Upload
dangtuyen
View
232
Download
0
Embed Size (px)
Citation preview
Product Bulletin
Wingtack® Resins
Oaklands Corporate Center • 468 Thomas Jones Way, Suite 100 • Exton, PA 19341877-871-2729
www.crayvalley.com
2
TABLE OF CONTENTS
INTRODUCTION TO WINGTACK® RESINS ..................................................................... 3
PHYSICAL AND CHEMICAL PROPERTIES .................................................................... 52.1 Specifications ....................................................................................................... 52.2 Typical properties ................................................................................................. 5
SOLUBILITY IN SOLVENTS AND COMPATIBILITY WITH POLYMERS ............................ 7
PACKAGING AND STORAGE/SAFETY DATA SHEETS ................................................ 8
COMPLIANCE WITH US FOOD CONTACT REGULATIONS........................................... 9
APPLICATIONS OF WINGTACK® RESINS. ................................................................... 10
3
Wingtack® hydrocarbon resins are synthetic resinsobtained by cationic polymerization of aliphatic mono-mers (C5). WINGTACK® is used in Pressure Sensi-tive Adhesives (PSA) as tackifying resin and in HotMelt Adhesive (HMA).
Because of their unique chemistry WINGTACK®
resins show outstanding properties:· Uniformity and consistency· Light color
· Low odour· High tack properties· Low specific gravity· Oxidative stability· Very low chloride levels
Wingtack® resins are also used as tackifying resins and/or “processing aids” (improvement of compounding,extrusion and molding properties) of EPDM, SBR,Polyisoprene, SIS, Butyl rubber based compounds,depending on their compatibility.
C9 modified C5
WT 10 WT 95 WT 98 WT RWT-7850
WT PLUS WT EXTRA WT ET WT STS WT 86
Isoprene compatible
Increasing Butadiene compatibility
Wingtack® resins are available having a variety of dif-ferent physical and chemical properties (like softeningpoint, glass transition temperature and molecular weightdistribution) each effecting the performance of the sys-tem as well as compatibility with various polymers andelastomers.
The two primary catagories of Wingtack® resins are1) aliphatic and 2) aromatically modified aliphaticresins.
1) Pure aliphatic resins:
Resin Type
Wingtack® 10 Liquid resin used as plasticizer. Better bleed resistance than oils.
Wingtack® 98 Designed for standard applications like packaging and masking tapes.
Wingtack® 95 Ideal for high performance applications in less polar elastomers (NR, SIS) and waxes.
Wingtack® RWT-7850 High softening point resin. Excellent for broad range of uses.
Introduction to Wingtack® Resins
Aromaticcontent
Pure C5
0
4
2) Aromatic-modified aliphatic resins:
Resin Type
Wingtack® PLUS Narrow molecular weight distribution. Best resin for use in SIS based high performance formulations.
Wingtack® EXTRA Good general purpose resin.
Wingtack® ET Low molecular weight and higher aromaticity for improved EVA and Butadiene compatibility. Partial replacement for Hydrogenated resins.
Wingtack® STS Medium softening point and broad range of compatibilities including SIS, SBS, SBR, SIBS and EVA.
Wingtack® 86 Low softening point resin. Broad range of compatibilities including SIS, SBS, SBR, SIBS and EVA.
5
Specification of Wingtack® resins
Typical properties of Wingtack® resins
Physical and Chemical Properties
Test method Wingtack
10 Wingtack
95 Wingtack
98 Wingtack
RWT-7850 Wingtack
PLUS Wingtack EXTRA
Wingtack ET
Wingtack STS
Wingtack 86
Appearance Pass or fail Visual Pass Pass Pass Pass Pass Pass Pass Pass Pass
Black spec Pass or fail E-656 Pass Pass Pass Pass Pass Pass Pass Pass
Softening point Ring and Ball, °C ISO 4625 98 ± 3 98 ± 4 102.5 ± 3 96.5 ± 3 97 ± 3 95.5 ± 3 94 ± 4 87 ± 3
Brookfield viscosity @ 25 °C, mPa.s E-958 30,000 ±
10,000
Gardner color (50% toluene solution) ISO 4630 ≤ 3 ≤ 3 ≤ 3.5 ≤ 3.5 ≤ 3 ≤ 3 ≤ 3 ≤ 3.5 ≤ 3
Gardner colorimeter RD E-803a 90 - 100 90 - 100 90 - 100 90 - 100 90 - 100 90 - 100 90 - 100 90 - 100 90 - 100
Wingtack 10
Wingtack 95
Wingtack 98
Wingtack RWT-7850
Wingtack PLUS
Wingtack EXTRA
Wingtack ET
Wingtack STS
Wingtack 86
Appearance Light yellow liquid
Light yellow solid
Light yellow solid
Light yellow solid
Light yellow solid
Light yellow solid
Light yellow solid
Light yellow solid
Light yellow solid
Softening Point Ring and Ball
10 °C
98 °C
98 °C
102 °C
96 °C
97 °C
95 °C
94 °C
87 °C
Brookfield Viscosity @ 25 °C 30,000 mPa.s
Gardner Color (50% toluene solution)
1.5
1.7
2.3
2.4
1.6
1.4
2.0
3.0
1.2
Specific Gravity @ 25 °C 0.9 0.94 0.95 0.95 0.95 0.96 0.96 0.97 0.98
Molar Weight (g/mol) :
Mn 370 1100 1000 1000 1000 1200 1000 1000 650
Mw 500 1700 2000 2100 1600 2200 1600 1600 1300
Mz 700 3000 3100 4500 2700 3900 3200 3100 2100
Polydispersity 1.4 1.5 2.0 2.1 1.6 1.8 1.6 1.6 2.0
Glass Transition Temperature Tg (°C, midpoint )
- 31 °C
51 °C
48 °C
56 °C
50 °C
52 °C
47 °C
44 °C
41 °C
6
Typical melt viscosity of Wingtack® 95, 98, Plus, Extra, ET, STS, 86
Typical viscosity of Wingtack® 10
Typical Molten Viscosity of Wingtack® 10
10
100
1000
10000
100000
20 30 40 50 60 70 80 90 100
Temperature (°C)
Visc
osity
(mPa
.s)
Typical Molten Viscosity of WINGTACK Resins
10
100
1 000
10 000
100 000
1 000 000
100 120 140 160 180 200
Temperature (°C)
Visc
osity
(mPa
.s) Wingtack® 95
Wingtack® EXTRAWingtack® 98Wingtack® PLUSWingtack® ETWingtack® STSWingtack® 86
7
Compatibility with polymers :
C : compatiblePC : partially compatibleI : incompatible
Solubility of solventsWingtack® resins are generally soluble in solventshaving low to medium polarity like:· Aromatic hydrocarbons· Aliphatic hydrocarbons
· Higher ketones· Higher acetates· Chlorinated solvents· Higher alcohols
Solubility in Solvents and Compatibility with Polymers
Wingtack 10
Wingtack 95
Wingtack 98
Wingtack RWT-7850
Wingtack PLUS
Wingtack EXTRA
Wingtack ET
Wingtack STS
Wingtack 86
Butyl rubber
C C C C C C C C C
Chlorobutyl rubber
C PC PC PC PC PC PC PC C
Natural rubber C C C C C C C C C
Nitrile rubber PC PC PC PC PC PC PC PC PC
Waxes C C C C C C C C C
Ethylene-alphaolefin copolymers
C C C C C C C C C
EPDM C C C C C C C C C
EVA VA <28% C C C C C C C C C
28%<VA<40% C PC PC PC PC PC PC PC C VA ≥ 40% C I I I I I I PC C
Polybutadiene
C PC PC PC PC PC PC PC C
Low MW polyethylene
C C C C C C C C C
Polyiso-butylene
C PC PC PC PC PC PC PC PC
Polyisoprene C C C C C C C C C
Amorphous polypropylene C C C C C C C C C
PVC PC PC PC PC PC PC PC PC PC
SBR C PC PC PC PC PC PC PC C
SBS C PC PC PC PC PC PC C C
SIS C C C C C C C C C
8
Packaging and storage
Packaging: Wingtack® 10 liquid resin is packaged in4x172kg drums on wood pallet ( 689 kg ). Wingtack®
solid resins are packaged in 25kg paper bags, 45bags on wood pallet ( 1125kg).
Storage : all resins with a low softening point present arisk of solidifying, which increases in hot weather.Therefore, for softening points of less or equal to100°C, we recommend : storage in a cool ( 25 °Cmax ), ventilated area, out of the sunlight; do not stackpallets; avoid storage for prolonged period.
Wingtack 86 : due to low softening point, seriousremassing of product may occur when exposed toelevated temperatures. Customer accepts theresponsibility for using remassed material.
Safety Data Sheets
The Safety Data Sheets (SDS) are available on theCRAY VALLEY website: http://www.crayvalley.com
Packaging and Storage/Safety Data Sheets
9
1 – In contact with poultry, dry food and dehydrated fruits and vegetables2 – Limited to 47.5% in final adhesive formulation3 – Food Contact Notification, listed on FDA website4 – In contact with raw fruits and raw vegetables5 – Total plasticizer (Wingtacks) not to exceed 30% by weight of rubber product6 – Not to be used at less than 50% of total solids7 – Cements may contain up to 30% by weight of terpolymer; cans may be used in contact with all types of food under Condition of hightemperature heat sterilized through frozen or refrigerated storage8 – Blended with butyl rubber as a coating for polyolefin films used in bulk packaging of raw fruits and vegetables, 30% by weight of coating9 – Petroleum hydrocarbon resins (alicyclic) for use as modifiers in waxpolymer blend coatings for corrugated paperboard intended for use in bulkpackaging of raw fruits, raw vegetables, iced meat, iced fish and iced poultry; and limited to use at a level not to exceed 30 weight-percent of thecoating solids10 – Not to exceed 30% by weight of the waxpolymer blend coatings
* These products have been determined to be compliant with the applicable FDA regulation for incorporation into the specified food-contactarticles. It is the responsibility of the manufacturer of the finished food-contact article to ensure that the article complies with extractionlimitations and other provisions applicable to its intended use.
Compliance with US Food Contact Regulations (Food and Drug Administration)*
Wingtack Product 10 95 98 RWT 7850 PLUS EXTRA ET STS 86
175.105 (c)(5) Adhesives
175.125 (a) Pressure sensitive adhesives1,2,3
175.125 (b) Pressure sensitive adhesives4 2, 3 2, 3 2, 3 2, 3 2, 3
175.300 (b)(3)(xi) Resinous and polymeric coatings (incl. can end cements )
175.300 (b)(3)(xxxi) Can end cements (only) 3, 7 3, 7 3, 7 3, 7 3, 7
175.320 (b)(3)(i) Resinous coatings on polyolefin films 8 8
176.170 Components of paper & paperboard in contact w/aq. & fatty foods
9 9
176.180 (b)(1) Components of paper & paperboard in contact with dry foods
10 10
177.1210 (b) Closures with sealing gaskets for food containers
177.2600 (c)(4)(iv) Rubber articles intended for repeated use5
178.3800 (b) Preservatives for wood6
Acceptable for use Subject to testing and data review Subject to future Food Contact Notification
10
These results obtained in our laboratory are given in good faith according to the method used and the samples checked. Thevalues cannot be used to set specifications. They are indicated without Cray Valley’s guarantee or liability. All given formula-tions are starting formulations and they are indicated without Cray Valley’s guarantee or liability. They are based on our presenttechnical knowledge and experience. They do not relieve processors of the responsibility of carrying out their own tests andexperiments, because many factors that could influence the result may arise during processing and application; neither do theyimply or give legally binding assurance of certain properties or of suitability for a specific purpose. Any proprietary formulationshould be respected.
Application of Wingtack® Resins
Suggested uses Wingtack 10
Wingtack 95
Wingtack 98
Wingtack RWT-7850
Wingtack Plus
Wingtack Extra
Wingtack ET
Wingtack STS
Wingtack 86
-Tackifier and plasticizer for hot melt, solvent-borne and water-borne pressure sensitive adhesives.
√ √ √ √ √ √ √ √ √
-Modifying resins for hot melt adhesives, EVA and wax coatings, and sealants.
√ √ √ √ √ √ √ √ √
-Pressure Sensitive Adhesives (PSA) :
.low temperature tapes √ √ √ √ √ √ √ .carton sealing tapes √ √ √ √ √ √ √ √
.general purpose labels √ √ √ √ √ √ .surgical tapes √ √ √ √ √ √ √ √ .masking tapes √ √ √ √ √ √ √
.hot melt √ √ √ √ √ √ √ √ √ .water-borne √ √ √ √ √ √ √ √
.solvent borne √ √ √ √ √ √ √ √ √ -Hot melt adhesives :
.bookbinding √ √ √ √ √ .EVA based HMA for non-
woven assembly √ √ √ √
.hot melt PET bottle √ √ √ .general purpose √ √ √ √ √ √ √ √
-Contact adhesives √ √ √ √ -Elastomeric adhesives for non-woven assembly
√ √ √ √ √
-Mastic construction adhesives √ √ √ √
-Mastics general purpose √ √ √ √ √ √ √ √ -Road marking √ √ √ √ √ -Processing Aid in rubber compounding √ √ √ √ √ √
11
3911 01/10
Corporate Headquarters
Cray Valley USA, LLC468 Thomas Jones Way, Suite 100
Exton, PA 19341
Tel: 877-US1-CRAY (877-871-2729)
E-mail: [email protected]
For contact information worldwide, please refer to Cray Valley's web site at:http://www.crayvalley.com
The information in this bulletin is believed to be accurate, but all recommendations are made without warranty since the conditions of use are beyond Cray Valley Company'scontrol. The listed properties are illustrative only, and not product specifications. Cray Valley Company disclaims any liability in connection with the use of the information,
and does not warrant against infringement by reason of the use of its products in combination with other material or in any process.