1. Company XYZ has a multi-location voice network. They have Session Manager at their main site and Avaya Communication Manager (CM) and Cisco Call Manager at their branch locations. Which type of messages does Session Manager send to the Avaya and Cisco PBX configured as SIP Entities to monitor their status? a.ENTITY b.LINK c.OPTIONS d.STATUS Answer :C

After a power failure or database crash, the Postgres database may become corrupted and the Postgres server may not restart. The recovery action is to clear the writer-Ahead Log (WAL) and optionally reset other control data, using which command? a.pg_resetxlog b.pg_clearwal c.pg_dump d.service postgresq1 restart e.service wall restart Answer :A

During a post-installation check of System Manager and Session Manager you discover that the Session lager replica node is stuck at "Synchronizing". You run the initTM command in Session Manager but the replication status does not change. Which step will be effective in resolving the problem? a.Reset the enrollment password. b.Run traceSM to monitor the synchronization events and restart the Security Module. c.Delete the Session Manager Replica node in System Manager, verify the enrollment password is valid In System Manager and run the initTM command again in Session Manager. d.Verify the enrollment password is valid in System Manager and run the initTM command again in Session Manager. Answer :D

Which three types of handles can be selected for a user when creating users in system manger? (Choose three.) a.SMTP b.H.323 c.IBM d.XMPP e.undefined Answer :A,C,D

A new Application Sequence has already been defined in the network. A technician has been asked to apply Application Sequence to all incoming calls for all employees in the Berlin office. Which sequence describes the steps that should be taken? a.Go to the User Management page and use the filter option to list only the users in the Berlin office-Select each user from the filtered list and edit each user s User Profile. Apply the new Application Sequence to the Terminating Application Sequence for each user. b.Navigate to the Communication Profile Editor and use the filter option to list only the users in the Berlin location. Select All. Select the new Application Sequence from the Terminating Application Sequence drop down box. c.Go to the list of Application Sequences and edit the new Application Sequence, adding the Berlin location to the list of associated locations. d.Edit the Berlin Location to include the new Application Sequence as its Terminating Application Sequence. Answer :B

Which statement is true with regard to SIP Monitoring being enabled on a SIP Entity? a.Session Manager will monitor the status of that SIP Entity by sending SIP OPTIONS requests. b.SIP Entity will monitor the status of Session Manager by sending SIP OPTIONS requests. c.Session Manager will monitor the status of that SIP Entity by sending SIP SUBSCRIBE requests. d.Session Manager will monitor the status of that SIP Entity by sending SIP NOTIFY requests. e.System Manager will monitor the status of that SIP Entity by sending SIP OPTIONS requests.

Answer :A

Digit Conversion in Adaptation can be specified to modify "origination" type headers. Which three are origination / source type URIs?(Choose three.) a.Request-URI b.P-Asserted-Identity c.Refer-To (in REFER messages) d.History-info (calling portion) e.Contact (in 3xx response) Answer :B,D,E

While reviewing the session Manager logs, you notice a log entry that describes that state of an entity “down”. Later, you check the logs and notice another log entry that reports the same entity is “partially up”. Which troubleshooting procedure will help you to isolate and identify the Entity problem? a.Run traceSM to capture SIP INVITE message from the entity to determine if there is a display in the network. b.Run SIPmonitoringdiagnostics along with ICMP ping to the Entity to verify its connectivity. c.Run traceSM100 to capture SIP MONITOR message from the entity to determine if there is a delay in the network. d.Run SIP Entity Performance on the Entity to determine id SIP OPTIONS messages are being blocked on the network. Answer :A

What are two reasons for creating a network location?(Choose two.) a.Locations are used to implement Call Admission Control. b.The location of a caller is used to determine which Session Manager will process the request. c.Locations are used to limit the number of users that may register to the session manager specific physical location.

d.Session Manager uses the termination location of a caller to determine which dial patterns to look at when routing the call. e.Session Manager uses the origination location of a caller to determine which dial patterns to look at when routing the call. Answer :A,E

What is the benefit of using the Communication Profile Editor to modify users? a.It allows an administrator to change some values of a User Profile for multiple SIP users at one time. b.It allows an administrator to change the values of the Session Manager Profile settings for only a single SIP System Manager user at one time. c.It allows an administrator to change some values of the Communication Profile settings for multiple SIP System Manager Users at one time. d.It allows an administrator to change all values of a User Profile for multiple users at one time. Answer :B

What is validated when the Transport Layer Security (TLS) handshake and mutual TLS authentication is performed between the SIP entity and Session Manager? a.entity link b.entity name c.domain d.certificate Answer :D

Which two statements describe how adaptations affect the routing of a request?(Choose two) a.Session Manager making the routing decisions after applying anyadministered incoming adaption b.Session Manager making the routing decisions after applying anyadministered outgoing adaption c.Session Manager making the routing decisions before applying anyadministered incoming adaption d.Session Manager making the routing decisions before applying anyadministered outgoing adaption Answer :A,D

Which parameter is required when installing the System Manager 6.1 (SMGR) template? a.SMGR IP address b.The IP of the remote server providing High Availability c.Subnet network mask d.Network Time Protocol (NTP) settings. e.Default Gateway IP Answer :A,C,D

What is the outcome of running SMnetsetup on a server that has an existing installation of session manager 601? a.The network and date/time is configured on the server. b.A System Manager System administrator login will be created. c.The same version of the Session Manager software currently Installed is re-installed? d.The current version of the Session Manager software is upgraded. Answer :A

From where can a System Manager (SMGR) export of user data be performed? a.from an SSH session with the System Platform Dom-0 b.from an SSH session with the System Manager virtual machine c.from an SSH session with the System Platform C-Dom (utilities domain) d.from a web client access System Manager web interface User Management Answer :D

A technician in is tasked with moving a user from one redundant Session Manager pair to another Which sequence describes the steps that should be taken? a.Go to the User s User Profile. Select different Session Manager instance from the Primary Session Manager and Secondary Session Manager lists.

b.Go to the user s User Profile. De-select the current community. Select the new community. c.Navigate to the Communities page. Select the Community into which the user will be moved. Select the user from a drop down list to add the user to the community. d.Go to the Locations page. Select a location, define it as a Primary community and add the user. Select another location, define it as a Secondary community and add the user. Answer :A

A technician wants to schedule a bulk operation to take place at a convenient time in the future What are two methods for scheduling bulk operations?(Choose two.) a.# Sh exportUpmUsers.sh -u admin -p adminl23 -t 2013:05:01:12:00:00 b.# sh exportUpmUsers.sh -u admin -p adminl23 -d 2013:05:01:12:00:00 c.Navigate to Users > User Management, click More Options and select Import Users . Choose schedule in the options. d.Navigate to Users > User Management, click More Options and select Export Users . Choose schedule in the options. Answer :C,D

Which statement describes the relationship between System Manager and System Platform? a.System Platform hosts System Manager. b.System Platform provides access to System Manager s data repositories. c.System Manager is the User Interface through which System Platform is administered. d.System Manager and System Platform are peer applications, both installed on Avaya S8800 servers. Answer :A

Which two statements describe the purpose of a System Manager (SMGR) role?(Choose two.) a.It provides access to any number of resources managed by SMGR. b.It impacts the originating and terminating applications that can be sequenced for a user. c.It is automatically held by users that have been added to any group containing that role.

d.It can be held by multiple administrators at the same time and a single administrator can have multiple roles enabling tight control of access. Answer :A,D

How is request routed to a "Named" Application? a.Session Manager uses the phase tag of a route header of the incoming request and matches it to a dial pattern then uses the associated Routing Policy. b.Session Manager uses the route header of the incoming request and matches it to a dial pattern then uses the associated Routing Policy. c.Session Manager uses the Request URI of the incoming request and matches it to a dial pattern then uses the associated Routing Policy. d.Session Manager uses the termination application sequence associated to the Communication Profile of the user to route the request. Answer :C

Which two statements about backing up System Manager (SMGR) product and user profile data are true?(Choose two) a.It is used when moving user details from one SMGR to another SMGR in the Avaya Aura ecosystem. b.It is made to a file location, either on or off the SMGR server. c.It is made to preserve user and other configuration data during a SMGR upgrade. d.It is used later when attempting to restore role definitions that may have become corrupted without affecting other configuration changes made after the backup was taken. Answer :B,C

Which two functionalities does the SIP firewall provide to protect Session Manager from SIP flood attack?(Choose two.) a.Removing the suspected source b.Rate Limiting

c.Blocking the Entity Link d.Rate Blocking Answer :B,D

Application definitions allow system administrators to define and mange individual applications each with their own attributes. The definitions allow administrators to add one or more such applications to which of the following? a.application programs b.application data sets c.application sequences d.application lists Answer :C

Why is FQDN resolution important between Session Manager and System Manager when the FODN is unresolvable to either the Session Manager or System Manager? a.Session Manager node registration will fail during installation and data will not be replicated from System Manager to Session Manager. b.System Manager node registration will fail during installation and data will not be replicated from System Manager to Session Manager. c.Session Manager node registration will fail during installation and data will not be replicated from Session Manager to System Manager. d.Trust management will fail during installation and data will not be replicated from Session Manager to System Manager. Answer :A

Application definition allows system administrators to define and manage individual applications, each with their own attributes? The definitions allow administrators to add one or such applications to which of the following?

a.application programs b.application data sets c.application sequences d.application lists Answer :C

Which statement expresses the relationship between users, roles, and groups? a.Roles grant permissions. Users are not directly assigned roles but inherit them through belonging to groups. b.A group is a name for a collection of roles and each role is assigned its own administrator user. c.Users can belong to groups for easy management and can be assigned roles which grant them access rights. d.Groups and roles directly correspond to sections of the SMGR Web Console navigation pane and, unless a user belongs to a specific role group, they cannot access the corresponding management screens. Answer :C

A known and trusted SIP Entity is anticipated to deliver a higher than normal number of SIP messages to session Manager. Two techniques can be applied to prevent the SIP Firewall dropping or blocking from this trusted SIP Entity. Which techniques will prevent the SIP Firewall dropping or blocking packets from this trusted SIP Entity?(Choose two.) a.Configure the SIP Entity to point to Session Manager s Eth3 NIC. b.Configure the SIP Firewall Fast Track group to include the SIP Entity. c.Add details of the SIP Entity to the White List. d.Increase the Threshold packet count for the SIP Entity. Answer :C,D

If two standalone session Managers and one standalone System Manager are going to be installed, how many IP Addresses will you need? a.3

b.5 c.6 d.7 e.9 Answer :D

While performing routine maintenance a technician has had to re-install System Platform. Which statement describes what must be done next? a.The SMGR Template must be installed. b.The SMGR Template must be installed, followed by the utilities domain (in that order), c.The utilities domain must be installed, followed by the SMGR Template (In that order), d.The Dom-0 must be installed, followed that order) by the utilities domain and then the SMGR Template (in that order). Answer :A

An originating Application Sequence has been configured to route calls from a given user to a feature server. It appears however, that the feature is not being applied when a call is made. What would be the best course of action an administrator should take to identify the issue? a.Run traceSM and make the call. Check the SIP INVITE is routed to the feature server. Check the content of the Route header. b.Make a test call. Open Session Manager calltrace.log. Look for error messages that identify routing issues. c.Run the Call Routing Test utility from within System Manager. Filter on caller address and route header. d.Run a network packet capture tool, filtering for SIP messages. Make the call and check that the anticipated SIP messages are exchanged between SIP telephones. Answer :A

Which two wildcard characters does Session Manager allow to specify a location pattern? (Choose two). a.“%” (percentage) b.“$” (dollar) c.“*” (star/asterisk)

d.“#” (pound/hex) e.“X”

Answer :C,E

Avaya products ensure that authentication credentials and file transfers are protected when sent across the network by using which three methods?(Choose three) a.Telnet b.HTTPS c.Secure Shell (SSH) d.Secure Copy (SCP) e.HTTP Answer :B,C,D

A new feature server has been deployed in the network. The feature server must be applied to all calls made and received by the user. A technician has been asked to make the necessary arrangements. After adding a SIP Entity and Entity Link, which sequence describes the next steps that should be taken? a.Navigate to the user s User Profile and open the Session Manager Profile. From the Originating Application Sequence drop down list, select the new Application Sequence. Repeat for the Terminating Application Sequence drop down list. Mark them both as being Mandatory. b.Define the new feature as an Application. Add the Application to an Application Sequence. Mark the Application Sequence as Mandatory. Add the Application Sequence to user s User Profile. c.Create a new Application Sequence or edit one that already exists. Add details of the new feature to the Application Sequence. Mark the new feature as being mandatory. Apply the Application Sequence to user s Originating and Terminating Application Sequences In their Session Manager Profile. d.Define a new Application that details the new feature. Add the new Application to an Application Sequence. Mark the new feature as being mandatory. Apply the Application Sequence to both Originating and Terminating Application Sequences in the user s Session Manager Profile. Answer :C

An IMS type feature server has been installed by another administrator team. They have also configured session manager to route all incoming calls for a user to be routed to the new feature server. It appears from running traces and capturing network traffic that Session does indeed route the User s incoming calls to the feature server, but that the feature server does not appear to take any action besides

returning the request back to Session Manager. Which field may be incorrectly configured? a.Application Handle b.Entity Link port c.Originating Application Sequence d.Terminating Application Sequence Answer :A

Which header in the request is considered by Session Manager when it is trying to match a dialed number? a.Session Manager attempts to match the FROM header of a request to a defined dial pattern. b.Session Manager attempts to matchtothe header of a request to a defined dial pattern. c.Session Manager attempts to match the request-URI header of a request to a defined dial. d.Session Manager attempts to match the ROUTE header of a request to a defined dial pattern. Answer :C

In which configuration do multiple Session Manager Instances run for optimal redundant a.Active-Standby b.Supervisor Redundant c.Hot Standby d.Active-Active Answer :D

A routing policy administrator needs to create a policy that enables Session Manager to route to different destination based on different conditions. Time of day is one such condition. Which two Parameters may also be used by Session Manager when selecting the applicable routing policy?(Choose two.) a.the location of the calling party b.the registration state of the destination c.the SIP domain of the called party d.the origination or termination application sequences that will be applied to call, ignoring what the applications themselves may do

Answer :A,C

Users between four customer sites are reporting frequent problems placing and receiving calls. In trying to identify the issue, you check the Bandwidth Usage between Session Manager Locations and get an error message, “Unable to access status information for SM1 – cannot connect to server, internal error”. Which item is most likely the cause of this error? a.There is limited bandwidth between the locations. b.The Session Manager Service State was set to deny new service. c.The System Manager cannot communicate with the Session Manager because of a network issue. d.The Session Manager is processing high volume of calls and is causing inter-SM server connectivity problems. Answer :D

R has started importing a file containing many user records. What will SMGR do if it encounters a record it cannot import? a.It will abort the operation and roll back any successfully imported records from the import file. b.Whether SMGR will abort and rollback the operation or continue processing records is entirely configurable. c.Whether SMGR will abort or continue processing records is entirely configurable; but you cannot rollback successfully imported users. d.It will continue processing the rest of the import file and collate the failures into a single XML document that can be retrieved following the import. Answer :B

All administrator is instructed to add a Regular Expression to Routing Policy that matches all dialed numbers being with a 14 and 15 (for example 14000 and 15999, but not 24000). Which two regular expression patterns will match against such numbers?(Choose Two) a.sip: [1]{1}4*5*[0-9]{3} b.sip: [1]{1}[4-5]{1}[0-9][3] c.sip: 1[4-5][0-9][0-9] d.sip: 1(4/5){1}[0-9]*

Answer :B,C

How is call Admission Control enabled for Session Manager Release 6.1? a.Call Admission Control is enabled in the SIP Entity by specifying a value for Managed Bandwidth. b.Call Admission Control is enabled on the Session Manager instance by specifying a value for Managed Bandwidth. c.Call Admission Control is enabled on a Location by specifying a value for Managed Bandwidth. d.Call Admission Control is enabled on an Entity Link specifying a value for Managed Bandwidth on the Locations screen in Session Manager. Answer :D

An organization is adding four Session Managers installed to its network. The installation scripts for all four session Manager Instances have completed and all services have been started but none have yet been configured with Session Manager. The technician s task is to use System Manager to set up the four Session Managers in an in (n- 1)/n redundant arrangement ready for adding users to redundant Session Manager Pairs. Which sequence best describes the tasks that are to be performed? a.Ensure that a Location and SIP Domain suitable for each Session Manager is defined. Add each Session Manager as a SIP Entity. Associate each Session Manager SIP Entity with a Session Manager instance. Set up Entity Links between each Session Manager. b.Define each Session Manager as a SIP Entity. Establish relationships between them by defining Routing Policies based on their respective locations. Add appropriate Adaptations to each Session Manager. c.Define each Session Manager as a SIP Entity by creating Entity Links. Create Communication Profiles for each Session Manager. d.Add each Session Manager as Routing Agents. Establish links between them by adding Locations. Mark each Session Manager as being active or standby . Answer :A

Shortly after an installation, SIP users in abc.com domain are registered but not able to call H.323 users in training.com domain. When you run traceSM you see a “403 Forbidden” error when users try to call each other. What is the issue and which troubleshooting procedure will help you to identify and isolate the problem? a.Replication Failure: run initDRS to reinitialize the synchronization between system and session

manager. b.Network Issue: status the Bandwidth usage to each location and make sure Call Admission Control is activated. c.Misconfigured Communication profile: Sip Users have not been associated to the CM endpoint. d.Incorrect Routing: verify domains were properly configured in System Manager, verify an adaption to modify the secure/destination domain was created and applied to the appropriate sip entity. Answer :C

A System Manager (SMGR) product administrator needs to perform some routine maintenance on an Avaya product in their network. Although they can successfully log in to SMGR, they do not have access to the menu they require in the navigation panel. Which action must be taken? a.Make sure that the administrator has been assigned to a suitable group. b.Make sure that the administrator is not logged in at a different browser. c.Ensure that the administrator s authentication type is set to enterprise so that SMGR can retrieve permissions from the active directory server. d.Check that the administrator has been assigned an appropriate role. Answer :D

The System Manager administrator must consider the implications of restoring System Manager Data. Which two restore-from-backup statements are true?(Choose two.) a.The restore operation will terminate all SIP sessions, and no SIP services will be available until the operation completes. b.The restore operation will take a varying amount of time depending on the amount of data. c.The restore operation will be scheduled for a time when the network is not busy. d.The restore operation will over-write all System Manager data held in the repository. Answer :B,C

A Configuration Manager instance has been set up by an inexperienced administrator. A SIP entity in the network is failing on a regular basis and Session Manager sometimes does not detect the failure for up to 30minutes. Which two Session Manager Configuration fields could have been set incorrectly?(Choose two) a.Proactive cycle time.

b.Reactive cycle time. c.Timer period d.Override port and transport with DNS SRV Answer :A,D

While reviewing the Event Logs on the Session Manager, you notice an ALERT message: (OP_AFW17504) “SIP firewall white list configuration failed, retaining existing configuration.” Which action should you perform when you see this alert? a.Access the SIP firewall white list configuration and verify that the configuration is correct. b.Access the SIP firewall configuration and change the RULE log type to none to not have these ALERTS appear in the EVENT logs. c.Access the SIP firewall configuration and Load the ASM Default Configuration. d.Disregard these messages as they are sent to the Event Logs and do not generate alarms. Answer :A

A technician has been asked to apply an Application Sequence to call made from / to a non-SIP user who does not have Session Manager Profile. Which sequence describes the steps that should be taken? a.Add an Avaya-SIP Communication Address to the user s User Profile. Add a Session Manager Profile to the user s User Profile. Select appropriate Originating and Terminating Sequences for the user from the options in the new Session Manager Profile. b.Create a new Implicit User rule. Define a number pattern that can be compared with dialed numbers. Select appropriate Originating and Terminating Sequences to be applied when a match occurs. c.Navigate to the list of Application Sequences and select the sequence to apply to the non-SIP user. Add the user s extension number to the list of associated users. Select appropriate check box options to determine if the sequence should be applied In originating mode, terminating mode or both. d.Create a new Non-SIP User Application Sequence Policy. Define the address and location of the non-SIP user. Select appropriate Originating and Terminating Sequences for the non-sip user from the given options. Answer :B

When you upgrade Session Manager you had been using the hardware SM-100, the network connection of the SM-100 must be moved to which port on the Session Manager server?

a.eth2 port, labeled “2” b.eth2 port, labeled “3” c.eth0 port, labeled “1” d.eth0 port, labeled “0” Answer :B

Review the error message in the installation log shown in the exhibit. What is the probable cause for initDRs to fail and how can it be fixed? a.There is a non-bidirectional FQDN resolution between Session Manager and System Manager. Verify the enrollment password used to initialize trust management has not expired b.There is a JMX connection error. Verify the enrollment password used to initialize trust management has not expired. c.There is a non-bidirectional FQDN resolution between Session Manager and System Manager. Verify that either the System Manager or the Session Manager has updated DNS records or the hostnames have been added to the /etc/hosts file on the Session Manager and the System Manager. d.There is a JMX connection error. Verify that either the System Manager or the Session Manager has updated DNS records, or the hostnames have been added to the /etc/hosts file on the Session Manager and the System Manager. Answer :C

What three pieces of information are required to be entered for the Session Manager to be installed and synchronized with System Manager?(Choose three.) a.System Manager IP Address b.Session Manager Security Module Address c.System Manager FQDN d.DNS Server Address e.Enrollment Password Answer :A,C,E

Which three statements about a user s profile are correct?(Choose three.) a.Branch Session Manager (BSM) association is set in the Session Manager Profile under the user s Communication Profile. If a primary Session Manager has been selected then assigning a BSM mandatory. b.Using the Endpoint Profile a user can be assigned a station on a Communication Manager that SMGR knows about. c.The difference between the SMGR Login Password and the Shared Communication Profile Password is that one allows the user to login to the SMGR web interface and the other allows them to authenticate at a device. d.A user may be assigned exactly one role. That single role can allow access to multiple resource types. e.User identity authentication (password checking) can be achieved by first configuring SMGR to communicate with an LDAP server and then choosing the profile Authentication Type as Enterprise . Answer :B,C,E

On a SIP Entity that is defined as type session Manager, what should be defined? a.an adaptation b.listening ports c.an outbound proxy d.a credential name Answer :B

Session Manager has a routing policy that routes calls made to any number beginning with 100 to SIP Entity X. However, sip.-1001avaya.com is the SIP communication profile address of user Y. User Y is not currently registered (signed in) with Session Manager. What will happen if Session Manager receives a call addressed to sip.-1001avaya.com and why? a.It depends on the time ranges of the policy. If the call is placed inside a defined time range for the policy, the call will be routed to destination X. If not, then Session Manager will attempt to route the call to user Y. Since Y is not registered, the call will timeout, and the call will fail. b.Since user Y is not currently registered, the call will be handled by the routing policy. If the call is placed during a time range specified by the policy, then the call will be routed to destination X. If not, then the call will fail. c.Since the destination URI matches a communication profile SIP handle, Session Manager will not use

the routing policy in handling the call. The call will fail since user Y is not currently registered. d.Since the destination URI matches a routing policy dial pattern, Session Manager will give no consideration to the user Y registration status. If the call is made during a time range for the policy, the policy will be applied and the can will be routed to destination X. If not, then the original URI of sip.-1001avaya.com will be used as the destination to which Session Manager will route the call. Answer :C

A technician is tasked with creating a set of Routing Policies for the organization. Which statement describes the steps that must be taken prior to defining a new Routing Policy? a.A SIP entity must be specified as both a destination and as an origination point. You must provide the times of day that the policy applies, and a dial pattern or regular expression that the call URI must match. b.The destination SIP entity can either be chosen specifically, or it may be selected implicitly using a matching expression. Multiple times of day the policy is active can be chosen. The policy must have either a dial pattern or regular expression. c.A dial pattern must be specified which the called party in the SIP message is matched against. Inclusion of a time range, or regular expression, is optional but recommended since it makes the policy more specific. d.A SIP Entity must be specified as a destination. Answer :C

A company has multi-location voice network. They are introducing Session Manager to make their routing centralized. They have Avaya Communication Manager at their main location. For the SIP telephone on Session Manager to call the H.323 telephones on communication Manager, which adaption module may be used in their configuration? a.ChangeDomain b.DigitConversionAdapter c.NumberAdaptation d.DomainChangeAdapter e.DefaultAdapter Answer :B

System Manager provides a Dashboard summary for monitoring and validating the health of each Session Manager instance. What information is not available from the Session Manager Dashboard? a.Service State b.Security Module status c.Entity Monitoring d.Managed Bandwidth status Answer :D

Which two statements about Managed Bandwidth are true?(Choose two.) a.If the Managed Bandwidth field is blank for a location no Call Admission Control is done for that location. b.If the Managed Bandwidth field has a value. Session Manager keeps track of the bandwidth in use based on the calls coming out of and going to that specific location and denies new calls when the bandwidth in use reaches the limit. c.If the Managed Bandwidth field is blank for a location, the default Call Admission Control is done for that location. Session Manager keeps track of the bandwidth in use based on the calls coming out of and going to that specific location and denies new calls when the bandwidth in use reaches the limit. d.If the Managed Bandwidth field has a value. Session Manager keeps track of the bandwidth in use based on the calls coming out of and going to that specific location and drops old calls when the bandwidth in use reaches the limit. e.If the Managed Bandwidth field has a value, Session Manager keeps track of the bandwidth in use based on the calls coming out of and going to that specific location and sends an alarm to an administrator when new calls reach the bandwidth the limit. Answer :A,B

Which component of the Communication Profile can be changed by modifying a user via Communication profile editor? a.Communication Address b.Session Manager Profile c.Endpoint Profile d.Messaging Profile Answer :B

Which statement describes the purpose of Timer B? a.Timer B determines the maximum allowable call duration. b.Timer B determines the length of time Session Manager allows a telephone to ring before canceling the call and routing it elsewhere. c.Timer B determines the maximum time period between a dispatched request and the anticipated "200 OK". d.Timer B determines the period of time a Session Manager waits for a response before canceling the request and perhaps routes it elsewhere. Answer :D

The Data Replication Service replicates data from the master database to local copies of the database on each Session Manager instance. It is important that the master and local database are synchronized. How would an administrator check that the databases are synchronized? a.Run initDRS b.View the Session Manager Security Module status. c.Execute the Test Postgres database sanity maintenance test d.Check the status of the Replica Group Answer :C