Section 1 - Active Tech Electronics · Frequency 50 kHz 1 MHz 1 MHz 200 kHz 200 kHz 100 kHz 100 kHz 100 kHz 100 kHz ... life: 400 hours typical, without backlight ... HVAC Multimeter

Phone 1 866 663 8233

THE ONE-STOP SHOP FOR ALL YOUR ELECTRONIC NEEDS

ELECTRONICSSUPPLIES

DEPOT

Section 1: Test & Measurement: 1-39 Telecom & Datacom: 40-46

1

Test & Measurement Selection Guide

MODELS 233 289 287 87V 83V 179 177 175 77-4Basic featuresTrue RMS readings ac ac+dc ac+dc ac ac ac ac

Basic dc accuracy 0.25% 0.025% 0.025% 0.05% 0.1% 0.09% 0.09% 0.15% 0.30%

Wide bandwidth 100 kHz 100 kHz 20 kHz 5 kHz

Auto/manual ranging

Digits 3-1/2 4-1/2 4-1/2 4-1/2 4-1/2 3-1/2 3-1/2 3-1/2 3-1/2

Counts 6000 50000 50000 20000 6000 6000 6000 6000 6000

MeasurementsVoltage ac/dc 1000 V 1000 V 1000 V 1000 V 1000 V 1000 V 1000 V 1000 V 1000 V

Current ac/dc 10 A 10 A 10 A 10 A 10 A 10 A 10 A 10 A 10 A

Motor Drive (ASD) Measurements

Resistance 40 MΩ 500 MΩ 500 MΩ 50 MΩ 50 MΩ 50 MΩ 50 MΩ 50 MΩ 50 MΩFrequency 50 kHz 1 MHz 1 MHz 200 kHz 200 kHz 100 kHz 100 kHz 100 kHz 100 kHz

Capacitance 10,000 µF 100 mF 100 mF 10,000 µF 10,000 µF 10,000 µF 10,000 µF 10,000 µF 10 mF

Temperature (+) 400°C (+) 1350 °C (+) 1350 °C (+) 1090 °C (+) 400°C

dB 60 dB 60 dB

Conductance 50 nS 50 nS 60 nS 60 nS

Duty cycle/pulse width / - / - / -Continuity with beeper

Diode test

Display Dual display

Analog bargraph

Backlight Two level Two level Two level Two level

Diagnostics and Data Min-Max recording

Min-Max recording/w time stamp

Fast Min-Max 250 µs 250 µs 250 µs

Display Hold/Auto (Touch) Hold

Relative Reference

USB interface

Data logging

TrendCapture

Readings memories Yes Yes

Lo Ohms

Other featuresLoZ impedance function

Real time clock

Integrated holster

Removable holster

Closed case calibration

Separate battery door

Completely Sealed/ WatertightAutomatic power off

Low battery indication

Operating temperature range -10C,+50C -20C,+55C -20C,+55C -20C,+55C -20C,+55C -10C,+50C -10C,+50C -10C,+50C

4-20 mA source24 V loop supplyWarranty and Electrical SafetyLimited Lifetime warranty

Warranty (years) 3

Input alert

Dangerous voltage indication

CAT II measurementsCAT III measurements 1000 V 1000 V 1000 V 1000 V 1000 V 1000 V 1000 V 1000 V 1000 V

CAT IV measurements 600 V 600 V 600 V 600 V 600 V 600 V 600 V 600 V 600 V

Page Number 11 10 10 10 10 11 11 11 11

MODELS 233 289 287 87V 83V 179 177 175 77-4

MULTIMETERS

Phone 1 866 663 8233

Selection Guide Test & Measurement

2

MULTIMETERS

MODELS 117 116 115 114 113 1587 1577 789 787Basic featuresTrue RMS readings ac ac ac ac ac ac ac ac ac

Basic dc accuracy 0.5% 0.5% 0.5% 0.5% 0.5% 0.09% 0.2% 0.1% 0.1%

Wide bandwidthAuto/manual ranging

Digits 3-1/2 3-1/2 3-1/2 3-1/2 3-1/2 3-1/2 3-1/2 3-1/2 3-1/2

Counts 6000 6000 6000 6000 6000 6000 6000 4000 4000

MeasurementsVoltage ac/dc 600 V 600 V 600 V 600 V 600 V 1000 V 1000 V 1000 V 1000 V

Current ac/dc 10 A 200 µA 10 A 400 mA 400 mA 1 A 1 A

Motor Drive (ASD) MeasurementsResistance 40 MΩ 40 MΩ 40 MΩ 40 MΩ 60 MΩ 50 MΩ 50 MΩ 40 MΩ 40 MΩFrequency 50 kHz 50 kHz 50 kHz 100 kHz 20 kHz 20 kHz

Capacitance 10,000 µF 10,000 µF 10,000 µF 10,000 µF

Temperature (+) 400 °C (+) 500°C

dBConductanceDuty cycle/pulse widthContinuity with beeper

Diode test

Display Dual display

Analog bargraph

Backlight

Diagnostics and Data Min-Max recording

Min-Max recording/w time stampFast Min-MaxDisplay Hold/Auto (Touch) Hold / - /- /-

Relative Reference

USB interface

Data logging real time

TrendCaptureReadings memoriesLo OhmsOther featuresLoZ impedance function

Real time clockIntegrated holster

Removable holster

Closed case calibration

Separate battery door

Completely Sealed/ WatertightAutomatic power off

Low battery indication

Operating temperature range -10C,+50C -10C,+50C -10C,+50C -10C,+50C -10C,+50C -20C,+55C -20C,+55C -20C,+55C -20C,+55C

4-20 mA source

24 V loop supply

Warranty and Electrical SafetyLimited Lifetime warrantyWarranty (years) 3 3 3 3 3 3 3 3 3

Input alertDangerous voltage indication

CAT II measurementsCAT III measurements 600 V 600 V 600 V 600 V 600V 1000 V 1000 V 1000 V 1000 V

CAT IV measurements 300V 600 V 600 V 600 V

Page Number 11 11 11 11 11 12 12 12 12

MODELS 117 116 115 114 113 1587 1577 789 787

Phone 1 866 663 8233

3

Meters

77-4 Digital Multimeters

Fluke 77-IV digital multimeter has thefeatures needed to repair most electricaland electronic problems. This meter issimple to use and has significantimprovements over Fluke's original 70Series with more measurement functions,conformance to the latest safetystandards, and a much larger displaythat's easier to view. It measures:

Wide 1000 V measurement range Average responding AC measurements 0.3% accuracy 10 Amps continuous

(20A for 30 seconds) Frequency and capacitance Resistance and continuity

MPN # Description 175/EFSP 175 Digital Multimeter177/EFSP 177 Digital Multimeter179/EFSP 179 Digital Multimeter179/EDA2-KIT Electronics Kit with 179 & accessoriesC25 Meter CaseTPAK ToolPakTM Hanging Solution

MPN # Description 77-4 77-4 Digital MultimeterC50 Meter Case for 70 Series

179/EFSP

179/EDA2-KIT

MPN # Description 233 Remote Display Multimeter

170 Series Digital Multimeters

Ideal for most electrical, electronic and electro-mechanical applications.

True RMS AC voltage and current readings 6000 count digital display Analog bargraph displayMin/Max/Average Frequency, capacitance, resistance

and continuity capabilities Auto Hold and Manual Hold Backlight display (177 & 179) Includes TL75 test leads, 9V battery

and manual. 80BK temperature probe included (179 only)

179/EDA2 Electronics Kit includes:179 digital multimeter, TL224 test leads, TL910 test probes, AC280 heavy duty hook clips, 80BK integrated temperature probe, C800 carrying case

11X Series Digital MultimetersMaximum voltage between any terminal and earth ground: 600 V, surge protection: 6 kV peak per IEC 61010-1 600 VCAT III,pollution degree 2, display digital: 6,000 counts,bar graph: 33 segments, updates 32 per sec.,operating temperature: -10 °C to + 50 °C,storage temperature: -40 °C to + 60 °C, batterylife: 400 hours typical, without backlight 113: Basic meter set & reconnect testing 114: A compact true-RMS meter for electrical

troubleshooting 115: A compact true-RMS meter

for field service technicians 116: HVAC Multimeter with temperature

and microamps for troubleshoot problems with HVAC equipment and flame sensors 117: Electricians’ Multimeter with non-contact voltage for

demanding settings like commercial buildings, hospitals & schools 117/322: Includes 117 meter, 322 clamp meter,

TPAK hanging strap, C115 case and TL75 test lead set

117

MPN # Description 113 Utility Multimeter114 Electrical Multimeter115 Multimeter116 HVAC Multimeter117 Electricians Multimeter117/322 Electrician’s Combo KitC50 Meter Case

Test & Measurement

233 Remote Display Multimeter233 True-rms Remote Display Digital Multimeter gives you ultimate flexibility in unusual measurement scenarios. Place the removable display where you can see it and then put the meter where it is convenient for you Measure up to 1000 V ac and dcMeasure up to 10 A

(20 A for 30 seconds) 10,000 µF capacitance range Frequency to 50 kHz Built in thermometer conveniently allows

you to take temperature readings without having to carry a separate instrument Resistance, continuity and diode test Low power wireless technology allows the

display to be carried up to 30’ away from the point of measurement for added flexibility. No interference with measurements The removable magnetic display can be

conveniently mounted where it is easily seenMake measurements without holding the meter

to improve visual focus on probes and augment safe electrical measurements

Phone 1 866 663 8233

Meters Test & Measurement

4


True-RMS Electronics Logging imeterswith TrendCapture.

Large 50,000 count, 31⁄2 inch 1/4 VGAdot matrix display with white backlight Logging function with expanded memory

for unattended monitoring Save multiple logging sessions before

PC download Two terminal 50 ohm range with

1 mΩ resolution, 10 mA source current Low pass filter for voltage and frequency

measurements on motor drives LoZ Volts. Low impedance voltage

function for eliminating ghost voltages. “i” button-on board help screens for

measurement functions Real time clock for automatic time

stamping of saved readings True-rms ac voltage and current for measurements on non linear signalsMeasure up to 10 A (20 A for 30 seconds) 50 mF capacitance range Peak capture to record transients as fast as 250 µsWithstands hazardous 8,000 volt spikes

MPN # Description 287 True-rms Electronics Logging Multimeter289 True-rms Industrial Logging Multimeter287/FVF FVF Software289/FVF FVF SoftwareFVF/SC2 FlukeView Forms with cable for 180 Series

289

MPN # Description 83-5 83-5 Industrial Digital Multimeter87-5 87-5 True RMS Industrial Digital Multimeter


Advanced functionality for exactingindustrial applications

10,000µF capacitance range forcomponents and motor caps Peak capture to record transients

at 250µsMeasure to 10A/20A for up to

30 secs. Auto and manual ranging for

maximum flexibility Increased safety by withstanding

8000V spike Built in thermometer (87-5) Includes TL75 test leads, AC72

alligator clips, removable holster, 9V battery, CD-ROM and manual. The 87-5 model includes atemperature probe

87-5

1577/1587 Insulation Multimeters A digital insulation tester with a true RMS digitalmultimeter in a single, compact, handheld unit.DMM measures AC/DC volts, DC millivolts, AC/DCmilliamps, resistance (0.1Ω to 50MΩ) & continuity. 1577 insulation test voltages 500V, 1000V.

Insulation test range 0.1MΩ to 600MΩ 1587 insulation test voltages 50V, 100V, 250V,

500V, 1000V. Insulation test range 0.01MΩ to2.0GΩ. Also frequency, capacitance, diode test,temperature, and Min/Max

1503/1507 Insulation Resistance Testers Ideal for troubleshooting, commissioning, andpreventative maintenance applications. 1503 insulation test voltages 500V, 1000V.

Insulation test range 0.1MΩ to 2000MΩ 1507 insulation test voltages 50V, 100V,

250V, 500V, 1000V. Insulation test range0.01MΩ to 10GΩ Includes probe, test leads, probes and alligator

clips and four AA alkaline batteries

MPN # Description 1503 1503 Insulation Resistance Tester1507 1507 Insulation Resistance Tester1577 1577 Insulation Multimeter1587 1587 Insulation Multimeter

1587

1507

T5 Electrical Testers T5 Electrical Testers checks voltage, continuity and current in one tool Available in 600V and 1000V models OpenJaw™ checks current up to 100A - without breaking the circuit Detachable SlimReach™ probe tips are customized for national

electrical standards

MPN # Description T5-600 Electrical Tester 600VT5-1000 Electrical Tester 1000VT5-H5-1AC KIT T5-1000 Tester, Holster, H5 and 1ACH5 Case for T5 Tester

43B Power Quality Analyzer

Power quality analysis with a scope and meter built in. Perform the measurements you need to maintain power systems, troubleshoot power problems and diagnose equipment failures.

Measures power harmonics, inrush currents, resistance, diode voltage, continuity and capacitance Continuously measure volts and amps

cycle-by-cycle for up to 16 days 20 measurement memories Includes 400A current clamp, TL224 test leads,

AC220 alligator clips, TP220 test probes, cable, softare, case & manualMPN # Description 43B/003 43B Power Quality Analyzer

Phone 1 866 663 8233

5

Meters

MPN # Description 365 365 Detachable Jaw True-rms AC/DC Clamp Meter373 373 True-rms AC/DC Clamp Meter374 374 True-rms AC/DC Clamp Meter375 375 True-rms AC/DC Clamp Meter376 376 True-rms AC/DC Clamp Meter with iFlex™381 381 Remote Display True-rms AC/DC Clamp Meter with iFlex™

365

375

Test & Measurement

365, 373, 374 & 375 True RMS AC/DC Clamp Meters 374/375 can read up to 600 V and

600 A and handle min/max, average and inrush recording 373 basic clamp meter offers improved performance and

maximum value for price-sensitive users 365 is a new, innovative Fluke clamp meter, offering a

thin, small jaw design that makes it easy to get aroundtightly packed wires.

Fluke 376 True-rms AC/DC Clamp Meter with iFlex™ iFlex flexible probe expands measurement to 2500 A acMin, max, average and inrush

recording to capture variationsautomatically Integrated low pass filter and state of

the art signal processing allows foruse in noisy electrical environmentswhile providing stable readings Proprietary inrush measurement

technology to filter out noise andcapture motor starting current exactlyas the circuit protection sees it

Fluke 381 Remote DisplayTrue-rms AC/DC Clamp Meterwith iFlex™ Wireless technology allows the

display to be carried up to 30 ft.away from the point ofmeasurement for added flexibilitywithout interference withmeasurement accuracy The removable magnetic display can

be conveniently mounted where it iseasily seen Radio transmitter automatically sets

the correct measurement range soyou do not need to change theswitch positions while taking ameasurement

SPECIFICATIONS 365 373 374 375 376 381Curent Range (AC/DC) 200A 600A (AC only) 600A 600A 999.9A 999.9AAC Current via iFlex 2500A 2500A 2500A 2500AVoltage Range (AC/DC) 600V 600V 600V 600V 1000V 1000VResistance 6000Ω 6000Ω 6000Ω 60Ω 60Ω 60ΩFrequency 60Ω 60Ω 60ΩInrush 100mS 100mS 100mS 100mSCAT CAT III 600V CAT III 600V CAT III 1000V CAT III 1000V CAT III 1000V CAT III 1000VMeasurement CAT IV 300V CAT IV 600V CAT IV 600V CAT IV 600V CAT IV 600V

Power Quality Clamp MeterThis clamp on meter is a combinationpower analyzer, power quality logger, andclamp meter, and is ideal for monitoringelectronic loads. Setup and troubleshoot variable

frequency drives and UPS systems -Verify correct operation by measuringkey power quality parameters Harmonics measurements - Uncover

harmonic issues that can damage ordisrupt critical equipment Inrush capture - Check start-up current

where spurious resets or nuisancecircuit breaker tripping occurs Load studies - Verify electrical system

capacity before adding loads

MPN # Description 345 Power Quality Clamp Meter

376

381

416D & 411D Laser Distance Meters The Fluke laser distance meters use the most advanced distance measuring technology.These meters are fast, accurate, durable, andeasy to use - just point and shoot. Their simpledesign and easy one-button operation means youspend less time measuring while increasingthe reliability of the answers that you need. Reduction of estimation errors,

saving both time and money The most advanced laser technology for

distance measurement Instant measurement with one-button operation Easy targeting with bright laser Quick calculation of area (square footage)

and volume Easy addition and subtraction of measurements Improved battery life from automatic

shut-off featureThe 416D additionally offers: Improved visibility with backlit,

three-line display Ability to measure up to 60 m (200 ft) Audible feedback of on and off modes Storage of the last ten measurements for

quick recall of distanceMinimum and Maximum function Strong environmental protection with

IP54 (water spray and dust proof) sealingMPN # Description 411D 411D Laser Distance Meter416D 416D Laser Distance Meter

411D

416D

Phone 1 866 663 8233


6

ScopeMeter® 120 Series

Rugged solution for industrial troubleshooting and installation applications. It’s a truly integrated test tool, with oscilloscope, multimeter and “paperless” recorder in one affordable, easy-to-use instrument.

Two 5,000 counts true-RMS digital multimeters Automatic measurements A dual-input TrendPlot™ recorder Connect-and-View™ trigger simplicity

for hands-off operation Shielded test leads for oscilloscope,

resistance and continuity measurements 10:1 Voltage Probe included with

124 for high frequency measurements Up to 7 hours battery operation Optically-isolated interface for PC connection

Fluke 190 Series II Scopemeter®Go Where Scopes Could Never Go BeforeThe new Fluke ScopeMeter 190Series II combine the highestsafety ratings and ruggedportability with the highperformance of a benchoscilloscope. Designed forplant maintenance engineersand technicians, these toughScopeMeter test tools go intoharsh, dirty, and hazardousindustrial conditions to testeverything frommicroelectronics to powerelectronics applications.The new 190 Series II is the one testtool you will reach for to tackle justabout any troubleshooting task. Theyinclude a multimeter, TrendPlot™ andScopeRecord™ roll paperless recorder modes and hands free operationwith Connect-and-View™ triggering, and much more: Two or four electrically isolated inputs CAT III 1000V / CAT IV 600V safety rated Choose from 60 MHz, 100MHz or 200MHz bandwidth models Fast sampling rate, up to 2.5GS/s with up to 400 ps resolution Deep memory: 10,000 samples per channel waveform

capture so you can zoom in on the details Dedicated 5000 Count digital

multimeter in 2 Channel models Quad meter measurements via

scope BNC inputs in 4 channelmodels Connect-and-View continuous

auto-trigger, single shot, pulsewidth, and video triggering ScopeRecord roll mode,

capture waveform sample data for up to 48 hours TrendPlot, trend measurement

readings for up to 22 days Advanced automatic measurements, power (Vpwm, VA, W, PF) and time

(mAs, V/s, w/s) IP-51 rated for dust and drip proof to withstand harsh environments Isolated USB ports for memory devices and PC connectivity Li-Ion battery for extended operating timespan Easy-access battery door to make it easy to swap batteries A handy slot to tether and lock down the oscilloscope while unattended

using a standard Kensington® lock

125/003

SPECIFICATIONS 123 124Bandwidth 20MHz 40MHzMax. Real Time Sample Rate 25MS/s 25MS/sMax. Repetitive Sample Rate 1.25GS/s 1.25GS/sRecord Length 512 bytes 512 bytesInput Sensitivity 5mV/div. to 500V/div. 5mV/div. to 500V/div. Video Trigger Vertical Resolution 8 bits 8 bitsMax. Vertical Sensitivity 1mV 1mVTime Base Range 20ns-1min/div 10ns-1min/divPost and Pre Trigger(-10 to +10 div) Trigger Source A, B & opt. Ext. Trig. Pod A, B & opt. Ext. Trig. PodEnvelope Mode 40ns Glitch Capture Measure Menu Continuous Autoset Auto. Setup Measurements 26 26Cursor Measurements ∅∅ T, 1/∆T, V, ∆V, rise- and fall timeScreen Memories 2 2Setup Memories 10 20USB Interface True RMS Multimeter 5000 Counts Volts, Amps, Ohms, Continuity, Diode, Temp.

MPN # Description 123/003 Mono ScopeMeter® 20MHz123/003S Mono ScopeMeter® 20MHz with SCC Kit124/003 Mono ScopeMeter® 40MHz124/003S Mono ScopeMeter® 40MHz with SCC Kit

MPN # Description PriceSCC120E SCC Kit (for 120 Series) - EnglishSCC120F SCC Kit (for 120 Series) - FrenchSCC290 SCC Kit (for 190 Series)

MPN # Description 190-062/AMS Color ScopeMeter, 60 MHz, 2 channels plus DMM/Ext.input190-062/AM/S Color ScopeMeter, 60 MHz, 2 channels plus DMM/Ext.input,

with SCC-290 kit included190-102/AM Color ScopeMeter, 100 MHz, 2 channels plus DMM/Ext.input190-102/AM/S Color ScopeMeter, 100 MHz, 2 channels plus DMM/Ext.input

with SCC-290 kit included190-104/AM Color ScopeMeter, 100 MHz, 4 channels plus DMM/Ext.input190-202/AM Color ScopeMeter, 200 MHz, 2 channels plus DMM/Ext.input190-202/AM/S Color ScopeMeter, 200 MHz, 2 channels plus DMM/Ext.input,

with SCC-290 kit included190-204/AM Color ScopeMeter, 200 MHz, 4 channels plus DMM/Ext.input190-204/AM/S Color ScopeMeter, 200 MHz, 4 channels plus DMM/Ext.input,

with SCC-290 kit included

190-204

ScopeMeter® Special Value Kit (SCC-Kit)

This kit contains:

FlukeView® software Optically isolated interface cable Protective hard-shell carrying caseKit ordered separately or with ScopeMeter®

(see S suffix)

Phone 1 866 663 8233

7

Test & Measurement Thermal Imagers

Thermal Imaging Made Easy! Ti100, Ti110, Ti125, TiR110, and TiR125 Thermal Imagers Technology isn’t working for you if it’s slowing you down. Fluke proudly introduces five new thermal imagers specifically designed to help you do more in less time, while being at home in the harshest of environments. A project that might normally take an hour can now be done in minutes. Our newest imagers are the lightest, most rugged, easiest-to-use professional imagers you can buy.

IR-OptiFlex™ focus system: Discover issues significantly faster withFluke’s revolutionary, ultra-rugged focus system. The IR-OptiFlex focussystem gives you optimum focus by combining focus-free ease-of-usewith the flexibility of manual focus on the same camera! IR-Fusion® technology: Enjoy the industry’s only point-and-shoot IR-

Fusion camera. Fluke patented technology blends digital and infraredimages into a single image to precisely document problem areas. Rugged one-hand operation: Experience the most rugged and reliable,

lightweight professional camera around. One-touch focus, laser pointer,and torch. Point-and-shoot simplicity. No one builds more rugged,ergonomic tools than Fluke.

Multi-mode video recording: Troubleshoot with the industry’s onlythermal imager that records focus-free video in visible light and infraredwith full IR-Fusion capabilities. Monitor processes over time, easilycreate infrared video reports, and troubleshoot frame-by-frame. Easilydownload to PCs for video viewing and analysis in the includedSmartView software. IR-PhotoNotes™ annotation system: Get an exact reference to your

problem area by capturing up to three digital photos per file. Addimages of equipment, motor nameplates, workroom doors or any otheruseful or critical information. Electronic compass: Make sure you and others know the location of the

problem. Compass readings easily appear in images and reports.

Includes: SmartView® software, 2 GB SD memory card, USB PC cable for image transfer to PC (all models), hand strap, Lithium-Ion removable andrechargeable smart batteries, AC charger/power supply, manual, CD manual, soft case and hard transport and storage case. Ti15 and TiR125 also includecard reader for image download, USB video cable and battery charger

MODEL Ti100 Ti110 TiR110 Ti125 TiR125

FEATURES Ti100 Ti110 TiR110 Ti125 TiR125Infrared resolution 160 x 120 160 x 120 160 x 120 160 x 120 160 x 120Focus mechanism Focus-free: IR-OptiFlex™ IR-OptiFlex™ IR-OptiFlex™ IR-OptiFlex™

1.2 m (4 ft) and beyond focus system focus system focus system focus systemThermal sensitivity (NETD) ≤ 0.10 °C ≤ 0.10 °C ≤ 0.08 °C ≤ 0.08 °C ≤ 0.08 °C

at 30 °C target temp at 30 °C target temp at 30 °C target temp at 30 °C target temp at 30 °C target temp(100 mK) (100 mK) (80 mK) (100 mK) (80 mK)

Temperature measurement range -20 °C to +250 °C -20 °C to +250 °C -20 °C to +150 °C -20 °C to +350 °C -20 °C to +150 °C(-4 °F to +482 °F) (-4 °F to +482 °F) (-4 °F to +302 °F) (-4 °F to +662 °F) (-4 °F to +302 °F)

IR-Fusion® technology Full infrared, PIP, Full infrared, PIP, Full infrared, PIP, Full visible, Full infrared, PIP, Full visible,Full infrared only Full visible, Color alarm Full visible, Color alarm AutoBlend™, Color alarms AutoBlend™, Color alarms

Electronic compass — Yes Yes Yes YesMulti-mode video recording — .AVI w/ MPEG encoding .AVI w/ MPEG encoding .AVI w/ MPEG encoding .AVI w/ MPEG encoding

and .IS3 radiometric and .IS3 radiometricVoice annotation — Yes (60 seconds) Yes (60 seconds) Yes (60 seconds) Yes (60 seconds)Streaming video output — — USB video output USB video output

MODEL Ti100 Ti110 TiR110 Ti125 TiR125

FLIR i3 & i5 Infrared CamerasThe smallest, lightest and most affordable thermal imaging camera on the market. Easy to use and requires no experience. Just"point-shoot-detect" to obtain high-quality thermal images that will immediately give you the thermal information you need.

Produces instant, point-and-shoot JPEG thermal imagery thatcarries all required temperature data and can be storedinternally or externally, sent and analyzed The fixed focus free lens makes using the FLIR i5 a snapWeighs only 365 g, and is easy to store in a belt pouch FLIR i-Series thermal imaging cameras withstand a 2 meter

drop. Watersplash proof with an IP43 rate Stores images with unique ID in radiometric JPEG format,

containing all temperature data on a standard miniSD card. FLIR Tools software is included and the camera is also

compatible with the more powerful FLIR Reporter

High accuracy of ±2°C or ±2% produces sensitive thermalimages for general purpose maintenance analysis. Measurestemperatures up to +250°C and detects temperaturedifferences as small as 0.10°C Thermal image quality: (i3) 60x60 pixels (i5), 100x100 pixels Field of view: (i3) 12.5°(H) x 12.5°(V), (i5) 21°(H) x 21°(V) Thermal sensitivity: (i3) 0.15°C, (i5) 0.10°C

MPN # Description i3 IR Camerai5 IR Camera

i5

Phone 1 866 663 8233


8

MPN # Description AM-510 AM-510 Commercial / Residential Digital Multimeter AM-520 AM-520 HVAC Digital MultimeterAM-530 AM-530 True-rms Electrical Contractor MultimeterAM-540 AM-540 Advanced HVAC MultimeterAM-550 AM-550 Industrial Multimeter

MPN # Description IR-710 IR-710 Infrared ThermometerIR-720 IR-720 Infrared ThermometerIR-712 IR-730 Infrared ThermometerIR-730 IR-740 Infrared ThermometerIR-750 IR-750 Infrared Thermometer

MPN # Description ACD-21SW ACD-21SW Swivel Clamp Meter

SPECIFICATIONS IR-710 IR-712 IR-720 IR-730 IR-750Distance to Spot (D:S) 10:1 12:1 20:1 30:1 50:1Temperature Range 0°F to 716°F 0°F to 1022°F -26°F to 1922°F -26°F to 2282°F -58°F to 2822°F

-18°C to 380°C -18°C to 550°C -32°C to 1050°C -32°C to1250°C -50°C to1550°C

Best Accuracy ±2% ±1.8% ±1.8% ±1.8% ±1.8%Display Resolution 0.1°C / 0.1°F 0.1°C / 0.1°F 0.1°C / 0.1°F 0.1°C / 0.1°F 0.1°C / 0.1°F

of reading < 999.9MIN/MAX Memory Temperature Display Tripod mount High and Low alarm USB interface Built in memory 99K-Type measurement

SPECIFICATIONS AM-510 AM-520 AM-530 AM-540 AM-550Safety rating CAT III 600V CAT III 600V CAT III 600V CAT III 600V CAT III 600V

CAT II 1000V CAT II 1000V CAT III 1000V CAT III 1000VTrue-rms AC Voltage (V) 600 750 750 1000 1000DC Voltage (V) 600 1000 1000 1000 1000AC & DC Current (A) 10 10 10 10 10Resistance (MOhms) 40 40 40 60 60Auto & Manual ranging Low pass filter Low Z Built-in flashlight LCD Counts 4,000 4,000 4,000 6,000 6,000Backlight Bar Graph Dual display Max/min hold Peak hold (crest)

ACD-21SW Swivel Clamp Meter New patented rotating head clamp design allows easyviewing of the measurements in tight or inconvenient toreach places. Simply rotate the body of meter to get anunobstructed view of the LCD display. 180 degree rotating head for the perfect display viewing Advanced VoltTect non-contact voltage detectionMeasures AC Current up to 400 ACA, AC/DC Voltage up

to 600V, Resistance and Capacitance Temperature measurement Audible Continuity, Auto Power Off & Data Hold Auto and manual ranging respectively for quick checks

and precise measurements Safety CAT III 600 V Test leads, battery (installed), Users Manual, Carrying

Case and type-K thermocouple are included

IR-700 Series Infrared Thermometers A complete line of high performance diagnostic tools designed for HVAC/R, electrical, industrial maintenance,automotive,quality control & fire prevention applications. Precise measurement with distance to

spot ratio from 10:1 to 50:1Wide temperatures ranges available up

to -58°F to 2822°F (-50°C to 1550°C ) Laser pointer for accurate targeting 8 seconds auto display hold for easy

read-out Adjustable emissivity for measuring

a variety of materials Dual LCD display with backlight Stores up to 99 data points (IR-750 only)

AM-500 Digital Multimeter Series The new AM-500 Digital Multimeter Series is designed for home repair, HVAC-R, electrical and electronic applications. Affordable and high performance. AM-510: Re-wire, troubleshoot and repair home

appliances and automotive problems AM-520: Key functions such as temperature,

micro amps for flame sensor troubleshooting &capacitance to check motor start-up AM-530: Measure and verify presence of voltage

in order to connect equipment or to performrepairs, run new wiring, check continuity ofelectrical connections & identify blown fuses AM-540: Key functions such as temperature,

dual thermocouples for temperature differential &low pass filter for frequency drives measurements AM-550: Packed full of features such as

true-rms, dual thermocouples, a low impedancefunction to detect stray voltage, and a low passfilter to accurately take measurements on variable frequency drives

AM-550

IR-720

MPN # Description 30XR-A 30XR-A Manual Multimeter33XR-A 33XR-A Manual Multimeter34XR-A 34XR-A Autoranging True RMS Multimeter37XR-A 37XR-A Autoranging True RMS Multimeter38XR-A 38XR-A Autoranging True RMS Multimeter38SW-A RS232 Cable and Software

SPECIFICATIONS 30XR-A 33XR-A 34XR-A 37XR-A 38XR-AAC/DC Volts 600V 750V/1000V 750V/1000V 750V/1000V 750V/1000VAC/DC Current 10A/10A 10A/10A 10A/10A 10A/10A 10A/10ABasic Accuracy 1% 0.7% 0.50% 0.10% 0.25%Resistance 20MΩ 4MΩ 40MΩ 40MΩ 40MΩCapacitance 4000µF 4000µF 400µF 400µFTemperature 1832°F/1000°C 1832°F/1000°C 2372°F/1300°CFrequency 40MHz 40MHz 40MHz 10MHzCounts 2,000 4,000 4,000 10,000 10,000

38XR-A

38SW-AFull Size Full-Featured Multimeters The XR series is designed for electronic, electrical, plant maintenance & HVAC use. 30XR-A & 33XR-A are average sensing 34XR-A, 37XR-A & 38XR-A are true-rms

measuring for voltage and current The Magne-Grip Holster with magnetic hanging strap

secures the meter to a convenient steel surface,freeing both hands for work. 38XR-A has a 4-20 mA loop current with % readout,

and is equipped with an optical PC interface (38SW-A optional RS-232 cable and software)

Phone 1 866 663 8233

9

Test & Measurement Meters

U1242B

U1252B

U1240B Series Handheld Digital MultimetersCheck more, fix more, spend lessWhether you need to inspect power supplies for harmonics, detect glitchesin switch systems or monitor differential temperature, these handheldDMMs are up to the task. Better yet, the pricemakes it easy to equip yourself with the functionsyou need to finish a day’s work with ease.U1241B Handheld Digital Multimeter, 4 DigitFeatures: 10,000 count display 0.09% basic DC voltage accuracy

and true RMS measurement Basic functions: DCV, DCI, ACV, ACI,

resistance, frequency, continuity, diode test Advanced functions: capacitance,

temperature, switch counter Adjustable backlighting Min/Max recording CAT III 1000V OV protectionU1242B Handheld Digital Multimeter, 4 DigitFeatures the same as the U1241B and: Advanced functions: capacitance,

temperature, switch counter, harmonic ratio, dual temperature, differential temperature

Retool Your Expectations with Agilent Handheld Tools!

MPN # Description U1241B Digital Multimeter, 4 digitU1242B Digital Multimeter, 4 digit

U1253B The World´s 1st OLED Handheld Digital MultimeterWhen you´re carrying the world´s first OLED handheld digital multimeter,you won´t have to squint to be sure that you´re reading it right. On the go or on the bench,you´ll get crystal-clear viewing indoors, even inthe dark and off-angle situations. Even thoughthe U1253B is loaded with high-performancefeatures and easy-to-use functions, it´s pricedto be easy on your pocket, too. You might evensay it´s revolutionary.Features: OLED display with 4.5-digit resolution 160° viewing angle 2000:1 contrast ratio True RMS AC+DC USB connectivity 1,000 data points for manual logging Built-in 20 MHz frequency counter and

square wave generatorIncludes: Silicone test leads & alligator clips Data logging software Test reports

MPN # Description U1253B OLED Digital Multimeter, 4 1/2 digit

U1250B Series Handheld Digital MultimetersBe well equipped from the startThe process of isolating faults is often unpredictable—but it can go fasterwith a versatile DMM that simplifies analysis and makes it easier to probehard-to-reach points.U1251B Handheld Digital Multimeter, 4 1/2 Digit features: 50,000 counts resolution on

both displays Up to 0.03% basic DCV accuracy True RMS AC measurement K-type temperature measurement IR-USB connectivity Manual and automatic data logging -20 °C to +55 °C operating temp.U1252B Handheld Digital Multimeter, 4 1/2 DigitFeatures the same as the U1251A and: Up to 0.025% basic DCV accuracy True RMS AC, AC+DC

measurement J & K-type temperature

measurement 20 MHz frequency counter Programmable square wave output

MPN # Description U1251B Digital Multimeter, 4 1/2 digitU1252B Digital Multimeter, 4 1/2 digit

MPN # Description U1231A 3 ½ Digit DMM w/ LED lightU1232A 3 ½ Digit DMM w/ LED light + AC/DC CurrentU1233A 3 ½ Digit DMM w/ LED Light ,Current and VSense

U1230 Series Handheld Digital Multimeters The Agilent U1230 Series is the best HH-DMM for the conditions you workin. Whether it’s dark, noisy or even dangerous, the multimeters help youprepare for these conditions with features that anticipate worse-casescenarios, but make everyday tasks easier. Using just one hand, you canilluminate the test area with its built-in flashlight while you measure andchange or choose measuring functions. You could safely detect hot wiresand easily make continuity measurements in noisy environments using theunique combination of beeping alert and blinking display/LED. Whateverthe working conditions, we have it covered. Built-in LED flashlight to illuminate test area Flashing backlight as visual alert during continuity tests in dim areas Vsense to perform non-contact voltage detection Data logging capability (stores up to 10 readings) IR connectivity to transfer data to PC for record

Phone 1 866 663 8233


10

Retool Your Expectations with Agilent Handheld Tools!

MPN # Description U1211A Handheld AC Clamp Current MeterU1212A Handheld AC + DC Clamp Multimeter w/ Temp MeasurementU1213A Handheld AC + DC High sensitivity Clamp Multimeter

w/ Temp Measurement + Duty cycle

U1271A & U1272A Dual Display Industrial Multimeters Shaped to fit, tailored to perform, and built to last Intelligent features: Low impedance mode,

Smart Ω, LPF, Qik-V, visual and audible continuity indicator for noisy environments Ergonomic: Better grip, large knob & buttons Rugged build: Dust and water resistant casing

(certified to IP 54) Easy fuse replacement via battery access Easy data logging to PC and internal memoryTrue RMS: U1271-AC, DC U1272-AC, DC, AC+DC

U1273A Industrial Multimeter Our new industrial DMM, the U1273A model, is re-invented with an OLED display that ensures crystalclear viewings – even in off-angle situations! U1270Series are ergonomically designed, water and dustresistance, and full with intelligent features. Superb indoor viewing with OLED display’s

2000:1 contrast ratio Clear and distinct reading even at off-angle

situations with its 160 degree viewing angle Improved accuracy and resolution to meet

traditional industrial requirements (30,000counts resolution with 0.7% for ACV accuracy) Intelligent features to improve productivity

and safety (LPF, LoZ, Smart Ω) Dust and water resistant casing

(IP 54 compliant)

MPN # Description U1271A Industrial MultimeterU1272A Industrial Multimeter

MPN # Description U1273A Industrial Multimeter

U1272A

U1190 Series Clamp Meters Agilent’s U1190 series clamp meters are packed with awealth of features to help you work more efficiently andmore safely. Housed in robust cases, each model comeswith an innovative wire separator that helps you isolateand measure individual wires in a bundle. The built-inLED flashlight illuminates your test area and Vsenseperforms non-contact voltage detection. The unique wire separator allows you to easily

separate and measure a desired wire in a bundle Data Hold, Min or Max recording LCD display with maximum reading of 6,000 counts Display backlight/built-in LED flashlight

(U1192A, U1193A & U1194A) Vsense performs non-contact voltage detection

(U1192A, U1193A & U1194A) Built-in LED flashlight illuminates test area

(U1192A, U1193A & U1194A) Current measurement up to 600 A

(U1193A & U1194A) Digital multimeter (DMM) with Resistance,

Capacitance (U1192A, U1193A & U1194A), DCV, ACV, DCμA (U1194A), ACμA (U1194A), Continuity and Diode test measurements

CAT III 600 V / CAT IV 300 V safety rating

MPN # Description U1191A Clamp MeterU1192A Clamp MeterU1193A Clamp MeterU1194A Clamp Meter

U1177A IR-to-Bluetooth Adapter Agilent U1177A Infrared (IR)-to-Bluetooth® adapter offers wireless remoteconnectivity solution via Bluetooth® connection simply by attaching theadapter to the IR port of an Agilent handheld digital multimeter. Thewireless remote connectivity is set up when an Agilent handheld digitalmultimeter is connected to U1177A and an Android device (tablet or smartphone) with the installed software. Every U1177A also has a unique MediaAccess Control (MAC) address. User can quickly and easily scan for theright U1177A using their Android device and pair up with the U1177A. Compatible with Agilent U1230, U1240 (with U1179A IR bracket),

U1250 and U1270 series handheld digital multimeters Operated by two 1.5 V AAA batteries

MPN # Description U1177A IR-to-Bluetooth Adapter

U1194A

U1210A Series Handheld Clamp MetersHandle big currents—safelyFor electrical distribution cables up to two inchesin diameter, the U1210B Series handheld clampmeters enable high-current measurements withoutbreaking the circuit. They also include DMMcapabilities—resistance, capacitance, frequencyand temperature—to simplify troubleshootingduring installation and maintenance. Large 2in clamp opening High measurement capability of up

to 1000 A for AC, DC or AC+DC (DC current U1212/3A only)

Includes full featured DMM with resistance,capacitance, frequency, temperature(U1212/3A only) functions and duty cycle % (U1213A only). Manual and auto ranging

Includes standard test leads with 19 mm and 4 mm probes and soft carrying case

Phone 1 866 663 8233

11

Test & Measurement

Phone 1 866 663 8233

Meters

U1730C series Handheld LCR MetersNow you can measure at frequencies as high as 100 kHz, a capabilitythat is typically found only in benchtop meters. With the autoidentification, Ai which conveniently displays component type anddetailed component analysis such as Z, ESR, DCR, you can getmeasurements done faster. Better yet, the battery lasts up to 16hours, ideal for testing on the go. With the U1730 Series, you canperform quick, basic LCR measurements at your convenience, without burning a hole in your pocket. 20,000 counts resolution 0.2% accuracy Wide LCR ranges with 3 to 5 selectable test frequencies (Up to

100 kHz for U1733C) Auto identification(Ai) which automatically determines and displays

component type and measurements Detailed component analysis with DCR, ESR, Z, D, Q, Ө functions Battery life of 16 hours/Ac-powered IR-to-USB connectivity for data logging to PC

MPN # Description U1701B Capacitance Meter

U1701B Handheld Capacitance Meter 11,000 counts

resolution w/dual displayWide measurement

range from 0.1 pF to 199.9 mF Visible and audible

tolerance mode for easycapacitor sorting Compare mode with 25

sets of non-volatileHigh/Low limit settings Records Minimum,

Maximum and Averagereadings Relative mode and Data

Hold function MPN # Description U1731C LCR Meter 120Hz/1KHz test frequenciesU1732C LCR Meter 120Hz/1/10KHz test frequenciesU1733C LCR Meter 120Hz/1/10/100KHz test frequencies + DC Resistance

Features: 20 or 40 MHz bandwidth with advanced triggering 125,000 points/channel waveform memory depth 11 built-in measurement functions, including voltmeter,

ohmmeter and auxiliary meter Zoom and dual waveform functions.

FFT function (U1604A) Remote control & data transfer

via PC Link application software USB 2.0 interface connectivity

Includes:2 pairs of 10:1 Scope probe, Three DMM alligator clips, two DMM test probe leads hook clips, two DMM groundalligator clips, AC adapter with power cable, product reference CD-ROM, 1X Scope probe (CAT II, 300V), 10x Scope probe (CAT II, 600V), DMM test leads,USB cable and NiMH battery pack 4500 mA, Quick Start Guide and Certificate of calibration.

MPN # Description U1602B 20 MHz OscilloscopeU1604B 40 MHz Oscilloscope

MPN # Description U1610A 100 MHz OscilloscopeU1620A 200 MHz Oscilloscope

ACCESSORIESMPN # Description U1602B-001 USB Host for U1604A OscilloscopeU1604B-001 USB Host for U1604A OscilloscopeU1590A Soft Carrying CaseU1562A Passive Probe, 100:1, 300 MHz, 1.2 m

U1604B U1600B Series - 20MHz and 40MHz Handheld Digital OscilloscopesMake high-performance measurements on the goOur handheld scopes are actually three instruments in one: a color scope, a basic DMM, and a data logger that sends DMM readings to a PC. Designed for a wide range of installation and maintenance applications,U1600 Series enables clear waveform viewing, easy waveform analysis and quick isolation of signal glitches.

U1610A and U1620A - 100MHz and 200MHz Handheld OscilloscopeWorld’s first handheld scope with VGA TFT LCD displayAgilent’s NEW U1610A/U1620A oscilloscope takes troubleshooting and maintenance task to a whole newlevel by being the world’s first handheld scope with three viewing modes on a VGA TFT LCD display. Whetheryou’re working in a poorly lit environment, or under the glaring sun, the revolutionary display ensures that youcan analyze waveforms effortlessly under all lighting conditions by 3 selectable viewing modes (indoor, outdoorand night vision mode). Coupled with 2 Mpts memory depth, it enables you to capture long, non-repeatingsignals with excellent zooming capabilities onto selective glitches. Further complementing your viewingexperience is the 5.7 inch screen that allows signal overviews to be analyzed on a wider viewing area. Features: 5.7 " VGA TFT LCD display with 3 selectable viewing modes (indoor, outdoor and night vision) 2 Mpts memory depth and 2 GSa/s sampling rate allows detailed analysis of captured glitches 100/200 MHz bandwidth with two isolated channels 10,000-count resolution on DMM display Channel-to-channel isolation with CAT III 600 V safety ratings Data logging capability and USB connectivity

U1620A


Phone 1 866 663 8233 12

MPN # Description MN16A Mini MultimeterMN16A-KIT* Mini Multimeter Kit

Digital Mini Multimeter AC/DC voltage

& current,resistance,capacitance, frequency, Type K temperauture Auto power off, disable feature With rubber holster, 9V battery,

bead wire Type K temperatureprobe & test leads

MN16A-KIT: includes CT20 tester,DV20 voltage detector, CA900 pouch

Digital Mini Multimeter Large displayMeasures AC/DC Voltage and DC

Current to 10A, Resistance (withContinuity and Diode functions),and Temperature to 1400°F(760°C) Includes rubber holster test leads

and Type K thermocouple probe

MPN # Description MN35 Mini Multimeter

MPN # Description EX210 Multimeter + IREX230 Multimeter + IR

Mini Digital Multimeters + IRIdentify overheating motors or locatehot spots on electrical panels andHVAC vents without contact Large backlit dual LCD Low current capability Input fuse protection Auto power off

and Data HoldWith test leads,

bead wire temperature probe (EX230) & 9V battery

EX503 EX505Averaging True RMS

4000 count 4000 countResistance Resistance

Capacitance CapacitanceFrequency Frequency

Temperature

EX210 EX2302000 count 4000 count

4:1 Distance to 4:1 Distance totarget ratio target ratioMax Hold Relative Mode

Type K Temp.Capacitance

FrquencyDuty Cycle

Professional Digital Multimeters Double molded for waterproof (IP67) protection 0.5% basic accuracy High contrast 4000 count LCD backlit display 1000V input protection on all ranges Temperature measurement

-50 to 1382°F (-45 to 760°C) Relative Mode Data Hold and Auto Power OffWith double-molded test leads, bead wire

temperature probe (EX505) & 9V battery

MPN # Description EX503 MeterEX505 Meter

500 Series MeterHeavy Duty Industrial MultiMeters Waterproof(IP67) rugged design for heavy duty use 6000 count and 40,000 count models

for high resolution 1000V input protection on all functions Dual sensitivity frequency functions Large backlit LCD with bargraph Duty Cycle function Diode open circuit voltage of 2.8V DC Auto power off with disable featureMin/Max/Relative/Data Hold Complete with double molded test leads,

magnetic hanging strap, Type K bead wiretemperature probe, carrying case, and one 9V battery

MPN # Description EX520 MeterEX530 MeterEX540 Meter

300 Series Meters 0.5% basic accuracy Non-contact voltage

from 100 to 600VAC Auto Power Off conserves battery life

(EX320, EX330) Low battery indicator Complete with stand, test leads, protective

holster, temp. probe (EX330), and batteries

MPN # Description EX310 MeterEX320 MeterEX330 Meter

MPN # Description EX411 MeterEX420 MeterEX430 MeterEX470 Meter

EX310 EX320 EX330Manual ranging Autoranging Autoranging

2000 count 2000 count 4000 countBattery Test Max Hold Data Hold

Data Hold Type K Temp.CapacitanceFrequencyDuty Cycle

EX411 EX430 EX470Manual ranging True RMS IR Thermometer

True RMS Autoranging True RMSCapacitance AutorangingFrequency CapacitanceDuty Cycle Frequency

Duty Cycle

EX520 EX530 EX540True RMS True RMS Wireless frequency

6000 Count 40,000 Count (914MHz)Type K Temp. Type K Temp. Data acquisitionCapacitance Peak Hold Remote receiver

Capacitance with USB cable

400 Series MeterRugged multimeters featuring models with built-in non-contactInfraRed Thermometer and True RMS functions Low current capability down to 0.1µA Audible and visual input alerts IR thermometer: 8:1 distance to target ratio Includes CAT III test leads, holster, temp.

probe (except model 450) and 9V battery

AC Clamp Meter + NCV Integrated Non-Contact Voltage Detector Quickly check for the presence of live wires before testingMultimeter functions include AC/DC Voltage, Resistance,

Capacitance, Frequency, Temperature, Duty Cycle, Diodeand Continuity Jaw opening: 1.2" MA250/410), 1.5" (MA620/640) Relative Mode for Capacitance Zero, and Offset Adjustment Data Hold Auto Power OffWith test leads, temperature

probe, batteries & case

13

Mini Analog Multimeter Easy to read analog display 5 functions: AC/DC voltage, DC

current, Resistance and Decibel 5% full scale accuracyMPN # Description 38073 Multimeter

Electrical Test Kit

MN24 - Manual Ranging CAT II-600V MiniTec™ MultiMeter with7 functions including 1.5V and9V Battery tests under load 40130 - Non-Contact Voltage

Detector. Detects AC Voltage from100VAC to 600VAC withouttouching the source ET15 - Receptacle Tester for

detecting faulty wiring in 3-wirereceptacles and five wiring faults

MPN # Description MN24-KIT Multimeter

MiniTec™ Autoranging Digital Multimeter 11 functions: AC/DC Voltage

and Current, Resistance,Capacitance, Frequency, Temperature to 1400°F (760°C), Duty Cycle, Continuity & Diode Test

MPN # Description MA220 Clamp Meter

Test & Measurement

800 Series Clamp MeterWith True RMS Current and Voltage measurementsMultiMeter functions include AC/DC Voltage, Resistance,

Capacitance, Frequency, Diode, and Continuity 1.7" (43mm) jaw opening 4000 count backlit display Features include Data Hold and Min/Max Autoranging with manual range button Auto Power offWith test leads, 9V battery,

Type K probe (EX82030)

MPN # Description EX820 Clamp MeterEX830 Clamp MeterEX840 Clamp Meter

EX820 EX830 EX840AC Current AC/DC Current AC/DC VoltageTrue RMS True RMS Resistance

Type K Temp. Type K Temp. CapacitanceCATIII-600V DC Zero Frequency

CATIII-600V Diode, Inrush &Continity

CATIV-600V

400A Dual Input Clamp Meters + IR Thermometer + NCV True RMS measurements for accurate AC Voltage and

Current measurements Dual type K thermocouple input with Differential

Temperature function (T1, T2, T1-T2) Built-in non-contact Voltage detector with LED alert Built-in non-contact IR Thermometer with laser pointer

for locating hot spots 8 to 1 distance to target ratio DC Current function ideal for automotive, heavy

equipment and marine applicationsWith test leads,

two Type K bead wire probes, batteries & case

MPN # Description MA250 Clamp Meter + NCVMA410 Clamp Meter + NCVMA620 Clamp Meter + NCVMA640 Clamp Meter + NCV

MPN # DescriptionEX623 Clamp Meter + IR + NCV

MA250 MA410 MA620 MA64020-200A 40-400A 60-600A 60-600A

2000 Count 4000 Count 6000 Count 6000 CountDC Zero MIN/MAX MIN/MAX

DC Current

400A AC/DC Clamp Meter 4000 Count backlight displayWith AC/DC Current and Voltage, Resistance, Frequency,

Capacitance Temperature, Diode and Continuity 0.9” (23mm) jaw opening Auto power off Data Hold “freezes” data in displayWith test leads, case

& two AAA batteries

Meters

MPN # Description MN26T Multimeter

MPN # Description CT70 Circuit Load Tester

CT70 AC Circuit Load TesterQuickly checks for AC outlet load handlingcapabilities plus Outlet Tester functions Large LCD display with color pass/fail test alerts Selectable loads of 12, 15 & 20A Neutral to Ground Voltage Impedance Complete with AC test cord

MPN # Description VT10 Multifunction Voltage TesterVT30 Digital Voltage Tester

Voltage TestersVoltage, Continuity and Phase Tester with Flashlight with double molded IP64 housing Backlit LCD digital display with bargraph AC/DC voltage

indication (VT30): 6, 12, 24, 50, 230, 400 & 690V LED AC/DC voltage indication (VT10):

AC: 24, 48, 120, 208, 240, 277, 480 & 600V. DC: 6,12, 24, 36, 48, 110, 220 & 400V Polarity detection with LEDs for positive and negative DC Continuity Test with audible tone (VT30) Two handed operation for low impedance testingWith batteries,

protective cap & pouch case

Phone 1 866 663 8233

Digital IR Thermometer Temperature Range: -27° to 428°F Accuracy: ±2% of reading or ±2°C 0.1° resolution for accurate readings Selectable temperature units F/C Emissivity preset to 0.95 LCD display Non-contact Does not use a laser beamMetal alloy case Low battery indication Automatic power

OFF after 15 secs.

Meters

14

Type 2 Sound Level MeterTwo range meter with backlitLCD display High accuracy meets ANSI and

IEC 651 Type 2 standards High and Low measuring

ranges (35 to 130dB) Data Hold and Max Hold

functions Backlit display ideal in the dark Complete with microphone

wind screen and 9V battery

Digital Sound Level MeterAnalog bargraph with 50dBrange updates every 40ms ±2dB accuracy with 0.1dB

resolution AC analog output Record Max/Min values

over time 40 to 130dB measuring range

LCR MeterMeasures capacitance,inductance and resistance Primary and secondary

count displays Test frequencies 120Hz

and 1kHz Complete with clips, leads,

battery and holster

Mini Laser PhotoTachometer CounterUsed for greater accuracy and longer measuring distances taking non-contact RPM measurements.Memory button holds last reading

and recalls min/max readings Easy to read large

5 digit LCD display 2 to 99,999 rpm range

MPN # Description MO280 Moisture Meter

Psychrometer Humidity: 0 to 100%RH Temperature (internal): (-30 to 100°C) Dual backlit display Simultaneous display:

Humidity/Temp., Humidity/Dew Point, Humidity/Wet Bulb Data Hold & Min/Max functions Auto power off with disable

and low battery indicatorWith case and 9V battery

MPN # Description 407730 Sound Meter

MPN # Description RH390 Psychrometer

UT55 DigitalMultimeter Special functions

include transistor & diode test, continuitybuzzer, sleep mode,low battery display & input impedance Includes test lead,

battery, manual, probe & holster

MPN # Description UT203 Clamp Meter

MPN # Description UT55 UT55 Multimeter

UT203 Clamp Multimeter Measures ACDC voltage and current with frequency & auto ranging capabilities in a compact design Special functions

include diode test, sleep mode, continuity buzzer & data holdWith test lead,

manual & bag

MPN # Description UT33C UT33C Multimeter

UT33C Pocket-SizeDigital Multimeter Power: 9V Battery Features diode voltage,

temperature, continuitybuzzer, data hold, lowbattery display andbacklight display Accessories supplied:

Test lead, battery,manual, holster andtemperature probe

MPN # Description UT58C UT58C Multimeter

UT58C Digital Multimeter Power: 9V Battery Features diode voltage,

temperature, frequency,continuity buzzer, data hold and low battery displayWith test lead,

battery, manual, multi-purpose socket & holster& temperature probe

MPN # Description UT20B UT20B Multimeter

Pocket-Size Digital Multimeter Power: 12V Battery Features 1.5V &

9V battety test, diode voltage, square wave output and low battery displayWith test lead,

battery and manual

MPN # Description DIT-205 IR Thermometer

MPN # Description 407732 Sound Meter

Test & Measurement

Pinless Moisture MeterMonitor moisture in woodand other building materials Non-invasive measurement

with virtually no surfacedamageMeasurement depth to

0.75" below surface Electro-magnetic testing 0 - 99% range limit by

wood type

MPN # Description 380193 LCR Meter

MPN # Description 461920 Tachometer

Phone 1 866 663 8233

15


MPN # Description MT-1503 Multimeter

3 3/4 Smart Multimeter Intelligent one touch power button with

three optional function keys 3 ¾ digits, 4000 counts, updates 3/sec. One handed operation Ergonomic design with rugged

constructionWith test leads & battery

MPN # DescriptionMT-4011 Thermomter

K Type Digital Thermometer Large LCD 18.2mm display T1, T2 or T1-T2 channel display 10 set data memory function °C & °F selection, Max/Min reading,

data hold, relative reference,memory, limit, Hi/Lo


Protective Function Analog Multimeter Resistance, Current & Voltage 10 Amp DC Range, Transistor hFE Test Continuity Buzzer and Battery Test Zero-center meter (Null) Test leads, batteries & fuse


Protective Function Analog Multimeter Resistance, Current,

Voltage & Capacitance Transistor hFE and Battery Test Test leads, batteries & fuse

MPN # Description NT-311 Temp/HumidityNT-312 w/Probe

Digital Temperature Humidity MetersMAX. and MIN. temperature and

humidity memory function °C / °F switch. 12-hour/24-hour displaying system

selection. Wall hanging or desk-top stand supportNT312: with probe

Light Intensity Meter Comply with CE safety standards Portability and simplicity one-hand operation Display: 6 digits LCD display. Hold, auto power off, low battery indication,

Max/Min mode. Light intensity range: 0~90000Lux,

0~8300ftcApplications: Indoor, Office environment, Labs, Environment studies

Sound Level Meter Comply with CE safety standards Software calibrating to insure high reliability Display: 4 digits LCD display.Measuring level range from 30~120dB,

Frequency range 31.5Hz~8KHz Dual display with analog bar graph Auto / Manual mode Sound Over and under indicator

MPN # Description MT-4017 Light Intensity Meter

MPN # Description MT-4018 Sound Level Meter

Phone 1 866 663 8233


16

MPN # Description MTP 2850 Multimeter

Electronic Multimeter 3999 counts large

LCD display True RMS RS-232 pc interface Temperature,

capacitance, frequency and duty cycle measurements

Includes 9V battery, test leads, temperature probe, RS-232 serial cable, PC software DC-R, & carrying case


IndustrialMultimeter True RMS AC voltage

and current readingsMin/max recording Peak recording as well

as frequency andcapacitance ranges Full range protectionWater proofIncludes 9V battery &test leads


All-in-1 MultimeterMeasures AC/DC voltage,

AC/DC current, resistance,capacitance, inductanceand frequency Audible and visual

indications Over-molding

rubber case Ergonomic designIncludes test leads,temperature probe MS-3400

MPN # Description MS-5300 LCR Multimeter

LCR Multimeter Over molding rubber

case protects the meter RS-232 interface Resistance,

capacitance,inductance, auto andmanual range, dataholdMin/Max value

measurement Auto power off/disable

auto power offIncludes 3.6V battery, testleads & software

Pocket Sound Level Meter Ranges from 40dB to 130dB

at frequencies between 31.5Hz and 8KHz 4 digit LCD display Display resolution 0.1dBWith one equivalent weighted

sound pressure level AIncludes 9V battery

MPN # Description MTP I410 Clamp-on AdaptorMTP I1010 Clamp-on Adaptor

AC/DC Clamp-on Adaptors 400A (MTP IC410) 1000A (MTP IC1010) Clamp jaw opening 1.2’’ Non contact voltage detector

50-600VAC (MTP IC410) Perfect for low current

applications (MTP IC410) Includes test leads, 9V battery Includes carrying case (MTP

IC1010)

Pocket Light Meter 3 ½ digit LCD display with LUX,

Fc, Lo Bat, max indicationMeasures from 0 to 40,000

Lux/Fc in four ranges withresolution 0.1Lux/FCMeasuring rate is 2.5 times

per second Auto ranging, max hold,

auto power off Light sensitive backlight LCDIncludes 9V battery

MPN # Description MTP 3093 AC Clamp MeterMTP 3094 AC/DC Clamp Meter

Clamp Meters 400A AC (#3093),

400A AC/DC (#3094) Clamp opening 1.2’’ 4000 count digital

LCD display Data hold, REL (zero)

function Auto power offIncludes test leads,carrying case, alligatorclips, temperatureprobe & AAA batteries

MPN # Description MTP 3095 AC Clamp MeterMTP 3096 AC/DC Clamp Meter

Clamp Meters AC True RMS 1000A AC (#3095),

1000A AC/DC (#3096) Clamp opening 1.5’’Max/Min, data hold,

REL (zero) function 6000 count digital LCD

display with backlight Analog bargraph (61 seg.)Includes test leads,carrying case, alligatorclips, temperature probe & 9V battery

MPN # Description MTP 1013 Sound Meter

MPN # Description MTP 1014 Light Meter

MPN # Description MTP 1015 IR Pocket Thermometer

Pocket InfraredThermometer °C/°F Selectable 6 : 1 distance target ratio Temperature range:

-30 to 270°C Single laser pointer 0.95 fixed emissivity Includes 9V battery

Phone 1 866 663 8233

17


Energy Monitoring SystemMeasures & Displays : Instant Energy (kw),

Energy Consumption (kwh), Total Cost ($ value),Pollution (Kg CO2), Averages Tariff Rates : Set up

to three tariffs for specific peak times History: Retrieve past

history viewable by day, week or month Transmitter: works on

a Single to Three phase system Alarm Setting Software

MPN # Description MTP 3100 Power Saver

50 Series II Thermometers For fast response and laboratory accuracy (0.05% + 0.3°C)Measures J, K, T & E type thermocouples R, S & N also read by 53-2 and 54-2 Relative time clock on MIN, MAX, and AVG provides a

time reference for major events 53-2/54-2 offer data logging of up to 500 points of

data, and a built-in infrared PC interfaceMPN # Description 51-2 Single Output Thermometer52-2 Dual Output Thermometer53-2-B Datalogging Single Output Thermometer54-2-B Datalogging Dual Output Thermometer54-2-B

62MAX Thermometers The new Fluke 62MAX infrared thermometers aresmall in size, extremely accurate and very easy to use.IP54 rated for dust and water resistance. Precise yetrugged enough to take a 3-meter drop, they're the onlyIR thermometers around you can handle without care!62MAX+ features dual rotating lasers to help identifythe measured area.MPN # Description 62MAX 62MAX Thermometer62MAX+ 62MAX Thermometer

MPN # Description MTP 1325 ThermometerMTP 1329 Thermometer

Infrared Thermometers °C/°F Selectable

12 : 1 distance target ratio Temperature range : -50 to 450°C (MTP 1325)

-50 to 550°C (MTP 1329) Single (MTP 1325) & dual (MTP 1329) laser pointer

0.95 fixed emissivity (MTP 1325) Adjustable emissivity 0.10 to 1.0 (MTP 1329)

Includes 9V battery Includes carrying case

42500 IR Thermometer Range: -4 to 500°F (-20 to 260°C) Auto power off Built-in laser pointer identifies target area Backlighting illuminates display Automatic Data Hold when trigger released 6:1 distance to target ratio Fixed 0.95 emissivity covers 90% of surface

applications Includes 9V battery and case

MPN # Description 42545 Thermometer

MPN # Description 42510A Thermometer



42509 IR Thermometer w/Color Alert Dual lasers identify distance and location

where accuracy is highest 12" distance model Fast response is ideal for quick checks of

multiple spots in a process or for catching spikes in temperatureMeasures up to 950°F (510°C) Blue backlit dual LCD display changes to

Red backlit when reading exceeds High or Low set points Exclusive 150 millisecond response

42545 IR Thermometer Range: -58 to 1832°F (-50 to 1000°C) Built-in laser pointer High and low alarmsMAX, MIN, DIF & AVG recording Backlighting illuminates display High resolution of 0.1° up 199.9° Automatic Data Hold Adjustable emissivity Auto power off High 50 to 1 distance to target ratio measures

smaller surface areas at greater distances Includes 9V battery and case

42510A IR Thermometer Range: -58 to 1200°F (-50 to 650°C) Auto power off Built-in laser pointer 12:1 distance to target ratio Adjustable High/Low setpoints with audible

alarm alerts Backlighting illuminates display High resolution of 0.1° to 199.9° Data Hold and Min/Max Includes 9V battery and case

Phone 1 866 663 8233

Meters

18

Test & Measurement

PC Based Digital Storage Oscilloscopes A compact Digital Storage Oscilloscope (DSO) thatinterfaces with your PC. Simply plug this portableunit into the USB port in your PC or laptop andtransform your computer into a fully functionaldual trace 40, 60 or 100MHz DSO. Supports Windows2000/XP/Vista 100, 150 or 250MS/s sampling rate USB2.0 connectivity External trigger input

Humidity & Temperature Chart Recorder Simultaneous numerical and graphical display of Humidity and

Temperature readings, plus Time and DateMeasures Humidity (10 to 95%RH) and Temperature (-20.0°F to

140.0°F) plus calculates Dew Point Internal memory records up to 49,000 data points and can be transferred

to a PC via RS-232 serial port for further data analysis Audible and visual

alarm with Hi/Lowsetpoints Download, analyze,

and store data usingWindows ®95/98/2000/NT/ME/XP CompatibleSoftware (included) Complete with built-in

stand, detachableprobe with 3ft (1m) cable,RS232 cable,software, 110VACadaptor and 3 AAbatteries

MPN # Description RH520A Recorder

MPN # Description IR201 IR Thermometer

Pocket IR ThermometerHandy troubleshooting thermometerwith laser pointer measures to518°F (270°C) Economical small pocket size

design for convenience Built-in laser pointer identifies

target area Data Hold and Max Hold Fixed emissivity covers 90% of

surface applications Auto power off

445703

445702

Hygro-Thermometer Display relative humidity and temperature °C or °F simultaneouslyMax/Min memory of both % RH and temperature with reset function

MPN # Description 445702 Thermometer/Clock445703 Thermometer

3 1/2 MultimeterDMM with automatic polarityfunction and 3 1/2 digit LCD displayMeasurements: DC current up to

10A, DC voltage up to 600V, andresistance up to 2MΩ Diode, transistor and continuity test

with buzzer Data-hold function and backlight

MPN # Description DVM810 Multimeter

MPN # Description DVM850BL Multimeter

Mini 3 1/2 Digit DMM - 19 Ranges Automatic polarity indication Voltage: AC 500V and DC 500V max. Current measurements: DC 10A max. Resistance measurements: 2Mohm Diode and transistor (hFE) test Includes overrange, continuity buzzer,

transistor test, diode test, low-battery indication, manual ranging mode LCD display size: 0.5"

MPN # Description DS0-3100 40 MHz Digital Storage OscilloscopeDSO-3150 60MHz Digital Storage OscilloscopeDSO-3250 100MHz Digital Storage Oscilloscope

MPN # Description PCSGU250 USP-PC Scope + Generator

USB-PC Scope + Generator Feature-packed PcLab2000-LT software for

two channel oscilloscope, spectrumanalyser, recorder, function generator andbode plotter.With the generator, you can create your own

waveforms using the integrated signal waveeditor. For automated measurements, it iseven possible to generate wave sequences,using file or computer RS232 input.

Phone 1 866 663 8233

19


MPN # Description HPS50 Scope

Personal Scope with USB 40MHz sampling rate, 12MHz analog

bandwidth, 0.1mV sensitivity X and Y position signal shift DVM readout LCD backlight, 4 different screen modes Adjustable trigger level 5mV to 20V/div in 12 steps USB PC Connection real-time and

screen captureIncludes: worldwide charging adaptor, insulated measurement probe x1 / x10: PROBE60S and USB cable

Personal Scope 10MS/sA portable oscilloscope at the size and the cost of a good multimeter idealfor hobby, service, automotive and development. Up to 2MHz analogue bandwidth 10MHz sampling rate 5mV to 20V/div in 12 steps 200ns to 1hour/div time base in 32 steps Trigger mode: run, normal, once, roll, slope +/- X and Y position signal shiftWith battery charging circuit & power supplyHPS10SE includes blue LCD, white backlight, and a carry case

HPS140 Handheld Pocket Scope 40MS/s Bandwidth: up to 10 MHz (-3dB or -4dB at selected ranges) Input range: 1mV to 20V/division in 14 steps Input coupling: DC, AC and GND Real-time sample rate up to 40MS/s AD resolution: 8 bits Time base: 250ns to 1h per division Auto set-up function (or manual) Probe x10 readout option Readouts: DC, AC+DC,True RMS,

dBm, Vpp, Min-Max. (±2.5%) Audio power measurement

from 2-32 ohms Hold & store function Time and Voltage markers readoutMax. 100Vp AC+DCWhite LED backlight Operates on NiMH rechargeable

battery pack (included) Operates up to 6 hours

on one chargeMPN # Description HPS140i Pocket Scope

HPG1 Handheld Function Generator 1MHzA complete function generator in pocket format! Now you can take testsignals on the move, 3 waveforms can be selected. Set the output voltageor frequency and select signal waveform using the on screen menu. Apowerful sweep function is also included. Frequency range: from 1Hz to 1,000,000Hz (± 0.01%) Frequency steps: 1Hz, 10Hz, 100Hz, 1kHz and 10kHzWaveforms: sine, square and triangle Sweep function with bi-direction option Output voltage: max. 8Vpp Real output level measurement:

dBm / Vrms or Vpp readout (±3%) Typical sine wave distortion (THD):

< 0.1% @ 0dB / 600 ohms Square wave rise/fall time: typ. 0.2µs Output impedance: 50 ohmsIncludes: handheld pocket generator, manual, BNC adapter, BNC male to RCA female, BNC male to 2x 4mm banana plug & USB power supply adaptor.MPN # Description HPG1 Pocket Function Generator

CircuitGear 20 MS/sec, dual channel scope Digital readouts, variable persistence Pre-Trigger View, data capture 2 MHz arbitrary waveform generator 0.1 Hz frequency resolution Vector network analyser, 0.1Hz to 2MHzWindows, Mac, Linux host O/S

Advanced Waveform Generator Standard and Arbitrary Waveforms 0.03 Hz to 10 MHz sine, 3MHz other Free-running, triggered, tone burst Hardware noise source 2 PWM outputs, 0 to 100kHz +/-10V output, 150 ohmWindows, Mac, Linux host O/S

MPN # Description CGR-101 CircuitGear

PC Based Logic Analyzers These PC based Logic Analyzers have patented waveform compressiontechnology that can increase the effective memory capacity beyond thephysical bits per channel. Maximum Power Dissipation 2W Data can be processed to

CSV or TXT files Flexible signal trigger options Binary/Decimal/Hex display formats Threshold Voltage: range -6V to +6VMaximum input voltage:

-30V to +30V I2C, SPI, UART (RS232 & RS485) &

7-Segment decoder plug-ins includedWindows 2000/XP/Vista/7

MPN # Description LAP-C16032 PC Based Logic Analyzer -16 Channels, 32KLAP-C16128 PC Based Logic Analyzer - 16 Channels, 128KLAP-C162000 PC Based Logic Analyzer - 16 Channels, 2MLAP-C32128 PC Based Logic Analyzer - 32 Channels, 128KLAP-C322000 PC Based Logic Analyzer - 32 Channels, 2MLAP-CLIPS Test clips, 36/package

MPN # Description HPS10 ScopeHPS10SE Scope

MPN # Description WGM-201 Advanced Waveform Generator

Phone 1 866 663 8233

Oscilloscopes

20

Test & Measurement

InfiniiVision X-Series OscilloscopesOscilloscopes redefined: Breakthrough technology delivers more scope for the same budgetSEE more of your signal more of the time with the biggest screen in its class, the deepest memory and the fastest waveform update ratesDO more with the power of up to 5 instruments in 1: oscilloscope, logictiming analyzer (optional), protocol analyzer (optional), WaveGen built-infunction and arbitary waveform generator (optional) & built-in 3-digit voltmeterGET more investment protection with the industry's only fully-upgradablescope, including bandwidth

Industry exclusives in this scope class Only integrated low-cost MSO Only integrated function and

arbitary waveform generator Biggest display Only completely upgradable oscilloscope

MPN # Description DSOX2002A 70 MHz, 2 channels OscilloscopeMSOX2002A 70 MHz, 2 channels, 8 digital channels OscilloscopeDSOX2004A 70 MHz, 4 channels OscilloscopeMSOX2004A 70 MHz, 4 channels, 8 digital channels OscilloscopeDSOX2012A 100 MHz, 2 channels OscilloscopeMSOX2012A 100 MHz, 2 channels, 8 digital channels OscilloscopeDSOX2014A 100 MHz, 4 channels OscilloscopeMSOX2014A 100 MHz, 4 channels, 8 digital channel OscilloscopeDSOX2022A 200 MHz, 2 channels OscilloscopeMSOX2022A 200 MHz, 2 channels, 8 digital channels OscilloscopeDSOX2024A 200 MHz, 4 channels OscilloscopeMSOX2024A 200 MHz, 4 channels, 8 digital channels Oscilloscope

ACCESSORIES FOR INFINIIVISION X-SERIESMPN # Description DSOXLAN LAN/VGA connection moduleDSOXGPIB GPIB connection moduleN6456A Rack mount kitN6457A Soft carrying case and front cover panelN6458A Hard copy manual

2000 X-Series

3000 X-Series3000 X-SeriesOscilloscopesAdvanced technology gives you 5 instruments in 1 box for thesame price

100 MHz to 1 GHz bandwidth, both DSO and MSO models

Hardware-based measurement applications including serial decode Only 20-MHz built-in WaveGen function/arbitary waveform generator Only integrated digital voltmeter 8.5-inch WVGA display offers 50% larger and 3x the resolution of

competitive scopes Up to 1,000,000 waveform updates/second Fully upgradable: bandwidth, MSO, memory, measurement & WaveGen

2000 X-SeriesOscilloscopesExpand your capabilities even ifyou can't expand your budget

70 to 200 MHz bandwidth, both DSO and MSO models

Only economy-class scopes with mixed signal capability

Only 20 MHz built-in WaveGen function generator Only integrated digital voltmeter 8.5-inch WVGA display offers 2x the viewing area

and 5x the resolution of competitive scopes Up to 50,000 waveform updates/second Fully upgradable: bandwidth, MSO, memory, measurement & WaveGen

MPN # Description DSOX3012A 100 MHz, 2 channels OscilloscopeMSOX3012A 100 MHz, 2 channels, 16 digital channels OscilloscopeDSOX3014A 100 MHz, 4 channels OscilloscopeMSOX3014A 100 MHz, 4 channels, 16 digital channels OscilloscopeDSOX3024A 200 MHz, 4 channels OscilloscopeMSOX3024A 200 MHz, 4 channels, 16 digital channels OscilloscopeDSOX3032A 350 MHz, 2 channels OscilloscopeMSOX3032A 350 MHz, 2 channels, 16 digital channel OscilloscopeDSOX3034A 350 MHz, 4 channels OscilloscopeMSOX3034A 350 MHz, 4 channels, 16 digital channels OscilloscopeDSOX3052A 500 MHz, 2 channels OscilloscopeMSOX3052A 500 MHz, 2 channels, 16 digital channels OscilloscopeDSOX3054A 500 MHz, 4 channels OscilloscopeMSOX3054A 500 MHz, 4 channels, 16 digital channels OscilloscopeDSOX3102A 1 GHz, 2 channels OscilloscopeMSOX3102A 1 GHz, 2 channels, 16 digital channels OscilloscopeDSOX3104A 1 GHz, 4 channels OscilloscopeMSOX3104A 1 GHz, 4 channels, 16 digital channels Oscilloscope

UPGRADE KITS FOR INFINIIVISION X-SERIESMPN # Description DSOX2BW12 Upgrade 70 MHz to 100 MHz on 2000 X-Series 2 channel models DSOX2BW14 Upgrade 70 MHz to 100 MHz on 2000 X-Series 4 channel models DSOX2BW22 Upgrade 100 MHz to 200 MHz on 2000 X-Series 2 channel models DSOX2BW24 Upgrade 100 MHz to 200 MHz on 2000 X-Series 4 channel models DSOX3BW32 Upgrade 100 MHz to 350 MHz on 3000 X-Series 2 channel models DSOX3BW52 Upgrade 350 MHz to 500 MHz on 3000 X-Series 2 channel models DSOX3BW24 Upgrade 100 MHz to 200 MHz on 3000 X-Series 4 channel models DSOX3BW34 Upgrade 200 MHz to 350 MHz on 3000 X-Series 4 channel models DSOX3BW54 Upgrade 350 MHz to 500 MHz on 3000 X-Series 4 channel modelsDSOX2MSO Add 8 digital channels to your 2000 X-Series oscilloscopeDSOX3MSO Add 16 digital channels to your 3000 X-Series oscilloscope

APPLICATION OPTIONS FOR INFINIIVISION X-SERIESMPN # Description DSOX2MASK Mask/waveform limit testing (for 2000 X-Series)DSOX3MASK Mask/waveform limit testing (for 3000 X-Series)DSOX2SGM Segmented memory (for 2000 X-Series)DSOX3SGM Segmented memory (for 3000 X-SeriesDSOX2WAVEGEN WaveGen function generator (for 2000 X-Series)DSOX3WAVEGEN WaveGen function generator (for 3000 X-Series)DOXEDK Education training kit (for 2000 and 3000 X-Series)DSOX3EMBD I2C/SPI trigger and decode (for 3000 X-Series)DSOX3COMP RS-232/UART trigger and decode (for 3000 X-Series)DSOX3AUTO CAN/LIN trigger and decode (for 3000 X-Series)DSOX3AUDIO I2S trigger and decode (for 3000 X-Series)DSOXDVM Integrated 3-digit voltmeter (for 2000 and 3000 X-Series)DSOX3AERO MIL-STD 1553/ARINC 429 trigger and decode (for 3000 X-Series)DSOX3FLEX FlexRay trigger and decode (for 3000 X-Series)DSOX3PWR Power measurement (for 3000 X-Series)DSOX3ADVMATH Advanced math (for 3000 X-Series)DSOX3VID HDTV video triggering (for 3000 X-Series)

Phone 1 866 663 8233

21

Test & Measurement Oscilloscopes

What is unique about Agilent’s batterypowered oscilloscope? Agilent’s 6000A Series with the batteryoption is the only battery powered mixedsignal oscilloscope (MSO), highestperformance 100MHz -500MHz batterypowered oscilloscope and only 1GHz batterypowered oscilloscope available in the market.

DSO6012

MPN # Description DSO6012A 100 MHz, 2 channels OscilloscopeMSO6012A 100 MHz, 2 scope and 16 digital channels OscilloscopeDSO6014A 100 MHz, 4 channels OscilloscopeMSO6014A 100 MHz, 4 scope and 16 digital channels OscilloscopeDSO6032A 300 MHz, 2 channels OscilloscopeMSO6032A 300 MHz, 2 scope and 16 digital channels OscilloscopeDSO6034A 300 MHz, 4 channels OscilloscopeMSO6034A 300 MHz, 4 scope and 16 digital channels OscilloscopeDSO6052A 500 MHz, 2 channels OscilloscopeMSO6052A 500 MHz, 2 scope and 16 digital channels OscilloscopeDSO6054A 500 MHz, 4 channels OscilloscopeMSO6054A 500 MHz, 4 scope and 16 digital channels OscilloscopeDSO6102A 1 GHz, 2 channels OscilloscopeMSO6102A 1 GHz, 2 scope and 16 digital channels OscilloscopeDSO6104A 1 GHz, 4 channels OscilloscopeMSO6104A 1 GHz, 4 scope and 16 digital channels Oscilloscope

InfiniiVision 6000 Series OscilloscopesEngineered for the best signal visibilityThe 6000 Series provides the performance and problem-solving tools thatyou need to gain superior insight into the testing and troubleshooting ofmixed-signal designs in a single instrument. Includes: (4) passive probes.

Specifications: Bandwidth: 100 MHz to 1 GHz BW Channels: 2 or 4 analog and 16 digitalMemory: 8 Mpts standard Sample rate: up to 4 GSa/sAttractive Ultra-responsive, high resolution color LCD with 256 intensity levels Stackable form factor with built-in storage Battery power option available 1U high 6000L series availableFast Fast update rate to 100,000 waveforms per secondMegaZoom III technology - always fast, always responsive, always onSmart Serial decode and trigger for I2C/SPI, RS-232/UART, CAN/LIN, FlexRay,

I2S, MIL-STD 1533 Rapid core-assisted debug of Xilinx or Altera FPGAs Segmented memory Offline PC viewing RF contextual viewing

VSA softwareMask testing Power measurement and analysis Secure environment

InfiniiVision 7000B Series OscilloscopesEngineered for the best signal visibility

See more analog,digital and serial

signals better with justone instrument.

Powered byMegaZoom III

technology thatdelivers a responsivedeep memory, high-

definition displaysystem and a superior

ability to capturetransient signals.

All models come with a standard 3-year warranty. Specifications Bandwidth: 100 MHz to 1 GHz Channels: 2 or 4 analog and 16 digital Sample rate: up to 4 GSa/s Memory: 8 Mpts standardAttractive Industry's largest, high-resolution 12.1" color LCD display Easy-to-operate front-panel controls with pushable knobs Small foot-print form factor with stable tilt designFast Fast update rate to 100,000 waveforms per second MegaZoom III technology - always fast, always responsive, always onSmart Serial decode and trigger for I2C/SPI, RS-232/UART, CAN/LIN, FlexRay,

I2S, MIL-STD 1533 Rapid core-assisted debug of Xilinx or Altera FPGAs Segmented memory Offline PC viewing RF contextual viewing VSA software Mask testing Power measurement and analysis Secure environment

UPGRADE KITS FOR 7000B SERIESMPN # Description N2741A-002 DSO7012B to MSO7012B upgradeN2741A-004 DSO7014B to MSO7014B upgradeN2735A-002 DSO7032B to MSO7032B upgradeN2735A-004 DSO7034B to MSO7034B upgradeN2737A DSO7104B to MSO7104B upgradeN2736A-002 DSO7052B to MSO7052B upgradeN2736A-004 DSO7054B to MSO7054B upgrade

MPN # Description DSO7012B 100MHz, 2 channel OscilloscopeMSO7012B 100MHz, 2 scope and 16 digital channels OscilloscopeDSO7014B 100MHz, 4 channel OscilloscopeMSO7014B 100MHz, 4 scope and 16 digital channels OscilloscopeDSO7032B 350MHz, 2 channel OscilloscopeMSO7032B 350MHz, 2 scope and 16 digital channels OscilloscopeDSO7034B 350MHz, 4 channel OscilloscopeMSO7034B 350MHz, 4 scope and 16 digital channels OscilloscopeDSO7052B 500MHz, 2 channel OscilloscopeMSO7052B 500MHz, 2 scope and 16 digital channels OscilloscopeDSO7054B 500MHz, 4 channel OscilloscopeMSO7054B 500MHz, 4 scope and 16 digital channels OscilloscopeDSO7104B 1GHz, 4 channel OscilloscopeMSO7104B 1GHz, 4 scope and 16 digital channels Oscilloscope

Phone 1 866 663 8233

MPN # Description DSO1052B 50 MHz, 2 channels OscilloscopeDSO1072B 70 MHz, 2 channels OscilloscopeDSO1102B 100 MHz, 2 channels OscilloscopeDSO1152B 150 MHz, 2 channels OscilloscopeDSO1004A 60 MHz, 4 channels OscilloscopeDSO1022A 200 MHz, 2 channels OscilloscopeDSO1014A 100 MHz, 4 channels OscilloscopeDSO1024A 200 MHz, 4 channels Oscilloscope

ACCESSORIES FOR 1000 SERIESMPN # Description N2738A Soft Carrying CaseN2739A Rackmount Kit

RECOMMENDED PROBES FOR 1000 SERIESMPN # Description N2862B 150 MHz, 10:1 passive probe

(standard with 50 MHz to 100 MHz models)N2863B 300 MHz, 10:1 passive probe

(standard with 150 MHz and 200 MHz models)10070D 1:1, 20 MHz passive probe10076B 100:1, 4 kV, 250 MHz high voltage passive probeN2791A 25 MHz, 700 V differential probe1146A 100 kHz current probe, AC/DCN2771B 1000:1, 30 kV, 50 MHz high voltage passive probeN2891A 70 MHz, 7 kV differential probe

22

Test & MeasurementOscilloscopes

1000A/B Series Portable OscilloscopesEngineered to give you more scope than you thought you could affordAgilent’s 1000A/B Series oscilloscopes deliver the performance andfeatures you expect in a big scope – and the portability and low price yourequire in a small one.

Powerful signal capture and display: Wide viewing angle, bright color display Up to 20 kpts memory, up to 8x more than other scopes Up to 2 GSa/s sample rate Simultaneous viewing of main and zoomed waveforms 25% more viewing area with menus switched off

Advanced measurement capability: 23 automatic measurementsWaveform math including FFT Standard go/no-go mask testing Sequential acquisition of up to 1000 trigger events Selectable high pass, low pass, band pass, and band reject digital filters

Accelerated productivity: Autoscale 11-lanuguage (including French) localization of

user interface, front panel controls ßand manuals USB connectivity Free education student lab guide and professor slide set

Weighing less than 7 pounds with a small footprint, the 1000 Series cango anywhere with ease.

Whether your job is designing products in R&D, teaching the nextgeneration in education, or testing in manufacturing or service, the new 1000 Series oscilloscopes can help get it done with confidence. R&D: Features normally only found on much higher priced scopes

equip the 1000 Series to be a powerful choice for R&D applications. Education: Economical prices make the 1000 Series ideal for teaching

basic scientific and engineering measurements at lab stations in schools and universities.Manufacturing: Standard go/no-go mask testing is just one of the reasons

manufacturing and service test demand 1000 Series solutions.

1000A Specifications: Bandwidth: 60, 100, 200MHz Channels: 2 / 4 analog channels Sample rate: 2 GSa/s Memory: 20 kpts Display: 5.7” colour

NEW 1000B Specifications: Bandwidth: 50, 70, 100, 150MHz Channels: 2 analog channels Sample rate: 1 GSa/s Memory: 16 kpts Display: 5.7” colour, QVGA

DSO1024A

DSO1052B

Phone 1 866 663 8233

23

Test & Measurement Oscilloscopes Probes

Oscilloscopes ProbesWhether you need the high bandwidth and low loading of an active probe, an easy way to connect to ICs, or a probe to measure high voltages, there's a wide selection of high-performance accessories for your Agilent oscilloscope. Use Select & Compare to shop by scope, specification or price. There are a number of different types of oscilloscope probes to choose from and each has an area where it best performs. Voltage probes are classified as either passive and active probes. Current probes are also available to generate a voltage output proportional to an input current in the user’s circuit. Passive Probes: The most widely used type of oscilloscope probe is the “passive probe”.

Passive probes are also the most rugged and economical of probes. More information Single-ended Active Probes have the best overall combination of resistive and capacitive loading. With

such low loading, active probes can be used on high-impedance, high-frequency circuits that would be seriously loaded by passive probes. Moreinformation Differential Active Probes are used to look at signals that are referenced to each other instead of earth ground and to look at small signals in the presence

of large DC offsets or other common mode signals such as power line noise. More information Current Probes sense the current flowing through a conductor and convert it to a voltage that can be viewed and measured on an oscilloscope

MPN # Bandwidth Attenuation Input Dynamic Compatible OscilloscopesRatio Impedance Range 2000 X- Series 3000 X- Series 6000 Series 7000 Series

Passive Probe10070D 20 MHz 1:1 1 MΩ, 70 pF 400 Vpk

10073D 500 MHz 10:1 1 MΩ, 50 pF 400 Vpk 300 MHz - 1 GHz

10074D 150 MHz 10:1 1 MΩ, 15 pF 400 Vpk

N2862B 150 MHz 10:1 1 MΩ, 30 pF 300 Vrms

N2863B 300 MHz 10:1 1 MΩ, 30 pF 300 Vrms

N2889A 350 MHz 10:1/1:1 10 MΩ,11 pF 300Vrms 300 MHz - 1 GHz

N2890A 500 MHz 10:1 10 MΩ,11 pF 300Vrms 300 MHz - 1 GHz

Miniature Passive ProbeN2870A 35 MHz 1:1 1 MΩ 55 V CAT II

N2871A 200 MHz 10:1 1 MΩ, 9.5 pF 300 V CAT II

N2873A 500 MHz 10:1 1 MΩ, 9.5 pF 300 V CAT II

N2874A 1.5 GHz 10:1 500 Ω, 1.8 pF 8.5 V CAT I

InfiniiMax Differential and Single-Ended Probe (requires one or more InfiniiMax probe heads)1130A 1.5 GHz 10:1 50 kΩ ± 2.5V 300 MHz - 1 GHzHigh-Voltage Differential Probe1141A 200 MHz 1:1 1 MΩ, 7 pF 200 V (dc + peak ac) 300 MHz - 1 GHz

N2791A 25 MHz 10:1/100:1 8 MΩ, 8 pF ±700V

N2891A 70 MHz 100:1/1000:1 100 MΩ, 5 pF ±7000V

N2790A 100 MHz 50:1/500:1 8 MΩ, 3.5 pF ±1.4kV 300 MHz - 1 GHz

N2792A 200 MHz 10:1 1 MΩ, 3.5 pF ±20V

N2793A 800 MHz 10:1 200 kΩ, 1 pF ±15V

Single-Ended Active ProbeN2795A 1 GHz 10:1 1 MΩ,1 pF 0 to ±8V 300 MHz - 1 GHz

N2796A 2 GHz 10:1 1 MΩ,1 pF 0 to ±8V 300 MHz - 1 GHz

1157A 2.5 GHz 10:1 1 kΩ, 0.8pF 5V p-p 300 MHz - 1 GHz

1158A 4 GHz 10:1 1 kΩ, 0.8pF 5V p-p 300 MHz - 1 GHz

High Voltage Passive Probe10076B 250 MHz 100:1 1 MΩ, 20pF 4 kVpk

N2771B 50 MHz 1000:1 1 MΩ, 20pF 30 kVpk

AC/DC Current Probe1146A 100 kHz 0.1 V/A or 0.01 V/A 1MΩ Max.: 30 A peak, 15 A rms cont.

1147A 50 MHz 0.1 V/A - Max.: 30 A peak, 15 A rms cont. 300 MHz - 1 GHz

N2780B 2 MHz 0.01 V/A - Max.: 500 A peak, 700 A rms cont.

N2781B 10 MHz 10 MHz - Max.: 150 A peak, 300 A rms cont.



10070D/10073D/10074D

N2791A

1147A/N2893A

N2795A/N2796A

Phone 1 866 663 8233

Bench Multimeters Test & Measurement

24

34405A Digital Multimeter, 5 1/2 digitThe 34405A features simultaneous reading of DC and AC measurements with its dual display andcan take up to 19 readings/sec at 4 1/2 digit resolution through the standard USB interface. The SCPI language compatibility makes it easy to migrate from your existing test setup.Features: 120000 counts resolution 16 measurement functions including temperature and capacitance 0.025% DC voltage accuracy USB 2.0, USBTMC-USB488 device class SCPI language compatible Comes with DMM Intuilink data logging software

34401A Digital Multimeter, 6 1/2 DigitThe Agilent 34401A is the world´s best selling benchtop Digital Multimeter (DMM). This industrystandard multimeter provides uncompromising performance for system and benchtop testing.Features: .0035 % basic DC accuracy, .06 % basic AC accuracy, .01 % basic Ohms accuracy 1000 readings/second in ASCII format across the GPIB bus Configuration rates: 26/sec to 50/sec Autorange rate (DCV): > 30/sec Comes with DMM Intuilink data logging software

34410A Digital Multimeter, 6 1/2 Digit High PerformanceThe Agilent 34410A builds on the industry-standard 34401A. The 34410A adds improved accuracy,improved measurement speed and throughput, LAN and USB connectivity and expandedmeasurements.Features: .0030 % basic DC accuracy Capacitance & Temperature Data Logger with 50,000 reading non-volatile memory LAN (LXI Class C), USB & GPIB standard 10,000 readings/sec @ 5 1/2 digits to the PC 1,000 readings/sec @ 6 1/2 digits to the PC Comes with DMM Intuilink data logging software

34411A Digital Multimeter, 6 1/2 Digit Enhanced PerformanceThe 34411A has all the features of the 34410A plus 50,000 readings/sec, 1M volatile memory,analog trigger leveling and programmable triggering.Features:All the features of the 34410A, plus: 50,000 readings/ sec. @ 4 1/2 digits to the PC 1M reading memory Analog level and pre/post triggering Comes with DMM Intuilink data logging software

34420A NanoVolt, Micro-Ohm Meter, 7 1/2 DigitThe Agilent 34420A nanoVolt/micro-Ohm meter is a high-sensitivity multimeter optimized forperforming low-level measurements. It combines low-noise voltage measurements with resistance andtemperature functions, setting a new standard in low-level flexibility and performance.Features: 100 pV / 100 nOhm sensitivity 1.3 nVrms / 8 nVpp noise performance Built-in low noise 2 channel scanners 3 low power, dry circuit testing built-in

resistance functions Direct SPRT, RTD, Thermistor,

and Thermocouple measurements Comes with DMM Intuilink data logging software

MPN # Description 34405A Digital Multimeter, 5 1/2 digit

MPN # Description 34401A Digital Multimeter, 6 1/2 Digit

MPN # Description 34410A Digital Multimeter, 6 1/2 Digit High Performance

MPN # Description 34411A Digital Multimeter, 6 1/2 Digit

Enhanced Performance

MPN # Description 34420A NanoVolt, Micro-Ohm Meter, 7 1/2 Digit

Phone 1 866 663 8233

25

Test & Measurement Bench Multimeters

Benchtop DMM’sFor a broad spectrum of laboratory and service applications providingcurrent, voltage, resistance diode, frequency and continuity measurements. 0.03% basic VDC accuracy (0.02% 5491B) Dual display VFD AC + DC True RMS Up to 25 readings per second measurement rate AC volt and amp measurement

over wide frequency range (ACV100 kHz/ACI 20 kHz)

Limit mode for Pass/Fail testing Built-in math functions:

Rel, Max/Min, dBm, dB, %,Hold, Compare

CATI (1000 V)/CATII (300 V)protection

USB interface (Virtual Com) RS232 interface (5491B only) SCPI compatible

6.5 Digit Dual DisplayBenchtop PrecisionMultimeters Basic V dc accuracy of

up to 0.0024 % 100 µA to 10 A current

range, with up to 100 pA resolutionWide ohms range from

10 Ω to 1 GΩ with up to10 µΩ resolution 2 x 4 ohms 4-wire measurement technique Both models measure frequency and period 8846A also measures capacitance and temperature Graphical display Trendplot™ paperless recorder mode, statistics, histogram

5.5 Digital BenchMultimeter 5.5 digit resolution Dual DisplayMeasures V dc/ac,

I dc/ac, Ω, Freq,Continuity, Diode Basic V dc accuracy of up to 0.015%Min, Max, Rel, dB, dBm 2x4 Wire Ohms measurement technique Dedicated dc leakage current ranges Six dedicated buttons for fast access to instrument setups Hi/Lo limit compare for Pass/Fail testing RS-232 interfaceMPN # Description 8808A Benchtop Multimter

8846A

2831E

MPN # In Store Description 2831E 4 1/2 Digit True RMS Bench Digital Multimeter 5491B 50,000 Count Digit Dual Display Bench Multimeter

MPN # Description 8845A Benchtop Precision Multimter8846A Benchtop Precision Multimter

MPN # Description U3606A Multimeter / DC power supply

U3606A Multimeter / DC power supply

Supply and measureThis convenient new hybrid combines a 5½-digit DMM and 30-W dual-range supply in a single unit. Operating simultaneously and independently,the instruments provide efficient, affordable testing while saving space onthe bench or in a rack. The DMM includes essential multimetercapabilities as well as four-wire milliohm measurements and four mathfunctions. The power supply adds overvoltage and overcurrent protectionplus auto scan and ramp, and a square-wave generator. Key features: Two instruments in one box that saves space and enables simultaneous,

independent operations Basic 5.5-digit DMM functions + 4-wire milliohm measurement Basic DC power supply functions with protection features + auto scan

and ramp + square-wave USB-TMC488.2 and GPIB connectivity Universal AC input Kensington lock slot

MPN # Description U3401A Dual Display Benchtop Digital MultimeterU3402A Dual Display Benchtop Digital Multimeter

U3400 Series Digital Multimeters

Basic + Good = Elegant SimplicitySome of the best equations express large ideas with elegant simplicity.The same is true with the Agilent U3401A and U3402A dual-displayDMMs. When you need basic capabilities with good performance at 4½or 5½ digits, respectively, these affordable benchtop units make thegrade in educational, electronics and communications applications.Key features: Up to 120,000 counts resolution Up to 0.012% DCV accuracy 11 basic measurements:

DC, AC and AC+DC (True RMS) voltage and currentSelectable 2 or 4-wire resistance (Note: 2-wire only, for U3401A)Frequency, continuity and diode tests

Dual display on bright VFD Built-in math functions: dBm, Relative, Min/Max, Compare, Hold Selectable resolutions for variable measurement speeds (U3402A only) Kensington lock slot helps to secure instrument and prevents theft

or misplacement

Phone 1 866 663 8233

Generators & Power Supplies Test & Measurement

26

Multi-Output D.C. Power Supplies Up to four independent DC outputs Constant Voltage and Constant Current Operation Auto Series, Parallel and Tracking Operation 4 LED displays selectable for two sets

output voltage & current displayssimultaneously Low Ripple and Noise Overload and Reverse Polarity Protection Selectable for Continuous/Dynamic Load Fan speed control for noise reduction

MPN # Description GPS-2303 Multi-Output DC Power SupplyGPS-3303 Multi-Output DC Power SupplyGPS-4303 Multi-Output DC Power Supply

SPECIFICATIONS Voltage Current FixedGPS-2303 0-30V x 2 0-3A x 2GPS-3303 0-30V x 2 0-3A x 2 5V/3A fixedGPS-4303 0-30V x 2 0-3A x 2 2.2-5.2V, 1A fixed,

8-15V, 1A fixedGPS-4251 0-25V x 2 0-0.5A x 2 3-6V, 2.5A fixed,

8-15V, 1A fixed

Function Generators GFG-8020H (0.2Hz ~ 2MHz) Sine, Triangle, Square, TTL pulse

and CMOS Output Built-in 4 Digit Counter (INT only)

GFG-8215A (0.3Hz ~ 3MHz)Waveforms: Sine, Triangle, Square,

Ramp, TTL and CMOS External Voltage Controlled

Frequency (VCF) Function External Voltage Control with

Signal Inversion Capability Variable DC Offset Control Two-Step (-20dB x 2) and Variable

Attenuator

GFG-8216A (0.3Hz ~ 3MHz)GFG-8250A (0.5Hz ~ 5MHz)Also includes: Built-in 6 high res. 6 digit int/ext

counter to 150MHz Frequency counter

GFG-8255A (0.5Hz ~ 5MHz)GFG-8210 (0.1Hz ~ 10MHz)Also includes: INT./EXT. AM/FM Modulation LIN/LOG Sweep Mode GCV Output for synchronization

GFG-3015 (0.01Hz~15MHz)Max. Frequency Resolution

10mHz Dual Display Indicate Frequency

and Amplitude Built-in 6-digit Counter with

INT/EXT Function up to 150MHzHigh Resolution Output Waveforms Sine, Square,

TTL, Triangle, Ramp, Pulse, AM,FM, Sweep, Trigger and Gate / Burst VCF for 100:1 EXT

Frequency Control INT/EXT, AM/FM Modulation GCV Output for Synchronization Variable DC Offset Control RS-232C Interface Standard Output Overload Protection LIN/LOG Sweep Mode SYNC Output

GFG-3015

GPS-3033

MPN # Description GFG-8020H 2MHz Function GeneratorGFG-8215A 3MHz Function GeneratorGFG-8216A 3MHz Function Generator w/counterGFG-8250A 5MHz Function Generator w/counterGFG-8255A 5MHz Function Generator w/counter, sweep, AM/FMGFG-3015 15MHz Function Generator w/counter, sweep, AM/FM

DDS Generator DDS Technology and

FPGA Chip Design Frequency Ranges:

0.1Hz~4MHz, 0.1Hz~7MHz,0.1Hz~10MHz Frequency Resolution: 100mHz High Frequency Accuracy & Stability: ± 20ppm Low Distortion Sine Wave: -55dBc, 0.1Hz~200kHz Save/Recall settings with 10 Groups of Setting MemoriesMPN # Description SFG-1003 3MHz DDS FGSFG-1013 3MHz DDS FGSFG-2004 4MHz DDS FGSFG-2104 4MHz DDS FG with CounterSFG-2007 7MHz DDS FGSFG-2107 7MHz DDS FG with CounterSFG-2010 10MHz DDS FGSFG-2110 10MHz DDS FG with CounterSFG-2020 20MHz DDS FGSFG-2120 20MHz DDS FG with Counter

SFG- 2104

D.C. Switching Power Supply Two Digital Panel Meters 0.01% High Regulation Constant Voltage and

Constant Current Operation High Efficiency High Power Density Overload & Reverse Polarity Protection

SPS- 3610

SPECIFICATIONS Independent Series ParallelGPC-3030D 0~30V x 2 0~3A x 2 60V 3A, 30V 6AGPC-3060D 0~30V x 2 0~6A x 2 60V 6A, 30V 12AGPC-6030D 0~60V x 2 0~3A x 2 120V 3A, 60V 6A

D.C. Power Supply 3 1/2 Digits 0.5" LED Display 0.01% High Regulation Constant Voltage and Constant

Current Operation Series or Parallel Operation Function Remote Control by External Voltage Internal Select for Continuous

or Dynamic Load Low Ripple and Noise Overload and Reverse Polarity Protection

MPN # Description GPS-1850D DC Power Supply 0-18V, 0-5A GPS-3030D DC Power Supply 0-30V, 0-3AGPR-3060D DC Power Supply 0-30V, 0-6AGPR-6030D DC Power Supply 0-60V, 0-3AGPC-1850D DC Power Supply, Triple OutputGPC-3030D DC Power Supply, Triple OutputGPC-3060D DC Power Supply, Triple OutputGPC-6030D DC Power Supply, Triple Output

GPS-1850D

MPN # Description SPS-1230 Switching Power Supply 0-12V, 0-30ASPS-1820 Switching Power Supply 0-18V, 0-20ASPS-3610 Switching Power Supply 0-36V, 0-10ASPS-606 Switching Power Supply 0-60V, 0-6A

Phone 1 866 663 8233

27

Test & Measurement Data Acquisition & Power Supplies

MPN # Description E3631A 80W Triple Output Power Supply, 6V, 5A & ±25V, 1A E3632A 120W Single Output Power Supply, 15V, 7A or 30V, 4AE3633A 200W Single Output Power Supply, 8V, 20A or 20V, 10AE3634A 200W Single Output Power Supply, 25V, 7A or 50V, 4AE3646A 60W Dual Output Power Supply, Two 8V, 3A or 20V, 1.5A E3647A 60W Dual Output Power Supply Two 35V, .8A or 60V, 0.5A E3648A 100W Dual Output Power Supply Two 8V, 5A or 20V, 2.5A E3649A 100W Dual Output Power Supply Two 35V, 1.4A or 60V, 0.8A

34980A Multifunction Switch/Measure Mainframe The 34980A is an eight-slotmainframe that has an optional built-in 6.5 digit DMM with your choice of19 different plug-in modules. These include switching from DC to20 GHz, digital I/O, D/A converters,and counter/totalizer functionality.

E3600A Series DC Power SuppliesThese supplies combine convenientbenchtop capabilities with flexible systemfeatures in a compact, multi-outputpackage. For bench-only applications, twomodels are available without I/O interfaces.Features: Address benchtop and ATE applications with up to three

isolated dual-range outputs in a small package Utilize GPIB and RS-232 interfaces with SCPI command set Enhance signal integrity in test systems via low-noise outputs Simplify cabling with built-in measurements Streamline tasks with front panel control & basic programmable features Ensure DUT safety with overvoltage protection

MPN # Description E3640A 30W Single Output Power Supply, 8V, 3A or 20V, 1.5A E3641A 30W Single Output Power Supply, 35V, 0.8A or 60V, 0.5A E3642A 50W Single Output Power Supply, 8V, 5A or 20V, 2.5A E3643A 50W Single Output Power Supply, 35V, 1.4A or 60V, 0.8A E3644A 80W Single Output Power Supply, 8V, 8A or 20V, 4A E3645A 80W Single Output Power Supply, 35V, 2.2A or 60V, 1.3A E3646A 60W Dual Output Power Supply, 8V, 3A or 20V, 1.5AE3647A 60W Dual Output Power Supply, 35V, 0.8A or 60V, 0.5AE3648A 100W Dual Output Power Supply, 8V, 5A or 20V, 2.5AE3649A 100W Dual Output Power Supply, 35V, 1.4A or 60V, 0.8A

E3640A Series Programmable DC Power SuppliesThese supplies combine convenient benchtop capabilities with flexiblesystem features in a compact, dual-range, single to dual output package.For bench-only applications, two models are available without I/O interfaces.Features: Remote sensing, eliminating voltage

regulation errors caused by drop inload leads

Front/rear output terminals Internal non-volatile memory, store

and recall setups fast Overvoltage protection (OVP) features

E3646A

E3645A

MPN # Description U8001A DC Power Supply, 30V, 3AU8002A DC Power Supply, 30V, 5A

MPN # Description 34970A Data Acquisition Switch Unit34972A LXI Data Acquisition Switch Unit34830A BenchLink Data Logger Pro Software34901A 20 Channel Multiplexer (2/4-wire) Module34902A 16 Channel Multiplexer (2/4-wire) Module34903A 20 Channel Actuator/GP Switch Module 34904A 4 x 8 Two-Wire Matrix Module34905A 2 GHz Dual 1:4 RF Mux, 50 Ohm Module34907A Multifunction Module34908A 40 Channel Single-Ended Multiplexer Module

MPN # Description 34980A Multifunction Switch/Measure Unit34832A BenchLink Data Logger Pro Software34921A 40-channel Armature Multiplexer w/ low thermal offset 34922A 70-channel Armature Multiplexer 34923A 40/80-channel Reed Multiplexer 34924A 70-channel Reed Multiplexer 34925A 40/80-channel optically isolated FET Multiplexer 34931A Dual 4x8 Armature Matrix 34932A Dual 4x16 Armature Matrix 34933A Dual/Quad 4x8 Reed Matrix 34937A 28-channel Form C & 4-channel Form A Module34938A 20-channel 5-amp Form A Module34941A Quad 1x4 50 ohm 3 GHz RF Multiplexer 34942A Quad 1x4 75 ohm RF Multiplexer 34945A Microwave switch/attenuator Driver 34950A 64-bit digital I/O with memory and counter 34951A 4-channel isolated D/A converter with waveform memory34952A Multifunction module with 32-bit DIO, 2-ch D/A and totalizer34959A Breadboard module

Data Acquisition Switch UnitsData Acquisition Switch Units are compact, economical, one-box solutions for data logging, data acquisition, and general-purpose switching and control applications.Choose from eight optional plug-in modules to create a compact data logger,full-featured data acquisition system or low-cost switching unit.Features: 3-slot mainframe with built-in GPIB and RS232 interfaces for 34970A

and USB and LAN (LXI-C) for 34972A 6 1/2-digit (22-bit) internal DMM, scanning up to 250 channels/second 8 switch and control plug-in modules to choose from Built-in signal conditioning measures thermocouples, RTDs and

thermistors, ac/dc volts and current; resistance; frequency and period 50k readings of non-volatile memory holds data when power is removed Hi/LO alarm limits on each channel, plus 4 TTL alarm outputsThe 34972A built-in LAN and USB interfaces allows easy connection to aPC or laptop without needing to purchase additional IO cards or converterinterfaces. Use a USB flash drive to upload data logging configurations fromBenchLink Data Logger into the 34972A and to transfer large data sets backto the computer. Simply connect the USB stick to your PC when you returnand easily import into a spreadsheet or other applications for data analysis.

U8000 Series Manual DC Power SuppliesGet excellent value along with greater efficiency in your work. Prevent device damage. Reduce set-up time. Minimize measurement errors.Features: Fast 50µsec transient response Fully integrated OVP and OCP Excellent regulation (0.01% + 2mV; 0.02% + 2mA) Low output noise of 1mVrms and 3mArms from 20Hz to 20MHz Keypad lock feature & physical lock mechanism Save and recall 3 memory states LCD display with backlight on/off

Phone 1 866 663 8233

Power Supplies & Generators Test & Measurement

28

MPN # Description 33250A Function / Arbitrary Waveform Generator, 80 MHz

MPN # Description 53210A 350 MHz RF Frequency Counter (10 digits/s)53220A 350 MHz Universal Counter (12 digit/sec, 100 ps)53230A 350 MHz Universal Frequency Counter/Timer (12 digits/s, 20 ps)

33210A Function / Arbitrary Waveform Generator, 10 MHzThe most affordable Function Generator offering uncompromisingperformance at a lower price for basic functions and waveforms.Features: USB, GPIB and LAN (LXI) interfaces included Graph mode for visual verification of signal settings Option 001 provides multiple-unit link for synchronous channels 10 MHz sine and square waveforms Option 002 provides 14-bit, 50 MSa/s 8 K-point arbitrary

waveform generator Ramp, triangle, noise, pulse

generation with variable edge, and DC waveforms

AM, FM, and PWMModulation, linear &logarithmic sweeps and burst all standard

MPN # Description U8031A Triple Output DC Power Supply, 30V/6A (2x) & 5V/3A; 375WU8032A Triple Output DC Power Supply, 60V/3A (2x) & 5V/3A; 375W

Agilent U8030 Series TripleOutput Power Supply Higher Power. Better Reliability. UnrivalledPerformance. Wow, the power supply in itsclass to offer output sequencing that canbe setup and generated right from the frontpanel without any computer programming.With this feature, integrated with easy touse functions like auto-tracking, excellent load and line regulation, cleannoise, and safety features, you get a solid and reliable triple-output powersupply at an unsurpassed performance.Features: Provides total power of 375 W for three outputs Output sequencing capability Excellent load and line regulation

(CV: < 0.01% + 2 mV; CC: <0.02% + 2 mA) ensures stable output Provides clean output with ≤ 1 mVrms (0.5 mVrms typical) noise Fast < 50 µsec transient response for stable testing

33500 Series Function / Arbitrary Waveform GeneratorsRevolutionary signal generation delivers the highest signal fidelity in itsclass, full-bandwidth pulses, and real point-by-point arbitrary waveforms.

The Agilent 33500 Series of function/arbitrary waveform generators is thefirst in its class with 30 MHz sine, square, and pulse waveforms and 250MSa/s, 16-bit sampling with true point-by-point arbitrary waveforms. The33500 Series comes in 1- and 2-channel configurations with a large colordisplay and embedded waveform builder. The 2-channel model has aflexible dual-channel mode with frequency and amplitude coupling,differential channels, and combined output channels.

Features:More bandwidth: 30 MHz sine, square, and pulse bandwidth High signal fidelity: 0.04% total harmonic distortion and < 40 ps jitter USB and LAN (LXI) interfaces included, option 400 adds GPIB Better time resolution: 250 MSa/s, 16-bit sampling rate Point-by-point arbitrary waveforms with sequencing Dual-channel mode with independent or coupled channels 1 MSa/s waveform memory standard, option 002 provides 16 MSa/s Optional 33503A BenchLink Waveform Builder Pro software (or a free

version available for download)

53200 Series Frequency Counters/TimersFast, precise frequency measurements.

350 MHz with options to 15 GHz 20 ps single-shot time interval

measurements Continuous, gap-free measurements,

with time stamps on signal edges Advanced capabilities: Histograms,

trending, datalogging, optionalpulse/burst microwave measurements Onboard memory for 1 M readings Standard USB, LAN (LXI-C) and GPIB 53131A, 53132A, 53181A counter

emulation mode

MPN # Description 33521A Arbitrary Waveform Generator - 1 Channel 33522A Arbitrary Waveform Generator - 2 Channel

33522A

Model 53210A 53220A 53230AType 1 channel RF: 2 channel universal: 2 channel universal:

optional channel 2 optional channel 3 optional channel 3Measurements Frequency, frequency ratio, period, max/min/peak-to-peak input voltage

Time interval, rise/fall time, single periodpulse width, duty cycle, phase, totalize

Timestamp/MDAFrequency range (optional) DC to 350 MHz (6 or 16 GHz)Frequency resolution 10 digits/s 12 digits/sTime Interval N/A 100 ps 20 ps

MPN # Description 33210A Function / Arbitrary Waveform Generator, 10 MHz

33250A Function / Arbitrary Waveform Generator, 80 MHzAn 80 MHz function / arbitrary waveform and pulse generator in oneinstrument with very stable frequencies and low distortion. It also provides AM, FM, and FSK modulation capabilities, sweep and burst modes, and a graphic display. Features: GPIB & RS-232 interfaces Graph mode for visual verification of signal settings Built-in multiple-unit link for synchronous channels Benchlink Waveform Builder software works with all function generators 80 MHz sine and

square waveforms Ramp, triangle, noise

and DC waveforms 12-bit, 200 MSa/s, 64

Kpoint arbitrary waveforms Pulse capability with

variable edge

Phone 1 866 663 8233

29

Test & Measurement Oscilloscopes & Power Supplies

Single Output SwitchingPower SupplySingle output CV/CC100 Watt SwitchingMode Power Supplywith constant currentand tracking OVP. 4Digit Digital display. Choose from three

variable outputs Constant Voltage /

Constant Current LCD Voltage &

Current Display Two Year Warranty

MPN # Description PSC-260 Power Supply (1-60VDC @ 1.6A) PSC-336 Power Supply (1-36VDC @ 3A)PSC-520 Power Supply (1-20VDC @ 5A)

MPN # Description PSB-330T Power Supply - Triple Variable

Power Supply - Triple Output (2 x 0-30VDC @ 3A / 5VDC @ 3A)Triple output constant voltage/constant current DC adjustable power supply. There are three modes ofoperation: Independent, Serial, and Parallel. In the Independent mode, there are two variableoutputs: 0-30 VDC @ 3 Amps each and a constant 5 VDC @ 3 Amps. In Serial mode, the output is0-60 VDC @ 3 Amps and a constant 5 VDC @ 3 Amps. In Parallel mode, the output is 0-30 VDC @6 Amps and a constant 5 VDC @ 3 Amps. Switchable Independent Series / Parallel Operation Two Variable 0-30VDC @ 3.0A Outputs Fixed 5 VDC @ 3.0A Output Constant Voltage / Constant Current LCD Voltage & Current

Digital Storage OscilloscopesIntroducing a new series of Digital Storage Oscilloscopes that are compact,portable and equipped with extensive diagnostic features yet are affordablypriced. They also carry the CSA special inspection that is crucial to theeducational institutions.All 3 models come with a large colour LCD display, easy USB connectivity,advanced triggering functions, long waveform memory, easy pass/fail testingand 32 automatic measurements. Remote PC control is made easy withEasyscope software that allows complete access to the oscilloscopeincluding the front panel controls. 25 MHz, 60 MHz and 150 MHz Bandwidth

Sampling rate up to 1 GS/s Dual Channels 5.7" Colour LCD Display 32 Automatic measurements Front panel USB host interface for quick saving to a memory stick Rear panel USB & RS-232 port allows direct remote PC control Triggering capabilities include Edge, Pulse Width, Video, Slope and

Alternating triggerMath functions include Add, Subtract, Multiply, Divide and FFT Digital Filtering on each channel Long waveform memory up to 40 kpts/Ch. Pass/Fail function, Waveform recording functionWaveform intensity controlMulti-language user interface and context sensitive (French and Spanish) Two x10/x1 Switchable Probes, USB Cable,

EasyScope PC software included Two year warranty

SPECIFICATIONS PSB-330TOutput Voltage 0-30, 0-30, 5VDCOutput Current 3, 3, 3ADCLoad Regulation +/-0.01% +5mVLine Regulation +/-0.01% +3mVRipple And Noise <0.3mV RMSPower Requirements 120 VAC/60Hz

GDS-1072-U Digital StorageOscilloscope 70 MHz Bandwidth 2 Input Channels 250MSa/s Real-Time and 25GSa/s

Equivalent-Time Sampling 4k Memory Length per Channel Peak Detect as Fast as 10ns

Save/Recall of 15 Front Panel Settings & Waveforms 5.7" TFT Color Display 19 Auto Measurements Arithmetic Operators - Add, Subtract, FFT USB Port for PC Connection Data Logger Limited Lifetime Warranty

MPN # Description GDS-1072-U 70Mhz, 2 channel Oscilloscope

MPN # Description CDS-2022 25 MHz Oscilloscope

500 MS/s Sampling rate, 20 kpts/Ch.CDS-2062 60 MHz Oscilloscope

1 GS/s Sampling rate, 40 kpts/Ch.CDS-2152 150 MHz Oscilloscope

1 GS/s Sampling rate, 40 kpts/Ch.

Phone 1 866 663 8233

Oscilloscopes & Power Supplies Test & Measurement

30

Triple Output 30VDC, 3A Digital Display Power Supply 1670A: 30V, 3A,

one 12 VDC fixed one5 VDC fixed section 1671A: 30V, 5A,

one 12 VDC fixedsection, one 5 VDCfixed section 1672: 5V, 3A, and

two variable outputs (0 – 32V/ 0 – 3A)ratings 1673: 5V, 3A, and

two variable outputs (0 – 32V/ 0 – 6A) ratings

4 Digit Display DC Power SuppliesThese bench power supplies have both coarse and fine voltage and currentcontrol knobs and dual LED displays to continuously monitor both outputcurrent down to 1 mA and voltage down to 10 mV

MPN # Description 1670A Triple-Output 30V, 3A Digital Display DC Power Supply1671A Triple-Output 30V, 5A Digital Display DC Power Supply1672 207W Triple Output Quad Display DC Power Supply1673 400W Triple Output Quad Display DC Power Supply

MPN # Description 1692 3-15VDC, 40A Switching Digital DC Power Supply 1693 1-15V, 60A Switching DC Power Supply with Remote Sense1694 1-30V, 30A Switching DC Power Supply with Remote Sense1900 1-16V, 60A Switching DC Power Supply1901 1-32V, 30A Switching DC Power Supply1902 1-60V, 15A Switching DC Power Supply

Digital Storage OscilloscopesThese Digital Storage Oscilloscope deliver an unmatched combination ofperformance and value. 2530B: 25 MHz, 500MSa/s, 2 Ch, 5.7" Color LCD, entry level DSO.

Analog style knobs and one touch automatic setup. Supports cursors withreadouts, 32 automatic measurements, and extensive trigger capabilities 2532B: 40 MHz, 500MSa/s, 2 Ch, 5.7" Color LCD, entry level DSO.

Analog style knobs and one touch automatic setup. Supports cursors withreadouts, 32 automatic measurements, and extensive trigger capabilities 2540B: 60 MHz, 1 GSa/s, 2-Ch, color display DSO with features such as

deep memory up to 2.4 Mpts, digital filtering, FFT, waveform recorder,and mask testing. Includes LAN and USB port for remote control. 2542B: 100 MHz, 1 GSa/s, 2-Ch, color display DSO with features such

as deep memory up to 2.4 Mpts, digital filtering, FFT, waveform recorder,and mask testing. Includes LAN and USB port for remote control.

Additionally, the instrument comes with PC Software that lets you easilycapture, analyze and document waveforms and measurement results.

MPN # Description 2530B 25 MHz, 500 MSa/s Digital Storage Oscilloscope2532B 40 MHz, 500 MSa/s Digital Storage Oscilloscope2540B 60 MHz, 1 GSa/s Digital Storage Oscilloscope2542B 100 MHz, 1 GSa/s Digital Storage Oscilloscope

MPN # Description 1715A 4 Digit Display DC Power Supply (0-60V, 0-2A) 1735A 4 Digit Display DC Power Supply (0-30V, 0-3A) 1743B 4 Digit Display DC Power Supply (0-35V, 0-6A) 1745A 4 Digit Display DC Power Supply (0-35V, 0-10A)

Switching DC Power Supplies 1692: 3-15VDC, 40A Switching Digital DC Power Supply: These bench

power supplies have a coarse voltage control knobs and dual LED displaysto continuously monitor both output current down to 100 mA and voltagedown to 100 mV capabilities 1693: 1-15V, 60A Switching DC Power Supply with Remote Sene:

1694: 1-30V, 30A Switching DC Power Supply with Remote Sense:High current bench DC power supplies with coarse voltage control knoband dual LED displays to continuously monitor both output current downto 100 mA and voltage down to 100 mV 1900: 1-16V, 60A Switching DC Power Supply: 960W DC power supply

with remote sense, rotary encoder tuning for coarse and fine voltage andcurrent control, and dual LED displays to monitor output current down to100 mA and voltage down to 100 mV 1901: 1-32V, 30A Switching DC Power Supply:

1902: 1-60V, 15A Switching DC Power Supply:960W (#1901) and 900W (#1902) DC power supplies with rotaryencoder tuning for coarse and fine voltage and current control and dualLED displays to monitor output current down to 100 mA and voltage down to 100 mV

2542B

Phone 1 866 663 8233

31

Test & Measurement Generators & Programmers

Component TestersComponent testers canmeasure values of capacitors, resistors,inductors, diodes ortransistors. The measured values ofthese components can beused for component sortingor trouble shooting.

MPN # Description 815 Handheld Component Tester830C Dual Display Capacitance Meter to 200 mF 875B LCR Meter 878B Universal LCR Meter 879B Deluxe Universal LCR Meter 885 Synthesized LCR/ESR Meter with SMD Probe 886 Synthesized In-Circuit LCR/ESR Meter w/100kHz test freq. 889B Synthesized In-Circuit LCR/ESR Meter w/component tester890C Dual Display Capacitance Meter to 50 mF

MPN # Description 844USB Device Programmer with USB PC Interface 866B Universal Device Programmer with USB Interface

Signal GeneratorSignal generators outputrepeating or non-repeating ACor pulsed signals. They allow themanipulation of the output signalsfrequency, amplitude or shape. The circuit architecture thatcreates the output signals can begenerated using either analog ordigital circuits.MPN # Description 4003A 4 MHz Sweep Function Generator4011A 5MHz Function Generator4040A 20MHz Sweep Function Generator

879B

815

Device Programmers844USB is a great low cost USB interface programmer designed for anyonewho wants to read, copy, program or burn common IC’s.

USB 2.0/1.1 Interface

40 pin DIL ZIF (Zero Insertion Force) socket accepts both 300/600 mil devices up to 40 pins

866B is a universal device programmer with a constantly updated extensive device library. Whether you are working with PLCC, SOIC, TSOP, DIP, TQFP,SSOP, PSOP or QFP, B+K Precision has an extensive line of socket adaptersto interface with any IC package.

MPN # Description 4005DDS 5 MHz DDS Function Generator

5 MHz DDS Function Generator The B&K Precision model 4005DDS is a versatile 5 MHz DDS (directdigital synthesis) function generator with a 4-digit display. The instrumentgenerates sinusoidal, triangular, and square waveforms over the 1 Hz to 5MHz range at precise frequencies. Frequency is selectable from 1 Hz to 5 MHz Sine, square, or triangle waveform output Direct digital synthesis (DDS) architecture Bright, easy-to-read LED display Number pad for quick input of frequency Attenuate output by up to 40 dB Adjustable duty cycle and DC offset

Handheld Digital MultimeterB&K Precision provides an extensive selection of digital and analog multimeters, suitable for use in the field, lab, and many other environments.

MPN # Description 2703C Manual Ranging Tool Kit Digital Multimeter2704C Manual Ranging Tool Kit DMM with Transistor Test2705B Auto Ranging Tool Kit Digital Multimeter2706B Manual Ranging Tool Kit DMM with Temperature2707B Manual Ranging True RMS Tool Kit Digital Multimeter2708B Auto Ranging True RMS Tool Kit Digital Multimeter2709B Auto Ranging True RMS Tool Kit Digital Multimeter

2703C 2704C 2705B 2706B 2707B 2708B 2709BDisplay Count 2000 2000 3400 2000 2000 3400 6600True RMS Min/Max Hold Data Hold Capacitance Frequency Logic Level Transistor Gain Temperature Auto Power Off

Phone 1 866 663 8233

Accessories Test & Measurement

32

Mini-Plunger to BNC Male with RG58 BNC Connector, gold-plated center contact

and silver-plated body Coaxial Cable,

shielded RG58C/U, 50 ohm

Plunger: nylon housing, stainless steel spring and beryllium copper contact

MPN # Description 110009 Test Lead Set (shrouded)110013 Test Lead Set (unshrouded)

Test Probe to Right Angle Shrouded B PlugMultiple feature test prod to shielded right anglebanana plug. Length 48” Set of 2, black

and red

MPN # Description 110005 Test Lead Kit

Test Leads KitTest leads kit includes: 48” black and red multiple feature test prod

to unshielded banana plug 1 red, 1 black insulators,

insulated plunger-hook, 2 alligator clips, 2 spade lugs & 2 insulator extensions

MPN # Description 110004 Test Lead Set

Test Leads SetMade of ABS, they have anti-slip ribs for suregrip. Nickel plated 8-32 brass insert made ofalloy 360 with a type 410 stainless steel needle tip is a standard on all items Test prod to right

angle shielded banana plug

MPN # Description 80120 12” Test Lead Set80119 18” Test Lead Set80121 18” Test Lead Set

Insulated Alligator Lead Set Test leads kit includes: #80119: Insulated “mini-alligator” lead set 2

Black, 2 Red, 2 Yellow, 2 Green, 2 White #80120: Insulated “alligator” lead set

1 Black, 1 Red, 1 Yellow, 1 Green, 1 White #80121: Insulated “alligator” lead set

2 Black, 2 Red, 2 Yellow, 2 Green, 2 White

MPN # Description 80012 36” Test Lead


BNC Female Breakout to Mini-Micro-Grabbers BNC Female Connector: quality tarnish-

resistant, plated brass with a gold-plated brasscenter contact

ABS housing; Mini-Micro-Grabbers (No.208):conductor and abrasion resistant, nylon housing

Hook-up Wire: #20 AWG (41/36) tinnedcopper with 105°C PVC insulation


Banana Plug Insulated Alligator Clip toStackable Banana Plug Banana Plug, ABS housing, brass body and

beryllium copper, nickel-plated, nine-leaf cage spring

Alligator Clip, nickel plated steel with PVC insulator

Wire, 20AWG tinned copper with 105°C PVC insulation


BNC Male Breakout to InsulatedMini-Alligator Clips BNC Male Connector, quality

tarnish-resistant, plated brass with a gold-plated brass center contact

ABS housing; Clip, Mueller No. 30BL with No. 31 insulators

Hook-up Wire, 20AWG tinned copper with PVC insulation

Mini-Plunger to Stackable Banana Plug Material: Banana Plug: ABS housing, brass

body and beryllium copper, nickel-platedWire: 20AWG tinned copper w/PVC insulationPlunger: nylon housing, stainless steel springand beryllium copper contact

Set of 2, black and red, 36" (.9m) length

Rating: Hands free testing at 300V, 5 Amps

MPN # Description 80006 Test Lead Set

Phone 1 866 663 8233

33

Test & Measurement Accessories

80AK-A DMM Adapter Adapts Type-K thermocouple

mini-connector to dual shroudedbanana plug inputs Compatible with all Fluke DMMs

with temperature measurementfunctions

MPN # Description 80PK-1 Bead Probe

80PK-1 Bead Probes Compatible with K-type

thermometers 1m (39 in.) lead wireMeasurement range: -40°C to

260°C (-40°F to 500°F)

MPN # Description 80PK-3A Surface Probe

80PK-3A Surface Probe For measuring the temperature of

flat or slightly convex surfacesMeasurement range: 0°C to 260°C

(32°F to 500°F)

80PK-22 ImmersionTemperature Probe For use in liquids, gels, or general

measurement use. 8.375” Inconel 600 probeMeasurement range:

-40°C to 1090°C (-40°F to 1994°F)

MPN # Description 80PK-24 Temp. Probe


80PK-26 TaperedTemperature Probe For general purpose surface and

air measurements 304 stainless steel probe Measurement range:

-40°C to 816°C, (-40°F to 1500°F)


80PK-27 Industrial SurfaceTemperature Probe For flat or slightly curved

industrial surfaces 8” 304 stainless steel probe Measurement range:

-127°C to 600°C (-196°F to 1112°F)


80PK-24 Air TemperatureProbe For air and non-caustic gas

measurements 8.5” inconel probeMeasurement range:

-40°C to 816°C, (-40°F to 1500°F)

Current ClampsCurrent clamps are the ideal tools to extend the functionality of Fluke tools.

AC Current Clamps

AC/DC Current Clamps

MPN # Description 80i-110s AC/DC Current Clampi30 AC/DC Current Clampi30s AC/DC Current Clampi200 AC Current Clampi200s AC Current Clampi400 AC Current Clampi410 AC/DC Current Clampi1000s AC Current Clampi1010 AC/DC Current Clampi2000flex AC Current Clamp

i1010

i410

i30s

i30

80i-110s

i200

i200S

i1000S

SPECIFICATIONS 80i-110s i30 i30s I410 i1010DC Range 0.1 to 100A 30A 30A 1 to 400A 1 to 1000AAC Range 0.1 to 70A 20A 20A 1 to 400A 1 to 600AAccuracy 100mV/A: 50mA-10A ±3% 1% ± 2mA 1% ± 2mA 3.5% + 0.5A 2% + 0.5A

10mV/A: 50mA-40A ±4%40A -80A ±12%80-100A ±15%

Bandwidth (-3dB) 100kHz 20kHz 100kHz 3kHz 10kHzMax. Conductor Dia. 11.8mm 19mm 19mm 30mm 30mmMax. Conductor Size 1AWG 250MCM 250MCM 750MCM 750MCM

or 2-500MCM or 2-500MCMOutput Levels 100mV/A 100mV/A 100mV/A 1mV/A 1mV/A

10mV/A

SPECIFICATIONS i200 i200s i400 i1000s i2000flexAC Current Range 1A to 200A 1A to 200A 1 to 400A 0.2A to 1000A 2A to 2000AAccuracy 3%+0.5A 1%+0.5A 2%+0.06A 0.2 to 10A: ± 1% of

48 to 65Hz 48 to 65Hz 45 to 400Hz 3%+0.1A full scale10A to 100A: 48 to 65Hz

2%+0.5A100A to 1000A:

1%+1A48 to 65Hz

Bandwidth (-3dB) 40Hz to 40kHz 40Hz to 40kHz 5Hz to 20kHz 5Hz to 100kHz 10Hz to 20kHzMax Conductor Dia. 20mm (0.8in) 20mm (0.8in) 32mm (1.26in) 54mm (2.13in) 177mm (6.97in)Maximum 300MCM 300MCM 750MCM 2-500MCM or 24.4inConductor Size 1 to 1000MCM circumferenceOutput Levels 1mA/A 10mV/A, 1mA/A 1mV/A, 10mV/A, 1mV/A, 10mV/A,

100mV/A 100mV/A 100mV/A

i2000flex

i400


MPN # Description 80AK-A Adapter 80PK-25 Piercing

Temperature Probe For general food service

applications 4” 316 stainless steel probe Measurement range:

-40°C to 350°C (-40°F to 662°F)

Phone 1 866 663 8233


34

MPN # Description 80TK Module

80TK Thermocouple Module Converts K-Type thermocouple

signals into mV output Includes 80PK-1 probeMeasurement range:

-50°C to 1000°C (-58°F to 1832°F)

MPN # Description 80K-40 High Voltage Probe


MPN # Description 80PK-9 Probe

80PK-9 General PurposeProbe Type-K thermocouple surface,

air and non-caustic gasesMeasurement range:

-40°C to 260 °C

80PK-8 Pipe ClampTemperature Probe For fast temperature and

superheat measurements of pipe surfacesMeasurement

range: -29 to 149°Cfor pipe diametersfrom 6.4 to 34.9 mm

80K-40 High Voltage Probe Allows a multimeter to measure

up to a 40,000 volts peak Ground clip included Intended for low energy

applications that are referenced to ground

MPN # Description AC220 Alligator Clips

AC220 10A Alligator Clips Insulated, nickel plated jaws grip

objects up to 3/8 in. Blunt tip grabs round

screw heads

MPN # Description AC280 Hook Clips

AC280 3A Hook Clips Profile narrows to .22 in. at tip Hook opening

.20 in. at front,

.08 in. at base

MPN # In Store Description PriceAC283 Pincer Clips 42.00

AC283 1A Pincer Clips 4.5 in. flexible, insulated shaft Nickel plated pincers

open to .20 in.


AC285 10A Alligator ClipsMulti-purpose tooth pattern grips

anything from fine gauge wire to a 3/4 in. nut Nickel-plated

steel jaws


AC72 10A Alligator Clips Slide-on style for test probes Jaws open to 8mm For use with TL71 and TL75 test

lead and probe sets

MPN # Description AC87 Bus Bar Clips

AC87 5A Heavy Duty BusBar Clips Plunger style, safety grip

operation with insulated, rightangle jaws Adjustable jaws open to grip

flat bus bars orround conductors

MPN # Description AC89 Piercing Clips

AC89 5A Heavy DutyInsulation Piercing Clip Plunger style, safety grip

operation with insulated jaws Small pin pierces

30 to 14 AWG insulated wire

MPN # Description AC120 3 Alligator Clips

AC120 10A Alligator Clips For use with STL120 shielded

test leads and TL75 test leads Nickel-plated steel jaw Jaws open

to 8mm

MPN # Description TP1 Test Probe Set

TP1 Slim Reach Test Probes One pair (red, black) of slender

probe bodies for probing closelyspaced or recessed terminals Hard stainless steel probe tips Flat blade design to hold securely

in blade type electrical wall sockets

Voltage Probe Set 200 MHz Double insulated safety designed

probe for ScopeMeter190 series

Includes 10:1 voltage probe,hook clip, test probe, ground leadwith hook clip, and ground leadwith mini alligator Red set includes ground spring

for probe tip

MPN # Description VPS210-G Probe Set-GreyVPS210-R Probe Set-Red

MPN # Description FTP-1 Fused Test ProbesFTPL-1 FTP Probes with

TL224 Test Leads

FTP Fused Test Probes Built-in fuses for additional

measurement protection Probes allow indication of live

voltage even with blown fuse,protecting the user from thinkingno voltage is present

MPN # Description TL175 Test LeadsTL175E Test Leads

TL175 TwistGuard™ Test LeadsThe only test leads in the worldwith adjustable length test tips for use in different measurementenvironments. By simply twistingthe test lead the user can changethe exposed probe tip length from19 mm to 4 mm (0.75 inch to 0.16 inch). New WearGuard™ lead wire

wear indicationWithstands high temperatures

and remains flexible in coldtemperatures Extra-heavy strain relief on both

probe-end and plug-end Probes always show correct

category rating for tip exposure being used

Phone 1 866 663 8233

35


MPN # Description TPAK Hanging Kit

Meter Hanging Kit Hands free

testing Includes

hanging loop strap, magnetic strap and nail hanger

TLK-220 Test Lead SetContains: AC220 Plunger StyleAlligator Clips, AC285 Large JawAlligator Clips, TP220 Sharp TestProbes, TL224 Right to StraightTest Leads & case.

MPN # Description TLK-220 Test Lead Set

TLK-225 Accessory SetContains AC220 Alligator Clip Set,AC280 Hook Clip Set, AC283Pincer Clip Set, AC285 Large JawAlligator Clip Set, TP220 TestProbe Set, TL224 Silicone TestLead Set & pouch.

MPN # Description TLK-225 Accessory Set

FVF-SC2 FlukeView FormsSoftware with cable Expand the power of the world's

most rugged, accurate handheldtest tools withFlukeView®FormsDocumentingSoftware FVF-SC2 for 180 & 280 Series

MPN # Description FVF-SC2 FVF Software

MPN # Description TL81A Test Lead Kit

TL81A Deluxe ElectronicTest Lead KitA quadfold nylon pouch containingtwo each (one black and one red)of the following items: One meter test lead, alligator

clips, probe tip extender, modulartest probe, hook-style clip testlead, pinch-style clip test lead, ICprobe tip and banana connector

TL220 10A Industrial TestLead Set Starter kit for industrial applications TP220 has round, stainless

steel tip Includes 1 pair: AC220, TP220,

TL222

MPN # Description TL220 Test Lead Set

TP220 Industrial Test Probes One pair (red, black) of

Industrial test probes Sharp, 12 mm stainless steel

tip provides reliable contact Recommended for use with TL222

and TL224 test leads

MPN # Description TP220 Test Lead Probes

TL221 10A Silicone TestLead Extension Kit Superior strain relief Includes two adapters to extend

leads 1.5m


TL222 10A Silicone Test Kit Recommended for use with

AC220, AC280, AC283 test clips Superior strain relief


TL223 10A Electrical TestLead Set Starter kit for electrical

applications TP1 has flat blades for wall

sockets Includes 1 pair: AC220,

TP1, TL224



TL224 10A SiliconeInsulated Test Leads 1.5m silicone-insulated wire

resists heat and cold Superior strain relief


TL75 10A Hard Point TestLead Set Extremely hard alloy tips

resist wear Distinctive comfort grip

probes


TL71 Premium DMM, TestLead Set Flexible silicone insulated leads

are heat and cold resistant Distinctive comfort grip probes Recommended for µV

measurements

Phone 1 866 663 8233


36

VoltAlert Voltbeat™ technology

and continuous self-test Upon detection, tip glows and beeper sounds 20V to 90V AC or 90V to 1000V AC

depending on model 2AC: Always-on for faster voltage testing, plus “Battery Check” button MPN # Description FLK2AC 2AC VoltAlert (90-1000V) straight tip1AC A1 II AC VoltAlert (90V-1000V)1LAC A II Low AC VoltAlert (20V-90V)

FLK2AC

MPN # Description C12A For 110 SeriesC25 For large DMMsC50 For 50 SeriesC90 For mid DMMsC125 For 120 Series

C12A, C25, C43, C50, C90& C125 Soft Meter Cases Zippered carrying case with inside

pockets and belt loop Detachable external pouch

(C125)

MPN # Description C190 For 190 Series

C190 Hard Case Heavy duty case with accessory

storage compartments For 190 Series ScopeMeter®

MPN # Description H5 Case

H5 Case Rugged fabric holster includes

flap for lead storage and built-inbelt loop Fits T5

testers

C550 Tool Bag Steel reinfored frame Rugged ballistic cloth Zippered storage with 25 pocketsWeather resistant

MPN # Description DV25 CAT IV AC Voltage Detector + Flashlight

CAT IV AC Voltage Detector + FlashlightDual range non-contact detection of AC Voltage. 24 to 1000VAC & 100 to 1000VAC For use on 50/60Hz circuits Audible and Visual

voltage indication AAA batteries

included

Volt Lights Non-contact AC voltage detector and LED flashlight Detects voltages from 40V-300V AC (LVD1), 90 to 600 V AC (LVD2) Detector glows blue when it's near AC voltage,

and glows red when at the source 100,000 hour bulb life AAA battery included

DIP Clip® Test Clips Designed for testing dual-in-line ICpackages on PC boards Assures positive electrical

connection Hands free testing 3916A:

16 pin with nickel silver contacts, 0.83 clip width 5014:

14 pin with nickel silver contacts, 0.72 clip width

MPN # Description 3916A 16 pin DIP Clip5014 14 pin DIP Clip

SOIC Clip® Test Clips Designed especially for in-circuittesting on Small Outline IntegratedCircuits (SOIC & SOJ). Assures positive

electricalconnection Hands free

testing

MPN # Description 5250 8 pin SOIC Clip

MPN # Description 1508 Lead Holder2708 Lead Holder4408 Lead Holder

Test Lead Holders Ideal storage for tangle-free

test leads 1508: 14 slots for max lead

diameter of .21”, orange 2708: 9 slots for max lead

diameter of .32”, blue 4408: 10 slots for max lead

diameter of .45”, black

2708

MPN # Description C550 Tool Bag

MPN # Description MTP 414-042 Volt Stick

Volt Stick Sound®

Non-contact voltage detector Detects from 110 to 1000 VAC Low battery warning indication Audible and visual indicationsIncludes AAA batteries

MPN # Description MT-702 Magnetic StickMT-702-EX Magnetic Stick

Magnet Stick®

Solenoid tester Detects presence of AC, DC or permanent magnetic field Sensitivity 300 Gauss Test magnet includedIncludes AAA batteriesExploson Proof (EX) version available

Phone 1 866 663 8233

MPN # Description LVD1 Volt LightLVD2 Volt Light

BNC to Multi-StackingBanana Plugs or leads Converts BNC cables with male

plugs to stackable banana plugsfor versatility Connectors molded

directly to the wire for added pull strength BNC w/20 AWG leads

37


MPN # Description B-12-0 Lead, 12”, blackB-12-2 Lead, 12”, redB-24-0 Lead, 24”, blackB-24-2 Lead, 24”, redB-36-0 Lead, 36”, blackB-36-2 Lead, 36”, red

Multi-Stacking BananaPlug Patch CordsMates to 1581 or standard

banana jack Cross and vertical stacking

banana plug Ideal for providing jumpers

or chassis boxes

MPN # Description 3788 Test Clip

BNC (f) to Minigrabber®

Test Clips Converts BNC (m) cables to

Minigrabber® test clips for test versatility 20AWG wire

Coaxial Cable Assemblies 2249-C: BNC (m) on 50 Ohm

RG58C/U with strain relief 2249-E:Rugged 75W BNC plug

to plug RG58C/U, 50 ohm cable makes

it ideal for most test andmeasurement applications, RF transmission systems andThinnet LAN applications

MPN # Description 2249-C-12 Assembly, 12”2249-C-24 Assembly, 24”2249-C-36 Assembly, 36”2249-C-48 Assembly, 36”2249-C-60 Assembly, 36”2249-C-72 Assembly, 72”2249-C-120 Assembly, 120”2249-E-24 Assembly, 24”2249-E-36 Assembly, 36”2249-E-72 Assembly, 72”

MPN # Description 6341 Probe Kit6275 Extra Tips

MPN # Description 5907A Test Lead Set6232A Electrical Probes

Precision Electronic ProbeKit with Replacement Tips The smallest package available

with a 1,000 volt rating Compatible with most Fluke,

Tektronix, Hewlett-Packard andMeterman meters Current 3 Amps Contains a pair (black/red) of

probes, and five sets of .040”dia. replacement stainless steeland gold plated tips

DMM Modular Test Set Plugs fit most popular DMMs

including Fluke and Meterman Silicone insulated 4’ leads Probes with 0.08” tip (6232A)

MPN # Description 4233-2 Minigrabbers4723-0 w/Jack, black4723-2 w/Jack, red5243-0 SMD Grabber black5243-2 SMD Grabber red

Minigrabber® Test Clips 4176 - 1 red/1 black minigrabbers®

4233 - 10 red minigrabbers®

4723 - Minigrabber® /banana jack 5243 - 10 SMD Grabbers®

MPN # Description 5519A Test Lead Set6262 Extended Tip

Replacement DMM TestLeadsMonolithic probes with fixed tips Durable .080” tips for long life Insulated 4’ leads fit most

popular DMMs including Flukeand Meterman Optional extended tip adapter

(6262)

MPN # Description 3782-24-0 Lead, 24”, black3782-24-2 Lead, 24”, red3782-36-0 Lead, 36”, black3782-36-2 Lead, 36”, red

Minigrabber® Test Clip toStacking Banana Plug Cord Banana plug is capable of vertical

and cross stackingMates to 1581 or any standard

banana jack

Minigrabber® Test ClipPatch Cords Ideal for providing temporary

jumper wires Provides excellent connector to

terminals and wire wrap posts Kit contains

10 pieces of 3781-24one of each colour

MPN # Description 5187-C-36 Test Clip

BNC (m) to Minigrabber®

Test Clips on RG58C/U BNC connector and breakout

wires are molded directly to thecable for added pull strength Grabber hook attaches to terminal

sizes up to .060" RG-58C/U

36” long wire

MPN # Description 3073 BNC (f) - plug4969 BNC (f) - lead4970 BNC (m) - lead

4233-0

4723-0

MPN # Description 3781-12-0 Lead, 12”, black3781-12-2 Lead, 12”, red3781-24-0 Lead, 24”, black3781-24-2 Lead, 24”, red3781-36-0 Lead, 36”, black3781-36-2 Lead, 36”, red5523 Patch Cord Kit

Electrical DMM Test Lead KitModular probe set with

standard tips Extended probe tip adapters Silicone 4 ft. leadsMedium alligator clip set Insulated spade lugs Large alligator clips

Insulation Piercing ClipsMake contact with insulated

wires without cutting or stripping insulation Spring loaded double V clamp

holds wire centered for piercing needle Pierces insulation on wires from

22 to 14 AWG (0.030" through0.180" diameter)

MPN # Description 6405/POM Piercing Clips

MPN # Description 5673B Test Lead Kit

Phone 1 866 663 8233


38

Micro SMD Grabber Test Clips Kit Kit includes: 12 grabbers (2 of each color)

black (72902-0), red (72902-2), yellow,green, blue and white. 6 black holding rods to reinforce

connection positions during side-by-sidemeasurements. model (72903)

MPN # Description 5677B Deluxe Multi-Use DMM Maxi-Kit5674C Deluxe Electronic DMM Test Lead Kit 159.75

Test Lead Kits 5677B includes: Test leads with a

right angle banana plugs, flexible test leads, retractable needle tip test probe, other probes, alligator clips and spade lugs. Interchangeable test probe tips allows for test versatility from general purpose to SMD applications. 5674C includes: Test leads with a right angle banana plugs, flexible test

leads, and insulated extended fine point adapter. Probe body, alligator,and test clip lead attaches directly to test leads for testing versatility

MPN # Description 1269 Coax Connector1296 Coax Connector1297 Coax Connector2451 Coax Connector3283 Coax Connector3285 Coax Connector3534 Coax Connector3778 Coax Connector3846 Coax Connector4054 Coax Connector4119-50 Coax Connector4297 Coax Connector4788 Coax Connector5319 Coax Connector4388 Triaxial Connector

1269

1296

2451

3285

3778

3846

4054

1297

3534

4788

3283

4119-50

5319

4388

4297

MPN # Description 2391 Aluminum Box

MPN # Description 5748 Adapter Kit72934 Adapter Kit

MPN # Description 72902 Test Clips Kit

Multi-RF Direct Adapter Kit Kit includes BNC (m)/Type N (f), BNC

(f)/Type N (m), TNC (m)/BNC (f),SMA(m)/BNC(m), SMA (m)/BNC (f), SMA (f)/BNC (m), SMA (f)/BNC (f), SMA(m)/Type N (f), SMA (f)/Type N (m), SMA(f)/Type N (f), SMA (m)/TNC (m), SMA(m)/TNC (f), SMA (f)/TNC (m), SMA(f)/TNC (f), SMA (m)/Type N (m), BNC (f-f),BNC (m-m), BNC (f-m-f) TEE, BNC (f-f-f)TEE, TNC (f-f) Adapter, TYPE N (f-f), TYPEN (m-m), SMA (m-f) Rt Angle, SMA (m-m),SMA (f-f), SMA Termination, 50W (m)

Maxi Universal Adapter Kit Kit contains two each: BNC (m), BNC (f),

TNC (m), TNC (f), SMA (m), SMA (f), N (m), N (f), UHF (m), UHF (f), Mini UHF (m), Mini UHF (f), F (m), F (f),RCA (m), RCA (f), six intermediatecouplers, one double Banana Plug, onedouble Banana Jack and one sampler.

Coaxial Connectors 1269: BNC (f) to Double Stacking Banana Plug 1296: BNC (m) to Stackable Binding Posts 1297: BNC (f) to 1/4in Phone Plug 2451: BNC (f) with 0.531" spaced

mounting holes 3283: BNC (f/f) Adapter 3285: BNC (f/m/f) Adapter 500V RMS 3534: BNC (f/m) Right Angle 3778: Isolated Ground Female

Bulkhead Receptacles - Teflon Insulation - 50 Ohms 3846: BNC (f/f) Adapter Isolated Ground 4054: BNC Male to Phono Jack 4119-50: BNC Feed-Thru Termination 4297: SMA (f) to Type N (m) Adapter 4788: R/A BNC, Brass 50Ω 5319: BNC Female To Phono Plug

- BNC Center Contact Nickel Plated 4388: Triaxial Connector Female

Bulkhead Receptacle

Jacks, Plugs & Posts 1581: Panel mount banana jack 1325: Solderless banana plug, stackable for banana jacks 1825: Solderless banana plug with collar 3276: Miniature banana plug with solder turretMDP-0/2: Double banana plug (-S w/ shorting bar) 5167: Banana jack for 18-20 AWG wire 5169: Banana plug for 18-20 AWG wire 3760: Standard binding posts 4995: Spring loaded binding posts with

silicone O-ring providing water resistant seal 4243: Binding posts with double mounting,

accepts standard banana plugs and 0.080in pin tips, wires and probe tips 3267: Uninsulated nickel-plated brass banana jack

1325-2

3760-2

4995-2

4243-0

3267

3276

MDP-S-2

1581-0

1825-0

5167

5169

MPN # Description 1581-0 Jack, black1581-2 Jack, red1325-0 Plug, black (pk.10)1325-2 Plug, red (pk.10)1325-02 DIY Plug w/screw1825-0 w/Collar, blk. (pk.10)1825-2 w/Collar, red (pk.10)3276 Miniature PlugMDP-0 Double plug, blk.MDP-2 Double plug, redMDP-S-0 Double plug, blk.MDP-S-2 Double plug, red5167 Banana Jack5169 Banana Plug3760-0 Binding Post, blk.3760-2 Binding Post, red4995-0 Binding Post, blk.4995-2 Binding Post, red4243-0 Binding Post, blk.4243-2 Binding Post, red3267 Banana Jack

“A” Size Die Cast Aluminum Box with Cover Connector A - BNC (m) Connector B - BNC (f) Finish: BBE

Phone 1 866 663 8233

39


Clip Lead Set Set of 10 18" clip leads with31mm insulated clips. 24 AWG stranded wires Colors: 2 red, 2 black,

2 green, 2 yellow, 2 white

MPN # Description 33-210-10 Clip Lead Set

MPN # Description PROBE100 Probe 100MHz

Probe 100MHz Complete oscilloscope probe set, for

measurements up to 100MHz Attenuation: 1:1 or 1:10 Conforms to IEC-1010 cat II


Electronic Test Lead Kit (CAT III-1000V) Two 42" (1m) PVC lead extensions with

shrouded banana plugs at both ends Two modular 4" (102mm) Heavy Duty test probe

handles with 0.16" (4mm) banana plug tip Two plunger mini-hooks Two alligator clips with removable insulators Includes storage pouch


MPN # Description TL805 Test Leads

Electrical Test LeadKit (CAT III-1000V) Two 40" (1m) PVC lead extensions with

shrouded banana plugs on both ends Two very sharp, extra long 0.3" (7mm) stainless

steel tipped plug-on test probes Two stainless steel flat tip

test probes (0.6"/15mm long) Two plunger activated retractable jaw

clips with a wide 0.75" (19mm) jaw opening

Double Injected Test Leads(CAT IV-600V, CAT III-1000V) Double coated PVC lead wire with white inner

layer to easily identify damaged leads Heavy duty chromium plated brass tips Shrouded, non-twist banana plugs for reduced

socket wear “Superflex” molded strain reliefs

for improved cable flexibility “D” shaped finger guards allow easy

access to narrowly spaced test points

Clip Lead Set Set of 10 heavy duty30" clip leads with50mm clips. 22 AWG Wires 5 different colors

MPN # Description 33-220-10 Clip Lead Set

Clip Lead Set Set of 4 heavy duty30" clip leads with50mm clips. 22 AWG Wires Colors: black, red,

yellow, white MPN # Description 33-230-4 Clip Lead Set

Oscilloscope Probes The IP series monolithic probes have switchable attenuation and are

available in 60 and 250MHz. These probes are ideal for technicians thatneed a basic oscilloscope probe The slimline design P and SP series probes are available in fixed or

switchable attenuation. These series of probes are perfect for thetechnician needing additional features such as replaceable cable andinterchangeable probe tip

Model Bandwidth Attenuation Cable Input Impedance RiseLength R L Time

SP Series, SwitchableSP60B 60MHz x1 1.2M 1Meg 47pF 5.8ns

x10 10Meg 18pFSP100B 100MHz x1 1.2M 1Meg 47pF 3.5ns





SP250B

SP300B

MPN # Description MTP AL-52F Fused Test Lead

Fused Test Lead Probes tip for 2mm Terminal : 4mm banana plug Wire : PVC UL 1803 Length : 1100 +/- 300mm Braid copper wires : 170/0.08mm Temperature tolerance range: -40 degree ~ 105 degree C Fuse protection CAT IV 690V 0.5A

(size : 6 x 32 mm) EN 61010-031 CAT IV 600V 10A Includes alligator clips, fuses

Phone 1 866 663 8233

Testers Telecom & Datacom

40

Wire Tracer/ToneGenerator KitTrace communications andcoaxial cables Non-Contact probe audibly

identifies selected wire or cable Easily trace wires from source

to termination Adjustable sensitivity control

improves wire identificationand eliminates false detection Continuity test with audible

and visible indicators

Network Cable TesterContinuity Tester for twisted pair and F Typecoaxial cables Tests for shorts, opens,

miswires and reversals,EIA/TIA568A and 568Band 10Base-T. F connector for

troubleshooting CATVcoaxial installations. Tests installed wiring and

jumper cables, and cablelengths from 3 to 600ft

MPN # Description CT100 Network Cable Tester

MPN # Description TG30 Wire Tracer/Tone Generator Kit

MPN # Description CB10 Breaker FinderCB10-KIT Troubleshooting Kit

CB10 Circuit Breaker FinderLocates the 110V to 125VAC circuit breaker or fuse withoutturning off the power Bright Red and Green LED’s

indicates if receptacle is correctlywired or six fault conditions Push button GFCI test Audible and visual circuit

breaker indication Convenient storage position for

transmitter/receptacle testerElectrical Troubleshooting Kitincludes CB10, CT20 and DV20AC Voltage Detector/Flashlight

MPN # Description ET10 Receptacle TesterET15 Receptacle Tester

Cable Identifier/Tester KitTransmitter/Receiver enables oneperson to remotely identify up to 16 wiresMultiMeter functions include:

AC/DC Voltage and Current,Resistance, Diode, and ContinuityWire voltage check from 5 to 16VDC Low battery indicator (transmitter

and receiver) Complete with 16-line Transmitter,

MultiMeter/ Receiver, two 9Vbatteries, pouch case, and two AAA batteries

Remote & Local Continuity Tester Local continuity checking is accomplished

by a bright flashing LED and loud pulsatingbeeper Remote continuity with the

use of the remote probe Flashing remote probe - two lead,

bi-color (red/green) LED probe allows asingle user to identify up to three wires or cablesat a time

Great from Electricians and Helpers, Cable TV andAudio System Installers, Alarm Technicians,Plumbers, HVAC Installers etc.MPN # Description CT20 Toner & Probe Kit

MPN # Description CT40 Cable Identifier

Line SeparatorAC Line Splitter allows clamp meter to measure ACCurrent on a 2-wire or 3-wire power cord to 15A: Provides easy and safe measurements of current

without the need to cut off the plug and separatethe conductors x1 for direct readings, and x10 for actual readings

multiplied by 10 Also features a voltage check function

MPN # Description 480172 Line Separator

Receptacle Testers Tests for faulty wiring in 3-wire receptacles Lights indicate circuit condition Detects 5 wiring faults (ET15)

Phone 1 866 663 8233

41

Telecom & Datacom Testers

Mini-Pocket Tester The cable test detects DC continuity or

shorts using a loud audible tone andan easy to read LED The system has a DC generator/short

detector and a removable tonedetector that screws into the base Right angled Male push-on

connector for fast use Easy to replace long life type

23A, 12V battery Easy viewable DC short LED

LAN Tester with Remote 2-piece tester Transmitter/receiver can test of installed cables Tests individual wires – point to point 8 LED’s on each unit

MPN # Description 400-026 LAN Tester with Remote

Professional Grade Telephone “Butt-Set”This butt-set is an Eclipse exclusive. It has all of the features of much more expensivemodels by other manufacturers. Amplified speaker for both

TALK and MONITOR modes 12 position memory Last number redialMoisture and dust

resistant housing Profile allows easy holding

on shoulder for hands-free operation Best quality bed of

nails probes 9V battery included

MPN # Description 400-042 Butt-Set

Butt-Set Complies with IP54

Dustproof & Waterproof tests High impedance monitor Outer-lead voltage LED indicators On/off checking feature checks

out if telecom line is connected well Continuous polarity

LED indicators Hands-free two-way

conversation Tone and pulse operation Store twelve 16-digit

numbers in repeat dialer plus extra number store Last number redial PBX pause button

MPN # Description MT-8100 Butt-Set

MPN # Description 902-228 Toner & Probe Kit

Universal All-in One Toner & Probe Kit Locates cables quickly and easily Locates hidden cables Isolates the right cable or pair fast Overcome noise and save time Tone on live networks safely and effectively Verify conductor continuity with cable map Identify and troubleshoot cable services

RJ45/RJ11/USB and Coax

Outlet TesterThis electrical outlet tester tests standard andGFCI outlets for proper wiring polarity. With GFCI outlets

MPN # Description 400-030 Receptable Tester

Plug ‘N Test Use to trouble shoot 120 V AC grounded

outlets and test GFCI receptacles Light sequence indicates correct/incorrect

wiring

MPN # Description GT-10GFI Plug ‘N Test

Multi-Network CableTester w/Remote LAN Tester w/RemoteWorks with CAT5

Installations RJ45 and BNC

Capability Auto Scanning

MPN # Description 400-001 Multi Network Cable Tester

Fiber Optic Power Meter Use of InGaAs photodiode

and flat response curve Function: dBm, dB, W. Extra function, low battery

indication, overloadindication, auto power off, LCD backlight.

MPN # Description MT-7600 Fiber Optic Power Meter

LAN Data Installers Kit Ratchet modular plug crimper, punchdown toolw/110 and 66 blades, LAN cable tester, UTPstripper, assorted plugs & boots and case

MPN # Description 500-021 LAN Data Installers Kit

MPN # Description NT-302 Mini-Pocket Tester

Phone 1 866 663 8233

Testers Telecom & Datacom

42

MPN # Description MTP 181-CB Circuit Tracer

Circuit TracerThe combination of amplifier probe and tonegenerator identifies and traces wires or cables Volume control for increased sensitivity Recessed on/off

button prevents battery drain Built-in

telephone plug Plug receptacle is

provided for headset or headphone Ideal for use with

telecommunication cable

MPN # Description MTP 190-CBI Circuit Identifier

Circuit Breaker IdentifierThe combination or transmitter and receiverlocates and identifies circuits, fuses or breakers

For use with circuits of 100 to 125 VACWorks on

live circuits Identifies proper

breaker with audible tone

MPN # Description LS-100 Line Splitter

Line Splitter Line splitter for most

clamp-ons eliminatesthe need to splitelectrical cords or openelectrical boxes for currentmeasurements on 120 V lines

LAN ProNavigator™ Tester Test data & telephone cable forproper pairing for EIA/TIA-568A & B, Token Ring,10 Base T & commonCat5, Cat5en and Cat6configurations. Also tests continuityof 50 & 75 ohm coaxial cables with BNCterminations.

MPN # Description 1543 LAN ProNavigator™ Tester

LAN and Telecom Testing Kit Combination RJ45 LAN tester and telephonetest set/tone probe cable tracer all-in-one. Identify pin outs, opens, shorts and crosses Test line polarity, provide talk power

and 4 tone generator patterns Includes case, patch cords, clips and batteries

PC Cable-Check™ Pro This universal tester mapscables, detects goodconnections, opens, shorts or crosses. Operates with over 20

types of cables including:LAN & telephone, serial, coaxial, USB, VGA, mini-USB, S-video, FireWire,PS/2 keyboard & parallelprinter Auto scan or manual

scan modes MPN # Description 1577 PC Cable-Check™ Pro

Data/Link ID and Cable-Check™ Tests UTP, STP & flat satin

cables with RJ45terminations Tests data & phone

connections Identifies

data & link transmissionspeeds Detect PC (NIC)

and HUB datatransmissions and link pulse

MPN # Description 1576 Data/Link ID and Cable-CheckTM

LAN & A/V Cable-CheckTM

Tests RJ45 patch cords and networkinstallations to identifygood connections, opens,shorts or cross-connections Connection type: RJ45

UTP or STP modular plug & cable TV "F"coaxial Identifies data &

telephone connectionschemes Tests continuity of cable

TV cables and installedcable runsMaps cable pin-out Automatic scanning

MPN # Description 1573 LAN and Telecom Testing Kit

MPN # Description 1594 LAN & A/V Cable-CheckTM

TRIPLETT

Line Bug 4 Phone/LAN Line Tester Tests standard telephone jacks

and LAN jacks for connection to telephone system Checks LAN Lines (RJ-45)

wired to 568 A/B standard for damaging telephone line current Has both RJ-11 and

RJ-45 style plugs 4 Tri-color LEDs indicate

Current, Polarity, & Ringing/AC Voltage on each line Tests Single Line, 2 Line,

3 Line, or 4 Line jacks to USOC (telephone) standard

MPN # Description 9615 Line Bug 4 Phone/LAN Line Tester

Phone 1 866 663 8233

43

Telecom & Datacom Testers

Audio Cable TesterEnables quick and convenient continuity cable testing for all types ofaudio cables continuity test function (buzzer and LED indication) Suited for the following connectors and their combinations:

6.3mm jack, 3.5mm jack, XLR 3P (M/F), XLR 5P (M/F), phono/RCA, banana plug, Speakon® 8P, Speakon® 4P, DIN 3P / 5P / 7P / 8P and 5-pin mini DIN

MPN # Description VTTEST15 Audio Cable Tester

200EP Inductive AmplifierUsed in conjunction with any tone generator, Inductive Amplifiers permits wire and cable identification without having to make direct metallic contact with the conductor.Features a powerful speaker for noisy environments, recessed on/off

button control and high gain for accurate wire identification incongested cable bundles and equipment rooms

Also includes adjustable volume control for precise identification, anLED for visual signal strength indication

MPN # Description 08671 200EP Inductive Amplifier

77HP Tone GeneratorPermits technicians to identify the conductorwithin a bundle, at a cross-connect point orat the remote end. Can be used on twisted pair wiring

(telecom, datacom, etc.), singleconductors, coaxial cables, de-energizedAC wiring and most other wiring

MPN # Description 77HP-G 77H Tone Generator

Professional Tone and Probe KitDesigned for the professional, this kit is for use on single conductors, twisted pairs, coax cables and de-energized electrical wiring.Housings are

drop-tested to ensure durability.

Includes the 77GX Tone Generator and 200GX Inductive Amplifier in a rugged carrying case

MPN # Description 60558 711K Professional Tone and Probe Kit

IntelliToneTM Toner & Probe Series

IntelliToneTM technology is a smart signal-toning and signal interpretationprocess that rapidly identifies and precisely zeroes in on even the mostelusive cables.

Ends cable location confusion, rejectsnoise and false signals Locates cable quickly from a

distance, even on an active network Isolates cable and wiring precisely

from a bundle, despite cable bleed Validates twisted-pair installation with

visual end-to-end Cablemap (opens,shorts, and reversed pairs)

MPN # Description MT-8200-50A IntelliToneTM 100 Toner and Probe KitMT-8200-51A IntelliToneTM 100 TonerMT-8200-53A IntelliToneTM 100 ProbeMT-8200-60A IntelliToneTM 200 Toner and Probe KitMT-8200-61A IntelliToneTM 200 TonerMT-8200-63A IntelliToneTM 200 ProbeMT-8202-05 IntelliToneTM CaseMT-8203-20 IntelliToneTM Test Leads w/Bed of NailsMT-8203-22 IntelliToneTM Test Leads w/Alligator Clips

MicroMapper

Fast, comprehensive LAN Wiremap checker.

Tests twisted-pair cables for open circuits,shorts, crossed pairs, reversed pairs, andsplit pairs Easy-to-read fault display Tone generator for tracing installed cables

hidden in walls, floors or ceilings For use with the MicroProbe Shield integrity testing Remote unit enables one person testing of

installed cables

MPN # Description MT-8200-49A MicroMapper

Phone 1 866 663 8233

Punchdown Tools Telecom & Datacom

44

Punchdown Tool - Deluxe Quality BIX Heavy duty quality BIX terminal block crimp tool with built in cutter Features Impact/Non-Impact adjustability with Hi/Lo settings Ergonomically designed with soft rubber grips

MPN # Description CT-225 Punchdown Tool

MPN # Description CT-228 Punchdown Tool - BIXCT-229 Punchdown Tool - 110

Test Clip for Bix Block For BIX17C

MPN # Description PH610A Test Clip for Bix Block

MPN # Description CP-3148 Punchdown Impact Tool w/110 onlyCP-3150 Punchdown Impact Tool w/110 & 66 blades

MPN # Description 3580 Non-Impact Punchdown Tool w/110 Blade3582 Non-Impact Punchdown Tool w/BixTM Blade

110 Non-Impact Punchdown Tool Terminates and cuts telephone and data wire into 88, 108, 109and 110 panels or jacks or Bix terminals. For insulation displacement (IDC) typebifurcated terminals. Solid or stranded, single insulation wire

3580

Bix Punchdown Tool Terminate cables, pigtails or jumper wires on all GigaBIX and BIX

connection products

MPN # Description PD-2A Bix Punch Down Tool

Punchdown Tool Impact handle, spring loaded, adjustable impact force High: 33 lbs. +/- 4 lbs, Low: 22 lbs. +/- 4 lbs Spare blade storage compartment

MPN # Description PD-1 Punch Down Tool 49.88

Punchdown Tool - BIX &110 Types Economy BIX terminal block crimp tool with built in cutter Economy 110 Krone type terminal block crimp tool with built in cutter Features Impact/Non-Impact adjustability

Punchdown Impact Tool Complete with 110 blade and 66 blade The rubber grip handle provides easy operation and user comfort Increased HI/LO impact forces to meet demands of all Category cables

through Cat 6

MPN # Description ENI-110 Non-Impact Punchdown Tool

Non-Impact Punchdown Tool Perfect for do-it-yourself small jobs on a 110 terminal block Fits neatly in the hand and performs with or without the cutter Simple - Fast - Easy

Phone 1 866 663 8233

45

Telecom & Datacom Networking Tools & Connectors

Single Box for Cat.5, 5E &Cat.6 Keystone Jack White

MPN # Description PH501 Single Box

Dual Surface Box for Cat.5,5E and Cat.6 Keystone Jack White

MPN # Description PH502 Dual Box

Inline coupler RJ-45 UTP

Cat5E F/F 8P/8P

Cat 6 Channel Level Keystone Jacks These jacks feature the ability to mount either

color-coded icon tabs for service identificationor dust covers to protect unused jacks form dust and other contaminants Other colours available on request

MPN # Description KJ458-C6C-IV Cat-6 Keystone Jack, IvoryKJ458-C6C-WH Cat-6 Keystone Jack, WhiteKJ458-C6C-BU Cat-6 Keystone Jack, Blue

Modular Joiner Jack to jack joiner

for connecting two cables

MPN # Description 12-203-1 6P/4C12-204-1 8P/8P12-204D-1 8P/8P (Data)

MPN # Description C609MJ 9Pin Male 6P/6C Mod. JackC809FJ 9Pin Female - RJ45 8P/8CC809MJ 9Pin Male 8P/8C Mod. JackC825FJ 25Pin Female 8P/8C Mod. JackC825MJ 25Pin Male 8P/8C Mod. Jack

Computer Module AdaptorsWith long screws

LongDistanceHDMI Wall Plate 1 Passive Input Wall Plate 1 Active Output Wall Plate Uses RJ-45 Cat5e or Cat 6 Cat5e good to 115 Feet, Cat-6 good to 260 Feet No External Power Required

MPN # Description KRJ45S Inline Coupler

MPN # Description 32-1867 HDMI Long Distance Wall Plates

Patch PanelsThese patch panels are fully preloaded and will mount on any standard 19"TIA/EIA compliant equipment rack. The Panels are connected using thestandard 110 punchdown type terminals and accommodate T568A &T568B wiring configurations. The ports (RJ45 modular jacks) are also compatible with RJ11/RJ12 plugs for applications where both voice and data are run into the same box or location. Available in

CAT5E or CAT6:

MPN # Description - CAT5E100-610 10" CAT5E 12 Outlet Patch Panel, 1.75" H - Wall mounted *100-612 19" CAT5E 12 Outlet Patch Panel, 1.75" H100-624 19" CAT5E 24-Outlet Patch Panel, 1.75" H100-648 19" CAT5E 48-Outlet Patch Panel, 3.5" H*100-610 not compatible with 19" racksMPN # Description - CAT6100-710 10" CAT6 12 Outlet Patch Panel, 1.75" H - Wall mounted *100-712 19" CAT6 12 Outlet Patch Panel, 1.75" H100-724 19" CAT6 24 Outlet Patch Panel, 1.75" H100-748 19" CAT6 48 Outlet Patch Panel, 3.5" H*100-710 not compatible with 19" racks

Hinged Wall BracketsFor use with standard 19" rackmount patch panels and components with 2U (two rack spaces / 3.5" high). Black powder coatedfinish with cut outs for cable pass through.MPN # Description100-682 Hinged Wall Bracket, 3.5" Height with 6" Depth100-685 Hinged Wall Bracket, 3.5" Height with adjustable 9-13.5" Depth

Wall Mount BracketsThe most cost effective method for wall mounting patch panels. For use with standard 19" rackmount patch panels and components with 1U (one rack space / 1.75" high). Plastic with side cable pass through.

MPN # Description100-691-2 Patch Panel Wall mount Brackets, 1.75" Height with 2.375" Depth, Pkg/2

Phone 1 866 663 8233

Networking Connectors Telecom & Datacom

46

RJ45 Keystone Jackfor Cat.5 White

RJ45 Keystone Jack for Cat.5 Includes 110 style

IDC termination White

MPN # Description PH500 Cat.5 JackPH500-5PK Cat.5 Jack x5

Modular Plug to LugExtension CordModular plug end for use with

modular jacks, colour coded 4-lugend for standard telephone wireattachments 25’ length

MPN # Description PH100-25 Extension Cord

Modular Plug to PlugExtension CordModular plug to modular plug.

Works with all modular telephoneinstruments and modular jacks 15” or 25’ length

MPN # Description PH101-15 Ext. Cord 15’PH101-25 Ext. Cord 25’

MPN # Description PH500E Cat.5 JackPH500E-5PK Cat.5 Jack x5

RJ12 Keystone Jack forCat.3 Telephone White or almond

MPN # Description PH510-WH White JackPH510-AL Almond Jack

Single Hole Wall Plate forCat.5, 5E, 6 Keystone JackWhite or

almond

MPN # Description PH503-WH White PlatePH503-AL Almond Plate

Two Hole Wall Plate forCat.5, 5E, 6 Keystone JackWhite or

almond


Three Hole Wall Plate forCat.5, 5E, 6 Keystone JackWhite or

almond


Modular Plug to Single JackExtension Cord 25’ length – 4 pin


Modular Plug to DuplexJack Extension Cord 12’ length


Modular “Y”Duplex Adaptor 4, 6 or 8 pin

MPN # Description PH106-4 Adapter 4 pinPH106-6 Adapter 6 pinPH106-8 Adapter 8 pin

Handset Detangler Twist free adaptor Black or ivory

MPN # Description PH130/BK Black DetanglerPH130/IV Ivory Detangler

ADSL –Line Filter

MPN # Description PH133 Line Filter

Flush MountWall Jack 4 pin White

MPN # Description PH127-4W-1 Jack

Modular In-Line Coupler 4 or 8 pin

MPN # Description PH107-4 Coupler 4 pinPH107-8 Coupler 8 pin

Modular Plug Use with flat modular

telephone wire 8 pin 100 per pack

MPN # Description PH114-8 Plug 8 pin

Modular Surface Jack withConnect Block Assembly Snap on cover,

self adhesive White 4, 6 or 8 pin

MPN # Description PH119-4 Jack 4 pinPH119-6 Jack 6 pinPH119-8 Jack 8 pin

5 Modular Jack Assembly 6” extension cord

MPN # Description PH120 Assembly

Modular Telephone Plugs Telephone plugs

with 15m" gold plated contacts

MPN # Description 12-253-10 4P/4C12-254-10 6P/4C12-256-10 6P/6C12-256R-10 6P/6C (Round)12-258-10 8P/8C12-258R-10 8P/8C (Round)12-258S-10 8P/8C (Solid)50 packs also available

Cat-5 Plugs For round jacket/

solid conductorcable

MPN # Description 13-101-5 30m” Gold50 packs also available

Phone 1 866 663 8233

Section 1 - Active Tech Electronics · Frequency 50 kHz 1 MHz 1 MHz 200 kHz 200 kHz 100 kHz 100 kHz 100 kHz 100 kHz ... life: 400 hours typical, without backlight ... HVAC Multimeter

Text of Section 1 - Active Tech Electronics · Frequency 50 kHz 1 MHz 1 MHz 200 kHz 200 kHz 100 kHz 100 kHz...

Agilent E5061B Network Analyzer 5 Hz to 3 GHz100 kHz to 1 MHz, IF bandwidth = 3 kHz 90 dB 1 MHz to 3 GHz, IF bandwidth = 3 kHz 95 dB 5 Hz to 100 Hz, IF bandwidth = 2 Hz 90 dB 100 Hz

(25 kHz) (8.33 kHz) 122.305 126 - flightplanner.de · Celle ETHC 118.250 MHz 118.255 20.12.2018 Celle-Arloh EDVC 123.650 MHz 123.655 25.10.2018 Cham-Janahof 130.125 MHz 122.365 01.11.2018

Template BR_Rec_2005.dot€¦ · Web view20-1 200 MHz 320-500 MHz 5-80 kHz (ocean) or 1-4 MHz (land) 14 MHz 300 kHz Transmit peak power (W) 1 500-7 600 20 100-5 000 600 1 000-1 500

Keysight Technologies N4985A System Amplifiers...Keysight Technologies N4985A System Amplifiers Data Sheet N4985A-S30 100 kHz to 30 GHz N4985A-S50 100 kHz to 50 GHz N4985A-P15 10 MHz

電界強度測定 - pages.anritsu-jpresponse.com...ML428B 9 kHz ～ 30 MHz ML524B メジャリングレシーバ 25 MHz ～ 1000 MHz MS2711E/MS2712E/MS2713E 9 kHz ～ 3 GHz/4GHz/6GHz

For DX Enthusiasts - KENWOOD · Div.1 Div.2 19.2 MHz 100 MHz 3218.112 MHz 22.348 MHz 1st local oscillator frequency ± 0.1 ppm TCXO Frequency Offset [kHz] Blocking Dynamic Range 1

Use of PWM and ADC on MC56F84789 to Drive Dual … · The PWM modulo to generate 10 kHz is derived from the 100 MHz clock. Thus, the modulo is 100 MHz / 10 kHz = 10,000 ticks. The

Introducción a CP1H - infoplc.net€¦ · Contador de Alta Velocidad: 4 ejes Fase simple: 4 x 100 kHz Fase diferencial: 4 x 50 kHz Fase simple: 2 x 1 MHz + 2 x 100 kHz Fase

Single-Chip Low Power RF Transceiver for Narrowband ...108 216 kHz kHz in 402 - 470 MHz range in 804 - 940 MHz range 108/216 kHz is the maximum guaranteed separation at 1.84 MHz reference

MHz min 40 dB at 20 MHz 205 kHz I MHZ 10 MHz min dB at kHz … · 2020-04-02 · 205 Dati tecnici Technical data kHz I MHZ 10 MHz min dB at kHz min 59 dB MHz min 50 dB at4 MHz min

Documentos escaneados de OneTouch 4 TL LP 675-2014.pdf · FM: 87,4 MHz a 108 MHz, aso de sintonización 100 kHz. AM: 530 kHz a 1.610 kHz, paso de sintonización 5 kHz 3,3+1-0, IV

20 Hz to 300 kHz/500 kHz/1 MHz Data Sheet - Micom

AR-DV1 - AOR, U.S.A · PDF fileAR-DV1 Multi-mode Digital Voice Receiver SPECIFICATIONS Frequency range: 100 kHz ~ 1300* MHz (Note: Specifications guaranteed above 530 kHz) Number of

Crystal Oscillator (XO) 100 kHz to 250 MHz

Hioki IM7580E2 Datasheet · IM7583, IM7585 IM7580A, IM7581 Measurement frequency 1 GHz Measurement frequency 500 MHz Measurement frequency 200 kHz Measurement frequency 100 MHz Signal

MC33272A - Operational Amplifiers, Single Supply, High Slew … · • High Gain Bandwidth Product: 24 MHz @ 100 kHz • High Slew Rate: 10 V/ s • Power Bandwidth: 160 kHz • Excellent

Spectrum Analyzerintpro.co.uk/wp-content/uploads/2015/02/IPS-Oscor-Green... · 2015. 6. 22. · 1 Audio: 200 kHz, 12.5 kHz, 6.25 kHz, 2 kHz 2 Video: 12.75 MHz, 6.375 MHz REAL-TIME

AN4736 Application note · • MSI: 100 kHz to 48 MHz multi-speed internal RC oscillator clock • PLL: 500 kHz to 80 MHz phase-locked loop that is clocked by HSI16, MSI or HSE oscillators

Mini Lathe EMI Test Results - ajawamnet.com · VB|/d INT REF STOP MHz 21 MHz, -45b MHz, -548 -536 -548 Marker 2 Marker . co REF -250 5 -45 START KHz Marker l: KHz Lathe 50 KHz ATTEN

HP 8901B Modulation Analyzer 150 kHz - 1300 MHz

DATA SHEET ASA15sdr.eladit.com/ACCESSORIES/ASA-15/datasheet asa15.pdf · Intermodulation level test (RF in -16 dBm; Gain High; f 100 kHz) Frequency (MHz) OIP3 (dBm) 9 KHz to 30 MHz

bus 05 03 12 - 2M KABLO€¦ · Zayıflama (Max. dB/100m) 9.6 KHz 0.3 38.4 KHz 0.4 200 KHz 0.5 625 KHz 0.9 1.25 MHz 1.2 4 MHz 2.2 16 MHz 4.2 100 MHz 12.3 Kullanım Alanları Bu kablo

El Espectro Radioeléctrico - IFT · Espectro radioeléctrico 3,000 GHz Infrarojo Luz visible Rayos x VLF 3 kHz 30 kHz 300 kHz 3 MHz 30 MHz 300 MHz 3 GHz 30 GHz 300 GHz LF MF HF VHF

Service Manual - oudio.nl · 550 1500 550 1500 550 1500 kHz kHz kHz kHz kHz kHz 158 , 5kHz S21 , C21 , SIT, C19, S15' C18, 340 1,72 ... 500 Hz. 10,7 MHz frequentie zwaai 200 kHz

500 kHz/1 MHz LCR Meter - Amazon Web Services€¦ · Models: 894, 895 500 kHz/1 MHz LCR Meter USER MANUAL

communications technology.. magazine Radio... · 2019-07-17 · (1 0 KHz-540 KHz, 100 KH-29.7 ~Hz, 0.54 , mHz to 54 mHz); single or dual diversity. In cabinet or rack mounted units

E5061B ENA Vector Network Analyzer - Keysight...2020/10/06 · 100 Hz to 9 kHz,10 Hz IF bandwidth 100 dB 9 to 100 kHz, 10 Hz IF bandwidth 110 dB 100 kHz to 1 MHz, 10 Hz IF bandwidth

ATEX & IECEx CERTIFIED SOLUTIONS RFID Identification in ...ATEX & IECEX CERTIFIED HIGH PERFORMANCE FIXED READERS 13.56 MHz MIFARE ®13.56 MHz LEGIC 125 kHz 125 kHz + 13.56 MHz HYBRID

FM Stereo/SW/MW/LW PLL Synthesized Receiver · 2018. 11. 15. · FM: 76 MHz – 108 MHz SW: 1 621 kHz – 29 999 kHz MW: 530 kHz – 1 620 kHz* LW: 150 kHz – 529 kHz Refer to the

For DX Enthusiasts · 2.7kHz 6kHz 15kHz ATT PLL PLL VCO Div.1 Div.2 19.2 MHz 100 MHz 3218.112 MHz 22.348 MHz 1st local oscillator frequency ± 0.1 ppm TCXO Frequency Offset [kHz]

Documents

Section 1 - Active Tech Electronics · Frequency 50 kHz 1 MHz 1 MHz 200 kHz 200 kHz 100 kHz 100 kHz 100 kHz 100 kHz ... life: 400 hours typical, without backlight ... HVAC Multimeter

Text of Section 1 - Active Tech Electronics · Frequency 50 kHz 1 MHz 1 MHz 200 kHz 200 kHz 100 kHz 100 kHz...