 D341754 D3417.201.01.22.02

Sirona Dental Systems GmbH 9 Dentist element options Operating Instructions C8+, C8+ Turn 9.9 SL or BL ISO C electric motor

båÖäáëÜ

Setting the speed

A = Preselected maximum speed

Speed +

Speed -

The set value is saved when the instru-ment is placed back in its holder.

B = Direction of rotation

Motor CCW

Motor CW

NOTE iCCW rotation is not saved when the in-strument is placed back in its holder.

C = Motor speed controlonly with the Sirona unit foot switch

alternatively

Error message for the BL ISO C motor option

If the BL ISO C motor is defective or was screwed on improperly, all LEDs will flash once per second when the motor is removed from holder 3.

B

A

C

Speed in % LED/display

1 20 40 60 80 100

1 - 4 X

5 - 14 X X

15 - 24 X

25 - 34 X X

35 - 44 X

45 - 54 X X

55 - 64 X

65 - 74 X X

75 - 84 X

85 - 94 X X

95 - 100 X

M

M

or

59 42 896 D3417D3417.201.01.22.02 55

9 Dentist element options Sirona Dental Systems GmbH9.10 SIROSONIC L scaler Operating Instructions C8+, C8+ Turn

9.10 SIROSONIC L scaler

A = Water +/-

B = Preselected maximum intensity

Intensity +

Intensity -

alternatively

CAUTIONThe set value is saved when the instru-ment is placed back in its holder.

C8 +

12

S

P

0

100

120

4060

80

ENDO

12

S

P

0

100

120

4060

80

ENDO

_+

__

+

+

12

S

P

0

100

120

4060

80

ENDO

60

100

120

4060

80

100

120

4060

80

100

120

4060

80

P1

P2

60

= 70

100

120

4060

80

+-

-+

= 60

wrong!

A B

A

right !

Power in % LED/display

1 20 40 60 80 100

1 - 4 X

5 - 14 X X

15 - 24 X

25 - 34 X X

35 - 44 X

45 - 54 X X

55 - 64 X

65 - 74 X X

75 - 84 X

85 - 94 X X

95 - 100 X

or

59 42 896 D341756 D3417.201.01.22.02

Sirona Dental Systems GmbH 9 Dentist element options Operating Instructions C8+, C8+ Turn 9.11 SIROSONIC L endodontic scaler

båÖäáëÜ

9.11 SIROSONIC L endodontic scaler

In endodontics mode, the maximum inten-sity of the ultrasonic handpiece is restricted to ensure safe operation.

A = Water +/-

B = Preselected maximum intensity

Intensity +

Intensity -

alternatively

CAUTIONThe set value is saved when the instru-ment is placed back in its holder.

A B

A

Power LED/display

1 20 40 60 80 100

Step 1 X

Step 2 X

Step 3 X

Step 4 X

Step 5 X

Step 6 X

or

59 42 896 D3417D3417.201.01.22.02 57

9 Dentist element options Sirona Dental Systems GmbH9.12 Rinsing the water lines Operating Instructions C8+, C8+ Turn

9.12 Rinsing the water lines

Rinse water lines

Microorganisms can grow in the water lines of the treatment center. Use a large amount of water for rinsing the lines prior to starting patient appointments.

1. Activate the cuspidor flushing of the cuspidor bowl for at least one minute.

Purge function

To reduce the amount of germs, the water lines of the water carrying instruments of the dentist element and the SPRAYVIT M multifunctional syringe of the assistant element are purged with water.

1. Remove the instruments to be rinsed and set the maximum water flow rate.

2. Remove the handpieces from the in-strument hoses.

3. If an SL motor is installed, plug the purge adapter A into the motor.

4. Place the instrument hoses back in the holder.

5. Remove the instrument from holder 2 and hold it above the cuspidor.

6. Turn the switch to the "Purge" posi-tion.The instrument hose water line is rinsed for 60 seconds.

NOTE iPressing and holding the footswitch B suspends the purge function.

7. Place the rinsed instrument back in holder 2.

8. Remove the next instrument (holder 3) and hold it above the cuspidor.After 5 seconds have elapsed, the in-strument hose water line is rinsed for 30 seconds.

9. Repeat the procedure for all instru-ments.

10. After completing the purge proce-dure, turn the switch back to the "OFF" position.

1.

A

1.

2.

3.

6. 10.

B

4.

5.

59 42 896 D341758 D3417.201.01.22.02

Sirona Dental Systems GmbH 9 Dentist element options Operating Instructions C8+, C8+ Turn 9.12 Rinsing the water lines

båÖäáëÜ

NOTE iIt is possible to rinse all instruments at once. The purge procedure is then execut-ed automatically.

11. Remove the 3-way syringe and hold it above the cuspidor.

12. Activate the water button for 30 sec-onds.

13. Replace the 3-way syringe.

59 42 896 D3417D3417.201.01.22.02 59

10 Assistant element Sirona Dental Systems GmbH10.1 Suction handpiece/saliva ejector Operating Instructions C8+, C8+ Turn

10 Assistant element

10.1 Suction handpiece/saliva ejector

A = Suction handpiece

B = Saliva ejector

A

B

wrong

59 42 896 D341760 D3417.201.01.22.02

Sirona Dental Systems GmbH 11 Assistant element - options Operating Instructions C8+, C8+ Turn 11.1 3-way syringes

båÖäáëÜ

11 Assistant element - options

11.1 3-way syringes

11.2 Microswitch for vacuum system control

11.3 Air jet pump

59 42 896 D3417D3417.201.01.22.02 61

11 Assistant element - options Sirona Dental Systems GmbH11.4 Satelec Mini L.E.D. curing light Operating Instructions C8+, C8+ Turn

11.4 Satelec Mini L.E.D. curing light

Operation: see Chapter 9.8

59 42 896 D341762 D3417.201.01.22.02

Sirona Dental Systems GmbH 12 Water unit Operating Instructions C8+, C8+ Turn 12.1 Cuspidor flushing time - factory settings

båÖäáëÜ

12 Water unit

12.1 Cuspidor flushing time - factory settings

Option

max.1 kg

P

2

0

1

S

C8 +

12

S

P

0

100

120

4060

80

ENDO

P

2

0

1

S

C8 +

12

S

P

0

100

120

4060

80

ENDO

30s

P

2

0

1

S

C8 +

59 42 896 D3417D3417.201.01.22.02 63

12 Water unit Sirona Dental Systems GmbH12.2 Cuspidor flushing time - reprogramming Operating Instructions C8+, C8+ Turn

12.2 Cuspidor flushing time - reprogramming

Option

alternatively

2s

10s 10 m

10s 10 m

2.1.

4.3.

5.

5.

C8+

C8+ Turn

P

2

0

1

S

C8 +

59 42 896 D341764 D3417.201.01.22.02

Sirona Dental Systems GmbH 12 Water unit Operating Instructions C8+, C8+ Turn 12.3 Tumbler filling - factory settings

båÖäáëÜ

12.3 Tumbler filling - factory settings

Option

alternatively

12.4 Tumbler filling - reprogramming

Option

alternatively

max.1 kg

P

2

0

1

S

C8 +

12

S

P

0

100

120

4060

80

ENDO

P

2

0

1

S

C8 +

12

S

P

0

100

120

4060

80

ENDO

4s

P

2

0

1

S

C8 +

8 +

P

100

120

4060

80

ENDO

8 +

P

100

120

4060

80

ENDO

2s

>3s <15s

2.

1.

3.

>3s <15s

P

2

0

1

S

C8 +

59 42 896 D3417D3417.201.01.22.02 65

12 Water unit Sirona Dental Systems GmbH12.5 Combination of rinsing position S with tumbler filling and flushing controlled by dentist element Operating Instructions C8+, C8+ Turn

12.5 Combination of rinsing position S with tumbler filling and flushing controlled by dentist element

Option

SP

++

P

2

0

1

S

C8 +

12

S

P

0

100

120

4060

80

ENDO

P

2

0

1

S

C8 +

12

S

P

0

100

120

4060

80

ENDO

SP +

S

SP +

S

SP

S

<3s

<3s

<3s

<3s

P

2

0

1

S

C8 +

59 42 896 D341766 D3417.201.01.22.02

Sirona Dental Systems GmbH 12 Water unit Operating Instructions C8+, C8+ Turn 12.5 Combination of rinsing position S with tumbler filling and flushing controlled by dentist element

båÖäáëÜ

Combination of rinsing position S with tumbler filling and flushing controlled by foot switch

Only by a service engineer

Optionmax.1 kg

++P1

P2

S

+P1

P2

S

+

S

P1

P2

S

S

P1

P2

S

P1

P2

59 42 896 D3417D3417.201.01.22.02 67

12 Water unit Sirona Dental Systems GmbH12.6 Assistant element control panel - cuspidor flushing Operating Instructions C8+, C8+ Turn

12.6 Assistant element control panel - cuspidor flushing

12.7 Assistant element control panel - cuspidor flushing - reprogramming

max.1 kg

30s

2s

10s 10 m

10s 10 m

2.1.

4.3.

5.

C8+

C8+ Turn

59 42 896 D341768 D3417.201.01.22.02

Sirona Dental Systems GmbH 12 Water unit Operating Instructions C8+, C8+ Turn 12.8 Assistant element control panel - tumbler filling

båÖäáëÜ

12.8 Assistant element control panel - tumbler filling

Operation

Reprogramming

P

S

1

0

2

4s

S

0

2

S

0

2s

>3s <15s

2.

1.

3.

>3s <15s

59 42 896 D3417D3417.201.01.22.02 69

12 Water unit Sirona Dental Systems GmbH12.9 Assistant element control panel - combination of mouth rinsing position S with tumbler filling and cuspidor flushing Operating

12.9 Assistant element control panel - combination of mouth rinsing position S with tumbler filling and cuspidor flushing

Only by a service engineer

Option

SP ++

P

S

1

0

2

SP +

S

SP +

S

SP

S

<3s

<3s

<3s

<3s

P

S

1

0

2

59 42 896 D341770 D3417.201.01.22.02

Sirona Dental Systems GmbH 12 Water unit Operating Instructions C8+, C8+ Turn 12.10 Fresh water bottle

båÖäáëÜ

12.10 Fresh water bottle

CAUTION

Use only Sirona fresh water bot-tles!

Fill withSirona: Dentosept P

CAUTIONReplace deformed, scratched or discol-ored bottles immediately!

Operating temperature: +10 °C – +45 °C.

Do not continue using the bottle after its maximum period of use has expired!

Example above: Replace bottle by Sep-tember 2014 at the latest

LE

MO

N

LEM

ON

!

! ! !

+

!

!

100 : 1

orH2O

2.1.

3.

4. 5.

!wrong

59 42 896 D3417D3417.201.01.22.02 71

12 Water unit Sirona Dental Systems GmbH12.11 Switching between tap water/fresh water C8+ Operating Instructions C8+, C8+ Turn

12.11 Switching between tap water/fresh water C8+

alternatively

P1

P2

P1

P2

+or

59 42 896 D341772 D3417.201.01.22.02

Sirona Dental Systems GmbH 12 Water unit Operating Instructions C8+, C8+ Turn 12.12 Hydrocolloid connection

båÖäáëÜ

12.12 Hydrocolloid connection

Extra equipment

OPEN

CLOSE

59 42 896 D3417D3417.201.01.22.02 73

12 Water unit Sirona Dental Systems GmbH12.13 Dürr wet suction system Operating Instructions C8+, C8+ Turn

12.13 Dürr wet suction system

Daily after consulting hours 1liter

10s

simultaneously

H2O

C8+ Turn

59 42 896 D341774 D3417.201.01.22.02

Sirona Dental Systems GmbH 12 Water unit Operating Instructions C8+, C8+ Turn 12.14 Amalgam separator

båÖäáëÜ

12.14 Amalgam separator

A = ! Please replace amalgam container !

B = !! Replace amalgam container !!

Error/fault

AMALGAM testat least 1x annually

NOTE iInformation on replacing the amalgam separator can be found on page 96.

2005

1 32 4 5 6 78 109 11 12 13 1415 1716 18 19 20 2122 2423 25 26 27 2829 3130

2004

1 32 4 5 6 78 109 11 12 13 1415 1716 18 19 20 2122 2423 25 26 27 2829 3130

2003

1 32 4 5 6 78 109 11 12 13 1415 1716 18 19 20 2122 2423 25 26 27 2829 3130

2002

1 32 4 5 6 78 109 11 12 13 1415 1716 18 19 20 2122 2423 25 26 27 2829 3130

....

100 %

95 %

0 %

0 %

DESINF

AMTEST

SAN

AMALG

DESINF

AMTEST

SAN

AMALG

DESINF

AMTEST

SAN

AMALG

AMTEST

SAN

AMALG

DESINF

DESINF

AMTEST

SAN

AMALG

AMTEST

SAN

AMALG

DESINF

AMTEST

SAN

AMALG

DESINF

AMTEST

SAN

AMALG

DESINF

AMTEST

!

!!

A

B

OK!

AMTEST

59 42 896 D3417D3417.201.01.22.02 75

12 Water unit Sirona Dental Systems GmbH12.15 Disinfection system Operating Instructions C8+, C8+ Turn

12.15 Disinfection system

A = ! If the DESINF indicator flashes,refill 1 liter of DENTOSEPT P!

Refill withSirona: Dentosept P

A

59 42 896 D341776 D3417.201.01.22.02

Sirona Dental Systems GmbH 12 Water unit Operating Instructions C8+, C8+ Turn 12.16 Conversion of water unit right-handed left-handed version

båÖäáëÜ

12.16 Conversion of water unit right-handed left-handed version

Conversion only possible on a C8+ Turn

CAUTIONDanger of falling objects! Prior to con-version, remove all objects loosely depos-ited on any components of the treatment center.

NOTE iPlease observe the minimum clearances specified in the document “Dimension Drawing, Technical Data”.

59 42 896 D3417D3417.201.01.22.02 77

12 Water unit Sirona Dental Systems GmbH12.16 Conversion of water unit right-handed left-handed version Operating Instructions C8+, C8+ Turn

59 42 896 D341778 D3417.201.01.22.02

Sirona Dental Systems GmbH 12 Water unit Operating Instructions C8+, C8+ Turn 12.16 Conversion of water unit right-handed left-handed version

båÖäáëÜ

59 42 896 D3417D3417.201.01.22.02 79

13 Operating light - option Sirona Dental Systems GmbH13.1 SIROLUX E Operating Instructions C8+, C8+ Turn

13 Operating light - option

13.1 SIROLUX E

ON/OFF – brightness reduction

Option

alternatively

Composite setting

Light intensity: 22000 lux


CAUTIONDo not use without transparent cover!

P

2

0

1

S

C8 +

12

S

P

0

100

120

4060

80

ENDO

P

2

0

1

S

C8 +

12

S

P

0

100

120

4060

80

ENDO

P

2

0

1

S

C8 +

P

2

0

1

S

C8 +

12

S

P

0

100

120

4060

80

ENDO

P

2

0

1

S

C8 +

12

S

P

0

100

120

4060

80

ENDO

wrong right

59 42 896 D341780 D3417.201.01.22.02

Sirona Dental Systems GmbH 13 Operating light - option Operating Instructions C8+, C8+ Turn 13.1 SIROLUX E

båÖäáëÜ

Focusing

CAUTIONWhen focusing, make sure you turn the cover cap only slightly and just up to its stop. If the cover cap is turned counter-clockwise past the stop, it will spring out of its catch and the halogen lamp can fall down.

700 mm28 ’’180 m

m

7 ’’

75 m

m3

’’

Click

59 42 896 D3417D3417.201.01.22.02 81

13 Operating light - option Sirona Dental Systems GmbH13.2 SIROLUX FANTASTIC Operating Instructions C8+, C8+ Turn

13.2 SIROLUX FANTASTIC

ON/OFF – brightness reduction

Option

alternatively

Composite setting



P

2

0

1

S

C8 +

12

S

P

0

100

120

4060

80

ENDO

P

2

0

1

S

C8 +

12

S

P

0

100

120

4060

80

ENDO

P

2

0

1

S

C8 +

P

2

0

1

S

C8 +

12

S

P

0

100

120

4060

80

ENDO

P

2

0

1

S

C8 +

12

S

P

0

100

120

4060

80

ENDO

59 42 896 D341782 D3417.201.01.22.02

Sirona Dental Systems GmbH 13 Operating light - option Operating Instructions C8+, C8+ Turn 13.3 LEDview

båÖäáëÜ

Focusing

CAUTIONWhen focusing, make sure you turn the cover cap only slightly and just up to its stop. If the cover cap is turned counter-clockwise past the stop, it will spring out of its catch and the halogen lamp can fall down.

13.3 LEDview

Operation of the LEDview operating light: see LEDview Operating Instruc-tions:REF 62 07 687

700 mm28 ’’200 m

m

8 ’’

100

mm

4 ’’

Click

59 42 896 D3417D3417.201.01.22.02 83

14 Care and cleaning instructions for the practice team Sirona Dental Systems GmbH14.1 Care, cleaning agents, and disinfectants Operating Instructions C8+, C8+ Turn

14 Care and cleaning instructions for the practice team

To maintain the value and safe function-ing of your treatment center, it is neces-sary to have it cared for, cleaned and dis-infected by the practice team regularly. This will minimize the risk of contamina-tion for patients and users and ensure proper functioning.

The national requirements and recom-mendations for hygiene and disinfection must be observed, e.g. Robert Koch Insti-tute (RKI), American Dental Association (ADA), Centers for Disease Control and Prevention (CDC), etc.

NOTE iThe time intervals specified for care, cleaning, and disinfection are reference values. Please adapt the time intervals to suit your personal method of working and your national requirements

14.1 Care, cleaning agents, and disinfectants

CAUTIONUnsuitable care and cleaning agents and disinfectants can damage or affect the surface of the unit or functions.To this end, only use care and cleaning agents and disinfectants that have been approved by Sirona.

A continuously updated list of approved agents can be downloaded from the Inter-net at "www.sirona.com". To access the online portal for technical documentation, follow the "SERVICE" / "Technical Docu-mentation" menu points in the navigation bar. The portal can also be accessed directly via the following address: http://www.sirona.com/manuals. Click on the "General Documents" menu point and then open the "Care, cleaning agents, and disinfectants" document.

If you do not have any access to the Inter-net, please contact your dental depot to order the list.

REF 59 70 905

59 42 896 D341784 D3417.201.01.22.02

http://www.sirona.com/manuals

Sirona Dental Systems GmbH 14 Care and cleaning instructions for the practice team Operating Instructions C8+, C8+ Turn 14.2 Patient chair

båÖäáëÜ

14.2 Patient chair

Upholstery/foot switch/chair

Care for and clean upholstery: The arti-ficial leather upholstery must be cared for and cleaned regularly (at least 1x/week), especially light colored upholstery.

CAUTIONUse only care and cleaning agents and disinfectants which have been approved by Sirona (see page 84, section 14.1)!

Disinfecting the upholstery


Do not use any other disinfectants!

Wipe disinfection

Foot control

Clean the bottom of the base plate using a damp cloth moistened in water.

59 42 896 D3417D3417.201.01.22.02 85

14 Care and cleaning instructions for the practice team Sirona Dental Systems GmbH14.2 Patient chair Operating Instructions C8+, C8+ Turn

MultiMotion headrestDisinfecting the surfaces

The surfaces can be spray and wipe disinfected with surface disinfectants.

Intensive cleaning and disinfection of the head support

The contact surface of the headrest can be removed to facilitate intensive cleaning and disinfecting if necessary.

The surfaces can be spray and wipe disinfected with surface disinfectants.

Press one side of head pad G inward from the outside (to unlock it) and re-move it in a upward direction.

NOTE iFast and frequent removal of the head pad from the front or rear can damage the snap-in noses.

Clean and disinfect the head pad and headrest.

Hook on the head pad again laterally.

CAUTIONDamaged pads, e.g. with scratched sur-faces, must be replaced.

G

For reorders:

Contact surface: REF 61 82 047

59 42 896 D341786 D3417.201.01.22.02

Sirona Dental Systems GmbH 14 Care and cleaning instructions for the practice team Operating Instructions C8+, C8+ Turn 14.2 Patient chair

båÖäáëÜ

Cleaning the filter, replacing the main fuse

If you notice any changes in media flows, check the water and air filters for permea-bility. The filters must be changed if nec-essary:

1. Switch the treatment center off at the main switch.The water and air supply is discon-nected.

2. Remove the cover A.

NOTE iAny remaining water flows out of the water filter when it is opened. You should there-fore place an absorbent cloth underneath the filter.

3. Unscrew and remove the screw-on cap of the water filter and/or the air fil-ter.

4. Check the filters and replace them if necessary.

5. Reinsert the rubber ring B in the screw-on cap.

6. Then plug the filter in, as shown in the drawing.

7. Screw the screw-on cap back onto the water unit.

C = Fuse T 10A H

C

A

B

59 42 896 D3417D3417.201.01.22.02 87

14 Care and cleaning instructions for the practice team Sirona Dental Systems GmbH14.3 Dentist element Operating Instructions C8+, C8+ Turn

14.3 Dentist element

Instrument hoses/instrument rack


CAUTIONEgress of air when changing hose:If the hose is removed from the 3-way sy-ringe when the treatment center on the dentist element is switched on, air es-capes from the connection flange. To pre-vent this, switch the treatment center off and release pressure from the 3-way sy-ringe before replacing the hose.

NOTE iFor care and cleaning of the motors, the straight and contra-angle handpieces, the highspeed handpiece and the SIROSONIC L scaler, please refer to the corresponding operating instructions.

Wipe disinfection

A = Unused holders should be sealed with a ball!

12

S

P

0

00

120

4060

80

ENDO

134°C 273,2°F

1.

2.

3.

4.

5.

6.

7.

8.

5x 5x

8.

A

5x 5x

7.

6.

2.

3 min

59 42 896 D341788 D3417.201.01.22.02

Sirona Dental Systems GmbH 14 Care and cleaning instructions for the practice team Operating Instructions C8+, C8+ Turn 14.3 Dentist element

båÖäáëÜ

3-way SPRAYVIT syringe

3-way syringe

Spray disinfection/wipe disinfection

134°C 274°F

2.

1.

3.

3 min

H O2

134°C 274°F

3 min

59 42 896 D3417D3417.201.01.22.02 89

14 Care and cleaning instructions for the practice team Sirona Dental Systems GmbH14.3 Dentist element Operating Instructions C8+, C8+ Turn

Satelec Mini L.E.D.

CAUTIONUse only care and cleaning agents and disinfectants which have been approved by Sirona (see page 84, section 14.1)

Always make sure that the Mini L.E.D. light is switched off before using disinfec-tants. Do not use any abrasive cleaners.

Prior to each use, check the light guides to make sure that no composite residues have adhered to them. If this is the case, remove these residues immediately and check to make sure that the surface of the insert has not been damaged. If you find any damage, replace the damaged light guide.

Surfaces


Wipe disinfection

Option

Option

3 min

P

2

0

1

S

C8 +

12

S

P

0

100

120

4060

80

ENDO

P1

P2

P

2

0

1

S

C8 +

12

S

P

0

100

120

4060

80

ENDO

P

2

0

1

S

C8 +

12

S

P

0

100

120

4060

80

ENDO

P

2

0

1

S

C8 +

12

S

P

0

100

120

4060

80

ENDO

134°C 274°F

3 min

59 42 896 D341790 D3417.201.01.22.02

Sirona Dental Systems GmbH 14 Care and cleaning instructions for the practice team Operating Instructions C8+, C8+ Turn 14.4 Assistant element

båÖäáëÜ

14.4 Assistant element

Suction handpiece/saliva ejector


CAUTIONEgress of air when changing hose:If the hose is removed from the 3-way sy-ringe when the treatment center on the as-sistant element is switched on, air es-capes from the connection flange. To prevent this, switch the treatment center off and release pressure from the 3-way syringe before replacing the hose.

Amalgam recycling

Wipe disinfection

Every 2 hours: 2 glasses

Every day after work1 liter

i

12

S

P

0

100

120

4060

80

ENDO

No amalgam!

According to manufacturer’s 3 min

1.

3.

2.

specifications

59 42 896 D3417D3417.201.01.22.02 91

14 Care and cleaning instructions for the practice team Sirona Dental Systems GmbH14.5 Water unit Operating Instructions C8+, C8+ Turn

14.5 Water unit

Water unit


Amalgam recycling


CAUTIONDo NOT use household de-tergents or acidic agents!

Daily before the lunch break and after consulting hours

The vacuum system is subjected to septic secretions, saliva and blood daily. For hygienic reasons the system must there-fore be disinfected with a detergent/disin-fectant approved by Sirona.

Daily

Sterilize the tumbler plate A.

CAUTIONDo not operate the unit without the tumbler plate!

Soap

0,75 lDesinf.

134°C 274°F

3 min

1 x/24 h

No amalgam! A

Soap

59 42 896 D341792 D3417.201.01.22.02

Sirona Dental Systems GmbH 14 Care and cleaning instructions for the practice team Operating Instructions C8+, C8+ Turn 14.5 Water unit

båÖäáëÜ

Air jet pump

1. Pour the disinfectant into the cuspi-dor.

2. Open the flap on the base of the water unit.

CAUTIONThe collecting tank may contain amalgam and must not be emptied into the wash ba-sin.

3. Remove the siphon and empty it into a special collecting tank.

4. Replace the siphon and close the flap again.

5. Activate the cuspidor flushing of the cuspidor bowl for at least one minute.

8 +

P

100

120

4060

80

ENDO

18

152229

29

162330

3101724

4111825

5121926

7142128

1 x

60s

2. 4.

5.

3.

weekly

C C8+ Turn

C8+

None Amalgam!

59 42 896 D3417D3417.201.01.22.02 93


Fresh water bottle

NOTE iPerform sanitation very 4 weeks!

Sanitation (1)

Fill withSirona: Dentosept P

alternatively

Switch OFF the systemfor 24 hours

P1

P2

12

S

P

0

100

120

4060

80

ENDO

P1

P2

2.

1.

3.

5.

6.

5.1 5.2 5.3 5.4

Tumbler filling 2x

4.

20 s

2.

4.

or

59 42 896 D341794 D3417.201.01.22.02


båÖäáëÜ

Fresh water bottle

Sanitation (2)

Fill with water

alternatively

P1

P2

12

S

P

0

100

120

4060

80

ENDO

P1

P2

2.

1.

3.

6.

4.

6.1 6.2

6.3

6.4

Tumbler filling 2x

H2O

5.

20 s

2.

or

59 42 896 D3417D3417.201.01.22.02 95


Amalgam separator

C = Change amalgam container!D = Change amalgam container

at least 1x annually

E = Signal during removal!

F = Clean siphon once a month

G = Do not reuse!

Amalgam recycling!

Replacement:Amalgam rotorREF 14 34 138

C

E

D

F

G

1.

2.

3.

4.

5.6.

C8+ Turn

59 42 896 D341796 D3417.201.01.22.02


båÖäáëÜ

Microbiological water test

Perform the microbiological water test at regular intervals and after periods of dis-use > 1 week. Start the checkups in inter-vals of no more than two weeks and adjust the time intervals depending on the results.

In addition to running laboratory tests, you can also use the "total count tester" as a simple means of performing this test. You can obtain the "total count tester" using REF 58 53 775 via the dental specialist dealer.

CAUTIONThe “Total Count Tester” has a maximum durability of 1 year after its date of delivery.

The cardboard disk contains a dehy-drated nutrient medium. It is activated by the sample and serves as culture medium for a number of bacteria. The number of germs provides information on the hygienic condition of the water.

Performing the test• Allow water to run out of the 3-way sy-

ringe for about 1 minute.• Then take a water sample from this

syringe.Fill in water up to the upper mark on the container. To neutralize the disin-fecting agent of the water sample, add approx. 1.5 g of fixing salt (sodium thiosulfate).Do not touch the inside of the contain-er or the part of the tester to be im-mersed.

• Immerse the tester in the filled con-tainer for 30 seconds.The cardboard disk with the nutrient medium will now absorb 1ml of the water sample.

• Remove the tester and shake off ex-cessive water. Empty the container completely.

• Place the tester into the empty con-tainer for incubation: Keep either for two days at room temperature or for 24 hours at a temperature of 35°C.

• Then count all germs found on the surface of the tester.

CAUTIONIf the number of germs significantly ex-ceeds 100, then sanitation is required (see next page).

30s

35?24 h

59 42 896 D3417D3417.201.01.22.02 97

14 Care and cleaning instructions for the practice team Sirona Dental Systems GmbH14.6 Sanitation of the treatment center Operating Instructions C8+, C8+ Turn

14.6 Sanitation of the treatment center

Disinfection system – sanitation

Sanitation must be performed:

• every 4 weeks

• after prolonged periods of disuse (> 1 week)

• if the germination index exceeds 100 germs per milliliter (see page 97).

A = 1% DENTOSEPT P99% H2O

B = 100% DENTOSEPT P

Starting sanitation

CAUTIONSanitation can only be started if the DIS-INF LED is not lit. If the DISINF LED is lit, Dentosept P must be refilled.

1. Press the SAN button and hold it down for at least 2 seconds.The SAN LED lights up and a short audible signal sounds.

The following steps are performed auto-matically:

• The mixing tank is emptied through the tumbler outlet.

• The SAN LED begins to flash as soon as the mixing tank is completely empty.

DESINF

AMTEST

SAN

AMALG

AMTEST

SAN

AMALG

DESINF+ = o.k.!

DESINF

AMTEST

SAN

AMALG

AMTEST

SAN

AMALG

DESINF

AMTEST

SAN

AMALG

DESINF

!

!

AMTEST

SAN

AMALG

DESINF =+ DEN

TOSE

PTP

DEN

TOSE

PTP

1.

2.

3.

5.

4.

>2s

6.

A

A

No sanitation possible,Refill with Dentosept P!

For reorders:

DENTOSEPT P 1 case = 6x1 liter, REF 33 18 156

For Canada/USA only:

1 case = 6x1 liter,REF 59 69 535

59 42 896 D341798 D3417.201.01.22.02

Sirona Dental Systems GmbH 14 Care and cleaning instructions for the practice team Operating Instructions C8+, C8+ Turn 14.6 Sanitation of the treatment center

båÖäáëÜ


Rinsing the tumbler outlet


• The mixing tank is filled with DENTO-SEPT P. The procedure takes approxi-mately 10s.The SAN LED flashes.

• The tumbler outlet is rinsed.The SAN LED flashes.

• After the rinsing procedure is complete, an audible signal sounds (two short beeps).The SAN LED continues flashing.

1.

OK!

B

ap-B

B

59 42 896 D3417D3417.201.01.22.02 99



Rinsing instruments


Rinse the water-carrying instruments with 100% DENTOSEPT P (B):

1. Remove the 3-way syringe and rinse it for at least 20s.

alternatively

2. Activate the spray function using the foot switch.

3. Remove an instrument.

4. Rinse the instrument for at least 15s, by activating the foot switch.

5. Repeat steps 3 and 4 for all instru-ments connected.

6. Switch off the treatment center.The LED indicating operational readi-ness on the control panel switches off.

Switch OFF the systemfor 24 hours

15s

1.

20s

2.

4.

3.

B

or

59 42 896 D3417100 D3417.201.01.22.02


båÖäáëÜ


Implement sanitation after 24h of effective time


1. Switch the treatment center on again after 24 hours have elapsed.The LED indicating operational readi-ness on the control panel lights up. The treatment center is in sanitation mode. The SAN LED is flashing. A permanent audible signal sounds (2 short beeps, 5s pause).

2. Press the SAN button and hold it down for approximately 3s.

The following steps are performed auto-matically:

• The mixing tank is emptied through the tumbler outlet.The SAN LED continues flashing.

1.

1.

3.

4.

4.

>3s

5.

B

B

2.

5s 5s

59 42 896 D3417D3417.201.01.22.02 101



A = 1% DENTOSEPT P99% H2O

• The mixing tank is filled with water and DENTOSEPT P.

• The tumbler outlet is rinsed with a solu-tion of 99% water and 1% DENTOSEPT P (A).The SAN LED is lit up constantly.

• After the rinsing procedure is complete, a permanent audible signal sounds (3 short beeps, 10s pause).The SAN LED is lit up constantly.

1.

2.

3.

5 - 10 s

A

A

3.

3. 10s 10s

59 42 896 D3417102 D3417.201.01.22.02


båÖäáëÜ


Rinsing instruments

Rinse the water-carrying instruments with a solution of 1% DENTOSEPT P and 99% water (A).

1. Remove the 3-way syringe and rinse it for at least 20s.

alternatively

2. Activate the spray function using the foot switch.

3. Remove an instrument.

4. Rinse the instrument for at least 15s, by activating the foot switch.

5. Repeat steps 3 and 4 for all connect-ed instruments.

The SAN LED switches off.Sanitation is complete.

15s

1.

20s

2.

OK!

3. + 5.

A

or

59 42 896 D3417D3417.201.01.22.02 103

14 Care and cleaning instructions for the practice team Sirona Dental Systems GmbH14.7 SIROLUX E operating light Operating Instructions C8+, C8+ Turn

14.7 SIROLUX E operating light

Replacing the halogen lamp

CAUTIONAlways turn the main switch of the lamp off before replacing the lamp (see page 28)!


CAUTIONOnly:REF 48 89 965Type OSRAM 64 440

CAUTIONUse only cleaning agents which are ap-proved by Sirona (see page 84, section 14.1)!


The reflector should be cleaned with a dry, lint-free cloth if necessary.Spots and fingerprints on the reflector can be removed with 70% alcohol.

i

59 42 896 D3417104 D3417.201.01.22.02

Sirona Dental Systems GmbH 14 Care and cleaning instructions for the practice team Operating Instructions C8+, C8+ Turn 14.7 SIROLUX E operating light

båÖäáëÜ

Cleaning or disinfecting the handles



NOTE iTo change the handle position, proceed as follows:

• Press and hold down the button.

• Slightly pull out the handle and turn it until it has reached the desired posi-tion.

• Release the button and let the handle lock in place.

59 42 896 D3417D3417.201.01.22.02 105

14 Care and cleaning instructions for the practice team Sirona Dental Systems GmbH14.8 SIROLUX FANTASTIC operating light Operating Instructions C8+, C8+ Turn

14.8 SIROLUX FANTASTIC operating light

Replacing the halogen lamp

CAUTIONAlways turn the main switch of the lamp off before replacing the lamp (see page 28)!


CAUTIONOnly use halogen bulbs REF 62 03 629!


Spray disinfection/ wipe disinfection

The reflector should be cleaned with a dry, lint-free cloth if neces-sary.Spots and fingerprints on the reflector can be removed with 70% alcohol.

i

59 42 896 D3417106 D3417.201.01.22.02

Sirona Dental Systems GmbH 14 Care and cleaning instructions for the practice team Operating Instructions C8+, C8+ Turn 14.9 LEDview

båÖäáëÜ

Cleaning or disinfecting the handles



NOTE iTo change the handle position, proceed as follows:

• Press and hold down the button.

• Slightly pull out the handle and turn it until it has reached the desired posi-tion.

• Release the button and let the handle lock in place.

14.9 LEDview

• Care and cleaning of the LEDview operating light: see LEDview Operat-ing Instructions:REF 62 07 687

59 42 896 D3417D3417.201.01.22.02 107

15 Options Sirona Dental Systems GmbH15.1 Working stool CARL Operating Instructions C8+, C8+ Turn

15 Options

15.1 Working stool CARL

Please observe the operating instructions for the CARL working stool: Order No. 63 16 819

15.2 PAUL working stool (not available in the Federal Republic of Germany)

Please observe the operating instructions for the PAUL working stool: Order No. 63 16 827

15.3 HUGO working stool

Please observe the operating instructions for the HUGO working stool: Order No. 61 94 240

59 42 896 D3417108 D3417.201.01.22.02

tÉ=êÉëÉêîÉ=íÜÉ=êáÖÜí=íç=ã~âÉ=~åó=~äíÉê~íáçåë=ïÜáÅÜ=ã~ó=ÄÉ=êÉèìáêÉÇ=ÇìÉ=íç=íÉÅÜåáÅ~ä=áãéêçîÉãÉåíëK

«=páêçå~=aÉåí~ä=póëíÉãë=dãÄe=OMMTJOMNR péê~ÅÜÉW==båÖäáëÅÜ mêáåíÉÇ=áå=dÉêã~åóaPQNTKOMNKMNKOOKMO===NOKOMNR ûKJkêKW= NOM=UVS fãéêáã¨=Éå=^ääÉã~ÖåÉ

páêçå~=aÉåí~ä=póëíÉãë=dãÄe

c~Äêáâëíê~ëëÉ=PNSQSOR=_ÉåëÜÉáãdÉêã~åóïïïKëáêçå~KÅçã

lêÇÉê=åçK RV=QO=UVS=aPQNT