Catalog PEIKKO

PEIKKO GROUP

PRODUCT CATALOGUE19.11.2013

www.peikko.com

Peikko Group Concrete Connections since 1965

PEIKKO GROUP CORPORATION

Peikko supplies a large selection of concrete connectionsand composite beams both for precast and cast-in-situsolutions in wide variety of applications. Peikko, foundedin 1965, provides innovative solutions to help customersmake their building process faster, easier and morereliable.

Our aim is to serve our customers locally with leadingsolutions in the field in terms of quality, safety, andinnovation. Local sales contact information can be foundon the last pages and on our website at www.peikko.com.

APPROVALS, PRODUCT TESTING AND QUALITYThere are more than 200 Technical Approvals, eithercountry specific or ETA Approvals on the products.Detailed product specific approval information can befound in the product information of each product.

Peikko does not rely only on calculation models, but theproducts have been tested in leading universities andlaboratories. During past five years, tests have beencarried out in e.g. Czech Republic, Finland, Germany,Italy, Sweden and the UK.

The results of our quality and environment work areinspected regularly by external audits.

TECHNICAL INFORMATIONDetailed technical information and limitations forapplication, requirements for the concrete and correctionfactors for capacities can be found in the productstechnical manual. The technical manuals are available onour website at www.peikko.com or as printed manuals onrequest.

GENERAL TERMS AND CONDITIONS OFSALEPeikko Group's general terms and conditions of sale canbe found on the last pages of this Product Catalogue.

CONTACT INFORMATIONContact information to local Peikko offices can be foundon the last pages of this Product Catalogue and on ourwebsite at www.peikko.com

Peikko Group Corporation

P.O.Box 104Voimakatu 3FI-15101 Lahti, FinlandTel. +358 3 844 511Fax. +358 3 733 [email protected]

TABLE OF CONTENTS

Bolt Connections ................................................................................................. 4Anchor Bolts ............................................................................................................................... 4Column Shoes............................................................................................................................ 12Beam Shoes .............................................................................................................................. 17Wall Shoes ................................................................................................................................ 20

Fastening Products............................................................................................. 22Fastening Plates ........................................................................................................................ 22Fastening Items......................................................................................................................... 31Corner Protectors ....................................................................................................................... 36

Lifting Systems.................................................................................................. 40Rapid Coupling .......................................................................................................................... 40Threaded Lifting Systems ............................................................................................................ 44Lifting Accessories ..................................................................................................................... 55

Ties, Loops and Fixing Sockets............................................................................. 56Loops....................................................................................................................................... 56Ties and Pins............................................................................................................................. 60Fixing Sockets ........................................................................................................................... 64

Punching Prevention Systems .............................................................................. 65Punching and Shear Reinforcement System .................................................................................... 65

Flooring Products............................................................................................... 70Floor Joints............................................................................................................................... 70Dowels and Sleeves .................................................................................................................... 72

Hidden Corbels .................................................................................................. 74Column Corbels .......................................................................................................................... 74Slab Corbels .............................................................................................................................. 78

Hangers ........................................................................................................... 80Hollow-core Slab Hangers............................................................................................................ 80

Rebar Coupling Systems ...................................................................................... 82Rebar Couplers........................................................................................................................... 82

Balcony Connections .......................................................................................... 84Cantilever Slab Connectors .......................................................................................................... 84Supported Slab Connectors .......................................................................................................... 88Balcony Parapet Connectors......................................................................................................... 90

Meshes and Rebars............................................................................................. 91

Deltabeam ........................................................................................................ 92Deltabeam with precast floors ...................................................................................................... 92Deltabeam with composite floors.................................................................................................. 93Deltabeam with cast-in-situ floors ................................................................................................ 93Deltabeam in renovation ............................................................................................................. 94Deltabeam info for Designers ....................................................................................................... 94

Steel Structures ................................................................................................. 97

3Peikko Group Product Catalogue 19.11.2013

BOLT CONNECTIONS

Bolt connections are used for connecting load-bearingprecast structures, such as columns, beams and walls toother elements and foundations. The Peikko boltconnection enables an easy, fast and accurate installation.It is possible to adjust structures at the correct level andvertical position. Connections can be planned to be carriedout without propping during installation. Connections willreach their final strength after grouting.

Bolt connection capacities are defined by the bolts used inthe connection. The Peikko Designer; Column Connectionmodule enables simple and reliable dimensioning of boltconnections. Peikko Designer is available free of charge onPeikko's website.

ANCHOR BOLTS

Short stud-headed anchor bolts (type L) are principallyused as basic bolts. Long Anchor Bolts (type P) are used insplices of precast elements. Rebar HPM Anchor Bolts aremade of steel wire and Strong PPM Anchor Bolts from highstrength steel. Bolts without surface treatment are placedwithin the concrete structure where the concrete coveringprotects the bolts against corrosion. ECO galvanized andhot dip galvanized bolts are available for applicationsrequiring corrosion protection. If required, we alsomanufacture bolts to special measurements. Aninstallation template enables accurate installation of bolts.

Peikko's range also includes high-strength bolts (FatBar) for foundations of wind turbines, lines andchimney hoods as well as for other demanding constructions.

4 Peikko Group Product Catalogue 19.11.2013

Surface Coating Options

Peikko anchor bolts are available with alternativeprotective coatings. Standard coating options for anchorbolts are described below. If other type of protectionagainst corrosion, like electro-zinc-plating or stainlesssteel is needed, please contact your local Peikko salesoffice for more information.

Standard Coating OptionsStandard Coating Options

ECO Galvanizing

Peikkos ECO Galvanizing is an economical and ecological surface coating which allows anchor bolts tobe galvanized partly or completely. The coating method is thermally sprayed zinc coating (according toEN ISO 2063) and it is suitable for all Peikko anchor bolts. Minimum coating thickness is 100 m whichcorresponds to the performance of hot-dip galvanizing. Coating fulfills environmental class C3 ofstandard EN 9223-1002.

How to order ECO Galvanized bolts? Just add -ECO after the regular bolt name: HPM24P-ECO

Read more on ECO Galvanizing

Hot-Dip GalvanizingHot-Dip Galvanizing

Hot-Dip Galvanized (acc. to EN ISO 1461) anchor bolts are dipped into galvanized material completely.Method is suitable for HPM and PPM anchor bolts. Minimum coating thickness is 55 m which fulfillsenvironmental class C3 of standard EN 9223-1002.

How to order Hot-Dip Galvanized bolts? Just add -HDG after the regular bolt name: PPM30L-HDG

Rebar HPM Anchor Bolts

HPM Rebar Anchor Bolts transfer tension, compression andshear forces to the reinforced concrete base structure e.g.foundation. There are two main anchor types:

Long Anchors which are used for splices Short Anchors with headed studs which are

used for anchoring

The Long Anchor bolts transfer the compression andtension forces through the bond of the ribs of ribbed bars.The Short Anchor bolts transfer the forces through thecombination of headed studs and bond of the ribs. Boltsare color coded with same color as matching shoe types.


Approvals

ETAETA: ETA-02/0006 (HPM L)BelarusBelarus: TC 01.1331.11FinlandFinland: BY 5 B N:o 359 M1Germany:Germany: Z-30.6-39HungaryHungary: A-744/2/2007NetherlandsNetherlands: K65974/01PolandPoland: AT-15-5060/2009RomaniaRomania: 007-01/163-2009RussiaRussia: -FI.52..12094SlovakiaSlovakia: TO-09/0150 (HPM P)SwedenSweden: 0161/97TurkeyTurkey: No. 802UkraineUkraine: UA1.058.0190082-08 / UA1.058.0190088-08

CE MarkingCE Marking

HPM-L

Materials

Surface coating options available: Hot Dip Galvanizing (Zn, EN ISO 1461) and ECO Galvanizing (Zn, ENISO 2063)

Dimensions


Resistances

Strong PPM Anchor Bolts

Strong PPM Anchor Bolts transfer tension, compressionand shear forces to the reinforced concrete base structuree.g. foundation. There are two main Anchor types:


used for anchoring

The Long Anchor Bolts transfer the compression andtension forces through the bond of the ribs of ribbed bars.The Short Anchor Bolts transfer the forces through thecombination of headed studs and bond of the ribs. Boltsare color coded with same color as matching shoe types.

Approvals

FinlandFinland: BY 5 B N:o 359 M1GermanyGermany: Z-30.6-39 (PPM P)GermanyGermany: Z-21.5-1706 (PPM L)HungaryHungary: A-744/2/2007PolandPoland: AT-15-5060/2009RomaniaRomania: 007-01/163-2009RussiaRussia: -FI.52..12094SlovakiaSlovakia: TO-09/0150TurkeyTurkey: No. 802UkraineUkraine: UA1.058.0190082-08 / UA1.058.0190088-08

Materials


Surface coating options available: Hot Dip Galvanizing (Zn, EN ISO 1461) and ECO Galvanizing (Zn, ENISO 2063)

Dimensions

Resistances

Wind Turbine Foundation FatBar System

Peikko is proud to introduce its latest innovation inanchoring technology for wind turbine towers: The FatBar!Its unique design enables it to sustain greater fatigueloads, which increases the life span of turbinefoundations.

FatBars are assembled with DIN 6319 washers class 10 andDIN 6330 B nuts class 10. Bolt threads are cold-rolled withspecial threading for fatigue loading. The bolts areproduced according EN 898-1 to class 10.9.


Approvals

ETA:ETA: 10/0246

Dimensions

FatBars are available in lengths up to 6000 mm. Diameters can be chosen between 36 and 39 mm. Forother sizes please contact us.

Resistances

Heavy Duty Bolts

Peikko Peikko Heavy Duty Bolts are assembled using EN14399-6 washers class 10 and EN 4032 nuts class 10. Peikko offers choices of PVC sleeve or grease tapeprotection for a reliable post tension solution.

Resistances


Wall Shoe Anchor Bolts

Wall Shoe Anchor Bolts transfer tension, compression andshear forces to the reinforced concrete base structure e.g.foundation. The bolts are based on standard HPM and PPManchor bolt types and they are delivered with speciallydesigned AL wall shoe washers. There are two main anchortypes:


used for anchoring

The Long Anchor bolts transfer the compression andtension forces through the bond of the ribs of ribbed bars.The Short Anchor bolts transfer the forces through the combination of headed studs and bond of theribs. Bolts are color coded with same color as matching shoe types.

Materials


Dimensions

Resistances


PPL Installation Templates

PPL installation templates are used with HPM and PPManchor bolts. Bolts are accurately positioned and fixedinto the mould with Template. Anchor Bolts are fixedthrough the holes on the template with nuts and washers.Then Template is fixed to formwork with help of speciallydesigned alignment marks. Finally bolts are adjusted andtightened on the correct level. Pouring concrete can bedone easily through the hole in the middle of theTemplate.

Dimensions

PPL Installation Templates are manufactured to given specifications. Please see product informationleaflet.

COLUMN SHOES

HPKM Column Shoes are designed to correspond with theresistance of HPM Bolts, and, correspondingly, PEC ColumnShoes correspond with the resistance of PPM Bolts. Shoesare available both with a fixed and removable recess box.

The number of column shoes to be used depends on, e.g.the dimensions of the column cross section, the strengthof the concrete and the loads on the cross section. Ingeneral, four column shoes at the bottom of the columnsuffice to achieve a moment-stiff connection. Peikko'sColumn Shoes are also approved to be used in areas prone to earthquakes.


HPKM Column Shoes

HPKM Column Shoes are fastening items which are used formoment stiff connections and splices between precastconcrete columns and for example foundations. They arealso used to resist loads during erection stage and thustemporary bracing is normally not needed.

A column is fixed to anchor bolts which are cast into thestructure below the column. Fixing is achieved with nutsand washers screwed to the anchor bolts. It is alsopossible to adjust the column at the correct level andvertical position. The joint between column base andstructure below should be grouted before loading thecolumn. After grout is hardened, the joint works asreinforced concrete structure. Shoes are color coded with same color as matching anchor bolts andrecess boxes.

Approvals

FinlandFinland: BY 5 B N:o 317 (national)FinlandFinland: BY 5 B-EC 2 N:o 14 (EC2-NA)FinlandFinland: BY 5 B-EC 2 N:o 39 (HPKM-X)GermanyGermany: S/N 120397HungaryHungary: A-744/2/2007NetherlandsNetherlands: K65974/01PolandPoland: AT-15-5061/2009RomaniaRomania: 007-01/163-2009SlovakiaSlovakia: TO-09/0150TurkeyTurkey: No. 802UkraineUkraine: UA1.058.0190082-08 / UA1.058.0190088-08

Materials


Dimensions

Resistances

The resistances are defined by the bolt used in the connection.


PEC Column Shoes

PEC column shoes are fastening items which are used formoment stiff connections and splices between precastconcrete columns and for example foundations. They arealso used to resist loads during erection stage and thustemporary bracing is normally not needed.

A column is fixed to anchor bolts which are cast into thestructure below the column. Fixing is achieved with nutsand washers screwed to the anchor bolts. It is alsopossible to adjust the column at the correct level andvertical position. The joint between column base andstructure below should be grouted before loading thecolumn. After grout is hardened, the joint works asreinforced concrete structure. Shoes are color coded with same color as matching anchor bolts andrecess boxes.

Approvals

FinlandFinland: BY 5 B-EC 2 n:o 38 (EC 2 NA)FinlandFinland: BY 5 B n:o 301 (National)FinlandFinland: BY 5 B-EC 2 N:o 39 (PEC-X)GermanyGermany: S/N 080486HungaryHungary: A-744/2/2007PolandPoland: AT-15-5061/2009RomaniaRomania: 007-01/163-2009SlovakiaSlovakia: TO-09/0150TurkeyTurkey: No. 802UkraineUkraine: UA1.058.0190082-08 / UA1.058.0190088-08

Materials


Dimensions

Resistances


Recess Boxes

Recess Boxes are Fixing Accessories which are used to formrecess in concrete column for anchor bolts. There are twomain types:

CBOX is used with Column Shoes fixed incorner of the column

MBOX is used with Column Shoes fixed inmiddle of the column

Recess Boxes are color coded with same color as matchingColumn Shoes and Anchor Bolts.

Dimensions

Product code e.g. HPKM 24 - MBOXHPKM 24 - MBOX

BEAM SHOES

RBC Beam Shoes are used in precast frames to provide amoment-stiff connection between columns and beams.Typical applications include heavy frames of industrialconstructions and sports centers.


RBC Beam Shoes

RBC Beam Shoes are fastening items for moment stiffconnections between precast concrete beams and columns.The connection system consists of the beam shoes fittedin the beam and anchor bolts fitted in the column or wall.

Fixing is achieved with nuts and washers screwed to theanchor bolts. The joint between beam end and verticalstructure should be grouted before loading the beam. Aftergrout is hardened, the joint works as reinforced concretestructure. Shoes are color coded with same color asmatching anchor bolts.

Approvals

RomaniaRomania: 007-01/163-2009SlovakiaSlovakia: TO-09/0150UkraineUkraine: UA1.058.0190082-08 / UA1.058.0190088-08

Materials


Dimensions

* The longer lenghts are to be used in poor bond condition

Resistances


WALL SHOES

PSK Wall Shoes are used in tension splices of stiffeningprecast staircases, elevator shafts or other walls structures.Special Reinforced Washers (AL) are used for bolts in wallshoe connections.

PSK Wall Shoes

PSK wall shoes are fastening items which are designed fortension splices of wall-like precast concrete elements. Wallshoes are used in e.g. building's stiffening structures likecore walls and elevator shafts. The loads are transferredfrom wall to foundations or other load bearing structureswith the help of wall shoes, anchor bolts and walls'reinforcement. Fixing is done with nuts and special ALwashers as a bolt connection. PSK wall shoes are colorcoded with same color as matching anchor bolts.

Approvals

FinlandFinland: BY 5 B N:o 273 (national)FinlandFinland: BY 5 B-EC 2 N:o 21 (EC2-NA)SlovakiaSlovakia: TO-09/0150UkraineUkraine: UA1.058.0190082-08


Materials

Dimensions

Resistances


FASTENING PRODUCTS

Fastening products are used in concrete structure welding.Welding can be used to joint precast concrete elementstogether or steel structures to concrete structures. Weldingis carried out on a steel plate or angle bar anchored on thesurface of the concrete structure. Peikko's product rangeincludes a wide selection of different standard FasteningProducts. The products are tested, approved and, in termsof load resistance, designed according to Eurocodes. Ifrequired, we also manufacture fastening products tospecial measurements.

FASTENING PLATES

Fastening plates are used in concrete structure welding.The fastening plates transfer loads to the concretestructure via stud-headed anchor bolts, which are weldedto the plates, or via rebars. SBKL Fastening Plates aredesigned to carry moderate loads. Short stud-headedanchor bolts enable fastening also to thin structures. JPLFastening Plates are designed to carry heavy loads indemanding structural fastenings. Long fastening platesenable several fixings on one fastening plate. Typicalapplications are in heavy industrial construction.Fastening plates based on Peikko's stud-headed anchor bolts are ETA-approved.

We also make KL Fastening Plates with anchoring based on straight rebars. KL type fastening plates aresuitable for use close to the edges of a concrete structure, when anchoring can be taken deep into thestructure.

Standard fastening plates come with protective painting. For applications requiring corrosion protection,we produce fastening plates of stainless (e.g. SBKLR) and acid-proof steel (e.g. SBKLH). Anchor Boltsalso come without surface treatment, in which case the concrete covering provides corrosion protection,or, if required, they can be stainless.


SBKL Fastening Plates

Fastening Plate for moderate loads specially designed forwall panels, and thin and shallow structures. Stud headedanchors, plate sizes from 50 mm x 100 mm to 300 mm x300 mm, plate thicknesses from 8 to 15 mm, productdepth from 68 mm to 165 mm. Available in variousmaterial combinations in plates and studs. Please ask forfastening plates with ETA-04/0056 specification from oursales!

Approvals

ETAETA: ETA-04/0056FinlandFinland: BY 5 B N:o 381GermanyGermany: ETA-04/0056 (de)SwedenSweden: 3403/89UkraineUkraine: UA1.058.0190082-08 / UA1.058.0190088-08

Materials


Dimensions

Resistances


JPL Fastening Plates

JPL Fastening Plates are used to transfer heavy loads fromsteel structures to concrete. This is done by welding aconnection to the fastening plate. JPL Fastening Plates areespecially suitable for heavy industrial constructions.

Approvals

ETA:ETA: ETA-04/0056Finland:Finland: BY 5 B N:o 323GermanyGermany: ETA-04/0056 (de)Sweden:Sweden: 3403/89Ukraine:Ukraine: UA1.058.0190082-08 / UA1.058.0190088-08

Materials

Painted A 40 m is standardStainless and acid proof steel also available


Dimensions

Resistances


KL Fastening Plates

KL Fastening Plates are used to transfer moderate loads toconcrete. They are especially suitable when small edgedistances are required for example in column heads or wallpanel sides. Straight rebar anchors are welded on platesurface. Capacities are comparable to SBKL FasteningPlates.

Approvals

FinlandFinland: BY 5 B N:o 381RussiaRussia: RU.05.00290SwedenSweden: 3403/89UkraineUkraine: UA1.058.0190082-08 / UA1.058.0190088-08

Materials


Dimensions

Resistances


Long Fastening Plates

Long PKL, P2KL, and P3KL Fastening Plates are designed tobe used when long fixing or several fixings are needed onone plate. The length of the plates can be flexiblydesigned up to 6 m. Long Fastening Plates are especiallysuitable for heavy industrial constructions and machinefoundations. PKL, P2KL and P3KL Fastening Plates areavailable also according to European Technical Approval.

Approvals

ETAETA: ETA-04/0056FinlandFinland: BY 5 B N:o 330SwedenSweden: 3403/89UkraineUkraine: UA1.058.0190082-08 / UA1.058.0190088-08

Materials


Dimensions

Resistances

*Resistances are per one row of anchors


FASTENING ITEMS

Standard fastening items are designed for frequentconnection details in precast structures. The connectionsare typically located close to the edge of the structure,and the forces are transferred via straight rebars deeperinto the structure.

KKT Angle Bars anchor loads in the structure corners.Typical applications are in heavy industrial construction.

KKT Angle Bars

KKT Angle Bars are designed to be used when long fixingor several fixings are needed on the concrete edges. Theyare especially suitable for heavy industrial constructions.The length of the KKT Angles can be flexibly designed upto 6 m.

Approvals

FinlandFinland: BY 5 B N:o 330SwedenSweden: 3403/89UkraineUkraine: UA1.058.0190082-08

Materials


Dimensions

Resistances

*Resistances are per one row of anchors.

TR Fastening Items

TR Fastenings are especially designed for precast standarddetails connecting elements together. They can be placedclose to the structural edges and even into corners.Anchoring of the item is based on rebar anchors. Definedcapacities and tested solutions make the selection ofstandard detail safe and easy.

Approvals

FinlandFinland: BY 5 B-EC 2 n:o 31 (EC 2 NA)FinlandFinland: BY 5 B n:o 353 (National)RussiaRussia: RU.05.00290Ukraine:Ukraine: UA1.058.0190082-08 / UA1.058.0190088-08


Dimensions


Resistances

Resistances according to EC + Finnish NA.

CORNER PROTECTORS

Corner protectors are used to protect the corners ofconcrete structures against chipping. The KS CornerProtector is designed to protect the corners of columns orwalls against impacts from, for example, forklift collisions.UKT and SKT Angle Bars are used to protect the edges ofconcrete slabs. Typical applications are in heavy industrialconstruction.

SKT Angle Bars

SKT Angle Bars are designed to be used in the inner cornerof the concrete construction. They can transfer moderateloads to the concrete. The length of the SKT Angle can beflexibly designed up to 6 m. They can be cut easily torequired length at building site. Anchoring of the SKTAngle is based on rebar anchors, which are bent on site tothe right position. Delivery preferably in larger lots.

Approvals

SwedenSweden: 3403/89UkraineUkraine: UA1.058.0190082-08

Materials


Dimensions

UKT Angle Bars

UKT Angle Bars are designed to be used in the outer cornerof the concrete construction. They can transfer moderateloads to the concrete. The length of the UKT Angle can beflexibly designed up to 6 m. They can be cut easily to therequired length at building site. Anchoring of the UKTAngle is based on rebar anchors, which are bent at site tothe right position. Delivery preferably in larger lots.

Approvals

SwedenSweden: 3403/89UkraineUkraine: UA1.058.0190082-08 / UA1.058.0190088-08

Materials


Dimensions

KS Corner Protectors

KS Corner Protectors are designed to protect the corners ofcolumns and walls. They do not transfer any constructionalloads. KS Corner Protectors are recommended to be used inindustrial construction and warehouses with forklift traffic.Use of corner protectors keeps your investment in goodshape throughout its lifetime.

Approvals

SwedenSweden: 3403/89

Materials

Standard surface coating: Hot Dip Galvanized.


Dimensions

RLRK Support

RLRK Supports are designed to be used in the outer cornerof the concrete construction to support chequered platescovering openings in various passages. They do nottransfer any constructional loads. Length of RLRK Supportis 6 m and they can be cut easily to the required length atbuilding site. Anchoring of the RLRK Support is based onrebar anchors, which are bent at site to the right position.

Materials

Painted A 40 m and Hot Dip Galvanized as standard. Available also in stainless and acid proof steel.

Dimensions


LIFTING SYSTEMS

Lifting Systems are designed for the safe lifting andtransporting of precast concrete elements. LiftingComponents comprise lifting anchors, clutches and liftingloops as well as installation accessories. Peikko's liftingsystems will be CE-marked as of 1 July 2013.

RAPID COUPLING

Rapid coupling consists of rapid coupling lifting anchorsand lifting accessories suitable for various uses.

KK Anchors

KK Lifting System is a rapid coupling lifting anchor systemwith load classes ranging from 1.3 to 32 tons. The systemconsists of anchors, lifting clutches and recess formers. Itis used for lifting beams, thick slabs and wall panels aswell as concrete tubes.


Approvals

FinlandFinland: BY 5 B-EC2 n:o 5


Materials

KK anchors are produced of a special grade steel.

Resistances

Please refer to Technical Manual.

RR Anchors

RR anchors are designed and produced under strict qualitycontrol and with high performance materials to guaranteethe highest possible safety. The RR anchors has a widerange of different load classes and length and can be usedfor almost all transport applications.

Approvals

FinlandFinland: BY 5 B n:o 375 (RR, RRr, RRK, RRKr)FinlandFinland: BY 5 B n:o 331 (RRPr)


Materials

RR anchors are produced using a special grade steel.

Resistances



WRA Wire Rope Anchors

WRA anchors are designed as a rapid coupling system forlifting a wide range of precast elements. By lifting withWRA a pull-angle up to 30 is allowed. The capacity of theanchor is according to the market standard. Special sizesand length - tailor made products - are possible toproduce. WRA anchors are best solution for very heavyelements up to 99 t per lifting point.


Materials

WRA anchors are produced under using a special grade wire rope and high quality ferrules.

Dimensions

Metrics h and w can vary due to the flexibility of the rope. All WRA Anchors are zinc coated.


PNLF Sandwich Wall Anchors

PNLF anchors are designed and produced under strictquality control and with high performance materials toguarantee the highest possible safety. The PNLF anchorshas 6 different load classes a and can be used for transportprecast sandwich wall elements.

Materials

RebarsRebars: B600KX, SFS 1259TubesTubes: 1.4301 / AISI 304, EN 10088

Dimensions


When thickness of insulation E > 200 mm, PNLF is manufactured as triangle shape.

The dimension W is thickness of the insulation layer + 80 mm.

Nomination:Nomination:example. Thickness of insulation E = 240 mm and load class 5 is sufficient:PNLF5 E240PNLF5 E240

Resistances

THREADED LIFTING SYSTEMS

Peikko's JENKA family consists of nine different typesof standard threaded anchors providing a safe solution forall liftings. Anchoring is based on a rebar fastened toconcrete. Threaded systems leave a nice surface withoutlaborious finishing. You can use JENKA Lifting Devices atup to 90 degrees lifting angle.


JENKA BSA

The very short JENKA BSA anchors are speciallly designedfor lifting very thin slabs and elements. By lifting withJENKA BSA a pull-angle up to 45 is allowed. The capacityand the thread system of the anchor is according to themarket standard. Special sizes and length - tailor madeproducts - are possible to produce


Materials

JENKA anchors are produced under using a special grade steel for the sockets and high quality screws.

Dimensions

* Fs= Allowed load force from 0 - 45(Note: A load force for a mass of 1 ton demands a force of approximately 10 kN)


JENKA CSA

JENKA CSA anchors are designed for lifting a wide range ofprecast elements. By lifting with JENKA CSA a pull-angleup to 90 is allowed. The capacity and the thread systemof the anchor is according to the market standard. Specialsizes and length - tailor made products - are possible toproduce.


Materials

JENKA anchors are produced under using a special grade steel for the sockets.

Dimensions

* Fs= Allowed load force from 0 - 45* Fq= Allowed load force at 90(Note: A load force for a mass of 1 ton demands a force of approximately 10 kN)


JENKA ESA

JENKA ESA anchors are designed for lifting a wide range ofprecast elements. By lifting with JENKA ESA a pull-angleup to 90 is allowed. The capacity and the thread systemof the anchor is according to the market standard


Dimensions



JENKA PLA

JENKA PLA anchors are designed for lifting precastelements. By lifting with JENKA PLA a pull-angle up to90 is allowed. The capacity and the thread system of theanchor is according to the market standard. Special sizesand length - tailor made products - are possible toproduce.

Approvals

FinlandFinland: BY 5 B n:o 292


JENKA PSA

JENKA PSA anchors are designed for lifting of slabs andthin precast elements. By lifting with JENKA PSA a pull-angle up to 45 is allowed. The capacity and the threadsystem of the anchor is according to the market standard.Special sizes and length - tailor made products - arepossible to produce.


Materials

JENKA anchors are produced under using a special grade steel for the sockets and plates.


Dimensions


JENKA SRA

JENKA SRA anchors are designed for lifting a wide range ofprecast elements. By lifting with JENKA SRA a pull-angleup to 90 is allowed. The capacity and the thread systemof the anchor is according to the market standard. Specialsizes and length - tailor made products - are possible toproduce.

Approvals



Materials

JENKA anchors are produced under using BSt 500 S for rebars and a special grade steel for the sockets.


Dimensions


JENKA TF

JENKA TF anchors are designed for lifting a wide range ofprecast elements. By lifting with JENKA TF a pull-angle upto 90 is allowed. The capacity and the thread system ofthe anchor is according to the market standard. Specialsizes and length - tailor made products - are possible toproduce

Approvals



Materials



Dimensions


JENKA WAL

The WAL anchors can be used instead of SRA anchors if theanchoring length is limited. Wall elements and other largeelements can be lifted by WAL anchors. By lifting withJENKA WAL a pull-angle up to 90 is allowed. The capacityand the thread system of the anchor is according to themarket standard. Special sizes and length - tailor madeproducts - are possible to produce.



Materials


Dimensions


JENKA WAS

JENKA WAS anchor is designed for lifting slabs and smallelements. By lifting with JENKA WAS pull angle up to 45is allowed. The capacity and the thread system of theanchors is according to the market standard. Special sizesand length - tailor made products - are possible toproduce.


Materials

JENKA anchors are produced using BSt 500 S for rebars and a special grade steel for the sockets.


Dimensions


JENKA Lifting Devices

JENKA lifting devices are designed for lifting precastelements. By lifting with JENKA JL lifter a pull-angle up to 90 is allowed. Standard TLL are good forangle pull up to 45. The capacity and the thread system of the lifting devices is according to themarket standard.



Dimensions

JENKA Accessories

Peikko's range of products covers wide range of standardapplications. But also non standard solutions are available - do not hesitate to ask for your specialneed!


All standard applications - e. g. nailplates, recess formers etc. - are available. For aesthetic requirementsPeikko has patented stainless plugs for perfect look of elements. Special demands can also be solved byPeikko!

LIFTING ACCESSORIES

Peikko provides a wide range of different liftingaccessories for all lifting systems. Peikko's range of products covers a wide selection of standardapplications, e.g. nailing plates, recess formers, patented stainless plugs for a finished look of elements,and many more. Also tailored solutions are available.

Please do not hesitate to contact our sales!


TIES, LOOPS AND FIXING SOCKETS

PD Ties are used for joining sandwich wall panels togetherin a simple and energy-efficient way for the full height ofthe panel. A PPA Tie is used to tie the panels together atthe window or door opening beams. Each has standardmodels for insulation of up to 380 mm. PPI and PDQConnector Pins are used for joining panels togetherthrough a rebar mesh from the edges of the panels andwindow panes.

TS is a joint reinforcement in a box of galvanized sheetwith rebar anchoring for cast-in-situ joints. A narrowvariant is also available for prefabrication. PVL ConnectionLoops are used to tie the ends of wall panels together orto a column. PVL Connection Loops transfer the shearforces created from the stiffening of the building over thejoint from panel to panel.

Fixing sockets are female M-threaded fastening items,which are used for fixing points for temporary supports aswell as permanent fixings for small loads. Peikko Fixingsockets are available in black and stainless steel.

LOOPS

The Peikko Loop solution is available both for precast andcast-in situ structures. For precast, connection loops areabsolutely the easiest way to arrange reinforcement toprecast wall panel joints. Fixing into mould is easy, as isconnecting at the site: just open the cover and bend theloop to the operating position. For cast-in-situ, go for theinstallation-ready Joint Reinforcement system.


PVL Connecting Loop

PVL Connecting Loops are single wire loops for connectingprecast wall panels to each other, or to a column. PVLLoops make wall installation easy: just open the cover andbend the loop to operating position. Patented SWC willremain in bended position easy to connect toreinforcement.

Standard wire lengths of 60 mm, 80 mm, 100 mm, 120 mmand 140 mm are available for joint depth range of 80 - 140mm. The box size is 160 x 50 x 22 mm.

Approvals

FinlandFinland: BY 5 B-EC 2 N:o 26 M1FinlandFinland: BY 5 B-EC 2 N:o 32 (PVL 140)

Materials

BoxBox: Galvanized Steel SheetWire Rope LoopWire Rope Loop: High Strength Steel EN 12385-4Pressed ferrulePressed ferrule: S355J0CoverCover: Tape

Dimensions

Resistances



TS Joint Reinforcement

The TS Joint Reinforcement family contains variouselements designed for varying use. TSA Jointreinforcement is an element where the loops are concretedto the first part of the structure (from the element). InTSK Joint Reinforcement, straight rebars are concreted tothe first casting, the loops pointing out to the secondone. TSA 42 Joint Reinforcement is designed for narrow(thin) walls.

Approvals

RussiaRussia: POCC FI.AB52.H31911

Materials

BoxBox: Galvanized sheet metalRebarsRebars: A500HW / B500B / BSt 500 S


Dimensions

Sizes TSA 10-150-85TSA 10-150-85 and TSA 12-150-115TSA 12-150-115: box depth H = 50 mm.


TIES AND PINS

Complete connection between outer and inner panel ofyour sandwich wall. Multiple Tie solutions which can befinalized with Pins where needed.

PD Diagonal Ties

Ties are connecting reinforcement which allows the joiningof sandwich wall concrete panels together. Sandwich wall'sdesign is based on logic that outer panel's self weight ishung with ties and connectors into inner panel.

PD diagonal ties are designed to join sandwich panel'sconcrete layers together from full height of the panel.

PD diagonal tie is used in sandwich panel walls. Outer/inner bars are black or stainless while diagonal isstainless. Selection covers panel insulation thicknessesfrom 100 to 390 mm. Wall heights up to 3 meters andwidths up to 6 meters, for larger surfaces contact PeikkoTechnical Support.

Approvals

FinlandFinland: BY 5 B N:o 335FinlandFinland: BY 5 B-EC2 N:o 16UkraineUkraine: UA1.058.0190082-08 / UA1.058.0190088-08

Materials

DiagonalDiagonal: Stainless steelInner and outer barInner and outer bar: Black or stainless reinforcement steel depending on configuration, see TechnicalManual in Instructions and specifications.


Dimensions

T* = Recommended Insulation Thickness

Resistances

See Technical Manual in Instructions and Specifications


PPA Opening Ties

PPA beam ties can be used in low structures e.g. door andwindow beams and also in low socle elements. Made of 5mm stainless steel wire.

PPA is used in sandwich wall panels, above the window oranother opening. It is used together with PD Ties, and canbe used independently in low socle elements. Black/stainless outer/inner bars while diagonal is stainless.Insulation thicknesses from 100 to 390 mm

Approvals

FinlandFinland: BY 5 B N:o 335FinlandFinland: BY 5 B-EC2 N:o 16UkraineUkraine: UA1.058.0190082-08 / UA1.058.0190088-08

Materials

5 mm stainless reinforcement steel


Dimensions

T* = Recommended Insulation Thickness

Resistances

Vertical characteristic resistance NRky 1,5Vertical design resistance NRdy 1,1


PPI Connector Pins

PPI and PDQ connector pins are used to connect theconcrete panels of the sandwich wall together. Theconnector pins can be used for polyurethane or EPSinsulated sandwich panels, panels where footing orfoundation carries the outer concrete panel and in edgesof the panels as an additional tie.

Connector pin requires 50 mm anchoring depth. Anchoringdepth is ensured by installing the pin through insulationup to the limiter in the pin. Covers insulation thicknessesfrom 80 mm to 360 mm. Minimum connector pin length is90 mm + insulation thickness. To prevent the warping ofthe outer concrete panel the row of first pins must belocated less than 150 mm from the edge of the panel. One pin is located and installed at every corner.

Approvals

FinlandFinland: BY 5 B n:o 336 (national)FinlandFinland: BY 5 B-EC 2 n:o 17 (EC2-NA)UkraineUkraine: UA1.058.0190082-08 / UA1.058.0190088-08

Resistances

Concrete strength C25/30:Characteristic tensile resistance NRck 7,0 kNResistance value NRcd 3,5 kN

FIXING SOCKETS

Peikko provides fixings that are designed and producedunder strict quality control and from high performancematerials, galvanized or stainless steel, to guarantee thehighest possible safety. Peikko's fixings ensure maximumsafety. Fixings are available in various sizes and variations,even with pre-installed bolts.


PUNCHING PREVENTION SYSTEMS

PSB Reinforcement is designed to prevent punching failureof cast-in-situ slabs from around columns. PunchingReinforcement is an efficient industrial reinforcementwhich replaces the traditional stirrup reinforcement. It isfast and easy to install in the reinforcement.

The punching reinforcement capacity is defined inaccordance with the Eurocode. The Peikko Designer;Punching Reinforcement module enables simple andreliable dimensioning for slab punching.

PUNCHING AND SHEAR REINFORCEMENTSYSTEM

The Peikko Punching Shear Reinforcement systems enablesimple installation of the floor slabreinforcement without spacers, as the system is installedon top or with spacers under the main reinforcement. ThePunching Shear Reinforcement is used in reinforcedconcrete floor slabs that are cast directly onto columns orwalls without outriggers. The system increases thepunching shear capacity of the floor by as much as 96 %.The system is applicable to floor thickness starting from 18cm. The PSB Reinforcement System facilitatesreinforcement work compared to traditional reinforcementstirrup assembly.

Peikkos PSB Punching Reinforcement System is ETA approved as of April 2013.

PSB Reinforcement System

PSB Rails are basically used for two different ApplicationPSB Rails are basically used for two different ApplicationCases:Cases:

1. Punching Reinforcement ("PSB"):1. Punching Reinforcement ("PSB"):The Peikko PSB punching reinforcement is a powerful andeconomical solution of the punching reinforcement issuein punctiform supported in-situ and precast flat slabs,ground slabs and footings with concentrated loadinduction.


2. Shear Force Reinforcement ("PSB-S"):2. Shear Force Reinforcement ("PSB-S"):According to DIN 1045-1:2008-08, shear force load bearing capacity must be demonstrated for eachcross section of reinforced concrete building elements. As the load bearing capacity of non-reinforcedcross sections was significantly lowered vs. old DIN 1045:1988-07, shear force reinforcement is usedmore and more often in ceiling and foundation slabs.

Dimensioning:Dimensioning:PSB punching reinforcement is dimensioned according to various approvals (ETA 13/0151, GermanZ-15-1-231, Poland AT-15-7688/2008...). Therefore we recommend our user-friendly dimensioningsoftware Peikko Designer. Download it from Peikkos Software Page. Please contact our local TechnicalSupport at any time for information or dimensioning questions.

Design variants:Design variants:

PSB typePSB typeDouble headeds studs, assembled by a flat bar as spacing bar. Applicable for top and bottominstallation. Available 2 and 3- System elements or as Complete elements (2-10 and more stud rail).

PSB-F typePSB-F typeConsists of a set of components: Double headed studs connected by preassembled plastic connectors toa flat bar as spacing bar having slotted holes in it. Applicable for element slabs and preferable as spacesaving stock solution. Available as 2- and 3- System elements.


Installation variants:Installation variants:

Cast-in-situ concrete variant for top-installation.Cast-in-situ concrete variant for top-installation. For floor systems in cast-in-situ concrete, top-installation of the PSB elements is recommended. Due to that the entire remaining slab reinforcementcan be installed prior to installation of the punching reinforcement elements. By means of using a crossconnectors the proper mounting position can be ensured.

Bottom installation variantBottom installation variant. As alternative to the installation from the top, it is also possible to installPSB punching reinforcement elements from the bottom by means of Peikko spacers available forconcrete coverings from 15-45 mm prior to installing the slab reinforcement.

Precast variant.Precast variant. The multi-component type PSB-F for the use in precast factories. The partial structureenables the easy and fast installation of the punching reinforcement in the preferred phase of theautomated production process without disturbing it. PSB-F rails are mounted by means of Peikko PSBspacers (available for concrete coverings from 15-45mm) in required height on the shuttering table indefined positions marked by the plotter. Lower bending reinforcement and the lattice girders can bepositioned freely by reinforcement robot. The reinforcement work is easy, as the studs are not yet inplace. When reinforcement process is complete the required PSB-F studs are easily clicked on the rails inpredefined positions. The slotted holes on the rails offer assembly tolerance to ensure the properinstallation of the studs.


Approvals

PSB:PSB:

ETAETA: ETA-13/0151 (English)ETAETA: ETA-13/0151 (German)Czech RepublicCzech Republic: 060-033529, 060-033530GermanyGermany: Z-15.1-231HungaryHungary: A-744/1/2007PolandPoland: AT-15-7688/2008SlovakiaSlovakia: TO-09/0114UkraineUkraine: UA1.058.0190082-08 / UA1.058.0190088-08

PSB-S:PSB-S:GermanyGermany: Z-15.1-267


Materials

Double-headed studs are made from concrete reinforcement steel B500B (according to EN 10080, DIN488) and available in diameters 10, 12, 14, 16, 20,25, 28 and 32 mm. ETA-13/0151 approves the use ofPSB elements with diameters 10, 12, 14, 16, 20 and 25 mm. Elements using studs with larger diameters(28 mm and 32 mm) can be produced as well but are not within the scope of ETA-13/0151. Theassembly bar consists of structural steel S235 or B500B. Each PSB punching reinforcement component isindividually manufactured according to the static requirements. Besides in case of PSB-F type. It isspecially developed as multi-component type for stock solution in order to ensure the best flexibility.

Resistances


CUBO Column Caps

CUBO Column Caps are available in four different standarddesign types depending on the arising punching loads and the location of the column. They arecalculated according to the static requirements.

Standard design variantsStandard design variants


1. CUBO-N1. CUBO-NNormal type for internal columns

2. CUBO-H2. CUBO-HH-type for higher punching resistance and internal columns

3. CUBO-D3. CUBO-DDouble-type for high punching resistance and internal columns

4. CUBO-E4. CUBO-EEdge-type for edge columns

Materials

S355 J2+N (Norms: SIA 262,263)


FLOORING PRODUCTS

Peikko floor joint systems offer the best practical andtechnical solution for today's high quality concrete floorslabs. The system allows fast casting of the floor, givesexcellent load capacity, and minimizes cracking.

Enjoy long lasting, trouble free floors for the whole lifetime of the building!

FLOOR JOINTS

Peikko Floor Joints speed up floor construction and helpscontrol cracking in concrete slabs. The round dowels in thefloor joints transfer loads from one slab to another. Floorjoints are recommended, for example, in industrial,warehouse and sales outlet buildings with forklift traffic.

The floor joints act as leave-in-placeformwork. They alsoenable simultaneous concreting of larger areas.

TERA Joint

The TERA Joint leave-in-place floor joints allow very fastand precise casting of high quality concrete floor slabs, afeature essential for demanding applications. The Jointsections are 3 m long and manufactured to extremelyaccurate straightness so they can define the surface levelof even the most accurate slabs. Once cast-in the jointsare designed to allow concrete shrinkage to take placewith minimal restraint virtually eliminating the main causeof early stage cracking in concrete floor slabs.

The system also includes a range of intersection pieces toaid setting-out and give the highest possible quality offinish.


Materials

EZPEZP = electro zinc plated, HDGHDG = hot dip galvanized. Standard for black steel is EN 10025 and EN 10088for stainless.

Dimensions

D*D* = Advisable Floor Slab Depth

Resistances



DOWELS AND SLEEVES

A dowel and sleeve combination is also available to beused separately in casting molds. The round shape of thedowel allows slab movements both in the direction of thejoint and at a right angle to the joint. The sleeve is easyto fix to the casting mold.

TJD and TJS

Peikko Dowels are not only a key component of the FloorJoint systems but are also available supplied in setscomplete with sleeves incorporating nails for quick andeasy attachment to traditional timber formwork. The sleevedesign and dowels' unique circular shape virtuallyeliminate the possibility of slab locking' which is a majorcause of cracking in concrete floors. Also the use of highstrength, S355 steel, ensures the dowels give class-leadingload transfer capacity and yet are extremely cost-effective.

Materials

Plate dowels: S355J2+NPlastic sleeves: ABS

Dimensions


Resistances



HIDDEN CORBELS

The PCs Corbel system provides support to steeland composite beams and to concrete beams equippedwith PC Beam Shoes and transfers their support reactionsto concrete walls and columns. A light corbel system issuitable for supporting walls and intermediate landing ofstaircases both in cast-in-situ and precast frames.

COLUMN CORBELS

Peikko PCs Hidden Corbel is composed of a columncomponent to be installed in the column and an adjustablebolted bracket. The system, offering superior on-siteadjustability, enables straight precast molds. Peikko PCsCorbels are used in precast concrete beams with PC BeamShoes. The system also suits steel beams and compositebeams with suitable end plates. This hidden column corbelsystem is a natural partner for Deltabeam.

High connection resistance can be achieved with smallcross sections.

PCs Corbels

PCs Corbels are designed for connecting different kinds ofbeams: precast concrete, steel, or composite beams, tocolumns or walls. The system enables connecting as manybeams to the columns as the cross section allows.

PCs Corbels are cast in the middle of the column or walland PC UP Corbels to the upper part of the same. Use PCLOCK for safe continuous beam installation on site.


Approvals

DenmarkDenmark: 20130219 Statement, use of PCs Corbel in DenmarkFinlandFinland: BY 5 B N:o 342 (national)FinlandFinland: BY 5 B-EC 2 N:o 25 (EC2-NA)PolandPoland: AT-15-7911/2009UkraineUkraine: UA1.058.0190082-08

Materials

Dimensions


Resistances

Please refer to Technical Manual in Instructions and specifications.

PC Beam Shoes

PC Beam Shoes are used as the counterpart for PCCorbels for easy installation of both prestressed and non-prestressed precast concrete beams to columns. There aretwo different models: Low for beam flange heights < 60mm and High for > 60 mm.

Approvals

FinlandFinland: BY 5 B N:o 334 (national)FinlandFinland: BY 5 B-EC 2 n:o 15 (EC2-NA)PolandPoland: AT-15-7911/2009UkraineUkraine: UA1.058.0190082-08

Materials


Dimensions


Resistances

Resistances according to corresponding PCs Corbel.

SLAB CORBELS

PBH Corbels, easily dimensioned with design tables, areessential steel assemblies allowing TT slabs, hutchplatesand ancillary beams to be placed on supporting beamswithout the necessity of girder flanges or notched ends.Furthermore, no additional installation or assemblysupport is needed.

PBH Corbels

The PBH assembly mainly consists of two vertical steelplates mutually connected by bearing plates and top platesto create a horizontal steel beam of open cross sectionbridging the gap between the head of a TT slab and thegirder. During istallation state, the dead loads of theprecast concrete element and the in situ topping arecarried by the PBH corbel and transfered from the TT-slabto the supporting structure. In final state, when the insitu topping is hardened, the PBH corbel and the concreteslab provide a certain share of the total capacity of theconstruction. The total capacity of the construction resultsfrom the bearing capacity of the PBH corbel in installationstate and the bearing capacity of the slab.

Approvals

GermanyGermany: S-N/110135UkraineUkraine: UA1.058.0190082-08


Materials

The construction provides a fire resistance of 90 minutes.

Dimensions

Resistances



HANGERS

The PETRA Hollow-core Slab Hanger is used to support ahollow-core slab in the slab opening. PETRA is generallysupported by two parallel slabs, and one or more slabs areinstalled onto its front plate. The joint between thehollow-core slabs and PETRA should be cast before anyload is put on the structure. The beam formed by PETRAand the grouting transfers loads from the slab that needsto be supported to supporting slabs.

HOLLOW-CORE SLAB HANGERS

PETRA Slab hanger is a steel plate structured hanger for ahollow-core slab that needs to be supported between themain support points. The hanger is used for makingopenings of any size into a hollow-core slab floor. PETRAdistributes the load of the slab into the adjacent slabs.Standard sizes are available up to slab thickness of 500mm. Up to 10 m spans are easily supported with standardPETRAs.

PETRA

PETRA and PETRA Strong slab hangers are designed tosupport hollow-core slabs up to 500 mm thick formaking openings.

Special models available for hollow-core slabs withbathroom recesses and for cases where adjacent slabs areof different height.


Approvals

FinlandFinland: BY 5 B N:o 340 M1 (RakMk)FinlandFinland: BY 5 B-EC 2 N:o 20 M1 (EC2-NA)PolandPoland: AT-15-5360/2012

Materials

Dimensions

PETRA Slab Hangers are configured upon order. Please refer to the above naming instruction or the moredetailed Technical Manual under Instructions and specifications.

Resistances

Please see Technical Manual in Instructions and specifications.


REBAR COUPLING SYSTEMS

MODIX Rebar Coupler is a pressed coupling system withthreaded connection for rebar coupling. Threaded muffsare pressed to each bar for coupling. Loads are transferredvia the muff threads from one bar to the next.

Rebar splicing can be avoided with rebar couplers and, ifneeded, all bars can be continued at the same crosssection. The connection is easy to install and does notrequire special tools. Proper connection tightness can beinspected visually.

REBAR COUPLERS

MODIX is a very safe and versatile rebar splicing system.The unique visual inspection system makes it easy toensure that all connections are closed. Using the standardSM A and SM B connections, you can connect together anyrebars from size 10 to 40 mm.


MODIX Couplers

Peikko MODIX is designed to be the most safe and flexiblerebar splicing system. The unique visual inspectionsystems makes it safe and easy to be sure all connectionsare really closed. With the standard connections SMA andSMB you can connect all rebars from size 10 to 40 mm.

Approvals

AustriaAustria: TZ-2012/002/6FinlandFinland: BY 4 B N:o 23GermanyGermany: Z-1.5-177NetherlandsNetherlands: K22892/10PolandPoland: AT-15-8087/2009

Materials

MODIX muffs are produced under using a special grade steel for the muffs.


BALCONY CONNECTIONS

Balcony connectors are used for connecting balconies tothe other structures of a building. PS Balcony SlabConnector anchors the supported balcony slab to thestructures allowing vertical movement due to heat. Thestructure can be disassembled, which enables an on-sitebolted connection. The P4X Slab Connector is used toinstall a railing firmly to a balcony. A concrete parapetwith extensive adjustment possibilities can be achieved bycombining a slab connector and a parapet connector.

Peikko NIRO, an insulated cantilever balcony connector, isa solution for cantilever concrete balconies. Peikko NIROcan be cast on site into cast-in-situ structures, or to thebalcony slab at the precasting factory and later to thefloor of the building at the site.

CANTILEVER SLAB CONNECTORS

Cantilever Slab Connectors are steel reinforcementcomponents with integrated insulation to eliminate coldbridging. These slab connectors are used for transferringloads from the balcony slab to the floor slab.


NIRO Connector

Peikko NIRO insulated Cantilever Balcony Connectors aredesigned to support cantilever balconies. It is designed forslabs from 160 mm thicknesses upwards. Standard modelhas F90 fire protection, and stock lengths are 1040 mmand 540 mm.

Separate models for in situ cast floor slabs and precastfiligran slabs and precast planks.

Approvals

FinlandFinland: BY 5 B-EC 2 N:o 88RussiaRussia: RU.17.00155

Materials


Dimensions


Resistances

Design forces according to EC.

SUPPORTED SLAB CONNECTORS

Peikko's Supported Slab Connectors are hinged stainlesssteel components. They enable vertical movement ofbalconies thus preventing cracking. Simultaneously, theytransfer horizontal loads via a hinge from balcony slabs toconcrete floors. Easy installation by a bolt connection.


PS Balcony Slab Connector

PS Balcony Slab Hinge transfers horisontal loads frombalcony to the building, while enabling verticalmovements up to 20 mm. Variable sizes to fit most wallstructures. One balcony requires normally two hinges.

Approvals

FinlandFinland: BY 5 B-EC 2 n:o 35 (EC 2 NA)FinlandFinland: BY 5 B n:o 353 (National)RussiaRussia: POCC FI.AB52.H31911UkraineUkraine: UA1.058.0190082-08

Materials

PlatesPlates: 1.4301SleeveSleeve: 1.4301Ribbed barsRibbed bars: B600KX

Dimensions


BALCONY PARAPET CONNECTORS

Peikko's parapet balcony connector is an anchoring systemfor safe fixing of the parapet wall to the balcony slab. Itcan be used with concrete, steel or glass parapets and itprovides a rust-free connection without welding.

P4X Balcony Parapet Connectors

With P4X parapet connection, the reinforced concreteparapet is fastened to reinforced concrete balcony slab.P4X is also used with glass parapets/balcony glazingaccording to glass parapet producer details. The parapetpart has screws in which the parapet is stiffened againstthe balcony slab.

Approvals

FinlandFinland: BY 5 B n:o 344


MESHES AND REBARS

Rebar meshes are used in precast wall panels and concretefloors. Stainless steel meshes and rebars are used inbalcony slabs, outer panels of sandwich panels and othercorrosion-prone structures. Peikko offers a wide range ofstainless steel rebars and rebar meshes. We alsomanufacture made-to-measure meshes to meet ourcustomers' needs.


DELTABEAM

Deltabeam is a superior slim-floor system for multi-storeybuildings of any type from low-rise to high-rise. Itscomposite action between steel and concrete allows forcreative structures with large open spaces. Deltabeam hasproven through multiple fire tests its excellent ability toresist fire without any additional protection. Its shallowdesign decreases the buildings floor-to-floor height alongwith eliminating conflicts with HVAC systems. Deltabeamhas been used in concrete and steel structures in over10,000 buildings worldwide.

DELTABEAM WITH PRECAST FLOORS

Get the best out of precast floors with compositeDeltabeam allowing for frame grid area up to 12 m x 12m and 8 m x 16 m. A light structure, Deltabeam is easyand fast to install together with other elements. Save upto 500 mm in story height and reduce the volume of thebuilding with Deltabeam for energy efficiency! Ideal foroffices, schools, hospitals, office buildings, hotels and carparks. Peikko's Deltabeams are CE marked.


DELTABEAM WITH COMPOSITE FLOORS

Together with a composite floor, Deltabeam provides anenergy efficient solution by reducing the volume of thebuilding. Required rebars and HVAC and electricity pipingare easy to pass through the web holes in the beam beforethe slabs are cast. After cast-in-situ, Deltabeam forms asmooth structure together with the various compositeslabs. Use Deltabeams with steel decking, filigran typefloors or cast-in-situ. Compared to traditionalfloor structure, Deltabeam saves up to 500 mm in storyheight! Peikko's Deltabeams are CE marked.

DELTABEAM WITH CAST-IN-SITU FLOORS

Deltabeam can also be used with on-site casting ofconcrete floors. In these cases Deltabeam should be ratherstraight than precambered. The formwork should be placedjust under the bottom flange of the beam. In cases of longspans Deltabeam can alternatively be placed under thebottom surface of concrete floor. Peikko's Deltabeams areCE marked.

Deltabeams make slim floors possible also in cast-in-situconstruction!


DELTABEAM IN RENOVATION

Use Deltabeam for building completely new floor structuresin existing buildings or for rebuilding an old structure.Thanks to its lightness, Deltabeam is the ideal solution foradding more stories to a building. It helps to minimize thetotal structural weight and enables construction-phasetransfers using only forklifts. The low-height Deltabeammakes it easy to adapt the building's story height to thelevel of the stories of the adjacent buildings. Peikko'sDeltabeams are CE marked.

DELTABEAM INFO FOR DESIGNERS

To make the designing of Deltabeams easier, we havecollected information for designers on our website atwww.peikko.com. On our website, you will find a technicalmanual, installation instructions and a connection detaillibrary for preparing drawings. In case of any problems,our Technical Assistance will be happy to help youregarding Deltabeams. Peikko's Deltabeams are CE marked.


Deltabeam product information

Deltabeam is designed to be used as a structural elementcombined with all general concrete slab types: hollow-coreslab, filigran slabs, composite steel decking, trapezoidalsteel decking slabs, and cast-in-situ concrete slabs. Itenables the usage of shallow element structures andstrengthens the frame structure inside the slab.

Deltabeam can have a fire class rating as high as R120without additional protection.

Approvals

CzechCzech: 204/C5/2006/060-025293 / 060-025292FinlandFinland: VTT-RTH-03040-07GermanyGermany: Z-26.2-49PolandPoland: AT-15-8053/2009RussiaRussia: FI.93.00522SlovakiaSlovakia: TO - 08/0021SwedenSweden: SBS D/002UKUK: BBA No 05/4204UkraineUkraine: UA1.058.0190084-08 / UA1.058.0190092-08


Materials


Dimensions

*standard size unless the customer otherwise defines (minimum 20 mm).**c/c distribution for web holes is always 300 mm.


STEEL STRUCTURES

Peikko Structural Frame is a composite construction frameconsisting of Deltabeams and composite columns. It is eminently suited as a frame for office andcommercial buildings as well as public buildings.

We can assemble the delivery to meet the customer's requirements from designing the frame toinstallation.

Peikko Frame systems provide customers with several benefits:Peikko Frame systems provide customers with several benefits:

Composite actionComposite action

A true composite construction frame enables slender and light structural solutions that provide savingsin volume and costs.

On-site savingsOn-site savings

Standardized and clear connection details allow for fast and easy frame installation, providingconsiderable savings in time.

PlanningPlanning

Through our own planning and standardized connection solutions, we are able to make the correctpreselections and create an efficient planning schedule.

Competitive priceCompetitive price

Modern production technology combined with a correctly optimized frame solution enables acompetitive price.

QualityQuality

Our products and production plants are subject to external inspectorates. A quality manual is included inour delivery. Peikko's Steel Structures are CE marked.


PEIKKO GROUP CORPORATION:GENERAL TERMS ANDCONDITIONS OF SALE 2011-2012

1. Applicability

These general terms and conditions of sale shall be applied to deliveries of Products to the Customer.Peikko shall mean Peikko Group Oy or a company belonging to the same group with Peikko Group Oy.Product(s) shall mean products sold or offered by Peikko to the Customer. Customer shall mean acompany or person that purchases Products from Peikko.

These general terms and conditions shall be applied to all sales agreements between Peikko andCustomer (Parties) regarding the Products, including all future sales agreements between the Partiesand concerning the Products, even if the Parties will not expressly agree on application of these generalterms and conditions.

These general terms and conditions shall take precedence over any other written or oral conditions andover any conditions presented by the Customer, unless otherwise agreed between the Parties in writing.

2. Delivery term

Unless expressly otherwise agreed, the Products will be delivered Ex Works Peikkos Factory (as perIncoterms 2000 or its subsequent version).

3. Prices, payment term

Unless expressly otherwise agreed by the Parties, the agreed price shall be net price exclusive of VAT,i.e., it does not contain packing-, transport-, insurance-, or other similar costs, nor VAT that will beadded to the price of the delivery.

Unless otherwise agreed, the Customer shall pay the total purchase price within 14 days from the dateof the invoice.

4. Retention of title

Title to the sold Products shall remain with Peikko until the purchase price with possible interesthas been fully paid.

5. Anticipated breach

In the event there is a justified reason to doubt the Customers liquidity, due to the facts thathave arisen after conclusion of the sales agreement, Peikko may cease performance of itsobligations, for example by preventing delivery of the Products to the Customer or by preventing


installation or other use of already delivered Products, until the purchase price has been fullypaid or the Customer has placed an acceptable security.

6. Inspection of the Products

The Customer shall duly inspect the delivered Products without delay and in any event not later thanwithin seven (7) days after the delivery. Within the same time the Customer shall familiarize itself withthe delivery lists, written Product descriptions and other written material concerning the Products aswell as with available Product information at Peikkos website www.peikko.com The Customer shall makea written complaint concerning defective Products without delay and in any case not later than withinseven (7) days upon delivery of the Products. Otherwise, the delivery is deemed to be accepted by theCustomer.

Before installing, connecting or otherwise using the Products, the Customer shall once more carry outduly inspection of the Products.

7. Liability of Peikko for delayed delivery

In the event that the delivery is in delay, the Customer shall be entitled to liquidated damages equal to0.5% of the purchase price of the delayed Products per each full week of delay, provided that themaximum amount of liquidated damages shall be 5% of the purchase price.

Peikkos liability for delayed deliveries shall be limited to the payment of liquidated damages. In noevent shall Peikko be liable for any additional damages, unless Peikko has been guilty for intentionalmisconduct or gross negligence.

8. Liability of Peikko for non-conformity of the Products

Should the delivered Product be non-conforming (and provided that the Customer has given a notice ofthe lack of conformity in compliance with Clause 6), Peikko may at its option and with its own costeither repair the non-conforming Products, replace the Products with conforming Products or reimburseto the Customer the price paid for the non-conforming Products and other provable costs of theCustomer.

Should the agreed delivery be in delay due to non-conformity of the Products, the Customer shall beentitled to liquidated damages equal to 0.5% of the purchase price of the non-conforming Products pereach full week of delay, provided that the maximum amount of liquidated damages shall be 5% of thepurchase price.

Peikkos liability for non-conforming Products shall be limited to the payment of liquidated damages. Inno event shall Peikko be liable for any additional damages, unless Peikko has been guilty for intentionalmisconduct or gross negligence.

9. Limitation of liability

Peikkos liability for delay, for non-conformity of Products for other causes of any direct, indirect or anyother damage, shall be limited to the purchase price agreed by the Parties.


In no event shall Peikko be liable for lost profit or any damage caused by loss of production, loss ofturnover, or by interruption of business.

The limitation of liability is not valid should Peikko have been guilty for intentional misconduct or grossnegligence.

10. Force majeure

A Party is not liable for damage or delay in so far as the damage or delay was due to impediment beyondhis control, and provided that (a) he could not reasonably be expected to have taken into account theimpediment at the time of the conclusion of the sales agreement, and (b) he could not reasonably haveavoided or overcome its effects.

Such an impediment can be, for example; (i) strike, lockout, boycott or other action of workmen alsowhen a Party is itself an object or party thereof; (ii) fire or discontinuance of energy production,delivery of water, electricity or heating; (iii) exceptional weather condition; (iv) partial or total damageof machinery or plant; (v) lack of components, parts, raw materials or fuel; or, (v) discontinuance ofcommon transport. Subcontractors delay shall be deemed to constitute an acceptable force majeuresituation should the subcontractors delay be due to circumstances described in this clause.

A Party shall inform the other Party of the event of force majeure as well as of the termination of theevent of force majeure, as soon as reasonably possible.

In the event that the force majeure situation continues longer than three (3) months, both Parties havea right to terminate the sales agreement with immediate effect, and without liability.

11. Applicable law

The sales agreements concerning the Products concluded between the Parties shall be governedby the laws of Finland.

12. Dispute settlement

Any dispute, controversy or claim arising out of or relating to sales agreement concerning Products, orthe breach, termination or validity thereof shall be finally settled by arbitration in accordance with theArbitration Rules of the Central Chamber of Commerce of Finland. The place of arbitration shall beHelsinki.

Notwithstanding the aforesaid, Peikko may undertake legal proceedings in the district court of Helsinki,Finland.


PEIKKO GROUP CORPORATION

Peikko Group, founded in 1965, is a family owned company specializing incomposite beams and fastening products for concrete connections. Peikkoprovides innovative solutions to help customers make their building processfaster, easier and more reliable. Precasters, builders, constructors, developers,flooring specialists, machine manufactures, power plant designers, architectsand structural designers can all enjoy and take advantage of the Peikkosolutions.

The Group has offices in 30 countries in Europe, North America, and MiddleEast. The modern production facilities are located in Canada, China, Finland,Germany, Lithuania, Russia, Slovakia, United Arab Emirates, and UnitedKingdom. Peikko Group, with headquarters in Lahti, Finland, employs more than800 persons.

Peikko Group CorporationP.O. Box 104Voimakatu 3, FI-15101 Lahti, FinlandTel. +358 3 844 511Fax. +358 3 733 0152www.peikko.com

Documents

Catalog PEIKKO