1. NIT HEADER TENDER DOCUMENT · 2020. 9. 15. · Description:- Supply of AC 110V Lit LED signal lighting Unit as per RDSO/Spn/153/2011 rev4.1 or latest RDSO specification for - Shunt

CE/Co-ordination acting for and on behalf of The President of India invites E-Tenders against Tender No KR-JK-ST-SIG-TELE-03-2020 Closing Date/Time 29/10/2020 15:00 Hrs. Bidders will be able to submit their original/revised bids upto closing date and time only.Manual offers are not allowed against this tender, and any such manual offer received shall be ignored.

Contractors are allowed to make payments against this tender towards tender document cost and earnest money only through onlypayment modes available on IREPS portal like net banking, debit card, credit card etc. Manual payments through Demand draft, Bankercheque, Deposit receipts, FDR etc. are not allowed.

1. NIT HEADER

Name of Work

"Work of Design, Manufacture, Supply, Installation, Testing & Commissioning of ElectronicInterlocking based Signalling System Compatible for CTC working between Dugga(excluding) - Basindadhar (including) and Sangaldan (including) Stations with 6 Quad andOFC based communication system between Km 66.500 to Km 101.600 (Excluding from Km73.785 to Km 91.200 of IRCON Portion) of BG single Line on Katra - Dharam Section ofUSBRL Project of Northern Railway in Jammu & Kashmir UT"

Bidding type Normal Tender

Tender Type Open Bidding System Two Packet System

Tender Closing Date Time 29/10/2020 15:00 Date Time Of Uploading Tender 15/09/2020 19:29

Pre-Bid Required Yes Pre-Bid Query Date Time 05/10/2020 10:00

Advertised Value 772063481.00 Tendering Section JAMMU

Bidding Style Single Rate for Tender Bidding Unit Above/Below/Par

Earnest Money /Bid Security(Rs.) 4010300.00 Validity of Offer ( Days) 90

Tender Doc. Cost (Rs.) 29500.00 Period of Completion 18 Months

Contract Type Works Contract Category Expenditure

Bidding Start Date 15/10/2020Are Joint Venture (JV) firmsallowed to bid Yes

Ranking Order For Bids Lowest to Highest Expenditure Type Capital (Works)

2. SCHEDULE

S.No. Item Code Item Qty Qty Unit Unit Rate Basic Value Escl.(%) Amount BiddingUnit

Schedule A-SCHEDULE-A 12677808.00

1011010 50.00 Kilometre 213105.00 10655250.00 AT Par 10655250.00

Description:- Supply of 12 Core x 1.5 Sq.mm

2011020 4.00 Kilometre 323871.00 1295484.00 AT Par 1295484.00

Description:- Supply of 12 x 2.5Sq.mm (Copper)

3011030 6.00 Kilometre 121179.00 727074.00 AT Par 727074.00

Description:- Supply of Power cable 2 x 25 Sq.mm (Al)


Schedule B-SCHEDULE-B 32806929.00

1021010 1.00 Set 97427.00 97427.00 AT Par 97427.00

Description:- Supply of Design set for circuits

2021021 230.00 Numbers 3820.00 878600.00 AT Par 878600.00

Description:- Relay Metal to Carbon - Supply of Relay -QN1 (Contact configuration 12F/4B or 8F/8B asrequirement of consignee)

3021022 120.00 Numbers 3988.00 478560.00 AT Par 478560.00

Description:- Relay Metal to Carbon - Supply of Relay -QNA1 (Contact configuration 12F/4B or 8F/8B asrequirement of consignee)

4021023 6.00 Numbers 4651.00 27906.00 AT Par 27906.00

Description:- Relay Metal to Carbon - Supply of Relay -QNA1K

5021024 140.00 Numbers 5316.00 744240.00 AT Par 744240.00

Description:- Relay Metal to Carbon - Supply of Relay -QECX (ON/OFF Aspect)

6

021031 4.00 Numbers 50619.00 202476.00 AT Par 202476.00

Page 1 of 28 Run Date/Time: 15/09/2020 19:30:05

PROJECT-J AND K-S AND T/KRCLTENDER DOCUMENT

Tender No: KR-JK-ST-SIG-TELE-03-2020 Closing Date/Time: 29/10/2020 15:00

6Description:- Panel, Rack & Fuses - Supply of Main Cable Termination Rack complete as per DRG. No.RVNL/S&T/SG-076/2012 along with patching cable of 24 core.

7021032 4.00 Per Unit 7874.00 31496.00 AT Par 31496.00

Description:- Panel, Rack & Fuses - Supply of prewired Crank handle cum key lock relay box (Per Unit=Box)

8021041 80.00 Numbers 226.00 18080.00 AT Par 18080.00

Description:- Supply of Non-deteriorating type fuse holders and fuse links - Fuse holder 20 Amps Capacity

9021042 80.00 Numbers 32.00 2560.00 AT Par 2560.00

Description:- Supply of Non-deteriorating type fuse holders and fuse links - Fuse links 16 Amps

10021043 80.00 Numbers 32.00 2560.00 AT Par 2560.00


11021044 100.00 Numbers 30.00 3000.00 AT Par 3000.00


12021045 100.00 Numbers 32.00 3200.00 AT Par 3200.00


13

021051 2.00 Set 842366.00 1684732.00 AT Par 1684732.00

Description:- Block Instrument - Supply of UFSBI (2 nos. as per RDSO/SPN/147/2005 with latest amendments),SM's (block) Panel for Single line (2 nos per station as per RDSO/S/32019), Block Telephone & Relay Rackcompletely wired fully with all relays required for Block working with Axle Counter in RE area

14

021061 2.00 Set 1182818.00 2365636.00 AT Par 2365636.00

Description:- Power Supply - Supply of Integrated Power Supply (IPS) System, SMPS based arrangement withbattery set of 300AH, Hydrometer suitable for EI/PI/RRI. RDSO Specification No.RDSO/SPN/165/2012 version 3.0or Latest.

15021072 14.00 Kilometre 88340.00 1236760.00 AT Par 1236760.00

Description:- Outdoor Signalling work - Supply of PIJF cable of size 10 PAIR x 0.63 mm

16021073 4.50 Kilometre 132344.00 595548.00 AT Par 595548.00

Description:- Supply of PIJF cable of size 20 PAIR x 0.63 mm

17021074 2.00 Kilometre 249065.00 498130.00 AT Par 498130.00

Description:- Supply of PIJF cable of size 50 PAIR x 0.63 mm

18021075 14.00 Kilometre 84978.00 1189692.00 AT Par 1189692.00

Description:- Supply of 24 fibre armoured optic fibre cable

19021081 3000.00 Metre 165.00 495000.00 AT Par 495000.00

Description:- Trenching, Laying & protection work - Supply of RCC pipes of size 150mm dia, 2 mtr long alongwith collars

20021082 2200.00 Metre 265.00 583000.00 AT Par 583000.00

Description:- Supply of DWC pipe size 120mm outer dia & 102 mm inner dia.

21021083 1900.00 Metre 1144.00 2173600.00 AT Par 2173600.00

Description:- Trenching, Laying & protection work - Supply of Galvanised Iron pipe 100mm dia B class IS 1239(Part-I) with end clamps

22021084 99.00 Numbers 5675.00 561825.00 AT Par 561825.00

Description:- Trenching, Laying & protection work - Supply & Jointing of Quad Cable with thermo shrinkableJointing Kits as per IRS:TC 77/2012 Revision-3

23021091 22.00 Numbers 40955.00 901010.00 AT Par 901010.00

Description:- COLOUR LIGHT SIGNALS - Supply of 2 aspect Colour light signal complete with Signal post, CIbase, ladder, platform, front staging, CLS unit 2 aspect, Anchor bolt, nut washer, Universal lock with key etc

24021092 10.00 Numbers 48584.00 485840.00 AT Par 485840.00

Description:- COLOUR LIGHT SIGNALS - Supply of 3/4 aspect Colour light signal complete with Signal post, CIbase, ladder, platform, front staging, CLS unit 3/4 aspect, Anchor bolt, nut washer, Universal lock with key etc

25021093 2.00 Numbers 30514.00 61028.00 AT Par 61028.00

Description:- COLOUR LIGHT SIGNALS - Supply of Junction type route indicator (1 way) along with OFF Setbracket and Universal Lock with key. RDSO Spec.No.SPN/194/2006 Rev.2.0 or latest

26021094 2.00 Numbers 40684.00 81368.00 AT Par 81368.00

Description:- COLOUR LIGHT SIGNALS - Supply of Junction type route indicator (3 way) along with OFF Setbracket and Universal Lock with key. RDSO Spec.No.SPN/194/2006 Rev.2.0 or latest

27

021095 7.00 Numbers 12990.00 90930.00 AT Par 90930.00




27Description:- COLOUR LIGHT SIGNALS - Supply of Independent shunt signals complete with post, surface base,position light shunt signal unit, Anchor bolts & Universal lock with key (hand cuff)

28021096 18.00 Numbers 7784.00 140112.00 AT Par 140112.00

Description:- COLOUR LIGHT SIGNALS - Supply of dependent type position light shunt signal unit along withOFF-set bracket, universal lock with key etc.

29021097 10.00 Numbers 4034.00 40340.00 AT Par 40340.00

Description:- COLOUR LIGHT SIGNALS - Supply of Calling on Signal Unit as per RDSO drg. No. S-23468 &fixing arrangement having RDSO drg No. SA-24351 (adv) alt1 along with Universal lock with key etc.

30

021101 26.00 Numbers 10970.00 285220.00 AT Par 285220.00

Description:- Supply of AC Lit LED Signal lighting Unit for Main Signal as per RDSO /SPN/199/2010 rev 1.0 orlatest RDSO specificatrion shall be suitable to CLS as per RDSO drg No. SA-23002 & as 23024/M with latestamendment-colour of aspect to be decided based on signalling plan as per requirement - LED signal unit (Red)

31

021102 34.00 Numbers 10970.00 372980.00 AT Par 372980.00

Description:- Supply of AC Lit LED Signal lighting Unit for Main Signal as per RDSO /SPN/199/2010 rev 1.0 orlatest RDSO specificatrion shall be suitable to CLS as per RDSO drg No. SA-23002 & as 23024/M with latestamendment-colour of aspect to be decided based on signalling plan as per requirement - LED signal unit (Yellow)

32

021103 30.00 Numbers 10970.00 329100.00 AT Par 329100.00

Description:- Supply of AC Lit LED Signal lighting Unit for Main Signal as per RDSO /SPN/199/2010 rev 1.0 orlatest RDSO specificatrion shall be suitable to CLS as per RDSO drg No. SA-23002 & as 23024/M with latestamendment-colour of aspect to be decided based on signalling plan as per requirement - LED signal unit (Green)

33021111 74.00 Numbers 7145.00 528730.00 AT Par 528730.00

Description:- Supply of AC 110V Lit LED signal lighting Unit as per RDSO/Spn/153/2011 rev4.1 or latest RDSOspecification for - Shunt Signal

34021112 10.00 Numbers 7145.00 71450.00 AT Par 71450.00

Description:- Supply of AC 110V Lit LED signal lighting Unit as per RDSO/Spn/153/2011 rev4.1 or latest RDSOspecification for - Calling-ON Signal

35021113 42.00 Numbers 7145.00 300090.00 AT Par 300090.00

Description:- Supply of AC 110V Lit LED signal lighting Unit as per RDSO/Spn/153/2011 rev4.1 or latest RDSOspecification for - Route Indicators

36021121 19.00 Numbers 84918.00 1613442.00 AT Par 1613442.00

Description:- POINT MACHINE - Supply of Electrical point operating machine - IRS Type, 143 mm throw withlock & detector slides, Cable terminal box etc. with suitable ground connection

37021131 45.00 Numbers 20829.00 937305.00 AT Par 937305.00

Description:- Location box - Supply of Location Box-Full Case complete with E Type lock, Hylam sheet, Universallock with key.

38021132 20.00 Numbers 16803.00 336060.00 AT Par 336060.00

Description:- Location box - Supply of Location box - Half Case complete with E Type lock, Hylam sheet,Universal lock with key.

39021133 1550.00 Numbers 271.00 420050.00 AT Par 420050.00

Description:- Location box - Supply of ARA Terminal blocks with links- 6 way

40021134 1000.00 Numbers 86.00 86000.00 AT Par 86000.00

Description:- Location box - Supply of 4-conductor modular Terminal - WAGO/PHOENIX type

41021141 4.00 Numbers 61694.00 246776.00 AT Par 246776.00

Description:- Miscellaneous Items - Supply of Office furniture set for Relay Room consisting of Chairs, Officetable, Airy revolving & tilting cushion chair ,steel almariah, steel stool of Godrej make or similar

42021142 10.00 Numbers 3352.00 33520.00 AT Par 33520.00

Description:- Miscellaneous Items - Supply of Electronic Magneto telephone desk type

43021143 20.00 Numbers 763.00 15260.00 AT Par 15260.00

Description:- Miscellaneous Items - Various types of markers as:-P/C/G/A/IB markers

44021144 4.00 Set 9101.00 36404.00 AT Par 36404.00

Description:- Miscellaneous Items - Supply of Tools for testing - Digital multimeter of Fluke make - 1No, Digitalclamp type AC & DC Ampere Meter - Fluke make- 1.

45021145 2.00 Set 114410.00 228820.00 AT Par 228820.00

Description:- Miscellaneous Items - Supply of Maintenance Tool Kit complete as per List attached

021151 2.00 Numbers 243992.00 487984.00 AT Par 487984.00




46Description:- Voice frequency cable repeater - Supply of 4wire 5way voice frequency cable repeater stationequipment along with rack, U link panel, isolation transformers and power supply including battery charger withmaintenance free battery, each repeater equipment rack will be equiped with five equilizer amplifiers, isolationtransformer for five cicuits & with two number of way station telephones with each circuit with push button typetelephone as per RDSO/Spec/TC/50/90 version 4 or latest RDSO specification. It also include 8way inter-communication card as per section 7 of specifications

47

021163 5.00 Numbers 6689.00 33445.00 AT Par 33445.00

Description:- 6 quad work (Control and way stn equipment - Supply of 4W Way Station equipment with DTMFsignalling to RDSO Specification no. RDSO / SPN / TC / 60 / 2007 or latest RDSO specification with telephone tospecification TC 38/97 or latest RDSO specification

48021164 5.00 Numbers 5234.00 26170.00 AT Par 26170.00

Description:- 6 quad work (Control and way stn equipment - Supply of power supply for telecomm installation atway side station equipment as per tec spec Spec IRS TC 72/97 Amdt 1 or latest RDSO specification

49

021165 20.00 Numbers 3186.00 63720.00 AT Par 63720.00

Description:- 6 quad work (Control and way stn equipment - Supply of RDSO approved 4 wire/ 2 wire Light-weight Portable Emergency Control Telephone as per Spec.IRS-TC-78-2001 with the latest amendment 3 orlatest.

50021166 1.00 Numbers 251117.00 251117.00 AT Par 251117.00

Description:- 6 quad work (Control and way stn equipment - Supply of Cable route locator with accessories makeRIDGID, model SR20 or make C-scope model CAT-XD or make 3M model 2220M or similar

51021171 94.00 Numbers 1995.00 187530.00 AT Par 187530.00

Description:- 6 pin Emergency socket - Supply of emergency socket box with socket pin as per RDSOspecification no. IRS: TC/42/87 Amendment 1 or latest RDSO Specification

52021172 94.00 Numbers 837.00 78678.00 AT Par 78678.00

Description:- 6 pin Emergency socket - Supply of 2T VF transformer as per RDSO spec. IRS : TC- 22/76 or latestRDSO specification - for impedance matching transformer 470:600 ohm (for use of telephone in RE area)

53021181 20.00 Numbers 28347.00 566940.00 AT Par 566940.00

Description:- VHF set - Supply of VHF transreciever simplex for mobile 5watt. Motorola model no.GP 328 orsimilar with rechargeable batteries.This will include battery charger and one rechargeable spare battery.

54021182 8.00 Numbers 3438.00 27504.00 AT Par 27504.00

Description:- VHF set - Supply of Spare KNB-26N 2000 mAH Ni-Mh battery suitable for above VHF set 5W

55

021183 2.00 Numbers 38049.00 76098.00 AT Par 76098.00

Description:- VHF set - Supply of VHF transreciever set simplex 25watt Motorola model no GM-338 or similar atway station (SM/ASM office). This shall also include the power supply of the trans-receiver and one BNC for VHFadaptor

56021184 4.00 Kilometre 17323.00 69292.00 AT Par 69292.00

Description:- VHF set - Supply of switch board cable 10 pair for indoor wiring

57021185 4.00 Kilometre 28243.00 112972.00 AT Par 112972.00

Description:- VHF set - Supply of switch board cable 5 pair for indoor wiring

58

021191 92.00 Kilometre 70252.00 6463184.00 AT Par 6463184.00

Description:- OFC work - Supply of permanently lubricated HDPE pipe 40/33mm dia. As per RDSO specificationsno. RDSO/SPN/TC/45/2013 Rev.2.0 or latest RDSO specification if any , suitable for armoured 24 fiber OFC cableincluding its accessories like plastic coupler, end plug, cable sealing plug and end cap etc. as required for theOFC system.

59021192 100.00 Numbers 2128.00 212800.00 AT Par 212800.00

Description:- OFC work - Supply of FCPC to SCPC 10 meter long patch cords with 0db adaptors as TEC specG/OJC-01/03 JAN 99 or latest RDSO specifications.

60

021193 8.00 Numbers 79710.00 637680.00 AT Par 637680.00

Description:- OFC work - Supply of SMPS based battery charger for telecom use of 230VAC/48V, DC-50Ampcapacity using 3 modules of 25 Amps (FR/BC) suitable for 200Ah LM batteries with lightning & surge protection asper specification no. RDSO/SPN/TL/23/99 (Ver 4 or latest). with automatic switching between the modules N=2

61

021194 9.00 Set 72020.00 648180.00 AT Par 648180.00

Description:- OFC work - Supply of 2V/200AH capacity LMLA batteries as per specification no IRS/S/88/2004 orlatest. 24no of cells (01 set) at each station with required no of porceline insulator.The suitable wooden rack forkeeping batteries sall be supplied and it should be painted either two coats acid resistant paint.

62

021195 92.00 Kilometre 14303.00 1315876.00 AT Par 1315876.00




62 Description:- OFC work - Blowing of armoured Optical Fiber Cable into duct by using blowing machine andassociated works, before blowing the duct integrity shall be tested. If any defect shall be found during ductintegrity test, the entire length of HDPE duct from one chamber to another chamber is to be replaced bycontractor at free of cost

63021196 8.00 Numbers 2410.00 19280.00 AT Par 19280.00

Description:- OFC work - Supply of 50pair Krone terminal box complete with mounting arrangements

64021197 8.00 Numbers 1577.00 12616.00 AT Par 12616.00

Description:- OFC work - Supply of Krone terminal box 20 pair complete with mounting arrangements


Schedule C-SCHEDULE-C 18002766.00

1011011 3.00 Set 127354.00 382062.00 AT Par 382062.00

Description:- AXLE COUNTER EXECUTION Installation, wiring, testing and commissioning of New axle countersystem. Outdoor work & Indoor

2011021 2.00 Station 142725.00 285450.00 AT Par 285450.00

Description:- DESIGN AND DRAWING WORK Design and development of outdoor drawings for outdoorsignalling work for new PI/EI/RRI station

3011022 2.00 Per Unit 16629.00 33258.00 AT Par 33258.00

Description:- DESIGN AND DRAWING WORK Preparation of Station Working Rules ,CRS papers etc as practicein Railways for yards /LC gates/IBH (PER APPLICATION=PER UNIT)

4011031 4.00 Per Unit 8254.00 33016.00 AT Par 33016.00

Description:- INDOOR SIGNALLING WORK Erection, Installation of Cable Termination Rack Assembly andTermination of cables(RACK=UNIT)

5011041 2.00 Set 60856.00 121712.00 AT Par 121712.00

Description:- BLOCK INSTRUMENT Installation, wiring & testing of Axle counter based block panel for onecomplete block section

6

011051 2.00 Set 229751.00 459502.00 AT Par 459502.00

Description:- POWER SUPPLY Installation, wiring, testing and commissioning of complete Integrated PowerSupply (IPS) systems including charging of batteries, supply of battery wire, fabrication and fixing offuse/termination board etc.

7011061 1.00 Kilometre 72262.00 72262.00 AT Par 72262.00

Description:- OUTDOOR EXECUTION WORK Excavation of trenches at depth of 1 Mtr deep and 300-mm wideand back filling in the trench after laying of cable along with supply and fixing of cable route marker

8011062 3.00 Kilometre 74232.00 222696.00 AT Par 222696.00

Description:- OUTDOOR EXECUTION WORK Excavation of cable trenches at 1mtr depth of and 300-mm wideacross the track crossing , Level crossing ,platform and refilling.

9011063 1900.00 Metre 138.00 262200.00 AT Par 262200.00

Description:- OUTDOOR EXECUTION WORK Providing chase in hard rock

10011064 1900.00 Metre 53.00 100700.00 AT Par 100700.00

Description:- OUTDOOR EXECUTION WORK Perforation and Fixing of GI pipes on girder bridges, RCC bridges,culverts

11011065 3.00 Kilometre 43467.00 130401.00 AT Par 130401.00

Description:- OUTDOOR EXECUTION WORK Fixing/ laying of DWC/RCC pipes

12011066 244.00 Kilometre 5959.00 1453996.00 AT Par 1453996.00

Description:- OUTDOOR EXECUTION WORK Laying of signaling / power / telecom / quad /OFC cable of varioussizes in trench / tray / ducts / pipes etc.

13011067 4.00 Numbers 4813.00 19252.00 AT Par 19252.00

Description:- OUTDOOR EXECUTION WORK Supply and fixing of 20pair CTB and Termination of Quad/Jellyfilled cable

14011068 2.00 Station 56299.00 112598.00 AT Par 112598.00

Description:- OUTDOOR EXECUTION WORK Testing of point to point insulation / continuity test for all laid outcables, Measuring Parameters and preparing the records

15

011069 92.00 Kilometre 10718.00 986056.00 AT Par 986056.00

Description:- OUTDOOR EXECUTION WORK Laying of HDPE duct in already made trenches and throughDWC/GI/RCC pipes wherever necessary




16011070 200.00 Metre 1242.00 248400.00 AT Par 248400.00

Description:- Horizontal direction Drilling/boring without damage of surface of road/Track formation. The boreshall be 150mm

17

011081 32.00 Per Unit 16200.00 518400.00 AT Par 518400.00

Description:- COLOUR LIGHT SIGNALS Excavation of pit, casting & plastering of concrete foundation for C.L.Signal and for signal ladder, Erection and wiring of complete signals along with supply of Signal number plate,wiring material etc.(SIGNAL=UNIT)

18

011082 7.00 Per Unit 5006.00 35042.00 AT Par 35042.00

Description:- COLOUR LIGHT SIGNALS Excavation of pit, casting & plastering of concrete foundation for shuntsignal, erection and wiring of complete signals along with supply of Signal number plate, wiring material etc.(SIGNAL=PER UNIT)

19011091 19.00 Point 17385.00 330315.00 AT Par 330315.00

Description:- POINT MACHINE Installation, termination, wiring, testing and commissioning of point machineincluding supply of wire, GI bend pipe, insulation sets etc

20

011101 45.00 Numbers 10766.00 484470.00 AT Par 484470.00

Description:- LOCATION BOX Excavation of pit, casting of concrete foundations for Location Box-Single Case,erection of location box, supply of universal lock with key, Lamp holder 2 pin with switch, wiring material, wiring,testing and commissioning (LOCATION BOX=NUMBER)

21

011102 20.00 Numbers 6254.00 125080.00 AT Par 125080.00

Description:- LOCATION BOX Excavation of pit, casting of concrete foundations for Location Box-Half Case,erection of location box, supply of universal lock with key, Lamp holder 2 pin with switch, wiring material, wiring,testing and commissioning(LOCATION BOX=NUMBER)

22011111 97.00 Numbers 48902.00 4743494.00 AT Par 4743494.00

Description:- MISCELLANEOUS ITEMS Supply and installation of maintenance free earthing and bondingsystem as RDSO spec no RDSO/SPN/197/2008 or latest

23011112 8.00 Numbers 19141.00 153128.00 AT Par 153128.00

Description:- MISCELLANEOUS ITEMS Supply & Installation of various boards like BSLB/GWB/SLB board etc

24011113 20.00 Point 3210.00 64200.00 AT Par 64200.00

Description:- MISCELLANEOUS ITEMS Supply of earth Electrode & installation amd connection of earth withequipment(POINT=PER EARTH)

25011114 32.00 Numbers 2897.00 92704.00 AT Par 92704.00

Description:- MISCELLANEOUS ITEMS Supply and Fixing of RE protective screens of signals.

26011121 2.00 Station 44301.00 88602.00 AT Par 88602.00

Description:- PAINTING Painting, Letter writing, Numbering of termination particulars over all Indoor & OutdoorGears at Complete STATION including LC gate

27

011141 2.00 Numbers 38477.00 76954.00 AT Par 76954.00

Description:- Voice frequency cable repeater Installation & commissioning of 4wire, 5way cable repeater at waystation. This includes erection of rack, termination ofc cable on rack, capacitance balancing of cable quads andinstallation of all battery and charger, their wiring and provision of 8way intercommunication at stations. This alsoincludes tapping 230V AC supply from selected supply coming to SM/ASM, all wiring in room shall be donethrough PVC channel of suitable size & installation of 2 wire control telephone. The installation shall be done asper instruction of engineer

28

011151 5.00 Numbers 3729.00 18645.00 AT Par 18645.00

Description:- 6 Quad work (Control and way stn. equipment) Installation & commissioning of 4wire way stationequipment, power supply unit at SP/SSP/Station/TSS/AEN/PWI/SI offices/Residences. The installation of waystation equipment and power supply unit (supply covered under separate item) shall be mounted on MS anglerack. All the materials for installation commissioning of 4W equipment and power supply unit shall be provided bycontractor.

29

011152 8.00 Numbers 2972.00 23776.00 AT Par 23776.00




Description:- 6 Quad work (Control and way stn. equipment) Installation of Emergency socket box includingsocket on the rail post in the section and yard at every one Km distance as per tapping chart supplied by thesurvey team. This will include wiring and termination of quad cable on socket box mounted at 1m height, clampedwith 2nos U-clamps, provision of concrete foundation of rail post in such way that the rail post is one meter abovethe earth level. The concreting shall be in ratio of 1:3:6 of cement, sand and stone chips. The contractor shalljointly test with Railway engineer for its satisfactory operation. This include painting of emergency socket post withalternate yellow and black strips of 6" width and painting of the socket box with grey colour paint and painting ofarrow on the telephone post/cable marker to show the nearest emergency socket as instructed by the engineer atthe site. Railway will supply the rails. Contractor should supply all other materials required. Cutting of rails to therequired size shall be done by contractor. Rail post and MS pipes of required lengths for fixing emergency socketalso be installed by the contractor.

30

011161 140.00 Numbers 13833.00 1936620.00 AT Par 1936620.00

Description:- OFC work Supply and installation of OFC cable joint enclosure as per TEC No.G/OJC-01/03 Jan.99or latest RDSO specification RDSO/SPN/TC/68/2007, Rev 1 or latest and splicing of optical fibre cables (24 fiber)& testing

31

011162 125.00 Numbers 5554.00 694250.00 AT Par 694250.00

Description:- OFC work Excavation for joint pit and provision of joint chamber of 1.2 mtr. width and 0.6 mtr.height with 2 piece cover on Top and bottom cover with holes for drainage with (reinforcement drawing as pertechnical specification).This includes water cooling of chamber, back filling and ramming of trench after laying andconsolidated of soil as well as disposal of soil as per plan as advice by site engineer.

32

011163 4.00 Numbers 147725.00 590900.00 AT Par 590900.00

Description:- OFC work Supply and installation, testing and commissioning of 2 MB programmable PrimaryDigital drop insert Multiplexer (PDMUX) with conference facility as per specification IRS: TC-68/2012 Rev.0Amendment1 or latest RDSO specification fully wired for 30 channels complete with Power supply unit, Remotecontrol supervision facility and all other accessories, installation material, manuals etc. It should have facility toaccommodate data interface cards in multi drop mode and should be able to support card needed for videoconference, installation of managed expandable rack and krone type MDF are covered in the scope of the work.

33011171 9.00 Numbers 49116.00 442044.00 AT Par 442044.00

Description:- Supply and commission of interface cards for 2mb primary drop MUX of item above 4wire, E&M,VF interface cards (8 circuits per card)

34011172 4.00 Numbers 43960.00 175840.00 AT Par 175840.00

Description:- Supply and commission of interface cards for 2mb primary drop MUX of item above SubscriberLoop interface cards (6 circuits per cards)

35011173 11.00 Numbers 31603.00 347633.00 AT Par 347633.00

Description:- Supply and commission of interface cards for 2mb primary drop MUX of item above ISDN interface(Two BRI ports per card)

36011174 4.00 Numbers 38372.00 153488.00 AT Par 153488.00

Description:- Supply and commission of interface cards for 2mb primary drop MUX of item above ExchangeLoop interface cards (6 circuits per cards)

37011175 4.00 Numbers 47102.00 188408.00 AT Par 188408.00

Description:- Supply and commission of interface cards for 2mb primary drop MUX of item above G703, 64kbpsdata interface cards with minimum of 8 ports per card

38

011176 4.00 Numbers 57221.00 228884.00 AT Par 228884.00

Description:- Supply and commission of interface cards for 2mb primary drop MUX of item above Supply,Installation and testing &commissioning including earthing of 42U 19" covered racks for housing SDH & PDMUXequipments, DDF, FMS, MDS using Krone module etc. complete with all fittings wired & equipped with integratedprotection modules for all channels and adequate number of cooling fans, AC/DC distribution panel, U link panels& other hardwares like runway, ladders etc. It should be possible to lock all the equipment with only order wiretelephone remaining outside the rack.The rack should be of APW President/Rittal make. The components of therack are specified below. Broad description of the rack is given below.Rack size 2200(mm) H x 600(mm) W x600(mm) D, fixed side panels 42U x 600(mm) D front glass door plain 42U x 600 (mm) rear MS door palin 42U x600(mm) D levelling screws- 4 nos. Fan directly mounted on top 48V DC 90 CFM- 2nos. Earth connectivity kit- 1no, Cable manager with cable loops- 2 nos

39

011177 20.00 Numbers 29333.00 586660.00 AT Par 586660.00

Description:- Supply and commission of interface cards for 2mb primary drop MUX of item above Supply andinstallation of Rack mounted 24 fiber Fiber Distribution management system (FDMS) part no 1U 24FS 24FPincluding 24 nos 0.2db SC/PC adaptors 24 Nos 900 micron 1.5m SCPC pigtails RDSO SpecificationRDSO/SPN/TC/037-2000 (Rev.3) or latest.

40

011181 2.00 Numbers 166886.00 333772.00 AT Par 333772.00

Description:- SIGNALLING ITEMS Supply and installation of ELDs (12 Channel) as per Spec. No.RDSO/SPN/256/2002.




41

011182 4.00 Kilometre 104712.00 418848.00 AT Par 418848.00

Description:- SIGNALLING ITEMS Excavation trench 0.35M wide and 1.2M deep in all categories of soils suchas black cotton/hard/murram/hardy soft rock. Filling the trench with earth to the level of surrounding ground afterlaying cable. NOTE: Where digging of trench as per specified depth is not possible, the depth can be reduced withthe approval of the engineer incharge and the payment shall be made proportionally.

42011183 3600.00 Numbers 7.00 25200.00 AT Par 25200.00

Description:- SIGNALLING ITEMS Supply and placing of second class bricks of size 225x100x75 mm (9 brickspe rmeter) horizontally breadth wise in the trench after covering the laid cable with soft soil of 50mm thickness.

43

011184 167.00 Numbers 1148.00 191716.00 AT Par 191716.00

Description:- SIGNALLING ITEMS Supply and fixing of RCC cable route marker as per Drg.no SK/12/10 withengraving of signal/telecomm cable one side and zonal Rly on other side as per Railway practice and painting onboth sides of marker with numbering with black paint (colour of the cable route marker paint and numbering maybe changed/decided by site incharge). The markers should be fixed for maximum of 30m to locate the signalling/Telecomm cable path and the marker should be buried in the ground. Wherever track crossing are available,RCC markers are to be provided on both side of the track for easy identification. All required materials (Supply,painting, transportation to the site and fixing) are to be arranged by contractor.

44011185 4.00 Sqm 2533.00 10132.00 AT Par 10132.00

Description:- SIGNALLING ITEMS Supply and fixing of Rubber matting Thickness 2MM as per IS :15652-2006with suitable adhesive material

S.No. ItemCode

Item Qty Qty Unit Unit Rate Basic Value Escl.(%) Amount BiddingUnit

Schedule E-SCHEDULE-E ELECTRONIC INTERLOCKING 40695155.00

01

Please see Item Breakup for details. 29524585.00 AT Par 29524585.00

Description:- Design & Supply of Microprocessor based Electronic Interlocking system complete as per RDSOSpecification RDSO/SPN/192/2005 with latest amendment to suit signalling plan. 110V AC is used for signal lamplighting. The system should have following composition (a) Hot standby designated as system A & System B (min)(b) Centralized EI With relay interface to drive field gears. (c) Dual VDU control terminals. VDU should be 42"driven by industrial grade fanless PC (RDSO TAN STS/E/TAN/3007 dt 02.11.2012) as per clause 5.3 of RDSOSpecification no. RDSO/SPN/192/2005 or latest. (d) Power supply arrangement should be as per RDSO/TAN no.STS/E/TAN/3012 dt.28.08.2014. (e) Synchronization of EI clock and Data logger clock through CMU. (f) Relayrack (g) The communication equipment should include NMS, the specification and details should be submittedalong with the tender offer (h) Should have facility to get linked to Signal Control Centre (if required) (i) Shouldhave capability to interface with interlocked Level crossing gates in block section, IBS/IBH, Automatic BlockSignals and BPAC with object controllers on diversified OFC as per RDSO/TAN no. STS/E/TAN/3008. dt31.03.2013

02


Description:- Supply of essential Spares @ 10% of each cards/ module/PCBs for each EI system supplied underItem '1' subject to a minimum of one and any fractional quantity to be rounded off to next higher digit. The list ofspares required should be certified by OEM. Inspection by RDSO. For full description refer clause No2 technicalspecs for schedule 'E'

03


Description:- Installation, wiring, testing and commissioning of EI equipment & OC equipment supplied videSchedule Item No.'1' including transportation from consignee's/ Contractor's Depot to site. This includes provisionof non-deteriorating fuses, LED fuse blown indicators, termination of interface wires on the CT rack (FTOT) andpainting sleeve particulars. The input and output cables/wires (RDSO approved) used for interface wiring of EIshall be made of twisted pair. This work also includes: i.Provision of communication between Operator VDU andCIU using OFC cables laid in two separate path for each VDU duly supplying communication equipment.ii.Installation of EI Power supply equipment as per RDSO TAN No. STS/E/TAN/3012. iii.Synchronization of EIclock and Data logger clock through CMU. iv.Supply and provision of necessary Class A, B, C and D protection asper RDSO guide lines and Railway practice. v. The contractor shall submit the OEM certificate for the installationas per RDSO prescribed format before commissioning of EI. [Non-deteriorating fuses, LED fuse blown indicators,indoor cable, wire coils, etc. required to wire the various relays and all other miscellaneous materials required forthe work to be supplied by the contractor. Any other materials required for the commissioning of EI shall besupplied by the contractor.] For full description refer clause No 3 of technical specs for schedule 'E'

NS4 2.00 Job 656500.00 1313000.00 AT Par 1313000.00




04 Description:- Supply and provision of special Earthing for EI Equipment as per RDSO Spec. No.RDSO/SPN/197/2008 or latest and as per RDSO letter no. STS/L/SSI/CA/US&S Dt. 26.07.2011 for typical Bonding& Earthing connections for EI and recent RDSO guidelines regarding earthing. This includes Earthing of EIEquipments, Relay racks, power equipments, Lightning & Transient protection and Class-A lightning protectionarrangements etc., to be done along with the supply of all requisite materials to achieve the required earth valueas per signal engineering practice required for the system supplied. Not less than 4Nos. of earth pits as perRDSO Drg. No. SDO/ RDSO/ E&B/001, at an inter distant of not less than 3m to be provided and inter connectedeven though the required earth value as per signal engineering practice required for the system supplied isachieved with less than 4 earth pits. For full description refer clause No 4 of technical specs for schedule 'E'

05

NS5 12.00 Day 5050.00 60600.00 AT Par 60600.00

Description:- Training of Railway personal at OEM factory premises in installation, testing, commissioning,trouble shooting, alteration and repair of EI with supply of hard and soft copies of course modules and workinginstructions.(including boarding and lodging). For full description refer clause No 5 of technical specs for schedule'E' (DAY= MAN DAY)

06

NS6 2.00 Station 252500.00 505000.00 AT Par 505000.00

Description:- Submission of "As Made" documents for E.I: The contractor has to supply six sets of documents asmentioned below along with system details, site installation details/drawings, maintenance manual, operationprocedure in a bound book as per of Railway practice. 'As made' shall be prepared by the Contractor inAUTOCAD 2000 or latest in A3 size. All indoor work details shall be prepared by contractor and submitted toRailways before testing the circuits. On execution of the work, one copy of the 'As made' check print along withsoft copy of the drawings shall be submitted for checking. The final negatives shall be made in tracing sheet (80to 90 gsm) and submitted to Railways for approval. On approval, the contractor shall submit along with thenegatives, six sets of documents duly making neatly bound booklets. Out of 6 sets, 2 sets of drawings and otherplans shall be kept in transparent plastic cover (2 sheets back to back in one plastic cover) and handed over toRailways. Also the contractor has to supply one set of As mades in 'Reproduction Film' and submit the finalAUTOCAD drawing soft copy in CD. The As made shall include the following: (i) Wiring diagrams (Interfacecircuits) (ii) Application program listing (Application logic in ladder form) (iii) Relay/Cable termination particulars(iv) Input/ Output assignment details (v) Relay layout and contact analysis chart (vi) Equipment disposition layout(vii) Details of power supply arrangement (viii) Any other drawing as required by the Railway as per its practice( ix ) All other documentation as per clause No.10 of RDSO specification RDSO/SPN/192/2005 with latestamendment

08Please see Item Breakup for details. 3568878.00 AT Par 3568878.00

Description:- Supply & installation of Automatic Fire detection & Suppression system for Relay Room (Size 7.1Mx 4.6M x 3.5 M Volume 115 m3) as per clause 8 of technical specs for schedule 'E'


Description:- Supply, installation, testing and commissioning of Fuse Fail Alarm system with automatic changeover facility. as per Specifications at clause No 9 of technical specifications for schedule 'E'

S.No. ItemCode


Schedule F-SCHEDULE-F MULTI SECTION DIGITAL AXLE COUNTER (MSDAC) 49686735.00

01

NS1 78.00 Point 578142.00 45095076.00 AT Par 45095076.00

Description:- Supply of Multi Section Digital Axle Counter (MSDAC) complete system (is required in stationsection with dual detection) with required number of central Evaluator & all accessories and final track clearancerelay for each section, detection point, track Side electronics with accessories including detector plates housingfor Track side electronics equipped for Basindadhar & Sangaldan Stations. RDSO/SPN/ 176/ 2013 (Ver.3) withlatest Amend.Inspection: RDSO.

02

NS2 78.00 Point 41170.00 3211260.00 AT Par 3211260.00

Description:- Installation, testing and Commissioning of detection points as per RDSO specification no. RDSO/SPN/ 176/ 2013 (ver.3) or latest Amend. Note: (i) this includes Commissioning of complete MSDAC system., (ii)Required quad cable will be supplied by Rly (POINT= DETECTION POINT)

03

NS3 2.00 Numbers 226007.00 452014.00 AT Par 452014.00

Description:- Supply of MSDAC Tool Kit as per OEM/RDSO a) Portable Data Analyzer (Downloading EventLogger Data for analysis and report generation) - 1 No. b) Pure Sine Wave Digital Multimeter Fluke Make(Model-1871) or Rishab Make (Model-28S) - 1No. c) Train Simulator Mode 11TS267P) - 1 No. d) Extender Card- 1 No. e)Dummy Wheel- 1 No f) Ring Spanner- 1 No. each g) Open End Spanner- 1 No. each h) Socket Spanner withhandle- 1 No. Torque Wrench(Jaicom JPR 65 or equivalent 88NM)- 1 No. j) Screw Driver no.902- 1 No. k) ScrewDriver no.935- 1 No l) Marking Jig for drilling as applicable m) Dummy Load to check Power Supply (Resistive)- 1No.

NS4 1.00 Point 697404.00 697404.00 AT Par 697404.00




04

Description:- Supply o f Digital Axle Counter - Multisection type, conforming t o Spec: RDSO/SPN/176/2005(Ver.3) with latest amendments including the central Evaluator/processor (s), final track clearance relay for eachsection, detection points, mash room housing for Track side electronic equipment with complete assembly andfixing arrangement for each detection point and a l l other accessories fully wired a n d fully equipped for 04detection points and to cater for 01 Block Sections ( 0 4 D P p e r section). The t w o Detection Points (1+1Redundant) a t both ends o f the block section shall b e connected to separate Evaluators, which will be furtherconnected to Evaluators at the other end of the Block Section on separate Quad Cable Pairs/OFC Pairs throughmedia converters/optical modems, s o a s t o have 100% redundancy. The resetting of Axle-counters shall bePreparatory Mode (POINT= DETECTION POINT)

05NS5 1.00 Numbers 230981.00 230981.00 AT Par 230981.00

Description:- Supply of Digital Axle Counter - Multisection type Tool Kit as recommended by OEM.

S.No. ItemCode


Schedule G-SCHEDULE-G 17107448.00

01

NS1 16.00 Numbers 15367.00 245872.00 AT Par 245872.00

Description:- Supply and installation of fixed Box type IP colour night vision Cameras as per RDSO SPEC.No.RDSO/SPN/TC/ 65/2016 Revision 4.0 or latest, at 2 stations on Katra-Dharam section of USBRL (Necessaryenclosures, clamps, fixing arrangements to fix cameras on ceiling, PF shelters, Foot over bridges etc., to besupplied and fixed by the contractor as directed by Railway Engineer at site) (Cameras inspection by Consignee)

02

NS2 4.00 Numbers 114152.00 456608.00 AT Par 456608.00

Description:- Supply and installation of P/T/Z (Pan/Tilt/Zoom) IP colour night vision cameras as per RDSOSPEC.No. RDSO/SPN/TC/ 65/2016 revision 4.0 or latest, at 2 stations on Katra-Dharam section of USBRL(Necessary enclosure, clamps, fixing arrangements to fix cameras on ceiling, PF shelters, foot over bridges etc.,to be supplied and fixed by the contractor as directed by Railway Engineer at site) (Cameras inspection byConsignee)

03NS3 2.00 Numbers 349759.00 699518.00 AT Par 699518.00

Description:- Supply and Installation of Network Video Recorder with 36 CH with HDMI, ONVIF (Minimum of 32TB usable space or higher) (NVR inspection by Consignee)

04NS4 2.00 Numbers 15908.00 31816.00 AT Par 31816.00

Description:- Supply and installation of computer table (to keep work station, monitor, mouse and keyboard) andrevolving chair-Godrej or featherlite or Zuari make.

05

NS5 2.00 Numbers 10033.00 20066.00 AT Par 20066.00

Description:- Supply and installation of 9 U height 19" size covered rack with(1) front side transparent door withlock arrangement (2) cable organisers (3) provision of one number power supply (each consists of 6 Nos x15A/15A multi pin sockets with ON/OFF switch and fuse arrangement) strip HCL or Rittal or APW or presidentmake

06NS6 2.00 Numbers 13256.00 26512.00 AT Par 26512.00

Description:- Supply and installation of 10 port (2 Optical & 8 Electrical Ports) PoE (Access) switch with SFPports.

07

NS7 2.00 Numbers 131714.00 263428.00 AT Par 263428.00

Description:- Supply and installation of 24 port manageable switch L3 type with minimum 12 optical ports, POEports as per RDSO SPEC.NO RDSO/SPN/TC 83/2014 Rev 1.0 amendement 1.0 or latest (Inspection byConsignee)

08

NS8 2.00 Metre 4385.00 8770.00 AT Par 8770.00

Description:- Supply and installation of FMS (12 F) Rack mountable with splicing and termination of OFC cableswith all accessories as per Railway requirement (pigtails and other materials required for work to be supplied bythe contractor)

09NS9 20.00 Numbers 3063.00 61260.00 AT Par 61260.00

Description:- Supply and installation of Copper to Fibre Media converter as per RDSO SPEC. No. Revision 4.0 orlatest (Inspection by Consignee)

10

NS10 2300.00 Metre 20.00 46000.00 AT Par 46000.00

Description:- Supply of STP (Shielded Twisted Pair) CAT-6 cable compliant with EIA/TIA-568-B.2.1 standard forCAT 6 cable as mentioned in RDSO specification No. RDSO specification No.RDSO/SPN/TC/65/2016 Rev 4.0 orlatest (Inspection by Consignee)

11NS11 2300.00 Metre 26.00 59800.00 AT Par 59800.00

Description:- Supply of 12 core metal strengthened outdoor unarmoured Optic Fiber Cable and all accessoriesrequired for installation sudharsan, finolex make

12

NS12 100.00 Metre 181.00 18100.00 AT Par 18100.00




12 Description:- Supply of 3 core 4 Sq.mm multi strand copper conductor, PVC insulated armoured cable of Finolexor reputed make.(Inspection by Consignee)

13NS13 2.00 Numbers 64057.00 128114.00 AT Par 128114.00

Description:- Supply and installation of 3KVA online UPS with suitable batteries for minimum 60 minutes backuptime (APC or numeric make)

14

NS14 230.00 Metre 28.00 6440.00 AT Par 6440.00

Description:- Laying of UTP/OFC cables/power cables in 1" PVC conduit (ISI marked) / case capping and G.Iclamping on wall or rooftops/PF shelters with suitable G.I clamping (PVC conduit/case capping and otheraccessories to be supplied by the contractor)

15

NS15 2070.00 Metre 234.00 484380.00 AT Par 484380.00

Description:- Cutting of trench across/ on the paltform for a depth of 10cm with marble cutting machine and fillingthe trench with concrete and after cable laying and restoring the surface with plaster etc. / trenching in nonconcreted area to a depth of 1 meter, refilling after cable lying and restoring the surface to normal condition etc.

16NS16 230.00 Metre 34.00 7820.00 AT Par 7820.00

Description:- Supply and Installation of 25mm PVC Conduit Pipe

17NS17 6.00 Set 2810.00 16860.00 AT Par 16860.00

Description:- Supply and provision of multi pin power socket with switch 15A/5A (6Nos) wired with 2.5 Sq.mmcopper multi strand wire

18NS18 2070.00 Metre 602.00 1246140.00 AT Par 1246140.00

Description:- Supply and installation of GI pipes (50mm dia-3.65mm thick, IS 1239 part I grade for laying of cableto the PF shelter from ground level and concreting at base level as directed by Railway Engineer

19NS19 40.00 Numbers 154.00 6160.00 AT Par 6160.00

Description:- Supply of OFC patch cords 10 Mtr length

20

NS20 2.00 Lumpsum 31285.00 62570.00 AT Par 62570.00

Description:- Preparation and submission of drawings mentioning the location of cameras, wiring diagrams ofUTP, power cable, OFC cable etc., OTDR reports for OFC cable, earth resistance test reports,Technicaldetails(like bellrock report for servers, storage, work stations etc.,) switches, media converters etc asdirected by Railway Engineer. Submission of Licenses details for operating systems, softwares etc in 6 copies asper station duly binded and two soft copies in CD dor each station as mentioned in Annexure

21NS21 2.00 Lumpsum 54353.00 108706.00 AT Par 108706.00

Description:- Provision of Desktop computer along with TFT, keyboard & mouse

22NS22 3.00 Numbers 16332.00 48996.00 AT Par 48996.00

Description:- B)PA System= Supply of Ahuja make SSA-250M PA Amplifier or similar

23NS23 20.00 Numbers 2007.00 40140.00 AT Par 40140.00

Description:- Supply of reflex horn type speaker Ahuja make or similar UHC 30XT

24NS24 10.00 Numbers 2047.00 20470.00 AT Par 20470.00

Description:- Supply of PA column speakers Ahuja make or similar ASC 20T

25NS25 3.00 Numbers 2222.00 6666.00 AT Par 6666.00

Description:- Supply of microphone Ahuja make AGN-500 or similar

26NS26 3.00 Numbers 183.00 549.00 AT Par 549.00

Description:- Supply of microphone stand Ahuja make ATS-5 or similar

27NS27 2000.00 Metre 58.00 116000.00 AT Par 116000.00

Description:- Supply of speaker cable 2 core PVC sheathed & screened of size 47/0.193 as per IS-694 or latestRDSO specification

28

NS28 2000.00 Metre 46.00 92000.00 AT Par 92000.00

Description:- Supply & laying of GI wire 8SWG overhead for twin cable multi strand copper screened cable(Bobbin of insulating material like china clay,rubber plastic should be used for taking GI wire & twin core cabletogether. Bobbins, GI wire to be supplied by contractor

29NS29 20.00 Numbers 671.00 13420.00 AT Par 13420.00

Description:- Fixing of Horn type speakers on GI post using clamps & nut bolts with cover for unit of speaker toprotect them from rain/snow fall etc. (Nut, bolts & cove to be supplied by contractor)

30

NS30 10.00 Numbers 58.00 580.00 AT Par 580.00

Description:- Fixing of box type speakers on wall with fixing clamp arrangement with nut Fixing of box typespeakers on wall with fixing clamp arrangement with nut bolt/screw. Clamp/nut-bolts/screw etc.are to be suppliedby contractor. bolt/screw. Clamp/nut-bolts/screw etc.are to be supplied by contractor.

31

NS31 2.00 Numbers 58479.00 116958.00 AT Par 116958.00




31 Description:- Supply of UPS online 2-KVA, 120min Backup make APC/Numeric/Emersonor superior (Inspection-Consignee).

32

NS32 1600.00 Metre 31.00 49600.00 AT Par 49600.00

Description:- Drawing of PVC sheathed cable in PVC conduit pipe/casing, PVC pipe of 20mm (external dia)thickness 1.5mm medium density fit for electrical purpose as per IS 9537 & other fixing material to be supplied bycontractor. Cable will be supplied by Railway.(RMT = Metre)

33

NS33 2.00 Numbers 19718.00 39436.00 AT Par 39436.00

Description:- Supply of metal enclosure (19" rack 22U Audio Equipment Rack) made of dia extrusion Aluminiumand caster wheels to house two amplifier and UPS with individual locking facility & also with 4 nos. of 3/5 pin 5ASocket including internal wiring

34NS34 2.00 Numbers 61411.00 122822.00 AT Par 122822.00

Description:- GPS Clock Supply of 16 port Master clock with GPS reciever as per RDSO specificationRDSO/SPN/TC@ 47>47 2008

35NS35 4.00 Numbers 45677.00 182708.00 AT Par 182708.00

Description:- Supply of 4 digit double sided platform clock ( white LED) as per RDSO specificationRDSO/SPN/TC@ 47>47 2008

36NS36 1000.00 Metre 198.00 198000.00 AT Par 198000.00

Description:- Supply of 3 Core Power Cable, 2.5 Sq mm with 1 " PVC Conduit

37NS37 1000.00 Metre 34.00 34000.00 AT Par 34000.00

Description:- Supply of 5 pair 0.5mm dia colour coded data communication cable

38NS38 2.00 Numbers 5050.00 10100.00 AT Par 10100.00

Description:- Installation of Master clock

39NS39 4.00 Numbers 5050.00 20200.00 AT Par 20200.00

Description:- Installation of Double sided clock

40NS40 26.00 Numbers 59590.00 1549340.00 AT Par 1549340.00

Description:- IPIS Supply of LED based single line double face coach indication display board with all necessaryaccessories as per RDSO Spech.No.RDSO/TC/61/2015 rev.4 or latest (Inspection-RDSO).

41NS41 1.00 Numbers 1004950.00 1004950.00 AT Par 1004950.00

Description:- Supply of LED based 5 lineTrain indication board (single face) with all necessary accessories asper ROSO Spech.No.RDSO/SPN/TC/61/2015 rev.4 or latest (Inspection-RDSO).

42

NS42 1.00 Numbers 298960.00 298960.00 AT Par 298960.00

Description:- Supply of Control Console unit complete (Including driving software for train indication, coachindication & Auto-Announcement system) conforming to RDSO Spech.No. RDSO/TC/61/2015 rev.4 or latest(Inspection-RDSO).

43NS43 1.00 Numbers 64640.00 64640.00 AT Par 64640.00

Description:- Supply of 16 port Main Data Communication Hub (MDCH) conforming to RDSOSpech.No.RDSO/TC/61/2015 rev.4 or latest (Inspection-Consignee).

44NS44 1.00 Numbers 64640.00 64640.00 AT Par 64640.00

Description:- Supply of 16 port Platform Data Communication Hub (PDCH) conforming to RDSO Spech.No.RDSO/TC/61/2015 rev 4 or latest (Inspection-Consignee).

45

NS45 1.00 Kilometre 92920.00 92920.00 AT Par 92920.00

Description:- Supply of PVC insulated flexible 3 core 2.5sqmm multi strand power cable provided for each of thedisplay boards shall confirm to specification no. IS694:1990 reaffirmed 1995 or latest of reputed brand as perRDSO Spech.No.RDSO/SPN/TC/61/2015 rev 4 or latest (Inspection-Consignee).

46


Description:- Supply of 5 pair PVC insulated twin twisted screened data communication cable as per standardsBIS:5308 PART-1 of reputed brand as per RDSO Spech.No.RODO/SPN/TC/61/2015 rev 4 or latest (Inspection-Consignee).

47NS47 1.00 Numbers 8282.00 8282.00 AT Par 8282.00

Description:- Installation and commissioning of single line double face coach indication display board (Uncoveredarea) as per RDSO Spech.No.RDSO/SPN/TC/61/2015 rev 4 or latest.

48NS48 26.00 Numbers 5555.00 144430.00 AT Par 144430.00

Description:- Installation and commissioning of single line double face coach indication display board (coveredarea) as per RDSO Spech. No. RDSO/61/2015 rev.4 or latest.

49

NS49 1.00 Numbers 110090.00 110090.00 AT Par 110090.00




49 Description:- Fabrication, supply and installation of mechanical structure including required all necessaryaccessories for the 5line display board (single face) to be installed in open area in the railway station premises. Itshould have rain hood protection to protect display board from weather condition at station as per RDSO spec.noRDSO/SPN/TC/61/2015 rev 4 or latest.

50NS50 1.00 Numbers 8080.00 8080.00 AT Par 8080.00

Description:- Installation of full redundant Control Console unit complete (lncluding driving software for train,contact and indication & Auto Announcement) as per RDSO Spech.No.RDSO/SPN/TC/61/2015 rev 4 or latest.

51NS51 2.00 Numbers 5050.00 10100.00 AT Par 10100.00

Description:- Installation and commissioning of 16 port Main Data Communication Hub (MDCH) & Platform DataCommunication Hub (PDCH) conforming to RDSO Spech.No.RDSO/SPN/TC/61/2015 rev 4 or latest

52NS52 1.00 Kilometre 13130.00 13130.00 AT Par 13130.00

Description:- Laying of different type cables in the trench.


Description:- Supply and Fixing of PVC pipe / casing caping of different size as per requirement of site for cable


Description:- Cutting of trench on PF or across the PF 10 cm depth and restore the surface inprivious positionafter laying pipe and cable

55NS55 1.00 Numbers 58479.00 58479.00 AT Par 58479.00

Description:- Supply of UPS online 2-KVA, 120min Backup make APC/Numeric/Emerson or reputed brand(Inspection-Consignee).

56NS56 1.00 Numbers 227250.00 227250.00 AT Par 227250.00

Description:- Supply of LED based Coach Guidance at a glance display board with all necessary accessories asper RDSO Spec.no. RDSO/SPN/TC/61/2015 rev 4 or latest.(Inspection-Consignee)

57NS57 1.00 Numbers 19190.00 19190.00 AT Par 19190.00

Description:- Installation and commissioning of LED based Coach Guidance at a glance display board with allnecessary accessories as per RDSO spec.no.RDSO/SPN/TC/61/2015 rev 4 or latest.

58NS58 2.00 Numbers 99015.00 198030.00 AT Par 198030.00

Description:- UTS/PRS Supply of Router (02 x LAN + 04 x 02 Mbps WAN Ports)

59NS59 2.00 Numbers 18851.00 37702.00 AT Par 37702.00

Description:- Supply of 24 port layer - 2 Switch

60NS60 4.00 Numbers 11296.00 45184.00 AT Par 45184.00

Description:- Supply of 02 Mbps Modems (in pair)

61NS61 2.00 Numbers 110242.00 220484.00 AT Par 220484.00

Description:- Supply of NTS- Network terminal Server 8x RS232 with TxD, RxD, DTR, DSR, RTS, CTS, DCD withRJ-45 connector, supporting speed upto 19.2 kbps on each port simultaneously.

62

NS62 5.00 Numbers 30299.00 151495.00 AT Par 151495.00

Description:- Supply of ThinClient version of Dumb terminal with DEC VT 320 emulation with VT200/220compatible, Railways UTS and PRS form downloadable capability with ansback support with 15.6 inch LCDmonitor, DECVT220 style keyboard

63NS63 5.00 Numbers 12508.00 62540.00 AT Par 62540.00

Description:- Supply of UTS Dot Matrix Ticket Printers (Make/Brand EPSON LX-300 +II RTP)

64NS64 2.00 Numbers 58479.00 116958.00 AT Par 116958.00

Description:- Supply of UPS online 2-KVA, 120min Backup make APC / Numeric / Emersonor superior(Inspection-Consignee).

65NS65 2.00 Numbers 3232000.00 6464000.00 AT Par 6464000.00

Description:- Baggage Scanner- Supply Of X-Ray Baggage Screening System as per RDSO Specification NoRDSO/SPN/TC/94/2010 Rev-1.0 as per clause 4.0 or latest, with Tunnel size - minimum 1000mm x 1000mm.

66

NS66 2.00 Job 323200.00 646400.00 AT Par 646400.00

Description:- Installation, Testing, Commissioning Of X-Ray Baggage Screening System Including Training ofRPF / Railway Personnel under Integrated Security System should be done with provision of system Integrationwith CCTV System including installed ones as well as other Security Items under Integrated Security System withWarranty period of three 03 years from date of commissioning of whole system, including site preparation,electrical wiring and fitting all the sub-assemblies like belt/roller/monitor.





Schedule A1-SCHEDULE-A1 3689331.00

1041011 3.00 Numbers 212498.00 637494.00 AT Par 637494.00

Description:- ScheduleA1 Axle counter tool kit

2041012 3.00 Set 57247.00 171741.00 AT Par 171741.00

Description:- ScheduleA1 Supply of Web detector (each set consists of 2 nos. of TX and 2 nos. of RX coils) forAnalog/Digital axle counters

3

041013 3.00 Set 960032.00 2880096.00 AT Par 2880096.00

Description:- ScheduleA1 Supply of High Availability Single section Digital Axle Counter System complete withdual sensor as per RDSO specification No.RDSO/SPN/177/2012 with version 3 or latest complete in all respectincluding reset box. It shall have dual sensors.

S.No. ItemCode


Schedule D1-SCHEDULE-D1(NON SOR) 81127354.00

01NS1 30.00 Numbers 7559.00 226770.00 AT Par 226770.00

Description:- Supply of QBCA1 contactor relay


Description:- Indoor Signalling cable

03NS3 2.00 Numbers 23451.00 46902.00 AT Par 46902.00

Description:- Supply of Annunciator (10 lines) for Push Button Magneto Telephones

04NS4 2.00 Pair 43935.00 87870.00 AT Par 87870.00

Description:- Supply of Automatic Media Change over system of Modem working on redundant channels for datatransmission on OFC/Quad

05NS5 2.00 Pair 77619.00 155238.00 AT Par 155238.00

Description:- Supply of Modem for UFSBI for use with secondary media OFC/Quad the modem shall becompatible with existing system as per RDSO/SPN/147/2005 with amendment-1 or latest.

06

NS6 2.00 Set 544635.00 1089270.00 AT Par 1089270.00

Description:- Supply of network datalogger of 1024 digital and 32 Analog inputs for monitoring status ofimportant relays complete with procceessor module monitor, following inputs, as per specificationRDSO/SPN/99/06 with latest ammendment including power supply of adequate capacity, Battery and faultdiagnostic software for failure analysis. complete datalogger and proccessor module (Computer as Annexure-3shall be placed in president Rack of suitable size to be supplied. This also includes supply of 1No. compositecomputer and printer table godrej work station table) for keeping proccessor module and 1 No. Godrej makeoperater chair model -PCH 7001 or simillar make godrej.


Description:- Supply of Spare cards for Single/Double line UFSBI as per RDSO/SPN/147/2005 with latestamendments), to suit supply item no 38553 a & b in this schedule and for item at S.No 06

08

NS8 3.00 Pair 144546.00 433638.00 AT Par 433638.00

Description:- Supply of Industrial Grade E1 interface inbuilt media redundancy and auto switch over on Quadand RS 232, having unique addressing for over for each pair for UFSBI system compatible with all RDSOapproved firms

09NS9 6.00 Numbers 8160.00 48960.00 AT Par 48960.00

Description:- Portable fire extinguisher foam type capacity (09 Lltr)

10NS10 6.00 Numbers 7515.00 45090.00 AT Par 45090.00

Description:- Portable fire extinguisher Dry Chemical Powder (10Lltr)

11

NS11 2.00 Numbers 58146.00 116292.00 AT Par 116292.00

Description:- Supply of Multi Lamp Route Indicator (LED) single digit from from 1-9 with white LED with housingrack with white LED along with housing rack and I/P voltage 110+_20% Volts, current 25MA +-%, visibility of400Mtrs (Minimum) with specification RDSO/SPN/153/2014/ revised item No.5

12NS12 2.00 Set 520098.00 1040196.00 AT Par 1040196.00

Description:- Supply Diesel Generator Set - 25 KVA Single phase, 230 Volts 50HZ. along with battery, canopyand control panel (Air cooled silent DG Set (CPCB 2 complaint) as per Annexure for DG set

13NS13 300.00 Numbers 105.00 31500.00 AT Par 31500.00

Description:- Supply of Fuse Block for HRC fuse as per Specn.No.SA 23748/IR.


Description:- NS-14 Supply of Fuses of various capacity




15

NS15 240.00 Metre 236.00 56640.00 AT Par 56640.00

Description:- Supply of 3 & 1/2 core, 35 sqmm LT cable, 1.1KV grade, stranded Aluminum conductor, PVCinsulated and sheathed armoured as per IS 1554/latest. Approved makes Incab, fort gloster, NICCO, Bharat cabAsia, Finolex.

16NS16 2.00 Numbers 87065.00 174130.00 AT Par 174130.00

Description:- POWER SUPPLY- Supply of change over panel 63 Amps with all indication with LED and meterswith 3-way rotary switch with separate MCB

17NS17 2.00 Numbers 20265.00 40530.00 AT Par 40530.00

Description:- Supply of remote panel for DG sets with all indications

18

NS18 1.00 Set 647669.00 647669.00 AT Par 647669.00

Description:- Solar Power- Supply of Solar Photovoltaic System as per RDSO specs IRS-S-84/92 or latest RDSOspecification for charging the lead acid battery 110V/300AH with Charge Controller of 60A capacity to cater thesteady load of signaling System

19

NS19 1.00 Set 665893.00 665893.00 AT Par 665893.00

Description:- Supply of Solar Photovoltaic System as per RDSO specs IRS-S-84/92 or latest RDSO specificationfor charging the lead acid battery 110V/300AH with charge controller of 100A capacity to cater the steady load ofsignaling system.

23


Description:- CABLE Low Smoke Zero Halogen (LSZH) - Supply of Cable U/S PVC insulated armoured PVCsheathed for under ground usage of the following sizes confirming IRS -S-63/2014 (Rev.4.0) Supply of LSZH 12Core x 1.5 Sq.mm

24


Description:- CABLE Low Smoke Zero Halogen (LSZH) - Supply of Cable U/S PVC insulated armoured PVCsheathed for under ground usage of the following sizes confirming IRS -S-63/2014 (Rev.4.0)- Supply of LSZH 2Core x 4 Sq.mm (Cu)


Description:- Supply of LSZH Supply of under ground Jelly filled 0.9 mm dia 6 quad cable with IRS spec. No.IRS: TC/30/2005 Amndt -2 or latest.DOC.No.RDSO/SPN/TC/72/07.

26


Description:- CABLE Low Smoke Zero Halogen (LSZH) - Supply of Cable U/S PVC insulated armoured PVCsheathed for under ground usage of the following sizes confirming IRS -S-63/2014 (Rev.4.0)- Supply of LSZH 12x 2.5Sq.mm (Copper)

27


Description:- CABLE Low Smoke Zero Halogen (LSZH) - Supply of Cable U/S PVC insulated armoured PVCsheathed for under ground usage of the following sizes confirming IRS -S-63/2014 (Rev.4.0)- Supply of LSZHPower cable 2 x 25Sq.mm (Al)


Description:- Supply of 48 Fiber armoured OFC Cable (LSZH) as per IRS:TC 55-2006 with latest Amendment1.1 or latest.


Description:- Supply of 24 Fiber armoured OFC Cable (LSZH) as per IRS:TC 55-2006 with latest Amendment1.1 or latest.


Description:- Supply of Underground Jelly filled 1.4mm dia 6 Quad Cable LSZH outer Sheath generally as perIRS Spec.no.IRS: TC 72-2007 or latest.


Description:- Supply of Cable Un-Screen PVC insulated armoured PVC sheathed for under ground usage of thefollowing sizes-

32NS32 6.00 Numbers 8787.00 52722.00 AT Par 52722.00

Description:- Supply of Offset bracket 5 1/2 " dia for signal and route

33NS33 800.00 Metre 94.00 75200.00 AT Par 75200.00

Description:- Supply of Telecom Indoor Cables 20 pair as per TEC Spec.

34NS34 1200.00 Metre 44.00 52800.00 AT Par 52800.00

Description:- Supply of Telecom Indoor Cables 10 pair as per TEC Spec.

35NS35 400.00 Metre 6.00 2400.00 AT Par 2400.00

Description:- Supply of Telecom Indoor Cables 2 pair as per TEC Spec

36NS36 2.00 Set 162799.00 325598.00 AT Par 325598.00




36Description:- Supply of equipment's- Tool kit for MSDAC as per annexure

37NS37 4.00 Numbers 5361.00 21444.00 AT Par 21444.00

Description:- Supply of hand operated Track drilling Machine for bonding

38NS38 4.00 Numbers 4334.00 17336.00 AT Par 17336.00

Description:- Supply of Electric Drilling Machine 13mm impact CAT.No.KPT/563 power input 550W,no loadspeed 1200rpm,drilling capacity 13/25/10 KPT make r similar

39NS39 3.00 Numbers 4141.00 12423.00 AT Par 12423.00

Description:- Supply of Train Shunt Meter

40NS40 1.00 Numbers 90298.00 90298.00 AT Par 90298.00

Description:- Supply of Cable fault locator for all type of fault of telemetric or stanley or Andig make with 16 KMrange

41

NS41 1.00 Numbers 201122.00 201122.00 AT Par 201122.00

Description:- Supply of Cable route locator kit comprising of a)CAT-33 XD cable avoidance tool, stand aloneequipment for cable locating & avoidance. B) SVG signal generator & accessories c) Signal clamp of 3M Stanleyor Radiotronics make

42NS42 1.00 Numbers 6712.00 6712.00 AT Par 6712.00

Description:- Supply of Earth Resistance Tester, dual range 10/100 Ohm digital display with complete earthtesting kit.

43NS43 2.00 Numbers 25866.00 51732.00 AT Par 51732.00

Description:- Supply of TMS kit. (IRS-TC-43/87)

44NS44 3.00 Numbers 7727.00 23181.00 AT Par 23181.00

Description:- Supply of Digital Insulation tester/Megger 100V, 500v,1000v, 2500v and 0-20000 Mega Ohms withaccessories.

45NS45 3.00 Pair 22725.00 68175.00 AT Par 68175.00

Description:- E1 to Ethernet Convertor (Extending the link to SP/SSP/TSS from Station)

4646 1.00 Numbers 228569.00 228569.00 AT Par 228569.00

Description:- Supply of OTDR

47NS47 1.00 Numbers 331969.00 331969.00 AT Par 331969.00

Description:- Supply of OFC Cable splicing machine.

48NS48 1.00 Numbers 26122.00 26122.00 AT Par 26122.00

Description:- Supply of Optical power meter.

49NS49 1.00 Numbers 65305.00 65305.00 AT Par 65305.00

Description:- Supply of Optical Source meter.

50NS50 1.00 Numbers 56065.00 56065.00 AT Par 56065.00

Description:- Supply of E1 tester / Analyzer (Fluke make)

51

NS51 1.00 Set 14424.00 14424.00 AT Par 14424.00

Description:- Supply of OFC tool kit as per TEC.Spec. no.G/OFT-01/02 Mar.99 or latest. It contains: Ratchetscrew driver, measuring scale, Hack saw (junior) with blades, Scissor ,Tweezer, Cutting nipper, Strip Nose, Plier,Hammer, adjustable spanner, cable Knife, cable cutter, Cable sheat & Jacket remover, Seramic type FRP cutter,Fiber stripper for primary coating, Fibre Stripper for secondary coating, consumable items ( Emry cloth, PVCadhesive tape, Lab grade isopropane, Lab Grade Hexane, Ethyl Alcohol, Tissue paper, cotton buds, torch withcell, Tool Box

52NS52 4.00 Numbers 6839.00 27356.00 AT Par 27356.00

Description:- Supply of surge suppressor for all the 30 circuits derived from primary MUXs (Z-protection)complete as per technical specifications and other stipulations of tender document

53

NS53 2.00 Numbers 565873.00 1131746.00 AT Par 1131746.00

Description:- SDH & exchange= Supply of Coral IVRS IVDX telephone exchange for MCC card- 02nos, Analogextension- 96Nos, E1/PRI card- 02Nos, DCC-8 card- 2Nos, IRIS IVDX 512 port cabinet, 200 pair MDF with kronemodule

54NS54 200.00 Numbers 34.00 6800.00 AT Par 6800.00

Description:- Supply of lighning dischage suitable for krone type module for protection against over voltage &current for electronic telephone exchange.

55NS55 60.00 Numbers 702.00 42120.00 AT Par 42120.00

Description:- Supply of DTMF type two wire Push button Auto Telephone.

57

NS57 2000.00 Metre 16.00 32000.00 AT Par 32000.00




57Description:- Supply of UTP CAT-6 data cable for computer networking as per RDSO/SPN/TC/65/2016 Rev.4 orlatest

58NS58 40.00 Numbers 253.00 10120.00 AT Par 10120.00

Description:- Supply of CAT6 IO, face plate, Wall box

59NS59 6.00 Numbers 151900.00 911400.00 AT Par 911400.00

Description:- Supply of L3 Switch as per specification

60NS60 4.00 Numbers 24157.00 96628.00 AT Par 96628.00

Description:- Supply of L2 Switch

61NS61 3.00 Set 16754.00 50262.00 AT Par 50262.00

Description:- Supply of MDF crone frame and IPM 100 pair

62NS62 4.00 Numbers 570.00 2280.00 AT Par 2280.00

Description:- Supply of IDC Punching tool of Krone make or similar

63NS63 60.00 Numbers 12.00 720.00 AT Par 720.00

Description:- Supply of Rozet for single line telephone

64NS64 2.00 Numbers 14524.00 29048.00 AT Par 29048.00

Description:- Supply of wrapping wire gun

65NS65 2.00 Numbers 416.00 832.00 AT Par 832.00

Description:- Supply of unwrapping wire tool

66

NS66 3.00 Numbers 95059.00 285177.00 AT Par 285177.00

Description:- Supply of local craft terminal with intel core i7 processor, 8GB RAM, 1TB HDD or similar to HPmake model Envy M7K211dx with all accessories preloaded with windows operating system compatible to load &operate the NMS for SDH & PDMUX equipment. Item to be supplied with minimum 2 years warranty from OEM.

67

NS67 40.00 Numbers 11110.00 444400.00 AT Par 444400.00

Description:- Supply of DP Box MS sheet thickness 2mm and dimensions 1.2 x 1.2 x 0.2 mtrs includingfabrication transportation .Antirust painting and fixing at site with appoved anchor bolts for 6 Quad cable jointplacing in tunnels.

68NS68 2.00 Numbers 2020.00 4040.00 AT Par 4040.00

Description:- Supply of Furniture's= Office chairs with arms with cushioned back rest and seat

69NS69 2.00 Numbers 6721.00 13442.00 AT Par 13442.00

Description:- Computer Table Godrej make model no C-1

70NS70 2.00 Numbers 4545.00 9090.00 AT Par 9090.00

Description:- Steel Almirah

71NS71 2.00 Numbers 8093.00 16186.00 AT Par 16186.00

Description:- Aluminum Straight Ladder Extensive ( 11 M)

72NS72 900.00 Metre 162.00 145800.00 AT Par 145800.00

Description:- Supply of SPLIT RCC pipes of size 150mm dia, 2 mtr long along with collars


Description:- Supply of spare cards for HA-SSDAC Axle counter to suit for supply item no 36107 in schedule A1

74NS74 3.00 Numbers 29694.00 89082.00 AT Par 89082.00

Description:- Supply Redundant 650W AC Power Supply for ISR

75NS75 8.00 Numbers 59091.00 472728.00 AT Par 472728.00

Description:- Supply 1000BASE-LX/LH SFP transceiver module, MMF/SMF, 1310nm, DOM (Make Cisco orsimilar)

S.No. ItemCode


Schedule D2-SCHEDULE-D2 (NON SOR) 516269955.00

01

NS1 10.00 Numbers 10036.00 100360.00 AT Par 100360.00

Description:- Supply and installation of KEY LOCK RELAY (KLCR) working on 24V DC ACI type TMA withdifferent ward combination IRS-S-46, IRS-S@ 45"44 IRS-23 as applicable "INTEGRA Make" with contactsconfiguration 4F-4B (TMA 1144/116 IM-OLO)

02

NS2 100.00 Numbers 6237.00 623700.00 AT Par 623700.00




02 Description:- Supply & Installation of lightning cum surge protection safety device with visual indication, pluggableand testable with surge tester and potential free contact. Outputs suitable for 110 V AC applications (Conformingto RDSO Spec. RDSO/SPN/165/2012 or latest and as per IEC 61643) it also includes installation of SurgeProtection Device duly wired mounted on DIN rail with necessary fittings like nuts, bolts etc. as per siterequirement

03NS3 2.00 Numbers 34608.00 69216.00 AT Par 69216.00

Description:- Supply and installation Demineralization Plant of Capacity-65 Ltr per hour approx. This includes allthe type of connections from water sources to unit and collection unit.

04NS4 4.00 Numbers 3941.00 15764.00 AT Par 15764.00

Description:- Supply and fixing of RE protective Screens of expanded metals 12SWG of size 1200 x 1500 mm onsignals as per extent pratice & as per instructions

05NS5 2.00 Numbers 16968.00 33936.00 AT Par 33936.00

Description:- SDH & Exchange= Installation & commissioning of Coral IVRS IVDX telephone exchange

06

NS6 7.00 Numbers 363658.00 2545606.00 AT Par 2545606.00

Description:- Supply and installation of Managed STM-4 ADM equipment as per technical specification no.TECGR No. GR/TX/SDH/-010/03 Jan 2011 or latest with 3 nos. STM-4 aggregate Optical interface and 3 nos. STM-1(S1.1) aggregate optical interface, 63 E1s and minimum 8 nos. of 10/100 base T Ethernet port, orderwire, powersupply unit, sub rack, DDF, installation materials manuals and others accessories. the equipment should be fullywired for its ultimate capacity and provide redundancy for power supply and synchronization. it shall be possible touse the full capacity of the equipment by adding additional tribtary cards.

07

NS7 7.00 Lumpsum 12451.00 87157.00 AT Par 87157.00

Description:- Installation and wiring of SDH / STMs equipment with all accessories, 19" rack, DDF for E1s, layingof cables on runway ladder, wiring of rack MCBs as per direction of engineer / in-charge. Supply of cable runway,MCBs are accommodated in separate items as supply. Inspection by Consignee.

08NS8 1.00 Numbers 37762.00 37762.00 AT Par 37762.00

Description:- Supply, installation of Automatic Radio patching equipment for end patching of 6 VF Circuits as perRDSO Specification no. RDSO / SPN / TC / 66 / 2007 revision 0.0 with Amendment 3 or latest.

10NS10 1600.00 Metre 83.00 132800.00 AT Par 132800.00

Description:- Supply and routing of PVC multi stand copper cable of 6 sq.mm for connecting various equipmentsand lightening protection devices to equi-potentialbus bar. Inspection by Consignee.

11NS11 3.00 Numbers 144194.00 432582.00 AT Par 432582.00

Description:- Supply Installation wiring & Commissioning of 5 KVA UPS (this includes supply of 7/20 power cableand 10 Nos of 15Amp capacity suitable for 230V AC Anchor make Power point)

12

NS12 12.00 Numbers 388.00 4656.00 AT Par 4656.00

Description:- Supply and installation of 10 pair DP Boxes and Termination of cables as per Specification no.Specification no. RDSO/SPN/TC/97/2012 or latest. Execution as per site engineer. Material to be supplied, shall beinspected by RDSO approved source & certificate to be issued by the manufacturer to the effect that the materialhas been manufactured as per RDSO specification as mentioned above.

13NS13 3.00 Numbers 530.00 1590.00 AT Par 1590.00

Description:- Supply and installation of 6Q DP with 6Q cable termination facility as per existing Railway practice.

14NS14 100.00 Lumpsum 566.00 56600.00 AT Par 56600.00

Description:- Fixing of EMC box in tunnels along with all accessories

15NS15 8.00 Lumpsum 1994.00 15952.00 AT Par 15952.00

Description:- Installation and wiring of SMPS battery chargers of 230VAC/48V DC, DC-25 Amp capacity as perRDSO spec.TL/23/99 ver.4 or latest , including transportation charges. Inspection by Consignee.

16

NS16 31590.00 Metre 9148.00 288985320.00 AT Par 288985320.00

Description:- Design & Supply of Stainless Steel SS 316 (& conforming to specification detailed at 4 A of SCC part- B) Cable tray of size 200mm x 110mm / 2mm thickness as per approved diagram / drawings. (The design shallbe got approved from KRCL after getting third party certification).

17NS17 31590.00 Metre 1425.00 45015750.00 AT Par 45015750.00

Description:- Installation ,Testing and Commissioning of Stainless Steel SS 316 Cables Trays of size 200 mmx110mm /2mm thickness as per drawings.

18

NS18 8471.00 Set 5600.00 47437600.00 AT Par 47437600.00

Description:- Design & Supply of Universal Horizontal Coupler SS 316 (& conforming to specification detailed at 4A of SCC part - B) 04 Nos for each Horizontal bend (The design shall be got approved from KRCL after gettingthird party certification).

19NS19 8471.00 Set 458.00 3879718.00 AT Par 3879718.00

Description:- Installation universal Horizontal Coupler SS316 -04 Nos for ach Horizontal bends




20

NS20 7750.00 Set 6209.00 48119750.00 AT Par 48119750.00

Description:- Design & Supply of Universal Vertical Coupler SS 316 (& conforming to specification detailed at 4 Aof SCC part - B) 04 Nos for each Vertical bend (The design shall be got approved from KRCL after getting thirdparty certification).

21NS21 7750.00 Set 458.00 3549500.00 AT Par 3549500.00

Description:- Installation universal Vertical Coupler SS316 -04 Nos for Each Vertical bends

22

NS22 400.00 Metre 293.00 117200.00 AT Par 117200.00

Description:- Excavation of cable duct 150mm wide X 300mm deep for laying of cables in rocky area and refillingthe duct (after cable laying inside DWC/ GI pipe) with concrete mixture of proportion 1:3:6 and grouting the ends ateither side of the rocky portion using concrete mixture with contractor's own cement and other material.

23

NS23 653.00 Set 45248.00 29546944.00 AT Par 29546944.00

Description:- Earthing Items for Tunnels Supply, Installation, Testing & Commissioning of maintenance free earthfor Tunnel as per RDSO Specs. No RDSO/SPN/197/Ver. 1.0 1. Copper bonded steel electrode of 3.0 m long, 17.2mm dia with copper bonding thickness of minimum 250 microns and UL listed and marked = 1 no. 2. Earthenhancement material supplied in sealed bags of minimum 10 kg = 6 bags 3. Copper strip of 200 x 25 x 6mm(SEEB) = 1 no. 4. Copper strip of 150 x 25 x 6mm = 1 no.

24

NS24 3658.00 Numbers 1357.00 4963906.00 AT Par 4963906.00

Description:- Supply and Installation of Exothermic Joints: Exothermic Joint 200 x 25 x 6mm bus bar to 17.2mmRod (150gm) - Exothermic Joint of 35sqmm to 300 x 25 x 6mm bus bar (150gm)- Exothermic Joint 200 x 25 x6mm bus bar to 25 x 2mm Cu Strip (150gm) - Exothermic Joint 300 x 25 x 6mm bus bar to 25 x 2mm Cu Strip(150gm) - Exothermic Joint of 35sqmm to 150 x 25 x 6mm bus bar (150gm)- Exothermic Joint 300 x 25 x 6mmbus bar to 25 x 3mm Cu Strip (150gm) -

25NS25 112.00 Numbers 2149.00 240688.00 AT Par 240688.00

Description:- Supply and Installation of Copper strip of 300 x 25 x 6 mm (Test Link) = 2 no. (per niches)

26NS26 2829.00 Metre 1471.00 4161459.00 AT Par 4161459.00

Description:- Supply and Installation of 25 x 2 Cu Strip for interconnection of Earthing Rods in grid

27NS27 1301.00 Metre 430.00 559430.00 AT Par 559430.00

Description:- Supply and Installation of 35 Sqmm Wire for equipment connection

28NS28 2918.00 Per Unit 1103.00 3218554.00 AT Par 3218554.00

Description:- Earth Enhancement Material supplied in sealed bags of minimum 10Kg, for trenches(interconnection of earth pits) (PER UNIT=BAGS)

29NS29 18362.00 Metre 1273.00 23374826.00 AT Par 23374826.00

Description:- Supply and Installation of 25 x 3 Cu Strip for interconnection of niches and earthing grid on bothportal with throughout the tunnel

30NS30 172.00 Numbers 12443.00 2140196.00 AT Par 2140196.00

Description:- Supply and Installation of Isolation Spark Gap (For reduse the equipotential difference between twoearth pits)

38

NS38 2.00 Job 9087.00 18174.00 AT Par 18174.00

Description:- Fabrication of aluminium channel (1"x1") chamfered sunmica sheet on teakwood frame of size4'x2'x1" and supply thereof duly painted, yard diagram with stand on front and fixing the same in SMoffice/Cabins/R Hut diagram shall be painted as per SWR diagram by contractor. All materials to be supplied bycontractor.

39

NS39 8.00 Sqm 2069.00 16552.00 AT Par 16552.00

Description:- Supply, writing and fixing of description boards made of ply 6mm thick with white sunmica gluedover its surface and 1"x1" wooden baton fitted all around on the rear as per instruction of Engineer at site. All thematerials to be supplied by contractor.

40

NS40 2.00 Set 16039.00 32078.00 AT Par 32078.00

Description:- Installation ,wiring ,Testing and commissioning of 1024 Digital and 32 analogue inputs data loggercomplete along with accessories of Contractor's own wiring and fixing materials as per following configuration .(Itincludes loading of networking software and networking of datalogger the requisite communication cable /channelfor networking will be arranged by railways.

41

NS41 9.00 Per Unit 7409.00 66681.00 AT Par 66681.00

Description:- POINT MACHINE = Installation of KLCR & its box in location boxes, supply & installation of heavyduty push button, LED indicator on Bakelite sheet of 6 mm thickness inside location box for crank handle locking&releasing (with indication). The work includes fixing & wiring of magneto telephones, wiring of KLCR, push buttonsand termination of tail cables as per instructions of site Engineer. All material except KLCR relay & its box andmagneto telephone to be supplied by the contractor. This also includes fixing of wards on point machine.Foundation & installation of location box is covered as separate item of schedule. (PER UNIT= PERINSTALLATION)





Description:- Supply and Laying of Warning Tape for underground cables - 6 inch width, colour Red/Orange withwarning information painted in black (S&T cables).

43

NS43 50.00 KVA 1398.00 69900.00 AT Par 69900.00

Description:- Casting of vibration free foundation, installation of control panel, outlet for exhaust, laying of powercable from DG set to change over switch and wiring of DG set & control panel. Laying of cable/wires should becarried out in HDPE duct. This includes supply of all wiring, fixing & termination material of approved makerequired for above work (KVA= PER KVA)


Description:- Provision of Heat/Smoke Detection system


Description:- Supply, Manufacturing & installation of Integrated indication Panel

46

NS46 80.00 Kg 123.00 9840.00 AT Par 9840.00

Description:- Fabrication, Supply and fixing of various types of MS flat clamps on girder bridges/rocky area on GIpipes/its coupler as per drawing with requisite nos. of nut and bolts as per site requirements and as perinstructions of Railway Engineer at site.

47

NS47 10.00 Numbers 549.00 5490.00 AT Par 5490.00

Description:- Installation of desk type magneto telephone with all accessories including Standard battery box and3 nos. of 6 I cells. All materials for this installation including standard battery box and 6I cells will be supplied by thecontractor. Only desk type magneto telephone will be supplied by Railway (included as separate item of thisschedule).

48NS48 2.00 Set 56560.00 113120.00 AT Par 113120.00

Description:- Complete Installation and commissioning of Solar Panel system

51NS51 80.00 Numbers 2071.00 165680.00 AT Par 165680.00

Description:- Providing and fixing of M16x300mm anchor by drilling of hole with 20mm dia. bit with the depth of240mm & fixing the anchor with epoxy adhesive chemical for fixing of location boxes in the tunnels and bridges.

52NS52 10.00 Numbers 2285.00 22850.00 AT Par 22850.00

Description:- Providing and fixing of HAS M16 x 300mm anchor by drilling of hole with 20mm dia bit with thedepth of 240mm & fixing the anchor with epoxy adhesive chemical for fixing of shunt signal on tunnel wall / tunnel

53

NS53 20.00 Each 3184.00 63680.00 AT Par 63680.00

Description:- Providing Chemical anchoring on Concrete walls/ rock face using HAS M20 x 300 anchor bolts,including drilling hole of 25mm dia upto a depth of 170 mm, injecting suitable epoxy adhesive, curing etc complete.The work shall be dome with all Contractor's material, tools, labour, scaffolding etc complete (EACH= PERANCHOR BOLT)

54

NS54 40.00 Each 4754.00 190160.00 AT Par 190160.00

Description:- Providing Chemical anchoring on Concrete floor/ rock bed using HAS M 24 x 450 anchor bolts,including drilling hole of 25mm dia upto a depth of 350 mm, injecting suitable epoxy adhesive, curing etc complete.The work shall be dome with all Contractor's material, tools, labour, scaffolding etc complete Providing Chemicalanchoring on Concrete floor/ rock bed using HAS M 24 x 450 anchor bolts, including drilling hole of 25mm dia uptoa depth of 350 mm, injecting suitable epoxy adhesive, curing etc complete. The work shall be dome with allContractor's material, tools, labour, scaffolding etc complete Providing Chemical anchoring on Concrete floor/ rockbed using HAS M 24 x 450 anchor bolts, including drilling hole of 25mm dia upto a depth of 350 mm, injectingsuitable epoxy adhesive, curing etc complete. The work shall be dome with all Contractor's material, tools, labour,scaffolding etc complete Providing Chemical anchoring on Concrete floor/ rock bed using HAS M 24 x 450 anchorbolts, including drilling hole of 25mm dia upto a depth of 350 mm, injecting suitable epoxy adhesive, curing etccomplete. The work shall be dome with all Contractor's material, tools, labour, scaffolding etc complete EACH=peranchor bolt

55

NS55 10.00 Each 3942.00 39420.00 AT Par 39420.00

Description:- Providing Chemical anchoring on Concrete floor/ rock bed using HAS M 24 x 300 anchor bolts,including drilling hole of 25mm dia upto a depth of 125 mm, injecting suitable epoxy adhesive, curing etc complete.The work shall be dome with all Contractor's material, tools, labour, scaffolding etc complete (EACH=per anchorbolt)

56

NS56 10.00 Each 2407.00 24070.00 AT Par 24070.00

Description:- Providing Chemical anchoring on Concrete floor/ rock bed using HAS M 16 x 300 anchor bolts,including drilling hole of 25mm dia upto a depth of 240 mm, injecting suitable epoxy adhesive, curing etc complete.The work shall be dome with all Contractor's material, tools, labour, scaffolding etc complete (EACH=per anchorbolt)

57

NS57 2.00 Sqm 6810.00 13620.00 AT Par 13620.00




57Description:- Providing 12 mm thick washer plate of suitable size, including drilling required holes, filling of nonshrinkable cement grout between concrete/ rock surface and plate. The work shall be dome with all Contractor'smaterial, tools, labour, scaffolding etc complete

59NS59 4.00 Numbers 108940.00 435760.00 AT Par 435760.00

Description:- Supply of Special type location box to be fixed on tunnel wall as per drawing & instructions engineerincharge.

60

NS60 2.00 Numbers 73626.00 147252.00 AT Par 147252.00

Description:- Supply of Active lightning arrestor of Class 'A' for building protection as per standard NF C 17-102(of 2011). It shall work on Advanced Early Steamer Emission (ESE) principle and shall be made of Stainless Steelwith a T of 60 micro Sec or more. The system should be so designed to be capable of protecting against directlightning point as well as conducting/diverting it to Earth completely after tracing the lightning in advance. The airterminal should be of 1,000 mm length with 150 mm dia. (approx) and verified and tested from International lab formore than 100 kA current discharge. The system shall consist of: (i) Early Streamer Emission Air Terminal withfollowing features: • Stainless steel central capture head of 316L, also avoiding bolting and water infiltration thatcan cause premature corrosion. Test Certificate for protection against foreign solid substances and access todangerous parts and test of protection against water • Control over release of ions positive or negative Generationof streamer through corona effect • Level IV protection covering a radius 107 mtr. (approx.) • System should notdepend on electrical energy • ESE air terminal should be mounted on round DMC insulator having 50 to 80 mmdia and length of 145 mm (approx) for termination of down conductor. This should be mounted between airterminal and mast Note: Following test Certificates Shall be submitted at the time of supply (a) Advance triggeringtest time report (T of 60 micro or more) (b) Short circuit test report (100 kA or more), trigerring time @temperature (-) 40o C to (+) 120o C (c) 30 years Warranty Certificate from OEM (d) Internal last inspection reportof OEM shall be provided with every serial numbered lightning arrestor (ii) Supply of BLC Lighting Strike Counterwith following features: • Number of counts : 6 digits • Current sensitivity - 1 kA to 200 kA • Inductance shunt - 0.5micro Henry • Enclosure - IP 67 (iii) No external power source is required (iv) Provision shall be there to test thisdevice, if necessary, by an external tester. Generation of streamer through corona effect • Level IV protectioncovering a radius 107 mtr. (approx.) • System should not depend on electrical energy • ESE air terminal should bemounted on round DMC insulator having 50 to 80 mm dia and length of 145 mm (approx) for termination of downconductor. This should be mounted between air terminal and mast Note: Following test Certificates Shall besubmitted at the time of supply (a) Advance triggering test time report (T of 60 micro or more) (b) Short circuit testreport (100 kA or more), trigerring time @ temperature (-) 40o C to (+) 120o C (c) 30 years Warranty Certificatefrom OEM (d) Internal last inspection report of OEM shall be provided with every serial numbered lightningarrestor (ii) Supply of BLC Lighting Strike Counter with following features: • Number of counts : 6 digits • Currentsensitivity - 1 kA to 200 kA • Inductance shunt - 0.5 micro Henry • Enclosure - IP 67 (iii) No external power sourceis required (iv) Provision shall be there to test this device, if necessary, by an external tester.

61

NS61 2.00 Set 9067.00 18134.00 AT Par 18134.00

Description:- Supply of Mast (50 mm dia, GI) and support hardware (cantilevered/ guyed type, as required atsite) for suitable for mounting the ESE Lightning Arrester equipment for a height of 5 mtrs (above the roof, asrequired at site). All accessories like clamps, bracket, guy kit, cable ties, base plate, adapters, nut bolts etc shall besupplied by the Contractor.

62

NS62 100.00 Metre 499.00 49900.00 AT Par 49900.00

Description:- Supply of copper cable of size 70 sq mm insulated copper cable (black colour) for high lightningcurrent, as a down conductor. The tensile strength shall be between 220 - 270 N/ sqmm . The copper cable shallbe designed to take care of 200 kA discharge current.

63NS63 2.00 Set 2267.00 4534.00 AT Par 4534.00

Description:- Provision of Test Link Joints in IP 65 ABS Enclosure with transparent cover, Box size(180X180X138 mm), with all accessories complete. Copper test link size should be (150X25X3 mm)

64

NS64 4.00 Numbers 21761.00 87044.00 AT Par 87044.00

Description:- Supply of basic material to construct a Maintenance Free Ring Earth with Three Pits for achievingless than one Ohm Earth Resistance as per RDSO Spec No. RDSO/SPN/ 197/2008 (or with latest Amend)consisting of : a) Copper bonded steel electrodes of 3.0 m long, 17.2 mm dia with copper bonding thickness of min250 micron and UL listed and marked - 3 Nos. b) Earth Enhancement compound of approved brand supplied insealed bags of min 10 Kgs - 9 Nos. c) Copper strip of 300 x 25 x 6mm (MEEB) - 1 No. d) Copper strip of 150 x 25x 6mm (SEEB) - 2 Nos.

65NS65 50.00 Metre 408.00 20400.00 AT Par 20400.00

Description:- Supply of copper strip having cross section 25 x 3 mm for interconnecting the earth pits.

66NS66 200.00 Metre 272.00 54400.00 AT Par 54400.00

Description:- Supply of copper cable of size 35 sq mm Multi strand Single core PVC insulated as per IS 694 forconnecting to main earth electrode to MEEB in the equipment room.

67NS67 100.00 Metre 91.00 9100.00 AT Par 9100.00

Description:- Supply of copper cable of size 10 sq mm

NS68 2.00 Station 21945.00 43890.00 AT Par 43890.00




68

Description:- Supply & installation of PPTC (Polymetric Positive Temperature Coefficient) following fuses 100Numbers of each type for each Station. Sr. No.DescriptionVoltageH/CT/C 124V DC (10-12 Amps)30V9 Amp18Amp 6 Amp12 Amp 5 Amp10 Amp 224V DC (2-6 Amps)30V1.1 Amp2.2 Amp 1.6 Amp3.2 Amp 2.5 Amp5 Amp 3Amp6 Amp 4 Amp8 Amp 3110V AC (5-10 Amps)120V2 Amp4 Amp 1 Amp2 Amp 4110V DC (6-12 Amps)60V4Amp8 Amp 5 Amp10 Amp

69

NS69 3.00 Numbers 1425312.00 4275936.00 AT Par 4275936.00

Description:- Supply and installation of Integrated Service Router (ISR) as per RDSO draft specificationno.RDSO/SPN/TC/84/2008 or latest with 4 onboard GE, 3 NIM slots, 1 ISC slot, 3 SM slots, 8 GB Flash Memorydefault, 2 GB DRAM default (data plane), 4 GB DRAM default (control plane). The Integrated Services Routers(ISR) revolutionize WAN communications in the enterprise branch. With new levels of builtin intelligent networkcapabilities and convergence, the routers specifically address the growing need for application-aware networkingin distributed enterprise sites. These locations tend to have lean IT resources. But they often also have a growingneed for direct communication with both private data centers and public clouds across diverse links, includingMultiprotocol Label Switching (MPLS) VPNs and the Internet. Installation includes all Tool & Plant of Contractor(Make Cisco model ISR4461/K9 or similar)

3. ITEM BREAKUP

Schedule Schedule E-SCHEDULE-E ELECTRONIC INTERLOCKING

Item- 01

Design & Supply of Microprocessor based Electronic Interlocking system complete as per RDSO SpecificationRDSO/SPN/192/2005 with latest amendment to suit signalling plan. 110V AC is used for signal lamp lighting. Thesystem should have following composition (a) Hot standby designated as system A & System B (min) (b)Centralized EI With relay interface to drive field gears. (c) Dual VDU control terminals. VDU should be 42" drivenby industrial grade fanless PC (RDSO TAN STS/E/TAN/3007 dt 02.11.2012) as per clause 5.3 of RDSOSpecification no. RDSO/SPN/192/2005 or latest. (d) Power supply arrangement should be as per RDSO/TAN no.STS/E/TAN/3012 dt.28.08.2014. (e) Synchronization of EI clock and Data logger clock through CMU. (f) Relayrack (g) The communication equipment should include NMS, the specification and details should be submittedalong with the tender offer (h) Should have facility to get linked to Signal Control Centre (if required) (i) Shouldhave capability to interface with interlocked Level crossing gates in block section, IBS/IBH, Automatic BlockSignals and BPAC with object controllers on diversified OFC as per RDSO/TAN no. STS/E/TAN/3008. dt31.03.2013

S No. ItemNo

Description of Item Unit Qty Rate Amount

1 11 Basindadhar Station 1.00 13939670.00 13939670.00

2 12 Sangaldan Station 1.00 15584915.00 15584915.00

Total 29524585.00

Item- 02

Supply of essential Spares @ 10% of each cards/ module/PCBs for each EI system supplied under Item '1'subject to a minimum of one and any fractional quantity to be rounded off to next higher digit. The list of sparesrequired should be certified by OEM. Inspection by RDSO. For full description refer clause No2 technical specsfor schedule 'E'

S No. ItemNo



2 22 SANGALDHAN Station 1.00 2136437.00 2136437.00

Total 4272874.00

Item- 03

Installation, wiring, testing and commissioning of EI equipment & OC equipment supplied vide Schedule ItemNo.'1' including transportation from consignee's/ Contractor's Depot to site. This includes provision of non-deteriorating fuses, LED fuse blown indicators, termination of interface wires on the CT rack (FTOT) andpainting sleeve particulars. The input and output cables/wires (RDSO approved) used for interface wiring of EIshall be made of twisted pair. This work also includes: i.Provision of communication between Operator VDU andCIU using OFC cables laid in two separate path for each VDU duly supplying communication equipment.ii.Installation of EI Power supply equipment as per RDSO TAN No. STS/E/TAN/3012. iii.Synchronization of EIclock and Data logger clock through CMU. iv.Supply and provision of necessary Class A, B, C and D protectionas per RDSO guide lines and Railway practice. v. The contractor shall submit the OEM certificate for theinstallation as per RDSO prescribed format before commissioning of EI. [Non-deteriorating fuses, LED fuseblown indicators, indoor cable, wire coils, etc. required to wire the various relays and all other miscellaneousmaterials required for the work to be supplied by the contractor. Any other materials required for thecommissioning of EI shall be supplied by the contractor.] For full description refer clause No 3 of technical specsfor schedule 'E'

S No. ItemNo






2 32 Sangaldan Station 1.00 631250.00 631250.00

Total 1010000.00

Item- 08 Supply & installation of Automatic Fire detection & Suppression system for Relay Room (Size 7.1M x 4.6M x 3.5M Volume 115 m3) as per clause 8 of technical specs for schedule 'E'

S No. ItemNo


1 81 Supply of 80 Liter capacity Seamless Cylinder fitted withvalue assembly and along with mounting straps suitableto operate at 50 bar pressure complete with safety burstdisc, safety cap etc and with CCOE approval.

Numbers 2.00 154482.00 308964.00

2 82 Supply of non-toxic, environment friendly, non-corrosive,clean gaseous agent at the atmospheric pressure, safefor Electronic/ Electrical/ Telecommunication Equipment/Computers/,Human Friendly, non-residual, Noninflammable, type agent Heptafluropropane (C3F7H) gasGLCC USA make suitable for 700 Cu. meter Volume andsuitable for signaling relay. As per TechnicalSpecification

Kg 138.00 5288.00 729744.00

3 83 Supply of Microprocessor Based ProgrammableAddressable 4-Zone Controller suitable for both FireAlarm, Fire Suppression system and Electrical powerisolation. as per Technical Specification

Numbers 2.00 87502.00 175004.00

4 84 Supply of 50 Bar pressure/24 V DC Solenoid (Electrical)actuator assembly suitable to operate between 0 to 256seconds. As per Technical Specification

Numbers 2.00 55397.00 110794.00

5 85 Supply of Manual Actuator suitable for 50 bar operatingpressure. Suitable to manually having independent FMand UL approval. Made out of brass and suitable tointegrate with value assembly and solenoid value as pertechnical specification.

Numbers 2.00 10828.00 21656.00

6 86 Supply of Pneumatic actuator assembly suitable for 50bar operating pressure. Suitable pneumatically actuatehaving independent FM and UL approval. As perTechnical Spec.

Numbers 2.00 12716.00 25432.00

7 87 Supply of Brass Discharge Nozzle having independentUL/FM approvals. As per Technical Specification

Numbers 4.00 8813.00 35252.00

8 88 Supply of High Pressure Discharge hose suitable for thecylinder valve assembly having independent FM & ULapprovals. As per Technical Specification

Numbers 2.00 22411.00 44822.00

9 89 Supply of Manual Gas Release Unit. As per TechnicalSpecification

Numbers 2.00 5036.00 10072.00

10 810 Supply of Manual Gas Inhibit Unit. As per TechnicalSpecification

Numbers 2.00 5036.00 10072.00

11 811 Supply of M. S. Seamless Pipe as per ASTM 106 Gr. BPainted with 2 Coats of primer and 2 Cotes of RedEnamel Paint as per Design Requirement. (Note:Approximate 10 mtrs pipe will be supplied per cylinderalong with all accessories required like Bend, Tee,Coupler etc.)

Lot 2.00 57789.00 115578.00

12 812 Supply of Discharge Pressure Gauge. Numbers 2.00 16997.00 33994.00

13 813 Supply of Pressure Gurage to Monitor the Health ofCylinder suitable for 50 bar system having FM & ULapproval. A.s per the technical specification

Numbers 2.00 36008.00 72016.00

14 814 Supply of 140 Ltr. Cylinder strap. Numbers 4.00 2896.00 11584.00

15 815 Supply of Warning Sign/Instructions stickers and Boards. Numbers 2.00 2518.00 5036.00

16 816 Supply of Safety malfunction device Numbers 2.00 8561.00 17122.00

17 817 Supply of Reset Tool Numbers 2.00 7680.00 15360.00

18 818 Supply of Aspiration type Laser Based Smoke Sensorwith Internal Dual Air Filter. As per TechnicalSpecification

Numbers 2.00 239970.00 479940.00




19 819 Supply of U/V based flame sensor compatible withcontroller

Numbers 2.00 57663.00 115326.00

20 820 Supply of Power, Control and Data Cables for FireSuppression System.

Lot 2.00 313497.00 626994.00

21 821 UL Approved Digital Linear Heat Sensor Cable Metre 110.00 742.00 81620.00

22 822 Installation, Testing & Commissioning of completeAutomatic Fire Detection and Alarm System includingControl Panel, Flame sensor, Aspiration type smokeSensors, suppression types etc, (PER UNIT= PERROOM)

Per Unit 2.00 261248.00 522496.00

Total 3568878.00

Item- 09 Supply, installation, testing and commissioning of Fuse Fail Alarm system with automatic change over facility. asper Specifications at clause No 9 of technical specifications for schedule 'E'

S No. ItemNo


1 91 Supply of Fuse Auto Change over System (Type-I) withsupply voltage 110AC with alarm facility along with audiovisual indication as per RDSO Spec NoRDSO/SPN/209/2012 Rev-1.0 or Latest . One moduleshall cater 32 Nos of fuse from 0.6 to 4 Amps capacitiesin signalling circuits of 24 VDC, 60CDC & 110VDC.details of fuse voltage shall be supplied by site engineer -( 04 nos at each stn) (EACH = MODULE)

Each 8.00 39030.00 312240.00

2 92 Supply of common Audio visual alarm unit as per RDSOSpec NO RDSO/SPN/209/2012 Rev-1.0 or Latest (1unitper station)

Per Unit 2.00 5036.00 10072.00

3 93 GSM modem for connection to the system as per RDSOSpec NO RDSO/SPN/209/2012 Rev-1.0 or Latest (1unitper station)

Per Unit 2.00 19137.00 38274.00

4 94 Provision of wiring of common audio & visual alarm fromRelay Rack to SM's room on a separate panel withmuting facility

Set 2.00 3399.00 6798.00

5 95 Supply of 20 core PVC insulated indoor signalling multicore cable as per IRS specification 76/89 (latestAmendments of conductor 0.6 mm. Contractor shallprocure the cable through RDSO approved firms

Metre 1000.00 61.00 61000.00

6 96 Installation of wiring testing & commissioning of AutoFuse change over system along with common alarm &GMS modem per station

Set 2.00 5917.00 11834.00

Total 440218.00

Schedule Schedule D1-SCHEDULE-D1(NON SOR)

Item- 02 Indoor Signalling cable

S No. ItemNo


1 21 Supply of 60 core indoor signal cable as per IRS:S-76/89with amendement no-2 or latest conductor 0.6 mm size

Metre 600.00 166.00 99600.00

2 22 Supply of 40 core indoor signal cable as per IRS:S-76/89with amendement no-2 or latest conductor 0.6 mm size

Metre 600.00 113.00 67800.00

Total 167400.00

Item- 07 Supply of Spare cards for Single/Double line UFSBI as per RDSO/SPN/147/2005 with latest amendments), tosuit supply item no 38553 a & b in this schedule and for item at S.No 06

S No. ItemNo


1 71 Input Card Numbers 2.00 16579.00 33158.00

2 72 Output card Numbers 2.00 37048.00 74096.00

3 73 CPU Numbers 2.00 38145.00 76290.00

4 74 Control & Communication Card Numbers 2.00 32697.00 65394.00

5 75 Modem Numbers 2.00 37419.00 74838.00

6 76 DC-DC converter Card No.6 Numbers 2.00 58126.00 116252.00




7 77 Mother board Numbers 2.00 57063.00 114126.00

8 78 Reset Box Numbers 2.00 17256.00 34512.00

9 79 Flat Cable set Numbers 2.00 3270.00 6540.00

Total 595206.00

Item- 14 NS-14 Supply of Fuses of various capacity

S No. ItemNo


1 141 4 Amps Round Head HRC Fuse Numbers 200.00 63.00 12600.00




Total 41560.00

Item- 31 Supply of Cable Un-Screen PVC insulated armoured PVC sheathed for under ground usage of the followingsizes-

S No. ItemNo


1 311 Supply of 2 Core x 4 Sq.mm copper cable Kilometre 5.00 116796.00 583980.00

2 312 Suuply of 2C x 35 sqmm Aluminium Cable Kilometre 6.00 134673.00 808038.00

Total 1392018.00

Item- 73 Supply of spare cards for HA-SSDAC Axle counter to suit for supply item no 36107 in schedule A1

S No. ItemNo


1 731 Signal conditioner card No. (SCC1) for HASSDAC as perRDSO specification No. RDSO/SPN/177/2012 withversion 3 or latest

Numbers 1.00 45117.00 45117.00

2 732 Signal conditioner card No.2 (SCC2) for HASSDAC asper RDSO specification No .RDSO/SPN/177/2012 withversion 3 or latest

Numbers 1.00 45117.00 45117.00

3 733 Modem card No.3 for HASSDAC as per RDSOspecification No. RDSO/SPN/177/2012 with version 3 orlatest

Numbers 1.00 45117.00 45117.00

4 734 Dual Micro controller Logic card No.4 for HASSDAC Numbers 1.00 120913.00 120913.00

5 735 Relay Driver card No.5 Set 1.00 45117.00 45117.00

6 736 DC-DC converter Card No.6 Set 1.00 27070.00 27070.00

7 737 Reset box for HA-SSDAC as per RDSO No.RDSO/SPN/177/2012 with version 3 or latest

Numbers 1.00 64969.00 64969.00

8 738 Supply of Standard Tool kit for installation, Testing andMaintenance of Digital Axle Counter System.

Numbers 1.00 168804.00 168804.00

Total 562224.00

Schedule Schedule D2-SCHEDULE-D2 (NON SOR)

Item- 44 Provision of Heat/Smoke Detection system

S No. ItemNo


1 441 Supply, Installation & Commissioning of Smoke/HeatDetector and Fire alarm system (6 Smoke sensor atrelay room, 1 smoke sensor each at battery andequipment room/IPS room, 1 Sensor at OFC room and 1Heat sensor at DG room & OFC room) as per extantpractice of on Konkan Railway and as approved byEngineer in charge)

Station 2.00 238418.00 476836.00

2 442 Supply of smoke detector optical , applo make or similarfor fire alarm system

Numbers 30.00 5030.00 150900.00

3 443 Supply of Heat detector, applo make or similar for firealarm system

Numbers 10.00 5030.00 50300.00

Total 678036.00

Item- 45 Supply, Manufacturing & installation of Integrated indication Panel




S No. ItemNo


1 451 Arrangement of indication, Changeover distribution andCabling of the same with proper bracket as per the sitefor panel box as per attached drawing

Numbers 2.00 12433.00 24866.00

2 452 Fixing and installation of angle metal fram of 2", 100"H x88"L x 10"B as per attached drawing

Numbers 2.00 12763.00 25526.00

3 453 Metal frame finishing including 1' Metal border and CRCsheet 18 SWG with electrostatic epoxy power coated.

Numbers 2.00 13066.00 26132.00

Total 76524.00

4. ELIGIBILITY CONDITIONS

Important : All documents uploaded and remarks / confirmation entered by the bidders against any eligibility conditionshall be opened as part of technical bid only

Special Technical Criteria

S.No. Description ConfirmationRequired

RemarksAllowed

DocumentsUploading

1

The tenderer must have successfully completed any of the following during last 07(seven) years, ending last day of month previous to the one in which tender is invited:(a)Three similar works costing not less than the amount equal to 30% of advertisedvalue of the tender, OR (b)Two similar works costing not less than the amount equal to40% of advertised value of the tender, OR (c)One similar work costing not less than theamount equal to 60% of advertised value of the tender. Note: Work ExperienceCertificate from private individual shall not be considered. However, in addition to workexperience certificates issued by any Government organization, work experiencecertificate issued by Public listed company having average annual turnover of Rs. 500Crore and above in last three financial years excluding the current financial year listed onNational Stock Exchange or Bombay Stock Exchange incorporated / registered at least5 years prior to the date of opening of Tender shall also be considered provided the workexperience certificate has been issued by a person authorized by the public listedcompany to issue such certificate. In case tenderer submits work experience certificateissued by public listed company, the tenderer shall also submit along with workexperience certificate, the relevant copy of work order, bill of quantities, bill wise detailsof payment received duly certified by Chartered Accountant, TDS certificates for allpayments received and copy of final / last bill paid by company in support of above workexperience certificate. Similar work: Works shall be considered as similar if executedwork involves "Supply, Installation, Testing & Commissioning of EI/PI/RRI Works alongwith OFC / Quad Communication works".

No NoAllowed(Mandatory)

Special Financial Criteria


RemarksAllowed

DocumentsUploading

1

The tenderer must have received contractual payments in the previous three financialyears and the current financial year upto the date of inviting of tender, at least 150% ofthe advertised value of the tender. The tenderers shall submit Certificates to this effectwhich may be an attested Certificate from the concerned department / client and/orAudited Balance Sheet duly certified by the Chartered Accountant/Certificate fromChartered Accountant duly supported by Audited Balance Sheet. Note for 5.3: Clientcertificate from other than Govt Organization should be duly supported by Form16A/26AS generated through TRACES of Income Tax Department of India.

No No Allowed(Mandatory)

5. COMPLIANCE

Important : All documents uploaded and remarks / confirmation entered by the bidders against any compliancecondition shall be opened as part of technical bid only.

Commercial-Compliance


RemarksAllowed

DocumentsUploading

1Contract amount received in the pervious three finical year and the currentfinical year up to the date of opening of Tender: Appendix-5, should besubmitted along with supporting documents





2 Litigation History: Appendix-10 No NoAllowed(Mandatory)

3

Have you attached the Breakup of the rates quoted for item No.'1'of schedules'E'(separately for each station) as per Annexure E1 and uploaded theattachment against the 'upload only those which are required to be openedwith 2nd packet, i.e., Financial Bid' link/option available on Finical Offer page.

Yes Yes Not Allowed

4

Have you attached the Breakup of the rates quoted for item No.'2'of schedules'E'(separately for each station) as per Annexure E2 and uploaded theattachment against the 'upload only those which are required to be openedwith 2nd packet, i.e., Financial Bid' link/option available on Finical Offer page.

Yes Yes Not Allowed

5 Integrity Pact: Annexure-2 No NoAllowed(Mandatory)

6

Please enter the percentage of local content in the material being offered.Please enter 0 for fully imported items, and 100 for fully indigenous items. Thedefinition and calculation of local content shall be in accordance with the Makein India policy as incorporated in the tender conditions.

No YesAllowed(Optional)

Technical-Compliances


RemarksAllowed

DocumentsUploading

1

Statement of similar works executed during last 07 (seven) years, ending lastday of month previous to the one in which tender is invited: Appendix-2. Inaddition, required document as mentioned in clause 5.2 (Technical EligibilityCriteria) of Instruction To Tenderers


2

Statement of works in progress: The list of works in hand and in progressindicating the details as per Appendix-3, should be submitted duly Certified bya Chartered Accountants indicating 'B' Value as defined in clause 5.4.1 ofInstructions To Tenderers.


3 Statement of works abandoned/left Incomplete works: Appendix-4 No NoAllowed(Mandatory)

4 Tenderer's Information: Appendix-1 No NoAllowed(Mandatory)

5 List of available Personnel for key positions: Appendix-6A No NoAllowed(Mandatory)

6List of Personnel for key positions proposed to be deployed on this projectalong with CVs: Appendix-6B


7 Curriculum Vitae (CV) for Proposed Personnel for key positions: Appendix-6C No NoAllowed(Mandatory)

8 Compliance Certificate: Appendix-6D No NoAllowed(Mandatory)

9 Details of Plant & Machinery already available with the firm-Appendix-7A No NoAllowed(Mandatory)

10Details of Plant & Machinery proposed to be deployed for the work-Appendix-7B


11 List of equipment proposed to be deployed: Appendix-8 No NoAllowed(Mandatory)

12List of Laboratory equipment proposed to be installed/placed for the project:Appendix-9


13 Undertaking by Tenderer: Appendix-11 No NoAllowed(Mandatory)

14 Self Attested Certificate by Tenderer/ JV partners: Appendix-12. No NoAllowed(Mandatory)

15Details to be submitted by tenderer along with technical bid as part of theirmethod statement-Appendix-15


16 Certificate of Familiarization: Appendix - 17 No NoAllowed(Mandatory)

17Self Attested Certificate (Applicable for tender document downloaded fromIREPS website):Appendix - 20


18 Self Evaluation sheet: Appendix-21 No NoAllowed(Mandatory)




19

Self Attested Certificate for declaration of contracts rescinded/ terminated onaccount of poor performance in last 3 financial years immediately precedingthe current financial year and current financial year, upto date of opening oftender- Appendix-23.


20Undertaking regarding EI equipment (refer clause 5.6 of instruction toTenderers).


21Legal Document like Partnership deed, JV Agreement, Affidavits,Memorandum of Association, Resolution of BOD, power to Attorney, etcconcerned with the Tender.


6. Documents attached with tender

S.No. Document Name Document Description

1 GCC-July-2020.pdf Standard General Condition July2020

2Package3-Vol-I-15-09-2020_Part1_1.pdf

Tender Doc Vol I Part 1

















11 Package-3-Vol-II-15-09-2020_1.pdf Tender Doc Vol II

12 SIP-Basindadhar_1.pdf SIP OF BASINDADHAR

13 SIP-Sangaldan_1.pdf SIP OF SANGALDAN

This tender complies with Public Procurement Policy (Make in India) Order 2017, dated 15/06/2017, issued byDepartment of Industrial Promotion and Policy, Ministry of Commerce, circulated vide Railway Board letter no.2015/RS(G)/779/5 dated 03/08/2017 and 27/12/2017.

Signed By: SACHIN BALAKRISHNA KADU

Designation : ASTE/P/USBRL


