Embed Size (px)
Citation preview
COLD BREW NITRO COFFEE FULL EQUIPMENT LINE
POWERED BY
NOT YOUR AVERAGE CUP OF JOE
NITROCOFFEE
NOT YOUR AVERAGE CUP OF JOE ™
2
Introducing the new equipment line up from JoeTap®
and Micro Matic.
You can’t charge premium prices if you don’t serve a premium product – consistently.
Since nitrogen is 80 times less soluble than CO2, it’s difficult to infuse into a liquid. Other systems try to use carbonating tanks and stones to infuse nitrogen. However, this approach delivers inconsistent results, requires significant preparation and extends system recovery time between pours.
The revolutionary JoeTap® technology infuses nitrogen instantly, with no volume limitations.
Pour as many servings as you like, as fast as you possibly can, with no deviation in quality.
JoeTap® technology leaves the competition feeling flat.
QUICK COMPARISON
BARISTA CAFÉ AMERICANO
Countertop Mount X X
Floor Mount X
Nitrogen Gas Cylinder Required X X
Nitrogen Generator On-Board OPTION
NIM (Nitrogen Infusion Module) Kit On-Board X X X
Cold Brew (Still) X X X
Cold Brew Nitro X X X
Bag-N-Box (BiB) Coffee Concentrate X
Coffee, Pre-Mix (Keg Or Beverage Tank™) X X
Coffee Storage - Refrigerated X OPTION X
Filtered Water, Required X
Flash Chiller On-Board X X
JOETAP®AMERICANODIRECT DRAW / MOBILE
JOETAP® CAFÉCOUNTERTOP
JOETAP® BARISTACOUNTERTOP
COFFEE
| 3
Selected as an innovative new product
Operating Performance (Pre-production specifications, subject to change.)
Compressor 1/6 HP
BTU per hour 1135
Condenser HP 1/6
Ambient Temperature Range
45 – 100° F
Inlet Water Temperature
45 – 90° F
Ice Bath Capacity 2 gal
Approval Pending NSF and ETL approval
Running Amps5.0 A (0.5 A for Nitrogen Generator / 4.5 A for JoeTap® Countertop System)
Voltage 115/60/1
Plug Type NEMA-5-15P
Cord Length 8'
Refrigerant R-134a
Refrigerant Charge 5.5 oz / 160g
Air Clearance Around Unit
6" (153mm)
Plumbing20 – 90 PSI (138 – 621 kPa) Machine supplied with 3/8" male barb fitting
ElectricalRequires 2-wire plus ground at 120V, single phase, 60 Hz, 15 amp min. dedicated service
WarrantyOne year parts and labor warranty. All warranty work is handled through JoeTap® certified service agents.
FRONT
SIDE
204.90[8.07]
101.60[4.00]
864.95[34.05]
547.65[21.56]
532.91[20.98]
576.73[22.71]
76.20[3.00]
204.90[8.07]
101.60[4.00]
864.95[34.05]
547.65[21.56]
532.91[20.98]
576.73[22.71]
76.20[3.00]
Dimensions (Pre-production specifications, subject to change.)
JOETAP®
BARISTA
* Brushed stainless steel finish standard. Branding wraps can be designed and applied. Ask sales person for reference.
– Countertop unit offers cold brew coffee in two formats: nitro & regular “still”
– Small footprint maximizes use of your space
– Bag-in-Box (BiB) concentrate delivers large volume between changes
– Clip and click BiB changes take seconds
– All you need is power, BiB and a filtered water source, and you’re in business
4 |
Operating Performance (Pre-production specifications, subject to change.)
Compressor 1/3 HP
BTU per hour 2329
Ambient Temperature Range
45 – 90° F
Approval Pending NSF and ETL approval
Running Amps 5.0 A
Voltage 115/60/1
Plug Type NEMA-5-15P
Cord Length 8'
Refrigerant R-134a
Refrigerant Charge TBD
Air Clearance Around Unit
6" (153mm)
ElectricalRequires 2-wire plus ground at 120V, single phase, 60 Hz, 15 amp min. dedicated service
Warranty One year parts and labor
FRONT
SIDE
434.0 [17.08]150.0 [5.9]
45 [1.8]
27.5[1.08]
140.0[5.5]
627.0 [24.7]600.0 [23.6]
461.0 [18.15]
184[7.25]
438[17.24]
100[3.9]
434.0 [17.08]150.0 [5.9]
45 [1.8]
27.5[1.08]
140.0[5.5]
627.0 [24.7]600.0 [23.6]
461.0 [18.15]
184[7.25]
438[17.24]
100[3.9]
Dimensions (Pre-production specifications, subject to change.)
JOETAP®
CAFÉ
* Brushed stainless steel finish standard. Branding wraps can be designed and applied. Ask sales person for reference.
For use with shelf stable or refrigerated product.
– Dispense from a Beverage Tank™ or keg of cold brew coffee
– Choice of still cold brew or nitro cold brew coffee
– Nitrogen gives a creamy appearance, and removes bitterness from the coffee without adding milk
– Takes ambient temperature coffee and flash chills it to be served cold
– Pour two 16 oz glasses (30-45 seconds for the cold block to recover)
– Dry Cold Block technology (no water or glycol required)
– Use a standard wall outlet
– Vents underneath the unit
| 5
Operating Performance (Pre-production specifications, subject to change.)
Compressor 1/6 HP
BTU per hour 850
Ambient Temperature Range
45 – 90° F
Approval Pending NSF and ETL approval
Running Amps 2.5
Voltage 115/60/1
Plug Type NEMA-5-15P
Cord Length 8'
Refrigerant R-134a
Refrigerant Charge 5.64
Air Clearance Around Unit
6" (153mm)
ElectricalRequires 2-wire plus ground at 120V, single phase, 60 Hz, 15 amp min. dedicated service
WarrantyOne year parts and labor and additional 4 years on the compressor
SIDE
Dimensions (Pre-production specifications, subject to change.)
FRONT
593 [23.35]
711 [27.99]
406 [16.00]
785 [30.91]
635 [25.00]
197 [7.76]
1368 [53.86]
968.37 [38.12]
311 [12.24]
102 [4.02] 33.5 [1.32]
1001 [39.41]
508 [20.00]
749 [29.49]
483 [19.02]
749 [29.49]
524.44 [20.65]
302.87 [11.92]
FRONT
593 [23.35]
711 [27.99]
406 [16.00]
785 [30.91]
635 [25.00]
197 [7.76]
1368 [53.86]
968.37 [38.12]
311 [12.24]
102 [4.02] 33.5 [1.32]
1001 [39.41]
508 [20.00]
749 [29.49]
483 [19.02]
749 [29.49]
524.44 [20.65]
302.87 [11.92]
JOETAP®
AMERICANO
* Brushed stainless steel finish standard. Branding wraps can be designed and applied. Ask sales person for reference.
– Dispense from a Beverage Tank™ or keg of cold brew coffee
– Choice of still cold brew or nitro cold brew coffee
– Nitrogen gives a creamy appearance, and removes bitterness from the coffee without adding milk
– Keg can be “Y’d” to dispense one product through two faucets
– Stores the coffee cold for higher volume accounts
– Uses a standard wall outlet
– Interior mounted GIM (gas infusion module) unit nitrogenates by the glass
– NIM unit available separately
6 |
Operating Performance (Pre-production specifications, subject to change.)
Lines 1/4" I.D. GEN-X™ barrier tubing
Max Inlet Pressure 55 lbs.
Warranty One year parts and labor
Dimensions (Pre-production specifications, subject to change.)
JOETAP®
NITROGEN INFUSION MODULE KIT
131.57[5.180]
310.50[12.224]
230.54[9.076]
128.50[5.059]
131.57[5.180] 12.70
[0.50]
FRONT
TOP
* Brushed stainless steel finish standard. Branding wraps can be designed and applied. Ask sales person for reference.
– Instantly infuse your favorite beverage with nitrogen
– No wait time in between pours
– The Infusion Kit can be added to any keg box in less than 15 minutes
– Easily adjust the amount of infused nitrogen in your beverage
– Easy to clean
– 100% consistency pour after pour
| 7
[email protected] (855-456-3827)
joetap.com
micromatic.com/joetap
01796-D0317 ©2017 Micro Matic USA, Inc. All Rights Reserved. Micro Matic reserves the right to change specifications without notice.
