The AVT Composite Valve Range - Shipham Valves€¦ · Others by request Notes 1) Max WP for AVT 530 material, non-dangerous fluids at ambient temperature. AVT 520 is 80% of listed

The World’s Preferred Partner for CorrosionResistant Valve Solutions

Offshore Oil & Gas

Naval Marine

Desalination

Marine Services

Chemical

Waste Water Treatment

The AVT Composite Valve Range

shipham-valves.com

AVT brochure amends_Layout 1 20/11/2012 09:53 Page 1

shipham-valves.com

The World’s Preferred Partner for CorrosionResistant Valve SolutionsShipham Valves is one of the longest established and most highly respected valve manufacturers in the

world, with a global reputation for excellence in product design, quality, reliability and the highest levels of

customer service.

Since the 1930s, Shipham Valves has been a key manufacturer of valves for the global naval defence industries. In a market known for its arduous demands for productperformance and reliability, quality assurance, traceability, certification and documentation, we have built an unrivalled reputation for excellence.

We have successfully taken our experience and capabilities into many other areas, including the oil & gas and petrochemical markets. Shipham Valves is now firmlyestablished as a global leader in the design and manufacture of high alloy valve products used in severe service applications handling sea water and other corrosive media.

Shipham’s leadership in the manufacture of valves for corrosive applications was further enhanced in 2008 with the acquisition of Advanced Valve Technologies (AVT).

The AVT Composite range comprises ball, butterfly and wafer check valves manufactured using reinforced composite technology which offers outstanding internal & external corrosion resistance and significant weight savings over equivalent metallic valves.


Reinforced Composite Technology appliedto fluid handling and controlKey benefits of reinforced composites:

Outstanding internal and external corrosion resistance

- eliminating the need for external coatings and protective linings

Up to 60% weight saving

- leading to a very significant reduction of handling, installation and delivery costs

Very low thermal conductivity

- eliminating the need for lagging leading to further cost savings

Reduced torque

- leading to lower costs of actuation

Total lifecycle

- cost savings against metallic valves can be up to 90%

Reliable, short leadtimes

- eliminating project over-runs


shipham-valves.com

Butterfly Valves - Corrosion resistant, highperformance, firesafe API 607 (optional)Double offset seat design and 360° bubble tight

sealing and low operating torque with extended

seat life and up to 60% weight saving versus

metal valves!

Operator Design

Corrosion resistant lightweight, lockable levers with 7 intermediate stops are

standard. Mounting accommodates ISO Standard gear operators and actuators.

Corrosion resistant stem extensions for buried service made to customer

requirements.

Full Flange Face Body

For reduced flange cost, AVT valves do not require the use of heavy duty flanges

when used with GRE pipe systems. They can be used as direct replacements for

metal butterfly valves of a similar specification.

Available with plain holes (for through bolting) or with tapped inserts.

Disc / Seat Design

This disc design takes advantage of the inherent strength of all the resin systems to

limit the overall thickness of the disc, thereby reducing the restriction of flow to a

practical minimum when the valve is fully opened.

The seat is secured to the disc by a moulded retaining plate. Leakage behind the

seat is prevented by a secondary seal moulded on the inside diameter of the seat.

Shaft Assembly

Our unique shaft/disc connection eliminates flutter for improved flow and noise

reduction. Shaft designed as non-wetted, blow out proof.

First Degree Off-Set

The off-set between the seat face and the shaft axis makes the 360° seat

possible ensuring bubble tight sealing even in high cycling applications.

Shafts

Sealed with a multi “O” ring system that ensures long life tight sealing even in high

cycling applications without need for maintenance. Hastelloy® non wetted shaft as

standard, with 316 and Titanium optional.

Second Degree Off-Set

The off-set of the shaft with respect to the axis of the bore combined with the first

degree of off-set ensures that the sector of the seat sealing face is effectively cleared

from contact by a very small angular motion.

The introduction of this second degree of off-set reduces wear and break out

torque.


Others by request

Notes 1) Max WP for AVT 530 material, non-dangerous fluids at ambient temperature. AVT 520 is 80% of listed pressures. For other temperatures & fluids, please referto Shipham Valves. 2) To allow for variations in break torque due to pressure and viscosity variations, it is recommended that actuators capable of developing forces aminimum of 30% greater than the above are used. Higher safety factors may be required in some applications e.g. when operations are infrequent.

Note: Specifications are subject to alteration.

Options

Body and Disc Material

Please contact Shipham Valvesfor material compatibility

Subject to media

Max Long Term Temperature

Flange Configurations

Sizes

Shaft Option 316 SS, Titanium Grade 5, Hastelloy®, Monel®, Duplex, Super Duplex

Elastomer Options EDPM, Viton A, Viton B, Nitrile NBR

3” (80mm) – 12” (300mm)

AVT530

Composite Epoxy Filled Resin System

110°C / 230°F

ANSI 150, DIN, BS, ISO Available drilled through or tapped

AVT520

Composite ProprietaryNovolac Filled Resin System

120°C / 250°F

Dimensions for ANSI 150 Butterfly Valves

Valve Size Weight CV Torque 2) Torque 2) Torque 2) Max WP1)

A B C D E F lbs US g/m inch-lb@0psi inch-lb@70psi inch-lb@145psi psi

3 1.88 4.3 8.31 12.6 3 8.3 8.42 278 60 120 168 235

4 2.12 4.9 9.06 12.6 4 9.1 10.63 485 120 264 576 205

6 2.25 6.3 10.63 12.6 6 12.2 20.72 1267 144 576 1200 145

8 2.50 7.6 12.56 24.1 8 15.0 32.63 2174 180 708 1488 100

10 2.81 8.9 N/A N/A 10 17.5 46.30 3457 191 836 1761 75

12 3.19 10.6 N/A N/A 12 20.5 72.75 4971 221 1150 2389 75

IMPERIAL DIMENSIONS (inch / lbs)

Dimensions for ANSI 150 Butterfly Valves

Valve Size Weight CV Torque 2) Torque 2) Torque 2) Max WP1)

A B C D E F Kg US g/m Nm@0bar Nm@5bar Nm@10bar Bar

80 47.8 110 211 320 84 210 3.82 278 6.5 13.5 18.9 16.0

100 53.8 125 230 320 110 232 4.82 485 13.5 29.7 64.8 14.0

150 57.1 160 270 320 160 310 9.40 1267 16.2 64.8 135 10.0

200 63.5 192 319 613 198.8 381 14.80 2174 20.25 79.65 167.4 7.0

250 71.4 225 N/A N/A 260 445 21.00 3457 21 94 199 5.0

300 81.0 270 N/A N/A 306 520 33.00 4971 25 130 270 5.0

METRIC DIMENSIONS (mm / kg)

mm

inch


shipham-valves.com

Ball Valves - Corrosion resistant, firesafe(optional) regular (reduced) port ball valvesOperator Design

Corrosion resistant, lightweight, lockable levers are standard. Gearboxes can be

fitted onto the valve.

Actuation

Any standard actuator can be fitted including ancillary equipment such as switch

boxes, solenoids, beacon indicators, etc.

Standard Mounting Pad

ISO mounting for actuation.

Gland Packing

Energised chevron is standard. (‘O’ ring seal can be supplied if required).

Stem

Blow-out proof design.

Materials available: Hastelloy®, Duplex, Super Duplex, Titanium,

Stainless Steel, etc.

Seating System

Bubble tight sealing. Available in Super PTFE TFM or Virgin PTFE seats. Options

include glass filled PTFE, carbon filled PTFE or PEEK.

Regular (Reduced) Port

Optimum flow rate in a compact, economical

one-piece design.

Firesafe Option

AVT ball valves are available in a firesafe option with an intumescent paint coating.

Gland Packing

PTFE chevron packing combination stem sealing system with energiser.

A parallel “O” ring backup. A parallel motion adjuster applies even pressure

on the chevron pack for simpler and quicker adjustment.

Chevron Stuffing Box System


316 SS, Titanium Grade 5, Hastelloy®,Monel®, Duplex, Super Duplex

TFM, Viton A, Viton B, EPDM, Nitrile NBR


Options

Shaft Option

ElastomerOptions

Seat

Notes 1) Max WP for AVT 530 material, non-dangerous fluids at ambient temperature. AVT 520 is 80% of listed pressures. For other temperatures & fluids, please referto Shipham Valves 2) To allow for variations in break torque due to pressure and viscosity variations, it is recommended that actuators capable of developing forces aminimum of 30% greater than the above are used. Higher safety factors may be required in some applications e.g. when operations are infrequent.Ball Valve BreakTorques are for valves with Chevron Stuffing Box System. 3) DN 200 / 8” Reduced Bore Ball Valve is also available as 3-piece design (Long Pattern).

Dimensions for ANSI 150 Regular Port (Reduced Bore) Ball Valves - 1 Piece Design


Dimensions for ANSI 150 Regular Port (Reduced Bore) Ball Valves - 1 Piece Design


Valve Size Weight Torque 2) Torque 2) Torque 2) Max WP 1)

inch A B C D H1 H2 J lbs inch-lb@0bar inch-lb@70psi inch-lb@145psi psi

1 5 4.41 3.5 N/A 1 3/4 2.2 3.5 75 84 97 2301 1/2 6 1/2 5.75 4.3 N/A 1 1/2 1 2.9 7.7 75 84 97 230

2 7 6.34 4.2 8.8 2 1 1/2 3.2 10.1 79 97 168 2303 8 7.87 5.0 8.8 3 2 3.9 17.6 88 132 221 2304 9 9.06 6.0 12.6 4 3 4.5 24.3 97 318 743 2305 10 10 7.7 12.6 5 4 5.0 39.7 106 584 1002 2306 10 1/2 11.1 19.9 6 4 5.6 48.5 106 584 1002 2308 11 1/2 13.5 24.1 8 6 6.8 70.5 1003 1422 2114 1758 3) 18 13.5 24.1 8 6 6.8 117.9 1003 1422 2114 145

Others by request

TFM

Please refer to

ShiphamValves

Body and Ball Material


Subject to media



Sizes 1” (25mm) – 8” (200mm) Reduced Port

AVT530

Composite Epoxy FilledResin System

110°C / 230°F

ANSI 150, DIN, BS, ISO

AVT520

Composite Proprietary NovolacFilled Resin System

120°C / 250°F

Valve Size Weight Torque 2) Torque 2) Torque 2) Max WP 1)

mm A B C D H1 H2 J Kg Nm@0bar Nm@5bar Nm@10bar Bar

25 127 112 89 N/A 25 19 56.0 1.6 8.5 9.5 11 1640 165 146 109 N/A 38 25 73.0 3.5 8.5 9.5 11 1650 178 161 107 222.3 51 38 80.5 4.6 9 11 19 1680 203 200 127 222.3 76 50 100.0 8.0 10 15 25 16

100 229 230 152 320.8 102 76 115.0 11.0 11 36 84 16125 254 253 195 320.8 127 100 126.5 18 12 66 120 16150 267 282 505.0 152 100 141.0 22.0 12 66 120 16200 292 345 612.9 203 152 172.5 32.0 113 160 238 12200 3) 457.2 343 612.9 203 152 171.5 53.5 113 160 238 10

Please refer to

ShiphamValves


shipham-valves.com

Ball Valves - Corrosion resistant, firesafe (optional) full port ball valvesOperator Design

Corrosion resistant, lightweight, lockable levers are offered for all Ball Valves up to

150mm (6 inch). Standard gearboxes can be fitted onto the valve.

Actuation

Any standard actuator can be fitted including ancillary equipment such as switch

boxes, solenoids, beacon indicators, etc.

Standard Mounting Pad

ISO mounting for actuation.

Gland Packing

Energised chevron.

‘O’ ring seal.

Stem

Blow-out proof design.

Materials available: Hastelloy®, Duplex, Super Duplex, Titanium, Stainless Steel, etc.

Seating System

Bubble tight sealing. Available in Super PTFE TFM or Virgin PTFE seats. Options

include glass filled PTFE, carbon filled PTFE or PEEK.

Full Port

For maximum flow rate.

Firesafe Option

AVT ball valves are available in a firesafe option with an intumescentpaint coating.

Multi Viton “O” ring shaft seals for multi-cycle maintenancefree use and low operating torque.

“O” ring system Chevron Stuffing Box System

PTFE chevron packing combination stem sealing systemwith energiser. A parallel “O” ring backup. A parallel motion adjuster applies even pressure on thechevron pack for simpler and quicker adjustment.

Design Features: AVT offer two gland packing options:


Others by request


ANSI 150, DIN, BS, ISO

Notes 1) Max WP for AVT 530 material, non-dangerous fluids at ambient temperature. AVT 520 is 80% of listed pressures.For other temperatures & fluids, please refer toShipham Valves 2) To allow for variations in break torque due to pressure and viscosity variations, it is recommended that actuators capable of developing forces a minimum of30% greater than the above are used. Higher safety factors may be required in some applications e.g. when operations are infrequent. Ball Valve Break Torques are for valveswith Chevron Stuffing Box System. 3) DN25 / 1” FB Ball Valve is a one piece, top entry design. 4) DN200 / 8” 3-Piece Design Ball Valve is Reduced Bore (Regular Port) design.

Dimensions for ANSI 150 Full Bore Ball Valves (Full Port) - 3 Piece Design

Valve Size Weight CV Torque 2) Torque 2) Torque 2) Max WP 1)

mm A B C D H I J Kg US g/m Nm@0bar Nm@5bar Nm@10bar Bar

25 3) 127 130 117 65 25 N/A 65 2.20 100 8.5 9.5 11 10.0

40 167 161 135.1 197.8 40 160 80.5 4.30 250 9 11 19 10.0

50 181 158.2 150 197.8 50 190 95 5.80 430 10 15 25 10.0

80 204 216 202 350 80 238 119 10.32 1020 11 36 84 10.0

100 232 260 230 350 100 300 150 18.18 1890 12 66 120 10.0

150 394 343 323 400 152.4 410 206 44.00 5500 113 160 238 10.0

200 4) 457 343 323 400 203 x 152.4 410 206 53.48 1800 113 160 238 10.0


Dimensions for ANSI 150 Full Bore Ball Valves (Full Port) - 3 Piece Design

Valve Size Weight CV Torque 2) Torque 2) Torque 2) Max WP 1)

inch A B C D H I J lbs US g/m inch-lb@0psi inch-lb@70psi inch-lb@145psi psi

1 3) 5 5.12 4.61 2.56 1 N/A 2.56 4.85 100 75 84 97 145

1.5 6.5 6.34 5.32 7.79 1.5 6.30 3.17 9.48 250 79 97 168 145

2 7 6.23 5.91 7.79 2 7.48 3.74 12.79 430 88 132 221 145

3 8 8.50 7.95 13.78 3 9.37 4.69 22.75 1020 97 318 743 145

4 9 10.24 9.06 13.78 4 11.81 5.91 40.08 1890 106 584 1002 145

6 15.5 13.50 12.72 15.75 6 16.14 8.11 97.00 5500 1003 1422 2114 145

8 4) 18 13.50 12.72 15.75 8 x 6 16.14 8.11 117.90 1800 1003 1422 2114 145


316 SS, Titanium Grade 5, Hastelloy®,Monel®, Duplex, Super Duplex


Options

Shaft Option

ElastomerOptions

Seat TFM

Body and Ball Material


Subject to media



Sizes 1” (25mm) – 8” (200mm) (1” - 6” full port, 8” is standard port)

AVT530


110°C / 230°F

AVT520


120°C / 250°F


shipham-valves.com

Wafer Check Valves - Corrosion resistant,two piece, fully composite with integralhinge and no metallic partsOperation

Designed for maximum strength and ruggedness, Shipham AVT check valves are

designed to be gravity operated, although in instances where spring assistance is

required, this can be accommodated using Inconel® X750 springs.

Full Flange Face Body

Shipham AVT Wafer Check Valves have a full face body which is supplied “through

drilled” with clearance holes for bolting. The valve can be used with Metallic or

composite flanges and do not require the use of special heavy duty GRE flanges.

They can be used as a direct replacement for similar valves designed to API 594,

Type A, class 150#. Most flange drilling can be accommodated.

Disc / Seat Design

Designed to have a minimum of parts the Shipham AVT Wafer Check Valve has a

one-piece integral disc and hinge. For general service, the valve will have “hard seat”

(composite to composite sealing) and sealing is to API 598. Where a higher integrity

seal, or where a soft seat is required for quieter operation, this can be

accommodated using elastomer seals.

• 2 Piece design for ease of construction and assembly

• Wafer construction - can easily be assembled in-line, using standard flat-face flanges

• Face to face dimensions comply with API 6D, ASME B16.10, and API 594 (See table for dimensions)


Others by request


ANSI 150, DIN, BS, ISO. Available drilled through or tapped.

Notes 1) Max WP for AVT 530 material, non-dangerous fluids at ambient temperature. AVT 520 is 80% of listed pressures. For other temperatures & fluids, please refer toShipham Valves

Inconel® X750

Options

Spring OptionBody, Disc and Hinge Material


Subject to media



Sizes 3” (80mm) – 12” (300mm)

AVT530


110°C / 230°F

AVT520


120°C / 250°F

Valve Size A B C H1 H2 Weight Max WP 1)

mm (Min Pipe Dia) Kg Bar

80 73 200 73.7 80 49 3.6 16

100 73 230 97.2 102 67 4.5 16

125 83 250 122.3 127 87 6.5 16

150 98 285 146.3 152 107 8.6 16

200 127 345 193.7 203 145 16.7 16

250 146 405 242.9 254 190 23.5 16

300 181 485 288.9 305 220 43 16

Dimensions for ANSI 150 Wafer Check Valves


Valve Size A B C H1 H2 Weight Max WP 1)

Inch (Min Pipe Dia) Ibs psi

3 3 8.15 2.90 3.15 1.93 8 230

4 3 9.06 3.83 4 2.64 10 230

5 3.27 9.84 4.81 5 3.43 14 230

6 3.9 11.22 5.76 6 4.21 19 230

8 5 13.58 7.625 8 5.71 37 230

10 5.75 15.94 9.56 10 7.48 52 230

12 7.125 19.09 11.37 12 8.66 95 230

Dimensions for ANSI 150 Wafer Check Valves


ElastomerOptions



shipham-valves.com

Chemical Resistance GuideShipham Valves’ range of Ball, Butterfly and Wafer

Check Valves are suitable for use in harsh

environments and for the applications as listed

opposite, and up to the maximum recommended

temperatures and pressures.

The guide covers the main chemical resistance properties of the specially formulatedmaterials used in Shipham AVT products (AVT530 and AVT520).

AVT 530 is a specially formulated bisphenol A based aromatic amine cured, glassreinforced Epoxy Resin System with a wide chemical resistance. This material givesthe highest pressure resistance available.

AVT 520 is a specifically formulated modified aromatic amine cured, glass reinforcedNovolac Epoxy Resin System and has an enhanced chemical resistance profile toAVT 530 and with a generally higher temperature range.

This data is based on specific concentrations of chemicals at stated temperaturesand has been extracted from several sources including controlled laboratory tests,field experience and historical performance, chemical structure and supplier’s data.

It should be noted that media containing suspended solids and / or variations fromthe temperature, concentration, or combinations of materials might offer synergisticeffects to the detriment of the valve.

This guide has been developed to assist designers in the application and selection ofcorrosion resistant products manufactured by Shipham AVT. The final determinationof the suitability of any Shipham AVT product for the application under considerationis the sole responsibility of the customer or their advisors.

Where, in the guide, no mention of any specific chemical or combination ofchemicals is made, or where the actual operating conditions of the application are near, at, or in excess of the indicated temperatures or concentrations stated,reference to Shipham AVT, or Shipham AVT’s authorised distributor, isrecommended.

The information provided is believed to be accurate, but it is intended as a guide onlyand reference should always be made to Shipham Valves Technical Department(contact via [email protected] ) for further guidance and for confirmationthat our valves are suitable for the intended purpose, or for applications not listed.

Shipham Valves make no warranties, expressed or implied, and assume no liability inconnection with any use to which it is put.


Media Name Media Conc Temp °C Temp °F AVT 520 AVT 530

Acetic Acid CH3CO.OH 25% 66 150 A B

Acetone C3H6O 100% 38 100 B D

Ammonium Hydroxide NH4OH 15% 66 150 A

DEION H2O H2O 100% 93 200 A A

Hydrochloric Acid HCl 20% 93 200 B C

Hydrochloric Acid HCl 37% 38 100 B C

Hydrogen Peroxide H2O2 10% 66 150 A B

Methanol, MEOH CH4O 100% 38 100 B D

Nitric Acid HNO3 5% 66 150 A B

Phenol C3H6O 6% 38 100 A D

Phosphoric Acid H3PO4 25% 66 150 A A

Sodium Hydroxide NAOH 100% 93 200 D D

Sodium Hypochlorite NAOCl 13.5% 38 100 B C

Sulfuric Acid H2SO4 25% 93 200 B D

Toluene C6H5C6H3 100% 38 100 A

Water:-

Water - Bilge 100% 100 212 A A

Water - Ballast 100% 100 212 A A

Water - Chlorinated 100ppm 100 212 A A

Water - Chlorinated Brine 6500ppm 60 140 A A

Water - Demineralised 100% 100 212 A A

Water - Deionised 100% 100 212 A A

Water - Distilled 100% 100 212 A A

Water - Fresh 100% 100 212 A A

Water - Sea 100% 100 212 A A

Water - Salt 100% 100 212 A A

Water - Treated 100% 100 212 A A

A Excellent

B Good, possibly limited temperature

C Fair. Limitations apply, not for continuous use

D Not recommended

Chemical Resistance Chart’


shipham-valves.com

Pressure : Temperature Graphs

DN80/3" to DN300/12"DN80/3" to DN300/12"

Ball Valves, Full and Reduced Port

Wafer Check Valves

Butterfly Valves (Preferred Direction)

Reduced Bore DN25/1" to DN150/6"

Reduced Bore DN200/8"

Reduced Bore DN25/1" to DN150/6"

Reduced Bore DN200/8"

Full Bore Full Bore


Type of Product10 Butterfly Valve, full flanged, tapped bolt holes (Threaded inserts)12 Butterfly Valve, full flanged, clearance bolt holes20 3 - Piece Ball Valve, Full Bore “O” ring shaft (DN25 / 1" to DN150 / 6"). ANSI 16.10 Long Pattern21 3 - Piece Ball Valve, Full Bore “Chevron” shaft (DN25 / 1" to DN 150 / 6"). ANSI 16.10 Long Pattern25 3 - Piece Ball Valve, Reduced Bore “O” ring shaft (DN200 / 8" only). ANSI 16.10 Long Pattern26 3 - Piece Ball Valve, Reduced Bore “Chevron” shaft (DN200 / 8" only). ANSI 16.10 Long Pattern60 1 - Piece Ball Valve, Reduced Bore “Chevron” shaft (DN25 / 1" to DN200 / 8") ANSI 16.10 Short pattern80 Wafer Check Valve, Swing Type - Hard seated’

Valve Sizes (Nominal Bore)025 DN 25mm / 1"040 DN 40mm / 1.5" 050 DN 50mm / 2"080 DN 80mm / 3" 100 DN 100mm / 4"150 DN 150mm / 6"200 DN 200mm / 8"250 DN 250mm / 10" 300 DN 300mm / 12"

Mating Flange DimensionsF1 ANSI 150#F2 PN10 *F3 PN16 *

Other Flange drilling is available - please consult Shipham Valves for options.

SeatsMaterial Ball Butterfly

4 EPDM Not available Standard5 Viton B Not available Option8 Nitrile NBR Not available Option9 TFM Standard Not availableA Viton A Not available Option

Other materials are available - please consult Shipham Valves for options.

Body Materials3 Novolac, Glass reinforced system AVT 520 body material5 Epoxy (Aromatic Amine) Glass reinforced system AVT 530 body material7 Epoxy glass reinforced system AVT 530 body material with Firesafe Intumescent coating

Disc / Ball Materials03 Novolac, Glass reinforced system AVT 52005 Epoxy (Aromatic Amine) Glass reinforced system AVT530

Seal And "O" Ring MaterialsA Viton AQ EPDMR Viton BV Nitrile

Shaft2 Stainless Steel 3163 Hastelloy B25 Titanium grade 58 Hastelloy C276K Monel K500Q DuplexU Super Duplex

How to specify AVT 13 digit assembly codes

Type Size

FlangeStyle /

PressureRating Seats Body Disc/Ball

‘O’Ring Shaft

Operation

Shipham AVT Butterfly & Ball Valves are generally supplied lever operated as standard, and unless otherwise specified.

Any conventional actuator (pneumatic, electric or hydraulic) or gear operator with standard ISO mounting may be fitted either at our factory or by our customer.

(Please advise your requirements)

Note

*PN10 and PN16 flange dimensions are the same up to and including DN150 / 6"


shipham-valves.com

Head Office/Factory:Hawthorn AvenueHullEast YorkshireHU3 5JXUnited Kingdom

Email: [email protected]: www.shipham-valves.comTel: +44 (0) 1482 323 163Fax: +44 (0) 1482 224 057

USA Sales Office:3202 Oakland DriveSugarlandTexas 77479USA

Email: [email protected]: +1 (281) 494 0660Fax: +1 (281) 494 0602

China Sales Office:4th Floor, Building 13No.170 Jinfeng Road, Pudong New DistrictShanghai 201201P.R. China

Email: [email protected]: +86 (21) 5858 5500 ext. 113Fax: +86 (21) 5858 7992

www.shipham-valves.com/worldwide.html

Shipham Valves is a trading division of Wärtsilä Valves Limited

www.wartsila.com/valves

Ref No: HQ134 Nov12 Rev5


Documents

The AVT Composite Valve Range - Shipham Valves€¦ · Others by request Notes 1) Max WP for AVT 530 material, non-dangerous fluids at ambient temperature. AVT 520 is 80% of listed