ELIS PLZEŇ a. s. PRODUCTS ULTRASONIC WATER AND FLOW METERS ELIS PLZEŇ a. s., Luční 15, 301 64 Plzeň, Czech Republic 1

ELIS PLZEŇ a. s. ELIS PLZEŇ a. s.

PRODUCTSPRODUCTS

ULTRASONIC WATER ULTRASONIC WATER ANDAND FLOW METERSFLOW METERS

ELIS PLZEŇ a. s., Luční 15, 301 64 Plzeň, Czech Republic1

ULTRASONIC FLOW METERSULTRASONIC FLOW METERS

• Intended for measurement of conductive and non- conductive clean liquids as water, demineralized water, fuel, oil, etc.

• Principal: transit time (measurement of time of flying ultrasonic beam from one to second transductor in direction of flow and in opposite direction of flow).

• The flow rate is calculated from difference of time.

• Flow meters are produced in single and dual beam version.

• They don’t have any moving parts

• They have min. pressure loses

2ELIS PLZEŇ a. s., Luční 15, 301 64 Plzeň, Czech Republic

• Produced categories of ultrasonic flow meters:Produced categories of ultrasonic flow meters:

• Battery supplied single or dual beam:Battery supplied single or dual beam:

• FLOMIC FL5024, FL5044 (DN32 to DN200)(DN32 to DN200)

• FLOMIC FL5034, FL5054 (DN32 to DN300)(DN32 to DN300)

• FLOMIC FL3085 (DN200 to DN1200)(DN200 to DN1200)

• FLOMIC FL3005 (DN200 to DN2000) for direct(DN200 to DN2000) for direct assembly into pipingassembly into piping

3


ELIS PLZEŇ a. s., Luční 15, 301 64 Plzeň, Czech Republic

• Main powered single or dual beam:Main powered single or dual beam:

• SONOELIS SE404X, SE406X (DN32 to DN300)(DN32 to DN300)

• SONOELIS SE401X, SE402X (DN200 to DN1200)(DN200 to DN1200)

• SONOELIS SE804X, SE806X (DN200 to DN1200)(DN200 to DN1200)for direct assembly in to pipingfor direct assembly in to piping

4



FLOMIC FL5024 (single beam)FLOMIC FL5044 (dual beam)

5

BATTERY POWERED BATTERY POWERED ULTRASONIC WATERULTRASONIC WATER METERS METERS



• Certified according to MID (European metrology certificate) and OIML R49

• Designed in observance of standard EN14154

• Intended for measurement of clean water and substitution Intended for measurement of clean water and substitution ofof mechanical water meters WOmechanical water meters WOLLTMAN typeTMAN type

• Intended for diagnostic of general condition of water network Intended for diagnostic of general condition of water network and water leakages in pipingand water leakages in piping

• They can measure instantaneous flow rate in both direction, They can measure instantaneous flow rate in both direction, consumption of water, pressureconsumption of water, pressure

• They don’t have any moving partsThey don’t have any moving parts• They have very low pressure loses They have very low pressure loses

6



FLOMIC FL5024 (single beam), FLOMIC FL5044 (dual beam)

• Nominal diameter: DN32 to DN200 (single beam), DN65 to DN200 (dual beam)

Technical parametersFLOMIC FL5024

FLOMIC FL5044

Nominal diameter 32 40 50 65 80 100 125 150 200

Overload flow [m3/hr] 12,5 20 31,25 50 78,75 125 200 312,5 500

Permanent flow [m3/hr] 10 16 25 40 63 100 160 250 400

Transition flow [m3/hr] 0,32 0,512 0,8 1,28 2,016 3,2 5,12 8,0 12,8

0,64 1,0 1,6 2,5 4,0 6,4

Min. flow [m3/hr] 0,2 0,32 0,5 0,8 1,26 2,0 3,2 5,0 8,0

0,4 0,63 1,0 1,6 2,5 4,0

Pulse number [liters/pulse]

10 10 25 50 50 100 100 100 250

7




• Material of sensor: casting from cast iron• Connection: flanges (EN, ANSI, JIS)• Water pressure class: MAP16• Temperature class: T50• Flow-profile sensitivity class: U5 (FL5044), U10 (FL5024) – in

front of meter D3 (FL5044), D5 (FL5024) – behind meter• Pressure loss class: ∆P10• Climatic and mechanical class: B• Electromagnetic environment: E1, E2• Display unit: single-line 8 character LC display• Flow rate sampling period: 1 sec• Protection class: IP68

8




• Power supply: Li battery 3,6 V/19Ah – live time 8 years

• Output: passive pulse output (U= 3 to 30V, I = 0,002 to 10mA, timp = 30ms)passive current output 4 to 20mA(U = 10 to 24 V)

• Optional equipment: bi-directional measurement (± passive pulse output)passive current output 4 to 20mA in

combination of electrical contact for flow directionUSB, RS232 or RS232 + USB converterGSM module FLODAT FD1.00

9




• BASIC DIMENSIONS and WEIGHT

Diameter 32 40 50 65 80 100 125 150 200

L [mm] 260 300 300 300 350 350 350 350 350

S [mm] 140 145 150 155 160 165 180 190 205

Weight [kg] 4,5 7 10 11 15 17,5 22,5 26 36,5

10




11

BATTERY POWERED BATTERY POWERED ULTRASONIC ULTRASONIC FLOW METERSFLOW METERS



• Intended for measurement of clean water• They can measure instantaneous flow rate in both direction,

consumption of water, pressure• They don’t have any moving parts• They have very low pressure loses

12



FLOMIC FL5034 (single beam), FLOMIC FL5054 (dual beam)

• Nominal diameter: DN32 to DN300 (single beam), DN40 to DN300 (dual beam)

Technical parameters

FL5034

FL5054

Nominal diameter

32 40 50 65 80 100 125 150 200 250 300

Overload flow [m3/hr]

20 31,25 50 78,75 125 200 250 312,5 500 787,5 1250

Permanent flow [m3/hr]

16 25 40 63 100 160 200 250 400 630 1000

Transition flow [m3/hr]

0,4 0,635 1,02 1,6 2,52 4,0 5,0 6,3 12,8 20,1 32,0

0,32 0,51 0,8 1,28 2,05 2,56 3,2 6,4 10,08 16,0

Min. flow [m3/hr]

0,25 0,397 0,635 1,0 1,587 2,54 3,17 3,97 8,0 12,6 20,0

0,2 0,32 0,5 0,8 1,28 1,6 2,0 4,0 6,3 10,0

Pulse number [liters/pulse]

10 10 25 50 50 100 100 100 250 250 500

13




• Material of sensor: weldment (measuring part is made from ss-steel 1.4403, flanges and cover from

carbon steel)• Connection: flanges (EN, ANSI, JIS)• Water pressure class: MAP16, MAP40• Temperature class: T50• Flow-profile sensitivity class: U5 (FL5044), U10 (FL5024) – in

front of meterD3 (FL5044), D5 (FL5024) – behind meter

• Pressure loss class: ∆P10• Climatic and mechanical class: B• Electromagnetic environment: E1, E2• Display unit: single-line 8 character LC display

14




• Flow rate sampling period: 1 sec• Power supply: Li battery 3,6 V/19Ah – live time 8 years • Protection class: IP68• Output: passive pulse output (U= 3 to 30V, I = 0,002 to 10mA,

timp = 30ms)passive current output 4 to 20mA (U = 10 to 24V)

• Optional equipment: complete ss-sensorbi-directional measurement (± passive pulse output)passive current output 4 to 20mA in combinationof electrical contact for flow directionUSB, RS232 or RS232 + USB converterGSM module FLODAT FD1.00

15



FLOMIC FL5034 (single beam)FLOMIC FL5054 (dual beam) • BASIC DIMENSIONS and WEIGHT

Diameter 32 40 50 65 80 100 125 150 200 250 300

L [mm] 360 360 360 360 360 360 360 360 450 450 450

S [mm] 175 180 185 190 200 210 225 235 255 280 305

Weight [kg] 1,6 MPa 18 19 20 29 46 59

Weight [kg] 4,0 MPa 10 10 12 13 16 18 21 22 38 71 85

16



FLOMIC FL3085 (single beam)

17




• Intended for measurement of clean water in big dimensions• Measurement of instantaneous flow rate in both direction

and consumption of water• Storage data• They don’t have any moving parts• They have very low pressure loses

18




• Nominal diameter: DN200 to DN1200 • Material of sensor: weldment, material from carbon

steel, painted• Connection: flanges (EN, ANSI, JIS)• Nominal pressure: PN6, PN10, PN16, PN40• Temperature of liquid: 0 to 150°C• Ultrasonic transductors: 2 pcs of US2.1 (manufactured by

ELIS PLZEŇ a. s.)• Display unit: single-line 8 character LC display• Power supply: Li-battery + 2 x Alkali batteries 9V,

live time 4 years• Transductors connection cable: max. 20m• Accuracy: ±1% in range 1:20

19




• Flow rate sampling period: 1 sec• Protection class: of electronic: IP65• Protection of sensor: IP54/IP68• Outputs: passive pulse output (U= 30V,

I = 10mA)passive current output 4

to 20mA (U = 24V)

• Optional equipment: complete ss-sensorbi-directional measurement (± passive

pulse output)passive current output 4 to 20mA in

combination of electrical contact for flow direction

USB, RS232 or RS232 + USB converter

20




21




22




23




• Intended for measurement of clean water on big piping • Installation directly to existing piping• Measurement of instantaneous flow rate in both direction

and consumption of water• Theoretical calibration after installation• Storage data

24




• Nominal diameter: DN200 to DN2000 • Nominal pressure: PN40• Temperature of liquid: 0 to 150°C• Ultrasonic transductors: 2 pcs of US2.1 (manufactured

by ELIS PLZEN a. s.)• Display unit: single-line 8 character LC display• Flow rate sampling period: 1 sec• Power supply: Li-battery + 2 x Alkali batteries 9V,

live time 4 years• Transductors connection cable: max. 20m• Protection class of electronic: IP65• Protection of sensor: IP54/IP68

25




• Output: passive pulse output (U= 3 to 30V, I = 10mA) passive current output 4 to 20mA, (U = 24V)

communication interface RS232• Accuracy: ± 2% in range 1:20• Optional equipment: bi-directional measurement (± passive

pulse output)passive current output 4 to 20mA in

combination of electrical contact for flow direction

USB, RS232 or RS232 + USB converter

26



SONOELIS SE404X (single beam)SONOELIS SE406X (dual beam)

27

MAIN POWEREDMAIN POWEREDULTRASONIC ULTRASONIC FLOW METERSFLOW METERS



• Intended for measurement of non conductive and conductive clean liquids as water, demineralized water, condensate, fuel, diesel, oil

• Measurement of instantaneous flow rate in both direction and consumption of water

• Measurement of mass flow and mass of water with connection of temperature sensor Pt100

• They don’t have any moving parts• They have very low pressure loses

28




• Nominal diameter: DN32 to DN300• Nominal pressure: PN16, PN40• Measurement accuracy: ±1% for velocity of liquid v>0,5 m/s (SE404X)• ±0,5% for velocity of liquid v>0,5 m/s (SE406X)• Temperature of liquid: 0 to 150°C• Ambient temperature: +5 to +55°C• Display unit: alpha-numerical LCD unit, 2 lines,

16 characters each• Power supply: 90 to 230V AC, 50 to 60Hz• Protection class: electronics IP65, sensor IP67

29




• Material of sensor: weldment (measuring part is made from ss-steel 1.4301, flanges and cover from carbon steel)

• Flow-profile sensitivity class: U5 (SE406X), U10 (SE404X) – in front of meterD3 (SE406X), D5 (SE404X) – behind meter

• Outputs: pulse output (selected 0.1 to 1,000 l/pulse)Frequency output, selected 0 t 1,000 Hz or 10kHzRelay type 24V AC/0,1A

30




• Optional equipment: communication line RS485extended temperature range for sensors: - 20° to 180°CCurrent output (0)4 to 20mAMass-flow rate measurement capabilityFlow rate measurement in two directionssensor protection class IP68100 m (max.) transductors connection cable

31




• METER VERSION, CONFIGURATION and TYPE DESIGNATION

VERSION COMPACT REMOTE

CONFIGURATION Economic Standard Comfort Economic Standard Comfort

SINGLE-BEAM SENSOR

SE4040 SE4042 SE4044 SE4041 SE4043 SE4045

DUAL-BEAM SENSOR

SE4060 SE4062 SE4064 SE4061 SE4063 SE4065

32




33



34




• Intended for measurement of non conductive and conductive clean liquids as water, demineralized water

• Measurement of instantaneous flow rate in both direction and consumption of water

• Measurement of mass flow and mass of water with connection of temperature sensor Pt100

• They don’t have any moving parts• They have very low pressure loses

35




• Nominal diameter: DN200 to DN1200• Nominal pressure: PN16, PN40• Measurement accuracy: ±1% for velocity of liquid v>0,5 m/s (SE401X)• ±0,5% for velocity of liquid v>0,5 m/s (SE402X)• Temperature of liquid: 0 to 150°C• Ambient temperature: +5 to +55°C• Display unit: alpha-numerical LCD unit, 2 lines,

16 characters each• Power supply: 90 to 230V AC, 50 to 60Hz• Protection class: electronics IP65, sensor IP54

36




• Material of sensor: weldment (material of measuring part flanges from carbon steel)

• Flow-profile sensitivity class: U5 (SE402X), U10 (SE401X) – in front of meter

D3 (SE402X), D5 (SE401X) – behind meter• Outputs: pulse output (selected 0.1 to 1,000 l/pulse)

Frequency output, selected 0 t 1,000 Hz or 10kHzRelay type 24VAC/0,1A

37




• Optional equipment: communication line RS485extended temperature range for sensors:

- 20° to 180°CCurrent output (0)4 to 20mAMass-flow rate measurement capabilityFlow rate measurement in two directionssensor protection class IP68100 m (max.) transductors connection

cable

38




• METER VERSION, CONFIGURATION and TYPE DESIGNATION

VERSION REMOTE

CONFIGURATION ECONOMIC STANDARD

COMFORT

SINGLE-BEAM SENSOR SE4011 SE4013 SE4015

DUAL-BEAM SENSOR SE4021 SE4023 SE4025

39




40



41




42




• Intended for measurement of clean water on big piping • Installation directly to existing piping• Measurement of instantaneous flow rate in both direction

and consumption of water• Measurement of mass flow and mass of water with connection

of temperature sensor Pt100• Theoretical calibration after installation

43




• Nominal diameter: DN200 to DN1200 • Nominal pressure: PN40• Temperature of liquid: 0° to 150°C• Ultrasonic transductors: 2 pcs of US2.1 (manufactured

by ELIS PLZEŇ a. s.)• Display unit: single-line 8 character LC display• Power supply: 90 to 250VAC, 50 to 60Hz• Transductors connection cable: max. 100m• Protection class of electronic: IP65• Protection of sensor: IP54

44




• Output: passive pulse output (U= 3 to 30V, I = 10mA)passive current output 4 to 20mA, (U =

24V)communication interface RS232

• Accuracy: ± 2% in range 1:20• Optional equipment: communication line RS485

extended temperature range for sensors-20° to 180°CCurrent output (0) 4 to 20mAMass-flow rate measurement capabilityFlow rate measurement in two directionssensor protection class IP68100 m (max.) transductors connection

cable

45



ELIS PLZEŇ a. s.ELIS PLZEŇ a. s.

Luční 15Luční 15

301 64 Plzeň301 64 Plzeň

Czech RepublicCzech Republic

PhonePhone: : +420 +420 377 517 751377 517 751

Fax: Fax: +420 +420 377 517 722377 517 722

E-mail: E-mail: [email protected]

http://www.elis.cz

46

Thank you for your attentionThank you for your attention


Documents

ELIS PLZEŇ a. s. PRODUCTS ULTRASONIC WATER AND FLOW METERS ELIS PLZEŇ a. s., Luční 15, 301 64 Plzeň, Czech Republic 1