HT GROUP // Rambacher Straße 2 • 91180 Heideck • T + 49 (0) 9177 98 - 0 • F + 49 (0) 9177 98 - 180 • info@htgroup.de • www.htgroup.de

Medical Installations

Version November 7th 2016 – subject to technical alterations

SUTURE MATERIAL CABINET

The body of the suture material cabinet is made entirely of ground stainless steel. The front side consists of two glass doors. Glass shelves can

be fitted at various heights in the body. The suture material cabinet is installed flush into every wall system.

DIMENSIONS (standard design)

Height 600 mm

Width 1070 mm

Depth 170 mm

Clear depth (shelf) 155 mm

Installation height 1200 mm

BODY

Material made of stainless steel (Mat. no. 1.4301)

Shelves 8 mm single-pane safety glass (ESG) I able to be inserted at various heights

Quantity according to customer wishes

Mounting rails for the fitting of the shelves I two pieces for each shelf

Installation flush with every wall system

GLASS DOORS

Material 8 mm single-pane safety glass (ESG)

Locking system magnetic snap-lock

Door handles one doorknob for each door panel

Glass edging especially for glass doors I two pieces for each door panel

MATERIAL AND SURFACE TREATMENT

Disinfection resistant against cleaning agents and disinfectants

ADDITIONAL FEATURES

Suture material boxes space for four boxes (150 x 500 x 220 mm I special dimensions possible)

HT GROUP // Rambacher Straße 2 • 91180 Heideck • T + 49 (0) 9177 98 - 0 • F + 49 (0) 9177 98 - 180 • info@htgroup.de • www.htgroup.de

Medical Installations

Version November 7th 2016 – subject to technical alterations

HATCH

The hatch is a horizontal pass-through sliding system. The pass-through element is moved horizontally by hand. Frame and hatch door panel are

manufactured from ground or powder-coated stainless steel. The hatch may be installed to open either on the right or left.

DIMENSIONS

Clear frame width variable up to 1 m² (width x height)

Clear pass-through width A – 125 mm (with bow handle on both sides)

Frame outer dimension A + 100 mm

Wall thickness up to 250 mm

Installation height according to customer wishes

Length of door drive box 2 x A + 100 mm

FRAME

Material ground stainless steel I powder-coated (with surcharge)

Frame type closed frame I sliding in front of the wall

Tray ground stainless steel I welded to the frame

Substructure additional cross members for fixing

HATCH DOOR PANEL

Material ground stainless steel I powder coated (with surcharge)

Door handles bow handles I recessed handles

Colour as an option according to colour chart

DRIVE

Drive type handrail

Trolley with ball-bearing mounted profiled rollers and final dampers

SPECIAL FITTINGS

X-ray protection Pb 0.5–3 mm

HT GROUP // Rambacher Straße 2 • 91180 Heideck • T + 49 (0) 9177 98 - 0 • F + 49 (0) 9177 98 - 180 • info@htgroup.de • www.htgroup.de

Medical Installations

Version November 7th 2016 – subject to technical alterations

OR SLAVE CLOCK

Independent clocks/individual clocks

Quartz clock: Independent clocks for which manual setting is required when starting up, essentially without automatic summer/winter time change-

over. Mains connection is possible.

Radio-controlled clock: Independent, precise clocks which are synchronised by the German DCF77 time signal transmitter within an approx.

1500 km radius around Frankfurt/Main. Fully automatic clock hand movement control (of analogue clocks) and summer/winter time changeover are

present.

System clocks and master clock technology

Pulse slave clock: A system clock which is controlled by a master clock with 12/24 V pole changing minute/second pulses.

Signalling clock: Intelligent slave clock which is controlled by a TELNU master clock with a serial time string (seconds, minutes, hours, day, month,

day of the week and year) without any additional cable (operating voltage and data transfer via a two-wire cable).

Fitting

The clock is fitted into the mounting opening without the need for screws by means of spring compressors on the rear side. The opening section is

355 mm. The stainless steel mounting frame is pre-fitted on the rear with closed-pore, self-adhesive sealing tape.

DIMENSIONS

Standard clock face30 cm I as an option 25 cm/40 cm as special version

Housing diameter 36 cm

Detection range 20 cm

EQUIPMENT FEATURES

Housing material stainless steel (Mat. no. 1.4301)

Covering impact resistant polycarbonate

Clock face printing in accordance with DIN 41091

Clock face variant ZF and ZA as standard

Clock face base white RAL 9010

Clock face printing black RAL 9004

Hour/minute hand silk matt RAL 9005

Second hand blood orange

Total weight 1.1 kg

HT GROUP // Rambacher Straße 2 • 91180 Heideck • T + 49 (0) 9177 98 - 0 • F + 49 (0) 9177 98 - 180 • info@htgroup.de • www.htgroup.de

Medical Installations

Version November 7th 2016 – subject to technical alterations

TECHNICAL DATA

Bed frame

Square profiles 80 x 40 x 2 mm I 40 x 40 x 2 mm I 20 x 20 x 2 mm I made of ground stainless steel (Mat. no. 1.4301) I welded together

Bed housingrear and side panels made of 1.5 mm galvanised steel

Front panel1 mm galvanised steel I with plaster board glued to the rear

Colourpowder-coating according to HT colour chart

Opening I Closing

open position 90°: Space in the room approx. 2090 x 800 mm I closed position 0°: Bed is flush with the wall panels

Handle stainless steel bar handle

Mattress black synthetic leather

Bed fittings 2 x gas pressure string with 80 kg

Media rail (optional) with electrical sockets for power and IT

Lighting unit (optional) LED bed lamp (with surcharge)

DIMENSIONS

Width 2100 mm

Installation depth 252 mm

Height 1000 mm (in closed position)

Installation height 300 mm

Mattress 2008 x 908 x 80 mm

Space in open position approx. 2090 x 800 mm

HT BED UNIT

FOR PATIENT & ICU ROOMS

The HT Bed Unit is installed flush with the wall panels in ICUs and patient rooms. An ideal solution for visitors who want to stay overnight,

because the bed can be both set up and dismantled quickly. In the closed position the bed unit is flush with the wall panels. The HT Bed

Unit is an almost equivalent replacement of a normal bed.

4)

3)

1)

2)

1 Bed frame2 Bed housing3 Mattress4 Front panel