P/N 01.BSM.16.2000030 V1.0Product Made in China under ISO9001 & ISO1400 standards
Manual Printed in China v1.0
900tvl
CMOS Technology High Resolution Sensor
AN2 Series
eLineTechnology.com
CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIEDSERVICE PERSONNEL.
CAUTIONRISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning with an arrowhead symbol, within an equilateral triangle is intended to alert the users to the presence of un-insulated “dangerous voltage” within the product’s enclosure that may be sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point with an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
To prevent electric shock and risk of fire hazards:
• Do NOT use power sources other than that specified.
• Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person and should conform to all local codes.
1 2
Guide
Solution General Specifications
General
Power source Regulated 12VDC
Power Consumption 100mA IR LED
IR LED On Power 10pcs Max 275mA 15pcs Max 320mA
Scanning system Progressive Scan Sensor
Scanning frequency NTSC 15.734KHz( H), 59.95Hz (V) / PAL 15.625KHz (H), 50Hz (V)
Effective Pixels 1305(h) x 1049(V)
Resolution 900TVL
OSD Control Optional Control via cable (see OSD Menu Page 7-8)
ACG / BLC On
Noise Reduction 2d/ 3d Enabled
Sync System Internal
Min. Illumination 0.01 Lux (AGC On, IE Off) / 0 Lux with IR LED On
Video output 1.0 Vp-p (75Ω , composite)
S/N Ratio More than 52dB (AGC OFF)
Video output BNC Connector 1.0Vp-p PAL / NTSC
Lens mount Fixed mount
Lens Matching for each model.
Operating temperature -10°C ~ +50°C / -40°F ~ 122°F
Operating humidity 0-90% (non-condensing)
Model Features:• 1/3” CMOS Sensor
• 900TVL Sensor imaging
• Day/Night / ICR
• Programming via OSD
• BNC Video Output
• Standard 12VDC Operation lower power
• Super flux IR LED for night vision
• 3D Noise reduction
*Specifications subjected to change without prior notice.
3 4
NOTE: Make sure you don’t have any missing parts before you make the installation. Incorrect installation could void the warranty if instructions are not followed correctly.Please call technical for assistance if you are unsure about any procedures.
IdentificationMechanical Drawing
InstallationInstallation information (General overview)
4
1 Remove visor from camera to aid simpler installation. (Optional requirement)2 Use drill template (D) as to guide to drill and attach camera to surface as required. Holes on bracket are 120 degree apart, so three holes are required.3 With camera attached you can now connect power, check device working.4 Using the (C) L-Hex tool you position left-right up/down and lock into place. The rear position rotation allows turning of angle turn anti-clockwise to loosen.5 Adjust zoom & focus using small flat blade. (Vari-focal model only)6 Replace the sun visor if removed from step 1. Check IR LEDs are working by covering the photocell of camera, the IR LEDs will give a faint red glow. (Don’t look at IR LEDs for long periods of time, as you could damage your eyes)
Accessories
(C) L-Hex tool54x18mm (D ) Drill template
(B) Fitting ScrewsPA4 x 24mm 3pcs
(A) Wall PlugsS7 x 26mm 3pcs
1
43
2
5 6
194 mm7 5/8 in
62 m
m2
3/8
in
226 mm8 7/8 in
77 m
m3
in
Locking Screw
Rotation lock
5 6
NOTE: Make sure you don’t have any missing parts before you make the installation. Incorrect installation could void the warranty if instructions are not followed correctly.Please call technical for assistance if you are unsure about any procedures.
IdentificationMechanical Drawing
InstallationInstallation information (General overview)
6
Accessories
Vari-Focal Lens Model
118 mm4 5/8 in
99 m
m3
7/8
in
1/2”
152 mm6 in
117.
5 m
m4
5/8
in
(C) L-Hex tool58x20mm (D ) Drill template
(B) Fitting ScrewsPA4 x 24mm 3pcs
(A) Wall PlugsS7 x 26mm 3pcs
1 Use supplied template to drill holes for (A) plugs.
2 Remove locking cover using supplied (C) L-key. Optional requirement
3 Attach base part to surface with (B) screws. Use conduit if required.
4 Re-attach Cover and position camera then lock cover screws with L-Key.
5 Adjust the zoom & focus using flat blade tool. (Vari-Focal models only)
6 Connect power, feeding through conduit may require this stage to be completed before adjustment is made. Check IR LEDs are working by covering the photocell of camera, the IR LEDs will give a faint red glow. (Don’t look at IR LEDs for long periods of time, as you could damage your eyes)
1
43
2
5 6
7 8
CAMERA ADJUSTMENT (option) CAMERA ADJUSTMENT (option)
MAINMENUIMAGE • 3D-NR • ON • OFF • AE MODE • CENTER • CENTER WEIGHT • BACK LIGHT • FRONT LIGHT • WB • AWB-TEMPORAL • AWB-AI • AWB-SZ • AWB-GW • AWB-CCT • AWB-PEO • IMAGE ENHANCE • SHARPNESS • DETAIL • EDGE • CONTRAST • AUTO • MANUAL • SATURATION • AUTO • MANUAL 0-15 • MIRROR • FLIP • BRIGHTNESS • ZOOM INDAY&NIGHT • AUTO • EXT • BLACK&WHITE • COLOR ZONE MASK • COLOR • AREA NO.0 - AERA NO.7 • ZONE MASKING • COLOR • AREA NO.0 - AERA NO.7 • STATUS HORIZON SIZE • VERTICAL SIZE • HORIZON MOVE • VERTICAL MOVEMOTION DETECTION• SENSITIVITY • AREA NO.0 - AERA NO.3 • ZONE MASKING • STATUS •COLOR • HORIZON SIZE • VERTICAL SIZE • HORIZON MOVE • VERTICAL MOVEVIDEO STANDARD • PAL • NTSCLANGUAGE • ENGLISH • CHINESELOAD DEFAULTSOFT VERSIONSAVE&EXITEXIT
MENU TREE SUMMARY
The OSD control may differ from show above, OSD buttons may replace the joystick type. Service cable output maybe not be available, and maybe optionally supplied with the product.
Highlight boxes below shows the menu path. Value ranges given in menu below are a guide for setting ranges, the camera osd will show only single values.
MAINMENU
IMAGE DAY&NIGHT AUTOZONE MASK MOTION DETECTION VIDEO STANDARD PALLANGUAGE ENGLISHLOAD DEFAULT SOFT VERSIONSAVE&EXITEXIT
MAINMENU
IMAGE DAY&NIGHT AUTOZONE MASK MOTION DETECTION VIDEO STANDARD PALLANGUAGE ENGLISHLOAD DEFAULT SOFT VERSIONSAVE&EXITEXIT
MAINMENU
IMAGE DAY&NIGHT AUTOZONE MASK MOTION DETECTION VIDEO STANDARD PALLANGUAGE ENGLISHLOAD DEFAULT SOFT VERSIONSAVE&EXITEXIT
IMAGE
3D-NR ONAE MODE GLOBALWB AWB-TEMPORALIMAGE ENHANCE MIRROR OFFFLIP OFFBRIGHTNESS 0~250ZOOM IN 0~5RETURN
IMAGE ENHANCE
SHARPNESS CONTRAST SATURATION RETURN
SHARPNESS
DETAIL MANUAL VALUE 0~15EDGE MANUAL VALUE 0~15RETURN
CONTRAST
CONTRAST MANUAL VALUE 0~255RETURN
SATURATION
SATURATION MANUAL VALUE 0~15RETURN
ZONE MASKING
COLOR MAGENTAAREA NO.0 AREA NO.1 AREA NO.2 AREA NO.3 AREA NO.4 AREA NO.5 AREA NO.6 AREA NO.7 RETURN
ZONE MASKING
STATUS OFFHORIZON SIZE 0~1280VERTICAL SIZE 0~720HORIZON MOVE 0~1280VERTICAL MOVE 0~720RETURN
MOTION DETECTION
SENSITIVITY HIGHAREA NO.0 AREA NO.1 AREA NO.2 AREA NO.3 RETURN
MOTION DETECTION
STATUS OFFCOLOR WHITEHORIZON SIZE 0~1280VERTICAL SIZE 0~720HORIZON MOVE 0~1280VERTICAL MOVE 0~720RETURN
9 10
TROUBLE SHOOTING NOTESFollow the steps below if you are experiencing trouble with your camera, before you contact your Technical Support.• Nothing appears on the screen.
¤ Check that the power cable is connected properly and that the voltage is correct. ¤ Check that you have properly connected VIDEO cable to the camera VIDEO output jack and to the
monitor/DVR.
• The image on the screen is unclear. ¤ Is the lens or dome cover stained with dirt? Clean lens or dome cover with soft, clean cloth. ¤ Re-position the camera if necessary. ¤ Adjust the Zoom and Focus screws as needed.
• The image on the screen is dark. ¤ If you have an intermediate device, set the impedance to 75Ω / Hi-z. ¤ Adjust the monitor contrast & brightness controls.
• Image quality is poor. ¤ Be sure to check cable for and braid which may be touching the common Coaxial core pin. ¤ Verify that the camera is receiving sufficient power.
• There is interference in the image. ¤ The camera or the cables may be close to a source of high voltage, such as a generator. Re-position
the camera if necessary.
When the resistance value of copper wire is at [20˚C(68˚F)]
Copper wire size (AWG) #24(0.22mm2) #22(0.33mm2) #20(0.52mm2) #18(0.83mm2)Resistance (Ω/m) 0.078 0.050 0.030 0.018Voltage Drop (V/m) 0.028 0.018 0.011 0.006
As shown in the table above, voltage decreases as the wire gets longer. Therefore use of an excessively long adapter output line for connection to the camera may affect the performance of the camera.
*Standard voltage for camera operation : DC12V ±10% or*There may be some deviation in voltage drop depending on the type of wire and the manufacturer.
• Be sure to connect power only after all the installation is complete.• Use the UL listed, CLASS 2 power transformer for 12v DC adapter.