fåëí~ää~íáçå=fåëíêìÅíáçåë=iáÖÜí=qê~Åâ=póëíÉã...specifically authorized by SIRONA. CAUTION Any person who assembles or modifies a medical electrical

kÉï=~ë=çÑW= NOKOMMS

båÖäáëÜ

pfoliru c kq pqf`

fåëí~ää~íáçå=fåëíêìÅíáçåë=iáÖÜí=qê~Åâ=póëíÉã

kÉï=~ë=çÑW= NOKOMMS

General information Sirona Dental Systems GmbHInstallation Instructions

60 53 461 D34942 D3494.031.01.02.02

Changes since the last version: 12.2004

Chapter or section, page

About this document

This document describes the installation of the SIROLUX FANTASTIC as a Light Track System.

You will require the drilling template for reliable and safe fastening to the ceiling.

• REF 60 53 503 Light Track System

The requirements for installing the SIROLUX FANTASTIC as a Light Track System model are described in the Instruc-tions SIROLUX FANTASTIC Light Track System, wall model, cabinet model.

• REF 60 53 529 Light Track System,wall model, cabinet model

General information

Sirona Dental Systems GmbH Installation Instructions

båÖäáëÜ
1 Before you begin .................................................................................................................. 5
1.1 Safety information........................................................................................ 61.2 Installation versions ..................................................................................... 7

1.3 Dimensions/Space requirements................................................................. 8

1.4 Installation in fixed network.......................................................................... 11

2 Delivery and transport ......................................................................................................... 132.1 Delivery........................................................................................................ 14

3 Installation............................................................................................................................. 173.1 Required tools.............................................................................................. 18

3.2 Determining the fastening points ................................................................. 193.3 Drilling the holes .......................................................................................... 20

3.4 Mains power voltage selection..................................................................... 21

3.5 Fastening and connecting the ceiling rails................................................... 233.6 Shortening and mounting the support tube.................................................. 24

3.7 Mounting the flexible support arm with lamp ............................................... 26

Contents

60 53 461 D3494D3494.031.01.02.02 3

Sirona Dental Systems GmbHInstallation Instructions

60 53 461 D34944 D3494.031.01.02.02

1 Before you begin
SIROLUX FANTASTIC Light Track System
60 53 461 D3494D3494.031.01.02.02 5

1 Before you begin Sirona Dental Systems GmbHInstallation Instructions

It is essential that you comply with the warning and safety information contained in the Installation Instructions.

All such information is highlighted by the signal words CAUTION, WARNING or DANGER.

DANGERIt is essential that you switch the line voltage OFF at the main switch of the building installation before beginning installation of the unit!

CAUTIONThe installation must be carried out in accordance with the requirements stated in our Installation Instructions.

CAUTIONThe installation may be carried out only by personnel specifically authorized by SIRONA.

CAUTIONAny person who assembles or modifies a medical electrical system complying with the standard IEC 60 601-1-1 (safety requirements for medical electrical equipment) by combining it with other equipment is responsible for ensuring that the requirements of this regulation are met to their full extent for the safety of the patients, the operators and the environment.

If any equipment not approved by SIRONA is connected, it must comply with the applicable standards:

- IEC 60 950-1 for information technology equipment and- IEC 60 601-1 for medical electrical equipment.

See also “Installation Requirements”.

In case of doubt, contact the manufacturer of the system components.

CAUTIONWireless phone interference with medical electrical equipment: To ensure safe operation of medical electrical equipment, the use of mobile wireless phones in practice or hospital environments is prohibited.

CAUTIONElectromagnetic compatibility: The unit should not be operated in the immediate vicinity of other devices (see also "Installation Requirements“). If this proves to be unavoidable, the unit should be monitored to ensure that it is used properly.

CAUTIONUse an ESD wrist band during installation.Connect it to the protective ground wire.

CAUTIONWhen opening the unit: Please observe the usual precautionary measures for handling PCBs (ESD). Touch a ground point to discharge static electricity before handling any components.

1.1 Safety information

60 53 461 D34946 D3494.031.01.02.02

Sirona Dental Systems GmbH 1 Before you begin Installation Instructions

båÖäáëÜ

The SIROLUX FANTASTIC is available in three different versions:

• As a ceiling model

• As a Light Track System

• as a wall and cabinet model

These installation instructions describe the installation of the SIROLUX FANTASTIC in the Light Track System ver-sion.

1.2 Installation versions

Light Track System

60 53 461 D3494D3494.031.01.02.02 7


1.3.1 Dimensions of SIROLUX FANTASTIC 1:20 Light Track System

1.3 Dimensions/Space requirements

Side view

*approx. 2500 98 1/2”

**approx. 2600 – 2800 102 1/2”–110 1/4”

approx. 150059”

77730 1/2”

* 735 29”

** 835 – 1035 32 7/8”–40 3/4”

166065 3/8”

Tube* Short support tube** Long support tube

60 53 461 D34948 D3494.031.01.02.02


båÖäáëÜ

197577 3/4”

70027 1/2”

30°

30°

Side view

60 53 461 D3494D3494.031.01.02.02 9


1.3.2 Dimensions of SIROLUX FANTASTIC 1:20 Light Track System with C8+, ProFeel+

Top view

264 10 3/8”

335°

25°

155°

155°

500 (min. 300)19 5/8” (min. 11 3/4“)

60 53 461 D349410 D3494.031.01.02.02


båÖäáëÜ

1 3-wire power cable N, L, PE, 2 x AWG 14 plus PE, (3 x 1.5 mm2).

2 Overcurrent circuit breaker 8 A - 16 A.

3 Power switch for lamp. The switch must be located in the same room as the Light Track System.

1.4 Installation in fixed network

L N

1

N

8 A - 16 A

L

3

2

60 53 461 D3494D3494.031.01.02.02 11


60 53 461 D349412 D3494.031.01.02.02

2 Delivery and transport
60 53 461 D3494D3494.031.01.02.02 13

2 Delivery and transport Sirona Dental Systems GmbHInstallation Instructions

2.1.1 Packaging

All SIRONA equipment is carefully checked and packed prior to shipment. Please carry out incoming inspection of the equipment in order to make sure that it was not damaged during transport.

• Check the packaging and the equipment for visible signs of damage.

• Check the shipment for completeness based on the attached “scope of supply” checklist.

NOTEiIf the shipment was damaged during transport, document all damage carefully and contact the responsible carrying agent immediately.

NOTEiDisposal: Return the packaging materials to SIRONA or dispose of them in compliance with the legal regulations applicable in your country.

2.1 Delivery

Dimensions (cm): 100 x 59 x 31

18 kg (40 lbs)

Dimensions:

4 kg/5 kg (8.8 lbs/11 lbs)

SIROLUX FANTASTIC lamp Support tube

Installation material

Installation material

Dimensions (cm): 210 x 40 x 22

31 kg (68.3 lbs)

Light Track System

Long support tube (cm): 115 x 12 x 12

Short support tube (cm): 75 x 12 x 12

(Inch): 40 x 23 x 12(Inch): 45 x 5 x 5

(Inch): 30 x 5 x 5

(Inch): 83 x 16 x 9

60 53 461 D349414 D3494.031.01.02.02

Sirona Dental Systems GmbH 2 Delivery and transport Installation Instructions

båÖäáëÜ

2.1.2 Scope of supply (see also page 14)

The following components are contained in the scope of supply of the SIROLUX FANTASTIC Light Track System model:

• Light Track System incl. installation material

• Tube support incl. installation material

• SIROLUX FANTASTIC lamp incl.:

− Lamp handles− Cable takeup

2.1.3 Transport

If possible leave the packaging attached to the unit during transport in order to protect it against damage.

Avoid severe jolts and vibrations!The lamp reflector is a sensitive component which therefore must be handled with care.

60 53 461 D3494D3494.031.01.02.02 15

2 Delivery and transport Sirona Dental Systems GmbHInstallation Instructions

60 53 461 D349416 D3494.031.01.02.02

3 Installation
60 53 461 D3494D3494.031.01.02.02 17

3 Installation Sirona Dental Systems GmbHInstallation Instructions

1. Scissors

2. Plumb line

3. Center punch

4. Hammer

5. Carbide drill bit

6. Impact drilling machine or percussion drill

7. Torque wrench

8. Metal-cutting saw

9. Spirit level

10. Offset screwdriver

• Adhesive tape

3.1 Required tools

1. 2. 3.

4. 5. 6.

7. 8. 9.

dia. 12 mm

10.

1/2“

60 53 461 D349418 D3494.031.01.02.02

Sirona Dental Systems GmbH 3 Installation Installation Instructions

båÖäáëÜ

DANGERShock hazard! Be sure to switch the line voltage OFF at the main switch of the building installation BEFORE beginning the installation procedure.

DANGERShock hazard! When determining the fastening points, make sure that none of them are located above electrical cables installed in the ceiling.

Preparing the drilling template

• Cut an opening in the drilling template at the location where the power cable is to be inserted.

• Insert the power cable through the opening in the dril-ling template.

Attaching the drilling template and center punching the fastening points

• Attach the drilling template to the ceiling according to the relevant instructions provided for that purpose.

• Center punch the three boldly encircled fastening holes and remove the drilling template again.

3.2 Determining the fastening points

500mm (min. 300mm)19 5/8" (min. 11 3/4")

60 53 461 D3494D3494.031.01.02.02 19


Important information on ceiling construction

WARNINGThe total weight of the SIROLUX FANTASTIC Light Track System is approx 31 kg.The ceiling construction must be suitable for mounting the SIROLUX FANTASTIC Light Track System (see “On-site Installation, Dimensions, Technical da-ta”).

WARNINGThe Light Track System may come loose from the cei-ling if not fastened properly. Always used fasteners which are appropriate for the ceiling constructure at hand.

WARNINGNever use a worn-out drill bit (decreased diameter).

For concrete ceilings

WARNINGThe heavy duty steel wall plugs supplied may be used only for concrete ceilings!

For other ceilings

WARNINGFor all nonconcrete ceilings, the ceiling construction must be checked for sufficient fastening substance and special wall plugs must be purchased from a speciali-zed dealer.

For wood joist ceilings, an (approx. 10 mm thick) an-chor plate is required, which can be made by a local fit-ter.

Two spacers can be made for suspended.

• Please provide detailed information on the load capaci-ty of the ceiling and purchase the appropriate installati-on materials from a specialized dealer.

1. Drill the wall plug hole depending on the condition of the ceiling and the installation materials (for concrete ceilings: approx. 70 mm deep with a hole diameter of 12 mm).

3.3 Drilling the holes

1.

60 53 461 D349420 D3494.031.01.02.02


båÖäáëÜ

3.4.1 230V mains power supply

• Unscrew the front and rear cover of the Light Track Sys-tem rail.

CAUTIONThe Light Track System rail is configured for 230V mains power at the factory. Changes are only required if the Light Track System shall be connected to 115V. Before connecting to mains power, check that the labels show the proper mains power selection.

1. Label positions for 230V mains power and fuse F1 with T2AH.

2. Wiring scheme of terminal Kl 11 for operation with 230V.

3.4 Mains power voltage selection

Kl 11

F1

1.

2.

Kl.11Fuse F1: T2AH

60 53 461 D3494D3494.031.01.02.02 21


3.4.2 115V mains power supply

• Unscrew the front and rear cover of the Light Track Sys-tem rail.

CAUTIONThe Light Track System rail is configured for 230V mains power at the factory. Changes are required before connecting to 115V mains power.

1. Remove the labels for 230V mains power and fuse F1 T2AH. Stick on the labels for 115V mains power and F1 T4AH.Exchange the fuse F1 T2AH with a fuse of type T4AH.

2. Rewire the leads on terminal Kl 11 as shown.

F1

Kl 11

1.

2.

Kl 11Fuse F1: T4AH

60 53 461 D349422 D3494.031.01.02.02


båÖäáëÜ

1. Run the power cable as shown and screw on the two ceiling mounts A. Install the cable for the composite function as well (if available). Check the two ceiling mounts horizontally with the spirit level. If necessary, compensate on the right or left at locations B.

2. Thread the power cable through the opening in the hol-der and fit the ceiling rail. Screw on the ceiling rail tight with four screws C and washers.Connect the power cable to terminal Kl 12:

– L (brown) to 12 L

– N (blue) to 12 N

– PE (green/yellow) to 12 PE

3.5 Fastening and connecting the ceiling rails

AB

B

1.

C

C

Kl 12

2.

60 53 461 D3494D3494.031.01.02.02 23


• Unscrew the slide cover (watch out for washer).

NOTEiIf the room height is between 260 cm and 280 cm, you will require the long support tube, which then must be shortened as required.

1. Shorten the support tube.

− Place the support tube in the slide and fasten it with the Allen screws.

− Transfer the 176 cm dimension from the floor to the support tube.

− Measure dimension X.− Loosen the Allen screws again slightly and remove

the support tube. − Cut dimension X off of the upper end of the tube.− Drill hole A 9 mm from the end of the tube with a

diameter of 5 mm +0.1 at the upper end of the tube opposite safety plate B (see illustration above).

NOTEiTip: To make sure that the support tube does not slip away while you're center punching and drilling it, you can unscrew safety plate B (see also page 26) and e.g. place a ruler underneath the flattened side of the tube connection to fix the tube in its position.

2. Measure the new length of the support tube, Y.

3.6 Shortening and mounting the support tube

Y

X

X

A

B

Dia.5 mm +0.1

1. 2.

60 53 461 D349424 D3494.031.01.02.02


båÖäáëÜ

3. Measure the length of the cable and stow the excess cable length in cable takeup C.

NOTEiThe remaining length of cable should correspond to the length of the support tube, Y.

4. Mount the support tube.

– Thread the cable incl. cable takeup into the support tube from above.

– Insert the support tube into the slide as shown and hammer in dowel pin D.

NOTEiDowel pin D is included in the scope of supply of the support tube.

– Tighten the two Allen screws E firmly.

500 Ncm ± 20 Ncm

DE

3. 4.

1C

60 53 461 D3494D3494.031.01.02.02 25


1. Attach slide cover A (see dismantling instruction on page 24).

Preparing the flexible lamp support arm

2. Pull the bellows back slightly on the flexible lamp arm. Using a screwdriver, carefully pry the two parts of support ring B apart on both sides and remove both ring halves.

3. Using a screwdriver, carefully pry apart the two covers C on both sides of the articulated arch and remove them.

4. Fit sleeve D (included in the scope of supply of the support tube) onto the shaft of the flexible support arm.

Mounting the flexible lamp support arm

5. Now loosen screw E on the support tube and pull out safety plate F, unless you already did this before drilling the hole in the support tube (see page 24).

3.7 Mounting the flexible support arm with lamp

1A

1

2

B

B

3. 5.

1

2

C

C

D

1

2

E

F

1. 2. 4.

60 53 461 D349426 D3494.031.01.02.02


båÖäáëÜ

6. Pull the cables of the support tube downward through the shaft and the articulated arch of the flexible lamp support arm.

7. Insert the shaft of the lamp support arm into the support arm from below and fasten this connection by refitting safety plate F.

NOTEiWhen assembling, make sure that the two stop pins G of the flexible support arm and the support tube are not located on top of each other.

8. Plug the cables together, roll them up in a loop and stow them in the arm.

NOTEiThe large connector should be stowed in the articulated arch so that it points toward the lamp. The small connector should be stowed in the articulated arch so that it points upward toward the support arm.

CAUTIONMake sure that the cables are not crushed.

9. Adjust the brake of the flexible lamp support arm with brake screw H.

NOTEiThe brake should be adjusted so that the support arm shows a slight braking resistance and does not automatical-ly move under its own weight.

9.

6. 7. 8.

1

2F

G

H

60 53 461 D3494D3494.031.01.02.02 27


10. Screw the covers of the ceiling adapter back on.

11. Push sleeve J upward onto the support tube, reattach covers K and support ring L to the flexible lamp support arm and push the bellows back onto the support ring (see also dismantling on page 26).

12. Attach the two handles M to the lamp while pressing the button. Four handle positions are possible.

10.

11.

M2

3

4K

L

J

12.

60 53 461 D349428 D3494.031.01.02.02

tÉ=êÉëÉêîÉ=íÜÉ=êáÖÜí=íç=ã~âÉ=~åó=~äíÉê~íáçåë=ïÜáÅÜ=ã~ó=ÄÉ=êÉèìáêÉÇ=ÇìÉ=íç=íÉÅÜåáÅ~ä=áãéêçîÉãÉåíëK

«=páêçå~=aÉåí~ä=póëíÉãë=dãÄe=OMMNJOMMQ péê~ÅÜÉW=ÉåÖäáëÅÜ= mêáåíÉÇ=áå=dÉêã~åóaPQVQKMPNKMNKMOKMO===NOKOMMS ûKJkêKW=NMU=NMV fãéêáã¨=Éå=^ääÉã~ÖåÉ

páêçå~=aÉåí~ä=póëíÉãë=dãÄefå=íÜÉ=rp^W få=`~å~Ç~W

c~Äêáâëíê~ëëÉ=PNSQSOR=_ÉåëÜÉáãdÉêã~åóïïïKëáêçå~KÅçã

páêçå~=aÉåí~ä=póëíÉãë=ii`QUPR=páêçå~=aêáîÉI=pìáíÉ=NMM`Ü~êäçííÉI=k`=OUOTPrp^

páêçå~=`~å~Ç~PORM=oáÇÖÉï~ó=aêáîÉ=J=råáí=Rjáëëáëë~ìÖ~I=låí~êáç=iRi=RvS`~å~Ç~

lêÇÉê=kçK SM=RP=QSN=aPQVQ

Documents

fåëí~ää~íáçå=fåëíêìÅíáçåë=iáÖÜí=qê~Åâ=póëíÉã...specifically authorized by SIRONA. CAUTION Any person who assembles or modifies a medical electrical