Upload
augusto-manuel-inga-sanchez
View
220
Download
0
Embed Size (px)
Citation preview
7/23/2019 Mercedes Benz i e Ltr (1)q
http://slidepdf.com/reader/full/mercedes-benz-i-e-ltr-1q 1/6
Classic Car Series : 04
AssemblyInstructions
Mountain fold
Valley fold
Cut a notchalong this line.
Cut a notchalong the line.
Dotted line
Dashed and
dotted line
Solid line
Scissors mark
Fold so that the printed pattern faces outside. Dots indicate parts to be glued;
dotted lines indicate approximate area for
application of glue.
Glue parts with the same number together.
Glue areas within the same part together.
Glue to the reverse side of the specified part.
Fold so that the printed pattern faces inside.
Cut along the center of the line.
Red dot
Green dot
Blue dotCut these areas out.
Glue, scissors and other tools may be dangerousto young children so be sure to keep them out ofthe reach of young children.
Assembly Instructions : Six US letter sheets (No.1 to No. 6)Build this model with careful reference to the Assembly Instructions.
Tools Assembly tip
Key to symbols
Write the number of each part on the reverse side of the part in pencil uponcutting it out, to be sure you can tell which part is which later.Before gluing, crease the paper along mountain and valley fold lines. Tracealong the folds with a ruler and an exhausted ballpoint pen (out of ink) to get asharper fold.Make sure rounded sections are nice and stiff.
ScissorsRuler, Set squareGlue (Wood glue or craft glue recommend)Exhausted ballpoint pen (out of ink)Toothpicks (for use in applying glue)Tweezers (useful for handling small parts)Pencil
View of completed model * This model was designed for Papercraft and may differ from the original in some respects.
Mercedes Benz500K
7/23/2019 Mercedes Benz i e Ltr (1)q
http://slidepdf.com/reader/full/mercedes-benz-i-e-ltr-1q 2/6
Carefully shape curves.
Do not glue here.
Shaded areas in diagrams indicate reverse side of parts.
Do notglue here.
Carefully shape curves.
Carefully shape curves.
Affix with glue.
Affix with glue.
Affix with glue.
Mercedes Benz 500K Assembly
Instructions
7/23/2019 Mercedes Benz i e Ltr (1)q
http://slidepdf.com/reader/full/mercedes-benz-i-e-ltr-1q 3/6
Carefully shape curves.
Align fold linesand flaps and
glue together.
Shaded areas in diagrams indicate reverseside of parts.
Mercedes Benz 500K Assembly
Instructions
7/23/2019 Mercedes Benz i e Ltr (1)q
http://slidepdf.com/reader/full/mercedes-benz-i-e-ltr-1q 4/6
*Note different numbers for left and right parts.*Diagram is R.
*Note different numbers for left and r ight parts.*Diagram is R.
Carefully shape curves.
Carefully shape curves.
*Right side
*Left side
Shaded areas in diagrams indicate reverse side of parts.
Mercedes Benz 500K Assembly
Instructions
7/23/2019 Mercedes Benz i e Ltr (1)q
http://slidepdf.com/reader/full/mercedes-benz-i-e-ltr-1q 5/6
*Note different numbers for left and right parts.*Diagram is R.
Carefully shape curves.
Carefully shapecurves.
Confirm top/bottom before gluing.
Carefully shape curves.
Pay attention to the directionof gluing.
Carefully shape curves.
Viewed from above
Front
Confirm top/bottom before gluing.
Affix with glue.
Affix with glue.
Affix with glue.
*The numbers inside the parentheses are given to theparts for lights with a small center.
toptop
*Right side
*Left side
Fold it in half, and catch the pasting margin of Part 52 and glue.*Pay attention because the part numbers of the left and right are different.
Shaded areas in diagrams indicate reverse side of parts.
Mercedes Benz 500K Assembly
Instructions
7/23/2019 Mercedes Benz i e Ltr (1)q
http://slidepdf.com/reader/full/mercedes-benz-i-e-ltr-1q 6/6
Glue in order, - .
Glue in order, - .
Arrow indicates 'up'.
Arrowindicates 'up'.
Arrow indicates 'up'.
Pink flap indicates outer side.
Affix outer surface of tire like a bowl,then wait until glue is dry before gentlypulling the tire into shape.
Affix outer surface of tire like a bowl,then wait until glue is dry before gentlypulling the tire into shape.
Pink flap indicates outer side.
Pink flap indicates outer side.
The joining part is the lowest point.
The joining part is the lowest point.
The joining part is thelowest point.
Affix outer surface of tire like a bowl,then wait until glue is dry before gentlypulling the tire into shape.
Confirm top/bottombefore gluing.
Confirm top/bottom before gluing.
Top
Top
Apply glue around the mountain foldlines and adhere them.
Affix all four tires, adjusting tobe sure they touch the ground.
Shaded areas in diagrams indicate reverse side of parts.
Joint should be positioned at the top.
Joint should be positioned at the top.
Mercedes Benz 500K Assembly
Instructions