ARCHITECTURE & DESIGN - Cloud Object Storage | Store …€¦ · · 2016-05-24III. REVIEW LEGEND LEGEND: Each ... Plan Review Architecture & Design / PIP Regional Director / PIP

ARCHITECTURE & DESIGN

Date: March 30, 2016

Project Team:

PC Name William Nofar 50102 Drakes Bay Drive Novi, MI 48374 248 787-6507 [email protected]

Architect Bill Jarratt Jarratt Architecture

[email protected]

Property Information:

HIEX – FORT WAYNE-EAST

(NEW HAVEN) Type/Action: PIP/CO

New Haven, IN Location #/ Inncode: 4838/NHNIN

The hotel was built in 2000 as a modified prototype with an indoor pool and small meeting room off the breakfast area.

Submittal Description:

Submittal received 03/07/16 � Exterior drawings and rendering

Submittal received 03/08/16 � Enlarged Guestroom furniture plans

(Not Included: Public Area resubmittal)

Architecture & Design Three Ravinia Drive Suite 100 Atlanta, GA 30346-2149 www.ihg.com

ARCHITECTURE & DESIGN PROPERTY

REVIEW HIEX New Haven, IN Location#4838/ Inncode: NHNIN IMPROVEMENT

DESIGN REVIEW STATUS

CONDITIONALLY APPROVED: This design submittal is conditionally approved; however all the conditions listed throughout this design review must be incorporated into the design drawings.

• Note the FF&E items noted in the guestroom plans is only a generic item number and it is required

to indicate which vendors are being selected. Either key the plan to the exact specification selection

to include vendor selection (i.e. EXG-CPT1.1, Interface carpet tile or EXG-CPT1.2 Durkan carpet tile)

or provide a furniture legend of all Formula Blue brand-specified items with vendor selections for

IHG review – Resubmit

• Resubmit Public Area per review dated 1-11-16

• All items highlighted in yellow in the included marked up PIP as well as the review comments in the

IHG Markup Summary must be addressed in the follow up submittal. Include a written response to

previous reviews describing compliance to the required revisions.

• If an item is noted to be verified, this indicates additional information must be confirmed prior to installation. An email or written response is an acceptable method to verify required information.

• All items approved except for comments referenced below and outstanding items as noted in the attached PIP. Refer to the Review Legend.

Submit revised drawings for each specific area listed throughout this review letter, and include a written letter

describing compliance to the required revisions in the follow-up submittal. Resubmit, where noted, as soon as

possible. Note the submittal due date, February 15, 2015, has passed and the project is subject to Plan

Default.

Refer to the Property Improvement Plan dated July 30, 2014for all renovation work required. This design review document describes the design submittals required and lists the design review status of each item. Items installed without InterContinental Hotels Group (IHG) approval that are deemed substandard or inappropriate to the hotel's design are subject to replacement at the discretion of IHG.

I. GENERAL INFORMATION

Franchise License/Application Status: Any approval issued by this design review document (conditional or otherwise) applies to the design of the hotel only, and does not affect the status of your application or License Agreement (as the case may be) or any requirements under the License Agreement. Contact InterContinental Hotels Group (IHG) Franchise Licensing Department and/or your franchise sales representative for inquiries regarding the status of your application or license.

This Holiday Inn brand hotel is subject to the requirements of the current Holiday Inn Standards Manual, the Americans with Disabilities Act (ADA) and all applicable building codes and ordinances. In the event of discrepancies, the most stringent requirements shall take precedence. Any deviations from Brand Standards that have not been explicitly identified in writing as part of your design submittal are not approved. Refer to the Brand Standards at www.ihgdesignconnect.com for a more complete listing of minimum design requirements. (password = IHG2016 (password is case sensitive)

II. DESIGN REVIEW COMMENTS

The following design review is specific to the drawings included with today’s design submittal. It must be understood that today’s design review is not a comprehensive listing of all design criteria or corrections that may apply to the design of your hotel. Unapproved items deemed substandard or inappropriate to the hotel's design are subject to replacement at the discretion of InterContinental Hotels Group (IHG).

Revisions, additions or alterations of any kind made to documents previously reviewed by InterContinental Hotels Group must be submitted to IHG Design Review Department for reevaluation.

Travelers with disabilities: All ADA deficiencies must be corrected in conjunction with the other requirements outlined in this review. Note that compliance with the ADA and applicable state or local laws regarding accessibility is the responsibility of the Owner. Possible ADA/accessibility deficiencies are noted within this review. However the review does not contain an exhaustive list of all possible ADA/accessibility deficiencies. All ADA/accessibility deficiencies must be corrected within the construction documents, in conjunction with the other requirements outlined in this review.

III. REVIEW LEGEND

LEGEND: Each area throughout this section is reviewed individually and given a Design Review Status for the specific area. Any applicable Action Required items are listed below the status line. 100% of all areas must be

ARCHITECTURE & DESIGN PROPERTY

REVIEW HIEX New Haven, IN Location#4838/ Inncode: NHNIN IMPROVEMENT

approved by IHG to meet the Design Review requirements per the license agreement. The definition of each review Status type is listed below:

Thank you for the submittal. Please do not hesitate to contact me with any questions.

Helen Bissell Phone: 770/604-5192 Regional Manager, Plan Review Architecture & Design Fax: 770/604-2476 e-mail: [email protected]

cc: File/DM IHG - Regional Director, Plan Review Architecture & Design / PIP Regional Director / PIP Regional Manager / via email

H O L I D A Y I N N E X P R E S S P R O P E R T Y I M P R O V E M E N T P L A N . - P A G E 4 O F 1 3 P R O P R I E T A R Y & C O N F I D E N T I A L © 2 0 1 2 S I X C O N T I N E N T S H O T E L S , I N C . - A L L R I G H T S R E S E R V E D

H O L I D A Y I N N E X P R E S S C O / L R V - 4 . 2 P R O P R I E T A R Y & C O N F I D E N T I A L

IHG will conduct field-inspections at this hotel on or about the above Renovation Milestone dates at no charge to the owner. Should these original milestone dates not be met, thereby requiring additional inspections, IHG may charge the franchisee up to $5,000.00 for each additional inspection (in addition to any other charges that might otherwise be due).

I.) EXTERIOR AREAS

A. Signage

1. No scope required.

B. Site/Parking

1. Reseal and restripe the parking lot.

2. Repair any damaged curbing and sidewalk.

C. Landscaping

1. Trim and enhance landscaping. Remove any dead or overgrown plants.

D. Porte Cochere

1. Provide new branded Porte Cochere: canopy and support columns; integrate lighting for Branded Hallmark down lighting on forward column, on front side. Include wiring for sound system for Branded Hallmark within the canopy. Provide secondary Porte Cochere canopy to bridge open space between new Porte Cochere and Hotel.

E. Building

1. Repaint the entire building. Provide branded color scheme.

2. Remove the cross pattern EIFS detailing.

VIFVIF

VIF

BisselH

APPROVED

2

BisselH

APPROVED

bisselh

APPROVED

2

bisselh

APPROVED



II.) PUBLIC AREAS

A. Lobby

1. Demolish walls between Lobby and Great Room to provide one, continuous dynamic space. √PR

2. Provide new branded floor finishes. √PR

3. Provide new branded wall finishes throughout. Introduce accent wall finishes, applied veneers, graphics for visual interest. √PR

4. Scrape, smooth, and repaint the popcorn ceiling to provide a like new appearance and comply with brand standards.

5. Construct new branded interior-scaping of Lobby space to denote various areas of activity.

Install multi-plane ceiling design consisting of headers, suspended floating ceiling panels in accent materials. √PR

Install combination of full height wing walls and half-walls, full-height column colonnade with raised decorative panels. √PR

Integrate recessed lighting system within the headers and drop ceiling panels. √PR

6. Demolish built-in front desk; construct 2 new branded free-standing check-in pods. √PR

7. Provide new Global Back Wall Panel behind front desk. √PR

8. Provide new branded furnishings and décor package. √PR

9. Remove all existing directional and informational signage throughout the entire building and replace with new, in order to comply with current Brand Standards (and logos).

B. Market

1. Provide Sundry Shop within sight of lobby- adjacent preferred; POS to be Front Desk.

2. Provide new floor, wall finishes consistent with the Lobby. √PR

3. Install new recessed lighting.

4. Provide architecturally designed and detailed millwork display shelving for inventory display. √PR

5. Provide one full size commercial grade refrigerator and one half size commercial grade freezer with glass doors. √PR

6. Install inventory per Holiday Inn Express Brand Standards. √PR

7. Hotel Sundry Shops must be compliant with the applicable Holiday Inn Express Brand Standards to sell wine and beer.

C. Business Center

1. Incorporate a free-standing computer table and chairs to accommodate minimum 2 computer stations. Provide 1 printer or wireless printing services may be available through the front desk. (More computer stations or ipad docking station allowed based on market needs.) √PR

2. Continue use of lobby tile and carpet floor finishes. √PR 3. Continue use of lobby wall colors and graphics. √PR 4. Ensure HSIA and HDTV provided throughout the public areas and guestrooms.

D. Great Room

1. Continue use of Lobby flooring into the Great Room. √PR

2. Continue use of Lobby wall colors, graphics into the Great Room. √PR

3. Continue construction of the new branded interior-scaping of the Great Room space.

Install multi-plane ceiling design consisting of headers, suspended floating ceiling panels in accent materials. √PR

Install combination of full height wing walls and half-walls, full-height column colonnade with raised decorative panels. √PR

VIF

VIF

VERIFY

VERIFY

VERIFYVERIFY

Submit millwork drawings

VIF

VIF


VIF

VERIFY

BisselH

APPROVED

1

BisselH

APPROVED

1

BisselH

APPROVED

1

BisselH

APPROVED

1



Integrate recessed lighting system within the headers and drop ceiling panels. √PR

4. Incorporate an enclosed Breakfast Buffet Area; provide the branded doors that close off the space. √PR

5. Provide branded breakfast buffet – minimum size: 30”D x 34”H x 22’L. Install Express Start breakfast components. √PR

6. Provide branded 24/7 Coffee Station- minimum size 30”D x 34”H x 5’L. √PR

7. Provide branded furnishings package: counter-height community table with integrated power/data (one required, two preferred if space allows), banquette seating and 2-top and 4-top tables and dining chairs. √PR

8. Provide new, branded décor package. √PR

E. Public Restrooms

Currently there is a single unisex restroom. Provide a second restroom so that there is a dedicated Men’s and Women’s Restroom per brand standards.

1. Replace floor and wall tile. √PR

2. Replace wall vinyl. √PR

3. Replace vanity, sink, and hardware. √PR

4. Remove the wall mounted soap dispenser. Provide in-counter soap dispenser.

5. Replace vanity mirror. √PR

6. Replace vanity light fixture. √PR

F. Meeting Area

As discussed on site, the Meeting Room may become the new Fitness Center. If the Meeting Room is to stay then the following items would be required.

1. Provide oversized cased opening entry with Barn doors from the Great Room into the space as this space is an extension of the Great Room. √PR

2. Provide branded carpet tile flooring and wood base. √PR

3. Provide branded slatted ceiling element suspended in the center of the space; integrate recessed lighting within. √PR

4. Install branded furnishings- stackable seating with tables that can be reconfigured for multiple purposes. √PR

5. Provide new branded décor. √PR

VERIFYSubmit door design/specification

Submit millwork drawingsVERIFY

VIF



III.) RECREATIONAL AREAS

A. Fitness Center

The existing fitness center is only about 200 sq. ft. and brand standards require 500 sq. ft. It is recommended to relocate the fitness center to the meeting room, or combine the fitness center with the guest room next to it.

1. Provide new branded carpet tile. √PR

2. Provide new branded wallcovering. Provide new mirror wall or oversized leaning mirrors along one wall. √PR

3. Provide congruent set of new generation fitness equipment. Number of equipment pieces per standards. √PR

4. Provide additional fitness equipment/amenities to meet market demands such as free weights, yoga ball, floor mats, etc. √PR

5. Provide wooden cornice with roller shades or wood-like blinds. √PR

6. Provide new branded matching millwork hamper and towel storage. √PR

B. Pool Area

1. Refinish and repaint the ceiling, walls, and pool deck. √PR

2. Provide new branded pool furniture. √PR



IV.) HEART OF HOUSE AREAS

A. Front Office/Admin Areas

1. Incorporate the Heart of House program.

B. Housekeeping/Laundry

1. Add a hardwired smoke detector, fire alarm with strobe, and emergency light to the Housekeeping/Laundry area to comply with IHG brand safety standards.

C. Pantry

1. Add a hardwired smoke detector and fire alarm with strobe to the Pantry to comply with IHG brand safety standards.

D. Employee Breakroom


E. Employee Restroom


VIF

VIF

VIF



V.) GUEST ROOM AREAS

A. Elevators

1. Replace flooring. √PR

2. Paint the green door a more neutral color. √PR

B. Corridors


2. Provide new branded wall finishes. √PR

3. Provide new branded decorative lighting package. √PR

4. Provide new branded drapery treatments. √PR

5. Provide new branded interior signage package.

C. Vending

Soda/food machines are no longer required on guest floors because of the first floor market; ice machines are required on every other floor.

1. Replace floor tile. √PR


3. Replace surface mounted lighting. √PR

D. Guest Laundry

1. Replace floor tile. √PR


3. Replace surface mounted lighting. √PR

E. Stairwells

1. Replace carpet.

F. Guest Rooms


Install engineered wood plank flooring or floor tile at the vestibule. (If installing tile, use same tile in the vestibule as in the bathroom.)

Install branded carpet tile, vinyl base in the sleeping room.

2. Provide new branded wall finishes; include accent wall color at window wall and entry vestibule wall. √PR

3. Provide new interior-scaping elements in the guestroom. √PR

Modify closet area (removing all closet components) and install branded Refreshment Zone in existing closet area. This includes: built in counter and shelving, coffee maker, refrigerator and microwave. (Sinks are optional, not required.)

Provide wall-mounted corner ledge in the entry vestibule.

Provide new branded acoustical barn door installed on the bath wall (facing the exterior wall) that separates the vestibule from the sleeping portion of the room. Track to be wall mounted and then encased in a finished drywall header and painted; door to be adequately sized to cover vestibule opening. Construct new wing wall to receive door when in closed position.

Provide new branded television column; construct drywall 2’6” wide column that spans from floor to ceiling.

Provide new branded laminate window frame element around the exterior window.

4. Provide new branded casegoods package. This includes headboards, nightstands, functional rack (wardrobe, luggage bench, desk, and drawers) and rolling accent tables. √PR

To be completed by September 15, 2018

VIF

VERIFY all furniture and finish selections - Refer to review for detailed comments

RESUBMIT

Submit millwork drawingsSubmit millwork drawings

Acoustical door is optional

bisselh

APPROVED

3

bisselh

APPROVED

bisselh

APPROVED

bisselh

APPROVED

2

bisselh

APPROVED

bisselh

APPROVED

1

bisselh

APPROVED

1

bisselh

APPROVED

1

H O L I D A Y I N N E X P R E S S P R O P E R T Y I M P R O V E M E N T P L A N . - P A G E 1 0 O F 1 3 P R O P R I E T A R Y & C O N F I D E N T I A L © 2 0 1 2 S I X C O N T I N E N T S H O T E L S , I N C . - A L L R I G H T S R E S E R V E D


5. Provide new branded soft seating package. This includes chaises, sleeper sofas, ottomans, desk chairs. √PR

6. Provide new branded lighting package. This includes entry lights, nightstand lights, desk lights, pendant lights. √PR

7. Provide new branded full-length mirror in the vestibule. √PR

8. Provide new branded window treatment. This includes a built-in blackout shade that operated within a fitted track mounted on the side and bottom of the window frame element. √PR

9. Provide new branded Bedding package.

10. Provide new PTACs. It is recommended to install digital thermostatic controls. √PR

11. Provide new Bedsets. √PR

12. Install a safe in the wardrobe unit. √PR

13. Install a flat panel television on television column; television wall mount must tilt and pivot. (Current requirement is 32” until replacement: 40” minimum; 42” preferred.) √PR

G. Guest Suites

1. Replace all finishes, furnishes, décor with new branded package. √PR

2. Provide an additional television in living area. √PR

3. Provide branded decorative divider panels between sleeping area and living area. √PR

4. Replace all cabinets and countertops at the wet bar locations. √PR

H. Guest Bathrooms


2. Provide new branded wall finishes. √PR

3. Repaint ceilings to provide a like new appearance.

4. Provide new branded hardwired lighting package. √PR

5. Install new branded backlit mirror; (thus eliminating vanity light fixture). √PR

6. Remove existing one-piece tub/surround units.

Tub rooms: Install new branded decorative acrylic panel tub surround system and steel or cast iron tubs. √PR

Shower rooms (permitted in King Rooms only): Install new branded decorative acrylic panel shower surround system. Install 36” shower pan and glass shower doors. √PR

7. Replace GFCI outlet with a GFCI outlet with a guide light. √PR

VERIFY - ADA rooms are to have motorized treatmentsVIF

VIFVERIFY

VIF

VIF

RESUBMIT


VIF

VERIFY

bisselh

APPROVED

3

bisselh

APPROVED

bisselh

APPROVED

bisselh

APPROVED

1

bisselh

APPROVED

1

bisselh

APPROVED

2

bisselh

APPROVED

bisselh

2

bisselh

APPROVED

3-30-16 IHG Markup Summary

Layer: B: ADASubmit enlarged plan of ADA Suite room type forIHG review

B: ADA

Layer: B: ADAMotorized window treatments are required in ADAguestrooms - Resubmit

Layer: B: ADARefer to specification EXG-405 for ADA vanitymirrors

Layer: B: ADAProvide larger smart shelves (two) in ADA roomtypes as this is where the microwave or coffeemaker is to be housed - Include millwork drawingsin resubmittal

Layer: D: Exterior ElevationsNote the columns as shown appear very heavy.Revise the overall height of stone to be morein-line with the Formula Blue design and revealingthe structural column above. Refer to prototypeimage provided to the left

D: Exterior Elevations

Layer: M: Guest RoomsThis lounge chair may be omitted as the sleepersofa is being provided and chair location appearstight

M: Guest Rooms

Layer: M: Guest RoomsA small side table is required at lounge seating -Resubmit

Layer: M: Guest RoomsInclude elevations with follow up submittal

Layer: M: Guest RoomsSubmit millwork drawings of smart shelf andrefreshment station in follow up submittal

Submit enlarged plan of ADASuite room type for IHG review

EXG-302

EXG-601

ACCENT WALL EXG-WC3.2-N

EXG-300

EXG-402

EXG-402

Motorized window treatments are requiredin ADA guestrooms - Resubmit

FLOOR:

WALL:

BASE:

EXG-T1

EXG-WC2

EXG-B3

NEWHEADER

CONVERT EXISTINGCLOSETTO REFRESMENTZONEProvide built-incounter and shelving,coffee maker,refrigerator andmicrowave. EXG-

403

Refer to specification EXG-405for ADA vanity mirrors

1

1

EXG-201

EXG-800

EXG-211

GUESTROOMACC. QQ

NEWHEADER

CONVERT EXISTINGCLOSETTO REFRESMENTZONEProvide built-incounter and shelving,coffee maker,refrigerator andmicrowave.

EXG-404

3

10

EXG-201

EXG-403

EXG-502

EXG-207

EXG-401

Provide larger smart shelves(two) in ADA room types as thisis where the microwave orcoffee maker is to be housed -Include millwork drawings inresubmittal

SHEET TITLE

A2

108 North LafayetteSouth Lyon, MI 48178248-446-1100

HOLIDAY INN EXPRESSNEW HAVENPORTE COCHERERENOVATION

3-1-16

PORTE COCHERE ELEVATIONS

PERMIT DRAWINGS

EIFIS ON2 x ADDEDFRAMING

PAINTED GALV.METAL FLASHING

1A3

NEW CULTURED STONEADDED TO EXISTINGCOLUMNS

NEW 6" x 6" PAINTED GALV.STL. GUTTER & DOWNSPOUT

LINE OF EXISTINGROOF STRUCTURE TO BE REMOVEDEXISTING STEEL BEAMS, COLUMNS,FASCIA, AND COLUMN ENLOSURESTO REMAIN TYPICALSLOPE 1/2"/FT.

NEW EFISFACSIA

M1

RR

B1B1

LS


PAINTED GALV.ON WOOD FRAMING

2A3 EXISTING FACE OF HOTEL

NEW EFISFACSIA


LINE OF EXISTINGROOF STRUCTURE TO BE REMOVEDEXISTING STEEL BEAMS, COLUMNS,FASCIA, AND COLUMN ENLOSURESTO REMAIN TYPICAL

M1

RR

B1

B1

B1

LS M1

NEW CULTURED STONE

LS

SCALE: 1/8" = 1'-0"2 SIDE ELEVATION

SCALE: 1/8" = 1'-0"1 FRONT ELEVATION

CONDITIONALLY APPROVED: This design submittal isconditionally approved; however all the conditions listed throughoutthis design review must be incorporated prior to fabrication andinstallation. Refer to each section throughout this review fordetailed design review comments for each specific area.

Note the columns as shown appear very heavy.Revise the overall height of stone to be more in-linewith the Formula Blue design and revealing thestructural column above. Refer to prototype imageprovided to the left

EXG-206

EXG-501

EXG-307

EXG-

EXG-601


EXG-300

EXG-401

This lounge chair may be omitted asthe sleeper sofa is being providedand chair location appears tight


EXG-300

EXG-402

EXG-402

A small side table is requiredat lounge seating - Resubmit

WALL:

BASE:

EXG-WC1

EXG-B4

A420 10

9

8

Include elevations withfollow up submittal

FLOOR

WALL:

BASE:

FLOOR

WALL:

BASE:

ACCENT WALWC4.1

NEW WALL

2

8

NEW SHELF

EXG-307

EXG-304EXG-210

EXG-213

PT1

C1

1

EXG-201

EXG-800

EXG-211

GUESTROOMSPA KING

1

FLOOR: EXG-T1

NEWHEADER


EXG-404

3

10

EXG-403

EXISTINGSPA

REMOVE SPAAND CAP PLUMBINGLINES AS NEEDED

EXG-401

Submit millwork drawingsof smart shelf andrefreshment station infollow up submittal

Layer: M: Guest RoomsNote: Ottomans at the nightstands are optional andmay be omitted in standard guestrooms

Layer: M: Guest RoomsAcoustical barn door is optional. If door is notbeing provided guestroom artwork is required.Include in follow up submittal

Layer: M: Guest RoomsFF&E items are keyed to the brand-specifiedFormula Blue design; however the furniture keyprovided does not indicate which vendor is beingspecified. Either key the furniture plans to theexact selected specification (i.e. EXG-CPT1.1,Interface carpet tile or EXG-CPT1.2 Durkan carpettile) or provide a furniture legend of all FormulaBlue brand-specified items with vendor selectionsfor IHG review - SubmitRefer to the furniture legend example shownbelow; however the description section is notneeded.

Layer: M: Guest RoomsThis side table may be omitted as the coffee tableis being provide

Layer: M: Guest RoomsNote: Coat hooks have been eliminated from theprototype - Omit

Layer: M: Guest RoomsAccent wallcovering, EXG-WC4.1, is to be locatedon this wall - Include revision in follow upsubmittals

Layer: M: Guest RoomsWall mount lamp is required at seating group -Resubmit

Layer: M: Guest RoomsProvide the adaptive lounge chair in Queen/Queenrooms

Layer: N: Guest SuitesThis lounge chair may be omitted as the ottomansare being provided at the nightstands and the chairlocation appears too tight

N: Guest Suites

EXG-206

XG-307


EXG-401

Note: Ottomans at the nightstandsare optional and may be omitted instandard guestrooms

FLOOR:

WALL:

BASE:

EXG-CPT1

EXG-WC1

EXG-B1

FLOOR:

WALL:

BASE:

EXG-VF1

EXG-WC1

EXG-B4

ACCENT WALL EXG-WC4.1

NEW WALL

XXX

4

2 3

9

NEW SHELF

-501

EXG-307

EXG-304EXG-210

EXG-213

EXG-201

EXG-302

-

ROOMKING

NEWHEADER


EXISTINGSPA


EXG-401Acoustical barn door is optional. If door is

not being provided guestroom artwork isrequired. Include in follow up submittal

EXG-20

EXG-501

EXG-307

EXG-307

EXG-210

EXG-213

FLOOR:

WALL:

BASE:

EXG-CPT1

EXG-WC1

EXG-B1

EXG-201

EXG-302

EXG-601

GUESTROOMSPA KING

FLOOR: EXG-VF1


NEW WALLNEWHEADER

XXX

4

2 3

NEW SHELF

EXISTSPA

EXG-300

FF&E items are keyed to the brand-specified Formula Blue design;however the furniture key provided does not indicate which vendoris being specified. Either key the furniture plans to the exactselected specification (i.e. EXG-CPT1.1, Interface carpet tile orEXG-CPT1.2 Durkan carpet tile) or provide a furniture legend of allFormula Blue brand-specified items with vendor selections for IHGreview - SubmitRefer to the furniture legend example shown below; however thedescription section is not needed.

FLOOR:

WALL:

BASE:

EXG-CPT1

EXG-WC1

EXG-B1

NEW WALL

XXX

4

2

NEW SHELF

EXG-206

EXG-307

EXG-307

EXG-304EXG-210

EXG-213

EWEADER

EXISTINGSPA


EXG-401

EXG-401

This side table may be omitted as thecoffee table is being provide

A420 10

9

8

Note: Coat hooks havebeen eliminated fromthe prototype - Omit

EXG-201

EXG-800

EXG-211

FLOOR:

WALL:

BASE:

EXG-VF1

EXG-WC1

EXG-B4

FLOOR:

WALL:

BASE:

EXG-T1

EXG-WC2

EXG-B3


NEW WALLNEWHEADER

EXG-404

A420 10

9

8

NEW SHELF

EXG-403

ACC. QQ

Accent wallcovering, EXG-WC4.1, isto be located on this wall - Includerevision in follow up submittals

FLOOR:

WALL:

BASE:

E

E

E

FLOOR:

WALL:

EX

EX

EX

ACCENT WALL EXWC4.1

NEW WALL

XX

4

2

NEW SHELF

EXG-304

CONVERT EXISTINGCLOSETTO REFRESMENTZONEProvide built-incounter and shelving,

NGREMOVE SPAAND CAP PLUMBINGLINES AS NEEDED

EXG-401

Wall mount lamp is required atseating group - Resubmit


EXG-402

Provide the adaptivelounge chair inQueen/Queen rooms

EXG-304EXG-210

EXG-213

EXG-302

EXG-601


EXG-

300

NOTE: ALL LABELED ITEMSARE REPLACING EXISTING

0 2' 4' 8'SCALE: 1/4" = 1'-0"SPA KING

This lounge chair may be omitted asthe ottomans are being provided atthe nightstands and the chairlocation appears too tight

Layer: N: Guest SuitesAccent carpet is required within suite room types atthe sofa seating group if using the carpet tileoption. Include revision with follow up submittal

Layer: N: Guest SuitesProvide visual divider wall between sofa and bedto qualify as a Suite - Resubmit

Layer: N: Guest SuitesProvide overhead cabinetry at refreshment stationto qualify as a Suite - Include millwork drawings infollow up submittal

Layer: R: ElectricalBrand Hallmark Blue Building Up-Lighting: Includes 2 to 4 blue up-lights mounted on thebuilding over the Porte Cochere. Additional highvisibility facades may be fitted with an expandedpackage of up-lighting at the owner’s option. Anowner supplied J-box is required at each fixturelocation. Exposed electrical conduit is notpermitted.Provide as required - No resubmittal required

R: Electrical

Layer: R: ElectricalBrand Hallmark Blue Porte Cochere Column downlighting: Includes 2 blue down-lights mounted toeach outside column with visibility as you face thebuilding / Porte Cochere (i.e. the front elevation oras directed by your PIP or Plan Reviewconsultant). A j-box must be installed inside thecolumns. Exposed electrical conduit is notpermitted.Provide as required - No resubmittal required

EXG-206

EXG-501

EXG-307

EXG-304EXG-210

EXG-213

EXG-302

EXG-601

KINGSUITE


EXG-

300

EXG-401 F

W

B

0 2' 4' 8'SCALE: 1/4" = 1'-0"SPA KING

Accent carpet is required within suiteroom types at the sofa seating groupif using the carpet tile option. Includerevision with follow up submittal

EXG-304

EXG-401

Provide visual dividerwall between sofa andbed to qualify as aSuite - Resubmit

EXG-307

EXG-201

G-0

EXG-211

FLOOR:

WALL:

BASE:

EXG-T1

EXG-WC2

EXG-B3

NEWHEADER


EXG-404


EXG-201

EXG-403

EXG-401

Provide overhead cabinetry atrefreshment station to qualify asa Suite - Include millworkdrawings in follow up submittal

SHEET TITLE

A2



3-1-16


PERMIT DRAWINGS



1A3




NEW EFISFACSIA

M1

RR

B1B1

LS

AINTED GALV.N WOOD FRAMING


EFISSIA

ULTURED STONE TO EXISTINGNS


M1

RR

B1

B1

B1

LS M1

NEW CULTURED STONE

LS


-0"ELEVATION

ons listed throughouto fabrication andhis review forcific area.

Brand Hallmark Blue Building Up-Lighting: Includes 2 to 4 blueup-lights mounted on the building over the Porte Cochere. Additionalhigh visibility facades may be fitted with an expanded package ofup-lighting at the owner’s option. An owner supplied J-box is requiredat each fixture location. Exposed electrical conduit is not permitted.Provide as required - No resubmittal required

SHEET TITLE

A2


3-1-16


PERMIT DRAWINGS



W EFISCSIA

CULTURED STONED TO EXISTINGMNS


M1

RR

B1

B1

B1

LS M1

NEW CULTURED STONE

LS


1'-0" ELEVATION

Brand Hallmark Blue Porte Cochere Column down lighting: Includes 2blue down-lights mounted to each outside column with visibility as youface the building / Porte Cochere (i.e. the front elevation or as directed byyour PIP or Plan Review consultant). A j-box must be installed inside thecolumns. Exposed electrical conduit is not permitted.Provide as required - No resubmittal required

SHEET TITLE

A0



3-1-16

COVER/EXTERIOR IMAGES

PERMIT DRAWINGS

11. REMOVE WALLS, CEILINGS, COUNTERS, FINISHES, EQUIPMENT AND OTHERELEMENTS AS REQUIRED FOR RENOVATION WORK. PRESERVE EXISTING HVAC,PLUMBING, ELECTRICAL WHERE POSSIBLE. PROVIDE NECESSARY BARRICADES& OTHER SAFETY MEASURES TO ENSURE HEALTH AND SAFETY OF THEBUILDING'S USERS AND EMPLOYEES.PRESERVE & STORE ALL SPECIAL ARCHITECTURAL FEATURES SUCH ASARTIFACTS, SPECIAL TRIM, SPECIAL LIGHT FIXTURES, SPECIAL MOLDINGS, ETC.,COORDINATE WITH OWNER & ARCHITECT.

12. KEEP EXISTING FIRE RATING OF ALL EXISTING STRUCTURAL ELEMENTS.

1. Field verify existing conditions. Notes and drawings may pertain toboth new, existing to remain and existing to be removed.

2. Building will Stay open during construction. Provide measures necessary to project the health, saftety and well-being of users.

4. Follow local building codes requirements for all construction. Provide and install fire detection and extinguisher, emergency, fire alarm and exit lights:as required and located by local inspector. Conform to all applicable ADA requirements.

5. All work performed shall be in accordance with AIAdocument A201 and product manufacturer's standardspecifications and instructions; including design-build work.

6. Drawings are furnished for general architectural intent.The contractor and each sub-contractor shallmake his own inspections and measurements.Refer to existing building drawings, site verificationand other information for existing building systems.

7. Color of finishes to be selected by Architect and owner unless otherwise noted.

8. Main connections for Mechanical, Plumbing and Electrical systems are design-buildby others.Reuse existing where possible. Consult with licensedengineers if changes to existing systems are required.

9. Jarratt Architecture, Inc. takes no responsibility for existing buildingconditions & current building code violations in areas that are not beingrenovated and that are design-build.

10. Existing conditions will vary, during demolition notifyArchitect of varying conditions. Additional construction detailscan be provided as requested during construction.

13. The Architect shall be the sole source of interpretation of the intent andcontent of the Drawings and Specifications, and his interpretations shall befinal and binding

14. All work is to be performed and installed in compliance with the governinglocal building codes and regulations.

15. The Contractor shall be solely responsible for obtaining access to the site todetermine and verify the existing conditions, materials, systems, sizes,dimensions, quantities, layouts, locations, and potential limitations for theperformance of the work contemplated herein.

16. It will be presumed that the Contractor has fully acquainted himself with thenature of the work and the limitations of the existing space prior to submittinghis bid, and that he has full and complete knowledge of the work to be doneand has included in his bid all required labor and materials to complete thework.

17. No extras will be allowed for claims due to unforeseen or unanticipatedconditions which, in the opinion of the Architect or the Owner, could havebeen discovered by the Contractor during normal inspection of the site duringthe bidding period and prior to the commencement of the work.

18. The Contractor shall immediately notify the Architect of any discrepancy onthe Drawings or the uncovering of hidden conditions which affect the work

19. Existing construction and conditions shown on Drawings are diagrammaticonly. The Contractor is required to verify on site exact locations, sizes, extentand conditions of existing construction and conditions.

20. These drawings are not to be scaled. If the required dimensions orinformation cannot be found herein, the Architect shall br requested tointerpret the documents, and the interpretations shall be final and binding.

21. During the construction periods the Contractor is solely responsible for thecomplete coordination of the work and the required trades so that no part ofthe work shall be left in an unfinished state as a result of lack of coordination,disagreement between the parties performing the work, or any other reason.

22. Patch and repair any damage caused to existing construction or buildingareas resulting from work performed under this contract.

23. The Contractor shall clean the entire facility to the Owner’s satisfaction uponcompletion of the work contracted here under and shall remove all tools, gangboxes and equipment from the premises. Any leftover materials resulting thework shall be properly disposed of off site.

GENERAL NOTES:

CODE NOTES:

1. BUILDING HAS EXISTING ACCESIBLE ROUTE TO THE ENTRANCE.

2. Building Use Group R-1. EXISTING AND NEW CONSTRUCTION FOR BUILDING IS OF TYPE5A CONSTRUCTION . BUILDING IS FULLY FIRE-SPRINKLED.

3. ALL NEW FINISHES TO BE MEET FLAMESPREAD REQUIREMENTS OF THE OHIO BUILDINGCODE. CLASS 1 TYPICAL

4. OCCUPANT LOADS ARE UNCHANGED FROM EXISTING

5. EXIT DOORS MUST BE OPERABLE FROM INSIDE WITHOUT A KEY OR SPECIAL KNOWLEDGE,ALL DOORS MUST BE KEYLESS IN THE DIRECTION OF EXIT/EGRESS TRAVEL

6. 1/2" MAX. THRESHHOLDS TYPICAL

.

SHEET INDEXID

A0

A1

A2

A3a

A3b

A3c

A4

A5

NameCOVER/EXTERIOR IMAGES

PORTE COCHERE FRAMING PLAN


PORTE COCHERE DETAIL 1



ELEVATIONS

ELEVATION AND COLORS

HOLIDAY INN EXPRESSNEW HAVEN, IN

SHEET TITLE

A1



3-1-16

PORTE COCHERE FRAMINGPLAN

PERMIT DRAWINGS

NEW ROOF TRUSSES AT 2'-0" o.c. (TYP.)EXISTING ROOF TRUSSES TO BE REMOVED

EXISTING

TS8"x8"x 1/2"

TYPICAL OF 4

EXISTING WALLS BELOW W/NEW CULTURED STONE ADDED

NEW FASCIAFRAMING AND EIFS

2 x 6 @ 24" OUTRIGGERS

EXISTING WALLS BELOW W/NEW CULTURED STONE ADDED

PORTION OF EXISTING WALLSBELOW TO BE REMOVED

1A3

2A3

3A3

H = 24"

EX. W18 X 50

EX. W

18 X

50

SLO

PE D

N1/

2"/F

T.

NEW 6" x 6" PAINTED GALV.STL. GUTTER THS SIDE ONLY

NEW 6" x 6" PAINTED GALV.STL. DOWNSPOUT ONTOEXISTING ROOF BELOW

EXISTING LOWER ROOF

EXISTING FACE OF HOTEL

EX. W

18 X

50

EXISTING STEELBEAMS TO REMAINTYPICAL

EX. W18 X 50

SCALE: 1/8" = 1'-0"1 FRAMING PLAN

SHEET TITLE

A2



3-1-16


PERMIT DRAWINGS



1A3




NEW EFISFACSIA

M1

RR

B1B1

LS




NEW EFISFACSIA



M1

RR

B1

B1

B1

LS M1

NEW CULTURED STONE

LS


SCALE: 1/8" = 1'-0"1 FRONT ELEVATION

CONDITIONALLY APPROVED: This design submittal isconditionally approved; however all the conditions listed throughoutthis design review must be incorporated prior to fabrication andinstallation. Refer to each section throughout this review fordetailed design review comments for each specific area.

bisselh

Polygon

bisselh

Polygon

bisselh

Polygon

bisselh

Polygon

bisselh

Callout

Brand Hallmark Blue Building Up-Lighting: Includes 2 to 4 blue up-lights mounted on the building over the Porte Cochere. Additional high visibility facades may be fitted with an expanded package of up-lighting at the owner’s option. An owner supplied J-box is required at each fixture location. Exposed electrical conduit is not permitted. Provide as required - No resubmittal required

bisselh

Callout

Brand Hallmark Blue Porte Cochere Column down lighting: Includes 2 blue down-lights mounted to each outside column with visibility as you face the building / Porte Cochere (i.e. the front elevation or as directed by your PIP or Plan Review consultant). A j-box must be installed inside the columns. Exposed electrical conduit is not permitted. Provide as required - No resubmittal required

bisselh

Polygon

bisselh

Polygon

bisselh

Image

bisselh

Cloud

bisselh

Callout

Note the columns as shown appear very heavy. Revise the overall height of stone to be more in-line with the Formula Blue design and revealing the structural column above. Refer to prototype image provided to the left

SHEET TITLE

A3a



3-1-16


PERMIT DRAWINGS

EXISTING BEAM

NEW ROOF TRUSS

NEW 2x 6 ADDEDFRAMING

NEW (2) 1 3/4 X 18" LVL, TOP RIPPEDTO FOLLOW 1/2" PER FOOTROOF SLOPE (3" AT LOW END)

1/2" DIA. BOLTS @ 16" o.c.NEW 2x6 BLOCKING

2x6 BRACE CONT.AT STEEL BEAM

2'-6"

6"7"

9"

1 1/

4"

1"

2 x 6 TOPCHORD

NEW EFIS

NEW SINGLE-PLYMEMBRANE ROOFOVER RIGID ROOFINSULATION ON5/8" APA ROOF DECK

NEW EIFSFASCIA &SOFFIT

2" CONT. VENTW/ SCREEN

METAL CLG.SOFFIT


NEW 2 x 4FRAMING

NEW EIFSSOFFIT

NEWCULTUREDSTONEADDED TOEXISTINGCOLUMNS

NEW PAINTED GALV.FLASHING AND CLIPMATCH ADJ. EIFS

NEW PAINTED GALV.FLASHING AND CLIP

M1

RR

B1

LS

LS

RR

M1

M2

NEW 8d @ 6"TO BLOCKING

1/2" DIA.BOLTS@16"

SIMPSON LPT4@ 24" O.C.

SIMPSON #25EACH TRUSS

2 x 6 NAILER W/ 1/2" DIA.BOLTS @ 24"

NEW 3 1/2" x 2 1/2"x 1/4" x CONT.

NEW 5/8"GYP. BD.

SCALE: 1" = 1'-0"1 PORTE COCHERE DETAIL

SHEET TITLE

A3b



3-1-16


PERMIT DRAWINGS

EXISTINGW8 x 35BEAM

NEW ROOF TRUSS

NEW 2 x ADDEDFRAMING

1/2" DIA. BOLTS@ 16" o.c.

NEW 2x6 BLOCKINGW/ SIMPSON A35

NEW 2 x 6 @ 16"PONY WALL 1/2" PER FOOT

ROOF SLOPE

2'-6"

6"

7"9"

NEW 2 x 6 @ 24"OUTRIGGERS

NEW EFIS

NEW SINGLE-PLYMEMBRANE ROOFOVER RIGID ROOFINSULATION ON5/8" APA ROOF DECK

NEW EIFSFASCIA &SOFFIT


NEW METALCLG. SOFFIT


NEW 2 x 4FRAMING

NEW EIFSSOFFIT


NEW PAINTED GALV.FLASHING AND CLIPMATCH ADJ. EIFS


B1

RR

M1

A2

LS

RR

M1

M2


M1 NEW 5/8"EXTERIORGYP. BD.

SIMPSONH25 @ 4'-0" O.C.

NEW 7/16" APASHEATHING

8d @ 6"

NEW 2 x 6NAILERW/ 1/2" DIA.BOLTS @ 24"

SIMPSON A35HANGER

NEW 5/8" APASHEATHING

NEW 5/8"GYP. BD.


SHEET TITLE

A3c



3-1-16


PERMIT DRAWINGS

EXISTING BEAM

ROOF TRUSS

2- 2x6 PLATES

2x 6 ADDEDFRAMING

2x6 NAILER WITH1/2" DIA. BOLTS @ 16" o.c.

2- 2x4 BLOCKING

2x6 BRACE CONT.AT STEEL BEAM

6" 2'-6"

3"

6"

6"6"

SLOPED TOPCHORD OFTRUSS 1/8"/FTTO CENTERSPAN

EXISTING EFISFACSIAVERIFY

NEW 6" x 6"PAINTEDGALV. GUTTER

SINGLE-PLYMEMBRANE ROOFOVER RIGID ROOFINSULATION ONAPA ROOF DECK

NEW EIFSSOFFIT


PAINTEDEXTERIORGYP BD.SOFFIT

SLOPE DN


NEW 2 x 4 BRACE

NEW EIFSSOFFIT


ADDEDINSULATIONAND EIFS ONCOLUMN CAP


SHEET TITLE

A4



3-1-16

ELEVATIONS

PERMIT DRAWINGSS:\A

rchi

ve D

raw

ings

\Hot

els\

Hol

iday

Inn\

New

Hav

en, I

N 9

9121

\A-4

.dw

g, 9

/18/

2015

11:

50:5

5 A

M, D

WFx

ePl

ot (X

PS C

ompa

tible

).pc3

RRRRRR

RRRRRRRR

RR

RR

RR RR RR

RR RR RR

DB

DBDBDBDBDBDBDBDB

DB DB

DBDB DB

LSS

LS

LSLSLS

LSLS

LSSLSS LSS

WH

WH

WH

WH

WHWH

WH

WHWH

FILL-IN GRIDS ANDARCHES WITHINSULATION AND EIFS

FILL-IN ARCHES WITHINSULATION AND EIFS

RRRR RR RR RR RR RR RR

LS

Approved by IHG03/30/2016

SHEET TITLE

A5



3-1-16

ELEVATION AND COLORS

PERMIT DRAWINGS

RRRRRR

RRRR

RR RR RR RRRR

RR RR RR RR

DB DB DBDB

DB DB DB DB DBDB DB

RR

LSS LSS

LS LS LSLS

LS LSLS LS

WH

WHWH

WHFILL-IN ARCHES WITHINSULATION AND EIFS

RR RR RR RR

LS

HOLIDAY INN EXPRESS® – Brand Design InterContinental Hotels Group

Exterior Design & Construction Three Ravinia Drive, Suite 100

AREA: Exterior Colors Atlanta, GA 30346

Date: 3/26/2015

Smooth (533),

Color Snowball

10400L

Snowball HIEX-06-

1085

90-68-2-3-9

Finish, Color

PX10400L

EIFS-GR (same as

EIFS-DB)

Parex Sand

Smooth (533),

Color Twig 3021L

Color: Virtual

Taupe SW7039

Demandit,

Sandpebble Twig

Fine DPR

HIEX-04-1022

90-28-1-12-3

Sto Fine Sand

Finish, Color

PX3021L

Natural Scheme:

Spec Number Parex Sherwin Williams Dryvit Sto

EIFS-LS

Parex Multi

Texture (532),

Color Moondance

3027L

Color: Accessible

Beige SW7036

Demandit,

Moondance

HIEX-03-1085

90-68-2-3-1

Sto Freeform

Finish, Color

3027L

EIFS-LSS

Parex Sand

Smooth (533),

Color Moondance

3027L

Color: Accessible

Beige SW7036

Demandit,

Moondance

HIEX-03-1085

90-68-2-3-1

Sto Limestone

Finish, Color

3027L

HOLIDAY INN EXPRESS® – Brand Design InterContinental Hotels Group

Exterior Design & Construction Three Ravinia Drive, Suite 100

AREA: Exterior Colors Atlanta, GA 30346

Date: 3/26/2015

EIFS-DB

Parex Sand Fine

(534), Color

Rawhide T022L

Tatami Tan

SW6116

Demandit,

Rawhide

HIEX-07-1085

90-68-2-3-11

Sto Fine Sand

Finish, Color

T022L

EIFS-RR

Parex Sand

Smooth (533),

Color Santiago

3032L

Color: Backdrop

SW7025

Demandit,

Santiago HIEX-08-

1085

90-68-2-3-13

Sto Fine Sand

Finish, Color

PX3032L

EIFS-WH

Parex Sand

Smooth (533),

Color Snowball

10400L

Alabaster SW7008

Demandit,

Snowball HIEX-06-

1085

90-68-2-3-9

Sto Fine Sand

Finish, Color

PX10400L

EIFS-GR (same as

EIFS DB)

Parex Sand Fine

(534), Color

Rawhide T022L

Tatami Tan

SW6116

Demandit,

Rawhide

HIEX-07-1085

90-68-2-3-11

Sto Fine Sand

Finish, Color

T022L

Approved by IHG03/30/2016

DATE DESCRIPTION

3/4/2016 Conceptual

SHEET TITLE

CONSULTANTS

A-102

GUESTROOM PLANS

Holiday Inn ExpressNew Haven, Indiana


EXG-206

EXG-501

EXG-307

EXG-307

EXG-304EXG-210

EXG-213

FLOOR:

WALL:

BASE:

EXG-CPT1

EXG-WC1

EXG-B1

EXG-201

EXG-302

EXG-800

EXG-601

EXG-211

KINGSUITE

FLOOR:

WALL:

BASE:

EXG-VF1

EXG-WC1

EXG-B4

FLOOR:

WALL:

BASE:

EXG-T1

EXG-WC2

EXG-B3



NEW WALLNEWHEADER


EXG-404


XXX

4

2 3

A420 10

9

8

NEW SHELF

EXG-201

EXG-403

EXG-

300

EXG-401

EXG-401

EXG-206

EXG-501

EXG-307

EXG-307

FLOOR:

WALL:

BASE:

EXG-CPT1

EXG-WC1

EXG-B1

EXG-201

EXG-302

EXG-800

EXG-601

EXG-211

GUESTROOMKING

FLOOR:

WALL:

BASE:

EXG-VF1

EXG-WC1

EXG-B4

FLOOR:

WALL:

BASE:

EXG-T1

EXG-WC2

EXG-B3



NEW WALLNEWHEADER


EXG-404


XXX

4

2 3

A420 10

9

8

NEW SHELF

EXG-601

EXG-213

EXG-201

EXG-403


EXG-402

EXG-401

EXG-401

FLOOR:

WALL:

BASE:

EXG-CPT1

EXG-WC1

EXG-B1

EXG-201

EXG-302

EXG-800

EXG-403

EXG-502

EXG-502

EXG-601

EXG-211

GUESTROOMQQ

EXG-207

FLOOR:

WALL:

BASE:

EXG-VF1

EXG-WC1

EXG-B4

FLOOR:

WALL:

BASE:

EXG-T1

EXG-WC2

EXG-B3



NEW WALLNEWHEADER


EXG-301

EXG-213

EXG-404


A420

4

2 3

A420

10

9

8

NEW PTAC

EXG-402

EXG-401

FLOOR:

WALL:

BASE:

EXG-CPT1

EXG-WC1

EXG-B1

EXG-201

EXG-302

EXG-800

EXG-601

EXG-211

GUESTROOMACC. QQ

FLOOR:

WALL:

BASE:

EXG-VF1

EXG-WC1

EXG-B4

FLOOR:

WALL:

BASE:

EXG-T1

EXG-WC2

EXG-B3



NEW WALLNEWHEADER


EXG-404

XXX

4

2 3

A420 10

9

8

NEW SHELF

EXG-201

EXG-403

EXG-502

EXG-207

EXG-300

EXG-402

EXG-401

EXG-402

EXG-206

EXG-501

EXG-307

EXG-307

FLOOR:

WALL:

BASE:

EXG-CPT1

EXG-WC1

EXG-B1

EXG-201

EXG-302

EXG-800

EXG-601

EXG-211

GUESTROOMACC. KING

FLOOR:

WALL:

BASE:

EXG-VF1

EXG-WC1

EXG-B4

FLOOR:

WALL:

BASE:

EXG-T1

EXG-WC2

EXG-B3



NEW WALLNEWHEADER


EXG-404

XXX

4

2 3

A420 10

9

8

NEW SHELF

EXG-601

EXG-213

EXG-201

EXG-403

EXG-402

EXG-401

EXG-401

EXG-206

EXG-501

EXG-307

EXG-307

EXG-304EXG-210

EXG-213

FLOOR:

WALL:

BASE:

EXG-CPT1

EXG-WC1

EXG-B1

EXG-201

EXG-302

EXG-800

EXG-601

EXG-211

GUESTROOMSPA KING

FLOOR:

WALL:

BASE:

EXG-VF1

EXG-WC1

EXG-B4

FLOOR:

WALL:

BASE:

EXG-T1

EXG-WC2

EXG-B3



NEW WALLNEWHEADER


EXG-404


XXX

4

2 3

A420 10

9

8

NEW SHELF

EXG-403

EXISTINGSPA

EXG-300


EXG-401

EXG-401

0 2' 4' 8'SCALE: 1/4" = 1'-0"5 KING SUITE0 2' 4' 8'SCALE: 1/4" = 1'-0"1 KING

0 2' 4' 8'SCALE: 1/4" = 1'-0"2 QQ Guestroom0 2' 4' 8'SCALE: 1/4" = 1'-0"4 ACC. QQ

0 2' 4' 8'SCALE: 1/4" = 1'-0"3 ACC. KNG

0 2' 4' 8'SCALE: 1/4" = 1'-0"6 SPA KING

bisselh

Callout

This lounge chair may be omitted as the sleeper sofa is being provided and chair location appears tight

bisselh

Callout

A small side table is required at lounge seating - Resubmit

bisselh

Callout

This lounge chair may be omitted as the ottomans are being provided at the nightstands and the chair location appears too tight

bisselh

Rectangle

bisselh

Callout

Accent carpet is required within suite room types at the sofa seating group if using the carpet tile option. Include revision with follow up submittal

bisselh

Text Box

Submit enlarged plan of ADA Suite room type for IHG review

bisselh

Callout

Include elevations with follow up submittal

bisselh

Callout

Submit millwork drawings of smart shelf and refreshment station in follow up submittal

bisselh

Callout

Note: Ottomans at the nightstands are optional and may be omitted in standard guestrooms

bisselh

Callout

Acoustical barn door is optional. If door is not being provided guestroom artwork is required. Include in follow up submittal

bisselh

Text Box

FF&E items are keyed to the brand-specified Formula Blue design; however the furniture key provided does not indicate which vendor is being specified. Either key the furniture plans to the exact selected specification (i.e. EXG-CPT1.1, Interface carpet tile or EXG-CPT1.2 Durkan carpet tile) or provide a furniture legend of all Formula Blue brand-specified items with vendor selections for IHG review - Submit Refer to the furniture legend example shown below; however the description section is not needed.

bisselh

Image

bisselh

Callout

This side table may be omitted as the coffee table is being provide

bisselh

Callout

Note: Coat hooks have been eliminated from the prototype - Omit

bisselh

Callout

Motorized window treatments are required in ADA guestrooms - Resubmit

bisselh

Callout

Accent wallcovering, EXG-WC4.1, is to be located on this wall - Include revision in follow up submittals

bisselh

Line

bisselh

Arrow

bisselh

Cloud

bisselh

Callout

Wall mount lamp is required at seating group - Resubmit

bisselh

Callout

Provide visual divider wall between sofa and bed to qualify as a Suite - Resubmit

bisselh

Callout

Provide overhead cabinetry at refreshment station to qualify as a Suite - Include millwork drawings in follow up submittal

bisselh

Callout

Refer to specification EXG-405 for ADA vanity mirrors

bisselh

Callout

Provide the adaptive lounge chair in Queen/Queen rooms

bisselh

Callout

Provide larger smart shelves (two) in ADA room types as this is where the microwave or coffee maker is to be housed - Include millwork drawings in resubmittal

Documents

ARCHITECTURE & DESIGN - Cloud Object Storage | Store …€¦ · · 2016-05-24III. REVIEW LEGEND LEGEND: Each ... Plan Review Architecture & Design / PIP Regional Director / PIP