INTRODUCTION - BTUReps · INTRODUCTION VIMCO is pleased and excited to release our newest marketing literature: the G-1010 booklet. This booklet provides condensed information on

INTRODUCTION

VIMCO is pleased and excited to release our newest marketing literature: the G-1010 booklet. This booklet providescondensed information on our entire range of vibration and noise isolation products. The information includesproduct features, application information, dimensional data and model selection tables. We expect this booklet to bean invaluable resource for engineers, representatives, distributors and contractors.

One new tool that we are introducing in this latest literature is our exclusive isolator 5 star rating system . Vibrationisolation efficiency is directly related to the amount of deflection (compression) of the isolating element. The isolationefficiency chart below illustrates the theoretical relationship between isolation efficiency, disturbing frequency andisolator static deflection

Disturbing frequency is the frequency of vibration produced by an unbalanced,rotating or reciprocating movement in mass.Natural frequency is the number of complete cycles of oscillation a mass will vibratein a given unit of time if a force displaces it from its equilibrium position and allows itto vibrate freely.Static deflection is the distance an isolator will deflect under the static or dead weightof the equipment.Isolation efficiency is the percentage reduction in the amplitude of the transmittedmechanical vibration.

We have classified our range of vibration isolators in 5 category's based on their isolation efficiency as detailed below.Each isolator selection table within this catalog indicates the isolator star rating.

* Isolator efficiencies are nominal based on equipment disturbing frequency of 1800rpm

www.vimco.biz G-1010 Rev. 2 (page 2)

Star rating Isolator Deflection Isolator efficiency Performance classification

more than 2.50"from 1.51" to 2.50"from 0.51" to 1.50"from 0.21" to 0.50"

up to 0.20" 92%96%98%99%

99.5%

BasicModerate

GoodVery GoodExcellent

Housed Spring Mounts

Features + Application Information1. Powder coated cast iron housings (70-110 micron ASTMD4138-07a) 5. Adjust mounting so that upper housing clears lower housing by2. Internal elastomeric snubbers prevent metal to metal contact at least 1/4" but not more than 1/2"3. Anti-skid elastomeric acoustical pad 6. Spring elements color-coded for easy field verification4. Built-in leveling device 7. Consult spring chart on page 22 for isolator performance data

Dimensional + Model Selection Data (Refer to page 2 for isolator star rating system)

ZA / ZB / ZC / ZD models 1" deflection series

(*) Free height 'H' indicated in table

is for ZA isolator. For free height of

ZB/ZC models, add 1/4". For free

height of ZD model add 1/2".

AA-1 / AB-1 / AC-1 / AD-1 models


is for AA-1 isolator. For free height

of AB-1/AC-1 models, add 3/8". For

free height of AD-1 model add 5/8".


2" deflection series



of AB-2/AC-2 models, add 1/2". For

free height of AD-2 model add 3/4".




of AB-4/AC-4 models, add 1/2". For While ordering specify mounting style model in place of "x" free height of AD-4 model add 3/4". e.g. for pin top internal adjustment order A B -1-110


Model AA-2:External adjustment

Model AB-2:Internal adjustment, pin top

Model ZA:External adjustment

Model ZB:Internal adjustment, pin top



Model AC-4:Internal adjustment, flat top

Model AD-4:Internal adjustment, neoprene top

Model ZC:Internal adjustment, flat top

Model ZD:Internal adjustment, neoprene top







6-1/2"

6-3/4"

7"

Due to our policy of continual product development and improvement, all specifications

311 to 410Ax-1-144 411 to 595

Ax-1-141-146B 596 to 647Ax-1-147

are subject to change without prior notice. Please consult your local rep. for updates.

Model Load RangeAx-1-140 1 to 80Ax-1-141 81 to 160Ax-1-142 161 to 310Ax-1-143

648 to 1190Ax-1-148A 1191 to 1576

Ax-1-147-146B 1577 to 1690

2381 to 3152Ax-2-147-146B 3153 to 3380

Ax-1-148A-146B 1691 to 2076

Ax-2-147 2077 to 2380

5-3/4"

6"

Zx-121

Ax-2-148A-146B 3381 to 4152

H (*)

4"

5-1/2"

2161 to 25002501 to 2660

Ax-4-147-146B 6306 to 6760

5331 to 55305531 to 62006201 to 7330

Ax-4-147 4153 to 4760Ax-4-148A 4761 to 6305

Ax-2-148A

Ax-4-148A-146B 6761 to 8305

3101 to 3665

3666 to 43304331 to 50005001 to 5330

Ax-4-110-113Ax-4-111-113Ax-4-112-113

Ax-2-112-113

1251 to 1330

2661 to 27602761 to 3100

1331 to 13801381 to 15501551 to 1832

1833 to 2160

131 to 210

751 to 910911 to 1080

1081 to 1250

211 to 300301 to 370371 to 700

701 to 750

Ax-4-109-113

Ax-2-112Ax-2-109-113Ax-2-110-113Ax-2-111-113

Ax-1-112-113

Ax-2-111

Ax-4-111Ax-4-112

Ax-1-112Ax-1-109-113Ax-1-110-113Ax-1-111-113

Zx-127

Ax-1-109Ax-1-110Ax-1-111

Zx-124

Model

Zx-125Zx-126

Load Range (lbs) H (*)

Zx-122Zx-123

1 to 5051 to 80

81 to 130

Free Standing Spring Mounts

Features + Application Information1. Large diameter laterally stable springs 5. Consult spring chart on page 22 for isolator performance data2. Anti-skid elastomeric acoustical cup / pad3. Built-in leveling device4. Spring elements color-coded for easy field verification


BA / BB / BD / BE / BG / BH / BN / BO / BP models WELD FREE CONSTRUCTION*WELD FREE CONSTRUCTION 1" deflection series

A B C D E F J Kn/a n/a n/a n/a 2 3/8" 3/8" 5/8" n/a

n/a n/a n/a n/a 2 7/8" 3/8" 5/8" n/a

6" 4" 5" 5/8" 2 3/8" 3/8" 5/8" 1/8" 3" deflection series6" 4" 5" 5/8" 2 7/8" 3/8" 5/8" 1/8"n/a n/a n/a n/a 2 3/8" n/a n/a n/a

n/a n/a n/a n/a 2 7/8" n/a n/a n/a

n/a n/a n/a n/a 1 1/2" 1/4" 3/8" n/a

4" 2" 3" 3/8" 1 1/2" 1/4" 3/8" n/a

n/a n/a n/a n/a 1 1/2" n/a n/a 1/8"

OSM-1A models*WELDED CONSTRUCTION

(CUP TYPE) WELDED CONSTRUCTION*Mounting holes furnished standard 1" deflection series*Galvanized finish

OSM-1B models*WELDED CONSTRUCTION

(CUP TYPE)

*Mounting holes furnished standard

*Galvanized finish 3" deflection series


7-3/4"

OSM-1B-186-199 1158 to 1470OSM-1B-187-199 1471 to 1825

333 to 580OSM-1B-186 581 to 850

211 to 332

OSM-1B-181

OSM-1B-157 751 to 910

131 to 210

HModel Load Range

4-1/2"(BA/BD models)

3-3/4"(BG models)

5-1/2"(BB/BE models)

4-3/4"(BH models)

H

BB-186-199 / BE-186-199 / BH-186-199 1158 to 1470

7-7/8"(BB/BE models)

7-1/8"(BH models)

BA-124 / BD-124 / BG-124 186 to 210BA-125 / BD-125 / BG-125 211 to 300

H

3-3/4"

5-5/8"

BNBOBP

301 to 370

OSM-1B-159-161 2083 to 2603

911 to 1500

BEBGBH

Model BP/BG/BH:w/o height adjustmentor anchoring option

Mount Series

BABBBD

Model BN/BA/BB:w/o base plate



OSM-1A-127

OSM-1B-158

Model

BA-126 / BD-126 / BG-126

Dimensions

OSM-1A-126

BB-187-199 / BE-187-199 / BH-187-199

Model BO/BD/BE:with base plate

1471 to 1825

OSM-1B-159 1501 to 2082

371 to 700OSM-1B-156 701 to 750

OSM-1A-125 211 to 300

OSM-1A-122

OSM-1B-187 851 to 1157

1 to 100OSM-1B-182 101 to 150OSM-1B-183 151 to 210OSM-1B-184OSM-1B-185

51 to 80OSM-1A-123 81 to 130OSM-1A-124

Load Range (lbs)OSM-1A-121 1 to 50

Model Load Range (lbs)

BN-043 / BO-043 / BP-043 36 to 65BN-044 / BO-044 / BP-044 66 to 90BN-045 / BO-045 / BP-045

HBN-041 / BO-041 / BP-041 1 to 15BN-042 / BO-042 / BP-042 16 to 35

3-1/4"(BN/BO models)

2-3/4"(BP models)91 to 185

301 to 370BA-127 / BD-127 / BG-127 371 to 700BB-156 / BE-156 / BH-156 701 to 750BB-157 / BE-157 / BH-157 751 to 910BB-158 / BE-158 / BH-158 911 to 1500

BB-159-161 / BE-159-161 / BH-159-161 2083 to 2603BB-159 / BE-159 / BH-159 1501 to 2082

Model Load RangeBB-181 / BE-181 / BH-181 1 to 100BB-182 / BE-182 / BH-182 101 to 150BB-183 / BE-183 / BH-183 151 to 210BB-184 / BE-184 / BH-184 211 to 332BB-185 / BE-185 / BH-185 333 to 580BB-186 / BE-186 / BH-186 581 to 850BB-187 / BE-187 / BH-187 851 to 1157

Free Standing Spring Mounts

Features + Application Information1. Large diameter laterally stable springs 5. Built-in leveling device2. Welded steel construction & galvanized finish 6. Spring elements color-coded for easy field verification3. Anti-skid elastomeric acoustical pad 7. Consult spring chart on page 22 for isolator performance data4. Mounting holes furnished as standard

Dimensional + Model Selection DataOSM-1 models

OSM-2 models

OSM-4 models

www.vimco.biz G-1010 Rev. 2 (page 7)are subject to change without prior notice. Please consult your local rep. for updates.



271 to 370OSM-1-154 371 to 500OSM-1-155 501 to 600OSM-1-156

H

1"

de

fle

cti

on

se

rie

s

OSM-1-150 1 to 100

4-7/8"

OSM-1-151 101 to 180OSM-1-152 181 to 270OSM-1-153

601 to 750OSM-1-157 751 to 910OSM-1-158 911 to 1500OSM-1-159 1501 to 2082

OSM-1-159-161 2083 to 2603

OSM-2-158 2604 to 30004-7/8"OSM-2-159 3001 to 4165

OSM-2-159-161 4166 to 5207

OSM-4-158 5208 to 60005-1/8"OSM-4-159 6001 to 8330

OSM-4-159-161 8331 to 10415Model Load Range (lbs) H

2"

de

fle

cti

on

se

rie

s

OSM-1-140 1 to 80

6-1/4"

OSM-1-141 81 to 160OSM-1-142 161 to 310OSM-1-143 311 to 410OSM-1-144 411 to 595

OSM-1-141-146B 596 to 647OSM-1-147 648 to 1190

OSM-1-148A 1191 to 1576OSM-1-147-146B 1577 to 1690

OSM-1-148A-146B 1691 to 2076

OSM-2-147 2077 to 2380

6-1/4"OSM-2-148A 2381 to 3152

OSM-2-147-146B 3153 to 3380OSM-2-148A-146B 3381 to 4152

OSM-4-147 4153 to 4760

6-1/2"OSM-4-148A 4761 to 6305

OSM-4-147-146B 6306 to 6760OSM-4-148A-146B 6761 to 8305

Model Load Range (lbs) H

3"

de

fle

cti

on

se

rie

s

.

OSM-1-181 1 to 100

7-1/4"

OSM-1-182 101 to 150OSM-1-183 151 to 210OSM-1-184 211 to 332OSM-1-185 333 to 580OSM-1-186 581 to 850OSM-1-187 851 to 1157

OSM-1-186-199 1158 to 1470OSM-1-187-199 1471 to 1825

OSM-2-187 1826 to 23167-1/4"OSM-2-186-199 2317 to 2950

OSM-2-187-199 2951 to 3650

OSM-4-187 3651 to 46327-1/2"OSM-4-186-199 4633 to 5910

OSM-4-187-199 5911 to 7300

Vertically Restrained Spring Mounts

Features + Application Information1. Applications requiring vertical restraint due to reduced equipment 4. Elastomeric 'non-short circuiting' grommets loads or large external forces e.g. wind 5. Built-in leveling device2. Welded steel construction & galvanized finish 6. Spring elements color-coded for easy field verification3. Mounting holes furnished as standard 7. Consult spring chart on page 22 for isolator performance data

Dimensional + Model Selection DataRSM-1 models

RSM-2 models

RSM-4 models

* RESTRICTO TM assembly limits vertical movement due to reduced

loads or external forces (wind loads)

* Adjust RESTRICTO TM assembly vertical limiting nuts as per clearance

levels specified by project engineer (standard: 1/4", maximum: 1/2")



RSM-4-187 3651 to 46328-7/8"RSM-4-186-199 4633 to 5910

RSM-4-187-199 5911 to 7300

RSM-2-187 1826 to 23168-3/8"RSM-2-186-199 2317 to 2950

RSM-2-187-199 2951 to 3650

RSM-1-186-199 1158 to 1470RSM-1-187-199 1471 to 1825

RSM-1-186 581 to 850RSM-1-187 851 to 1157

151 to 210RSM-1-184 211 to 332RSM-1-185 333 to 580


3"

de

fle

cti

on

se

rie

s

.

RSM-1-181 1 to 100

8-1/4"

RSM-1-182 101 to 150RSM-1-183

RSM-4-147 4153 to 4760

7-7/8"RSM-4-148A 4761 to 6305

RSM-4-147-146B 6306 to 6760RSM-4-148A-146B 6761 to 8305

7-3/8"RSM-2-148A 2381 to 3152

RSM-2-147-146B 3153 to 3380RSM-2-148A-146B 3381 to 4152

RSM-1-148A-146B 1691 to 2076

RSM-2-147 2077 to 2380

RSM-1-148A 1191 to 1576RSM-1-147-146B 1577 to 1690

RSM-1-141-146B 596 to 647RSM-1-147 648 to 1190

161 to 310RSM-1-143 311 to 410RSM-1-144 411 to 595


2"

de

fle

cti

on

se

rie

s

RSM-1-140 1 to 80

7-1/4"

RSM-1-141 81 to 160RSM-1-142

RSM-4-158 5208 to 60006-1/2"RSM-4-159 6001 to 8330

RSM-4-159-161 8331 to 10415

RSM-2-158 2604 to 30006"RSM-2-159 3001 to 4165

RSM-2-159-161 4166 to 5207

RSM-1-159 1501 to 2082RSM-1-159-161 2083 to 2603

RSM-1-157 751 to 910RSM-1-158 911 to 1500

RSM-1-155 501 to 600RSM-1-156 601 to 750

181 to 270RSM-1-153 271 to 370RSM-1-154 371 to 500


1"

de

fle

cti

on

se

rie

s

RSM-1-150 1 to 100

5-7/8"

RSM-1-151 101 to 180RSM-1-152

Seismic Restrained Spring Mounts (All-Directional)

Features + Application Information1. Large diameter laterally stable springs 5. All isolators certified to withstand minimum 1.39 G force2. Welded steel construction 6. Suitable for most seismic zone IV applications3. Built-in leveling device 7. Spring elements color-coded for easy field verification4. Mounting holes furnished as standard 8. Consult spring chart on page 22 for isolator performance data


SSMA-1 models 1" deflection series

2" deflection series

*Powder coated housing (50-70 micron ASTMD4138-07a)

*Housing will be elevated from ground when installed.

Pull down to floor with anchor bolts.

B C6" 3" 3" deflection series7" 4"

SSM-1 models

Select SSM-1 models instead of SSMB-1 where higher 'G' ratings are required.

'G' ratings for SSMA-1 based on shake table testing at ISO 17025 accredited

laboratory in accordance with ASCE 7-05 design parameters under OSHPD

Special Seismic Certification Preapproval (OSP) program.

'G' ratings for SSM-1, SSMB-1 based on attachment to steel. For concrete

ratings will be controlled by attachment methods + concrete strength.

*Zinc metallized housing


2.14 / 2.991.74 / 2.43

5.59 / 7.81

1.39 / 1.94

'G' Rating

3.03 / 4.242.29 / 3.2

648 to 11901191 to 1576

21.77 / 30.4211.58 / 16.188.69 / 12.15

6.08 / 8.5

81 to 160



32.5019.6911.817.515.284.332.32

3.95 / 5.524.82 / 6.74

1577 to 1690

311 to 410411 to 595

2.41 / 3.371.73 / 2.42

1691 to 2076

43.87 / 61.31

SSMB-1-143 / SSM-1-143SSMB-1-144 / SSM-1-144

SMB-1-148A-146B / SSM-1-148A-146

Load Range (lbs)1 to 80

1501 to 2082

SSMB-1-147-146B / SSM-1-147-146B

SSMB-1-140 / SSM-1-140SSMB-1-141 / SSM-1-141

SSMB-1-147 / SSM-1-147

SSMB-1-159-161 / SSM-1-159-161

SSMB-1-148A / SSM-1-148A

371 to 700

701 to 750

2083 to 2603

SSMB-1-141-146BSM-1-141-146B 596 to 647

161 to 310

Model

SSMA-1-127

SSMB-1-156 / SSM-1-156SSMB-1-157 / SSM-1-157

Model

SSMA-1-125SSMA-1-126

SSMA-1-121SSMA-1-122SSMA-1-123

SSMB-1-158 / SSM-1-158

SSMA-1-124

SSMB-1-142 / SSM-1-142

SSMB-1-159 / SSM-1-159

'G' Rating

131 to 210

751 to 910911 to 1500

211 to 300

1 to 5051 to 80

81 to 130

Load Range (lbs)

301 to 370

'G' RatingSSM-1-181 1 to 100 47.05

Model Load Range

30.42SSM-1-183 151 to 210 22.48SSM-1-182 101 to 150

15.21SSM-1-185 333 to 580 8.32SSM-1-184 211 to 332

581 to 850 5.67SSM-1-187 851 to 1157 4.37SSM-1-186

1158 to 1470 3.28SSM-1-187-199 1471 to 1825 2.77SSM-1-186-199

Mount Series

DimensionsA D E

1-1/2"SSMB-1 7-3/8" 5-1/2" 2-1/2"SSMA-1 4-5/8" 4-1/2"

Vibration Isolation Pads

Features + Application Information1. Simple field installation2. Wherever bolting is to be avoided and minor, non-critical vibration conditions exist (pumps, motors, a/c units, generators etc.)


3RFP series Defl.* Higher deflection than conventional pads

* Excellent resistance to oil, water, ozone

(suitable / recommended for outdoor use)

* Closed cell construction with excellent sound

attenuation capability

* Free from sulfur, halogens, formaldehydes,

phthalates and other toxins

* Lifetime warranty against core separation

Maximum loading: 70 psi

Material: closed cell, chemically cross-linked HD rubber foam (with LD core)

RMP series* Alternate high-low rib construction

* High quality ozone + water resistant elastomer


Material: 55 duro elastomer blend

CRMP series* Alternate high-low rib construction

* Environment friendly 100% natural cork core

* Excellent sound attenuation capability



Material: Low density cork, elastomer blend

ECRMP series* New 1" modules offer greater versatility at

jobsite to cut to exact size requirements.

* Easy cut construction (by hand or utility knife)

* Waffle pad design with inbuilt suction cups



Material: 55 duro elastomer blend

SRMP series


Maximum loading: 60 psi Contact factory for non-standard sizesMaterial: 55 duro elastomer blend, Galvanized steel plate


Alternate high-low rib construction Waffle pad design with inbuilt suction cups



SRMP-2R SRMP-3R SRMP-2E SRMP-3E

SR

MP

ser

ies

SRMP-2R 0606

Model Size Max load (lbs)

3RF

P s

erie

s

3RFP 181801 18" x 18" x 1" 22680

3RFP 030301 3" x 3" x 1" 630

.25"

3RFP 121201 12" x 12" x 1" 100803RFP 060601 6" x 6" x 1" 25203RFP 040401 4" x 4" x 1" 1120

3RFP 020201 2" x 2" x 1" 2803RFP 181802 18" x 18" x 2" 22680

.50"

3RFP 121202 12" x 12" x 2" 100803RFP 080802 8" x 8" x 2" 44803RFP 060602 6" x 6" x 2" 25203RFP 040402 4" x 4" x 2" 11203RFP 030302 3" x 3" x 2" 6303RFP 020202 2" x 2" x 2" 280

RM

P s

erie

s .

RMP 181838 18" x 18" x 3/8" 19440

RMP 030338 3" x 3" x 3/8" 540

.11"

RMP 121238 12" x 12" x 3/8" 8640RMP 060638 6" x 6" x 3/8" 2160RMP 040438 4" x 4" x 3/8" 960

RMP 020238 2" x 2" x 3/8" 240

CR

MP

ser

ies

CRMP 181801 18" x 18" x 1" 19440

CRMP 030301 3" x 3" x 1" 540

.18"

CRMP 121201 12" x 12" x 1" 8640CRMP 060601 6" x 6" x 1" 2160CRMP 040401 4" x 4" x 1" 960

CRMP 020201 2" x 2" x 1" 240CRMP 181802 18" x 18" x 2" 19440

.20"

CRMP 121202 12" x 12" x 2" 8640CRMP 060602 6" x 6" x 2" 2160CRMP 040402 4" x 4" x 2" 960CRMP 030302 3" x 3" x 2" 540CRMP 020202 2" x 2" x 2" 240

EC

RM

P s

erie

s

ECRMP 181834 18" x 18" x 3/4" 19440

ECRMP 020234 2" x 2" x 3/4" 240ECRMP 010134 1" x 1" x 3/4" 60

.18"

ECRMP 060634 6" x 6" x 3/4" 2160ECRMP 040434 4" x 4" x 3/4" 960ECRMP 030334 3" x 3" x 3/4" 540

.22"SRMP-2R 0404 4" x 4" x 13/16" 960SRMP-2R 0303 3" x 3" x 13/16" 540

6" x 6" x 13/16" 2160

.33"SRMP-3R 0404 4" x 4" x 1 1/4" 960SRMP-3R 0303 3" x 3" x 1 1/4" 540

SRMP-3R 0606 6" x 6" x 1 1/4" 2160

.36"SRMP-2E 0404 4" x 4" x 1 9/16" 960SRMP-2E 0303 3" x 3" x 1 9/16" 540

SRMP-2E 0606 6" x 6" x 1 9/16" 2160

SRMP-3E 0606 6" x 6" x 2 3/8" 2160.54"SRMP-3E 0404 4" x 4" x 2 3/8" 960

SRMP-3E 0303 3" x 3" x 2 3/8" 540

Double Deflection, Rubber-in-shear Mounts

Features + Application Information1. Anti-skid top and bottom surfaces 5. High deflection, low natural frequency2. Mounting holes furnished as standard 6. Elements color-coded for easy field verification3. Embedded steel plates for uniform loading (Color coding can be by 'dot' or 'complete element')4. Ozone + water resistant elastomer 7. Optional lock-down bolt and washer available

Dimensional + Model Selection DataFMD models (Refer to page 2 for isolator star rating system)

0.5" deflection series

A B C D E F G H

*Models FMD-E and FMD-F have

rectangular bases.

Light Duty Hangers

Features + Application Information1. Elements incorporate projected collar to prevent 4. AVHM provides up to 17dB(A) noise reduction metal to metal contact between rod and bracket 5. AVHM series designed for use with all thread rod2. Includes steel cups / plates for uniform loading 6. HNW series designed for use with wire, strap e.g. false ceiling, suspended3. Ozone + water resistant elastomer attic equipmentDimensional + Model Selection DataAVHM models HNW models

(Refer to page 2 for isolator star rating system) (Refer to page 2 for isolator star rating system)

AVHM series HNW series

A B C 1/5 0.43 0.73 1.28 1/5 1/5 0.43 1.02 1.67 1/5

1/5


Typical installation Typical installation

ModelLoad range

(lbs)Defl.(inch)

Color

HNW-1 1 to 65 REDHNW-2 66 to 120 BLACKHNW-3 121 to 200 BLUE

ModelLoad Range

(lbs)Defl.(inch)

Dimensions (in.)

AVHM-50 1 to 110AVHM-100 111 to 220

Model

FMD-A-1FMD-A-2FMD-A-3FMD-A-4

FMD-B-1FMD-B-2FMD-B-3

FMD-F-2FMD-F-3FMD-F-4

FMD-B-4

FMD-E-3FMD-E-4

FMD-F-1 501 to 750751 to 1000

1001 to 1500

236 to 375

376 to 400

116 to 130131 to 165166 to 235

401 to 500

1 to 3031 to 4041 to 70

71 to 115

1501 to 2200

Isolator Dimensions (inches)

1 3/4 2 3/8 3 1/8 5/16 11/32 1 1/4 1 3/8 3/16

2 3/8 3 3 7/8 3/8 11/32 1 3/4 1 3/4 7/32

1 3/4 1/42 3/8 3 1/8 4 3/8

ColorLoad Range (lbs)

BLUE

9/16 3 1/2 2 3/4 3/83 5/8 4 3/4 5 7/8

REDGREENBLACK

BLUERED

GREENBLACK

GREEN

BLACK



BLACK

BLUERED

GREEN1/2

1/2 2

Double Deflection, Rubber-in-shear Hangers

Features + Application Information1. Powder coated steel bracket (50-70 micron ASTM D4138-07a) 4. Ozone + water resistant elastomer2. Element incorporates projected collar to prevent 5. High deflection, low natural frequency metal to metal contact between rod and bracket 6. Elements color-coded for easy field verification3. Embedded steel plate(s) for uniform loading (Color coding can be by 'dot/stripe' or 'complete element')


APH / HND models 0.5" deflection series APH-A, HND-A, APH-B series have nominal 0.4" deflection

A B C D E

APHE / HNDE models 0.5" deflection series APHE-A, HNDE-A, APHE-B series have nominal 0.4" deflection

ColorA B C E H NH N NC

* Bottom washer only provided on HNDE

series elements


3 1/8 1/4 1 1/8 1.313 4 7/8 3/4

3 1/8 1 1/8 1 3/8 1.312 1/2 3 1/2 7/8 1/2

0.11 1.00 1.16

1 7/8 2 1/4 7/8 5/8 1.69 1/4 1 1/8

3/4

6 3 1/4 3 1/2 4

5/8

2.82 1.57 1.77 1.77

REDHND-A-3 41 to 70 GREEN

2 2 1/4 1/2

BLUE

BLACK

HND-A-1

BLACK

REDGREENBLACK

GREEN

BLACK

GREENBLACK

BLUERED

GREEN

GREENBLACK

BLUE

BLACK

REDGREEN

7/8 1/2

1.48 1.57 0.76 3/8

1 1/4 1 3/4

121 to 175

APHE-A-2 96 to 120

HNDE-A-1 1 to 30HNDE-A-2 31 to 40HNDE-A-3 41 to 70

71 to 120

3001 to 4200HNDE-D-3 2241 to 3000HNDE-D-4

HNDE-D-2 1308 to 2240

HNDE-B-4 376 to 572

HNDE-C-3 573 to 745HNDE-C-4 746 to 1307

HNDE-B-2 166 to 235

176 to 320

HNDE-B-3 236 to 375


0.59 3/80.81 1.18APHE-A-1 1 to 95

1.10 .840.710.11

1.31

APHE-B-1APHE-B-2

HNDE-A-4

HNDE-B-1 121 to 165

1/4 1 1/8 1.311 1/4

HND-C-4 746 to 1307 BLACK

Isolator dimensions (inches)Color

5/8

6 3 1/4 4 4 1/2

1.34

HND-D-2 1308 to 2240 REDHND-D-3 2241 to 3000 GREENHND-D-4 3001 to 4200 BLACK

HND-B-4 376 to 572 BLACK

HND-C-3 573 to 745 GREEN

4 1/2 1 7/8 2 1/4 3HND-B-3 236 to 375 GREEN

176 to 320

HND-B-1 121 to 165 BLUEHND-B-2 166 to 235 RED

APH-B-1 121 to 175 GREEN1/2

GREENAPH-A-2 96 to 120 BLACK

2.41 3/81.29APH-A-1 1 to 95

Color



Model Load Range (lbs)Isolator dimensions (inches)

1.65 1.77

APH-B-2 BLACK

1 to 30

3 1 3/8

HND-A-4 71 to 120

HND-A-2 31 to 40

Spring Hangers

Features + Application Information1. Powder coated steel bracket (50-70 micron ASTM D4138-07a) 5. Consult spring chart on page 22 for isolator performance data2. Load distribution steel washer3. Nuts, washers & rods by others4. Spring elements color-coded for easy field verification


3/4" deflection seriesE

1" deflection seriesE

n/a2" deflection series

E

n/a

3" deflection seriesE


4-1/8"34°

H

HSB-141

Model

2083 to 2603HSD-159-161

1 to 80Load Range (lbs)

HSB-148A-146B

Load Range (lbs)

1691 to 2076

333 to 580

596 to 647

1 to 100

81 to 160161 to 310

648 to 11901191 to 15761577 to 1690

28°

n/a

H

5-5/8"

28°

HSB-147HSB-148A

HSB-147-146B

6-1/2"30°

HSE-182 101 to 150

n/a

HSE-184 211 to 332151 to 210

D1/2"1/2"5/8"5/8"3/4"3/4"

30°

23°

46°

28°

311 to 410411 to 595

H

HSE-187HSE-186 581 to 850

1471 to 1825HSE-186-199 1158 to 1470

851 to 1157


36 to 6516 to 35

HSF-043

HSB-109HSB-110

1251 to 1500HSD-159

HSB-112

1501 to 2082

HSB-142

911 to 10801081 to 1250

186 to 210211 to 300301 to 370

751 to 910HSB-111

HSA-127

HSB-140

ModelHSS-021

Load Range (lbs)

26 to 55HSS-022

371 to 700701 to 750

1.8"

1 to 25

3-1/8"

4-5/8"

HSS-023

HSD-158

HSA-124HSA-125HSA-126

HSS-024

HSF-041

HSF-044HSF-045

HSF-042

H

2.3"66 to 90

86 to 125

1 to 15

91 to 185

56 to 85

Hanger Series

Dimensions

HSB-143

A B C

HSF 3.47" 2.15" 1.5"



HSE-183

HSB-144HSB-141-146B

ModelHSE-181

HSE-187-199

HSE-185

HSS 2.72" 2.15" 1.5"

HSB 7-1/2" 3" 2-3/4"HSA 4-1/2" 3" 2-1/4"

HSE 8-3/4" 3-1/2" 2-3/4"HSD 6-3/8" 3-1/2" 2-3/4"

Neo-SpringTM Hangers

Features + Application Information1. Powder coated steel bracket (50-70 micron ASTM D4138-07a) 5. Ozone & water resistant elastomer elements with embedded2. Load distribution steel washer + embedded steel plates steel plates and incorporating projected collar to prevent metal3. High deflection, low natural frequency to metal contact between rod and bracket4. Spring / rubber elements color-coded for easy field verification 6. Consult spring chart on page 22 for isolator performance data


1.5" deflection seriesH 1 E

n/a2" deflection series

2.5" deflection seriesH 1 E

1-1/4"

n/a

(Refer to page 2 for isolator star rating system)

1" deflection series 3.5" deflection seriesH 1 H 2 E H 1 E

1-1/4"


3/4"HNSE-Dx 11-13/16" 4-1/8" 4"

1/2"HNSE-B/Cx 11-13/16" 4-1/8" 4" 5/8"HNSE-Ax 11-13/16" 4-1/8" 4"

28°

2.3" 23°

3-3/8" 46°

Model Load Range (lbs)HNSF-HM-041 1 to 15

3" 28°

n/a

28°

5/8"

4-5/8"

4-1/8"

3"

1" 5-5/8"HSB-HM-142 161 to 310

1/2"5/8"

HNSB-B/C/Dx 10-3/16" 4-1/2" 4"

30°

n/a

46°

28°

34°

28°

H 2

3-3/8"

H 2

5-5/8"

H 2

6-1/2"

1-3/4"

3"

1-1/4"

1-3/4"

1-3/4"

HSB-HM-112 1081 to 1250

HSB-HM-109 701 to 750HSB-HM-110 751 to 910

131 to 210HSB-HM-125 211 to 300

4-5/8"

HSB-HM-126 301 to 370HSB-HM-127 371 to 700

HSB-HM-111 911 to 1080

1"

HNSF-HM-045 91 to 185

HNSF-HM-042

HSB-HM-124

16 to 35HNSF-HM-043 36 to 65HNSF-HM-044 66 to 90



Hanger Series

DimensionsA B C D

3/8"HSB-HM 7-1/2" 3" 2-3/4" 3/8"

HNSF-HM 4.85" 2.15" 1.5"

2-3/4"HNSA-Bx 8" 3" 2-3/4"

HNSE-D2-159 1501 to 2082

1/2"HNSB-Ax 10-3/16" 4-1/2" 4"

HNSA-Ax 8" 3"


HNSB-C3-108 583 to 620

HNSA-A3-121 1 to 50HNSA-A4-122 51 to 80HNSA-B1-123 81 to 130HNSA-B2-124 131 to 210HNSA-B3-125 211 to 300HNSA-B3-126 301 to 370HNSA-B4-127 371 to 582

HNSB-C4-111 911 to 1080

HNSB-C4-109 621 to 750HNSB-C4-110 751 to 910

HNSB-C4-112 1081 to 1250

1 to 80HSB-HM-141 81 to 160HSB-HM-140

HNSE-D3-159-161 2083 to 2603

HNSE-D2-158 1251 to 1500

HSB-HM-143 311 to 410

1 to 80HNSB-B1-141 81 to 160

HSB-HM-144 411 to 595HSB-HM-147 648 to 1190

Model Load RangeHNSB-A4-140

411 to 595HNSB-C3-141-146B 596 to 647

HNSB-B3-142 161 to 310HNSB-B4-143 311 to 410HNSB-C3-144

648 to 1190HNSB-D2-148A 1191 to 1576

HNSB-D2-147-146B 1577 to 1690

HNSB-C4-147

HNSB-D2-148A-146B 1691 to 2076

Model Load Range (lbs)HNSE-A4-181 1 to 100

HNSE-B3-184 211 to 332

HNSE-B1-182 101 to 150

HNSE-C4-186 581 to 850HNSE-C4-187 851 to 1157

HNSE-C3-185 333 to 580

HNSE-B2-183 151 to 210

HNSE-D2-187-199 1471 to 18251158 to 1470HNSE-D2-186-199

Union/Screwed Connection, Rubber Expansion Joints

Features + Application Information1. Reduces noise and vibration transmission 7. Synthetic fiber reinforcement2. Eliminates stress due to thermal expansion and piping misalignment 8. Corrosion resistant materials3. Precision molded of synthetic rubber 9. Easy field installation4. Threading standard as per customer specifications (NPT, BSPT)5. Applicable fluids for standard construction: water (cold, hot or sea), weak acids, alkalis, compressed air etc.6. Different elastomers are available for other fluids (e.g. oil). Contact factory for technical assistance

Dimensional + Model Selection Data

FCU models (twin bellow) FCU series (twin bellow)Size Length Axial Axial Transverse Angular Operating Burst

L compression elongation deflection deflection pressure pressure

(inches) (inches) (inches) (inches) (inches) (deg) (psig) (psig)

1/2 8 7/8 1/4 7/8 30° 150 7003/4 8 7/8 1/4 7/8 30° 150 7001 8 7/8 1/4 7/8 25° 150 700

1 1/4 8 7/8 1/4 7/8 25° 150 7001 1/2 8 7/8 1/4 7/8 20° 150 700

2 8 7/8 1/4 7/8 15° 150 700Materials (see figure) Ratings indicated above are for constant pressures at 100°F. For pulsating pressures use 1/2 of

No. rating; for surge pressures use 1/6 of rating. For elevated temperature ratings, consult factory.

1 Expansion joints must be installed per FSA technical handbook guidelines.

23

FCU-T / FCU-TH models (twin bellow) FCU-T series (twin bellow)Size Length Axial Axial Transverse Angular Operating Burst

(F/F) compression elongation deflection deflection pressure pressure


1/2 8 7/8 1/4 7/8 30° 232 7253/4 8 7/8 1/4 7/8 30° 232 7251 8 7/8 1/4 7/8 25° 232 725

1 1/4 8 7/8 1/4 7/8 25° 232 7251 1/2 8 7/8 1/4 7/8 20° 232 725

2 8 7/8 1/4 7/8 15° 232 725FCU-SH models (single bellow) FCU-TH series (twin bellow)

Size Length Axial Axial Transverse Angular Operating Burst

(F/F) compression elongation deflection deflection pressure pressure


1/2 6.30 3/5 2/5 3/5 20° 355 10663/4 6.30 3/5 2/5 3/5 20° 355 10661 6.30 3/5 2/5 3/5 20° 355 1066

1 1/4 8.35 3/5 2/5 4/5 30° 355 10661 1/2 8.35 3/5 2/5 4/5 30° 355 1066

2 8.78 3/5 2/5 4/5 30° 355 1066Materials (see figures) FCU-SH series (single bellow)No. Size Length Axial Axial Transverse Angular Operating Burst

1,2 (F/F) compression elongation deflection deflection pressure pressure

3,4 (inches) (inches) (inches) (inches) (inches) (deg) (psig) (psig)

5 1/2 5.12 5/16 5/32 5/16 15° 355 10666 3/4 5.12 5/16 5/32 5/16 15° 355 10667 1 5.12 5/16 5/32 5/16 15° 355 10668 1 1/4 5.35 5/16 5/32 5/16 15° 355 1066

1 1/2 5.35 5/16 5/32 5/16 15° 355 10662 5.98 5/16 5/32 5/16 15° 355 1066

Ratings indicated above are for constant pressures at 100°F. For pulsating pressures use 1/2 of

rating; for surge pressures use 1/6 of rating. For elevated temperature ratings, consult factory.

Expansion joints must be installed per FSA technical handbook guidelines.


FCU-SH-7FCU-SH-10FCU-SH-12FCU-SH-15

Model

FCU-SH-5

BoltsReinforcing fabric



PolyesterZinc plated carbon steel

FCU-SH-20

Model

FCU-5FCU-7

FCU-10FCU-12FCU-15FCU-20

Model

FCU-T-5FCU-T-7

FCU-T-10FCU-T-12FCU-T-15FCU-T-20

Model

FCU-TH-5FCU-TH-7

FCU-TH-10FCU-TH-12FCU-TH-15FCU-TH-20

Threaded union Cast SUS 201EPDMZinc plated carbon steel

Cast SUS 201MaterialPart

FlangesNutsTube

Part

Tube EPDM

MaterialUnion Malleable ironReinforcing fabric Polyester

Temp.

range

(°F)

-4 to 212-4 to 212-4 to 212-4 to 212-4 to 212-4 to 212

Temp.

range

(°F)

14 to 15814 to 15814 to 15814 to 15814 to 15814 to 158

Temp.

range

(°F)

14 to 15814 to 15814 to 15814 to 15814 to 15814 to 158

Temp.

range

(°F)

14 to 15814 to 15814 to 15814 to 15814 to 15814 to 158

Flanged Connection, Rubber Expansion Joints

Features + Application Information1. Reduces noise and vibration transmission 7. Synthetic fiber reinforcement2. Eliminates stress due to thermal expansion and piping misalignment 8. Corrosion resistant materials3. Precision molded of synthetic rubber 9. Easy field installation4. Floating flanges drilling standards as per customer specifications (ANSI, BS, DIN, JIS)5. Applicable fluids for standard construction: water (cold, hot or sea), weak acids, alkalis, compressed air etc.6. Different elastomers are available for other fluids (e.g. oil). Contact factory for technical assistance


Materials (see figures) Control unit composition:No.1

234

Pipe Axial Axial Transverse Angular Axial Axial Transverse Angular

Size L D F compression elongation deflection deflection compression elongation deflection deflection PSIG(inches (inches) (inches) (inches) (inches) (inches) (inches) (deg) (inches) (inches) (inches) (deg) 215

1151 1/4 6 1.58 2.72 1/2 3/8 1/2 15° 0.31 0.15 0.31 15° 3621 1/2 6 1.58 2.72 1/2 3/8 1/2 15° 0.31 0.15 0.31 15° 232

2 6 2.05 3.39 1/2 3/8 1/2 15° 0.31 0.19 0.31 15° 2272 1/2 6 2.68 4.18 1/2 3/8 1/2 15° 0.47 0.23 0.39 15° 113

3 6 3.00 4.57 1/2 3/8 1/2 15° 0.47 0.23 0.39 15° 3554 6 4.06 5.91 5/8 3/8 1/2 15° 0.70 0.39 0.47 15° 2275 6 5.04 7.09 5/8 3/8 1/2 15° 0.70 0.39 0.47 15° Ratings indicated above are for constant

6 6 5.99 8.23 5/8 3/8 1/2 15° 0.70 0.39 0.47 15° pressures at 100°F. For pulsating

8 6 7.64 10.24 5/8 3/8 1/2 15° 0.98 0.55 0.86 15° pressures use 1/2 of rating; for surge

10 8 9.85 12.60 3/4 1/2 3/4 15° 0.98 0.55 0.86 15° pressures use 1/6 of rating. For elevated

12 8 11.82 14.45 3/4 1/2 3/4 15° 0.98 0.55 0.86 15° temperature ratings, consult factory.

14 8 12.60 16.07 3/4 1/2 3/4 15° 0.98 0.62 0.86 15° Operating temp. range16 8 14.65 18.59 3/4 1/2 3/4 15° 0.98 0.62 0.86 15°

18 8 16.34 20.56 3/4 1/2 3/4 15° 0.98 0.62 0.86 15°

20 8 17.88 22.45 3/4 1/2 3/4 15° 0.98 0.62 0.86 15°

24 10 22.45 27.40 3/4 1/2 3/4 15° 0.98 0.62 0.86 15°28 10 26.77 31.49 3/4 1/2 3/4 15° 0.98 0.62 0.86 15°

1 1/2 7 1.58 2.72 2 3/4 1 3/4 35° 1 3/5 1 30° Control Units2 7 2.05 3.39 2 3/4 1 3/4 35° 1 3/5 1 30°

2 1/2 7 2.68 4.18 2 3/4 1 3/4 35° 1 3/5 1 30°

3 7 3.00 4.57 2 3/4 1 3/4 35° 1 3/5 1 30°

4 9 4.06 5.91 2 1 1 1/2 35° 1 3/4 3/4 30° Control units must be installed on

5 9 5.04 7.09 2 1 1 1/2 35° 1 3/4 3/4 30° unanchored systems or when test /

6 9 5.99 8.23 2 1 1 1/2 35° 1 3/4 3/4 30° surge / operating pressure exceeds

8 13 7.64 10.24 2 1/4 1 1 1/4 30° 1 3/4 3/4 30° the rating below:

10 13 9.85 12.60 2 1/4 1 1 1/4 30° 1 3/4 3/4 30°

12 13 11.82 14.45 2 1/4 1 1 1/4 30° 1 3/4 3/4 30°

14 14 12.60 16.07 1 1/2 3/4 1 1/4 20° 3/4 3/4 3/4 20°

16 14 14.65 18.59 1 1/2 3/4 1 1/4 20° 3/4 3/4 3/4 20°

18 14 16.34 20.56 1 1/2 3/4 1 1/4 20° 3/4 3/4 3/4 20°

20 14 17.88 22.45 1 1/2 3/4 1 1/4 20° 3/4 3/4 3/4 20° Expansion joints must be installed per

24 14 22.84 27.17 1 1/2 3/4 1 1/4 20° 3/4 3/4 3/4 20° FSA technical handbook guidelines.


FCT-240-H

2up to 8"Size Units / Joint

FCT-140-H

FCT-160-H

FCT-180-H

FCT-200-H

FCT-80-H

FCS models (single bellow)

FCT-180

FCT-200

FCT-240

Dimensions

Reinforcing fabric

Galvanized steel (drilling available as per ANSI/BS/DIN/JIS)Carbon steel wire strand

PartFlange

4

CRU models (control units)

2

FCT models (twin bellow)

Item Quantity12

MaterialTie Rod

Reinforcing ringTube

Polyester



Steel / Rubber washer

FCT-60

FCT-80

FCT-100

FCT-120

GussetNutsEPDM

FCT-60-H

FCT-Hup to 12"14" to 24"

FCT-50 FCT-50-H

FCS-180

FCT-100-H

FCT-120-H

FCT-140

FCT-160

FCS-160 FCS-160-H

FCS-100 FCS-100-H

FCS-140-H

Model

FCS-15 14" to 28"FCS-H

up to 12"FCS-15-H

FCT-40 FCT-40-H

FCT-20

FCT-25

FCT-30 FCT-30-H

FCT-20-H

FCT-25-H

Model

FCT-15

FCT

FCT-15-H

FCS-25-H

FCS-30 FCS-30-H

FCS-40 FCS-40-H

FCS-240-H

14" to 24"

FCS-280

FCS-180-H

FCS-280-H

FCS-140

FCS-80-H

FCS-200-H FCS-H

FCS-25

FCS-240

Twin Bellow: FCT series

Operating pressureSeries Size

FCSup to 12"14" to 28"

FCT-H series

FCS-200

16" thru 24" 45 psig

10" to 24" 4

5" thru 10" 135 psig12" thru 14" 90 psig

Size Pressure

Series °F

FCS-20 FCS-20-H

FCS-50-H

FCS-120 FCS-120-H

FCS-60 FCS-60-H

up to 12"

FCS-80

Single Bellow: FCS series FCS-H seriesFCS-12 FCS-12-H

FCS-50

up to 4" 150 psig

FCS 14 to 24014 to 194

FCT -4 to 212FCT-H 14 to 170

Stainless Steel Expansion Joints

Features + Application Information1. Reduces noise and vibration transmission 5. Corrosion resistant materials2. Vibration absorption and piping misalignment correction 6. Easy field installation3. Eliminates stress due to thermal expansion and piping misalignment4. Engineered bellow design ensures equal stress distribution through entire length


JF-500-T models JF-500-T series (threaded connection)Totallength

(inches)

10

10

10

10

12

12

Materials (see figure) Pressure ratings indicated above are based on 68°F ambient temperature. For elevatedNo. temperature ratings, consult factory.123

JF-500 / JF-500-H models JF-500 / JF-500-H series (flanged connection)Totallength

(inches)

6

6

6

6

6

6

8

8

89

6

6

6

6

6

6

8

8

8

9

Materials (see figure) Pressure ratings indicated above are based on 68°F ambient temperature. For elevatedNo. temperature ratings, consult factory.1223


JF-500-T-7

JF-500-T-10

JF-500-T-12



JF-500-H-30

JF-500-H-50

JF-500-H-80

JF-500-H-120

JF-500-T-15

Model

JF-500-T-5

JF-500-T-20

JF-500-120

JF-500-H-20

3/4

1

1 1/4

1 1/2

JF-500-80

JF-500-30

JF-500-50

5

8

12

Nominalbore

(inches)

1/2

2.762

12

2

8

3

5

3.99

9.21

2.75

1.06

1.28

1.81

2.20

BellowsO.D.

(inches)

0.75 ± 0.60

Axialmovement

(inches)

.59± 0.60

± 0.60

± 0.60

± 0.60

± 0.60

.78

.78

.70

.62

Max. lateraloffset

(inches)

.78

Operatingpressure

(psi)

300

-122 to +780300

300

300

300

300

-122 to +780

-122 to +780

-122 to +780

-122 to +780

Temp.range

(°F)

-122 to +780

PartBellowsBraidsTube end

JF-500-20 2

DescriptionSUS304 (SUS316 option)

SUS304

SUS304

Model Nominal

2.75 ± 0.60 .59 150

JF-500-25 2 1/2 3.40 ± 0.60

-122 to +780

.55 150 -122 to +780

JF-500-40 4 5.03 ± 0.60 -122 to +780

± 0.60 .47

-122 to +780

150

.31 150

-122 to +780

.39 150

JF-500-60 6 7.22 ± 0.60 .23 150 -122 to +780

6.16 ± 0.60

± 0.60 .31 150

.19 15013.42 ± 0.60

-122 to +780

JF-500-100 10 11.37 ± 0.60 .23 150 -122 to +780

JF-500-140 14 15.43 ± 0.60-122 to +780

.19 150 -122 to +780

JF-500-H-25 2 1/2 3.40 ± 0.60 -122 to +780

± 0.60 .59

-122 to +780

370

.47 370

-122 to +780

.55 370

-122 to +780

3.99 ± 0.60

JF-500-H-40 4 5.03 ± 0.60

3

.31 370

.39 370

-122 to +780

JF-500-H-60 6 7.22 ± 0.60 .23 370 -122 to +780

6.16 ± 0.60

-122 to +780

JF-500-H-100 10 11.37 ± 0.60 .23 370 -122 to +780

9.21 ± 0.60

-122 to +780

13.42 ± 0.60 .19 370

Max. lateral Operating

JF-500-H-140 14 15.58 ± 0.60 .19 370

.31 370

Temp.bore O.D. movement offset pressure range

Bellows Axial

(inches) (psi) (°F)

Part Description

(inches) (inches) (inches)

-122 to +780

Bellows SUS304 (SUS316 option)

Flange AISI 1015 (SUS304 option)

Tie Rods S25C

Gasket Rubber

Floating Floors

Features + Application InformationVIMCO floating floors provide a solution to the problem where the transmission loss of the standard structural floor is not sufficientto prevent noise from passing from mechanical rooms to noise-sensitive areas above or below it. Floating floors primarilycontrol airborne sound transmissions; they are not intended to be used in place of vibration isolators and/or inertia bases.

VIMCO floating floors perform acoustically on the sameprinciple as a double-glazed window : The separation of themasses, with an air gap, gives a much greater transmissionloss than if the two masses are combined into a continuousfloor. The "enclosed air cavity" is the primary isolator.

Vibration Management Corporation prefers and recommends a form-work floating floor construction over the lift slab / jack-upsystem offered by other manufacturers.

All types of floating floor construction perform the same acoustically as long as the dynamic natural frequency of the isolationmount, the air gap, and masses are the same. The choice of construction method therefore depends on economy, reliability, andease of installation. Jack-up system manufacturers generally claim lower installed costs. This cost differential tends to disappearthough, for larger areas where many equipment are supported on the floor, or where many plinths project through the floating floorfor equipment, piping support. In both cases the number of canisters has to be increased to provide proper edge and weightsupport. Most jack-up systems are designed for a 4" floating floor, with thicker slabs resulting in higher costs, not only due toextensions required on the canisters, but again in causing canister spacing to decrease. The VIMCO form-work system easilyaccommodates thicker floating floors with correct isolator selection. The form-work construction also offers the provision of afiberglass infill which in addition to preventing a sound tunneling effect, provides extra transmission loss. Independent lab tests bya competitor show that a 2" air gap with fiberglass infill gives a STC rating increase equivalent to doubling the air gap to 4" !!!

MaterialsVIMCO's form-work floating floor systemconsists of the following materials :

1. Roll-out isolation material provided with neoprene pads2. Closed cell perimeter isolating boards3. Plywood / cement board form-work4. Polyethylene bond-breaker sheeting5. Polyurethane perimeter sealant6. Neoprene contact adhesive7. Floating floor isolated drains8. Neoprene high load pads

VNRM-xx (xx denotes pad spacing in inches): Roll-out isolation materialVIMCO roll-out isolation material consists of low-density fiberglass with 2" high, resilient, neoprene isolation pads, embedded at24" centers as standard. Closer spacing between pads can be factory installed, or achieved at site using additional high load pads.VPPI-xx (xx denotes height in inches): Perimeter isolating boardsVIMCO incorporates closed cell expanded polyethylene sheets for perimeter isolation. These sheets have excellent weather-resistant characteristics and aid in preventing flanking noise along the edges of the floating floor area, by completing the isolationof the floating floor from the building structure.VNHP : High load padsVIMCO provides individual neoprene isolation pads for areas with additional, uneven loading. These pads can be factory installedwith the roll-out isolation material or can be furnished separately for installation at site, by a VIMCO authorized representative.VID-xx (xx denotes drain inlet size in inches): Isolated drainsVIMCO floating floor isolated drains consist of a two member housing, to drain water from the floating floor down to existingdrainage piping system, without compromising the structural isolation.Ancillary materials :Depending on economic considerations, local availability, the following materials may either be supplied by VIMCO or sourcedby your local VIMCO representative. Materials must however comply to VIMCO specifications to ensure proper installation.

Plywood / Cement board Neoprene spray adhesivePolyethylene sheeting Polyurethane sealant



VIMCO form-work floating floor

Air Mounts

Features + Application Information1. Air-cushioned isolation 5. Heavy wall construction2. Low natural frequency (3~5 Hz at operating load) 6. High lateral stability3. High deflection 7. Low maintenance4. Neoprene padded top and bottom base 9. Combined resiliency and air prevents drift or permanent set


AMA models AMA series

A B C D E0.47 1.97 3.94 3.90 3.100.47 2.36 3.94 3.90 3.100.47 3.54 5.43 3.90 3.100.47 4.33 6.46 3.90 3.100.55 5.91 8.35 3.90 3.100.55 9.45 12.36 3.90 3.100.55 12.99 16.22 3.90 3.10

Roof Curb Isolation Rails

Features + Application InformationVIMCO model AR aluminum spring rails are specifically designed and engineered as a vibration control system for curb mounted equipmentinstalled on the roof. The rails are custom designed to fit between standard roof curb and equipment, providing continuous support and an airand watertight seal. The system is adaptable to all curb systems and equipment without any modifications to either curb or equipment. Theassembly provides a cost effective method of providing vibration control for rooftop equipment in a lightweight and weatherproof unit.1. Construction - "Heavy wall" aluminum extrusion2. Sizes - 84" x 180" and smaller shipped in one piece. Units up to 85" x 450" shipped with splice kits for field assembly3. Springs - spaced and selected to provide uniform deflection after equipment is installed4. Corners - mitered and continuously welded exterior surface for complete weatherability5. Seal - weatherproof gasket is not exposed to elements. This eliminates deterioration of material6. Curb cap - flat bottom design adapts to all curb configurations7. Available in 1" and 2" deflectionsOptionsCable restraintsPictorial DescriptionTypical installation Cutaway view Section

Other Bases / Curbs

Cooling tower rails.Structural steel fan bases.** NEW ** Isolation curbs (roof curbs with integral spring isolators) now available. Contact factory for details.

www.vimco.biz G-1010 Rev. 2 (page 19)Due to our policy of continual product development and improvement, all specifications


Model Load Range (lbs)Part Dimensions (inches)

AMA-4 200 to 400

AMA-15 800 to 1500

AMA-45

Bolt Size

AMA-2 100 to 200 M10 x 40M12 x 50

AMA-8 400 to 800 M12 x 50M12 x 50

AMA-25 1400 to 2500 M16 x 60

Materials:

2400 to 4500 M16 x 60AMA-75 4000 to 7500 M16 x 60

Environmental Data -20 °F to + 180 °F

Resilient Element NeopreneMetal Structure Structural Steel

Bolted Inertia Bases

Features + Application InformationVIMCO model BIB bolted inertia bases are constructed of factory formed steel members. The modular construction design allows 6" intervallengths/widths and all standard thickness (4", 6", 8", 10", 12"). Inertia base components are supplied loose as standard for easy shipping andtransportation at jobsite. Bases can also be supplied fully assembled as an option. VIMCO offers free of cost engineering services to size baseand reinforcement per VIMCO / industry guidelines or project specifications. Job specific submittals are provided for each base, detailingload calculations and itemized component bill of materials. Standard design guidelines are: 1. Minimum 1:1 ratio between inertia base weight and equipment weight2. Base thickness shall be minimum 8% of the longest span between isolators3. Concrete reinforcement by 1/2" rebar at 8" center to center spacing4. (4) Adjustable height saving isolator mounting brackets supplied as standard5. Inertia bases are designed for post-drill concrete anchor boltsOptions(8) isolator mounting brackets instead of (4)T shaped basesPreassembled shipment

Pictorial DescriptionIso view Plan view Section

Welded Inertia Bases

Features + Application InformationVIMCO model IB inertia bases are specifically designed and engineered to receive poured concrete, for use in supporting mechanicalequipment requiring a reinforced concrete inertia base. Bases are available in 6", 8", 10" 12" thicknesses. VIMCO offers free of costengineering services to size base and reinforcement per VIMCO / industry guidelines or project specifications. Standard design guidelines are: 1. Minimum 1:1 ratio between inertia base weight and equipment weight2. Base thickness shall be minimum 8% of the longest span between isolators3. Concrete reinforcement by 3/8" rebar at 8" center to center spacing4. Height saving isolator mounting brackets supplied as standard5. Inertia bases are designed for post-drill concrete anchor boltsOptionsAnchor bolts or anchor bolt templates(6), (8) isolator mounting brackets instead of (4)T shaped bases

Pictorial DescriptionIso view Plan view Section

www.vimco.biz G-1010 Rev. 2 (page 20)Due to our policy of continual product development and improvement, all specifications


Seismic Snubber

Features + Application InformationVIMCO model SNB3-3050 is an all-directional (3-axis) device designed to restrain and decelerate motion of resiliently mountedequipment resulting from external loads or seismic activity, to acceptable limits. The device consists of interlocking welded steelmembers, separated by a molded neoprene insert. Neoprene element is designed to prevent direct metal to metal contact between2 steel members, and provide a minimum of 3/4" snubbing material in all directions. Device is manufactured to allow freeunrestricted movement of equipment of not less than 1/8", limited to a maximum of 1/4" before coming in to contact with energyabsorbing neoprene insert. Design also allows for removal of neoprene element for visual inspection and/or replacement.


Seismic Cable Restraint SystemApplication Information1. For permanent attachment of cable brace to structure / equipment / hanger2. Designed for use with 7x19 strand core pre-stretched galvanized aircraft cableSCRS models SCRS series

DIA. Code Size(") 04 3/8"

4-5/16 2 SC-01 1/8 975 05 1/2"5 2-1/4 SC-02 3/16 2050 06 5/8"5 2-5/8 SC-03 1/4 3150 07 3/4"

Features:Typical installation details 1. Quick installation (no shackles, thimbles, u-bolts, clevis angles....)

2. Cable easily slides into oversized front arch opening3. Breakaway hex nuts assure verification of proper installation4. Will swivel to final installation angle5. Low carbon steel, electro-galvanized finish6. Maximum load rating based on cable breaking strength

While ordering specify rod/bolt size code in place of "xx" e.g. for 1/8" cable with 3/8" bolt order SCRS-01- 04

SCRSA models SCRSA series

Model DIA. Code Size Code SizeSC-00 3/32" 600 02 1/4" 07 3/4"SC-01 1/8" 1100 04 3/8" 08 7/8"SC-02 3/16" 2667 05 1/2" 10 1"SC-03 1/4" 4400 06 5/8" 12 1-1/4"

Typical connection details Features:1. Complies with ASCE 19 and SMACNA Restraint Manual as required by FEMA, NEHRP, IBC, OSHPD, UNC, BOCA, SBCCI, other Building Codes2. Permanent end fitting3. Maintains break strength of cable and does not require thimbles4. (2) SCRSA's can be stacked on single rod to make a 4-way brace 5. Simple installation6. Maximum load rating based on cable breaking strength7. Supplied with 1 or 2 oval sleeves (depending on application)


SCRSA-03-xx 1/4" to 1-1/4"

Connection to structureConnection to equipment Connection to structure

Rod/Bolt codesModel

Rod / Bolt size (")

Cable Max Design Load



While ordering specify rod/bolt size code in place of "xx" e.g. for 3/32" cable with 3/8" bolt order SCRSA-00- 04

/ support member (concrete deck) (steel beam)

Model

Part Dimensions (inches)

SCRS-02-xx 3/8" to 3/4"

SCRS-01-xx 3/8" to 3/4"

SCRSA-02-xx 1/4" to 1-1/4"

SCRS-03-xx 3/8" to 3/4"

SCRSA-00-xx 1/4" to 1-1/4"

SCRSA-01-xx 1/4" to 1-1/4"

Rod/Bolt

ROD / BOLT A B Model

Cable Max Design Load (lbs)

MAXIMUM APPROVED LOADS:HORIZONTAL: 3050 lbs

VERTICAL: 3050 lbs

Springs

Features + Application Information1. High deflection, low natural frequency2. Springs should be selected in the range of minus 30% to plus 25% of rated load (RL)3. Springs electrogalvanized in accordance with ASTM B633-13 Type II, Class 2


SL: Load at which spring will become solid or theoretical maximum loadRL: Rated load based on ASHRAE defined 50% additional travel to solid

FSH: Free spring height


Deflection at SL(inches)

Spring constant(lb/inch)

RL(lbs)

SL(lbs)Main Stripe

ColorSpring no.



045101102103104105

110111

1 1/4

1 1/4 2 1/4

1 1/2

5

2

1 5/32

2 2 3/4

4

2

1 1/4

2 1/2

1 5/16

041042043044

106107108109

021022023024

112113121122123124125126127140141142143144147

148A146B150151152153154155156157158159161181182183184185186187199 SILVER

SILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVERSILVER

BLUERED

YELLOWWHITEBLUERED

YELLOWWHITEPINKPINK

BLACKBLUE

YELLOWBROWN

REDPURPLEORANGEGREENGRAYWHITEGOLD

NILBLUE

ORANGEBROWNBLACK

YELLOWRED

GREENBLUE

BLACKRED

GREENGRAYWHITE

YELLOWWHITE

BROWNORANGEGREEN

REDBLACKWHITEGRAYBLUEGOLD

NILREDPINK

GREENBLUE

YELLOWBROWN

REDWHITEBLACK

204470

10015335776

1485676

113150216300400500600733866

10004664066

11017324630056066

133250333476953

126140083

150216300400500600733

1200166641686

133180266486713926533

3066

105150235086

11522285

115170225325450600750900

11001300150070060

100165260370450840100200375500714

14301892600125225325450600750900

110018002500625130200270400730

10701390800

0.750.750.750.75

1.401.301.30

1.541.481.391.33

1.301.201.201.201.101.000.800.801.001.001.301.301.201.000.800.501.152.252.252.002.002.002.002.002.001.301.301.201.201.201.101.000.901.001.001.004.304.003.603.203.603.003.003.00

6189

131

15346287

174271375500682900

1375162515007004777

1382604639007314589

188250357715946

682900

30097

174271

267

305075

125

3 5/8

200350464

122318002500625

375500

GALVANIZED STEEL SPRINGS

Rating

168

4088

140200

1.33

O.D. FSH

2 1/2

1 11/16

6

LIMITED WARRANTY

Subject to terms and conditions herein, Vibration Management Corporation ("VIMCO") warrants to the original ownerat the original installation site that products manufactured by VIMCO ("Products") comply, at the time of manufacture,with VIMCO literature, and will be free from defects in materials and workmanship for a period of 12 months after thedate of start-up or 18 months after the date of shipment from factory, whichever shall be less (the "Warranty Period")

REMEDYA. The sole remedy for breach of this warranty is expressly limited to either the repair / ex-factory replacement, or

refund of VIMCO ex-factory sale price (at VIMCO's sole option), of any Product found to have manufacturingdefects under conditions of normal use within the Warranty Period. Installation is not included.

B. The owner must notify the original installer of the Product and VIMCO (Attn: Warranty Claims, 5930 Thomas RoadHouston, TX 77041), in writing, within the Warranty Period, providing a detailed description of all claimed defects.Transportation to factory or other designated facility for repairs of any Products or components of Products allegeddefective shall, in all events, be the responsibility and at the cost of the owner.

EXCLUSIONSVIMCO shall have no liability for:A. Incidental, special or consequential damages such as loss of the use of products, facilities or production,

inconvenience, loss of time or labor expense involved in repairing or replacing the alleged defective Product.B. The performance of any Product under conditions varying materially from those under which such Product is

usually tested under industry standards as of the time of shipment.C. Any damage to the Product due to abrasion, erosion, corrosion, deterioration, abnormal temperatures or the

influence of foreign matter or energy.D. The design or operation of owner's plant or equipment or of any facility or system of which any Product

may be made a part.E. The suitability of any Product for any particular application.F. Any failure resulting from misuse, modification not authorized by VIMCO in writing, improper installation

or lack of proper maintenance.G. Equipment furnished by owner, either mounted or unmounted, or when contracted for by the owner to be

installed or handled.

VIMCO's liability under this warranty shall not in any case exceed the VIMCO ex-factory sale price for the Productfound to be defective.

THIRD-PARTY WARRANTIESFor goods or components not manufactured by VIMCO, above mentioned warranty obligations of VIMCO shall be limitedby the warranty actually extended to VIMCO by its vendors.

SEVERABILITYTo the extent that any provision of this warranty would be void or prohibited under applicable law, such provisions shall be limited in effect to the minimum extent necessary to render the remaining provisions hereof enforceable.

NO OTHER WARRANTIESVIMCO makes no implied warranty of merchantability or fitness for particular purpose, or other warranties with respectto any products or services except as expressly set forth in this limited warranty.


T: +1-713-460-VIMCO F: +1-713-460-1100 E: [email protected] +1-713-460-8462

Houston - Texas 77041, USA

Documents

INTRODUCTION - BTUReps · INTRODUCTION VIMCO is pleased and excited to release our newest marketing literature: the G-1010 booklet. This booklet provides condensed information on