SWEN R2 User’s Manual SWEN R2 User’s Manual. Introduction Configuration Component Charging Power on/off Warming up Icons on the upper screen Buzzer on/off

SWEN R2User’s Manual

SWEN R2User’s Manual

<2>

• Introduction

• Configuration

• Component

• Charging

• Power on/off

• Warming up

• Icons on the upper screen

• Buzzer on/off

• Lamp on/off

• Setup of LCD bright

• Clock set

• Calibration

• Scanner operation

• Attentions

• Specifications & Features

INDEX

<3>

Without the necessity of bottle opening or content sampling, the SWEN R2 just

scans PET bottles and easily identifies the contents inside them. Our detector

employs a microwave using GPR (Ground Penetrating Radar) to identify contents,

which prevents users from being exposed to X-rays or other radiations and

chemical substances to be carefully used.

This detector employs microwave to penetrate most objects; thus even a very small

quantity of flammable substance can be detected. Its superior CPU with the high

speed performs the fast scanning within just one second. Such simple operation of

the SWEN R2 does not require additional personnel, thus labor costs could be kept

at a minimum.

Overview

<4>

[2] Case [3] Belt [4] Adapter [4] Key ring

[1] SWEN R2 Scanner

Configuration

<5>

DETECTING BUTTON

Components

<6>

[*] The icon of charging appears when the charging adapter is connected and the message that it started charging appears and then disappears.

Charging

<7>

1. The operation is initialized once power is on.

[*] The icon of charging appears when the charging adapter is connected and the message that it started charging appears and then disappears.

2. Success of system initialization

3. Failure of system initialization. In this case, re-trial of power-on or calibration is required.

Power on/off

<8>

Warming up After 10 seconds

After 10 seconds Press on the button

Warming up

Power Save

Wake Up

1 2

43

<9>

State of battery charging (4 phases)

Buzzer - off

Buzzer – on (warning messages & detecting beeping)

LED lamp-off

Current state of battery charging

LED lamp-on (during the detecting process)

Icons on the upper screen

<10>

Buzzer on/off

Buzzer - on

Buzzer - off

1. Press the menu key.


2. Move to the Buzzer through up/down cursor

2. Move to the Buzzer through up/down cursor



4. Buzzer on with beeping sound

4. Buzzer off

<11>



2. Move to the Lamp through up/down cursor

2. Move to the Lamp through up/down cursor



4. Lamp off

4. Lamp on with flickering

Lamp on/off

Lamp - on

Lamp - off

<12>


2. Move to the LCD Bright through up/down cursor


4. Adjust the bright level(1~5) through up/down cursor5. Press the menu

key for setup

Setup of LCD bright

<13>


2. Move to the Clockset through up/down cursor


4. Setup of time through up/down cursor

5. Move to the other part Through up/down cursor

6. Complete the clock set through the menu key

7. Return to menu screen after clock set

Clock set

<14>


2. Move to the Calibration through up/down cursor

4. Calibration is operating


5. Failure in calibration 7. Return to the menu screen

6. Success in calibration

7. Return to the menu screen

Start of calibration

Calibration

<15>

Scanner operation

Nonflammables

Inflammables

Put the subject like the image and press the sensor in the red circle.

Put the subject like the image and press the sensor in the red circle.

<16>

Liquid amount

1. The subject should be placed on the center of the sensor.

2. The proper amount of liquid is needed.

3. The subject cannot be scanned through being placed on floor (desk, or glass etc.).

Scanner operation

<17>

• This scanner is specified for DC9V.

• The unintended disassembly is not allowed.

• The unreasonable uses such as watering or forceful pressing can cause damages on the scanner.

• During the processes of Initialization and Calibration, there should be no subject affecting the sensor.

• In case of defecting the result of the sensor due to peripheral environment, the calibration or power-on should be conducted again.

• The conductive currents, glass or metal materials which are around the sensor can cause malfunctioning of the scanner.

• The user should be careful against the high voltage inside the scanner.

• Once the message of Low Battery appears, the battery should be charged promptly. Despite such usage, the continuous usage of the battery can be one factor of reduction in battery life.

Attentions

<18>

Type Principle of DetectionDetection Method Microwave Output

SWEN-R2 TypeSubstance identification by microwave Evaluation of the property of substance Less than 5mw (Detection within 5~8cm)

Detection Interval Real time - within one seconds

Result Notification Displayed on LCD panel and a buzzer goes off

Main Processor S3C840FX

Detection Process Automatic identification when placed on the surface of a subject

Power Source 7.4V 2400mA Li-ion battery

Power Consumption Operating Mode : Less then 500mA , Sleep mode : Less then 25mA

Battery charge time 8 hours

Adapter 9V 1000mA

Operational Condition -10~40 , 95%RH ℃

Size and WeightThe main unitW66×D400×H33mm / Weight : 540g

Specifications & Features

<19>

Thank youThank you

Documents

SWEN R2 User’s Manual SWEN R2 User’s Manual. Introduction Configuration Component Charging Power on/off Warming up Icons on the upper screen Buzzer on/off