Trinity Hydraulics - Catalog

CATALOGUE

P.O.Box: 8807, Dubai.Tel: 04-2853342, Fax: 04-2853347E-mail: [email protected]

Assembly and Supply of:

• Hydraulic Hoses and Fittings

• Stainless steel corrugated hoses and fittings

• Stainless steel expansion bellows

• Steel tubes, tube fittings & tube clamps

• Suction discharge, Air & Chemical hoses etc.

• Pressure guages, dowty seals, ball valves, quick release couplings etc.

Trinity Mechanical Services (Hydraulic Division)

STAINLESS STEEL EXPANSION BELLOW

Expansion control in pipelines, ducting and vessels which carry hot or cold fluids or which are exposed to the large variations in ambient temperature is a major problem confronting designers. As the metal temperature increases or decreases , the dimensional change due to thermal expansion or contraction will enduce excessive stresses in the piping , ducting or vessel and large forces will be transmitted to anchors and connected equipment. For controlling such stresses and bring them to allowable values for the materials used in piping, ducting, and vessels, several different methods are available , such as the use of pipebends and expansion loops. However the most modern designers prefer the use of metallic bellows expansion joints, because they require less space than bends and loops and because their inherent flexibility enables them to absorb movements in more than one direction , thereby permitting greater freedom in design. Furthermore , expansion joints prove to be more economical than other devices , so their use results in lower initial costs for piping and construction work, operating costs being reduced as well.

BELLOW ELEMENT.

The flexible element of an expansion joint, consisting of one or more convolutions obtained by the hydro-forming or mechanical forming according to the diameter of the shell of a material sutiable for the required specification. Bellows are welded to tube ends or flanges to constitute different models of expansion joint assemblies.

INNER SLEEVE.

A device which is also referred to as liner, telescopic sleeve etc, to avoid the head losses or turbulence and streamline the flow through bellows.It is required if the fluid flowing through the bellows is at very high velocity.

ENDS.

The ends of an expansion joint, which may be either equipped with flanges or suitably beveled for welding to adjacent equipment or piping etc.They are in compliance with applicable standards in force.Bellows offered by us are designed based on E.J.M.A guidelines and our stanadard range comprisesOf Bellows from 2inch to 72inch NB in single and multiply construction for different working temperatures , pressures and movements.The Cyclic life of a Bellow depends upon the extent to which It is stressed under optimum working Pressure, Temperature , Axial and Lateral deflection. To achieve a long life, a Bellow must be operated well within the maximum design parameters for both deflection and pressure.

AXIAL MOVEMENT.

The amount to motion parallel to the axis in a straight guided pipline.

LATERAL MOVEMENT.

A single plane deflection form the centre line of one end of the bellows but that end is keeping to remain parallel with the other end.

ANGULAR MOTION.

The ends are displaced at angle 0 to each other rather then remaining parallel.

TYPES OF EXPANSION JOINTS.

Some of the most common expansion joints being used for different applications are listed below.

AXIAL JOINTS.

This expansion joint is simply a bellows element with pipe ends or flanges connections.It is manufactured from Single and multiply elements. These bellows are suitable only for axial movements & also absorb limited lateral displacements. Tide Axial Expansion Joints also have one bellows except that their length is restrained tie rods.

UNIVERSAL EXPANSION JOINTS.

The universal expansion joint consists of two bellows separated by pipe section or spool. The primary purpose of this arrangement is to have a unit which will accept large amounts of lateral deflection. The amount of lateral deflection they can accept is a function of the amount of angulation.These joints have no restrains to resist pressure thrust like the axial. For given bellow element the amount of lateral deflection capability is increased or decreased by simply changing the length of the center spool.

Bellow expansion joints standard or custom designed are recommended for the following applications.

* Vaccum Steam * Petrochemical * Hot Water * Utilities * Solar * Environmental

Axil Movement

Lateral Movement

Angular Motion

Axil Joints

Universal Expansion Joints

Blocks

Now available with us

SAE O ñRING FLANGE CLAMPS AND BLOCK FLANGES.

We stock common range of SAE O ring split clamps and Block flange for Hydraulic Application.

* SAE O- Ring clamps and Blocks are available in different range and size.

* SAE O ñring Split Clamps

3000 PSI (61 code)

6000 PSI (62 code)

Code 61 and Code 62 SAE O ring Flange Blocks with NPT thread.

Code 61 and Code 62 SAE O ring Flange Blocks to Weld Socket.

Code 61 and Code 62 SAE Flat face flange Blocks with NPT thread.

Code 61 and Code 62 SAE Flat face flange Blocks to Weld Socket.Any other configurations are available on request.

STAINLESS STEEL CORRUGATED FLEXIBLE HOSES. HOSE Stainless Steel Corrugated flexible hoses are offered from 6mm (1/4” ) to 300mm(12”).The annular corrugated hose body provides the flexibility and pressure tight core of the assembly. BRAIDUnbraided corrugated hoses tend to elongate when pressurized above a certain level. To restrain this, an external layer of stainless steel wire braiding is provided on the hose. Braiding prevents longitudinal expansion of corrugated hose and thus increases the internal pressure strengthen of the hose many fold.Braiding is highly flexible and exactly follows the movements of the hose.To increase the pressure ratings further, two or even three layers of braiding are provided . Unless specified , braiding in high tensile stainless steel AISI 304 wire, will be supplied .

ASSEMBLIESStainless Steel hose assemblies are engineered to perfection in flexibility , strength and reliability. Hose assembly can be supplied with any types of end connections in various types of materials.The end connections are tig welded to hose.

ADVANTAGES OF FLEXIBLE METAL HOSES.• Suitableforwidetemperatuerange (-270 deg C to 700 deg C)• Compensatesforthermalexpansioncontraction in the piping system.• HighPhysicalStrength• FireResistant• MoistureResistant• LongerLife• GoodCorrosionCharacteristics• Resistanttoabrasion,penetrationanddamage• Connectsmisalignedrigidpipingabsorbsor dampens vibration and similar equipments.• Aflexibleandquickoptionforrigidpipingin difficult locations.

APPLICATIONS• CryogenicEquipment• NuclearPlants• Steam&HotWater• LubricationSystems• ChemicalIndustry• SteelIndustry• Food&BeverageIndustry• FertilizerIndustry• Sugar&PaperIndustry• AutomotiveExhaustSystems• Ships&Aircrafts• Airconditioning&RefrigerationSystems• GasBurnersystems• Compressedair&Pneumaticapplications.

P O Box 8807United Arab EmiratesE-mail : [email protected] :- 04-2853342Fax :- 04-2853347

HYDRAULICHOSES &

CONNECTORS

Uncontrolled distribution document

We reserve the right to make, without notice, changes to any drawing or data shown in this document because of technical development or other reason.Please note that all the shown compatibilities and conformities are geometrical ones, they do not necessarily imply performances compatibilites and conformities.

Catalogue

P O Box 8807, DubaiTrinity Mechanical Services (Hydraulic Division)

United Arab Emirates

Tel :- 04-2853342Fax :- 04-2853347

HYDRAULICHOSES &

CONNECTORS

Uncontrolled distribution document

We reserve the right to make, without notice, changes to any drawing or data shown in this document because of technical development or other reason.Please note that all the shown compatibilities and conformities are geometrical ones, they do not necessarily imply performances compatibilites and conformities.

Catalogue

2001

INDEX

1. HOSES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2. FERRULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3. HOSE CONNECTORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4. ADAPTORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5. STEEL TUBING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6. ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7. OTHER PRODUCTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8. TECHNICAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Page No.

1-10

11-12

13-27

28

29

30

31

32-36

HYDRAULIC HOSES 2001

HOSES

MIN BEND WEIGHT

ID OD RADIUS APPROX

MM MM PSI BAR PSI BAR MM KG/MTR

03 3/16 5 4.8 12.7 12,000 827 3,000 207 89 0.21004 1/4 6 6.3 15.9 11,000 758 2,750 190 102 0.30005 5/16 8 7.9 17.5 10,000 690 2,500 172 114 0.35006 3/8 10 9.5 19.8 9,000 620 2,250 155 127 0.43008 1/2 12 12.7 23 8,000 552 2,000 138 178 0.53010 5/8 16 15.9 26.2 6,000 414 1,500 103 203 0.62012 3/4 20 19.1 30.2 5,000 345 1,250 86 241 0.76016 1 25 25.4 38.1 4,000 276 1,000 69 305 1.13020 1 1/4 32 31.8 46 2,500 172 625 43 419 1.42024 1 1/2 40 38.1 52.4 2,000 138 500 34 508 1.77032 2 50 50.8 66.7 1,500 103 375 26 635 2.460

Application : High pressure Hydraulic systems using mineral oils, glycols and acqueous oils

Construction : Tube - Oil resistant synthetic rubber

Reinforcement-1 high tensile steel braid

Cover - synthetic rubber with high abrasion ozone and weather resistance

Temperature range : - 40º C to +110º C

HOSES

MIN BEND WEIGHT

ID OD RADIUS APPROX


03 3/16 5 4.8 15.9 20,000 1,380 5,000 345 89 0.36004 1/4 6 6.3 17.5 20,000 1,380 5,000 345 102 0.47005 5/16 8 7.9 19.1 17,000 1,172 4,250 293 114 0.51006 3/8 10 9.5 21.4 16,000 1,103 4,000 276 127 0.63008 1/2 12 12.7 24.6 14,000 965 3,500 241 178 0.73510 5/8 16 15.9 27.8 11,000 758 2,750 190 203 0.85012 3/4 20 19.1 31.8 9,000 620 2,250 155 241 1.06016 1 25 25.4 39.7 8,000 552 2,000 138 305 1.51520 1 1/4 32 31.8 50.8 6,500 448 1,625 112 419 2.35024 1 1/2 40 38.1 57.2 5,000 345 1,250 86 508 2.70032 2 50 50.8 69.8 4,500 310 1,125 78 635 3.345

Application : High pressure Hydraulic systems using mineral oils, glycols and acqueous emulsion oils





HYDRAULIC HOSES

SAE 100R1AT-HOSECODE

SAE 100R2AT-HOSE

HR1T

HR2T

HOSE

NOM SIZE

MIN ACTUAL

BURST PRESSURE

CODE NOM SIZE

DN

MIN ACTUAL

BURST PRESSURE

HOSE

DN

WORKING

PRESSURE

WORKING

PRESSURE

1

1

HYDRAULIC HOSES

HOSES

MIN BEND WEIGHT

ID OD RADIUS APPROX

MM MM PSI BAR PSI BAR PSI BAR MM KG/MTR

03 3/16 5 4.8 12 16,665 1,150 14,500 1000 3,625 250 90 0.19004 1/4 6 6.3 14 14,500 1,000 13,050 900 3,260 225 100 0.24005 5/16 8 8.0 15 13,050 900 12,325 850 3,120 215 115 0.28006 3/8 10 9.5 17.5 11,600 800 10,440 720 2,610 180 130 0.36008 1/2 12 12.7 21 9,860 680 9,280 640 2,320 160 180 0.45010 5/8 16 16.0 24 8,700 600 7,540 520 1,885 130 200 0.51012 3/4 20 19.0 28 7,250 500 6,090 420 1,525 105 240 0.65016 1 25 25.4 36 5,220 360 5,075 350 1,275 88 300 0.96020 1 1/4 32 31.8 43.5 5,075 350 3,625 250 915 63 420 1.25024 1 1/2 40 38.1 50 4,060 280 2,900 200 725 50 500 1.60032 2 50 50.8 63.5 3,625 250 2,320 160 580 40 630 2.200

Application : High pressure hydraulic systems using mineral oils, glycols and acqueous emulsion oils.



Cover - synthetic rubber with high abrasion, ozone and weather resistance


Special Characteristic : The impulse performance is higher than DIN-SAE specs., allowing improved and long lasting operating performances with good flexibility.

HOSES

MIN BEND WEIGHT

ID OD RADIUS APPROX


03 3/16 5 4.8 13.7 29,000 2,000 23,925 1650 6,020 415 90 0.32004 1/4 6 6.3 15.5 25,375 1,750 23,200 1600 5,800 400 100 0.37005 5/16 8 8.0 16.5 21,460 1,480 20,300 1400 5,075 350 115 0.41206 3/8 10 9.5 19.5 20,300 1,400 19,140 1320 4,785 330 130 0.53008 1/2 12 12.7 22.5 16,965 1,170 15,950 1100 3,990 275 180 0.64010 5/8 16 16.0 25.5 14,790 1,020 14,500 1000 3,625 250 200 0.77012 3/4 20 19.0 29.5 13,050 900 12,325 850 3,120 215 240 0.96016 1 25 25.4 38 9,715 670 9,425 650 2,390 165 300 1.35020 1 1/4 32 31.8 48 8,700 600 7,250 500 1,815 125 420 2.05024 1 1/2 40 38.1 55 7,250 500 5,220 360 1,305 90 500 2.51132 2 50 50.8 67 6,090 420 4,640 320 1,160 80 630 3.160

Application : High pressure Hydraulic systems using mineral oils glycols and acqueous oils





Special Characteristic : The impulse performance is higher than DIN-SAE spec., allowing improved and long lasting operating

performance with good flexibility

HYDRAULIC HOSES

WORKING

PRESSURE

SPEC BURST

PRESSURE

SPEC BURST

PRESSURE

WORKING

PRESSURE

SAE 100R1AT-DIN20022 1SN

HOSE

SAE 100R2AT-DIN20022 2SN

HOSE CODE

HR1T

HR2T

HOSE

HOSE

NOM SIZE

DN

MIN ACTUAL

BURST PRESSURE

CODENOM SIZE

DN

MIN ACTUAL

BURST PRESSURE

2

2001


HOSES

MIN BEND WEIGHT

ID OD RADIUS APPROX


03 3/16 04 4.8 13.2 14,500 1,000 12,000 827 3,000 207 76 0.21004 1/4 05 6.3 15.0 13,340 920 12,000 827 3,000 207 86 0.26505 5/16 06 8.0 17.0 11,600 800 9,000 621 2,250 155 102 0.33507 13/32 07 10.5 19.5 10,875 750 8,000 552 2,000 138 117 0.39008 1/2 08 12.7 23.5 8,265 570 7,000 483 1,750 121 140 0.52510 5/8 10 16.0 27.5 7,250 500 6,000 414 1,500 103 165 0.65014 7/8 16 22.0 31.5 4,785 330 3,200 221 800 55 183 0.66018 1 1/8 20 28.0 38.0 5,220 360 2,500 172 625 43 229 0.91022 1 3/8 24 35.0 44.5 4,640 320 2,000 138 500 34 267 1.00029 1 13/16 32 46.0 56.4 3,625 250 1,400 97 350 24 337 1.480

Application : High pressure Hydraulic systems using mineral oils, glycols and acqueous emulsion oils


Reinforcement-1 textile braid, 1 steel braid

Cover - a textile braid embedded with synthetic rubber


Special Characteristic : The hose conforms to SAE 100R5 spec. and the construction makes the hose particularly suitable for tough operating conditions.

HOSES

MIN BEND WEIGHT

ID OD RADIUS APPROX

MM MM PSI PSI BAR SI PSI BAR PSI MM KG/MTR

04 1/4 4 6.3 12.5 1,600 110 400 28 64 0.15005 5/16 5 8.0 14.0 1,600 110 400 28 76 0.16506 3/8 6 9.5 16.0 1,600 110 400 28 76 0.20008 1/2 8 12.7 19.8 1,600 110 400 28 102 0.26010 5/8 10 16.0 23.0 1,400 97 350 24 127 0.32012 3/4 12 19.0 26.0 1,400 97 350 24 140 0.38016 1 16 25.4 32.0 1,400 97 350 24 152 0.465

Application : Low pressure hydraulic systems using mineral oils, glycols and acqueous emulsion oils.


Reinforcement-1 high tensile textile braid



Special Characteristic : The hose conforms to SAE 100R6, the special reinforcement used makes the hose particularly reliable when operating at high pressure

and high temperature.

HYDRAULIC HOSES

SPEC BURST

PRESSURE

WORKING

PRESSURE

SPEC BURST

PRESSURE

WORKING

PRESSUREDASH

NOM SIZE

HOSE

NOM SIZE

DASH

SAE 100R5 - HOSE

SAE 100R6-HOSECODE

HR5

HR6

HOSE MIN ACTUAL

BURST PRESSURECODE

3


HOSES

MIN BEND WEIGHT

ID OD RADIUS APPROX


03 3/16 03 4.8 9.7 12,000 827 3,000 207 20 0.06504 1/4 04 6.3 12.1 11,000 758 2,750 190 32 0.09805 5/16 05 8.0 14.0 10,000 689 2,500 172 45 0.11806 3/8 06 9.5 16.1 9,000 620 2,250 155 51 0.14408 1/2 08 12.7 19.4 8,000 552 2,000 138 77 0.21112 3/4 12 19.0 27 5,000 345 1,250 86 127 0.259

(Twin hoses also available)

Construction : Core - superpolyamide

Reinforcement-1 synthetic fibre braid

Cover - polyurethane


Special Characteristic : Small outside diameter, wide fluid compatibility and lightweight.

HOSES

MIN BEND WEIGHT

ID OD RADIUS APPROX

MM MM PSI PSI BAR SI PSI BAR PSI MM KG/MTR

04 1/4 04 6.3 15.8 20,000 1,379 5,000 345 51 0.17606 3/8 06 9.5 19.35 16,000 1,103 4,000 276 64 0.22008 1/2 08 12.7 22.5 14,000 965 3,500 241 102 0.283

Construction : Core - superpolyamide

Reinforcement-2 synthetic fibre braids

Cover - polyurethane


Special Characteristic : Lightweight and compact, wide fluid compatibility

HYDRAULIC HOSES

WORKING

PRESSURE

SPEC BURST

PRESSURE

WORKING

PRESSURE

HOSE

HOSE

CODENOM SIZE DASH

SAE 100R7 - HOSE

SAE 100R8-HOSE

HR7

HR8

CODENOM SIZE

MIN ACTUAL

BURST PRESSURE

DASH

4


HOSES

MIN BEND WEIGHT

ID OD RADIUS APPROX


03 3/16 03 4.75 9.40 20,000 1,379 5,000 345 75 0.10004 1/4 04 6.35 11.68 17,000 1,172 4,250 293 100 0.18506 3/8 06 9.53 15.75 13,000 896 3,250 224 125 0.24008 1/2 08 12.70 18.29 11,000 760 2,750 190 180 0.370

Construction : Core - polyester elastomer


Cover - polyester elastomer


Special Characteristic : The polyester elastomer core and cover gives excellent resistance to almost all paint solvents

HOSES

MIN BEND WEIGHT

ID OD RADIUS APPROX


04 1/4 04 6.35 13.72 26,000 1,792 6,500 448 100 0.30006 3/8 06 9.53 17.02 20,000 1,380 5,000 345 125 0.45008 1/2 08 12.70 21.21 16,000 1,104 4,000 276 180 0.610

Construction : Core - polyester elastomer

Reinforcement- 2 high tensile steel braids

Cover - polyester elastomer


Special Characteristic : The polyester elastomer core and cover gives excellent resistance to almost all paint solvents

HYDRAULIC HOSES

WORKING

PRESSURE

SINGLE WIRE BRAID

THERMOPLASTIC HOSE

HTP1

HOSE

DOUBLE WIRE BRAID

THERMOPLASTIC HOSE

HOSE

CODE

WORKING

PRESSURENOM SIZE

DASH

CODE

MIN ACTUAL

BURST PRESSURE

MIN ACTUAL

BURST PRESSURENOM SIZE

DASH

5

HTP2


HOSES

MIN BEND WEIGHT

ID OD RADIUS APPROX


04 1/4 6 6.3 17.8 34,800 2,400 26,100 1,800 6,525 450 150 0.62006 3/8 10 9.5 21.4 30,450 2,100 25,810 1,780 6,450 445 180 0.77008 1/2 12 12.7 24.6 27,550 1,900 24,070 1,660 6,020 415 230 0.92010 5/8 16 16.0 28.5 23,200 1,600 20,300 1,400 5,075 350 250 1.12012 3/4 20 19.0 32.0 23,000 1,600 20,300 1,400 5,075 350 300 1.56016 1 25 25.4 39.7 21,750 1,500 16,240 1,120 4,060 280 340 2.06020 1 1/4 32 31.8 50.8 18,125 1,250 12,180 840 3,045 210 457 3.31024 1 1/2 40 38.1 57.0 14,500 1,000 10,730 740 2,685 185 559 3.81032 2 50 50.8 70.6 14,500 1,000 9,570 660 2,395 165 660 5.350

Application : Very high pressure hydraulic systems using hydraulic oils


Reinforcement-4 high tensile steel spirals

Cover - synthetic rubber with high temperature, ozone and abrasion resistance


HOSES

MIN BEND WEIGHT

ID OD RADIUS APPROX


16 1 25 25.4 39.2 23,925 1,650 20,000 1,379 5,000 345 305 2.28020 1 1/4 32 32.0 49.8 21,025 1,450 20,000 1,379 5,000 345 419 3.71024 1 1/2 40 38.0 57.3 21,750 1,500 20,000 1,379 5,000 345 508 4.96032 2 50 50.8 71.0 20,300 1,400 20,000 1,379 5,000 345 635 7.360



Reinforcement-4 high tensile steel spirals upto 1" bore, and six spirals from 1 1/4" bore and above



HYDRAULIC HOSES

SAE 100R9R - DIN 20023 4SP HOSE

HR9R

HR13

HOSE

SAE 100R13 HOSE HOSE

CODE

CODENOM SIZE

DN

SPEC BURST

PRESSURE

MIN ACTUAL

BURST PRESSURENOM SIZE

DN

MIN ACTUAL

BURST PRESSURE

WORKING

PRESSURE

SPEC BURST

PRESSURE

WORKING

PRESSURE

6


HOSES

MIN BEND WEIGHT

ID OD RADIUS APPROX


16 1 25 25.4 38.0 25,375 1,750 22,040 1,520 5,510 380 340 2.08020 1 1/4 32 31.8 45.2 20,300 1,400 18,850 1,300 4,715 325 460 2.51024 1 1/2 40 38.1 53.5 17,400 1,200 16,820 1,160 4,205 290 560 3.42032 2 50 50.8 68.0 15,950 1,110 14,500 1,000 3,625 250 700 4.730






MIN ACTUAL

BURST PRESSURE

SPEC BURST

PRESSURE

WORKING

PRESSURE

DIN 20023 4SH HOSE

H4SH

HOSE

CODENOM SIZE DN

HOSES

MIN BEND WEIGHT

ID OD RADIUS APPROX


04 1/4 6 6.35 17.80 36,250 2,500 14,500 1,000 150 0.6006 3/8 10 9.50 23.80 36,250 2,500 14,500 1,000 200 1.1408 1/2 12 12.70 23.10 36,250 2,500 14,500 1,000 240 1.3412 3/4 20 19.05 32.20 36,250 2,500 14,500 1,000 305 2.51

Construction : Tube - water and Oil resistant synthetic rubber



Temperature range : -40º C to +100º C

HYDRAULIC HOSES

PRESSURE

WORKING

PRESSURECODENOM SIZE

WATER BLAST HOSE

DN

HOSE SPEC BURST

HRWB

7


HOSES

MAX. WORKING MIN BEND WEIGHT

PRESSURE AT 20 C PRESSURE AT 20 C RADIUS APPROX

in mm MIN MAX PSI MIN MAX PSI BAR PSI BAR MM KG/MTR

02 1/8 3.5 3.4 3.70 5.9 6.3 4,205 290 12,615 870 22 0.06503 3/16 4.5 4.4 4.75 6.9 7.3 3,845 265 11,530 795 40 0.08004 1/4 6.3 6.0 6.50 8.3 8.7 3,480 240 10,440 720 60 0.09305 5/16 8.0 7.5 8.00 9.8 10.3 2,900 200 8,700 600 70 0.11006 3/8 9.5 9.1 9.60 11.5 12.0 2,755 190 8,265 570 80 0.12408 1/2 12.7 11.9 12.80 14.5 15.4 2,175 150 6,525 450 110 0.20710 5/8 16.0 15.0 16.00 17.8 18.9 1,595 110 4,785 330 150 0.25512 3/4 19.0 18.0 19.20 21.0 22.3 1,160 80 3,480 240 200 0.31516 1 25.4 24.0 25.40 27.6 28.7 800 55 2,400 165 300 0.430

Construction The hose has a smooth innercore of extruded white Teflon with a single 304 stainless steel wire braid reinforcement

Temperature range -54º C to +232º C for continuous service

-73º C to +260º C for intermittent service

HOSES

MIN BEND WEIGHT

ID OD RADIUS APPROX


06 3/8 10 9.5 20.0 23,200 1,600 16,000 1,103 4,000 276 127 0.62008 1/2 12 12.7 23.8 19,575 1,350 16,000 1,103 4,000 276 178 0.80012 3/4 20 19.0 30.7 20,300 1,400 16,000 1,103 4,000 276 241 1.22016 1 25 25.4 38.0 21,025 1,450 16,000 1,103 4,000 276 305 2.05020 1 1/4 32 31.8 47.0 17,400 1,200 12,000 827 3,000 207 419 2.810024 1 1/2 40 38.1 53.5 11,600 800 10,000 690 2,500 172 508 3.32032 2 50 50.8 66.7 11,600 800 10,000 690 2,500 172 635 4.620






Special Characteristic : The hose exceeds SAE 100R12 spec., particularly on the impulse and burst pressures.

HYDRAULIC HOSES

BORE SIZE iNTERNAL DIA

HOSE

OUTSIDE DIA

MM MMCODE

HSST

SAE 100 R12 HOSECODE

HR12

NOM SIZE

DN

MIN ACTUAL

BURST PRESSURE

MIN BURST

SPEC BURST

PRESSURE

WORKING

PRESSURE

P.T.F.E hose has outstanding properties which are unmatched by any other flexible hose. It is possible to greatly reduce (or completely eliminate) maintenance and replacement costs which occur with conventional hoses used in extremely adverse conditions on various industrial applications. Within its working temperature range P.T.F.E. is completely inert to most known chemicals including alcohols, ehtylene glycol, concentrated acids, oils and fuels. P.T.F.E. hose has been tested and recommended for such aggressive acids, gases and solvents as nitrogen, hydrogen, ammonia, freons, butane, propane, chlorine, benzene, toluene, xylene, carbon tetrachloride, trichlorethylene, esters, ketones, hot fuming nitric, sulphuric and hydrochloric acid, concenrated sodium hydroxide, ammonia hydroxide and steam. Exceptions are few and comprise molten alkali metals and elementary flourine at elevated temperatures and pressures. P.T.F.E. will not cause contamination and can be handled with complete safety within its working temperature limits.

8

STAINLESS STEELTEFLON HOSE


HOSES

MIN BEND WEIGHT

ID OD RADIUS APPROX


04 1/4 6 6.3 16.0 14,500 1,000 13,050 900 3,335 230 100 0.32005 5/16 8 8.0 17.5 12,835 885 12,325 850 3,045 210 114 0.34506 3/8 10 9.5 20.0 11,385 785 10,440 720 3,045 210 127 0.44508 1/2 12 12.7 21.0 9,860 680 9,280 640 2,320 160 178 0.540





HOSES

MIN BEND WEIGHT

ID OD RADIUS APPROX


05 5/16 8 8.0 19.0 21,315 1,470 20,300 1400 5,800 400 114 0.51006 3/8 10 9.5 21.5 19,575 1,350 19,140 1320 5,800 400 127 0.63008 1/2 12 12.7 24.5 16,675 1,150 15,950 1100 4,060 280 178 0.775





HYDRAULIC HOSES

BURST PRESSURE

SPEC BURST

PRESSURE

WORKING

PRESSURENOM SIZE

DASH

MIN ACTUAL SPEC BURST

PRESSUREBURST PRESSURE

WORKING

PRESSURE

MIN ACTUAL

SINGLE WIRE BRAID JETWASH

HOSE

R1A-SH

R2A-SH

HOSE

DOUBLE WIRE BRAID JETWASH

HOSE

HOSE

CODENOM SIZE

DIN

CODE

9


HOSES

WEIGHT

STATIC FLEXING PRESSURE AT 20º C APPROX

MM IN MM IN PSI MM MM BAR PSI BAR PSI KG/MTR

04 6.3 1/4 14.4 0.567 25 100 142 2,060 568 8,240 0.2906 9.5 3/8 19.4 0.763 40 150 104 1,510 416 6,040 0.4308 12.7 1/2 23.4 0.922 50 150 92 1,325 366 5,300 0.5312 19.0 3/4 29.6 1.170 70 200 70 1,010 278 4,040 0.7516 25.4 1 37.1 1.460 90 200 71 1,025 282 4,100 1.0020 31.8 1 1/4 48.5 1.910 108 250 45 653 180 2,610 1.3024 38.1 1 1/2 56.6 2.230 127 250 41 595 164 2,380 1.7032 50.8 2 67.8 2.670 175 350 31 440 122 1,760 1.9040 63.5 2 1/2 87.6 3.450 200 410 26 370 102 1,480 2.8048 76.2 3 99.8 3.930 200 450 19 280 76 1,120 3.3064 101.6 4 129.0 5.080 230 560 18 267 73 1,068 4.6096 152.4 6 180.0 7.100 320 815 11 162 45 648 7.70

Construction : Butt welded annular corrugated flexible stainless steel (type 316L and 321) tubing with a single stainless steel wire braid.

Temperature range : -200º C to +600º C (type 316L +420º C)

HOSES

WEIGHT

STATIC FLEXING PRESSURE AT 20º C PRESSURE AT 20º C APPROX

MM IN MM IN MM MM BAR PSI BAR PSI KG/MTR

04 6.3 1/4 15.8 0.622 25 100 255 3,700 1,020 14,800 0.3906 9.5 3/8 21.0 0.826 40 150 187 2,710 748 10,480 0.5908 12.7 1/2 25.0 0.985 50 150 165 2,400 660 9,600 0.7312 19.0 3/4 31.2 1.230 70 200 125 1,810 500 7,240 1.1016 25.4 1 39.2 1.540 90 200 120 1,740 480 6,960 1.5020 31.8 1 1/4 50.6 1.990 108 250 80 1,160 320 4,640 1.9024 38.1 1 1/2 58.7 2.310 127 250 71 1,030 284 4,120 2.4032 50.8 2 69.9 2.750 175 350 50 725 200 2,900 2.6040 63.5 2 1/2 89.7 3.530 200 410 46 667 184 2,668 3.8048 76.2 3 102.0 4.010 200 450 34 493 136 1,972 4.4064 101.6 4 132.0 5.180 230 560 33 480 132 1,920 6.4096 152.4 6 183.0 7.200 320 815 20 290 80 1,160 9.90

Construction : Butt welded annular corrugated flexible stainless steel (type 316L and 321) tubing with a double stainless steel wire braid.

Temperature range : -200º C to +600º C (type 316L +420º C)

HYDRAULIC HOSES

MIN BURST

MIN BURSTMAX. WORKING

MAX. WORKING

PRESSURE AT 20º C

MIN BEND RADIUS

DIAMETERCODE

HSPF2

NOMINAL ID MAX HOSE OD

Hoses are designed to withstand extremes of operating temperatures under arduous conditions. Flexibility is excellent and this tubing will workunder conditions where extreme vibration is encountered,minimum bend radii are very low and the tubing is non-magnetic. The hose is suitablefor exhaust and corrosive fluids, steam, acids and solvents, radioactive gases and fluids, chemical gases, petrol and many alkalis, acids, etc.

SINGLE WIRE BRAID STAINLESS

STEEL CONVOLUTED

HOSE

HSPF1

DOUBLE WIRE BRAID STAINLESS

STEEL CONVOLUTED

HOSE

NOMINAL ID

CODE

MAX HOSE OD

DIAMETER

MIN BEND RADIUS

10

HOSE CONNECTORS 2001

FERRULES

Hose I.D. Dimensions(mm)

DN mm SIZE Inch D L

O3 5 4.8 03 3/16" 19 26

O4 6 6.3 04 1/4" 20 30.5

O5 8 7.9 05 5/16" 22 30.5

O6 10 9.5 06 3/8" 24 31.5

O8 12 12.7 08 1/2" 28.5 34

10 16 15.9 10 5/8" 32 37

12 20 19.1 12 3/4" 36 42.5

16 25 25.4 16 1" 43 50

20 32 31.8 20 1 1/4" 53 59


DN mm SIZE Inch D L

HSN2 O4 6 6.3 04 1/4" 22 30.5

O5 8 7.9 05 5/16" 24 30.5

O6 10 9.5 06 3/8" 25.5 31.5

O8 12 12.7 08 1/2" 30 34

10 16 15.9 10 5/8" 34 37

12 20 19.1 12 3/4" 38 42.5

16 25 25.4 16 1" 46 50


DN mm SIZE Inch D L

HSP1 O3 5 4.8 03 3/16" 14 27

O4 6 6.3 04 1/4" 17 29

O5 8 7.9 05 5/16" 19 30

O6 10 9.5 06 3/8" 21 31

O8 12 12.7 08 1/2" 25.5 34

10 16 15.9 10 5/8" 28.5 36

12 20 19.1 12 3/4" 32 42

16 25 25.4 16 1" 40 50

HOSE CONNECTORS

1 WIRE FERRULES CODE

HSN1

2 WIRE FERRULES CODE

R7 FERRULES CODE

11



DN mm SIZE Inch D L

O4 6 6.3 04 1/4" 22 30

O6 10 9.5 06 3/8" 25.5 33.5

O8 12 12.7 08 1/2" 30 37

10 16 15.9 10 5/8" 34 40

12 20 19.1 12 3/4" 38 43

16 25 25.4 16 1" 46 60

20 32 31.8 20 1 1/4" 56 66

24 40 38.1 24 1 1/2" 65 76.5

32 50 50.8 32 2" 80 80


DN mm SIZE Inch D L

16 25 25.4 16 1" 46 75

20 32 31.8 20 1 1/4" 60 88

24 40 38.1 24 1 1/2" 67 94

32 50 50.8 32 2" 84.5 99

HOSE CONNECTORS

HEH

HMS

CODE4 WIRE FERRULES

6 WIRE EXTRA HIGH PRESSURE FERRULES

CODE

12


HA10 B.S.P. MALE PARALLEL - 60° CONE SEAT

Hose I.D. Thread Dimensions(mm)

DN mm SIZE Inch F H L S

O4 6 6.30 04 1/4" 1/4"-19 26.0 54.5 19

O6 10 9.50 06 3/8" 3/8"-19 28.5 59.0 22

O8 12 12.70 08 1/2" 1/2"-14 33.0 66.0 27

10 16 15.90 10 5/8" 5/8"-14 35.0 71.0 30

12 20 19.10 12 3/4" 3/4"-14 39.0 80.0 32

16 25 25.40 16 1" 1"-11 43.5 98.5 41

20 32 31.80 20 1 1/4" 1 1/4"-11 47.0 108.0 50

24 40 38.10 24 1 1/2" 1 1/2"-11 51.0 121.5 55

32 50 50.80 32 2" 2"-11 53.5 129.5 70

HA22 B.S.P. TAPER MALE - 60° CONE SEAT



O4 6 6.3 04 1/4" 1/4"-19 26.7 55.2 15

O6 10 9.5 06 3/8" 3/8"-19 27.8 58.3 19

O8 12 12.7 08 1/2" 1/2"-14 34.5 67.5 22

12 20 19.1 12 3/4" 3/4"-14 37.2 78.2 27

16 25 25.4 16 1" 1"-11 44.0 99.0 36

20 32 31.8 20 1 1/4" 1 1/4"-11 48.1 109.1 46

24 40 38.1 24 1 1/2" 1 1/2"-11 49.9 120.4 50

32 50 50.8 32 2" 2"-11 55.2 131.2 65

HA17 B.S.P. FEMALE - 60° CONE


DN mm SIZE Inch F H L G S

O4 6 6.3 04 1/4" 1/4"-19 18.7 47.2 4.1 19

O6 10 9.5 06 3/8" 3/8"-19 19.7 50.2 5.8 22

O8 12 12.7 08 1/2" 1/2"-14 22.7 55.7 6.5 27

10 16 15.9 10 5/8" 5/8"-14 22.7 58.7 9.3 30

12 20 19.1 12 3/4" 3/4"-14 26.1 67.1 8.6 32

16 25 25.4 16 1" 1"-11 29.8 84.8 10.5 41

20 32 31.8 20 1 1/4" 1 1/4"-11 32.9 93.9 10.0 50

24 40 38.1 24 1 1/2" 1 1/2"-11 36.0 12.0 55

32 50 50.8 32 2" 2"-11 37.0

106.5

113.0 16.0 70

HOSE CONNECTORS

BSP FEMALE STANDARD CODE

CODE

CODE

BSP MALE PARALLEL

BSPT MALE

13


HB1790° B.S.P. COMPACT ELBOW - 60° CONE

SOLID - CRIMPED NUT


DN mm SIZE Inch F H L K G S S1

O4 6 6.3 04 1/4" 1/4"-19 18.5 47.0 22.0 4.1 19.0 14.0

O6 10 9.5 06 3/8" 3/8"-19 20.0 50.5 24.5 5.8 22.0 17.0

O8 12 12.7 08 1/2" 1/2"-14 24.0 57.0 29.0 6.5 27.0 22.0

HG17 B.S.P. 90° SWEPT ELBOW - 60° CONE - SOLID


DN mm SIZE Inch F H L K G S

O4 6 6.3 04 1/4" 1/4"-19 24.0 52.0 28.0 4.1 19.0

O6 10 9.5 06 3/8" 3/8"-19 34.0 64.0 36.5 5.8 22.0

O8 12 12.7 08 1/2" 1/2"-14 41.0 74.0 44.0 6.5 27.0

10 16 15.9 10 5/8" 5/8"-14 49.0 85.0 50.5 9.3 30.0

12 20 19.1 12 3/4" 3/4"-14 58.0 99.0 60.5 8.6 32.0

16 25 25.4 16 1" 1"-11 74.0 129.0 72.5 10.5 41.0

20 32 31.8 20 1 1/4" 1 1/4"-11 72.0 153.0 89.0 10.0 50.0

24 40 38.1 24 1 1/2" 1 1/2"-11 108.0 179.0 101.5 12.0 55.0

32 50 50.8 32 2" 2"-11 142.0 218.0 217.5 16.0 70.0

HJ17 B.S.P. 45° SWEPT ELBOW - 60° CONE - SOLID


DN mm SIZE Inch F H L K G S S1

O4 6 6.3 04 1/4" 1/4"-19 40.0 68.5 16.5 4.1 19.0

O6 10 9.5 06 3/8" 3/8"-19 53.5 84.0 19.5 5.8 22.0

O8 12 12.7 08 1/2" 1/2"-14 64.0 97.0 24.5 6.5 27.0

10 16 15.9 10 5/8" 5/8"-14 78.5 114.5 26.0 9.3 30.0

12 20 19.1 12 3/4" 3/4"-14 88.5 129.5 35.0 8.6 32.0

16 25 25.4 16 1" 1"-11 110.0 165.0 42.0 10.5 41.0

20 32 31.8 20 1 1/4" 1 1/4"-11 138.0 199.0 54.5 10.0 50.0

24 40 38.1 24 1 1/2" 1 1/2"-11 162.0 232.5 58.5 12.0 55.0

32 50 50.8 32 2" 2"-11 205.5 281.5 66.5 16.0 70.0

HOSE CONNECTORS

CODE

BSPF 45 DEG STANDARD

CODE

BSPF 90 DEG COMPACT

BSPF 90 DEG STANDARD

CODE

14


HA19B.S.P. FEMALE - FLAT FACE

PRESSED NUT


DN mm SIZE Inch F H L G S

O4 6 6.3 04 1/4" 1/4"-19 15.5 44 7 19

06 10 9.5 06 3/8" 3/8"-19 16.5 47 9 22

O8 12 12.7 08 1/2" 1/2"-14 19.2 52.2 10 27

10 16 15.9 10 5/8" 5/8"-14 20.5 56.5 11.5 30

12 20 19.1 12 3/4" 3/4"-14 22.7 63.7 12 32

16 25 25.4 16 1" 1"-11 26.3 81.3 14 41

HA34 N.P.T.F. MALE - 60° CONE SEAT



O4 6 6.3 04 1/4" 1/4"-18 26.5 55 15

O6 10 9.5 06 3/8" 3/8"-18 27.5 58 19

O8 12 12.7 08 1/2" 1/2"-14 34.5 67.5 22

12 20 19.1 12 3/4" 3/4"-14 37.2 78.2 27

16 25 25.4 16 1" 1"-11,5 43.5 98.5 36

20 32 31.8 20 1 1/4" 1 1/4"-11,5 46.1 107 46

24 40 38.1 24 1 1/2" 1 1/2"-11,5 54 112 53

32 50 50.8 32 2" 2"-11,5 57 130 65

HOSE CONNECTORS

CODE

BSPF FLAT FACE

NPT MALE STANDARD

CODE

15


HA38STRAIGHT SAE J518 FLANGE - 3000 PSI

SOLID


DN mm SIZE Inch H L A

O8 12 12.7 08 1/2" 1/2" 48.5 81.5 30.2

12 20 19.1 12 3/4" 3/4" 53.5 94.5 38.1

16 25 25.4 16 1" 1" 60.5 115.5 44.5

20 32 31.8 20 1 1/4" 1 1/4" 65.5 126.5 50.8

24 40 38.1 24 1 1/2" 1 1/2" 70.5 141.0 60.3

32 50 50.8 32 2" 2" 77.0 153.0 71.4

STRAIGHT KOMATSU FLANGE - SOLID

10 16 15.9 10 5/8" 5/8" 49.3 85.3 34

HG3890° SAE J518 FLANGE - 3000 PSI

SOLID


DN mm SIZE Inch H L K A

O8 12 12.7 08 1/2" 1/2" 41 74 42 30.2

12 20 19.1 12 3/4" 3/4" 58 99 57 38.1

16 25 25.4 16 1" 1" 74 129 69 44.5

20 32 31.8 20 1 1/4" 1 1/4" 92 153 87 50.8

24 40 38.1 24 1 1/2" 1 1/2" 108 179 101 60.3

32 50 50.8 32 2" 2" 142 218 134 71.4

90° KOMATSU FLANGE - SOLID

10 16 15.9 10 5/8" 5/8" 49 85 49 34

HOSE CONNECTORS

FLANGE

FLANGE

SAE FLANGE 3000 PSI 90 DEG STANDARD CODE

SAE FLANGE 3000PSI STANDARD

CODE

16


HJ3845° SAE J518 FLANGE - 3000 PSI

ONE PIECE



O8 12 12.7 08 1/2" 1/2" 62.0 95 22.5 30.2

12 20 19.1 12 3/4" 3/4" 86.5 128 33 38.1

16 25 25.4 16 1" 1" 107.5 163 39.5 44.5

20 32 31.8 20 1 1/4" 1 1/4" 136.5 198 53 50.8

24 40 38.1 24 1 1/2" 1 1/2" 162.0 233 58.5 60.3

32 50 50.8 32 2" 2" 210.5 287 71.5 71.4

HZF38SAE J518 SPLIT FLANGE HALF

3000 PSI

Dimensions(mm)

B D E F I

O8 23.8 9 9.15 15.9 22.2

12 30.2 11 11.90 19 28.6

16 34.9 13 13.90 22.2 36.5

20 38.9 15 15.80 23.8 39.7

24 47.6 17 18.20 27 46

32 57.1 21 22.20 36.5 55.6

HOSE CONNECTORS

1 1/2"

2"

1/2"

3/4"

1"

1 1/4"

112.7 69.9

133.3 77.8

80.9 52.4

95.2 58.7

FLANGE

SPLIT FLANGE 3000PSI

CODE

SAE FLANGE 45 DEG 3000 PSI

CODE

FLANGE

C

56.3

71.4 47.6

A

17

38.1


HA39STRAIGHT SAE J518 FLANGE - 6000 PSI

ONE PIECE


DN mm SIZE Inch H L A

O8 12 12.7 08 1/2" 1/2" 49.5 82.5 31.7

12 20 19.1 12 3/4" 3/4" 60.0 101.0 41.3

16 25 25.4 16 1" 1" 66.5 121.5 47.6

20 32 31.8 20 1 1/4" 1 1/4" 71.0 132.0 54.0

24 40 38.1 24 1 1/2" 1 1/2" 81.0 151.5 63.5

32 50 50.8 32 2" 2" 100.0 176.0 79.4

HG3990° SAE J518 FLANGE - 6000 PSI

ONE PIECE



O8 12 12.7 08 1/2" 1/2" 41 74 42 31.7

12 20 19.1 12 3/4" 3/4" 58 99 62 41.3

16 25 25.4 16 1" 1" 74 129 75 47.6

20 32 31.8 20 1 1/4" 1 1/4" 92 153 90 54.0

24 40 38.1 24 1 1/2" 1 1/2" 108 179 102 63.5

32 50 50.8 32 2" 2" 142 218 137 79.4

HOSE CONNECTORS

FLANGE

FLANGE

SAE FLANGE 90 DEG 6000 PSI STANDARD CODE

SAE FLANGE 6000 PSI STANDARD

CODE

18


HJ3945° SAE J518 FLANGE - 6000 PSI

ONE PIECE



O8 12 12.7 08 1/2" 1/2" 63.0 96.0 23.5 31.7

12 20 19.1 12 3/4" 3/4" 89.5 130.5 36.0 41.3

16 25 25.4 16 1" 1" 112.0 167.0 44.0 47.6

20 32 31.8 20 1 1/4" 1 1/4" 138.5 200.0 55.0 54.0

24 40 38.1 24 1 1/2" 1 1/2" 162.5 233.0 58.5 63.5

12 20 19.1 12 3/4" 3/4" 89.5 130.5 36.0 41.3

32 50 50.8 32 2" 2" 212.5 289.0 73.5 79.4

HZF39SAE J518 SPLIT FLANGE HALF

6000 PSI

Dimensions(mm)

B D E F I

O8 23.8 9 9.2 15.9 22.2

12 30.2 11 11.9 19.0 28.6

16 34.9 13 13.9 22.2 36.5

20 38.9 15 15.8 23.8 39.7

24 47.6 17 18.2 27.0 46.0

32 57.1 21 22.2 36.5 55.6

HOSE CONNECTORS

C

56.3 40.5

71.4 50.8

80.9 57.1

95.2 66.7

FLANGE

SAE SPLIT FLANGE 6000 PSI

CODE

SAE FLANGE 6000 PSI 45 DEG STANDARD CODE

A

FLANGE

112.7 79.4

133.3 96.8

1/2"

3/4"

1"

1 1/4"

1 1/2"

2"

19


HA50 J.I.C. MALE - 74° CONE



O4 6 6.30 04 1/4" 7/16"-20 26.5 55.0 12.0

O5 8 7.90 05 5/16" 1/2"-20 26.5 55.0 14.0

O6 10 9.50 06 3/8" 9/16"-18 26.5 57.0 15.0

O8 12 12.70 08 1/2" 3/4"-16 28.7 61.7 19.0

10 16 15.90 10 5/8" 7/8"-14 34.7 70.7 24.0

12 20 19.10 12 3/4" 1 1/16"-12 40.4 81.4 27.0

16 25 25.40 16 1" 1 5/16"-12 42.7 97.7 36.0

20 32 31.80 20 1 1/4" 1 5/8"-12 46.5 107.5 46.0

24 40 38.10 24 1 1/2" 1 7/8"-12 51.2 121.7 50.0

32 50 50.80 32 2" 2 1/2"-12 62.2 138.2 65.0

HA53 J.I.C. FEMALE - 74° CONE



O4 6 6.3 04 1/4" 7/16"-20 14.7 43.2 15.0

O5 8 7.9 05 5/16" 1/2"-20 16.0 44.5 17.0

O6 10 9.5 06 3/8" 9/16"-18 16.0 46.5 19.0

O8 12 12.7 08 1/2" 3/4"-16 20.0 53.0 24.0

10 16 15.9 10 5/8" 7/8"-14 21.5 57.5 27.0

12 20 19.1 12 3/4" 1 1/16"-12 24.0 65.0 32.0

16 25 25.4 16 1" 1 5/16"-12 26.0 81.0 41.0

20 32 31.8 20 1 1/4" 1 5/8"-12 27.8 88.8 50.0

24 40 38.1 2'4 1 1/2" 1 7/8"-12 31.5 102.0 55.0

32 50 50.8 32 2" 2 1/2"-12 33.5 109.5 70.0

HOSE CONNECTORS

CODE

JIC MALE STANDARD

JIC FEMALE STANDARD

CODE

20


HG53 J.I.C. 90° SWEPT ELBOW - 74° CONE SEATSOLID - PRESSED NUT


DN mm SIZE Inch F H L K S

O4 6 6.3 04 1/4" 7/16"-20 24 52 24 15

O5 8 7.9 05 5/16" 1/2"-20 31 59 29 17

O6 10 9.5 06 3/8" 9/16"-18 34 64 33 19

O8 12 12.7 08 1/2" 3/4"-16 41 74 41 24

10 16 15.9 10 5/8" 7/8"-14 49 85 49 27

12 20 19.1 12 3/4" 1 1/16"-12 58 99 59 32

16 25 25.4 16 1" 1 5/16"-12 74 129 72 41

20 32 31.8 20 1 1/4" 1 5/8"-12 92 153 87 50

24 40 38.1 2'4 1 1/2" 1 7/8"-12 108 179 100 55

32 50 50.8 32 2" 2 1/2"-12 142 218 126 70

HJ53 J.I.C. 45° SWEPT ELBOW - 74° CONE SEATSOLID - PRESSED NUT


DN mm SIZE Inch F H L K S

O4 6 6.3 04 1/4" 7/16"-20 37.0 66.0 13.5 15.0

O5 8 7.9 05 5/16" 1/2"-20 46.0 74.5 16.0 17.0

O6 10 9.5 06 3/8" 9/16"-18 51.0 81.0 17.0 19.0

O8 12 12.7 08 1/2" 3/4"-16 62.0 98.0 22.5 24.0

10 16 15.9 10 5/8" 7/8"-14 77.0 113.0 25.0 27.0

12 20 19.1 12 3/4" 1 1/16"-12 86.0 127.0 33.0 32.0

16 25 25.4 16 1" 1 5/16"-12 107.5 162.5 40.0 41.0

20 32 31.8 20 1 1/4" 1 5/8"-12 135.5 196.5 52.0 50.0

24 40 38.1 24 1 1/2" 1 7/8"-12 161.0 231.0 57.0 55.0

32 50 50.8 32 2" 2 1/2"-12 205.5 281.0 66.5 70.0

HOSE CONNECTORS

CODE

CODE

JIC FEMALE 90 DEG STANDARD

JIC FEMALE 45 DEG

21


HA65METRIC MALE - 24° CONE SEAT

LIGHT TYPE


DN mm SIZE Inch F H L E S

O4 6 6.30 04 1/4" M12x1,5 23 52 6 14

O4 6 6.30 04 1/4" M14x1,5 23 52 8 14

O5 8 7.90 05 5/16" M16x1,5 24 53 10 17

O6 10 9.50 06 3/8" M16x1,5 24 55 10 17

O6 10 9.50 06 3/8" M18x1,5 24 55 12 19

O8 12 12.70 08 1/2" M22x1,5 29 62 15 24

10 16 15.90 10 5/8" M26x1,5 29 65 18 27

12 20 19.10 12 3/4" M30x2 32 73 22 32

16 25 25.40 16 1" M36x2 33 88 28 36

20 32 31.80 20 1 1/4" M45x2 38 99 35 46

24 40 38.10 24 1 1/2" M52x2 41 111 42 55

HA68METRIC MALE - 24° CONE SEAT

HEAVY TYPE


DN mm SIZE Inch F H L E S

O4 6 6.3 04 1/4" M16x1,5 25 54 8 17

O4 6 6.3 04 1/4" M18x1,5 26 55 10 19

O6 10 9.5 06 3/8" M20x1,5 27 58 12 22

O6 10 9.5 06 3/8" M22X1,5 29 60 14 24

O8 12 12.7 08 1/2" M24x1,5 31 64 16 27

10 16 15.9 10 5/8" M30x2 33 69 20 32

12 20 19.1 12 3/4" M36x2 36 77 25 36

16 25 25.4 16 1" M42x2 41 96 30 46

20 32 31.8 20 1 1/4" M52x2 46 107 38 55

HOSE CONNECTORS

CODE

CODE

METRIC MALE (LIGHT)STANDARD

METRIC MALE (HEAVY)

STANDARD

22


HA67O'RING METRIC FEMALE - 24° CONE

LOOSE NUT - LIGHT TYPE

Hose I.D. Thread Tube Dimensions(mm)

DN mm SIZE Inch F mm H L S

O4 6 6.3 04 1/4" M12x1,5 6 23 52 17

O4 6 6.3 04 1/4" M14x1,5 8 24 53 17

O5 8 7.9 05 5/16" M16x1,5 10 25 54 19

O6 10 9.5 06 3/8" M16x1,5 10 25 56 19

O6 10 9.5 06 3/8" M18x1,5 12 25 56 22

O8 12 12.7 08 1/2" M22x1,5 15 27 60 27

10 16 15.9 10 5/8" M26x1,5 18 28 64 32

12 20 19.1 12 3/4" M30x2 22 31 72 36

16 25 25.4 16 1" M36x2 28 33 88 41

20 32 31.8 20 1 1/4" M45x2 35 37 98 50

24 40 38.1 24 1 1/2" M52x2 42 39 109 60

HA69O'RING METRIC FEMALE -24° CONE

LOOSE NUT - HEAVY TYPE


DN mm SIZE Inch F mm H L S

O4 6 6.3 04 1/4" M16x1,5 8 24 53 19

O4 6 6.3 04 1/4" M18x1,5 10 25 54 22

O6 10 9.5 06 3/8" M20x1,5 12 25 56 24

O6 10 9.5 06 3/8" M22x1,5 14 29 60 27

O8 12 12.7 08 1/2" M24x1,5 16 31 64 30

10 16 15.9 10 5/8" M30x2 20 35 71 36

12 20 19.1 12 3/4" M36x2 25 39 80 46

16 25 25.4 16 1" M42x2 30 41 96 50

20 32 31.8 20 1 1/4" M52x2 38 47 108 60

HOSE CONNECTORS

CODE

CODE

METRIC FEMALE (LIGHT) STANDARD

METRIC FEMALE (HEAVY) STANDARD

23


HG67 90° O-RING METRIC SWEPT ELBOW - 24° CONESOLID - LOOSE NUT - LIGHT TYPE


DN mm SIZE Inch F mm H L K S

4 6 6.3 04 1/4" M12x1,5 6 24 52 28 17

4 6 6.3 04 1/4" M14x1,5 8 24 52 28 17

6 10 9.5 06 3/8" M16x1,5 10 34 64 36 19

6 10 9.5 06 3/8" M18x1,5 12 34 64 35 22

8 12 12.7 08 1/2" M22x1,5 15 41 74 41 27

10 16 15.9 10 5/8" M26x1,5 18 49 85 49 32

12 20 19.1 12 3/4" M30x2 22 58 99 54 36

16 25 25.4 16 1" M36x2 28 74 129 68 41

20 32 31.8 20 1 1/4" M45x2 35 92 153 86 50

24 40 38.1 24 1 1/2" M52x2 42 108 179 96 60

HG69 90° O-RING METRIC SWEPT ELBOW - 24° CONESOLID - LOOSE NUT - HEAVY TYPE



O4 6 6.3 04 1/4" M16x1,5 8 24 52 28 19

O4 6 6.3 04 1/4" M18x1,5 10 24 52 30 22

O6 10 9.5 06 3/8" M20x1,5 12 34 64 35 24

O6 10 9.5 06 3/8" M22x1,5 14 34 64 37 27

O8 12 12.7 08 1/2" M24x1,5 16 41 74 42 30

10 16 15.9 10 5/8" M30x2 20 49 85 53 36

12 20 19.1 12 3/4" M36x2 25 58 99 59 41

16 25 25.4 16 1" M42x2 30 74 129 71 50

20 32 31.8 20 1 1/4" M52x2 38 92 153 86 60

HOSE CONNECTORS

CODE

CODE

METRIC FEMALE 90 DEG (LIGHT)STANDARD

METRIC FEMALE 90 DEG (HEAVY)STANDARD

24

HOSE CONNECTORS

HJ6745° O-RING METRIC SWEPT ELBOW - 24° CONE

SOLID - LOOSE NUT - LIGHT TYPE



O4 6 6.3 04 1/4" M12x1,5 6 43.0 71.5 19.0 17

O4 6 6.3 04 1/4" M14x1,5 8 39.5 68.0 16.0 17

O6 10 9.5 06 3/8" M16x1,5 10 58.0 88.0 23.5 19

O6 10 9.5 06 3/8" M18x1,5 12 53.0 83.5 19.0 22

O8 12 12.7 08 1/2" M22x1,5 15 62.0 95.0 22.5 27

10 16 15.9 10 5/8" M26x1,5 18 79.0 115.0 26.0 32

12 20 19.1 12 3/4" M30x2 22 87.0 127.5 31.0 36

16 25 25.4 16 1" M36x2 28 109.0 164.0 40.0 41

20 32 31.8 20 1 1/4" M45x2 35 137.5 198.5 53.0 50

24 40 38.1 24 1 1/2" M52x2 42 161.5 231.5 56.5 60

HJ6945° O-RING METRIC SWEPT ELBOW - 24° CONE

SOLID - LOOSE NUT - HEAVY TYPE



O4 6 6.3 04 1/4" M16x1,5 8 39.5 68.0 16.0 19.0

O4 6 6.3 04 1/4" M18x1,5 10 40.5 69.0 16.5 22.0

O6 10 9.5 06 3/8" M20x1,5 12 53.0 83.5 19.0 24.0

O6 10 9.5 06 3/8" M22x1,5 14 54.5 85.0 20.5 27.0

O8 12 12.7 08 1/2" M24x1,5 16 63.5 96.5 24.0 30.0

10 16 15.9 10 5/8" M30x2 20 81.5 117.5 28.0 36.0

12 20 19.1 12 3/4" M36x2 25 90.0 131.0 35.5 41.0

16 25 25.4 16 1" M42x2 30 110.0 165.0 41.5 50.0

20 32 31.8 20 1 1/4" M52x2 38 139.0 200.0 54.0 60.0

HOSE CONNECTORS

METRIC FEMALE (LIGHT ) 45 DEG

STANDARD TIEFFEPart. N°

METRIC FEMALE (HEAVY) 45 DEG

STANDARD CODE

25

2001


HA76 "KOMATSU" METRIC FEMALE - 60º CONE SEATPRESSED NUT

Hose I.D. Thread

DN mm SIZE Inch F

O4 6 6.3 04 1/4" M14x1,5

O6 10 9.5 06 3/8" M18x1,5

O8 12 12.7 08 1/2" M22X1,5

10 16 15.9 10 5/8" M24x1,5

12 20 19.1 12 3/4" M30x1,5

16 25 25.4 16 1" M33x15

20 32 31.8 20 1 1/4" M36x1,5

24 40 38.1 24 1 1/2" M42x1,5

HA83WASHCLEANER FEMALE

"FK" TYPE


DN mm SIZE Inch F H L D

O4 6 6.3 04 1/4" M22x1,5 31 59.5 14

O5 8 7.9 05 5/16" M22x1,5 31 59.5 14

O6 10 9.5 06 3/8" M22x1,5 31 61.5 14

HA92B.S.P. BANJO

SOLID

Hose I.D. BoltDimensions

(mm)

DN mm SIZE Inch Thread H L D S

O4 6 6.3 04 1/4" 1/4"-19 24.5 65.0 13.3 14.0

O6 10 9.5 06 3/8" 3/8"-19 26.5 71.0 16.9 17.0

O8 12 12.7 08 1/2" 1/2"-14 31.0 82.0 21.0 23.5

10 16 15.9 10 5/8" 5/8"-14 32.5 88.5 23.3 25.0

12 20 19.1 12 3/4" 3/4"-14 37.5 101.0 26.5 30.0

16 25 25.4 16 1" 1"-11 50.5 134.5 33.5 38.0

HOSE CONNECTORS

CODE

CODE

KOMATSU FEMALE STANDARD

K ARCHER FEMALE STANDARD

BSP BANJOCODE

26

D


HA93 METRIC BANJO - ONE PIECE

Hose I.D. BoltDimensions

(mm)

DN mm SIZE Inch Thread H L D S

O4 6 6.3 04 1/4" M14x1,5 24.5 65.0 14.1 14.0

O6 10 9.5 06 3/8" M16x1,5 25.5 71.0 16.1 16.0

O8 12 12.7 08 1/2" M18x1,5 31.5 80.5 18.1 20.0

10 16 15.9 10 5/8" M22x1,5 34.0 88.0 22.1 23.5

12 20 19.1 12 3/4" M30x1,5 43.5 111.5 30.1 36.0

HA96 DOUBLE INSERT


DN mm SIZE Inch H L

O4 6 6.3 04 1/4" 13 70

O5 8 7.9 05 5/16" 13 70

O6 10 9.5 06 3/8" 13 74

O8 12 12.7 08 1/2" 15 81

10 16 15.9 10 5/8" 15 87

12 20 19.1 12 3/4" 17 99

16 25 25.4 16 1" 20 130

HOSE CONNECTORS

CODE

CODE

METRIC BANJO

DOUBLE INSERT

27

D

ADAPTORS 2001

ADAPTORS

JIC MALE XJIC MALE

BSP MALE XBSP FEMALE

BSP FEMALE X BSP FEMALE

BSP BULKHEAD BSP LOCKNUT BSP BLANKING PLUG

BSP MALE / MALE 90ºELBOW

BSP MALE / FEMALE 90ºCOMPACT ELBOW

JIC MALE X NPTFMALE 90º ELBOW

JIC MALE XSAE 'O' RINGBOSS MALE

BSP MALE XSAE 'O' RINGBOSS MALE

BSP MALE X FEMALEREDUCING BUSH

BSP MALE XMETRIC MALE

BSP MALE X JIC FEMALE

JIC BLANKING PLUG BSP EQUAL FEMALE 'T' JIC MALE X SAE'O'RINGBOSS ADJUSTER 90º

JIC MALE XJIC FEMALE 90º

BSP TEE MALE/MALE MALE EQUAL

JIC MALE XMALE X FEMALE TEE

BSP BLANKING CAP METRIC MALE X MALE JIC MALE BULKHEADWITH LOCKNUT

BSP TEE MALE X MALEX FEMALE

BSP TEE MALE XFEMALE / MALE

BSP MALE X FEMALE45º SWEPT ELBOW

BSP MALE / FEMALE90º SWEPT ELBOW

BANJO BOLT METRIC PLUG METRIC CAP

28

BSP MALE XBSP MALEEQUAL

BSP MALE XBSP MALEUNEQUAL

BSP MALE XBSP TAPERMALE

BSP MALE XNPTF MALE

BSP MALE XJIC MALE

JIC MALE XNPTF MALE

STEEL TUBING 2001

HWMTSEAMLESS STEEL TUBES DIN 2391 MATERIAL ST

37.4 NBK

THICKNESS STATIC DYNAMIC BURST KG/MTR

MM W/P BAR W/P BAR PRE. BAR APPROX

4 0.75 409 393 1,820 0.063

5 1 432 416 2,120 0.099

6 1 389 374 1,680 0.123

6 1.5 549 528 3,050 0.166

6 1 333 289 1,190 0.173

8 1.5 431 414 1,860 0.24

10 1 282 249 870 0.222

10 1.5 373 358 1,380 0.314

12 1.5 353 305 1,150 0.388

12 2 409 393 1,580 0.493

14 1.5 302 265 940 0.462

15 1.5 282 249 980 0.499

15 2 376 323 1,250 0.641

16 2 353 305 1,170 0.691

18 1.5 235 210 780 0.61

18 2 313 274 1,040 0.789

20 1.5 212 191 570 0.684

20 2 282 249 920 0.888

20 2.5 353 305 1,220 1.079

22 2 256 228 850 0.986

22 2.5 320 280 1,040 1.202

25 2.5 282 249 920 1.387

25 3 338 294 1,050 1.628

28 2 201 182 620 1.282

28 2.5 252 224 770 1.572

28 3 302 265 920 1.85

30 3 282 249 920 1.998

35 2.5 201 182 620 2.004

35 3 242 216 720 2.367

38 2.5 186 168 550 2.189

38 4 297 261 970 3.354

42 3 201 182 580 2.885

STEEL TUBING

OD

Steel Tubes DIN 2391

29

Accessories 2001

H4000

SIZE ININCHES

MM INCHES

BSP NPT

2 1/8 1/8

4 1/4 1/4

6 3/8 3/8

8 1/2 1/2

12 3/4 3/4

16 1 1

10

12

15

19

21

23

26

31 31

33 33

37 37

40 40

41 41

47 47

52 52

CODE

HZP

CODE

QUICK RELEASE COUPLINGS

SPRING GUARDSSIZE IN

MM

ID

10

12

15

19

21

23

26

ID IDCODE CODE

10

BONDEDBONDED

10

12 12

14 14

16 16

18 18

20 20

22 22

24 24

26 26

28 28

30 30

36 36

2

4

6

8

10

12

16

20

24

32

1/8

1/4

3/8

1/2

5/8

3/4

1

1 1/4

1 1/2

2

DOWTY SEALS - METRIC

DOWTY SEALS - INCH SIZES

HZS01HZS05

30Accessories

Other Products

Other Products

2001

Other Products RangeAircondition and Refrigeration Hoses

Steel Braided fuel hoses

Oil Suction/Delivery hoses

Water Suction/Delivery hoses

Air Hoses

Radiator hoses

PVC reinforced hoses

Cement hoses

Oxygen/Acetylene hoses

Nylon Tubing

Copper Tubing

Reusable fittings in different threads and sizes

Eremeto Fittings

Brass Compression fittings

Brass Adaptors

Brass Low pressure fittings

Stainless Steel compression fittings

Camlock Coupling, King Nipples etc.

Bolt clamps, Steel clips

Tube clamps

Brass Air Coupler

Plastic Connectors

Ball Valves and Gate Valves

"O" Rings, Copper washers etc.

31

Technical Information 2001

32Technical Information

2001

33

Technical Information


2001

1 KP

a =

0.14

5 PS

I = 1

/100

BAR

= 0

.010

19KG

/SQ

CM

EXAM

PLE

:- 21

.1 K

G/S

Q C

M =

300

PSI

= 2

0.6

BAR

S =

2060

KPa

= 2

.06

Mpa

kg/sq

cmp.

s.Iba

rskg

/sq cm

p.s.I

bars

kg/sq

cmp.

s.Iba

rskg

/sq cm

p.s.I

bars

kg/sq

cmp.

s.Iba

rs21

.130

020

.69

161.

7423

0015

8.62

302.

3943

0029

6.55

443.

0463

0043

4.48

583.

6883

0057

2.41

24.6

350

24.1

416

5.26

2350

162.

0730

5.91

4350

300.

0044

6.55

6350

437.

9358

7.20

8350

575.

8628

.140

027

.59

168.

7824

0016

5.52

309.

4244

0030

3.45

450.

0764

0044

1.38

590.

7284

0057

9.31

31.6

450

31.0

317

2.29

2450

168.

9731

2.94

4450

306.

9045

3.59

6450

444.

8359

4.23

8450

582.

7635

.250

034

.48

175.

8125

0017

2.41

316.

4645

0031

0.34

457.

1065

0044

8.28

597.

7585

0058

6.21

38.7

550

37.9

317

9.32

2550

175.

8631

9.97

4550

313.

7946

0.62

6550

451.

7260

1.27

8550

589.

6642

.260

041

.38

182.

8426

0017

9.31

323.

4946

0031

7.24

464.

1466

0045

5.17

604.

7886

0059

3.10

45.7

650

44.8

318

6.36

2650

182.

7632

7.00

4650

320.

6946

7.65

6650

458.

6260

8.30

8650

596.

5549

.270

048

.28

189.

8727

0018

6.21

330.

5247

0032

4.14

471.

1767

0046

2.07

611.

8187

0060

0.00

52.7

750

51.7

219

3.39

2750

189.

6633

4.04

4750

327.

5947

4.68

6750

465.

5261

5.33

8750

603.

4556

.380

055

.17

196.

9128

0019

3.10

337.

5548

0033

1.03

478.

2068

0046

8.97

618.

8588

0060

6.90

59.8

850

58.6

220

0.42

2850

196.

5534

1.07

4850

334.

4848

1.72

6850

472.

4162

2.36

8850

610.

3463

.390

062

.07

203.

9429

0020

0.00

344.

5949

0033

7.93

485.

2369

0047

5.86

625.

8889

0061

3.79

66.8

950

65.5

220

7.45

2950

203.

4534

8.10

4950

341.

3848

8.75

6950

479.

3162

9.40

8950

617.

2470

.310

0068

.97

210.

9730

0020

6.90

351.

6250

0034

4.83

492.

2670

0048

2.76

632.

9190

0062

0.69

73.8

1050

72.4

121

4.49

3050

210.

3435

5.13

5050

348.

2849

5.78

7050

486.

2163

6.43

9050

624.

1477

.311

0075

.86

218.

0031

0021

3.79

358.

6551

0035

1.72

499.

3071

0048

9.66

639.

9491

0062

7.59

80.9

1150

79.3

122

1.52

3150

217.

2436

2.17

5150

355.

1750

2.81

7150

493.

1064

3.46

9150

631.

0384

.412

0082

.76

225.

0432

0022

0.69

365.

6852

0035

8.62

506.

3372

0049

6.55

646.

9892

0063

4.48

87.9

1250

86.2

122

8.55

3250

224.

1436

9.20

5250

362.

0750

9.85

7250

500.

0065

0.49

9250

637.

9391

.413

0089

.66

232.

0733

0022

7.59

372.

7153

0036

5.52

513.

3673

0050

3.45

654.

0193

0064

1.38

94.9

1350

93.1

023

5.58

3350

231.

0337

6.23

5350

368.

9751

6.88

7350

506.

9065

7.52

9350

644.

8398

.414

0096

.55

239.

1034

0023

4.48

379.

7554

0037

2.41

520.

3974

0051

0.34

661.

0494

0064

8.28

102

1450

100.

0024

2.62

3450

237.

9338

3.26

5450

375.

8652

3.91

7450

513.

7966

4.56

9450

651.

7210

5.5

1500

103.

4524

6.13

3500

241.

3838

6.78

5500

379.

3152

7.43

7500

517.

2466

8.07

9500

655.

1710

915

5010

6.90

249.

6535

5024

4.83

390.

3055

5038

2.76

530.

9475

5052

0.69

671.

5995

5065

8.62

112.

516

0011

0.34

253.

1636

0024

8.28

393.

8156

0038

6.21

534.

4676

0052

4.14

675.

1196

0066

2.07

116

1650

113.

7925

6.68

3650

251.

7239

7.33

5650

389.

6653

7.97

7650

527.

5967

8.62

9650

665.

5211

9.5

1700

117.

2426

0.20

3700

255.

1740

0.84

5700

393.

1054

1.49

7700

531.

0368

2.14

9700

668.

9712

3.1

1750

120.

6926

3.71

3750

258.

6240

4.36

5750

396.

5554

5.01

7750

534.

4868

5.65

9750

672.

4112

6.6

1800

124.

1426

7.23

3800

262.

0740

7.88

5800

400.

0054

8.52

7800

537.

9368

9.17

9800

675.

8613

0.1

1850

127.

5927

0.75

3850

265.

5241

1.39

5850

403.

4555

2.04

7850

541.

3869

2.69

9850

679.

3113

3.6

1900

131.

0327

4.26

3900

268.

9741

4.91

5900

406.

9055

5.56

7900

544.

8369

6.20

9900

682.

7613

7.1

1950

134.

4827

7.78

3950

272.

4141

8.42

5950

410.

3455

9.07

7950

548.

2869

9.72

9950

686.

2114

0.6

2000

137.

9328

1.29

4000

275.

8642

1.94

6000

413.

7956

2.59

8000

551.

7270

3.23

1000

068

9.66

144.

120

5014

1.38

284.

8140

5027

9.31

425.

4660

5041

7.24

566.

1080

5055

5.17

706.

7510

050

693.

1014

7.7

2100

144.

8328

8.33

4100

282.

7642

8.97

6100

420.

6956

9.62

8100

558.

6271

0.27

1010

069

6.55

151.

221

5014

8.28

291.

8441

5028

6.21

432.

4961

5042

4.14

573.

1481

5056

2.07

713.

7810

150

700.

0015

4.7

2200

151.

7229

5.36

4200

289.

6643

6.01

6200

427.

5957

6.65

8200

565.

5271

7.30

1020

070

3.45

158.

222

5015

5.17

298.

8742

5029

3.10

439.

5262

5043

1.03

580.

1782

5056

8.97

720.

8210

250

706.

90

PRES

SUR

E C

ON

VER

SIO

N C

HA

RT

34

1 ps

i = 0

.068

96 B

AR =

6.8

966

KPa

= 0.

0703

KG

/SQ

CM

1 BA

R =

14.

5 PS

I = 1

00 K

Pa =

1/1

0 M

Pa =

1.0

19 K

G/S

Q C

M1

KG/S

Q C

M =

14.

22 P

SI =

98.

1 KP

a =

.981

BAR

1 M

Pa =

145

PSI

= 1

0 BA

R =

10.

19 K

G/S

Q C

M



2001

35



2001

36



Trinity Mechanical Services LLC(Hydraulic Division)

P.O.Box 8807, Dubai - UAE, Tel: 04 2853342, Fax: 04 2853347Email: [email protected], www.trinityholdings.com

Assembly and Supply of:• Hydraulic Hoses and Fittings • Stainless steel corrugated hoses and fittings • Stainless steel expansion bellows • Steel tubes, tube fittings & tube clamps • Suction / Discharge, Air & Chemical hoses etc. • Pressure gauges, dowty seals, ball valves, quick release couplings etc

Documents

Trinity Hydraulics - Catalog