Nik rosli Abdullah 2012 - Universiti Teknologi MARA · PDF fileDr. Nik Rosli Abdullah is also registered with Board of Engineers Malaysia ... Universiti Teknologi MARA ... Contract

[NIK ROSLI ABDULLAH 2015] OCT 2015

Page 1

NIK ROSLI ABDULLAH (Assoc. Prof. Dr.)

Dr. Nik Rosli Abdullah obtained Bachelor of Mechanical Engineering (1st Class) in1999 from

University Malaya and a Master of Science in Mechanical Engineering in 2003 from the

University of Sheffield, UK. Dr. Nik Rosli Abdullah obtained his DOCTOR OF PHILOSOPHY

in Mechanical Engineering (Internal Combustion Engine and Alternative Fuels) in March 2011

from the University of Birmingham, UK. After finishing his PhD., he worked as a research

fellow at Birmingham University in collaboration with Jaguar Land Rover UK. This project was

funded by the UK Government and the Technology Strategy Board in collaboration with Jaguar

Cars with a total budget of GBP2.12 million. While working as a research fellow, he supervised

one PhD and one Master student. He has published a number of technical papers in very

reputable journals and international conferences in the area of internal combustion engine,

energy efficiency, engine performance, exhaust emissions and alternative green fuels. In

addition, Dr. Nik Rosli Abdullah was the Head of Bachelor Programme UiTM from the year

2005-2007, and the Deputy Dean (Academic) from the year 2012 – present at the Faculty of

Mechanical Engineering, UiTM Shah Alam, Malaysia.

His present research interests are combustion and emissions of Spark-Ignition (SI) and

Compressed-Ignition (CI) engines, combustion strategies, fuel injection strategies, alternative

future green fuels, fuel spray behaviour, modelling air flow and thermal stress analysis on Diesel

Particulate Filter (DPF). Dr. Nik Rosli Abdullah is also registered with Board of Engineers

Malaysia, International Association of Engineers (IAENG), Member of Malaysian Tribology

Society (MYTRIBOS), Malaysian Invention & Design Society (MINDS) and Society of

Engineering Education Malaysia (SEEM).

Current Appointment

Deputy Dean (Academic)

Office Address

Faculty of Mechanical Engineering, Universiti Teknologi MARA

40450 Shah Alam, Selangor Darul Ehsan

Tel: +603-5543 5150, Mobile +6012 3641119 Fax: 5543-5160

Marital Status

Married with four children.


Page 2

Nationality Malaysian

BORN

10th

April, 1975

Kelantan

Email: [email protected]

[email protected].

OBJECTIVE

To serve the university as a lecturer and to lead and manage teams or sub-societies,

present or in the future; in order to satisfy multi stake-holders and for self-satisfaction.

To keep upgrading professional personal and career development by attending courses,

workshops, trainings, research activities, publication, consultancy works, involving with

social works and etc.

To explore and develop expertise in the area of internal combustion engines, alternative

fuels, after-treatment devices, engine combustion strategies, computer simulation, fuel

economy and renewable and sustainable energy technologies.

STRENGHTS

Excellence in teaching and learning.

Academic leadership and ability to motivate others.

Decision making skills (ability to understand argument and work collaboratively to reach

a decision).

Ability to relate to students and staff.

Fast learner, creative and idealistic.

Enjoy taking on leadership roles and decision making in various capacities.

Dynamic and active in working and goal oriented.

Experienced in conducting research and talk in the area of internal combustion engines,

combustion behavior, fuel properties, after-treatment devices and fuel spray behavior.

Invited speaker for student leadership development programme and OBE

implementation.

National and international judge for innovation competition.

COMPUTER SKILLS

CAD/CAM: Unigraphies software, AutoCAD, CATIA, SOLIDWORKS.

MS Project; visual Basic

Programming Language: Q-Basic, Fortran, etc.

FLUENT.

mailto:[email protected]



Page 3

A: RESEARCH AND TEACHING AREAS

Thermodynamics.

Thermal Engineering.

Internal Combustion Engines.

Fluid Mechanics.

Heat Transfer.

Air Conditioning System

Renewable and Sustainable Energy.

Fuel Properties and Characteristics.

Fuel Spray Behaviors.

Engine power-train and emissions.

Alternative/Green Fuels.

Engine Experimental and Technical Set up.

B: EDUCATION/ACADEMIC QUALIFICATION/FIELD/INSTITUTION

AND YEARS OF AWARD

1. Bachelor of Mechanical Engineering(1st Class), University of Malaya, Malaysia (1999)

2. Master of Science (Research) In Automotive Engineering, University of Sheffield, UK

(2003)

The aim of the research was to investigate the type of wear inside the combustion chamber

particularly on the cylinder liner and piston rings. Lamb waves were used to measure the torn

or wear surface at different states of surface roughness. The signal of lamb waves were

excited and captured by using piezoelectric. The results showed that the lamb waves had a

capability to differentiate different wear types and potential to be used as an alternative

method to measure wear inside the engine components.

3. PhD in Mechanical Engineering (Internal Combustion Engines), University of

Birmingham, UK (2011)

The aim of the research was to investigate the combustion characteristics and exhaust

emissions through combustion strategies using 2.7L and 3.0L modern V6 diesel engines

fuelled with fossil diesel and TME-diesel blends. The initial work was based on the advanced

combustion strategy on a modern V6 diesel engine fuelled with fossil diesel and TME-diesel

blends in order to meet future emissions legislation. The principle relied on high fuel

injection pressure, variation of injection timings, and variation of pilot fuel quantities and

cooled EGR. This approach lead to a new advanced combustion strategy that offers low

emissions, high power output and low fuel consumption. This work was a collaboration of

University of Birmingham with other parties such as Jaguar Land Rover, Shell Global


Page 4

Solution UK, Green Fuel Ltd, Johnson Matthey Plc and partly funded by Technology

Strategy Board (Department of Industry, UK Government).

C: PROFESSIONAL QUALIFICATION / MEMBERSHIP IN

PROFESSIONAL BODIES

1. Graduate Member, B.E.M (Board of Engineers Malaysia)- 49261A

2. International Association of Engineers (IAENG) - 106273

3. Member of Malaysian Tribology Society (MYTRIBOS) – L0412

4. Malaysian Invention & Design Society (MINDS) – 2033

5. Member of Science Engineering Education Malaysia (SEEM)

D: WORKING EXPERIENCE

1. FACULTY OF MECHANICAL ENGINEERING, UiTM, MALAYSIA.

Permanent Lecturer (October 2003 -present)

1. Responsible to represent and promote the interests of the University.

2. Leading personnel for the process of initiating, reviewing and developing new and

existing programmes (Diploma, Bachelor and Master).

3. Leading personnel in the accreditation activities for the bachelor programme

(EM220 and EM221) by Engineering Accreditation Council (EAC).

4. Manage to monitor and act upon annual monitoring reports for undergraduate and

taught postgraduate programmes. Example: External Examiners’ reports,

accreditation reports, student feedback and formal written student complaints.

Responsible to disseminate and implement good practice identified in these

reports across the Faculty.

5. Responsible for the improvement of Teaching and Learning in the faculty to

ensure that the offered programmes are of high academic quality, aligned with

relevant professional benchmarks; providing the best possible experience for

students.

6. Responsible to formulate, develop, implement, update and audit academic

activities i.e Teaching and Learning.

7. Responsible to develop plans specifically to improve the student performance,

experience and soft skills within the faculty.

8. Participated in marketing campaigns to promote the mechanical engineering

programmes. In particular, in providing subject matter expertise for the creation

of marketing content for the faculty for open days/fairs/careers events etc.


Page 5

9. Liaise with the management to assist in the recruitment, training and on-going

appraisal of faculty members.

10. Responsible to promote and market the graduates of the mechanical engineering

programmes both nationally and internationally.

11. Involved in development and application of a new approach of teaching-learning

activities: Conceive-Design-Implement-Operate, CDIO (the approach helps to

map and inter-connect overall programme lesson plans, guide and groom students

in better ways of thinking, organize their knowledge, soft skills in implementing

or creating a specific project or product based).

1122.. Guide and support young lecturers in teaching-learning, research involvement,

research grant applications and management activities.

1133.. Develop national and international industrial linkage in research, student’s project

supervision and consultancy work.

14. Involvement in national and international activities: paper presentation in

conference and paper publication, conference proceeding and journal reviewer,

professional bodies. Organise national and international conferences.

15. Responsible in preparing lessons taught in Bachelor in Mechanical Engineering

courses such as Internal Combustion Engines, Automotive Technology,

Thermodynamics, Heat Transfer, Fluid Mechanics, Dynamic Machine and

renewable energy.

16. Lectures in undergraduate courses in Thermo fluids and Energy (Renewable

energy, Bio-fuels, Sustainability, Energy Power Generation, Thermodynamics,

Heat Transfer, Air Conditioning, Refrigeration system, Fluid Mechanics, internal

combustion engine and gas emissions).

17. Involvement in creating and developing a number of courses at Universiti

Teknologi MARA, UiTM such as Thermodynamics, Heat Transfer, Renewable

Energy, Internal Combustion Engine etc.

18. Acting as a Course Coordinator for Renewable and Sustainable Energy

Technology, Thermodynamics etc. that coordinated academically and prepared

syllabus for the curriculum review activities.


Page 6

2. FACULTY OF MECHANICAL ENGINEERING, UNIVERSITY OF

BIRMINGHAM, UK.

Research Fellow (2011)

This research investigated the relationship between fuel properties of biodiesel blends

(currently on market and future market)and engine emissions on modern V6 common rail

direct injection diesel engine. Biodiesel is a renewable fuel that consists of the alkyl

monoesters of fatty acids. It has been considered as an alternative diesel fuel for internal

combustion engines due to its efficiency, cleanliness and biodegradability. This research

is a collaboration between University of Birmingham, Jaguar Land Rover UK, Johnson

Matthey, Green Fuel UK, Shell Global Solution UK and TSB UK. The total amount of

grant is approximately GBP 2.2 million.

The research aimed to provide technical solutions that allowed the diesel engine to

operate with a diverse range of renewable fuels and it had two major objectives: 1) to

identify the changes required by the engine system (including after-treatment) to run on

blends containing up to 30% of a variety of both generations bio-diesel fuels; 2) to

develop novel 'Flex-diesel' technologies involving onboard pre- and after-treatment to

maintain optimized engine performance and emissions with increasing percentages of

fully sustainable bio-fuels and thermal management.

Results generated from this experimental work can support and aid the understanding of

combustion characteristics when engine is fueled with a variety of bio-diesel fuels which

may be found in future world markets.

The main tasks as a research fellow are shown below:

1. Responsible to plan and develop research contributions to subject area using

methodologies, critical evaluations, interpretations and analyses through correct

interpretation of the project objectives.

2. Responsible to propose and contribute to the development of research techniques,

models and methods in collaboration with colleagues.

3. Responsible in data analysis and interpretation of the results from own research

and generate ideas based on the outcomes.

4. Manage to coordinate activities with industrial partners and suppliers.

5. Responsible to achieve agreed research objectives/targets timely, involving

‘hands-on’ implementation of the research plan in general.

6. Manage to present/disseminate research findings using appropriate and effective

media such as publication, research seminars etc, involving the preparation of

research reports and technical papers.


Page 7

7. Manage to provide guidance/assistance to other staff and students on own

specialist area and work as part of a team.

8. Supervised students on research related work and provide guidance to PhD and

Master Students.

9. Participated in relevant paperwork preparation as required by a research group.

10. Responsible for the development of research objectives and proposals.

11. Accountable for collection of research data; through a variety of research

methods, such as scientific experimentation, literature reviews, and research

interviews.

12. Manage to present research outputs, including drafting academic publications

such as journal publication and poster presentation.

13. Responsible to deal with problems that may affect the achievement of research

objectives and deadlines.

14. Successfully complete a project within the time schedule.

3. FACULTY OF MECHANICAL ENGINEERING, UiTM, SHAH ALAM, SELANGOR,

MALAYSIA.

Contract Lecturer (July 2001 – September 2002)

1. Prepared notes and had large share of teaching of Diploma in Mechanical

Engineering for courses such as Internal Combustion Engines, Automotive

Electric Technology, Thermodynamics, Heat Transfer, Fluid Mechanics and

Dynamic Machine.

2. Co-ordinated and managed the development of Automotive Laboratories -

including preparation of extensive documentation (instructions) and management

of demonstrators.

3. Academic programme development and supervision skills for Diploma in

Mechanical Engineering.

4. Further study in Master of Automotive Engineering at Sheffield University, UK

under Young Lecturer Scheme UiTM September 2002 - October 2003.

4. PERODUA ASSEMBLY SHOP SDN. BHD.RAWANG SELANGOR, MALAYSIA.

Production Engineer(Sept 1999- Jun 2001)

1. Full responsibility onthe Assembly Shop (Kembara and Kenari Model) including

productionengineering, line management, part logistic, product quality, downtime


Page 8

and production planning & control. Manage a total manpower of about 107

personnel (night and day shifts).

2. Manage to arrange the processes of new model and new tact time through the

improvement of the production rate; and standardization of the format for the

inventory and standard operation procedure (SOP).

3. Responsibilities in design (Kaizen) activities to improve the production rate,

downtime and product quality.

4. Responsiblefor the production activities and implementation of the concept of 4M

(Man, Machine, Material and Method) to improve production rate and planning

activities.

5. Responsiblefor the production line operation, product quality,production rate, line

maintance, downtime, new layout, parts logistic, production control, line

administration (including training and manpower development) and Research &

Development in product quality and downtime.

6. Responsible for the part minimization and cost effective on production line

(Kembara and Kenari Line).

7. Assembly Shop Linemanager of a new model development of Kenari that focus

on part installation, line layout and quality. Developed strategies for the assembly

shop to set up new line layout and part arrangement for both model Kembara and

Kenari.

8. Implemented plant improvement activities including Total Productive

Maintenance TQM), Kanban System and quality improvement.

9. Participated in K-Car Project.

10. Liaise with the management to assist in the recruitment, training and on-going

appraisal of staff.

5. FACULTY OF MECHANICAL ENGINEERING, UM, KUALA LUMPUR,

MALAYSIA.

Research Assistant (Jun 1999- September 1999)

The research was to investigate the effect of natural gas and gasoline fuel to the engine

performance and emissions on1.6 12V Magma engine. Better performance with improved

fuel economy and lower exhaust emissions were two different objectives which were

difficult to be achieved at the same time. Introducing more air into the air fuel mixture

was the possible method to improve the combustion process resulted in higher power

output. The research aims to investigate the combustion characteristics and emissions

when engine fuelled with two different fuels. These results provided technical solutions

to the engine manufacturer that will allow the gasoline engine to operate with a natural


Page 9

gas as a renewable fuel. The results showed that natural gas has promising results in term

of emissions but slightly lower in engine power output.

Overall responsibilities as a research fellow are listed below:

1. Responsible in the planning and development of the experimental works related to

the project objectives.

2. Responsible to propose and contribute to the development of experimental works.

3. Responsible to generate data analysis and interpretation of the results.

4. Manage to present/disseminate research findings through group presentation.

5. Manage to provide guidance/assistance to other staff and students.

E: PREVIOUS RESEARCH - (Completed)

1) Application of Lamb Waves in Wear Detection on Aluminium Plate.

BRC Grant): RM 20,000

Nik Rosli Abdullah ( Leader)

Member:

1.Muhammad Hussain Ismail

2.Shahrul Azam Abdullah

This research explores the ability of lamb waves to detect a micro wear on aluminium

plate. This is an initial stage to find a non destructive testing to detect a micro wear inside

combustion chamber and in-cylinder surface of internal combustion engines.

2) The Design and Development Of A Turbojet Combustion Equipped With

Turbulence Chamber As Thrust Booster.

Short Term Grant (BRC Grant) : RM 26,500.00

RM26,500.00 Nik Rosli Abdullah ( Leader)

Member:

1. Assoc. Prof. Dr Rahim Atan

2. Mohd AzmanYahya

The research activities are more on design and fabricate the turbine blade for turbojet

combustion. This is important to increase the amount of air for the complete combustion.

The finding from this research activity is useful for the manufacturer to develop a new

design of turbine for high performance of combustion.


Page 10

3) Development of A Dual-Mode Fixed Bed Combustion Chamber For Solid Waste

Fuels.

Grant (BRC Grant) : RM 20,000

Wan Ahmad Najmi (Leader)

Member:

1. Nik Rosli Abdullah

The research explores availability of energy from waste solid fuel by burning inside the

combustion chamber. The availability of energy is measure based on heating value that

produced from the combustion. In future, the renewable energy is important due to high

fuel price and green house gases issues.

Major research interests

Currently, I’m working with combustion and emissions of diesel engines, fuel injection

strategies, Fuel properties, Biodiesels and Performance, fuel spray behavior, fuel additives,

combustion modes and modeling on air flow and thermal stress in Diesel Particulate Filter

(DPF).

F: PUBLICATIONS

Thesis

1. Nik Rosli Abdullah, “Effects of split injection and exhaust gas recirculation strategies on

combustion and emissions characteristics in a modern V6 diesel engine”, PhD. Thesis,

University of Birmingham, UK 2011.

2. Nik Rosli Abdullah, “Micro wear detection using Lamb waves”, MSc. Thesis, University

of Sheffield, UK, 2002.

3. Nik Rosli Abdullah, “Engine performance, emissions and wear rate of petrol engine 12-

Valve Magma fuelled with gasoline and LPG, Degree Thesis, University of Malaya,

Malaysia, 1999.

Research Report

1. Nik Rosli Abdullah, Shahrul Azam Abdullah and Muhammad Hussain Ismail, ‘The

application of Lamb waves to detect wear on the aluminum plate’, Bureau Research and

Consultancy, UiTM, December 2005.

2. Wan Ahmad Najmi Wan Muhamad and Nik Rosli Abdullah “Development of A Dual-

Mode Fixed Bed Combustion Chamber For Solid Waste Fuels. Bureau Research and

Consultancy, UiTM, December 2008.


Page 11

3. Jaguar Cars Ltd, Johnson Matthey plc, Shell Global Solutions (Glenn Wilson, Chris

Beck, Amir Abdul-Manan, Bob Head) Green Fuels Ltd.(Colin Hygate, JamesHygate) and

University of Birmingham.

Flex-diesel Engines with Sustainable Bio-fuels forClean and Efficient On- and Off-Road

Vehicles. University of Birmingham, UK. September 2011.

Book Chapter

1. T Gardiner, J Gaade, Jaguar and Land-Rover Advanced Powertrain Engineering, UK; B

Head, Shell GlobalSolutions, UK; C Hygate, Greenfuels; HM Xu, NR Abdullah,

University of Birmingham, UK “Research into requirements for worldwide sustainable

biodiesel capability.

ISBN- 0857092057 (online)

ISBN-13: 978 0 85709 205 2 (Hardcopy)

Institution of Mechanical Engineers (IMechE); Internal Combustion Engines: Improving

performance, fuel economy and emissions. November 2011.

Selected Journal Papers

1. R. Mamat, N.R.Abdullah, H.M. Xu, M.L.Wyszynski, A.Tsolakis, “Effect of Fuel

Temperature on Combustion and Emissions of a Common Rail Diesel Engine SAE

International Powertrains, Fuels and Lubricants, SAE Paper No. 2009-01-1896.

2. N.R.Abdullah, R. Mamat, P. Rounce , A.Tsolakis, M.L.Wyszynski, H.M. Xu, “Effect of

Injection Pressure with Split Injection in a V6 Diesel Engine. SAE 2009-24-0049, 2009.

3. N.R.Abdullah, R. Mamat, P. Rounce , A.Tsolakis, M.L.Wyszynski, H.M. Xu, G.Tian,

“The Effect of Injection Pressure and Strategy in a Jaguar V6 Diesel Engine”. Journal of

KONES (Internal Combustion Engines, European Science Society of Power train and

Transport Publication). ISSN 1231-4005, Vol 16, pp 9-22. 2009.

4. N.R.Abdullah, M.L.Wyszynski, A.Tsolakis, R.Mamat, H.M.Xu, G.Tian, “Combined

effects of pilot quantity, injection pressure and dwell periods on the combustion and

emissions behaviour of a modern V6 diesel engine”. Journal of Archivum Combustions ,

ISSN 0208-4198, pp 481-495, Vol 30-2010-No.4, September 2010.

5. W.A.Najmi W.M and NR Abdullah,” Combustion characteristics of Palm Shells and

Palm Fibers Using an Inclined Grate Combustor”. Journal of Mechanical Engineering,

FKM, UiTM, Vol 5, October 2011.

6. Rizalman Mamat, Rafidah Rahim, Abdul Adam Abdullah, Amir Aziz, Nik Rosli

Abdullah, Characteristic of Biodiesel Fuel Derived from Palm Oil, Journal of Biobased

Materials and Bioenergy, ISSN: 1556-6560. Volume 7, Number 4, August 2013, pp. 457-

460(4); Index: SCOPUS, H Index 12, Q3, IF=1.037.


Page 12

7. Rizalman Mamat, Ahmad Fitri Yusop, Abdul Adam Abdullah, Amir Aziz, Nik Rosli

Abdullah, Effect of EGR and Air Temperature on Exhaust Emission of a Diesel Engine

Operating with Biodiesel, Journal of Biobased Materials and Bioenergy, ISSN: 1556-

6560. Volume 7, Number 4, August 2013, pp. 461-463(3); Index: SCOPUS, H Index 12,

Q3, IF=1.037.

8. M.A. Mokhri, N.R. Abdullah, S.A. Abdullah, S. Kasalong, R. Mamat, Soot Filtration

Recent Simulation Analysis in Diesel Particulate Filter (DPF). International Symposium

on Robotics and Intelligent Sensors 2012 (IRIS 2012) Procedia Engineering 41 ( 2012 )

1750 – 1755. ISSN:1877-7058; Index: SCOPUS, H Index 7, Q3

9. Shahrul Azam Abdullah, Aidah Jumahat, Nik Rosli Abdullah, and Lars Frormann.

Determination of Shape Fixity and Shape Recovery Rate of Carbon Nanotube-filled

Shape Memory Polymer Nanocomposites. International Symposium on Robotics and

Intelligent Sensors 2012 (IRIS 2012) Procedia Engineering 41 ( 2012 ) 1641 – 1646;

ISSN:1877-7058; Index: SCOPUS, H Index 7, Q3

10. Mohamad Ali Ahmad, Salmiah Kasolang, Rob Dwjer-Joyce and Nik Rosli Abdullah.

The Effect of Oil Supply Pressure on the Circumferential Pressure Profile in

Hydrodynamic Journal Bearing. Applied Mechanics and Materials Journal, vol 315

(2013), pp 809-814; ISSN:16609336; Index: SCOPUS, H Index 9, Q4,

11. M. Mazlan, A.M. Mustafa Al Bakri, Huck-Soo Loo, Abdullah. N.R., M.A. Iqbal,

M.S.Abdul. Aziz, M.A. Sulaiman. The Comparison Between Thermal Pad Made of

Nano-Silver and Silicon Elastomer Using Computational Fluid Dynamic (CFD)

Software, FLUENTTM, Australian Journal of Basic and Applied Sciences, 7(5): 196-

204, 2013 ISSN 1991-8178; Index: SCOPUS, H Index 10, Q3.

12. M. Mazlan, A.M. Mustafa Al Bakri, Huck-Soo Loo, Abdullah. N.R., M.A. Iqbal, M.S.

Abdul Aziz, M.A. Sulaiman, M. Sarizam. Three Dimensional Analysis of Thermal Pad

made of Nanomaterial, Nano-Silver with differences of Thickness by Using CFD

Software, FLUENT, Australian Journal of Basic and Applied Sciences, 7(5): 220-229,

2013 ISSN 1991-8178. Index: SCOPUS, H Index 10, Q3.

13. Ismail Mustapha, Samihah Mustaffha, Md FakarudinAb Rahman, RoslanYahya,

Lahasen@ Norman Shah Dahing, Nor Pa’iza Mohd Hassan, Jaafar Abdullah and Nik

Rosli Abdullah. Neutron Backscattered Technique for Quantification of Oil Palm Fruit

Oil Content. Jurnal Sains Nuklear Malaysia, 2013, Vol. 25(1):32-36 ISSN: 2232-0946.

14. Nik Rosli Abdullah, Rizalman Mamat, M.L.Wyszynski, A.Tsolakis, H.M.Xu. “Effects

of Pilot Injection Timing and EGR On a Modern V6 Common Rail Direct Injection

Diesel engine” Journal of Materials Science and Engineering Vol 50 (2013) 012008.

15. Syarifah Yunus, N.R. Abdullah, R.Mamat, A.A. Rashid “On Overview of Palm,

Jathropha and Algae As a Potential Biodiesel Feedstock in Malaysia ”Journal of

Materials Science and Engineering 50 (2013) 012055.


Page 13

16. Shafiq Suhaimi, Rizalman Mamat, Nik Rosli Abdullah “Investigation of The Effects of

Inlet System Configuration on The Airflow Characteristics ”Journal of Materials Science

and Engineering 50 (2013) 012009.

17. M.H.Yasin, R.Mamat, A.A. Abdullah, N.R.Abdullah and M.L.Wyszynski. Cycle-to-

Cycle Variations of a Diesel Engine Operating With Palm Biodiesel. Journal of KONES

Powertrain and Transport, Vol 20. No. 3 2013.

18. Nik Rosli Abdullah, Muhammad izzat Nor, Ismail Nasiruddin, Salmiah Kasolang, Nor

Hayati Saad ”Potential Utilization of Biodiesel as Alternative Fuel for Compression

Ignition Engines in Malaysia” Applied Mechanics and materials Vol. 393 pp 475-480

August 2013; ISSN:16609336; Index: SCOPUS, H Index 9, Q4

19. Syarifah Yunus, Amirul Abd Rashid, Syazuan Abdul Latip, Nik Rosli Abdullah,

Rizalman Mamat, Abdul Hakim Abdullah “ Performance and Emissions of Jatropha-

Palm Blended Biodiesel” Applied Mechanics and materials Vol. 393 pp 344-349 August

2013. ISSN:16609336; Index: SCOPUS, H Index 9, Q4

20. Helmisyah Ahmad Jalaludin, Shahrir Abdullah, Mariyam Jameelah Ghazali, Bulan

Abdullah, Nik Rosli Abdullah,”Effect of Extreme Temperatures on Coated Piston

Crown for CNGDI Engine” Applied Mechanics and materials Vol. 393 pp 281-286

August 2013. ISSN:16609336; Index: SCOPUS, H Index 9, Q4

21. Wan Noaimadudin W.M. Kamal, Nor Hayati Saad, Amir Radzi Ab. Ghani, Nik Rosli

Abdullah, Khairul Izwandy Abd Jazam ”Modelling and Simulation of a Single Deck Bus

Subjected to Rollover Crash Loading” Applied Mechanics and materials Vol. 393 pp

453-459 August 2013; ISSN:16609336; Index: SCOPUS, H Index 9, Q4

22. Diyar I. Ahmed 1,S. Kasolang, Basim A. Khidhir, N.R. Abdullah,“Application of

Response Surface Methodology to Predict Oil-Film Friction in Journal Bearing”. Applied

Mechanics and materials Vol. 393 (2013) pp 881-887; ISSN:16609336; Index: SCOPUS,

H Index 9, Q4

23. Nik Rosli Abdullah, Nafis Syabil Shahruddin, Aman Mohd. Ihsan Mamat, Salmiah

Kasolang, Aminuddin Zulkifli and Rizalman Mamat.” Impacts of Air Intake Pressure to

the Fuel Economy and Exhaust Emissions on a Small SI Engine”. Procedia Engineering,

Vol 68. Pp 278-284, ISSN:1877-7058; Index: SCOPUS, H Index 7, Q3. IF = 0.496.

24. Syarifah Yunus, Amirul Rashid, Nik Rosli Abdullah, Rizalman Mamat, Syazuan

Latip.”Emissions of Transesterification Jatropha-Palm Blended Biodiesel”. Procedia

Engineering, Vol 68. Pp. 265-270, ISSN: 1877-7058; Index: SCOPUS, H Index 7, Q3. IF

= 0.496.

25. Helmisyah Ahamad Jalaludin, Shahrir Abdullah, Mariyam Jameelah Ghazali, Bulan

Abdullah and Nik Rosli Abdullah. “Experimental Study of Ceramic Coated Piston


Page 14

Crown for Compressed Natural Gas Direct Injection Engines”. Procedia Engineering, Vol

68. Pp 505-511, ISSN:1877-7058; Index: SCOPUS, H Index 7, Q3. IF = 0.496.

26. Syarifah Yunus, Amirul Abd. Rashid, Syazuan Abdul Latip, Nik Rosli Abdullah,

Mohamad Ali Ahamd and Abdul Hakim Abdullah. “Comparative Study of Used and

Unused Engine Oil (Perodua Genuine and Castrol Magnetic Oil) Based on Property

Analysis Basis”. Procedia Engineering, Vol 68, Pp 326-330, ISSN:1877-7058; Index:

SCOPUS, H Index 7, Q3. IF = 0.496.

27. M. Mazlan, Anizah Kalam, N.R Abdullah, Huck-Soo Loo, A.M.Mustafa Al Bakri, M.S.

Abdul Aziz, C.Y Khor, Mohammad Amizi, M.R. Mohd Sukhairi,” The Effect Of Gap

Between Plastic Leaded Chip Carrier (PLCC) Using Computational Fluid Dynamic

(CFD) Software, FLUENT “ Advances In Environmental Biology, 7(12) Dec 2013, pp:

3843-3849. ISSN:19950756; Index SCOPUS, H Index 8, Q4.

28. M. Mazlan, Anizah Kalam, N.R Abdullah, Huck-Soo Loo, A.M.Mustafa Al Bakri, M.S.

Abdul Aziz, C.Y Khor, Mohammad Amizi, M.R. Mohd Sukhairi,” Development Of

Nano-Material (Nano-Silver) In Electronic Components Application“ Advances In

Environmental Biology, 7(12) Dec 2013, pp:3850-3856. ISSN:19950756; Index

SCOPUS, H Index 8, Q4.

29. Shafiq Suhaimi, Rizalman Mamat, Abdul Adam Abdullah, Amir Aziz, Nik Rosli

Abdullah” Investigation of Intake Flow Rate and Swirl Motion of Sl Engine” Applied

Mechanics and Materials Vol 465, pp 409-417, 2013. ISSN:16609336; Index SCOPUS,

H Index 9, Q4.

30. OM Ali, R Mamat, NR Abdullah, AA Abdullah, “Effects of Blending Ethanol with Palm

Oil Methyl Esters on low Temperature Flow Properties and Fuel Characteristics.

International Journal of Advanced Science & Technology, Volume 59, 2013.

31. Nik Rosli Abdullah, Nafis Syabil Shahruddin, Rizalman Mamat, Aman Mohd. Ihsan

Mamat and Aminuddin Zulkifli. Effects of Air Intake Pressure On The Engine

Performance, Fuel Economy And Exhaust Emissions Of A Small Gasoline Engine.

Journal of Mechanical Engineering and Sciences (JMES) ISSN (Print): 2289-4659; e-

ISSN: 2231-8380; Volume 6, pp. 949-958, June 2014.

32. Obed M. Ali , Talal Yusaf , Rizalman Mamat , Nik R. Abdullah and Abdul Adam

Abdullah, Influence of Chemical Blends on Palm Oil Methyl Esters’ Cold Flow

Properties and Fuel Characteristics. Energies 2014, 7, pp. 4364-4380.

33. Akasyah M. Khathri, Rizalman Mamat, Amir Aziz, Azri Alias, Nik Rosli Abdullah,

One-Dimensional Simulation of the Combustion Process in an Engine Cylinder with

Ethanol. Applied Mechanics and Materials Vol. 660 (2014) pp 447-451.

34. Akasyah M. Kathri , Rizalman Mamat, Amir Aziz1, Azri Alias, Nik Rosli Abdullah,

Combustion Characteristic of a Diesel Engine Operating with Methanol as Alternative

Fuel, Applied Mechanics and Materials Vol. 660 (2014) pp 452-456.

http://scholar.google.com/citations?view_op=view_citation&hl=en&user=LuQA_vcAAAAJ&sortby=pubdate&citation_for_view=LuQA_vcAAAAJ:isC4tDSrTZIC

http://scholar.google.com/citations?view_op=view_citation&hl=en&user=LuQA_vcAAAAJ&sortby=pubdate&citation_for_view=LuQA_vcAAAAJ:isC4tDSrTZIC


Page 15

35. K. Md Isa, K. Osman, N. R. Abdullah, A. Mukhtar, N. F. Othman, "CFD Modelling of a

Fluidized Bed Gasifier; Effects of Drag Model and Bed Heights", Applied Mechanics and

Materials, Vol. 699 (Nov. 2014), pp. 730-735.

36. ZimanWang, Miroslaw L. Wyszynski, Hongming Xu, Nik Rosli Abdullah, Jakub

Piaszyk , Fuel injection and combustion study by the combination of mass flow rate and

heat release rate with single and multiple injection strategies, Fuel Processing

Technology Vol. 132 (2015) pp 118-132.

37. Obed M. Ali, Nik Rosli Abdullah, Rizalman Mamat and Abdul Adam Abdullah,

Comparison Of The Effect Of Different Alcohol Additives With Blended Fuel On Cyclic

Variation In Diesel Engine, Journal of Energy Procedia 2015.

38. Obed M. Ali, Rizalman Mamat, Nik R. Abdullah and Abdul Adam Abdullah, Analysis

of Blended Fuel Properties and Engine Cyclic Variations with Ethanol Additive, Journal

of Biobased Materials and Bioenergy Vol. 9, 1–7, 2015

39. Helmisyah Ahmad Jalaludi,, Affiq Fazreen Rosman, Nik Rosli Abdullah and Hanith

Iskandar, Investigation On Temperature Profiles Of Piston Using Low Cost Burner Rig.

ARPN Journal of Engineering and Applied Sciences, pp 331-336, Vol. 10, No. 1, January

2015.

40. M.H. Mat, N.H. Badrulhisam, A.Q. Hanafiah, N.R. Abdullah and A.M.I. Mamat,

Characteristics Of K3-Vei4 Engine Performance Using Swirl Generator, Air Intake Tank

And Exhaust Gas Recirculation Modification. International Journal of Automotive and

Mechanical Engineering (IJAME) ISSN: 2229-8649 (Print); ISSN: 2180-1606 (Online);

Volume 11, pp. 2484-2494, January-June 2015.

40. Obed M. Ali, Rizalman Mamat, Nik R. Abdullah and Abdul Adam Abdullah , Analysis

of Blended Fuel Properties and Engine Performance with Palm Biodiesel‐Diesel Blended.

Journal of Renewable Energy 86 (2015) pp 59-67.

41. Nik Rosli Abdullah, Zeno Michael, A.R. Asiah, A.J. Helmisyah and Shaari Buang ,

Effects Of Palm Oil Methyl Ester (POME) On Fuel Consumption And Exhaust

Emissions Of Diesel Engine Operating With Blended Fuel (Fossil Fuel + Jatropha Oil

Methyl Ester (JOME)), Journal Teknologi Volume 76, No 5 (2015) Pp 43-47.

42. Hazim Sharudin, Nik Rosli Abdullah, A. M. I. Mamat, Obed M. Ali, Rizalman Mamat,

An Overview of Spark Ignition Engine Operating On Lower-Higher Molecular Mass

Alcohol Blended Gasoline Fuels. Journal Teknologi Volume 76, No 5 (2015) Pp 101-

105.

43. Nik Rosli Abdullah, Hazimi Ismail, Zeno Michael, Asiah Ab Rahim, Hazim Sharudin,

Effects Of Air Intake Temperature On The Fuel Consumption And Exhaust Emissions Of

Natural Aspirated Gasoline Engine, Journal Teknologi Volume 76, No 9 (2015) Pp 25-

29


Page 16

44. Amalina Amir, Nor Hayati Saad, Azri Shahmi Ramli, Amirul Abd Rashid, Noriah

Yusoff, Nik Rosli Abdullah, Salmiah Kasolang, Ahmed Jaffar, Thermal And

Rheological Behavior Of Recycled Rubber/Natural Rubber Blends In Recycle Tire

Process, Journal Teknologi Volume 76, No 5 (2015) Pp 89-94

Publications under review (Journal)

1. Investigation on Heat Transfer Characteristics of ceramic coated piston crown for a

CNGDI Engines, Journal of Mechanical Engineering, UiTM Shah Alam.

2. Effects of Tallow Methyl Ester on exhaust Emissions of a modern Sequential parallel

Twin-Turbocharged V6 Common rail direct injection diesel engine, Journal of Archivum

Combustion.

3. Low Rank Coal for Gasification: Effects of Operating Conditions and Recommendations,

Journal of Renewable & Sustainable Energy.

4. Effects of Dieseline (Diesel+ Gasoline) blends to the fuel economy and exhaust

emissions of small diesel engine, International Journal of Automotive & Mechanical

Engineering (IJAME).

5. Fuel injection and combustion study by the combination of mass flow rate and heat

release rate with single and multiple injection strategies, Journal of Fuel.

6. Cycle-to-cycle variation in diesel engines powered by blended biodiesel-diesel fuel with

diethyl ether additive. Journal of Energy and Fuels.

7. Effects of Fuel Additive to the Fuel Economy and Emission in Gasoline Engine. Journal

of Technology.

8. Effect of Palm Oil Methyl Ester (POME) on Fuel Consumption and Exhaust Emissions

of Diesel Engine Operating with Blended Fuel (Fossil Fuel and JOME). Journal of

Technology.

9. An overview of spark ignition engine operating on lower-higher molecular mass alcohol

blended gasoline fuels. Journal of Technology.

10. Brake Specific Fuel Consumption CO Emissions on a 1.6L Gasoline Engine operates

with fuel additives and RON97. Journal of Technology.

11. Effects of Air Intake Temperature to the Fuel Consumption and Exhaust Emissions of

Natural Aspirated Gasoline Engine. Journal of Technology.

Selected Conference Papers

International:

1. A Jumaat, MH Ismail, N.R Abdullah “Effect Of Powder Loading On Metal Injection

Moulding (MiM) Green Properties” The Ninth Japan International Sample Symposium

Dec 2005.

2. W.A.Najmi W.N, N.R Abdullah “Combustion Characteristics For Palm Kernel Shells

Using An Inclined Grate Furnace” International Conference On Energy And

Environment 2006.


Page 17

3. N.R Abdullah, MH Ismail “Surface Roughness Identification Using Lamb Waves”

Asian Symposium On Materials And Processing 2006, Bangkok, 2006.

4. MH Ismail, N.R Abdullah “Densification Behaviour Of Incinerator Bottom Ash Using

Powder Compaction Method” Asian Symposium On Materials And Processing 2006,

Bangkok, 2006.

5. S Khushairi, N.R Abdullah “An Attempt To Convert Biomass Waste To Commercial

Product” - International Conference Of Advancement Of Materials And Nanotechnology

2007.

6. N.R. Abdullah, M.L. Wyszynski and A.Tsolakis “Soot emissions control using diesel

particulate filter and fuel-borne additives. Poster Presentation Organized by Graduate

School, University of Birmingham, December 2007.

7. N.R. Abdullah, M.L. Wyszynski and A.Tsolakis “Thermal Stress Analysis on Diesel

Particulate Filter Using CFD Modeling” Poster Presentation Organized by Graduate

School, University of Birmingham, April 2008.

8. N.R. Abdullah, M.L. Wyszynski and A.Tsolakis “Effects of Pilot Injection Timing on

Main Combustion Behaviour in Multi Cylinder V6 Diesel Engine” Poster Presentation

Organized by Graduate School, University of Birmingham, June 2009.

9. R. Mamat, N.R.Abdullah, H.M. Xu, M.L.WyszynskiA.Tsolakis, “Effect of Air Intake

Pressure Drop on Performance and Emissions of a Diesel Engine Operating with

Biodiesel and Ultra Low Sulphur Diesel (ULSD. International Conference on Renewable

Energy and Power QualityValencia, Spain., 15-17 April 2009.


“The Effect of Injection Pressure and Strategy in a Jaguar V6 Diesel Engine”. Journal of

KONES (Internal Combustion Engines, European Science Society of Power train and

Transport Publication). ISSN 1231-4005, Vol 16, pp 9-22. 2009.

11. R. Mamat, N.R.Abdullah, H.M. Xu, M.L.Wyszynski, A.Tsolakis, “Effect of Exhaust

Gas Recirculation (EGR) with Multiple Injections on Combustion Pattern in a Common

Rail Diesel Engine”. 12th EAEC European Automotive Congress 2009.


“Optimisation of Premixed Combustion on V6 Diesel Engine Through The Variation of

Pilot Injection Timings Combined with EGR”, United Kingdom-Malaysia Engineering

Conference, April 2010.

13. Rizalman Mamat, Nik Rosli Abdullah, HongmingXu, Miroslaw L. Wyszynski, A.

Tsolakis, ”Effect of Boost Temperature on the Performance and Emissions of a Common


Page 18

Rail Diesel Engine Operating with Rapeseed Methyl Ester (RME)”. World Congress on

Engineering, July 2010.

14. R.Mamat, N.R.Abdullah, N.Tamaldin, “Emissions of a single cylinder Diesel engine

operating with Ethanol”. 2nd

International Youth Science Festival, November 2010.

15. N.R Abdullah, D.Lui, T.Park, Hongming Xu, “Effect of Variations of Biodiesel Blends

on Engine Combustion and Emissions”. Poster presentation at University of Birmingham,

September 2011.

16. Ma’arof M.I.N, Ahamd I.N, Abdullah N.R, Karim S.A. Motorcycling Riding Issues:

Understanding the Phenomenon and Development of Ergonomics Intervention in

Improving Perceived Comfort for Prolonged Riding. iDECON 2012 – International

Conference on Design and Concurrent Engineering, 15-16 October 2012.

17. Nik Rosli Abdullah, Nafis Syabil Shahrudin, Rizalman Mamat, Aman Mohd. Ihsan,

Aminudin Zulkifli “Effects of Air Intake Pressure to The Engine Performance, Fuel

Economy and Exhaust Emissions a Small Gasoline Engine ”International On Conference

Mechanical Engineering Research July 2013.

18. Kamariah Md Isa, Kahar Osman, Nik Rosli Abdullah,Azfarizal Mukhtar,Nor Fadzilah

Othman. “CFD Modelling of a Fluidized Bed Gasifier; Effects of Drag Model and Bed

Heights” 3rd

International Conference and Exhibition on Sustainable Energy and

Advanced Materials, ICE-SEAM October 2013.

19. Characteristic of Blended Fuel Properties and Engine Cycle to Cycle Variations with

Butanol Additive. International Conference on Mathematics, Engineering & Industrial

Applications (ICoMEIA 2014).

20. Effects of Dieseline (Diesel+ Gasoline) blends to the fuel economy and exhaust

emissions of small diesel engine, International Conference on Automotive Innovation and

Green Energy Vehicle, AiGEV 2014.

21. Characterization of K3-Vei4 Engine performance Using swirl Generator, Air Intake Tank

and EGR Modification, International Conference on Automotive Innovation and Green

Energy Vehicle, AiGEV 2014.

IInntteerrnnaattiioonnaall CCoonnffeerreennccee IInnvvoollvveemmeenntt

No. Conference Name Role Venue Date

1 International conference on

renewable energy and power

quality

Co-Author Valencia, Spain 14-17 April

2009

2

12th EAEC European Automotive

Congress 2009

Co-Author Bratislava, Slovak

Republic

29 June – 1 July

2009


Page 19

3

Internal Combustion engines,

European Science Society of Power

Train and Transportation

Author &

Presenter

Zakopane, Poland 13-16

September 2009

44 United Kingdom-Malaysia

Engineering Conference

Author &

Presenter

University College

London, UK

8-9 April 2010

5

World congress on engineering Co-Author London, UK 30 June – 2 July

2010

6

XXI International Symposium on

Combustion Processes

Author &

Presenter

Miedzyzdroje,

Poland

14-17

September 2010

7

2nd International Youth Science

Festival

Co-Author Lviv, Ukraine 25-27

November 2011

8 3rd International Conference On

Mechanical and manufacturing

Engineering 2012 (ICME2012)

Co-Author Universiti Tun

Hussein Onn

Malaysia

20-21

November 2012

99 International Symposium on

Robotics and Intelligent Sensors

(IRIS2012)

Co-Author Kuching, Sarawak,

Malaysia

4 – 6 Sept 2012

10 International Conference on

Mechanical Engineering Research

2013

Author &

Presenter

Gambang, Pahang

Malaysia

1-3 July 2013

11 Procedings of the International

Conference on Advances in

Mechanical Engineering

ICAME2013

Author &

Poster

Melaka, Malaysia 28-29 Aug 2013

12 International conference on design

and concurrent engineering

Author &

Presenter

Melaka, Malaysia 30-31 October

2013

13 Malaysian International Tribology

Conference MITC2013

Author &

Presenter

Kota Kinabalu 18-20 Nov 2013

14 2nd

Colloqium on Teaching and

Learning

Author &

Presenter

Kota Bharu,

Kelantan

3-5 Jun 2014

15 2nd

Colloqium on Teaching and

Learning

Chair

Session

Kota Bharu,

Kelantan

3-5 Jun 2014

16 1st International Conference on

Automotiv & Green Energy

Vehicle (AiGEV 2014)

Author Kuantan, Pahang 26-27 Aug 2014

17 7th International Conference on

Applied Energy

Author &

Presenter

Abu Dhabi, UAE. 28-31 March,

2015


Advances in Mechanical

Engineering (ICAME 2015)

Author &

Presenter

Patrajasa, Bali

Indonesia

26-27 Aug 2015

19 6th International Conference On

Mechanical And Manufacturing

Engineering 2015 (Icme2015)

Author &

Presenter

Putrajaya, Malaysia 12-13Sept 2015

20 Malaysia International Tribology Author & Penang, Malaysia 16-17 Nov 2015


Page 20

Conference (MITC 2015) Presenter

21 3rd International Conference On

Recent Advances In Automotive

Engineering & Mobility Research

(ReCar) 2015

Author &

Presenter

Melaka, Malaysia 1-3 Dec 2015

CCoonnffeerreennccee OOrrggaanniizzeerr// CCoommmmiitttteeee MMeemmbbeerrss

No. Conference Name Role/ Level Venue Date

1 International Conference on


Engineering ICAME2013

Head of

Technical

Committe

Melaka, Malaysia 28-29 Aug 2013


Conference MITC 2013

Member of

Technical

Committee

Kota Kinabalu,

Sabah, Malaysia

18-20 Nov 2013

3

7th Global Economic Symposium ,

Kuala Lumpur.

Member of

Technical

Committee

Kuala Lumpur,

Malaysia

6-8 August 2014

4 International Symposium for

Technology and Sustainability

Member of

Technical

Committee

Shah Alam,

Malaysia

September 2015



Engineering (ICAME 2015).

Head of

Technical

Committe

Patra Jasa Bali

Resort & Villas,

Indonesia

26-27 August

2015


Conference 2015 (MITC2015).

Member of

Technical

Committee

Penang, Malaysia 16 ~ 17

November 2015.

7 International Symposium on

Technology for Sustainability

Member of

Committee

UiTM, Shah

Alam.

4-6 August 2015

G: CONSULTATION/WORK IN INDUSTRY

1) Curriculum Review for Diploma in Automotive Engineering with Kuala Lumpur

Infrastructure University College (KLUIC),MALAYSIA Year 2005.

2) The Provision of Lab facilities and Trainers for 3D CAD Solid Edge Fundamental Course

for The F1 in School Programme. MALAYSIA Year 2007.

3) Research Fellow at University of Birmingam and Jaguar Land Rover UK, Year 2011.


Page 21

4) Working Group on Hydaulic Turbines with SIRIM Sdn. Bhd. Shah Alam, Selangor-

2012.

5) Working Group on Passive Safety with SIRIM Sdn. Bhd. Shah Alam, Selangor – 2013.

6) Eddy Current Dynamometer Installation for Internal Combustion Engine with Hakita

Engineering Sdn. Bhd. - 2013.

7) Combustion in Fluent with Universiti Teknologi Malaysia, UTM – June 2013.

8) Eddy Current Dynamometer Installation for Internal Combustion Engine with Hakita

Engineering Sdn. Bhd. – 2014.

9) Programme High Centre of Excellent (i-COE),Module on Engine Development And

Testing, July 2014.

10) Programme High Centre of Excellent (i-COE), Module on Computational Fluid

Dynamics, July 2014.

11) Engine Testing on Fuel Additives, August 2015. Perfect Triangle.

H: COMMITTEE & CONSULTATION/WORK IN UNIVERSITY

1. Deputy Dean (Academic): Year Jan 2012 – Present.

2. Head of Accreditation Committee Faculty of Mechanical Engineering: Year 2012-2014

3. Head of Curriculum Review Faculty of Mechanical Engineering: Year 2012-2014

4. Head of Outcome Based Education (OBE) Faculty of Mechanical Engineering: Year

2012-2014.

5. Committee of Vice Chancellor Quality Award: Year 2012-2014.

6. Acting Deputy Dean (Academic): 15 Sept 2011-31 Dec 2011.

7. Head Centre of Studies (Thermo-fluids):10 August 2011 – 14 Sept 2011.

8. Post Doctorial at University of Birmingham and Jaguar UK, Nov 2010-August 2011.

9. Head of Program, Bachelor in Mechanical Engineering: Year 2005-2007.

10. Committee of Vice Chancellor Quality Award: Year 2006-2007.

11. Head of Automotive, FKM, UiTM: Year 2005 - 2007.

12. Member of Curriculum Review EM220 and EM221 FKM, UiTM: Year 2005- 2007.

13. Member of Curriculum Review EM110 FKM, UiTM: Year 2006.

14. Member of Program AccreditationEM220: Year 2005-2007.

15. Head of Internal Audit System Committee, FKM, UiTM: Year 2004 - 2005.

16. Fasilitator for Program Kepimpinan & Pembangunan Pelajar, FKM, UiTM (2005 -

present)

17. Technical Committee - National Conference on Advances in Mechanical Engineering

Applications: 18-20 Mei 2005 (2004/2005).

18. Badminton Player, 'Piala ISO Kejuruteraan '(2004).


Page 22

19. Badminton Player, Kejohanan Badminton antara bahagian, UiTM(2005).

20. Member of Pasukan Kerja Pensijilan Audit PeringkatUiTM (2004).

21. Member of Research, Development & Commercialization Unit, FKM (2003 - 2004).

I: FUNDED RESEARCHES (GRANTS)

Current Researches

No Research Project Source Total Funds Begin

Year

End

Year

1

Transferring to Asia Green recycle in

Formulating and Testing Products of

Recycled Tire: A Generation of Green

Factory and Income

KTP RM138,580.00 2013 2015

2

Waste Heat Exchanger Of Organic

Rankine Cycle (ORC) For Engine

Energy Recovery In Internal

Combustion Engine

ERGS RM59,850 2013 2016

3

Heat transfer mechanisme on coated

piston crown for spark ignition

engine.

RAGS RM65,000.00 2013 2016

4

Flow characterization

through acoustic signal

processing in a Ranque Hilsch

vortex tube

FRGS 97,200.00 2014 2016

5

Characterization of Palm Oil Methyl

Ester (POME) blended biodiesel on

performance and exhaust emission of

CI Engine.

RAGS 71,000.00 2014 2016

6

Effects of energy recovery methods to

the efficiency of a hydrogen

propulsion system

FRGS 138,200.00 2014 2016

Total Grant

Completed Researches

No Research Project Total Funds Begin

Year

End

Year

1 Application of Lamb Waves in Wear Detection

on Aluminium Plate. Short Term Grant (BRC

Grant): Rujukan IRDC: 600-IRDC/ST/5/3/959

RM20,000.00 2004 2006


Page 23

2

Development of A Dual-Mode Fixed Bed

Combustion Chamber For Solid Waste Fuels.

Short Term Grant (BRC Grant) :

Rujukan IRDC: 600-IRDC/ST/5/3/947

RM20,000.00 2005 2007

3

The Design and Development Of A Turbojet

Combustion Equipped With Turbulence Chamber

As Thrust Booster. Short Term Grant (BRC

Grant)

RM26,000.00 2006 2008

4

Flex-diesel Engines with Sustainable Bio-fuels

for Clean and Efficient On- and Off-Road

Vehicles. University of Birmingham, UK.

September 2011.

GBP 1.2

million

(UK Grant)

2007 2011

5

FRGS: Jatropha-Palm Blends as Biodiesel Fuel

For Internal Combustion Engine: A Development

on Blending Process and Analysis of

Performance, Emission and Lubricity.

RM80,000.00 2011 2012

6

FRGS: Computational Analysis on Thermal

Stress in Diesel Particulate Filter During Soot

Loading and Regeneration.

RM128,000.00 2011 2014

7

FRGS: Combustion Characteristic of Emulsified

Biodiesel with Hydrogen Injection on Diesel

Engine.

RM75,200.00 2012 2014

8 FRGS: Hydrodynamic Fluid Behaviour of Bio-

Lubricants In Pain Bearings. RM80,000.00 2012 2015

9

DANA: Energy Storage Performance Of

Stabilized Phase Change Materials

(PCM)/Thermoplastic Composites

RM32,000.00 2012 2014

10 FRGS: Jatropha-Waste cooking oil biodiesel wear

properties. RM87,000.00 2013 2015

11

DANA: Thermal Analysis on Thermal Barrier

Coated Piston Crown For Compressed Natural

Gas Direct Injection Engine.

RM32,000.00 2012 2014


Page 24

J: POST GRADUATE SUPERVISION

Postgraduate (PhD)

NNoo.. NNaammee ooff SSttuuddeennttss TThheessiiss// RReesseeaarrcchh TTiittllee

YYeeaarr

11 Obed Majeed Ali

PMM12001

Engine Testing On Bio-Diesel Blend with

Small Portion of Additive For Performance

Improvement.

Completed

22 Mazlan Mohamed

2010110839

The development of nanotechnology in

plastic leaded chip carrier (PLCC) using

Nano-Material, Nano silver.

2013 -

Present

33 Kamariah Binti Md Isa

PMM123112

Optimization of operating conditions for

fluidized bed gasifier.

2013-

Present

Postgraduate (Master)


YYeeaarr

11 Mohd Yusri Mokhtar

2011169899

Reliability Analysis on Allison T56

Turboprop Engine

Completed

22 Hazim Bin Sharudin

2012454158

The Effect Of Iso-Butanol Additive In

Methanol-Gasoline Blends On Engine

Performance And Exhaust Emission Using

Spark Ignition Engine.

2014 -

Present

33 Shahrizal Bin Umar

201393319

Effects of engine oil type to the performance

and emissions of diesel engine.

2014 -

Present

44 Najmi Haziq Bin

Badrulhisam

2014319907

Effects of oxygenates fuels to the engine

performance and emissions

2015-

Present

55 Ammar Bin Ismail @

Mukhtar

2014666796

Effects of Mineral and Fully Synthetic Oil to

the Fuel and Engine Durability

2015-

Present

66 Ahmad Azli Sahran

2014186431

The effect of new formulation lube oil to the

turbine performance

2015-

Present


Page 25

K: UNDER GRADUATE SUPERVISION


YYeeaarr

11 Mohamad Shakban Jamaludin

2006200096

Ocean Wave Energy Converter System 2011

22 Mohd Syazni MohdNizam

2008407352

The Effects of Exhaust Size to the

Engine Performance and Fuel Economy

On1.3L Gasoline Engine

2012

33 Mohd Farouq Baharin

2008299918

The Effect of Nozzle Injector Position

To the Engine Performance And Fuel

Economy On 1.3L Gasoline Engine

22001122

44 Muhammad Hafiz Zakaria

2008407512

The Effect of Radiator Size To the

Engine Performance And Fuel Economy

On 1.3L Gasoline Engine

22001122

55 Arez Athari Hamdan

2008407368

The Effect of Air Intake Temperature to

the Engine Performance And Fuel

Economy On MYVI 1.3L Gasoline

Engine

22001122

66 Wan Nazirul Wan Ahmad

2009237082

The Effect of Thermostat Temperature

Setting To the Engine Performance and

Fuel Consumption On 1.3L Gasoline

Engine

22001122

77 Abdul Muiz Ahmad Adzmi

2009475094

The Effect of Air Intake Flow-rate to

The Engine Performance and Fuel

Consumption On 1.3L Gasoline Engine

22001122

88 Fitri Azhar Mohamad

2009812936

Research Title “Effect of Spark Plug

Gap to The Engine Performance And

Fuel Consumption On 1.3L Gasoline

Engine

22001122

99 Muhamad Faisal Bin Mamat @

Omar

2010855716

Research Title “The Effect of Cooling

System to the Engine Performance, Fuel

Consumption And Exhaust Emissions

22001133

1100 Wan Fakhrullah Adam

2010687674

Research Title” Effects of Exhaust

System to the Engine Performance, fuel

Consumption and Exhaust Emissions.

22001133


Page 26

1111 Wan Norhisyam Bin Wan

Mohamad

2009621406

The Effects of Air-Conditioning System

to the Engine Performance, Fuel

Consumption and Emissions on 1.6L

Campro Gasoline Engine

22001133

1122

Muhamad Hasan Basri Bin Zakaria

2009678942

Effects of Biodiesel Blend (B20) to the

Engine Performance, Fuel Consumption

and Exhaust Emissions of Diesel Engine

22001133

1133 Johari Bin Njompa

2009686212

The Effect of Firing Order to the Engine

Performance And Emission

22001133

1144 Muhammad Fathi Zakaria

2010418432

A Temperature Distribution inside the

Engine Compartment of 1.6L Gasoline

Engine

22001133

1155 Norman Bin Mohd Sarip

2009826642

Engine Performance and Emissions of a

Single Cylinder Diesel Engine Fuelled

With Biodiesel Blends Palm Oil Methyl

Ester (POME)

22001133

1166 Aminuddin Bin Zulkifli

2009456602

The effect of air intake pressure to the

engine performance and emission on

campro 1.6L Gasoline Engine”

22001144

1177 Muhd Nazmi Akmal Bin Muhd

Rafee

2009226666

The effects of Dieseline (Diesel +

Gasoline) Blends to the engine

performance and emissions

22001144

1188 MMuuhhaammmmaadd HHaaffiizz AAhhmmaadd ZZuubbiirr

22001100449911119966 Effects of fuel additive to the engine

performance and emission of

compression ignition engine

2014

1199 Mohd Hilmi rashid

22001100226666889922 DDeetteeccttiioonn ooff mmiissffiirree bbyy uussiinngg eexxhhaauusstt

tteemmppeerraattuurree pprrooffiillee..

2014

2200 MMuuhhaammmmaadd MMuussttaaqqiimm RRaazzaallii

22001100443344441144

TThhee eeffffeeccttss ooff EExxhhaauusstt GGaass

RReecciirrccuullaattiioonn oonn eennggiinnee ppeerrffoorrmmaannccee

aanndd ffuueell ccoonnssuummppttiioonn aanndd eemmiissssiioonnss

2014

2211 Mohd Syukri Khosim

22001111226699112266 TThhee eeffffeeccttss ooff aaiirr iinnttaakkee tteemmppeerraattuurree ttoo

eennggiinnee ppeerrffoorrmmaannccee,, ffuueell ccoonnssuummppttiioonn

aanndd eemmiissssiioonnss oonn SSppaarrkk IIggnniittiioonn EEnnggiinnee..

2014

2222 MMuuhhaammmmaadd RRaaffiiddii AAbbdd RRaahhmmaann

22001111881177551122

CCoommbbuussttiioonn bbeehhaavviioouurr ooff SSppaarrkk IIggnniittiioonn

eennggiinnee aatt vvaarriittiioonn ooff eennggiinnee ssppeeeedd aanndd

2014


Page 27

llooaadd ffuueelllleedd wwiitthh ggaassoolliinnee..

2233 Al-Sha'ari Bin Buang

22001100335566885599 EEffffeeccttss ooff bbiioobbaasseedd ssyynntthheettiicc ffuueell ttoo tthhee

ffuueell ccoonnssuummppttiioonn aanndd eexxhhaauusstt eemmiissssiioonnss

ooff ssiinnggllee ccyylliinnddeerr ffoouurr ssttrrookkeess ddiieesseell

eennggiinnee

2015

2244 MMoohhdd KKhhaaiirruull AAnnuuaarr

22001111665533995566

EEffffeeccttss ooff bbiioobbaasseedd ssyynntthheettiicc ffuueell ttoo tthhee

ffuueell ccoonnssuummppttiioonn aanndd eemmiissssiioonnss ooff

ggaassoolliinnee eennggiinnee

2015

2255 MMoohhdd IIzzhhaamm BBiinn WWaahhaabb

22001111220011227766

CCoommbbuussttiioonn cchhaarraacctteerriissttiiccss aanndd eennggiinnee

eemmiissssiioonnss ooff ddiieesseell eennggiinnee ffuueelllleedd wwiitthh

hheeaatteedd bbiiooddiieesseell--ddiieesseell bblleennddss..

2015

2266 MMuuhhaammmmaadd SSyyaaffiiqq BBiinn SSuuhhaaiimmii

22001111664444774488

EEffffeecctt ooff aaiirr hhuummiiddiittyy ttoo tthhee ffuueell

ccoonnssuummppttiioonn aanndd eexxhhaauusstt eemmiissssiioonnss ooff

nnaattuurraall aassppiirraatteedd ggaassoolliinnee eennggiinnee..

2015

2277 CChhee AAzzllyy IIzzzzaatt AAmmiirr BBiinn CChhee

WWiissllyy

22001111661144444444

EEffffeecctt ooff ffuueell aaddddiittiivvee oonn ccoommbbuussttiioonn

bbeehhaavviioouurr aanndd eemmiissssiioonnss ooff ddiieesseell

eennggiinnee..

2015

2288 RRaa’’ffaatt WWaajjddyy BBiinn MMuuhhaammmmaadd

22001111665511330088

EEffffeeccttss ooff EExxhhaauusstt GGaass RReecciirrccuullaattiioonn

((EEGGRR)) ttoo tthhee EEnnggiinnee PPeerrffoorrmmaannccee aanndd

EEmmiissssiioonnss

2015

2299 MMoohhdd IIzzhhaann BBiinn WWaahhaabb

22001111220011227766

CCoommbbuussttiioonn aanndd eemmiissssiioonnss

cchhaarraacctteerriissttiiccss ooff ddiieesseell eennggiinnee ffuueelleedd

wwiitthh hheeaatteedd bbiiooddiieesseell

2015

3300 MMuuhhaammmmaadd SSyyaaffiiqq BBiinn SSuuhhaaiimmii

22001111664444774488

EEffffeeccttss ooff aaiirr hhuummiiddyy ttoo ffuueell eeccoonnoommyy

aanndd eennggiinnee eemmiissssiioonnss ooff nnaattuurraall

aassppiirraatteedd ggaassoolliinnee eennggiinnee

2015

3311 RRaaffaatt WWaajjddyy BBiinn MMuuhhaammmmaadd

22001111665511330088

EEffffeeccttss ooff EEGGRR rraattee ttoo tthhee eennggiinnee

ppeerrffoorrmmaannccee aanndd eennggiinnee eemmiissssiioonnss

2015

3322 CChhee AAzzllyy IIzzzzaatt AAmmiirr BBiinn CChhee

WWiissllyy

22001111661144444444

EEffffeeccttss ooff ffuueell aaddddiittiivveess ttoo tthhee eennggiinnee

ppeerrffoorrmmaannccee aanndd eennggiinnee eemmiissssiioonnss ooff

ddiieesseell eennggiinneess

2015

3333 MMuuhhaammmmaadd SSyyaarriiffuuddddiinn MMoohhaammeedd

ZZaahhaarriinn

22001111882211113322

EEffffeeccttss ooff EEtthhaannooll oonn eennggiinnee

ppeerrffoorrmmaannccee aanndd eemmiissssiioonnss ooff ggaassoolliinnee

eennggiinneess

2015

3344 AAhhmmaadd ZZaakkuuaann BBiinn AAzzmmaann

22000088440000998888

EEffffeeccttss ooff bbiiooddiieesseell bblleennddss ttoo tthhee eennggiinnee

ppeerrffoorrmmaannccee aanndd eemmiissssiioonnss ooff DDiieesseell

EEnnggiinnee

2015


Page 28

3355 HHiizzhhaarr HHaaiiddhhaarr BBiinn HHaammddaann

22001111778877886655

EEffffeecctt ooff vvoollttaaggee ssttaabbiilliizzeerr ttoo tthhee eennggiinnee

ppeerrffoorrmmaannccee aanndd eemmiissssiioonn ooff mmuullttii

ccyylliinnddeerr ddiirreecctt iinnjjeeccttiioonn ggaassoolliinnee eennggiinnee

2015

Potential Title for Bachelor Student

1. Effects of Alternative fuel to the engine performance and fuel economy on Gasoline

Engines.

2. Emission control On Gasoline/Diesel Engines through Combustion Strategies.

3. Study The Correlation Between Exhaust Gas Temperatures With Misfire On

Gasoline/Diesel Engines.

4. The Effect of a Firing Order to The Engine Performance, Fuel Economy And Emissions.

5. Study on Variable Geometry Turbocharger on High Speed Direct Injection Diesel

Engine.

6. Study on Injection Strategies, Combustion Stability and Emission Characteristics in a

Direct Injection Diesel Engine.

7. Investigate on Cooled EGR and Hot EGR to The Engine Performance And Emissions.

8. Heat Recovery Systems For Passengers Vehicles.

9. Researches On Advanced Air-fuel Mixture Formation Through Novel Air Intake System

For Gasoline/DieselEngines.

10. Future Alternative And Additives Fuels For Gasoline And Diesel Engines To Balance

Engine Performance, Fuel Economy And Emissions.

11. The Effect of Air Intake System to The Engine Performance And Emissions On Multi-

Cylinder Gasoline Engine.

12. Effects of Hydrogen Fuel to The Engine Performance, Fuel Economy And Exhaust

Emissions On Gasoline Engine.

L: SPECIAL INVITATIONS/APPOINTMENTS/ EXPERTISE

CONTRIBUTIONS

1. Head of Logistics ICAME 2015, 26-27 Aug, Bali Indonesia.

2. Co-Chair Person, ICAME2015, 26-27 Aug Bali, Indonesia.

3. Viva Chairperson UiTM,16 Oct 2015.

4. Invited Speaker: Workshop on Teaching and Learning Methods, 21 Aug 2015, Universiti

Malaysia Pahang, Pekan Pahang.

5. International Judge for International Invention, Innovation and Technology Exhibition

(ITEX) 2015, 21 May 2015, Kuala Lumpur Convention Centre.

6. External Examiner for Master Student from RMIT University, Australia, February 2015.

7. External Examiner for Master Student from University of Malaya, Optimization of

Alcohol – Gasoline Blended Fuel, Dec 2014.


Page 29

8. Internal Examiner for Master Student , Investigation of Newly Develop Swirl

Effervescent Atomization Using Photograpic-Based Technique, Dec 2014.

9. Invited Speaker for Career Road Map Programme 13-18 April 2014 organized by

Sekolah Menengah Sains Machang, Kelantan.

10. Internal Auditor for UiTM 2014.

11. Fasilitator on Examination Paper Workshop, UiTM, 2014.

12. Fasilitator on AIMS for Academic Management, 2014.

13. Fasilitator Soft Skills Training, UiTM Shah Alam, 2014.

14. Invited Speaker : Student Development and Leadership Programme,”Networking”,

UiTM, 2014.

15. Invited Speaker : OBE Implementation at Campus Pasir Gudang, Johor. September

2014.

16. Judge for Internal Speak Out for Engineering Competition 2014.

17. National panel of judges: IID Innovation Competition 2014, UiTM Johor, Malaysia

18. Programme and Study Advisory committee for Diploma of Engineering in Automotive

Maintainance at Universiti Kuala Lumpur Malaysia France Institute (UniKL MFI), 2014-

2016

19. International Judge for International Invention, Innovation and Technology Exhibition

(ITEX) 2014, 8 May 2014, Kuala Lumpur Convention Centre.

20. National panel of judges: SIDC 2013, UiTM Puncak Alam Selangor, Malaysia

21. Invited Speaker : Student Development and Leadership Programme,”Hubungan Etnik”,

UiTM, 2013

22. National panel of judges: IID Innovation Competition 2013, UiTM Johor, Malaysia

23. External Evaluator Panel for Postgraduate Research Proposal, Universiti Malaysia

Pahang, Jun 2013.

24. Evaluator Panel Dynamometer Installlation, Hakita Engineering Sdn. Bhd. May 2013.

25. Fasilitator on Examination Paper Workshop, UiTM, May 2013-06-21

26. Evaluator Panel for Modul Development Training in Learning and Teaching in Higher

Education, AKEPT, Feb 2013.

27. Fasilitator on OBE Workshop, Faculty of Mechanical Engineering, UiTM, Feb 2013.

28. Fasilitator Soft Skills Training, UiTM Shah Alam, 2011- Present

29. Invited Speaker : Student Development and Leadership Programme,”1 Malaysia”, UiTM,

2012.

30. Invited Speaker : Student Development and Leadership Programme,”Hubungan Etnik”,

UiTM, 2012.

31. Evaluator Panel for Modul Training of Trainers (TOT) on Project Oriented Problem-

Based Learning (POBL), AKEPT, Oct 2013.

32. Invited Speakers: OBE Implementation on Engineering Courses, UiTM Perlis, 29

October -1 November 2012,Pulau Langkawi, Kedah Malaysia.

33. National panel of judges: IID Innovation Competition 2012, UiTM Johor, Malaysia.

34. Invited Speakers : Malaysia-Japan International Institute of Technology (MJIIT),

Universiti Teknologi Malaysia (UTM) 27-28 Aug. 2012 in Kuala Lumpur, Malaysia at

UTM Kuala Lumpur

35. Invited Speaker : Vehicle Technology Research Group, University of Birmingham, UK.

March 2011.


Page 30

M: PAPER REVIEWER (NATIONAL/INTERNATIONAL)

1. International Conference on Advances in Mechanical Engineering (ICAME 2015)

2. International Journal of Mechanical Engineering, 2014.

3. Journal of Environment and Waste Management, 2014.

4. Journal of Renewable and Sustainable Energy (jrse.aip.org) (2012,2013 and 2014)

5. IEEE Colloquium on Humanities, Science and Engineering Research, CHUSER 2014

6. Journal of Energy 2014.

7. International Conference on Automotive Innonvation and Green Energy Vehicle AiGEV

2014.

8. Malaysian International Tribology Conference 2013.

9. International Conference on Advances in Mechanical Engineering (ICAME 2013)

10. International Conference on Advances in Mechanical Engineering (ICMER 2013)

11. Journal of Renewable and Sustainable Energy (jrse.aip.org) (2013).

12. IEEE Business Engineering and Industrial Applications Colloquium, BEIAC 2013.

13. Malaysian International Tribology Conference 2013 (MITC2013).

14. 3rd Malaysian Postgraduate Conference (MPC2013).

15. International Journal of Automotive and Mechanical Engineering (IJAME).

16. Journal of Renewable and Sustainable Energy (jrse.aip.org) (2013).

17. 2nd International Symposium on Robotics and Intelligent Sensors 2012 (IRIS2012).

18. Journal of Mechanical Engineering, UiTM Shah Alam. 2012 - Present

N: INOVATION/ INVENTION/ DESIGN

1. Silver Award Winner – An International Innovation, Design and Conference Kuala

Trengganu, October 2014

2. Bronze Medal – Pencipta 2013, 7-9 Nov 2013 Kuala Lumpur Convention Centre.

3. Gold Medal- IID Innovation Platform 2012 UiTM Kedah and UiTM Pulau Pinang

4. Silver Medal – IID Innovation Competition 2012 FKM, UiTM Shah Alam.

5. Bronze Medal – IID Innovation Competition 2012 FKM, UiTM Shah Alam.

6. Vice Chancellor’s Quality Award – Faculty Champion (Committe Member) 2012

7. Vice Chancellor’s Quality Award – Faculty Champion (Committe Member) 2011

8. Excellent Service Award (Anugerah Perkhidmatan Cemerlang UiTM) Year 2005

O: SELECTED STAFF DEVELOPMENT AND TRAINING

1. Training of Trainers for Academic Module, November 2014.

2. Workshop on Accreditation Assessment, November 2014.

3. Training of Master Trainers (TOMT) for Soft Skills Student Development, April 2014.

4. Conference of Heads of Academic Department of UiTM (CHAD 2013), December 2013.

5. Effective Influencing Skills in Dealing with Difficult People and Situations, Knowledge

Paragon Sdn. Bhd. 9-10 October 2013.

6. External Review Training, InQKA Universiti Teknologi MARA, UiTM, 17-18

September 2013.


Page 31

7. Thinking Out of The Box, The Training Hub (M) Sdn. Bhd, May 2013.

8. Academic Workshop, UiTM, May 2013.

9. Leadership Development Training In Learning And Teaching In Higher Education:

Understanding Learning Basic Level, AKEPT, Feb 2013.

10. 2-Day Course On The Legend Of Success: The Power Of Thinking Big and Going

Beyond – Emerge Sdn. Bhd., Feb 2013

11. Curriculum Review Workshop, UiTM, December 2012.

12. Academic Workshop, UiTM, December 2012

13. Professional Talk Understanding Industry Needs For Students Employability, Faculty Of

Mechanical Engineering, UiTM, November 2012.

14. Stress Management, Faculty of Mechanical Engineering, UiTM,November2012

15. The Legend of Success: 10 Hot Skills to be Mastered for Great Leaders, Head of

Departments and Managers. Emerge Knowledge Connection Sbn. Bhd., October 2012

16. Responsibility of Academic Resource Person, UiTM, September 2012

17. Program Executive Talk: Best Teaching Practices In Engineering Education, ILQAM

UiTM, June 2012

18. One Day Workshop On Outcomes Based Education (OBE) and Preparing Exam Question

Per Blooms' Taxonomy, IEM Malaysia, June 2012

19. Route to Charter Engineer & Colloquium, Faculty of Mechanical Engineering UiTM,

May 2012.

20. Examination Management, UiTM, March 2012.

21. Universal Test Rig (Data Pro Control System), Hakita Engineering Sdn. Bhd. March

2012.

22. Academic Workshop, UiTM, December 2011.

23. Leadership Management II, AKEPT, December 2011.

24. Academic Transformation, UiTM, September 2011.

25. The Quran as a Foundation of Intellectual Culture: An Oxford Perspective, CITU UiTM,

August 2011


Page 32

P: REFERENCES

1. Professor Ir Dr Hj Ahmed Jaffar

Dean

Faculty of Mechanical Engineering,

Universiti Teknologi MARA

40450 Shah Alam, Selangor, MALAYSIA

Tel.: +603 5543 5161

Fax: +603 5543 5160

E-mail: [email protected]

2. Professor Ir. Dr. Mohamad Nor Berhan.

Professor, Faculty of Mechanical Engineering,

Universiti Teknologi MARA

40450 Shah Alam, Selangor, MALAYSIA

Tel.: +603 5543 5161

E-mail:berhan @salam.uitm.edu.my

3. Professor Miroslaw Wyszynski

Professor of Novel Vehicle Technology

School of Merchanical Engineering

University of Birmingham

Edgbaston

Birmingham

B15 2TT

UK

Tel. +44 (0)121 414 4159

E-mail:[email protected]




Documents

Nik rosli Abdullah 2012 - Universiti Teknologi MARA · PDF fileDr. Nik Rosli Abdullah is also registered with Board of Engineers Malaysia ... Universiti Teknologi MARA ... Contract