Embed Size (px)
Citation preview
MACHINE VISE
DIGITAL DESIGN GRAPHICS TECHNOLOGY
JIM KISIEL DDGT 121 1 OF 6 1/27/2011
MACHINE VISE
NAME:
COURSE:
DATE:
DWG NAME: SHEET NO.
PARTS LISTMATERIALDESCRIPTIONPART NAMEQTYITEM
C1 BASE11SAE #3140 JAW PLATE22C R S HANDLE ROD13SAE #1020 HANDLE BALL24STEEL#000 TAPER PIN25SAE #3140 VISE SCREW16SAE #1020 SPECIAL KEY17SAE #1020 COLLAR18C1 SLIDING JAW19SAE #1020 SLIDE KEY210SAE #1016 SET SCREW211STEEL, MILDSLOTTED 100° FLAT
COUNTERSUNK HEAD TAPPING SCREW - TYPE B
ANSI B18.6.4 - 1/4 - 14 - 5/8
412
EXPLODED MACHINE VISESCALE 1 / 2 DIGITAL DESIGN
GRAPHICS TECHNOLOGY
JIM KISIEL DDGT 121 2 OF 6 1/27/2011
MACHINE VISE
NAME:
COURSE:
DATE:
DWG NAME: SHEET NO.
PARTS LISTPART NAMEQTYITEM
BASE11JAW PLATE22HANDLE ROD13HANDLE BALL24TAPER PIN25VISE SCREW16SPECIAL KEY17COLLAR18SLIDING JAW19SLIDE KEY210SET SCREW211ANSI B18.6.4 - 1/4 - 14 - 5/8
412
9
11
8
7
6
4
4
10
3
12
2
1
10 5
5
BASESCALE 1 / 2
SECTION A-ASCALE 1 / 2
VIEW E-ESCALE 1 / 2
DIGITAL DESIGN GRAPHICS TECHNOLOGY
JIM KISIEL DDGT 121 3 OF 6 1/27/2011
MACHINE VISE
NAME:
COURSE:
DATE:
DWG NAME: SHEET NO.
AA
PARTS LISTPART NAMEQTYITEM
BASE11JAW PLATE22TAPER PIN25SPECIAL KEY17COLLAR18SLIDE KEY210
E
E
1.2551.250
1.0041.000
1 1/16"
5/8" - 8 ACME
R11/16"
2 3/4"
R1 1/8"
n5/16"4 X
DRILL
7 1/4"5"
5/16"
4"
5"
1 1/4"
2 3/16"
R1/4"
1 9/16"
3 5/16"
.502.498
1 3/4"
n1/4" 1/4 - 20UNC-2B, 5/8 DEEP 2 HOLES
1 1/2"
R1/4"4 X
5/8"
FILLETS AND ROUNDS 1/8R
R1 3/8"
.75
1 3/16"
1 3/8"
SPECIAL KEYSCALE 2 : 1
SLIDE KEYSCALE 1 : 1
COLLARSCALE 2 : 1
JAW PLATESCALE 1 : 1
DIGITAL DESIGN GRAPHICS TECHNOLOGY
JIM KISIEL DDGT 121 4 OF 6 1/27/2011
MACHINE VISE
NAME:
COURSE:
DATE:
DWG NAME: SHEET NO.
PARTS LISTPART NAMEQTYITEM
BASE11JAW PLATE22TAPER PIN25SPECIAL KEY17COLLAR18SLIDE KEY210
3/8"
.125.122
2 5/16"
3/16"
.341.340
1/8"
.186.185
13/16"
1/8"1/8"
3/4"Ø
3/8"13/16 -
20UNEF - 3A, LH
2 3/4"
1 1/2"5/8"
2 X DRILL AND CSK FOR1/4 FL HD MACH SCR
3/16"
1 3/4"
1"
n3/4"
n1/2" DRILL
1 1/16"
SLIDING JAWSCALE 1 : 1
VIEW D-DSCALE 1 : 1
DIGITAL DESIGN GRAPHICS TECHNOLOGY
JIM KISIEL DDGT 121 5 OF 6 1/27/2011
MACHINE VISE
NAME:
COURSE:
DATE:
DWG NAME: SHEET NO.
D
D
PARTS LISTPART NAMEQTYITEM
HANDLE ROD13HANDLE BALL24VISE SCREW16SLIDING JAW19SET SCREW211
R11/16"
1 3/4"
1 1/2"
.188.187
.219.217
.998.996
.750n.748 BORE X 1 3/16 DEEP,
FLAT BOTTOM 13/16 - 20UNEF - 3B, LH 7/16 DEEP
R1 3/8"
2 9/16"
3/8"
R1/8"
1 1/2"5/8"
1"
#25 DRILL (.1495)1 1/16 DEEP - 2 HOLES#12 (.216) - 24UNC - 2b 3/4 DEEP7_32 CBORE 3/8 DEEP
1/4-2OUNC-2B 5/8 DEEP X 2 .507
.504
2 3/16"
1 3/8"5/8" 1 3/8"
7/8" 7/8"
1 9/16"
R1/8" R1/4"
3/4"
SET SCREWSCALE 2 : 1
VISE SCREWSCALE 1 : 1
HANDLE BALLSCALE 1 : 1
HANDLE RODSCALE 1 : 1
DIGITAL DESIGN GRAPHICS TECHNOLOGY
JIM KISIEL DDGT 121 6 OF 6 1/27/2011
MACHINE VISE
NAME:
COURSE:
DATE:
DWG NAME: SHEET NO.
PARTS LISTPART NAMEQTYITEM
HANDLE ROD13HANDLE BALL24VISE SCREW16SLIDING JAW19SET SCREW211
3/4"
3/8"
1/16"
1/16"
n3/16"
.142n.140
1/4"
3 15/16"
1/4"
13/16"
R1/16"
7/16"
5/8 - 8ACME
6 1/4" #37 DRILL AND REAMFOR #000 TAPER PINCLEAR THROUGH PEEN SMALL END OVER
5 1/8" .312n.311
1/8"2 X
n3/8"
n1/8"#37 DRILL AND REAM WITH PART #3 IN PLACE
n3/4"
.131.128
#12 (.216)-24 UNC-2A
1/2"n
3/4"n
n1/2
n3/8
.313n.312
"M" (.295) DRILL 1/2 DEEP,
REAM
