Comat RELECO – Railway applications

Railway applications Relays Time relays Monitoring relays Sockets

Reliable and Safe Solutions for Railway and Transportation Applications Solutions for the transport market need to guarantee safety, security and comfort. The applications are expected to last a long time under challenging conditions. Be it for high-speed trains, metros, subways or other rail ve-hicles in tunnels, on bridges, in train stations, airports, on the open track, or in harbor facilities, the Comat Releco Group has the right solution for different kind of applications. We offer a wide range of relays, control and monitoring devices that are developed in compliance with the European Railway Standard EN 50155 (including also EN 61373, EN 45545 and NF F 16-101/102).

The EN 50155 standard applies for all electronic devices such as command, control, protection units, as well as power supplies, which are used in the transportation market. It applies either to the accumulator battery side or also the low-voltage power supply part of the vehicle.

Regarding fire protection, the products offered in this brochure are manufactured in accordance with standard NF F 16-101/102.

A table a the last page of this brochure shows the overview of the products and the standards they comply with. Individual declarations of conformity are available on demand. Please do not hesitate to contact us for any further questions or comments.

[email protected]

Comat AG Bernstrasse 4 3076 Worb Switzerland

www.comat.ch

Devices for superior requirements

1. Relays Page 3

Long life series with single contacts C31D/R 4

Long life series with twin contacts C32D/R 5

Standard relay R3-N3x 6

Standard relay R4-A4x 7

Miniature relay R7-A2x 8

Miniature relay R7-T2x 9

Interface relay CINT-21 10






Signal relay C203.06R 16

Power relay RIC20-x 17

Power relay RIC25-x 18

2. Time Relays Page 19

Time functions 20

Multifunction Timer, relay change-over CIM1R 21

Multifunction Timer, solid-state AC CIM12R 22

Multifunction Timer, solid-state DC CIM13R 23


Multifunction Timer, solid-state AC CIM22R 25

Multifunction Timer, solid-state DC CIM23R 26


Multifunction Timer, semi-conductor AC CIM32R 28

Multifunction Timer, semi-conductor DC CIM33R 29

CT-System: Plug-in time modules CT32R, CT33R, CT36R 30

Plug-in time relays CT32R, CT33R, CT36R 31

3. Monitoring Relays Page 33

1-phase monitoring MRU11R 34

3-phase monitoring MRU32R 35

1-phase monitoring MRI11R 36

3-phase monitoring MRI32R 37

1-phase monitoring MRM11R 38

3-phase monitoring MRM32R 39

CT-System: Plug-in current monitoring modules CT512R, CT515R, CT516R 40

Plug-in current monitoring set CT512R, CT515R, CT516R 42

Plug-in DC voltage monitoring module CT524R 41

Plug-in DC voltage monitoring set CT524R 42

Insulation monitoring ESU-D2R 43

4. Sockets Page 45

Socket for 11 pin relays and plug-in modules C11A (for relays: C31D/R, C32D/R, R3-N3) 46

Socket for 11 pin relays and plug-in modules C12B0 (for relays: C31D/R, C32D/R, R3-N3) 47

Socket for 14 pin relays CS-144 (for relays: R4-A4x) 48

Socket for miniature relays CS-118 (for relays: R7-x) 49

Index

Railway applications

1

Rela

ys

2

Tim

e Re

lays

3M

onito

ring

Rela

ys

4

Sock

ets

This issue replaces all previous issues. Availability, errors and specifications subject to change without notice.2 | Railway/01a.12

Notes

This issue replaces all previous issues. Availability, errors and specifications subject to change without notice. Railway/01a.12 | 3

1

Rela

ys

Application Types Output contacts Design

11 pin plug-in, long life relay C31D/R 10A, 250V AC-1

11 pin plug-in, long life relay C32D/R 6A, 250V AC-1

11 pin plug-in, standard relay R3-N3 6A, 250V AC-1

14 pin plug-in, standard relay R4-A4 10A, 250V AC-1

8 pin plug-in, miniature standard relay R7-A2 10A, 250V AC-1

8 pin plug-in, miniature standard relay R7-T2 6A, 250V AC-1

Interface relay CINT-21 6A, 250V AC-1






Interface relay C203.06 2x 2A, 125V AC-1

Power relay RIC20- ; ; 20A, 230V AC-1

Power relay RIC25- ; ; 25A, 230V AC-1

1. Relays


Long life series with single contacts

C31D/R11 pin plug-in relay, 3-pole, change-over contacts,according to IEC 60067

Type: C31D/R VLong Life Relays for Railway application, 3 change-over contactsTypes with LED status indicatorTypes with free wheeling diodeManual actuator and mech. status indicator

Maximum contact load 10 A / 250 V AC-1 10 A / 30 V DC-1Recommended minimum contact load 50 mA / 10 V

ContactsType single contact micro disconnectionMaterial AgCuNiRated current 10 AInrush current max. (20 ms) 40 ASwitching voltage AC-1 max. 250 VAC load max. 2500 VA AC-1DC load max. see Fig. 2

Coils (Values are valid at 20 C)Operating voltage range 0.7 1.25 UNNominal power DC 1.2 W

Coil Table VN DC mA24 340 7036 780 4672 3200 23110 9700 11

Types with LED indicator take additional 5 10 mA @ < 80 V

InsulationPulse (1.2 / 50 us / Dielectric strength (V rms, 1 minute)Contact / coil / 2.5 kVContact / contact / 2.5 kVContact open / 1.5 kV

General SpecificationsAmbient temperature operation / storage -40 +70 C / -40 +85 CPick-up time typ. 12 msRelease time typ. 20 msBounce time NO contact typ. 3.5 msMechanical life 108 operationsOperating frequency at nominal load 360 operations / hIngress protection rating IP 40Weight 80 g

Standard types

DC: 24, 36, 72, 110 V C31D/R DCV

"" Enter the voltage for full type designation

AccessoriesSocket: C11A, C12B0

Technical approvals, conformities

See table on page 53.

Connection diagram

Fig. 1 AC voltage endurance

Fig. 2 DC load limit curve

Dimensions [mm]

0.10 50 100 150 200 250

0.2

0.3

0.5

1

2

34

68

10

Cur

rent

[A]

Voltage [V]

DC-1L/R 40 ms

Cyc

les

Switching current [A]

AC-1107

106

1050 1 2 3 4 5 6 7 8 9 10

1131A2

34

24

32

2122

12

14

A11

23

4567

8

910

11

35

35

51

141234

111

242275

216

343298

3111

2A1 (+)

A210


1

Rela

ys

Long life series with twin contacts

C32D/R11 pin plug-in relay, 3-pole, change-over twin contacts, according to IEC 60067

Type: C32D/R VLong Life Relays for Railway application, 3 change-over twin contactsTypes with LED status indicatorTypes with free wheeling diodeManual actuator and mech. status indicator

Maximum contact load 6 A / 250 V AC-1 6 A / 30 V DC-1Recommended minimum contact load 10 mA / 5 V

ContactsType twin contact micro disconnectionMaterial AgCuNiRated current 6 AInrush current max. (20 ms) 15 ASwitching voltage AC-1 max. 250 VAC load max. 1500 VA AC-1DC load max. see Fig. 2

Coils (Values are valid at 20 C)Operating voltage range 0.7 1.25 UNNominal power DC 1.2 W

Coil Table VN DC mA24 340 7036 780 46110 9700 11

Types with LED indicator take additional 5 10 mA @ < 80 V

InsulationPulse (1.2 / 50 us / Dielectric strength (V rms, 1 minute)Contact / coil / 2.5 kVContact / contact / 2.5 kVContact open / 1.5 kV

General SpecificationsAmbient temperature operation / storage -40 +70 C / -40 +85 CPick-up time typ. 12 msRelease time typ. 20 msBounce time NO contact typ. 3.5 msMechanical life 108 operationsOperating frequency at nominal load 360 operations / hIngress protection rating IP 40Weight 80 g

Standard types

DC: 24, 36, 110 V C32D/R DCV


AccessoriesSocket: C11A, C12B0



Connection diagram



Dimensions [mm]

0.10 50 100 150 200 250

0.2

0.3

0.5

1

2

3 4

6 810

Cur

rent

[ A]

Voltage [V]

DC-1L/R 40 ms

Cyc

les


AC-1107

1060 1 2 3 4 5 6

1131A2

34

24

32

2122

12

14

A11

23

4567

8

910

11

35

35

51

2A1 (+)

A210

1412

11

34

1

2422

21

75

6

343298

3111


Standard Relays

R3-N311-pin plug-in relay, 3-pole, change-over contacts, according to IEC 60067

Type: R3-Nxx/VRelays for Railway application, 3 change-over contacts

Maximum contact load 6 A / 250 V AC-1, 6 A / 30 V DC-1Recommended minimum contact load 10 mA / 10 V Code 4 5 mA / 5 V Code 8

ContactsMaterial Optional Code 4 AgNi +0.2 Au Optional Code 8 AgNi +10 AuRated current 6 AInrush current max. (20 ms) 15 ASwitching voltage AC-1 max. 250 VAC load max. see Fig. 1DC load max. see Fig. 2

Coil (Values are valid at 20 C)Coil resistance see table; tolerance 10 %Operating voltage range 0.7 1.25 UNNominal power 1.1 W

Coil Table V DC mA

24 525 4648 2133 2272 4844 15110 12900 9

InsulationPulse (1.2 / 50 us / Dielectric strength (V rms, 1 minute)Contact / coil 4 kV / 2.5 kVContact / contact 4 kV / 2.5 kVContact open 1.5 kV / 1 kV

SpecificationsAmbient temperature operation / storage -25 (no ice) +70 C / -40 +80 CPick-up time / bounce time 18 ms / 3 msRelease time / bounce time (D version) 35 ms / 1 msMechanical life > 10 millionsIngress protection rating IP 40Weight 95 g

Standard types

DC: 24, 48, 72, 110 V R3-N34/DCV R3-N38/DCVFree wheeling diode R3-N34D/DCV R3-N38D/DCVLED R3-N34X/DCV R3-N38X/DCVLED + free wheeling diode R3-N34DX/DCV R3-N38DX/DCV*

"..." Enter the voltage for full type designation

Accessories Socket: C11A, C12B0Optional accessories (blanking plug): SO-NP, SO-OP



Connection diagram



Dimensions [mm]

0 50 100 150 200 2500.1

0.2

0.3

0.5

2

34

6

1

Cur

rent

[ A]

Voltage [V]

DC-1L/R 40 ms

Cyc

les

Switching current [A]0 1 2 3 4 5 6

AC-1cos phi 0.4

107

106

105

58.5

35

35

A2 A1

7

8

9

11

65

4

3

21

10

11

12 14

21

22 24 32 34

31

987534

1161

2A1 (+)

A2

10


1

Rela

ys

Type: R4-A4xx/VRelays for Railway application, 4 change-over contacts

Maximum contact load 6 A / 250 V AC-1, 0.5 A / 110 V DC-1 6 A / 30 V DC-1, 0.2 A / 220 V DC-1Recommended minimum contact load 10 mA / 10 V Code 4 5 mA / 5 V Code 8

ContactsMaterial Optional Code 4 AgNi + 0,2 Au Optional Code 8 AgNi + 10 AuRated current 6 AInrush current max. (20 ms) 18 A Switching voltage AC-1 max. 250 V AC load max. see Fig.1DC load max. see Fig. 2


Coil Table V DC mA

24 426 5636 881 4148 1500 3272 3456 21110 8231 13


SpecificationsAmbient temperature operation / storage -25 (no ice) +55 C / -40 +80 CPick-up time / bounce time 15 ms / 2 msRelease time / bounce time 20 ms / 2 msMechanical life > 20 millionsIngress protection rating IP40Weight 90 g

Standard types

DC: 24, 36, 48, 72, 110 V R4-A44/DCV R4-A48/DCVLED R4-A44X/DCV R4-A48X/DCVFree wheeling diode R4-A44DX/DCV R4-A48DX/DCVPolarity and free wheeling diode R4-A44FX/DCV R4-A48FX/DCV


Accessories Socket: CS-144Optional accessories (blanking plug): SO-NP, SO-OP

Standard Relays

R4-A414-pin plug-in relay, 4-pole, change-over contacts



Connection diagram



Dimensions [mm]

Cur

rent

[ A]

Voltage [V]0 50 100 150 200 250

0.1

0.2

0.3

0.5

1

3

2

4

6 DC-1L/R 40 ms

Cyc

les


107

106

1050 1 2 3 4 5 6

AC-1cos phi 0.4

52.5

35

35

3

12

45

78

1011

96

123

1413

1241

10 114442

11

12 14

21

22 24 32 34

31

875421

963

13A1 (+)

A2

14


Miniature relays

R7-A28-pin plug-in miniature relay, 2-pole, change-over contacts

Type: R7-A2x/VRelays for Railway application, sensitive, 2 change-over contacts

Maximum contact load: 10 A / 250 V AC-1, 10 A / 30 V DC-1Recommended minimum contact load 10 mA / 10 V Code 4 5 mA / 5 V Code 8

ContactsMaterial Optional Code 4 AgNi + 0.2 Au Optional Code 8 AgNi + 10 AuRated current 10 AInrush current max. (20 ms) 30 ASwitching voltage AC-1 max. 250 VAC load max. see Fig. 1DC load max. see Fig. 2


Coil Table V DC 10% mA24 535 4548 2004 2472 4750 15110 11337 10


SpecificationsAmbient temperature operation / storage -25 (no ice) +70 C / -40 +80 CNumber of mechanical operations > 20 millionsPick-up time typ. 10 msRelease time typ. 15 msIngress protection rating IP40Weight 35 g

Standard types

DC: 24, 48, 72, 110 V R7-A24/DCV R7-A28/DCVLED: R7-A24X/DCV R7-A28X/DCVFree wheeling diode: R7-A24D/DCV R7-A28D/DCVLED + free wheeling diode: R7-A24DX/DCV R7-A28DX/DCV


Accessories Socket: CS-118

Connection diagram



Dimensions [mm]



Cur

rent

[ A]

Voltage [V]

10

0 50 100 150 200 2500.1

0.2

0.3

0.5

1

2

3468 DC-1

L/R 40 ms

AC-1cos phi 0.4

Cyc

les


107

106

1050 1 2 3 4 5 6 7 8 9 10

3

57A

8B

1

4

6

2

21

4.75

37.5 28

11

12 14 22 24

21

4231

65

7A1(+)

A2

8


1

Rela

ys

Connection diagram



Dimensions [mm]



Miniature relays

R7-T28-pin plug-in miniature relay, 2-pole, change-over twin contacts

Type: R7-T2x/VRelays for Railway application, 2 change-over twin contacts

Maximum contact load 6 A / 250 V AC-1, 6 A / 30 V DC-1Recommended minimum contact load 5 mA / 5 V Code 1 1 mA / 5 V Code 2

ContactsMaterial Standard Code 1 AgNi + 0.2 Au Optional Code 2 AgNi + 10 AuRated current 6 AInrush current max. (20 ms) 15 ASwitching voltage AC-1 max. 250 VAC load max. see Fig. 1DC load max. see Fig. 2

Coil (Values are valid at 20 C)Coil resistance see table; tolerance 10 % Operating voltage range 0.7 1.25 UNNominal power 1.1 W

Coil Table V DC 10% mA24 535 4548 2004 2472 4750 15110 11337 10


SpecificationsAmbient temperature operation / storage -25 (no ice) +70 C / -40 +80 CNumber of mechanical operations > 20 millionsPick-up time typ. 10 msRelease time typ. 15 msIngress protection rating IP40Weight 35 g

Standard types

DC: 24, 48, 72, 110 V R7-T21/DCV R7-T22/DCVLED: R7-T21X/DCV R7-T22X/DCVFree wheeling diode: R7-T21D/DCV R7-T22D/DCVLED + free wheeling diode: R7-T21DX/DCV R7-T22DX/DCV


Accessories Socket: CS-118

DC-1L/R 40 ms

Cur

rent

[ A]

Voltage [V]0 50 100 150 200 250

0.1

0.2

0.3

0.5

1

2

34

6

AC-1

Cyc

les


107

106

1050 1 2 3 4 5 6

3

57A

8B

1

4

6

2

21

4.75

37.5 28

4231

65

7A1(+)

A2

811

12 14

21

22 24


Interface relays 6.2 mm

CINT-21Interface module with mechanical change-over output contact,DIN rail mounting

Connection diagram



Dimensions [mm]



TS35

12

11

14

A1

A2

6,2 733,4

93,5

44,3

49,2

Connector bridgeCINT-BR20

Label includedCINT-BR8

14

11

12

A1

A2

SOCKET

RELAY

Types: CINT-21/VStandard interface module, 1 change-over contactCage clamp terminalControl voltage UC 24 V, 50/60 HzGreen LED for status indication

Max. contact load 6 A / 250 V AC-1

Contact DataType micro disconnectionMaterial AgSnO2Rated current 6 AInrush current max. (5 ms) 30 ASwitching voltage AC-1 max. 250 VAC load max. 1500 VADC load max. see Fig. 2Recommended min. contact load 10 mA / 12 V

Control input Vn = UC 24 VOperating voltage range 16.3 30 VTypical input current 11 mANominal power consumption 260 mW

InsulationPulse (1.2 / 50 us / Dielectric strength (V rms, 1 minute)Contact / coil 6 kV / 4 kVContact open 1.5 kV / 1 kV

General SpecificationsAmbient temperature operation / storage -40 +70 C / -40 +85 CTypical response time @ Vn 5 msTypical release time @ Vn 10 msService life mech. / elec. 107 / 105 operationsCond. cross section cage clamp terminal stranded wire 0.5 1.5 mm2

Ingress protection rating IP 20Mounting position anyHousing material Polyamid

Standard types

UC 24 (AC/DC): CINT-21/UC24V

AccessoriesPlug-in bridges: CINT-BR20 (2 x 10 pin)Label plate: CINT-BEZ/64 (64 pieces)Replacement relay for CINT-21: CINT-R1/DC24V

0.1

0.2

0.3

0.5

1

2

5 6

0 50 100 150 200 250

Cur

rent

[A]

Voltage [V]

DC-1

107

106

105

1040 1 2 3 4 5 6

Cyc

les


AC-1


1

Rela

ys



Connection diagram



Dimensions [mm]



TS35

12

11

14

A1

A2

6,2 733,4

93,5

44,3

49,2



14

11

12

A1

A2

SOCKET

RELAY

Types: CINT-22/UC24VStandard interface module, 1 change-over contactCage clamp terminalControl voltage UC 24 V, 50/60 HzGreen LED for status indication


Contact DataType micro disconnectionMaterial AgNi +5AuRated current 6 AInrush current max. (20 ms) 10 ASwitching voltage AC-1 max. 250 VAC load max. 1500 VADC load max. see Fig. 2Recommended min. contact load 1 mA / 1 V





Standard types



0.1

0.2

0.3

0.5

1

2

5 6

0 50 100 150 200 250

Cur

rent

[A]

Voltage [V]

DC-1

107

106

105

1040 1 2 3 4 5 6

Cyc

les


AC-1



CINT-25Interface module with solide state DC output,DIN rail mounting

Connection diagram



Dimensions [mm]

TS35

12

11

14

A1

A2

6,2 733,4

93,5

44,3

49,2



14

11

12

A1

A2

SOCKET

RELAY

(+)

Types: CINT-25/UC24VStandard interface module, Solide state DCCage clamp terminalControl voltage UC 24 V, 50/60 HzGreen LED for status indication

Max. contact load 2 A / 24 V DC-1

Contact DataType micro disconnectionMaterial Solide stateRated current 2 AInrush current max. (10 ms) 20 ASwitching voltage DC-1 max. 30 VDC load max. 48 WRecommended min. contact load 1 mA, 6 V


InsulationPulse (1.2 / 50 us / Dielectric strength (V rms, 1 minute)Input / output / 2.5 kV

General SpecificationsAmbient temperature operation / storage -40 +55 C / -40 +85 CTypical response time @ Vn 1 msTypical release time @ Vn 1 msCond. cross section cage clamp terminal stranded wire 0.5 1.5 mm2


Standard types




1

Rela

ys

Interface relays 14 mm


Connection diagram



Dimensions [mm]



SOCKET

242122141112A1

A2

RELAY

REL

AYS

A1

A2

220-240VU

24 14NO

21 11COM

22 12NC

TS35

14 723,4

93

4845



Contact DataType micro disconnectionMaterial AgSnO2Rated current 10 A / (16 A*)Inrush current max. (5 ms) 80 ASwitching voltage AC-1 max. 250 VAC load max. 4000 VADC load max. see Fig. 2Recommended min. contact load 10 mA, 24 V* For currents > 10 A, contact terminals must be connected in parallel (21 with 11, 24 with 14, 22 with 12)





Standard types


AccessoriesPlug-in bridges: CINT-BR8/5 (5 pieces x 8 pin)Label plate: CINT5-BEZ/18 (18 pieces)Replacement relay for CINT-61: CINT-R21/DC24V

0.10 50 100 150 200 250

0.2 0.3

0.5

1

2

5

101610

Cur

rent

[A]

Voltage [V]

DC-1

0 2 4 6 8 10 12 14 16

Cyc

les


AC-1107

106

105

104



CINT-62Interface module with 2 mechanical change-over output contacts,DIN rail mounting



Contact DataType micro disconnectionMaterial AgNi +5AuRated current 8 AInrush current max. (20 ms) 15 ASwitching voltage AC-1 max. 250 VAC load max. 2000 VADC load max. see Fig. 2Recommended min. contact load 5 mA / 5 V


InsulationPulse (1.2 / 50 us / Dielectric strength (V rms, 1 minute)Contact / coil 6 kV / 4 kVContact / contact 4 kV / 2 kVContact open 1.5 kV / 1 kV

General SpecificationsAmbient temperature operation / storage -40 +70 C / -40 +85 CTypical response time @ Vn 5 msTypical release time @ Vn 10 msService life mech. / elec. 107 / 105 operationsCond. cross section spring cage stranded wire 0.5 1.5 mm2


Standard types



Connection diagram



Dimensions [mm]



SOCKET

242122141112A1

A2

RELAY

REL

AYS

A1

A2

220-240VU

24 14NO

21 11COM

22 12NC

TS35

14 723,4

93

4845

0.1

0.2

0.3

0.5

1

2

5

810

0 50 100 150 200 250

Cur

rent

[A]

Voltage [V]

DC-1

0 1 2 3 4 5 6 7 8

Cyc

les


AC-1107

106

105

104


1

Rela

ys


CINT-63Interface module with 2 mechanical change-over output contacts,DIN rail mounting



Contact DataType micro disconnectionMaterial AgNiRated current 8 AInrush current max. (20 ms) 15 ASwitching voltage AC-1 max. 250 VAC load max. 2000 VADC load max. see Fig. 2Recommended min. contact load 10 mA / 24 V


InsulationPulse (1.2 / 50 us / Dielectric strength (V rms, 1 minute)Contact / coil 6 kV / 4 kVContact / contact 4 kV / 2 kVContact open 1.5 kV / 1 kV



Standard types



Connection diagram



Dimensions [mm]



SOCKET

242122141112A1

A2

RELAY

REL

AYS

A1

A2

220-240VU

24 14NO

21 11COM

22 12NC

TS35

14 723,4

93

4845

0.1

0.2

0.3

0.5

1

2

5

810

0 50 100 150 200 250

Cur

rent

[A]

Voltage [V]

DC-1

0 1 2 3 4 5 6 7 8

Cyc

les


AC-1107

106

105

104


Signal relays

C203.06RInterface module with 2 mechanical change-over twin contacts,DIN rail mounting

Types: 203.06R/VStandard interface module, 2 separate change-over contactsScrew terminalsControl voltage UC 24 or 36 V, 50/60 HzLED status indicator for each channelSealed relays built inAlso suitable for panel mounting 2 x M4

Max. contact load 2 A / 30 V DC-1

Contact DataType twin contactsMaterial Ag +AuRated current 2 ASwitching voltage AC-1 max. 125 VAC load max. 100 VADC load max. see Fig. 2Recommended min. contact load 10 A / 10 mV

Control input Vn = UC 24 V UC 36 VOperating voltage range 16.8 30 V 25.2 45 VTypical input current 18 mA 9 mANominal power consumption (per channel) 220 mW 330 mW

InsulationContact / Coil 2.5 kVrms 1 minute

General SpecificationsAmbient temperature operation / storage -40 +70 C / -40 +85 CTypical response time @ Vn 10 msTypical release time @ Vn 20 msService life mech. / elec. 107 / 105 operationsCond. cross section screw terminal stranded wire 2.5 mm2, 2 x 1.5 mm2

Ingress protection rating IP 20Max. screw torque 0.4 NmMounting position anyHousing material LexanWeight 80 g

Standard types

UC (AC DC): 24, 36 V C203.06R/UCV


AccessoriesLabel plate: BZS-DIN17.5

Connection diagram



Dimensions [mm]


Fig. 1 DC voltage endurance

TS

35

5 64

752,

5

17,54,2

LABEL

A1 A1 A2

11 12 14

11 12 14

1 2

1

2

0.1

0.2

0.3

0.5

1

2

0 50 100 150

Cur

rent

[A]

Voltage [V]

DC-1

0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 2

Cyc

les


DC-1 30V 106

105


1

Rela

ys

Connection diagram

Coil circuit



Dimensions [mm]

Fig. 1 DC load limit curve DC-1

Power relays

RIC20-20 A, AC/DC control voltage, silent operation,DIN rail mounting according to DIN 43 880

Type: RIC20-xxx/VHum-free installation contactor, 2 contacts, 2 NO, 1 NO-1 NC, 2 NC types available

Rated operational power 4 kW / 230 V AC-1, 0.5 A / 220 V DC-1Recommended minimum contact load 10 mA / 24 V

ContactsMaterial AgNiRated current 20 AInrush current max. (100 ms) 50 ASwitching voltage AC-1 max. 400 VAC load max. AC-1, AC-7a 4 kW / 230 V AC-3 1.3 kW /230 V (NO contact only)DC load max. see Fig. 1

Control input Vn = UC 24 V UC 36 V UC 230 VOperating voltage range [V] 20.4 26.4 30.6 39.6 195 253Typ. pic up voltage [V] 17 25 160Typ. release voltage [V] 7 11 70Power consumption [W] 2.5 2.5 2.5Inductive turn-off voltage None None NoneSurge immunity EN 61000-4-5 2 kV 2 kV 2 kV

InsulationRated insulation voltage 230 VRated impulse withstand voltage 4 kVMin. clearance of open contact 3.6 mm

General SpecificationsAmbient temperature storage -30 +80 Coperation, Spacer after 2 contactors side by side -5 +55 C operation, Spacer after 3 contactors side by side -5 +40 CPick-up time 15 45 msRelease time 20 50 msMechanical life 3 x 106 operationsAC voltage endurance at rated load AC-3, AC-7b 3 x 105 operationsDC voltage endurance at rated load DC-1 105 operationsOperating frequency at rated load DC-1 300 operations / hOperating frequency at rated load AC-1 600 operations / hConductor cross section coil /contacts Stranded wire 2.5 mm2 / 6 mm2

Max. Screw torque coil / contacts 0.6 Nm / 1.2 NmIngress protection rating IP 20Weight 140 g

Standard types

UC (AC/DC) 50/60 Hz: 24, 36, 230 V 2NO: RIC20-200/UC V1NO + 1NC: RIC20-110/UC V

"" Enter the voltage for full type designation 2NC: RIC20-020/UC V

AccessoriesAuxiliary contact bloc: RIC-AUX RIC25, 40, 63Sealing cover: RIC-SEAL20Spacer: RIC-DIST

Samples of lamp loads Number of lampsIncandescent lamps 230 V / 100 W 20Fluorescent lamps not corrected 230 V / 36 W 17Fluorescent lamps electronic ballast units 36 W 15

TS35

85

17,5

45

44 (45.5*) 16.55

1.5*

*Option:Sealing coverType: RIC-SEAL20

Mounting informationIf multiple contactors are mounted side by side, spacers (RIC DIST) have to be inserted for the purpose of heat dissipation.

Example: Ambient temperature up to 40C: 1 spacer after 3 RIC // 4055C: 1 spacer after 2 RIC.

1 A1 3

2 A2 4

1 A1 R1

2 A2 R2

R1 A1 R3

R2 A2 R4

2x NORIC20-200

2x NCRIC20-020

1x NO + 1x NCRIC20-110

A1U

A2

DC-1DC-3DC-5

Voltage [V]0 50 100 150 200 250

Cur

rent

[A]

20

10

5

2

1

0.5

0.2

0.1

0.05


Power relays

RIC25-25 A, AC/DC control voltage, silent operationDIN Rail mounting according to DIN 43 880

Type: RIC25-xxx/VHum-free installation contactor, 4 contacts, 4 NO, 4 NC, 2 NO-2 NC types available

Rated operational power AC-1 Single phase: 5.4 kW/230 V, 0.5 A/220 V DC-1 3 phase 230 V: 9 kW 3 phase 400 V: 16 kWRecommended minimum contact load 10 mA / 24 V

ContactsMaterial AgNiRated current 25 AInrush current max. (100 ms) 50 ASwitching voltage AC-1 max. 400 VAC load max. AC-1, AC-7a 4 kW / 230 V AC-3 2.2 kW /230 V, 4 kW / 400 VDC load max. see Fig. 1

Control input Vn = UC 24 V UC 36 V UC 230 VOperating voltage range [V] 20.4 26.4 30.6 39.6 195 253Typ. pic up voltage [V] 17 25 160Typ. release voltage [V] 7 11 70Power consumption [W] 3 3 3Inductive turn-off voltage None None NoneSurge immunity EN 61000-4-5 2 kV 2 kV 2 kV

InsulationRated insulation voltage 440 VRated impulse withstand voltage 4 KVMin. clearance of open contact 3.6 mm

General SpecificationsAmbient temperaturestorage -30 +80 Coperation, Spacer after 2 contactors side by side -5 +55 Coperation, Spacer after 3 contactors side by side -5 +40 CPick-up time 15 45 ms Release time 20 70 msMechanical life 3 x 106 operationsAC voltage endurance at rated load AC-3, AC-7b 5 x 105 operationsDC voltage endurance at rated load DC-1 105 operations Operating frequency at rated load DC-1 300 operations / hOperating frequency at rated load AC-1, AC-3 600 operations / hConductor cross section coil / contacts terminals Stranded wire 2.5 mm2 / 6 mm2

Max. Screw torque coil / contacts 0.6 Nm / 1.2 Nm Ingress protection rating IP 20Weight 270 g

Standard types

UC (AC/DC) 50/60 Hz: 24, 36, 230 V 4NO: RIC25-400/UCV

2NO + 2NC: RIC25-220/UCV"" Enter the voltage for full type designation 4NC: RIC25-040/UCV

AccessoriesAuxillary contact bloc: RIC-AUXSealing cover: RIC-SEAL25Spacer: RIC-DIST

Samples of lamp loads Number of lampsIncandescent lamps 230 V/ 100 W 20Fluorescent lamps not corrected 230 V/ 36 W 20Fluorescent lamps electronic ballast units 36 W 20

TS35

45

44 (45.5*) 16.5535

85

1.5*

*Option:Sealing coverType: RIC-SEAL25

Mounting informationIf multiple contactors are mounted side by side, spacers (RIC DIST) have to be inserted for the purpose of heat dissipation.

Example: Ambient temperature up to 40C: 1 spacer after 3 RIC // 4055C: 1 spacer after 2 RIC.

Connection diagram

Coil circuit



Dimensions [mm]

Fig. 1 DC load limit curve DC-1

A1U

A2

4x NC: RIC25-040 R2 R4 A2 R6 R8

R1 R3 A1 R5 R7

2x NO + 2x NC: RIC25-220 2 R2 A2 R4 4

1 R1 A1 R3 3

4x NO: RIC25-400

2 4 A2 6 8

1 3 A1 5 7

DC-1DC-3DC-5

0 50 100 150 200 250

Voltage [V]

25

1510

5

2

1

0.5

0.2

0.1

Cur

rent

[A]


2

Tim

e Re

lays

2. Time Relays

Application Types Functions* t min. max. Output contacts Design

Time relay with mechanical CO output contact CIM1R E, A, W, N, K, B, B1, S, LS 50 ms 60 h 16 A 250 V

Time relay with AC solide-state output CIM12R E, A, W, N, K, B, B1, S, LS 50 ms 60 h 2 A 250 V

Time relay with DC solide-state output CIM13R E, A, W, N, K, B, B1, S, LS 50 ms 60 h 5 A 24 VD

Time relay with mechanical CO output contact CIM2R E, A, L, M, B2, G, H 50 ms 60 h 16 A 250 V

Time relay with AC solide-state output CIM22R E, A, L, M, B2, G, H 50 ms 60 h 2A 250V

Time relay with AC solide-state output CIM23R E, A, L, M, B2, G, H 50 ms 60 h 5A 24VD

Time relay with mechanical CO output contact CIM3R F, Q, G, H, I, P 50 ms 60 h 16A 250V

Time relay with AC solide-state output CIM32R F, Q, G, H, I, P 50 ms 60 h 2A 250V

Time relay with DC solide-state output CIM33R F, Q, G, H, I, P 50 ms 60 h 5 A 24 VD

Modular time relay with power CO output contacts CT32.31 E, A, W, N, K, B, B1 0.15 s 60 min 10 A

Modular time relay with 3 twin CO output contacts CT32.32 E, A, W, N, K, B, B1 0.15 s 60 min 6 A

Modular time relay with power CO output contacts CT33.31 E, A, F, W, N, Q, K, L, B, B1, G, H 30 ms 60 h 10 A

Modular time relay with 3 twin CO output contacts CT33.32 E, A, F, W, N, Q, K, L, B, B1, G, H 30 ms 60 h 6 A

Modular time relay with power CO output contacts CT36.31 I, P 2x 50 ms 60 h 10 A

Modular time relay with 3 twin CO output contacts CT36.32 I, P 2x 50 ms 60 h 6 A

*Function diagrams: refer to page 20

TF-60 Setting of long timesThe TF60 time setting methode permits short exami-nation of long delay time settings. Elapsing times of hours can be monitored in the sec. range.

Example for a delay time of 38h:1. Set range switch to 60sec2. Set 38sec on the potentiometer (e.g. check 38sec by chronometer)3. Set range switch to 60hThe delay time now amounts to 38h.


Delay functions Shot timing modes

A

RS

t

Et R

S

Ft1 t2 R

S

S R on with delaySOFF R off

S R onSOFF R off with delay

S R on with delay (t1)SOFF R off with delay (t2)

On delay

Off delay

On and off delay

W

RS

t

N

RS

t

RSO

t1 t2

S R on for tSOFF R off(pulse clipping)

SOFF R on for tS on for t R off

S R on for t1SOFF R on for t2SOFF off for t1 R off

One shot leading edge

One shot trailing edge

One shot leading and trailing edge

B2

RS

t t t

K

RS

t

L

RS

t

M

RS

t

B

RS

t tt

B1

RS

t tt

Puls shaping Blinker functions

S (pulse or continuous contact) R on for t

S no influence on R and t

S R on/off periodicallyaccording to tSOFF R off

S (pulse or continuous contact) R on for t

S on for t = tRESET

S R on/off periodicallyaccording to tSOFF: last pulse = t

SOFF R on for tS no influence on R and t

S R after t on/off periodicallyaccording to tSOFF R off

Puls shaping

Pulse shaping, retrigger (subsequ.time operation from 0)

Puls shaping

Blinker, pulse start

Blinker, pulse start, trailing pulse

Blinker, interval start

G

RS

t1 t2

H

RS

t1 t2

I

RS

t1 t1t2

P

RS

t1 t1t2

C55, CT1: t2 t1

Delayed pulse Repeat cycle timer

S (pulse or continuous contact) R after t1 on for t2

S no influence on R and t

S R on/off periodicallyaccording to t1 and t2SOFF R off

S R after t1 on for t2SOFF R off

S R after t1 (t2) on/off peri- odically according to t2 and t1SOFF R off

On delay single shot

On delay single shot

Repeat cycle timer, pulse start

Repeat cycle timer, interval start

X1

RS

t t

S

RS

LS

RS

t t

Y St

t

Special functions Special functions

S R onSOFF R off and starts tS R restart only after t

S R on and starts tS on for t R off

S R on/offS on for tOFF on with delay for t -

SOFF off

Star-delta timer

Restart delay

Step-on /Step-off switch

Step-switching (staircase lighting timer), with time lapse

t STOP T

tRESET

S = TriggeringR = Output circuit

= switches

Stop/ResetSSTOP interrupts t(t-addition)

SRESET reset tt restarts immediately

t is stopped R on/off

TestON OFF

Time functions


2

Tim

e Re

lays

Multifunction Timer, DIN Rail mounting

CIM1R Time relay with mechanical change-over output contact 8 time functions + stepping function, ON-OFF switch, 50 ms 60 h

Type: CIM1R/UC24-240VSophisticated multifunction time relay, 1 change-over power contact with zero crossing switching (50/60 Hz), 8 time functions, stepping function and service function ON/OFF, time ranges: 50 ms 60 h, multifunction LED state indicator, suitable for any time-control application and also staircase lighting, Light-switch neon lamp current absorption on input B1, Manual switching function for maintenance, emergency, etc., 16.6 Hz power supply applications. Railway version available.

Maximum contact load 16 A / 250 V AC-1Recommended minimum contact load 10 mA / 10 V

Time functions and related connection diagrams (Function diagrams: refer to page 20)The functions are selectable by rotary switch

LED function table:

E

B W

A K N S LSB1A1

S

A2B1A1 A2

S

A1 B1 A2

S

LED Relay Time run

OFF OFF NO

Continuous ON ON NO

Short blinking OFF YES

Long blinking ON YES

Time data7 partial time ranges, tmax (rotary switch) 0.6, 6, 60 s / 6, 60 min / 6, 60 hFine adjustment range (rotary knob) tmin tmax, 0.5 6Time range tolerance tmin: -5 % +0 % / tmax: -0 % +5 %Repetition accuracy 0.1 % or DC: 2 ms / AC: 10 msResponse time, power on, on A1 45 msMin. trigger pulse on B1 20 ms (AC / DC)Reset time B1 (AC/DC) 40 msVoltage failure buffering (50 / 60 Hz) 20 ms

ContactsType AgNi / 1 CO, micro disconnectionRated operational current at 40 C / 60 C 16 A / 13 A Max. inrush current (10 ms) 30 AMax. switching voltage AC-1 250 V Max. AC load AC-1 (Fig.1) 4 kVAMax. DC load DC-1 see Fig. 2

Power supply- and control inputNominal voltage (A1, B1) UC 24-240 V (UC = AC/DC)Operating voltage range UC 16.8 250 VPower consumption approx. 0.5 WFrequency range 16 63 HzAllowed DC residual current into B1 0.5 mAAC Neon lamp residual current into B1 10 mATrigger threshold voltage on B1, AC / DC 13 / 15 V

InsulationTest voltage open contact 1 kVrms 1 minuteTest voltage between contacts and control input 2.5 kVrms 1 minute

General SpecificationsAmbient temperature storage / operation -40 +85 C / -40 +70 CMechanical life of contact 30 x 106 operationsConductor cross section Stranded wire 2.5 mm2, 2 x 1.5 mm2

Ingress protection rating IP 20Max. Screw torque 0.4 NmHousing material LexanWeight 70 g

Standard types

UC (AC/DC) 1560 Hz CIM1R/UC24-240V

752,

5

17,54,2

45

TS

35

5 44 20



Connection diagram



Dimensions [mm]

0.1

0.2

0.5

1

2

5

10

1620

0 50 100 150 200 250 300

Cur

rent

[ A]

Voltage [V]

DC-1

Cyc

les


AC-1107

106

1050 2 4 6 8 10 12 14 16



CIM12RTime relay with AC solid-state output8 time functions and stepping function, ON-OFF switch, 50 ms 60 h

Type: CIMR12R/UC24-240VSophisticated multifunction time relay, 1 triac output, suitable for high frequency of operations and inductive loads, 8 time functions, stepping function and service function ON/OFF, time ranges: 50 ms 60 h, multifunction LED state indicator, suitable for any time-control application and also staircase lighting, Light-switch neon lamp current absorption on input B1, manual switching function for maintenance, emergency, etc., 16.6 Hz applications. Railway version available.

Maximum contact load 2 A / 250 V Minimum contact load 50 mA


LED function table:

E

B W

A K N S LSB1A1

S

A2B1A1 A2

S

A1 B1 A2

S

LED Relay Time run

OFF OFF NO

Continuous ON ON NO



Time data7 partial time ranges, tmax (rotary switch) 0.6, 6, 60 s / 6, 60 min / 6, 60 h Fine adjustment range (rotary knob) tmin tmax, 0.5 6Time range tolerance tmin: -5 % +0 % / tmax: -0 % +5 %Repetition accuracy 0.1 % or DC: 2 ms / AC: 10 msResponse time, power on, on A1 45 msMin. trigger pulse on B1 20 ms (AC / DC)Reset time B1 (AC/DC) 40 msVoltage failure buffering (50 / 60 Hz) 20 ms

OutputType Triac, zero crossingRated operational current at 40 C (Fig.1) 2 AMax. inrush current (10 ms) 100 AMax. switching voltage 250 VMax. AC load AC-1 300 VAI2t value 78 A2sLeakage current < 1 mA

Power supply- and control inputNominal voltage UC 24-240 V (UC = AC/DC)Operating voltage range UC 16.8 250 VPower consumption approx. 0.5 WFrequency range 16 63 HzAllowed DC residual current into B1 0.5 mAAC Neon lamp residual current into B1 10 mATrigger threshold voltage on B1, AC / DC 13 / 15 V

InsulationTest voltage between output and control input 2.5 kVrms 1 minute

General SpecificationsAmbient temperature storage / operation -40 +85 C / -40 +70 CConductor cross section Stranded wire 2.5 mm2, 2 x 1.5 mm2


Standard types

UC (AC/DC), 1560 Hz CIM12R/UC24-240V

TRIAC

752,

5

17,54,2

45

TS

35

5 44 20



Connection diagram

Fig. 1 Output derating curve

Dimensions [mm]

0

1

2

0 10 20 30 40 50 60 70 80

Cur

rent

[A]

Temperature [C]


2

Tim

e Re

lays

752,

5

17,54,2

45

TS

35

5 44 20



Connection diagram


Dimensions [mm]


CIM13RTime relay with DC solid-state output8 time functions and stepping function, ON-OFF switch, 50 ms 60 h

Type: CIM13R/UC24-240VSophisticated multifunction time relay, 1 transistor output, 8 time functions, stepping function and service function ON/OFF, time ranges from 50 ms 60 h, multifunction LED state indicator, suitable for any time-control application and also staircase-light control, light-switch neon lamp current absorption on input B1, manual switching function for maintenance, emergency, etc., 16.6 Hz applications. Railway version available.

Maximum contact load 5 A / 30 VRecommended minimum contact load 1 mA


LED function table:

E

B W

A K N S LSB1A1

S

A2B1A1 A2

S

A1 B1 A2

S

LED Relay Time run

OFF OFF NO

Continuous ON ON NO




OutputType MOS FETRated operational current at 40 C (Fig.1) 5 A Max. inrush current (10 s) 40 AMax. switching voltage 30 V Leakage current < 10 A

Power supply- and control inputNominal voltage (UC = AC / DC) UC 24-240 V (UC = AC/DC)Operating voltage range UC 16.8 250 VPower consumption approx. 0.5 WFrequency range 16 63 HzAllowed DC residual current into B1 0.5 mAAC Neon lamp residual current into B1 10 mATrigger threshold voltage on B1, AC / DC 13 / 15 V




Standard types


MOSFET

0

1

2

3

4

5

6

0 10 20 30 40 50 60 70 80

Cur

rent

[A]

Temperature [C]


752,

5

17,54,2

45

TS

35

5 44 20



Connection diagram



Dimensions [mm]


CIM2RTime relay with mechanical change-over output contact 7 time functions and 7 time ranges from 50 ms 60 h

Type: CIM2R/UC24-240VSophisticated multifunction time relay, 1 change-over power contact switching in zero crossing (50/60 Hz), 7 time functions and service function ON/OFF, 7 time ranges from 50 ms to 60 h, multifunction LED state indicator, suitable for any time-control application, light-switch neon lamp current absorption on input B1, manual switching function for maintenance, emergency, etc., 16.6 Hz power supply applications. Railway version available.



LED function table:

E

B2 H

A L M GA1

S

A2B1A1 A2

S

A1 B1 A2

S

LED Relay Time run

OFF OFF NO

Continuous ON ON NO




ContactsType AgNi / 1 CO, micro disconnectionRated operational current at 40 C / 60 C 16 A / 13 A Max. inrush current (10 ms) 30 AMax. switching voltage AC-1 250 V Max. AC load AC-1 (Fig.1) 4 kVAMax. DC load DC-1 see Fig. 2

Power supply- and control inputNominal voltage (A1, B1) UC 24-240 V (UC = AC / DC)Operating voltage range UC 16.8 250 VPower consumption approx. 0.5 WFrequency range 16 63 HzAllowed DC residual current into B1 0.5 mAAC Neon lamp residual current into B1 10 mATrigger threshold voltage on B1, AC / DC 13 / 15 V




Standard types


0.1

0.2

0.5

1

2

5

10

1620

0 50 100 150 200 250 300

Cur

rent

[ A]

Voltage [V]

DC-1

Cyc

les


AC-1107

106

1050 2 4 6 8 10 12 14 16


2

Tim

e Re

lays

Type: CIM22R/UC24-240VSophisticated multifunction time relay, 1 triac output, suitable for high frequency of operations and inductive loads, 7 time functions and service function ON/OFF, 7 time ranges from 50 ms 60 h, multifunction LED state indicator, suitable for any time-control application light-switch neon lamp current absorption on input B1, manual switching function for maintenance, emergency, etc., 16.6 Hz applications. Railway version available.

Maximum contact load 2 A / 250 VMinimum contact load 50 mA


LED function table:

E

B2 H

A L M GA1

S

A2B1A1 A2

S

A1 B1 A2

S

LED Relay Time run

OFF OFF NO

Continuous ON ON NO





Power supply- and control inputNominal voltage UC 24-240 V (UC = AC / DC)Operating voltage range UC 16.8 250 VPower consumption approx. 0.5 WFrequency range 16 63 HzAllowed DC residual current into B1 0.5 mAAC Neon lamp residual current into B1 10 mATrigger threshold voltage on B1, AC / DC 13 / 15 V




Standard types



CIM22RTime relay with AC solid-state output 7 time functions and 7 time ranges 50 ms 60 h

TRIAC

752,

5

17,54,2

45

TS

35

5 44 20



Connection diagram


Dimensions [mm]

0

1

2

0 10 20 30 40 50 60 70 80

Cur

rent

[A]

Temperature [C]



CIM23RTime relay with DC solid-state output 7 time functions and 7 time ranges from 50 ms 60 h

Type: CIM23R/UC24-240VSophisticated multifunction time relay, 1 transistor output, 7 time functions and service function ON/OFF, 7 time ranges from 50 ms 60 h, multifunction LED state indicator suitable for any time-control application, light-switch neon lamp current absorption on input B1, manual switching function for maintenance, emergency, etc., 16.6 Hz applications. Railway version available.



LED function table:

E

B2 H

A L M GA1

S

A2B1A1 A2

S

A1 B1 A2

S

LED Relay Time run

OFF OFF NO

Continuous ON ON NO




OutputType MOS FETRated operational current at 40 C (Fig.1)) 5 AMax. inrush current (10 s) 40 AMax. switching voltage 30 VLeakage current < 10 A

Power supply- and control inputNominal voltage (UC = AC / DC) UC 24-240 V (UC = AC / DC)Operating voltage range UC 16.8 250 VPower consumption approx. 0.5 WFrequency range 16 63 HzAllowed DC residual current into B1 0.5 mAAC Neon lamp residual current into B1 10 mATrigger threshold voltage on B1, AC / DC 13 / 15 V




Standard types


752,

5

17,54,2

45

TS

35

5 44 20



Connection diagram


Dimensions [mm]

0

1

2

3

4

5

6

0 10 20 30 40 50 60 70 80

Cur

rent

[A]

Temperature [C]

MOSFET


2

Tim

e Re

lays


CIM3RTime relay with mechanical change-over output contact 6 time functions and service function, 7 time ranges from 50 ms60 h

Type: CIM3R/UC24-240VSophisticated multifunction time relay, 1 change-over power contact switching in zero crossing (50/60 Hz), 6 time functions and service function ON/OFF, 7 time ranges from 50 ms to 60 h, multifunction LED state indicator, suitable for any time-control application, light-switch neon lamp current absorption on input B1, manual switching function for maintenance, emergency, etc., 16.6 Hz power supply applications. Railway version available.



LED function table:

F Q G

H I PA1

S

A2B1 A1 B1 A2

S

LED Relay Time run

OFF OFF NO

Continuous ON ON NO




ContactsType AgNi / 1 CO, micro disconnectionRated operational current at 40 C / 60 C 16 A / 13 AMax. inrush current (10 ms) 30 AMax. switching voltage AC-1 250 VMax. AC load AC-1 (Fig.1) 4 kVAMax. DC load DC-1 see Fig. 2

Power supply- and control inputNominal voltage (A1, B1) UC 24-240 V (UC = AC / DC)Operating voltage range UC 16.8 250 VPower consumption approx. 0.5 WFrequency range 16 63 HzAllowed DC residual current into B1 0.5 mAAC Neon lamp residual current into B1 10 mATrigger threshold voltage on B1, AC / DC 13 / 15 V




Standard types


752,

5

17,54,2

45

TS

35

5 44 20



Connection diagram



Dimensions [mm]

0.1

0.2

0.5

1

2

5

10

1620

0 50 100 150 200 250 300

Cur

rent

[ A]

Voltage [V]

DC-1

Cyc

les


AC-1107

106

1050 2 4 6 8 10 12 14 16


Type: CIM32R/UC24-240VSophisticated multifunction time relay, 1 triac output, suitable for high frequency of operations and inductive loads, 6 time functions and service function ON/OFF, 7 time ranges from 50 ms 60 h, multifunction LED state indicator, suitable for any time-control application light-switch neon lamp current absorption on input B1, manual switching function for maintenance, emergency, etc., 16.6 Hz applications. Railway version available.

Maximum contact load 2 A / 250 VMinimum contact load 50 mA


LED function table:

F Q G

H I PA1

S

A2B1 A1 B1 A2

S

LED Relay Time run

OFF OFF NO

Continuous ON ON NO









Standard types



CIM32RTime relay with AC solid-state output 6 time functions and service function, 7 time ranges from 50 ms60 h

0

1

2

0 10 20 30 40 50 60 70 80

Cur

rent

[A]

Temperature [C]

TRIAC

752,

5

17,54,2

45

TS

35

5 44 20



Connection diagram


Dimensions [mm]


2

Tim

e Re

lays

Type: CIM33/UC24-240VSophisticated multifunction time relay, 1 transistor output, 6 time functions and service function ON/OFF, 7 time ranges from 50 ms 60 h, Multifunction LED state indicator, suitable for any time-control application, light-switch neon lamp current absorption on input B1, manual switching function for maintenance emergency, etc., 16.6 Hz applications. Railway version available.



LED function table:

F Q G

H I PA1

S

A2B1 A1 B1 A2

S

LED Relay Time run

OFF OFF NO

Continuous ON ON NO




OutputType MOS FETRated operational current at 40 C (Fig.1) 5 AMax. inrush current (10 s) 40 AMax. switching voltage 30 VLeakage current < 10 A





Standard types



CIM33RTime relay with DC solid-state output 6 time functions and service function, 7 time ranges from 50 ms60 h

752,

5

17,54,2

45

TS

35

5 44 20



Connection diagram


Dimensions [mm]

MOSFET

0

1

2

3

4

5

6

0 10 20 30 40 50 60 70 80

Cur

rent

[A]

Temperature [C]


CT32R, CT33R, CT36R

Plug-in timer modules (to combine with industrial relays)

Type CT32R, CT33R, CT36R, /VPlug-in time modules for sockets with module slot in combination with plug-in relays.Power supply and control voltages 24 240 V. Time ranges 30 ms up to 60 h.LED output state indicator.



Dimensions [mm]

38 4 20 54

75

16

4

CT-System

Time functions and related connection diagrams (Function diagrams: refer to page 20)

CT32R (Universal) CT33R (Universal) CT36R (Repeat cycle timer)

Time dataType CT32R CT33R CT36RPartial time ranges, tmax 1.5, 6, 15, 60 /s /min 150, 600 ms 2 x 600 ms 1.5, 6, 15, 60 /s /min /h 2 x 6, 60 /s /min /hMin. time tmin 0.15 s 30 ms 2 x 50 msFine adj. range tmin 1 1 0 0.2 1 2 x 5 60Time range tolerance -25 0 % -25 0 % -25 0 % 0 25 % 0 25 % 0 25 %Repetition accuracy 0.2 % or 20 ms 0.2 % or 20 ms 0.2 % or 20 msTemperature drift of time 0.1 % / K 0.1 % / K 0.1 % / KMin. trigger pulse width B1 30 ms 30 ms Reset time pow. supply 150 ms 150 ms 150 msVoltage failure buffering 20 ms 20 ms 20 ms

Output dataNominal voltage UC 2448 VType Solid stateRated operational current 150 mAOn-state resistance 25 Leakage current 150 A

Power supply and control input (UC = AC/DC)Type CT32R CT33R CT36RNominal voltage UC 24 48 V UC 24 48 V UC 24 48 VOperating voltage range 16.8 60 V 16.8 60 V 16.8 60 VInput B1 inactive 9 V 9 V Supply current 5 11 mA 5 11 mA 6 12 mA

General SpecificationAmbient temperature storage / operation -40 +85 C / -40 +70 CIngress protection rating IP 40 when plugged inHousing material LexanWeight 25 g

Standard typesCT32R/UC24-48VCT33R/UC24-48VCT36R/UC24-48V

Remark: This module is part of several ready for connection units consisting of socket, relay and module. A wide range of suitable relays are available.


2

Tim

e Re

lays

CT32.31R, CT33.31R, CT36.31RCT32.32R, CT33.32R, CT36.32R

Plug-in timer set

S+

A1A2

S

+

A1A2 B1

S+

A1A2 B1

18

15

79 8 538 36 16

11 635

R

A1A210 2

+

3 4

12125

2628

B1TIMER

-MODUL

18

15

79 8 538 36 16

11 635

R

A1A210 2

+

3 4

12125

2628

B1

TIMER

-MODUL

E

CT32.31R/V

DC 24, 36V

CT32.32R/V

DC 24, 36V

CT33.31R/V

DC 24, 36V

CT33.32R/V

DC 24, 36V

CT36.31R/V

DC 24, 36V

CT36.32R/V

DC 24, 36V

MAX

MIN

0,15s-60min H0,15-1,5s6-60min

30ms-60h H30-150ms12-60h

2x50ms-60h H2x50-600ms5-60h

I P

E

A N K B1

W B

C31D/R C32D/R

10A 250VA 6A 250VA50mA 10V 10mA 5V

CT-System

Timer-Modul

Relay datas see: Relay C31; C32

Timer Delay Relay-SetRelay, Module and Socket

Triggering

Function (see page 30)

CT32R Universal-Timer

Timer RangeFunction/Triggering

CT33R Universal-Timer

CT36R Universal-Taktgeber

Timer RangeFunction/Triggering

Timer RangeE W H B

A N L F K G B1 Q

F Q G Ht2 = t1 t2 = 0,5s

Function/Triggering

7 functions, voltage controlled, time lapse display, blinking.Seismic approved.

12 functions, voltage controlled, time lapse display, blinking, high setting accuracy by dial graduation 1:5.

Pulse or pause start.t1/t2 separately settable.Time lapse display t1/t2.

Delivery includes: Relay C31D/R DCV Module CT32R/UC24-48V Front cover FS-C Socket C12B0 Retaining clip HF-32






Set Order-Nr.: Set Order-Nr.:



Universal Power Relay 10Awith 3 power change-over-contacts this is the robust relay for AC and DC circuits ranging from 50mA 10V.

Relay with 3 twin contacts 6AThe control relay with highest switching reliablility for controland signal circuits ranging from 10mA 5V.

Power Relay Control Relay

Set delivery includes: Relay Module Front cover Socket Retaining clip

Relay data:See page 4/5



Dimensions [mm]

See page 30.


Notes


3M

onito

ring

Rela

ys

3. Monitoring Relays

Application Types Monitoring Monitoring range Output contacts Design

Voltage monitoring, AC / DC single phase MRU11R 0 AC 480 V / DC 690 V

Voltage monitoring, AC / DC three phase MRU32R 0 AC 480 V / DC 690 V

Current monitoring, AC / DC single phase MRI11R 0 5 A

Current monitoring, AC / DC three phase MRI32R 0 5 A

Multifunction monitoring, AC / DC single phase MRM11R U, I, P, f, cos

Multifunction monitoring, AC / DC three phase MRM32R U, I, P, f, cos

DC Voltage monitoring CT524.31R 0 30 V

DC Voltage monitoring CT524.32R 0 30 V

DC Current monitoring CT512.31R 0 200 mA

DC Current monitoring CT512.32R 0 200 mA

DC Current monitoring CT515.31R 0 2 A




Isolation monitoring, DC networks ESU-D2 1 50 k 50mm


1-phase monitoring

MRU11RVoltage monitoring relay AC/DC, single phase DIN Rail mounting according to DIN 43 880

Type: MRU11R/VVoltage monitoring relay with over- and under voltage thresholds up to 690 V.Alarm delay setting. Alarm LED. Display for voltmeter function, alarm signaland interactive parameter setting.1 change-over alarm contact 6 A 250 V. Comfortable parameter setting.

Monitoring function

gnok fail alarm Alarm delay: tOFF, tON

ye rd

INPUT

al

ok

tON tOFF

AL

LIMIT 1HYST

alal

ok ok

tON tOFFtON tOFF

INPUT

AL

LIMIT 1HYST 1

HYSTLIMIT2

INPUT

al

ok

tON tOFF

AL

HYSTLIMIT1

Measuring circuit dataOver/under voltage setting ranges AC / DC 0 480 V / 0 690 VFrequency DC, AC 16 100 HzResolution 100 mVAccuracy 2 % 1 digitInput resistance 1 M

Time dataAlarm delay setting time 0.1 999.9 sReset time setting range 0.1 999.9 sVoltage failure buffering ca. 30 ms

Contacts Type / Material 1 CO / AgNi 0.15Rated operational current 6 AMax. inrush current 15 AMax. switching voltage 250 VMax. AC load AC-1 (Fig.1) 1250 VAMax. DC load DC-1, 24 V / 220 V (Fig.2) 120 W / 25 WRecommended min. contact load 10 mA / 10 V

Power supply UC12-48V UC110-240VNominal voltage AC/DC 12 48 V 110 240 VOperating voltage range 10 57 V 85 250 VAC frequency 16 63 Hz 16 63 HzPower consumption 2 W / 3 VA 2 W / 3 VA

InsulationTest voltage open - contact 1 kVrms 1 minuteTest voltage measuring input - contacts 4 kVrms 1 minuteTest voltage measuring input - power supply 4 kVrms 1 minute

General specificationsAmbient temperature storage /operation -40 +85 C / -25 +60 CMechanical life of contacts 30 x 106 operationsConductor cross section Stranded wire 2.5 mm2, 2 x 1.5 mm2

Ingress protection rating IP20Max. screw torque 0.4 NmHousing material Lexan EXL 9330Weight 130 g

Standard types

AC/DC 12-48 V, 1560 Hz MRU11R/UC12-48VAC/DC 110-240 V, 1560 Hz MRU11R/UC110-240V

A1 A2

15 16 18

U U U+

LOAD

AL

N L

Connection diagram

Fig. 1 AC voltage enduranc


Dimensions [mm]



0.10 50 100 150 200 250 300

0.2

0.3

0.5

1

2

56

10

Cur

rent

[A]

Voltage [V]

DC-1

Cyc

les


AC-1107

1050 1 2 3 4 5 6

106


3M

onito

ring

Rela

ys

Connection diagram



Dimensions [mm]



3-phase monitoring

MRU32RVoltage monitoring relay AC/DC, three phase DIN Rail mounting according to DIN 43 880

Type: MRU32R/VVoltage monitoring relay with over- and under voltage thresholds up to 690 V.Alarm delay setting. Alarm LED. Display for voltmeter function, alarm signaland interactive parameter setting.2 change-over alarm contacts 6 A 250 V. Comfortable parameter setting.

Monitoring function


ye rd

INPUT

al

ok

tON tOFF

AL

LIMIT 1HYST

alal

ok ok

tON tOFFtON tOFF

INPUT

AL

LIMIT 1HYST 1

HYSTLIMIT2

INPUT

al

ok

tON tOFF

AL

HYSTLIMIT1

Measuring circuit dataOver/under voltage setting ranges AC / DC 0 480 V / 0 690 VFrequency DC, AC 16 100 HzResolution 100 mVAccuracy 2 % 1 digitInput resistance 1 M


ContactsType / Material 2 CO / AgNi 0.15Rated operational current 6 AMax. inrush current 15 AMax. switching voltage 250 VMax. AC load AC-1 (Fig.1) 1250 VAMax. DC load DC-1, 24 V / 220 V (Fig.2) 120 W / 25 WRecommended min. contact load 10 mA / 10 V


InsulationTest voltage open - contact 1 kVrms 1 minuteTest voltage between poles 2.5 kVrms 1 minuteTest voltage measuring input - contacts 4 kVrms 1 minuteTest voltage measuring input - power supply 4 kVrms 1 minute



Standard types

AC/DC 12-48 V, 1560 Hz MRU32R/UC12-48VAC/DC 110-240 V, 1560 Hz MRU32R/UC110-240V

A1 A2

15 16 18 25 26 28

U2+ U3+

U U U1+

LOAD

LOAD

LOAD

AL1 AL2

N L1 L2 L3

0.10 50 100 150 200 250 300

0.2

0.3

0.5

1

2

56

10

Cur

rent

[A]

Voltage [V]

DC-1

Cyc

les


AC-1107

1050 1 2 3 4 5 6

106


1-phase monitoring

MRI11RCurrent monitoring relay AC/DC, single phase DIN Rail mounting according to DIN 43 880

Type: MRI11R/VCurrent monitoring relay with over- and under voltage thresholds up to 5 A.Alarm delay setting. Alarm LED. Display for voltmeter function, alarm signaland interactive parameter setting.1 change-over alarm contact 6 A 250 V. Comfortable parameter setting.

Monitoring function


ye rd

INPUT

al

ok

tON tOFF

AL

LIMIT 1HYST

alal

ok ok

tON tOFFtON tOFF

INPUT

AL

LIMIT 1HYST 1

HYSTLIMIT2

INPUT

al

ok

tON tOFF

AL

HYSTLIMIT1

Measuring circuit dataOver/under current setting ranges AC / DC 0 5 AFrequency DC, AC 16 100 HzResolution 100 mAAccuracy 2 % 1 digitInput resistance 5 m




InsulationTest voltage open - contact 1 kVrms 1 minuteTest voltage measuring input - contacts 4 kVrms 1 minuteTest voltage measuring input - power supply 4 kVrms 1 minute



Standard types

UC 12-48 V (AC/DC), 1560 Hz MRI11R/UC12-48VUC 110-240 V (AC/DC), 1560 Hz MRI11R/UC110-240V

A1 A2

15 16 18

I I+

LOAD

AL

N L

Connection diagram



Dimensions [mm]



0.10 50 100 150 200 250 300

0.2

0.3

0.5

1

2

56

10

Cur

rent

[A]

Voltage [V]

DC-1

Cyc

les


AC-1107

1050 1 2 3 4 5 6

106


3M

onito

ring

Rela

ys

3-phase monitoring

MRI32RCurrent monitoring relay AC/DC, three phase DIN Rail mounting according to DIN 43 880

Type: MRI32R/VCurrent monitoring relay with over- and under current thresholds up to 5 A.Alarm delay setting. Alarm LED. Display for voltmeter function, alarm signaland interactive parameter setting.2 change-over alarm contacts 6 A 250 V. Comfortable parameter setting.

Monitoring function


ye rd

INPUT

al

ok

tON tOFF

AL

LIMIT 1HYST

alal

ok ok

tON tOFFtON tOFF

INPUT

AL

LIMIT 1HYST 1

HYSTLIMIT2

INPUT

al

ok

tON tOFF

AL

HYSTLIMIT1

Measuring circuit dataOver/under current setting ranges AC / DC 0 5 AFrequency DC, AC 16 100 HzResolution 100 mAAccuracy 2 % 1 digitInput resistance 5 m




InsulationTest voltage open - contact 1 kVrms 1 minuteTest voltage between poles 2.5 kVrms 1 minuteTest voltage measuring input - contacts 4 kVrms 1 minuteTest voltage measuring input - power supply 4 kVrms 1 minute



Standard types

UC 12-48 V (AC/DC), 1560 Hz MRI32R/UC12-48VUC 110-240 V (AC/DC, 1560 Hz MRI32R/UC110-240V

A1 A2

15 16 18 25 26 28

I2 I2+ I3 I3+

I1 I1+

LOAD

LOAD

LOAD

AL1 AL2

N L1 L2 L3

Connection diagram



Dimensions [mm]



0.10 50 100 150 200 25

Documents

Comat RELECO – Railway applications