Tabla de Conversie

8/19/2019 Tabla de Conversie

http://slidepdf.com/reader/full/tabla-de-conversie 1/5

Tabla de conversie de mai jos permite conversia sistemului american de notare a cablurilor de cupru in sistemulechivalent european.



AWG Table

AWG=American Wire Gauge standard

Gauge Diam Area R I at 3A/mm2

AWG mm mm2 ohm/km mA

46 0,04 0,0013 13700 3,8

44 0,05 0,002 8750 6

42 0,06 0,0028 6070 9

41 0,07 0,0039 4460 12

40 0,08 0,005 3420 15

39 0,09 0,0064 2700 1938 0,1 0,0078 2190 24

37 0,11 0,0095 1810 28

0,12 0,011 1520 33

36 0,13 0,013 1300 40

35 0,14 0,015 1120 45

0,15 0,018 970 54

34 0,16 0,02 844 60

0,17 0,023 757 68

33 0,18 0,026 676 75

0,19 0,028 605 85

32 0,2 0,031 547 93

30 0,25 0,049 351 147

29 0,3 0,071 243 212

27 0,35 0,096 178 288

26 0,4 0,13 137 378

25 0,45 0,16 108 477

24 0,5 0,2 87,5 588

0,55 0,24 72,3 715

0,6 0,28 60,7 850

22 0,65 0,33 51,7 1,0

0,7 0,39 44,6 1,1

0,75 0,44 38,9 1,3

20 0,8 0,5 34,1 1,5



I am attempting to rite instructions !rom t"e #ideo i sa re$eased monda% oct 26t"& 'an an%one

proo! read to ma(e sure t"is is correct)

gat"er a t"in *ar

ac+uire 14 gauge copper ire

$ea#e 4 5 cm straig"t *e!ore ma(ing turns on t"e *ar

it" t"e ire ma(e anti c$oc(ise turns going up t"e *ar

*eteen 70 80 turns

pu$$ spring so t"ere is a sma$$ gap in *eteen turns

continue t"e ire past t"e spring !or a $engt" o! 1&5 times t"e springs $engt"

t"en ac+uire t"ic(er *ar *igger in diameter t"an t"e sma$$er spring

repeat steps to ma(e t"e $arger diameter spring

-ac+uire 14 gauge copper ire.

-it" t"e ire ma(e anti c$oc(ise turns going up t"e *ar.

-*eteen 70 80 turns.

-pu$$ spring so t"ere is a sma$$ gap in *eteen turns.

ta(e t"e $ong $engt" o! ire !rom t"e sma$$er spring and *ring it around t"e outside o! t"e sma$$er spring and !eed it in /t"roug" t"e side it" t"e 45cm piece o! ire protruding *ac( t"roug"

itse$!

insert t"e sma$$er spring t"roug" t"e $arger spring



t"is creates t"e inner com*ination o! springs

no to create t"e outer com*ination o! springs

o create t"e sma$$ diameter spring

--gat"er a t"in *ar..

--ac+uire 14 gauge copper ire..

--$ea#e 4 5 cm straig"t *e!ore ma(ing turns on t"e *ar ..

--it" t"e ire ma(e anti c$oc(ise turns going up t"e *ar..

--*eteen 150 160 turns..

--pu$$ spring so t"ere is a sma$$ gap in *eteen turns..

--continue t"e ire past t"e spring !or a $engt" o! 1&5 times t"e springs $engt"..

o create t"e $arge diameter spring

-- ac+uire t"ic(er *ar *igger in diameter t"an t"e sma$$er spring..

---ac+uire 14 gauge copper ire...

---it" t"e ire ma(e anti c$oc(ise turns going up t"e *ar...

---*eteen 150160 turns...

---pu$$ spring so t"ere is a sma$$ gap in *eteen turns...

---ta(e t"e $ong $engt" o! ire !rom t"e sma$$er spring and *ring it around t"e outside o! t"e

sma$$er spring and !eed it in /t"roug" t"e side it" t"e 45cm piece o! ire protruding *ac(

t"roug" itse$!...

---insert t"e sma$$er spring t"roug" t"e $arger spring...

"is is (non as one set

'reate 3 sets tota$

anocoat t"e sets



Documents

Tabla de Conversie