drylin W Proﬁle guides - igus · drylin® W Proﬁle guides Easy installation ... aluminium is used as rail material and provides ... Metal sheet cladding max. 200 ¡C

785

drylin® W Profile guides

Easy installation Dry running operation Variable carriage lengths Different rail widths available Low profile Corrosion free

786 7873D-CAD files, prices and delivery time www.igus.eu/drylinWLifetime calculation, configuration and more www.igus.eu/drylinW

drylin® W | Profile guides | Product overviewdrylin® W | Profile guides | AdvantagesLubrication free, light, quiet, long service life, low cost Profile guide systems for almost unlimited design freedom

Lubrication free linear system – drylin® Wdrylin® W profile guides are a cost-effective sy-stem. The design allows extremely high flexibility in the construction and installation thanks to the use of individual or double rails. Hard-anodised aluminium is used as rail material and provides the best friction and wear results. With its dry running lubrication free operation, the profile guide system is extremely resistant to dirt; the cleanliness also makes the system suitable for cleanroom and hygiene applications.

Easy installation, maintenance free Resistant to dirt thanks to dry operation Lightweight and quiet Square rail with floating bearing function for 90 degree installation

Bearing with manual clearance adjustment available

Typical application areas Agricultural machinery Vehicle construction Medical technology Facade construction Packaging industry Furniture Robotics Metal sheet cladding

max. 200 °C (depending on material)min. -40 °C

Carriage lengths: 60-250 mmCarriage widths: 54-195 mmRail length: up to 4000 mm

Detailed technical data www.igus.eu/drylinW

Available from stockDetailed information about delivery time online.

Online product finder www.igus.eu/drylin-finder

Component parts:Single rails and bearings

Liners made from iglidur® J200/J/X/E7/A180 Single bearing made from die-cast zinc, aluminium or stainless steel

Turn-to-fit function Rail material: hard-anodised aluminium or stainless steel

Individual rails for optimum design flexibility (individual/parallel/diagonal designs possible) From page 794

Assembled systems: Complete carriages and double-shaft profiles

Variable carriage lengths and widths Pre-assembled carriages available Mono-slide carriages for rapid assembly Rails/carriages for camera slider Rail material: hard-anodised aluminium Torsion-resistant double-shaft profile Parallel shaft guides reduce alignment and installation time From page 804

Accessories Manual clamp as single bearing as well as integrated into complete carriages

End caps for high profile rails From page 812

Hybrid guides Roll and slide Low driving forces Bearing with single or double roll Complete carriage with hybrid function Suitable for combination with drylin® single and double shaft profiles From page 817

Measurement systems based on drylin® W From page 957

Linear modules based on drylin® W SLW/SAW/GRW/ZLW From page 1081

Superior operating properties by combining iglidur® bearing ele-

ments, anodised rails and round shaft profiles

Corrosion resistant

Quiet operation

Clean as no lubrication required

Profiles with various geometric designs, installation

sizes and clearances

Lightweight due to the use of plastics

and aluminium

Smooth running thanks to sliding elements made from lubrication

free iglidur® high performance polymers

Maintenance free


drylin® W | Profile guides | Online toolsdrylin® W | Profile guides | Application examples

Quiet, low vibration adjustments in the stage tech-nology field are enabled through the use of drylin® W linear guide systems based on steel shafts in combi-nation with stainless steel housing bearings.

Due to the price advantage coupled with the resist-ance against dirt and dust, the customer opted for drylin® W.

Adjustment mechanisms on gym equipment no longer have to be maintained thanks to the igus® drylin® W profile guides.

drylin® linear bearings enable precise positioning at high speeds. Unlike conventional bearings, they do not require lubrication and are corrosion free.

With a low weight through the use of plastic and al-uminium with a corrosion free coating, the guides in the drylin® range impress with their quiet and precise running.

The closing mechanism on this casting machine is subjected to high temperatures and dirt. To make it as durable as possible despite this, it is mounted with a drylin® W profile guide.

Several online configurators are also availa-ble for drylin® W linear guide systems. These help you to calculate the function and service life, and provide you with support when integrating the selected linear guide into your 3D model. The desired version of the drylin® W li-near guide system can be ordered in the online shop with just a few clicks. Shipment is made within 24-48 hours!

www.igus.eu/drylinW-configurator

The examination of your application as well as the calculation of the expected service life, these are the duties of the calculation programme dry-lin® expert 2.0. Only 4 steps are required to obtain a definitive result regarding the operating behaviour of the application, as well as a host of important tech-nical parameters, such as the expected wear and the required drive forces.

www.igus.eu/drylin-expert

The igus® CAD online configurator gives you the ability to design and save your linear guide as a system, individual components directly as a 3D model in all commonly used formats, or to have these sent by e-mail – free of charge and without registration.

www.igus.eu/drylin-CAD

6 10 16 20 25 J J200 X A180 E7


drylin® W | Profile guides | Technical data | Floating bearingsdrylin® W | Profile guides | Product selection

Properties

Size Liner material

Housing bearing, round

Housing bearing, square

Fitted carriage, round

Fitted carriage, square

Mono-slide carriage

Bearings/carriages

Housing material Options

Zinc Die-cast Aluminium Stainless steel Manual clamp Clearance

adjustment Hybrid Ø 10 mm slider

Floating be-aring





Mono-slide carriage

Rails

Rail material Fastening options

Aluminium Stainless steel Holes 3/8" thread Clamping element Slot nuts

Single rail, round

Single rail, square

Double rail, round

Double rail, square

High profile, round

High profile, square

Combinations

Single rail Double rail High profile rail

square round square round square round





Mono-slide carriage

±0.2

±1.0

Floating bearings aid assembly – when using single railsAssembly is easy with the drylin® WQ square profile. Floating bearings for all directions (±1 mm) compensate misalignments and parallelism errors between rails. This eliminates jamming, otherwise only prevented by timeconsuming parallel alignment of the system. Although drylin® W is a profile rail system, it is able to compensate angular errors about the x-axis. An angular adjustment of ±7 ° is possible here. This effectively eliminates the misalignment known to occur when fitting to sheet metal fabrications.

Possible combinations in assembled rail systems Available floating bearing blocksFixed bearing Floating bearing

Fixed bearing Floating bearing

Fixed bearing Floating bearing

rotating - square

LLZ - square

LLY - square

LL - round

Floating bearings for all directions (up to ±1 mm) compensate misalignments and parallelism errors.

±7°

±1.0

±0.2

• = S

tand

ard

liner

iglidur®

Jiglidur®

J200iglidur®

Xiglidur®

E7iglidur® A180

•

•

• • • • •

• • • • •

• • • • •

• • • • •

•

•

•

• • • • •

•

•

•


Suitable liners

Available housing bearing & carriages


Standard

Aluminium


Standard

Stainless steel

Aluminium

Aluminium, tandem

"Turn to fit"

Hybrid – roll and slide

Guide carriage, fitted

Standard, assembled, square

Standard, assembled, round

Hybrid, round

"Turn-to-fit", round

Complete carriages

Mono-slide square

Lubrication free iglidur® high performance polymers

Form-fit torque resistance

Low friction, low wear

Vibrations dampening

Open geometric design for rapid assembly

Resistant to dirt

Sliding surface structures with integrated flute design

for dirt to pass through

Axial retention

Corrosion resistant

drylin® liners made from high perfor-mance polymersExtremely wear-resistant tribopolymers improved by precisely blended additions of strengthening materials and solid lubricants, tested a thousand times and proved a million times – that is iglidur®. Further to the general properties, every iglidur® bearing material has a series of special features, which account for its particular suitability for cer-tain applications and requirements. The detailed description of the materials can be found in the respective sections.

Lubrication free Corrosion resistant Low coefficients of friction Maintenance free Dirt resistance Lightweight High wear resistance Excellent price-performance ratio

•= Standard •= Optional

drylin® W | Profile guides | Linersdrylin® W | Profile guides | Liners

The "All-rounder" – iglidur® J

The specialist –iglidur® J200

The extreme –iglidur® X

The marathon runner – iglidur® E7

FDA compliant –iglidur® A180

Application temperature -50 to +90 °C -50 to +90 °C -100 to +250 °C -50 to +90 °C -50 to +90 °C

Best coefficient of friction with Steel shaft Aluminium, hard anodised Steel hard chrome-plated Steel/Stainless steell shaft Stainless steel shaft

Volume resistance > 1013 Ωcm > 108 Ωcm < 105 Ωcm > 109 Ωcm > 1012 Ωcm

Moisture absorption 1.3 % weight 0.7 % weight 0.5 % weight < 0.1 % weight 0.2 % weight

Maximum life time Aluminium, hard anodised Aluminium, hard anodised Hardened stainless steel Steel/Stainless steell shaft Stainless steel shaft

Potential shaft material all shaft materials Aluminium, hard anodised Hardened stainless steel Steel/Stainless steell shaft all shaft materials

Permissible stat. surface pressure 35 MPa 23 MPa 150 MPa 18 MPa 28 MPa

Part No. JUM-... J200UM-... XUM-... E7UM-... A180UM-...

WSQ-06-3000 WJ200QM-01-10-LLY

WSQ-06WSQ-10WSQ-16WSQ-20

WJ200QM-01-06WJ200QM-01-06-LLZWJ200QM-01-06-LLYWJ200QM-01-06-ALWJ200QM-01-10WJ200QM-01-10-LLZWJ200QM-01-10-LLYWJ200QM-01-10-ALWJ200QM-01-16WJ200QM-01-16-LLZWJ200QM-01-16-LLYWJ200QM-01-16-ALWJ200QM-01-20WJ200QM-01-20-LLZWJ200QM-01-20-LLYWJ200QM-01-20-ALWSQ-06

WSQ-10WSQ-16WSQ-20

794 795

drylin® W | Profile guides | Product range drylin® W | Profile guides | Product rangedrylin® W profile guides

drylin® W profile guides

3D-CAD files, prices and delivery time www.igus.eu/drylinWLifetime calculation, configuration and more www.igus.eu/drylinW

Rai

l len

gth

[mm

]

Length

Order key – single railG

uide

rails

Sha

fts-

Ø

TypeS

quar

e

Part No. C4 C5 C5 C6 C6 K1 for screw

ly lz Wby Wbzmin. max. min. max.

DIN 912 [mm4] [mm4] [mm3] [mm3]

60 20 49.5 20 49.5 M458) 2,200 640 220 100120 20 79.5 20 79.5 M658) 16,100 3,300 950 350120 20 79.5 20 79.5 M8 33,000 10,800 1,700 910120 20 79.5 20 79.5 M8 56,500 34,000 2,600 2,100

C6 C4 C5

C3C1

G1

A3

G2

K1

L

Standard hole pattern: C5 = C6, please order with drawing for C5 ≠ C657) Height dimension minus the bearing clearance tolerance58) Plain holes

ha

B

K2

H

K3

h2

A1

da

zy x

! Coz-

WSQ-...

WJ200QM-01-...

Single rail, square, hard-anodised aluminium

Load data and dimensions [mm]

Hard anodised surfaces Page 764

Part No. Floating bearing

clearance

Floating bearing

direction

Weight B C1 C3 A3 K2 K3 Stat. load capacity Coy Coz+ Coz–

[g] [N] [N] [N]

– – 16 18 19 10 4.5 M4 M3 420 420 140± 0.5 z 16 18 19 10 4.5 M4 M3 420 420 140± 0.5 y 16 18 19 10 4.5 M4 M3 420 420 140

– – 8 18 19 10 4.5 M4 M3 420 420 140– – 41 26 29 16 6.5 M6 M5 1,200 1,200 250

± 0.7 z 41 26 29 16 6.5 M6 M5 1,200 1,200 250± 0.7 y 41 26 29 16 6.5 M6 M5 1,200 1,200 250

– – 21 26 29 16 6.5 M6 M5 1,200 1,200 250– – 100 34.5 36 18 9 M8 M6 2,100 2,100 400

± 1.0 z 100 34.5 36 18 9 M8 M6 2,100 2,100 400± 1.0 y 100 34.5 36 18 9 M8 M6 2,100 2,100 400

– – 51 34.5 36 18 9 M8 M6 2,100 2,100 400– – 190 42.5 45 27 9 M8 M6 3,200 3,200 500

± 1.0 z 190 42.5 45 27 9 M8 M6 3,200 3,200 500± 1.0 y 190 42.5 45 27 9 M8 M6 3,200 3,200 500

– – 104 42.5 45 27 9 M8 M6 3,200 3,200 500

Housing bearing, square, made from zinc or aluminium


Order example: WJ200QM-01-06 for a housing bearing, squareWJ200QM-01-06-LLZ for a housing bearing, square with floating z-directionWJ200QM-01-06-AL for a housing bearing, square, made from aluminium

OptionsLLY: Floating bearing

in y-directionLLZ: Floating bearing

in z-directionAL: Housing bearing

made from aluminium

Q2

Q1

h1

! Coz-

dryl

in® W

iglid

ur® b

earin

g m

ater

ial

OptionsSize

Order key – housing bearing

Floa

ting

bear

ing

in

y-di

rect

ion

Qua

ntity

, bea

rings

Hou

sing

bea

ring,

sq

uare

Siz

e

Type

Part No. Weight H57) da L a h h1 h2 G1 G2 A1 Q1 Q2

±0.25 –0.1 max.

[kg/m]

0.23 14 5 3,000 14 4 458) 7.5 18 10.5 13.5 17 150.54 20 7.5 4,000 25 5.5 5.558) 11 27 17 18.5 26 210.94 27 11.5 4,000 27 7.5 3.5 14 33 19 25 32 281.41 36 15 4,000 27 9.5 4.5 20 38 21 30 37 37

Can be combined with:

WSQ-... WSQ-... WSXQ-...


WJ200QM-...

WJ200UM-01-10-LL

WS-10WS-16WS-20WS-25

WS-10WS-16WS-20WS-25

WJ200UM-01-10WJ200UM-01-10-LLWJ200UM-01-10-ALWJ200UM-01-16WJ200UM-01-16-LLWJ200UM-01-16-ALWJ200UM-01-20WJ200UM-01-20-LLWJ200UM-01-20-ALWJ200UM-01-25WJ200UM-01-25-AL

796 797




Single rail, round, hard-anodised aluminium Housing bearing, round, made from die-cast zinc or aluminium



DIN 912 [mm4] [mm4] [mm3] [mm3]

120 20 79.5 20 79.5 M658) 19,000 2,850 1,000 310120 20 79.5 20 79.5 M8 36,000 12,900 1,800 940120 20 79.5 20 79.5 M8 57,100 35,000 2,700 1,900150 25 99.5 25 99.5 M10 129,000 86,000 4,900 3,800


Q2

Q1

h1di

! Coz-

A1

B

h

h2

H

K2

da di

a

! Coz-WJ200UM-01-..

WS-..

K3

C6 C4 C5

C3C1

G1

A3

G2

K1

L

zy x

This assembled position not possible for WS-10

Part No. Weight H57) da di L a h h1 h2 G1 G2 A1 Q1 Q2

±0.25 –0.1 max.

[kg/m]

0.62 18 10 – 4,000 27 5.5 5.558) 9 27 17 16.5 – –0.98 27 16 8.0 4,000 27 7.5 3.5 14 33 19 25 32 281.32 36 20 10.2 4,000 27 9.5 4.5 20 38 21 30 37 372.03 45 25 14 4,000 32 11.5 5.5 25 46.5 25.5 37.5 45.5 46

Standard hole pattern: C5 = C6, please order with drawing for C5 ≠ C657) Height dimension minus the bearing clearance tolerance58) Plain holes

Part No. Floating bearing

clearance

Weight B C1 C3 A3 K2 K3 Stat. load capacity Coy Coz+ Coz–

[g] [N] [N] [N]

– 41 26 29 16 6.5 M6 M5 1,200 1,200 250±0.2 41 26 29 16 6.5 M6 M5 1,200 1,200 250

– 20 26 29 16 6.5 M6 M5 1,200 1,200 250– 100 34.5 36 18 9 M8 M6 2,100 2,100 400

±0.2 100 34.5 36 18 9 M8 M6 2,100 2,100 400– 48 34.5 36 18 9 M8 M6 2,100 2,100 400– 190 42.5 45 27 9 M8 M6 3,200 3,200 500

±0.25 190 42.5 45 27 9 M8 M6 3,200 3,200 500– 99 42.5 45 27 9 M8 M6 3,200 3,200 500– 425 52.5 58 36 11 M10 M8 4,800 4,800 950– 250 52.5 58 36 11 M10 M8 4,800 4,800 950

Order example: WJ200UM-01-10 for a housing bearing, roundWJ200UM-01-10-LL for a housing bearing, round, floating bearingWJ200UM-01-10-AL for a housing bearing, round, made from aluminium


dryl

in® W

Line

r ig

lidur

® J

200

OptionsSize

Order key

Floa

ting

bear

ing

Num

ber o

f be

arin

gs

Hou

sing

bea

ring,

ro

und

Siz

e

Type

C3C1

A3B

H

K2 ! Coz-

K3


Stainless steel version available Page 800

Stainless steel version available Page 801

OptionsLL: Floating bearingAL: Housing bearing made from

aluminium


WJ200UM(T)-... WJ200UME-... WJUM-..-ES-FG WJRM-...


WS-... WS-..-ES-FG-... WS-... WS-...-ES-FG WSX-...

Suitable liner materials

iglidur® J iglidur® J200 iglidur® X iglidur® E7 iglidur® A180

WJ200UME-01-10WJ200UMT-01-10-AL

WJUME-01-10WJ200UME-01-16WJ200UME-01-20

WJ200UMT-01-10-ALWJ200UMT-01-16-AL

798 799




C3C1

A3B

H

K2 ! Coz-

K3

Order key

dryl

in® W

Line

r ig

lidur

® J

200

Sta

ndar

d

Siz

e

Type

Adj

usta

ble

Tand

em

Hou

sing

bea

ring,

ro

und

Hou

sing

bea

ring,

ro

und

dryl

in® W

Line

r ig

lidur

® J

200

Siz

e

Sta

ndar

d

Alu

min

ium

Order key

Type Size SizeOption

Part No. Weight B C1 C3 A3 K2 H SW G1 Stat. load capacityCoy Coz+ Coz–

[g] [N] [N] [N]

43 26 29 16 6.5 M6 18 1.5 27 560 560 250110 34.5 36 18 9 M8 27 2.5 33 980 980 460222 42.5 45 27 9 M8 36 2.5 38 1,500 1,500 500

C3C1

A3B

K2

K3

Part No. Weight B C1 C3 A3 K2 K3 Static load capacityCoy Coz+ Coz–

[g] [N] [N] [N]

43 26 58 45 6.5 M6 M5 2,400 2,400 50032 34.5 72 54 9 M8 M6 2,400 2,400 600

Technical data and dimensions [mm] Technical data and dimensions [mm]

Housing bearing, individual, tandem, round, anodised aluminium Housing bearing, individual, round, adjustable clearance

Allen key supplied






iglidur® J



WS-10-40-ES-FG

WJUM-01-10-ES-FG59)

WJUM-01-16-ES-FG59)

WJUM-01-20-ES-FG59)

WJUM-01-25-ES59)

WS-10-ES-FGWS-16-ES-FGWS-20-ES-FGWS-25-ES

WS-10-ES-FGWS-16-ES-FGWS-20-ES-FGWS-25-ES

WS-10-40-ES-FG

800 801




Single rail round, made from stainless steel V4A Round double rail and housing bearing, made from V4A stainless steel

Size 10-20Material for housing and shaft support 1.4408 (AISI 316)Shaft material 1.4571 (AISI 316Ti)Size 25Material for shaft, shaft support, housing 1.4571 (AISI 316Ti)

Technical data and dimensions [mm]

59) alternative with XUMO-01-... liners for high temperatures available. Part No. WXUM-01-...

Housing bearing round, made from stainless steel V4A


Part No. C4 C5 C5 C6 C6 K1 for screwmin. max. min. max.

DIN 912

120 20 79.5 20 79.5 M6


Part No. Weight B C1 C3 A3 K2 K3 Stat. load capacity Countersunk

head screwCoy Coz+ Coz-

[g] [N] [N] [N]

57 26 29 16 6.5 M6 M5 3,800 3,800 950134 34.5 36 18 9 M8 M6 6,900 6,900 1,450280 42.5 45 27 9 M8 M6 11,000 11,000 1,900564 52.5 58 36 11 M10 M8 16,000 16,000 3,600

57) Height dimension minus the bearing clearance tolerance 58) With plain holes

Part No. Weight H57) da L a h h1 h2 G1 G2 A1 Q1 Q2±0.25 -0.1 max. –0.3

[kg/m]

0.87 18 10 3,000 27 5.5 5.558) 9 27 17 16.5 - -2.22 27 16 3,000 27 12 4.5 14 33 19 25 32 283.37 36 20 3,000 27 16 8 20 38 21 30 37 375.21 45 25 3,000 32 11.5 5.5 25 46.5 25.5 37.5 45.5 46


ly lz Wby Wbzmin. max. min. min.

DIN 912 [mm4] [mm4] [mm3] [mm3]

120 20 79.5 20 79.5 M658) 491 491 98 98120 20 79.5 20 79.5 M8 3,217 3,217 402 402120 20 79.5 20 79.5 M8 7,854 7,854 785 785150 25 99.5 25 99.5 M10 19,175 19,175 1,534 1,534

Part No. Weight H57) da L a b h h2 A A2[kg/m] ±0.25 h9 max. –0.3

1.58 18 10 3,000 40 40 5.5 9 73 60

K1

K3

! Coz- ! Coz-

C3

C1

A3

G1

G2

C5 C4 C6

L

K2 B

A1 a h1

h h2 H

da

Q1

Q2

K1

K3

! Coz- ! Coz-

C3

C1

A3

G1

G2

C5 C4 C6

L

K2 B

A1 a h1

h h2 H

da

Q1

Q2

K3

! Coz-

z

yx

da

C6 C4 C5

K1

a

b

h H

K2

L

h2

C3

C1

B

A2

A

A3

K3

! Coz-

z

yx

da

C6 C4 C5

K1

a

b

h H

K2

L

h2

C3

C1

B

A2

A


WJ200UM(T)-... WJ200UME-... WJUM-..-ES-FG WJRM-...


iglidur® J iglidur® E7 iglidur® A180

57) Height dimension minus the bearing clearance tolerance

Material for housing and shaft support 1.4408 (AISI 316)Shaft material 1.4571 (AISI 316Ti)Size 25Material for shaft, shaft support, housing 1.4571 (AISI 316Ti)

WSX-06-30-4000

WSQ-06-30WSQ-10-40WSQ-10-80WSQ-10-120 WSQ-16-60WSQ-20-80

WSQ-06-30WSQ-10-40WSQ-10-80WSQ-10-120WSQ-16-60WSQ-20-80

WSX-06-30

802 803




Part No. C4 C5 C6 K1 for screw


DIN 912 [mm4] [mm4] [mm3] [mm3]

60 20 49.5 20 49.5 M558) 19,000 1,250 1,100 200120 20 79.5 20 79.5 M658) 71,600 5,580 3,000 610120 20 79.5 20 79.5 M658) 335,000 7,070 8,300 700120 20 79.5 20 79.5 M658) 1,175,000 8,000 18,400 760120 20 79.5 20 79.5 M8 324,700 20,500 9,400 1,700120 20 79.5 20 79.5 M8 1,145,000 75,300 23,600 4,500


Part No. Weight H57) da dr L a A1 b h h1 h2 G1 G2 a161) Q1 Q2

±0.25 –0.1 max.

[kg/m]

0.45 14 5 5 3.000 27-0,4 13.5 30 4 458) 7.5 22.5 15 – 21.5 150.92 20 75 6.7 4.000 36-0,5 18.5 40 5.5 5.558) 11 30 20 – 29 211.41 20 7.5 6.7 4.000 70-0,7 25.0 74 5.5 5.558) 11 27 17 40 26 212.02 20 7.5 6.7 4.000 116-0,7 18.5 120 5.5 5.558) 11 30 20 80 29 211.84 27 11.5 10.7 4.000 54-0,5 30.0 58 7.5 3.5 14 43 29 – 42 283.30 36 15 14.1 4.000 74-0,7 30 82 9.5 4.5 20 38 21 40 37 37


57) Height dimension minus the bearing clearance tolerance 58) Plain holes 61) WSQ-06-30/-10-40/-16-60 a single row of mounting holes down the centreline, WSQ-10-80/-10-120/-20-80

two parallel rows of mounting holes

zy x

/

E

&&

&

&&

.

*

*

$

GDGU

+

$ D

K

GD

%.

.

:-40

:64

4

4

K

K

E

& . &&

$

&

&

**

/

GDGU

.%

GD +K

.

$ D4

4K

D:64

:-40

Double rail, square, hard-anodised aluminium High profile rail, square, hard-anodised aluminium


B

C

s

K1

C3

C1

G1

H

da

di

a

hh2

A1b

nh

n

nb

X Y

nh n nb T X Y ly lz[mm4] [mm4]

7 - - M5 12 10 30,391 11,674

Part No. Weight H57) da di L a A1 b h h1 h2 s K1 C1 C3 G1

±0.25 –0.1 max.

[kg/m]

0.76 26 ±0.01 5 – 4,000 29.7 13.5 30 16 19.5 7.5 40 M5 19 10 20

Rai

l len

gth

[mm

]

Length

Order key

Hig

h pr

ofile

rail

Pro

file

rail

Sha

fts-

Ø

Rai

l wid

th [m

m]

Type

Order example: WSX-06-30: High profile rail, squareWSQ-06-30: Standard double rail, square


WJQM-... WW-... WWC-...


WJQM-... WW-... WWC-...


WWC-10-40-10WW-06-30-06

WWC-06-30-06WWC-06-30-08WWC-06-30-10WWC-10-40-10WWC-10-40-15WWC-10-40-20WWC-10-80-10WWC-10-80-15WWC-10-80-20WWC-10-120-10WWC-10-120-15WWC-10-120-20WWC-16-60-10WWC-16-60-15WWC-16-60-20WWC-20-80-15WWC-20-80-20WWC-20-80-25

WW-06-30-06WW-06-30-08WW-06-30-10

804 805




Part No. Weight A C A2 C2 K2 H257) Stat. load capacityWidth Length ±0.2 Coy Coz Mox Moy Moz

[kg] [N] [N] [Nm] [Nm] [Nm]

0.07 54 60 45 51 M4 16 1,680 840 25 34 340.09 54 80 45 71 M4 16 1,680 840 25 51 510.12 54 100 45 91 M4 16 1,680 840 25 68 680.21 73 100 60 87 M6 22 4,800 2,400 96 170 1700.32 73 150 60 137 M6 22 4,800 2,400 96 290 2900.42 73 200 60 187 M6 22 4,800 2,400 96 410 4100.28 107 100 94 87 M6 22 4,800 2,400 178 170 1700.42 107 150 94 137 M6 22 4,800 2,400 178 290 2900.56 107 200 94 187 M6 22 4,800 2,400 178 410 4100.36 153 100 140 87 M6 22 4,800 2,400 288 170 1700.54 153 150 140 137 M6 22 4,800 2,400 288 290 2900.72 153 200 140 187 M6 22 4,800 2,400 288 410 4100.41 104 100 86 82 M8 30 8,400 4,200 240 270 2700.61 104 150 86 132 M8 30 8,400 4,200 240 480 4800.80 104 200 86 182 M8 30 8,400 4,200 240 690 6900.99 134 150 116 132 M8 40 12,800 6,400 525 670 6701.33 134 200 116 182 M8 40 12,800 6,400 525 990 9901.66 134 250 116 232 M8 40 12,800 6,400 525 1,250 1,250


C2C

A2 A

H2

K2

C2C

A2 A

H2

K2

Mono-slide carriage, anodised aluminium

Order key complete system Page 972

Part No. Weight A C A2 C2 K2 H257) Stat. load capacity Width Length ±0.25 Coy Coz Mox Moy Moz

[kg] [N] [N] [Nm] [Nm] [Nm]

0.10 54 60 45 51 M4 18 1,680 840 25 34 340.11 54 80 45 71 M4 18 1,680 840 25 51 510.12 54 100 45 91 M4 18 1,680 840 25 68 68

C2C

A2 A

K2WW-06-30-...

H2

WJ200QM-01-06

WSQ-06-30

C2C

A2 A

K2WW-06-30-...

H2

WJ200QM-01-06

WSQ-06-30


Guide carriage, assembled, square

All parts can be ordered individually or as an assembled system Page 809

Order keyComplete system Page 972

Mon

o-S

lide

gu

ide

carr

iage

Gui

de c

arria

ge

Sha

fts-

Ø [m

m]

Sha

fts-

Ø [m

m]

Pro

file

wid

th

Pro

file

wid

th

Leng

th o

f car

riage

Car

riage

leng

th

TypeType SizeSize

Order example: WW-06-30-06: fitted guide carriageWWC-06-30-06: Mono-Slide guide carriage


WSQ-... WSXQ-...


iglidur® J


iglidur® J200



WSX-10-40-4000

WS-10-40WS-10-80WS-10-120WS-16-60WS-20-80WS-25-120

WS-10-40WS-10-80WS-10-120WS-16-60WS-20-80WS-25-120

WSX-10-40WSX-10-80WSX-16-60

806 807




WSX-10-80

WSX-16-60

Double rail, round, hard-anodised aluminium High profile rail, round, hard-anodised aluminium

Part No. C4 C5 C6 K1 for screw


DIN 912 [mm4] [mm4] [mm3] [mm3]

120 20 79.5 20 79.5 M658) 91,000 5,100 3,600 590120 20 79.5 20 79.5 M658) 388,000 6,100 9,200 650120 20 79.5 20 79.5 M658) 1,303,000 7,100 20,000 720120 20 79.5 20 79.5 M8 367,600 26,100 9,900 1,900120 20 79.5 20 79.5 M8 1,080,000 78,700 21,000 4,000150 25 99.5 25 99.5 M10 4,867,000 215,000 62,400 8,500


Part No. Weight H57) da di L a A1 b h h1 h2 G1 G2 a162) Q1 Q2[kg/m] ±0.25 max.

1.00 18 10-0,1 – 4,000 40-0,5 16.5 40 5.5 5.558) 9 30 20 – – –1.50 18 10-0,1 – 4,000 74-0,7 16.5 74 5.5 5.558) 9 27 17 40 – –2.02 18 10-0,1 – 4,000 120-0,7 16.5 120 5.5 5.558) 9 30 20 80 – –1.96 27 16-0,1 8.0 4,000 54-0,5 25.0 58 7.5 3.5 14 43 29 – 32 283.30 36 20-0,1 10.2 4,000 74-0,7 30.0 82 9.5 4.5 20 38 21 40 37 375.8 45 25-0,15 14.0 4,000 120-0,7 37.5 131 11.5 5.5 25 46.5 25.5 80 45.5 46

Technical data and dimensions [mm] Technical data and dimensions [mm]

57) Height dimension minus the bearing clearance tolerance62) WS-10-40/-16-60 a single row of mounting holes down the centreline; WS-10-80/-10-120/-20-80/-25-120 two

parallel rows of mounting holes

Standard hole pattern: C5 = C6, please order with drawing for C5 ≠ C658) Plain holes

C4

C6 C5C3

C1

L

A3

G1

G2

b K1

h

Q2

Q1

di

! Coz-

Bz

a

H

K2 di

A1

h2

a1

dah1

! Coz-

WJ200UM-01-..

WS-..

K3

y x

This orientation not possible for WS-10-40/WS-10-80/WS-10-120

zy x

B

C

s

K1

C3

C1

G1

H

da

di

a

hh2

A1b

nh

n

nb

X Y

nh n nb T X Y ly lz

[mm4] [mm4]

15.5 5.2 9.5 M5 23 16 97,560 54,91015.5 5.2 9.5 M5 55 16 483,653 83,61327.6 10 15.4 M5 40 27.0 540,876 773,489

Part No. Weight H57) da di L a A1 b h h2 s K1 C1 C3 G1

±0.25 –0.1 max.

[kg/m]

1.3 39 ±0.02 10 6 4,000 38.2 16.5 40 26.5 30 60 M6 29 16 302 39 ±0.02 10 6 4,000 72.2 16.5 74 26.5 30 94 M6 29 16 47

4.2 65 ±0.02 16 6 4,000 62 25 58 49 52 100 M8 36 18 50

WSX-10-40

Length

Order key

Type


WJ200UM(T)-... WJ200UME-... WJUM-..-ES-FG WJRM-... WW-... WWE-... Hybrid carriage

Rai

l len

gth

[mm

]

Hig

h pr

ofile

rail

Pro

file

rail

Sha

fts-

Ø

Rai

l wid

th [m

m]


WK-10-40-15-01-1500-HKA C5=20

WW-10-40-10WW-10-40-15WW-10-40-20WW-10-80-10WW-10-80-15WW-10-80-20WW-10-120-10WW-10-120-15WW-10-120-20WW-16-60-10WW-16-60-15WW-16-60-20WW-20-80-15WW-20-80-20WW-20-80-25WW-25-120-15WW-25-120-20WW-25-120-25

808 8093D-CAD files, prices and delivery time www.igus.eu/drylinW

drylin® W | Profile guides | Product rangedrylin® W profile guides

Lifetime calculation, configuration and more www.igus.eu/drylinW

drylin® W | Profile guides | Ordering options

Part No. Weight A C A2 C2 K2 H257) Stat. load capacity Width Length ±0.25 Coy Coz Mox Moy Moz

[kg] [N] [N] [Nm] [Nm] [Nm]

0.29 73 100 60 87 M6 24 4,800 2,400 96 170 1700.34 73 150 60 137 M6 24 4,800 2,400 96 290 2900.40 73 200 60 187 M6 24 4,800 2,400 96 410 4100.34 107 100 94 87 M6 24 4,800 2,400 178 170 1700.42 107 150 94 137 M6 24 4,800 2,400 178 290 2900.50 107 200 94 187 M6 24 4,800 2,400 178 410 4100.41 153 100 140 87 M6 24 4,800 2,400 288 170 1700.54 153 150 140 137 M6 24 4,800 2,400 288 290 2900.66 153 200 140 187 M6 24 4,800 2,400 288 410 4100.71 104 100 86 82 M8 35 8,400 4,200 240 270 2700.84 104 150 86 132 M8 35 8,400 4,200 240 480 4800.97 104 200 86 182 M8 35 8,400 4,200 240 690 6901.20 134 150 116 132 M8 44 12,800 6,400 525 670 6701.30 134 200 116 182 M8 44 12,800 6,400 525 990 9901.50 134 250 116 232 M8 44 12,800 6,400 525 1,250 1,2502.54 195 150 173 128 M10 55 19,200 9,600 1,250 880 8802.80 195 200 173 178 M10 55 19,200 9,600 1,250 1,360 1,3603.07 195 250 173 228 M10 55 19,200 9,600 1,250 1,840 1,840


H2

WJ200UM-01-...

WS-...

WW-K2

A2 A

C2C

Assembled guide carriage, round

In the following sizes, also available with adjustable clearance: 10, 16 and 20; order example: WWE-10-40-15

zy x


WS-... WS-...-ES-FG WSX-...



Order key complete system:

Order example:WK-10-40-15-01-1500: fully assembled linear guide system comprising a rail (WS-10-40) with a length of 1,500 mm and a width of 40 mm plus a guide carriage (WW-10-40-15) with a length of 150 mm and a width of 73 mm.

Valid for guide carriages:Standard, symmetrical hole pattern: C5=C6; in the case of C5≠C6, please order with a drawing.Optional: rails without bores available (suffix "NO BORES").

Rail options Leave blank: Standard rail with

attachment holes C5= … mm: Only with a non-symmetrical hole

patternCarriage options Blank: Standard -HKA: Carriage with assembled manual

clamp (available installation sizes/lengths Page 968)

Model WK: Complete system with rails and

carriage WS: Individual rail W(...)UM: Individual housing bearing WW: Complete carriage

Com

plet

e sy

stem

Sha

ft d

iam

eter

Rai

l wid

th

Leng

th o

f car

riage

Num

ber o

f com

plet

e ca

rria

ges

Rai

l len

gth

[mm

]

Car

riage

opt

ions

Rai

l opt

ions


WSQ-06-30-CAM-500 WSQ-06-30WS-10-40-CAM-500 WS-10-40WS-10-40-CAM-1000 WS-10-40WS-10-80-CAM-500 WS-10-80

± 1 ± 1 [kg/m]

WSQ-06-30-SL-1000WSQ-06-30-SL-1500WS-10-40-SL-1000WS-10-40-SL-1500WS-10-80-SL-1000WS-10-80-SL-1500WS-16-60-SL-1000WS-16-60-SL-1500WS-20-80-SL-1000WS-20-80-SL-1500

WW-06-30-06-SLWW-06-30-08-SLWW-06-30-10-SLWW-10-40-10-SL64) 65)

WW-10-40-15-SL64) 65)

WW-10-40-20-SL64) 65)

WW-10-80-10-SL64) 65)

WW-10-80-15-SL64) 65)

WW-10-80-20-SL64) 65)

WW-16-60-10-SL65)

WW-16-60-15-SL64) 65)

WW-16-60-20-SL64) 65)

WW-20-80-15-SL64) 65)

WW-20-80-20-SL64) 65)

WW-20-80-25-SL64) 65)

810 811




Double rail, weight-reduced, hard-anodised aluminium Double rail/carriage for camera slider

C6C40.5 x L

L

S

WS-10-40-CAM-500

WS-10-40-CAM-1000

K1 (4x)

C5

K4

K1 (8x)K4

WSQ-06-30-CAM-500

K4K1 (8x)

K1 (10x)K4

WS-10-80-CAM-500

20

Application example: Camera slider with standard rail and carriage

www.igus.eu/camera

Part No. Identical profile

L C4 C5 C6 S K1 for screw

K4 Weight

DIN 192 [g]

500 60 10 10 12 M5 3/8" 16-UNC63) 159500 120 10 10 20 M6 3/8" 16-UNC63) 353

1,000 120 20 20 20 M6 3/8" 16-UNC63) 706500 120 10 10 20 M6 3/8" 16-UNC63) 482

Part No. Size L C5 C6 Weight± 1 ± 1 [kg/m]

06 1,000 100 100 0.4506 1,500 100 100 0.4510 1,000 100 100 1.0010 1,500 100 100 1.0010 1,000 100 100 1.5010 1,500 100 100 1.5016 1,000 100 100 1.9616 1,500 100 100 1.9620 1,000 100 100 3.3020 1,500 100 100 3.30

drylin® W guide rail – Dimensions [mm]

30 % weight reduction through machined recesses

Installation sizes: 0630, 1040 and 1080 Lubrication free, quiet and lightweight Standard lengths from stock Matching housing bearing and carriage made from plastic, aluminium, die-cast zinc or stainless steel

63) * UNC = Unified National Coarse, Anglo-American. Screw thread standard

Wear resistant, smooth and quiet motion Adjustable brake level due to the turn-to-fit function Lubrication free Easy and fast assembly Further dimensions such as standard rails WSQ

Page 802 and WS Page 806

Technical options: Adjustable bearing housing Manual clamp (WW...-HKA Page 812)

drylin® W special rails with 3 holes, 3/8" thread

Part No. Size C A06 60 5406 80 5406 100 5410 100 7310 150 7310 200 7310 100 10710 150 10710 200 107

drylin® W complete carriage with ø10 mm through hole for 3/8" thread

Part No. Size C A16 100 10416 150 10416 200 10420 150 13420 200 13420 250 134

64) Optional with integrated manual clamp (add suffix "-HKA")65) Optional with adjustable "Turn-To-Fit" bearing (Order example: WWE-…)

L

C5 C6

L/2 ± 1

K1

C

C2

A2 A

K2

H

C/2

b

K3

Dimensions [mm]

Dimensions [mm]

WHKA-0666)

WHKA-1066)

WHKA-1666)

WHKA-2066)

WHKA-2566)

WHKA-06-AL 68)

WHKA-10-AL 68)

WHKA-16-AL 68)

WHKA-20-AL 68)

WHKA-25-AL 68)

WHKD-1010 69)

WHKD-101569)

WHKD-161569)

WHKD-162069)

WHKD-201569)

WHKD-202069)

812 813






Mk

Dk

Vx

K x

Vz

K z

66) The manual clamp is also available assembled as a complete carriage (suffix "-HKA", order example WW-10-40-10-HKA) Complete carriage WW, Page 808

67) Condition: dry rail surface

68) The manual clamp is also available assembled as a complete carriage (suffice "-AL-HKA", order example: WW-10-40-10-HKA) Complete carriage WW, Page 808


Part No. Mk Vx Kx Vz Kz Dk Min. holding strength67) Min. tightening torqueM6 34.5 21.5 8 28 20 30 N 0.8 NmM6 50 33 8 28 20 30 N 0.8 NmM8 72 41 10 31 28 60 N 1.5 NmM8 90 62 10 31 28 70 N 1.5 NmM8 96 65 12 31 28 70 N 1.5 Nm

Part No. Mk Vx Kx Vz Kz Dk Min. holding strength67) Min. tightening torqueM6 34.5 21.5 8 28 20 30 N 0.8 NmM6 50 33 8 28 20 30 N 0.8 NmM8 72 41 10 31 28 60 N 1.5 NmM8 90 62 10 31 28 70 N 1.5 NmM8 96 65 12 31 28 70 N 1.5 Nm


Mk

Dk

Vx

Kx

Kz

Vz

69) The hand clamp WHKD is available assembled in the following complete carriages: WW-10-40-10-HKD, WW-20-80-15-HKD. Dimensions Complete carriage WW, Page 808


Part No. Mk Vx Kx Vz Kz Dk Min. holding strength67) Min. tightening torqueM6 100 45 40 10 40 70 N 2.5 NmM6 150 95 40 10 40 70 N 2.5 NmM8 150 81 40 12 40 90 N 3.5 NmM8 200 131 10 12 40 90 N 3.5 NmM8 150 63 40 12 40 90 N 3.5 NmM8 200 113 40 12 40 90 N 3.5 Nm

Manual clamp for simple positioning

Aluminium manual clamp

Manual clamp for higher retention forces

815814

drylin® W | Accessories | Product range

Lifetime calculation, configuration and more www.igus.eu/drylinW

drylin® W | Profile guides | Installation instructions

Tightening torque for drylin® connections between metal parts Page 778

Size Material Housing bearing Tooth profile Bearing Part No.10/16/20/25 iglidur® J200 WJ200UM-01-ø round J200UMO-01-ø10/16/20/25 (floating bearing) iglidur® J200 WJ200UM-01-ø LL round J200UMO-01-ø LL10/16/20 iglidur® X WXUM-01-ø round XUMO-01-ø10 (adjustable) iglidur® J WJUME-01-10 round JUME-01-1016/20 (adjustable) iglidur® J200 WJ200UME-01-ø round J200UME-01-ø6/10/16/20 iglidur® J200 WJ200QM-01-ø square J200QM-01-ø6/10/16/20 (floating bearing) iglidur® J200 WJ200QM-01-ø LLY/LLZ square J200QM-01-LL70)

drylin® W spare polymer plain bearings

End caps

70) Depending on assembly direction, can be used as a y or z floating bearing

1

2

1

2

F = 50 N

F = 50 N

drylin® W rail with housing bearingsDuring the installation process, a compressive force of minimum 50 N is recommended on the centre of the mounting surface. Alternatively, a plastic hammer/soft face hammer can be used during and after the mounting to align the bearing.

drylin® W rail with complete slide systemDuring the installation process, a compressive force of minimum 50 N is recommended on the centre of the mounting surface. Alternatively, a plastic hammer/soft face hammer can be used during and after the mounting to align the bearing.

Installation size Max. tightening torque [Nm]

Thread

W-06 1.5 M4W-10 6.0 M6W-16 15.0 M8W-20 15.0 M8W-25 30.0 M10

Installation size Max. tightening torque [Nm]

Thread

W-06 1.5 M4W-10 6.0 M6W-16 15.0 M8W-20 15.0 M8W-25 30.0 M10

Please refer to the drawing for the correct screw assembly sequence.

End caps for drylin® high profile rails WSXSuitable for drylin® W high profile rails, the new end caps also offer, besides an elegant rail end, a practical protec-tion against the ingress of dust, dirt or chips. Available in 4 installation sizes.

For drylin® W high profile rails WSX 4 installation sizes Protection of the hollow chambers against the entry of foreign particle

Easy to fit End caps for cutting edges

Part No.WSX-0630-ECWSX-1040-ECWSX-1080-ECWSX-1660-EC

3D-CAD files, prices and delivery time www.igus.eu/drylinW



816

Documents

drylin W Proﬁle guides - igus · drylin® W Proﬁle guides Easy installation ... aluminium is used as rail material and provides ... Metal sheet cladding max. 200 ¡C