LUXAFLOOR® FCF is a two pack, high performance, fast cure floor coating designed to get assets back into service quickly with very short cure times while maintaining a long pot life allowing for flexible application.

LUXAFLOOR® FCF exhibits excellent gloss and colour retention under UV exposure, making it suitable for exterior application.

LUXAFLOOR® FCF should be applied on to correctly prepared concrete floors with LUXAFLOOR® AGGREGATES for slip resistant finishes as required.

Please refer to Luxafloor® FCF data sheet for more information. Results of laboratory testing when the aggregate is applied as per directions and usage rates in the Luxafloor® aggregate data sheet.

Luxafloor FCF®

MEETING SLIP RESISTANCE SPECIFICATIONS

FAST CURE FLOOR COATING

AggregateWet PendulumAS 4586: 2013

Oil-Wet RampAS 4586: 2013

No Aggregate P1 R9

Luxafloor® Stir In Aggregate Fine P3 R10

Luxafloor® Stir in Aggregate Coarse P3 R10

Luxafloor® Broadcast Aggregate No 36

P5 R12

FEATURES BENEFITS

Isocyanate free

8 hour pot life Flexibility in application time

2 hour recoat Job done in a day

Fast curing 1 day full cure

CO

NC

RET

E FL

OO

R P

RO

TEC

TIO

N

NEW CONCRETE

01Remove all surface contaminants with Gamlen CA 1 detergent.

02Fill any cracks or voids using appropriate repair filler*.

03Diamond grind, track or light shot blast. Remove all dust by vacuum cleaning.

*IF USING REPAIR FILLERS OR YOU ARE IN ANYDOUBT ABOUT POTENTIAL CONTAMINANTS INTHE CONCRETE, PRIME WITH DUREMAX® GPE WITHQUICKTURN™ HARDENER AS THE FIRST COAT PRIORTO USING LUXAFLOOR® FCF.

CONCRETE WITH EXISTING COATING

01Test adhesion by standard cross hatch adhesion test. If coating fails remove it. If coating is sound continue.

02Remove all surface contaminants with Gamlen CA 1 detergent.

03Fill any cracks or voids using appropriate repair filler. Spot prime any bare areas.

04 Diamond grind. Vacuum clean to remove all dust.

LUXAFLOOR® FCF WILL NOT CURE ON ALKYD BASED OR WATER BASED FLOOR COATINGS. IF YOU ARE IN ANY DOUBT ABOUT THE EXISITING COATING TYPE USE DUREMAX® GPE WITH QUICKTURN™ HARDENER AS THE FIRST COAT PRIOR TO USING LUXAFLOOR® FCF.

PREPARATION

APPLICATION TO RETURN TO SERVICE - possible in 2 days*

MEETING SLIP RESISTANCE SPECIFICATIONS

» DO NOT use Luxafloor® FCF over concrete that has been prepared by acid etch

» DO NOT pour Luxafloor® FCF into concrete expansion gaps

» DO NOT tint Luxafloor® FCF – contact a Dulux® PC representative for advice

» Luxafloor® FCF is not compatible with repair fillers – use a primer.

If you're in any doubt about contaminants, use Duremax® GPE with Quickturn™ Hardener as a primer.

Luxafloor® FCF can be applied directly to concrete with the following precautions:

*Comparison at 25°C and 50% relative humidity. Total service time will vary.Application time has been calculated at 2 hours. Timeline is based on continuous work.

START

2 5 7 13

FIRSTCoat

SECONDCoat

3HOURSRECOAT

L ight Traffic

Light Traffic

2 DAYS

9 DAYS

START

HOW MANY HOURS?

HOW MANY HOURS? 31

14HOURSRECOAT

2 16 18 42

186

FIRSTCoat

SECONDCoat

Return to Service

Return to Service

1st coat: Duremax® GPE with Quickturn™ Hardener 2nd coat: Luxafloor® FCF

Standard Epoxy Floor Coating With Standard Hardener

Any advice, recommendation, information, assistance or service provided by DULUX Australia in relation to goods manufactured by it or their use and application is given in good faith and is believed by Dulux to be appropriate and reliable. However, any advice, recommendation, information, assistance or service provided by Dulux is provided without liability or responsibility PROVIDED THAT the foregoing shall not exclude, limit, restrict or modify the right entitlements and remedies conferred upon any person or the liabilities imposed upon Dulux by any condition or warranty implied by Commonwealth, State or Territory Act or ordinance void or prohibiting such exclusion limitation or modification. Products can be expected to perform as indicated on the products datasheet so long as applications and application procedures are as recommended.

APPLICATION TO RETURN TO SERVICE - possible in 2 days*

START

2 5 7 13

FIRSTCoat

SECONDCoat

3HOURSRECOAT

L ight Traffic

Light Traffic

2 DAYS

9 DAYS

START

HOW MANY HOURS?

HOW MANY HOURS? 31

14HOURSRECOAT

2 16 18 42

186

FIRSTCoat

SECONDCoat

Return to Service

Return to Service

1st coat: Duremax® GPE with Quickturn™ Hardener 2nd coat: Luxafloor® FCF

Standard Epoxy Floor Coating With Standard Hardener

Dulux Australia1956 Dandenong RoadClayton VIC 3168

Dulux Customer ServicePhone 13 23 77

Dulux New Zealand150 Hutt Park RoadLower Hutt New Zealand

Dulux NZ Customer ServicePhone 0800 800 424

For more detailed product and safety information orfor your nearest store location please visit our website.

www.duluxprotectivecoatings.com.au® Dulux, the Squares Device, Luxafloor and Duremax are registered trade marks of DuluxGroup (Australia) Pty Ltd.TM Quickturn is a trade mark of DuluxGroup (Australia) Pty Ltd.

SCAN ME