1

Head Office Factory

ISO Certificate

Products

Quality assurance

Prototypes must pass Parts and materials

LocationOur head office is located on Taksin road in Bangkok metropolis while our factory is in Nakornpathom which is 30 km to the west. The factory comprises machine shop, fabrication areas, electrical shop, paint shop, design office, test area, finished product warehouse, show rooms, training room and factory administration office, covering a total area of over 2000 square meters.

Services

llation commissioning

Development of new products is based on market requirements as well as trend in educational innovation and technological development. Most of our equipments are available for inspection and/or test run in our factory show room. Popular items are normally deliverable from stock. In addition, we also build special equipment for research and other purposes to meet client special requirement as well as providing assistance in planning new laboratory.All products are supplied with completed operating manuals. Software with software manual are also available as optional items.

ESSOM has been certified ISO 9001 Quality Management System since 1999. The scope of certification includes Design and Manufacturing of engineering equipment as well as Sales and Service of both engineering education and paint spray equipment. All our engineering education products have been designed by our experienced and well qualified engineers. design test standards before market introduction. are sourced from approved supplier/material lists and must pass receipt inspection. In-process inspection is carried out at key manufacturing stages with final inspection after completion. All new products must pass strike design test before market introduction.

We maintain over 20 well trained engineers and scientists and a number of experienced technicians readily available to provide services such as equipment set up, instaand operation.

Introduction

ESSOM was founded in 1986 by a group of engineers. Our main objective was to market DeVilbiss paint spray equipment. A few years later the company began to manufacture engineering education equipment. Over the years, paint spray equipment from Binks,Ransburg and Nihon Parkerizer were added. At the same time, engineering education equipment has grown from import substitute to worldwide export.

Market

With our global marketing network of agents and sales partners we have now supplied our equipments to over 50 countries.

We are committed to strive towards excellence and to make ESSOM aworldwide recognized brand name in the field of technical education.

Dear Customers,

Welcome to ESSOM 2017 brief catalog. Here products are arranged in sub-groups for quick reference. A relatively new product group – Mechanical Engineering Test Sets (MM500) are expanded and overlap with other Theory of Machine (MM) and Structures (ST) products. Also Structures (ST) products are now modified to include computer assist sets. New products are added in Thermodynamics (TH), particularly in heat exchangers and refrigeration.

With the ISO 9001:2015 Quality Management System, we are committed to the Continuous Improvement policy particularly on product design and appearance as well as instruction manual improvement to be among the world leaders in this field of engineering education. We appreciate your continued suggestions and supports to help us serve you better.

Please visit our website www.essom.com for more information.

Thank you

(Naris Srinilta)

Managing Director

SHOW ROOM

DESIGN TEST / FINAL TEST

HB012 HYDROSTATIC PRESSURE TRAINING

for University of Sargodha, Pakistan

TH136 COMPACT STEAM TURBINE POWER PLANT TRAINING for Mapua University,

Philippines.

HF530 FLOW CHANNEL TRAINING for Capital University of Science and Technology and COSMOS, Pakistan.

MP315D SUBSONIC WIND TUNNEL TRAINING for Akademi Teknik Dan

Keselamatan Penerbangan, Indonesia

HT210 PELTON TURBINE TEST SET TRAINING for The Nelson Mandela African Institution of Science and

Technology, Tanzania.

2

ABOUT ESSOM

Head Office Factory

ISO Certificate

Products

Quality assurance

Prototypes must pass Parts and materials

LocationOur head office is located on Taksin road in Bangkok metropolis while our factory is in Nakornpathom which is 30 km to the west. The factory comprises machine shop, fabrication areas, electrical shop, paint shop, design office, test area, finished product warehouse, show rooms, training room and factory administration office, covering a total area of over 2000 square meters.

Services

llation commissioning

Development of new products is based on market requirements as well as trend in educational innovation and technological development. Most of our equipments are available for inspection and/or test run in our factory show room. Popular items are normally deliverable from stock. In addition, we also build special equipment for research and other purposes to meet client special requirement as well as providing assistance in planning new laboratory.All products are supplied with completed operating manuals. Software with software manual are also available as optional items.

ESSOM has been certified ISO 9001 Quality Management System since 1999. The scope of certification includes Design and Manufacturing of engineering equipment as well as Sales and Service of both engineering education and paint spray equipment. All our engineering education products have been designed by our experienced and well qualified engineers. design test standards before market introduction. are sourced from approved supplier/material lists and must pass receipt inspection. In-process inspection is carried out at key manufacturing stages with final inspection after completion. All new products must pass strike design test before market introduction.

We maintain over 20 well trained engineers and scientists and a number of experienced technicians readily available to provide services such as equipment set up, instaand operation.

Introduction

ESSOM was founded in 1986 by a group of engineers. Our main objective was to market DeVilbiss paint spray equipment. A few years later the company began to manufacture engineering education equipment. Over the years, paint spray equipment from Binks,Ransburg and Nihon Parkerizer were added. At the same time, engineering education equipment has grown from import substitute to worldwide export.

Market

With our global marketing network of agents and sales partners we have now supplied our equipments to over 50 countries.

We are committed to strive towards excellence and to make ESSOM aworldwide recognized brand name in the field of technical education.

Dear Customers,

Welcome to ESSOM 2017 brief catalog. Here products are arranged in sub-groups for quick reference. A relatively new product group – Mechanical Engineering Test Sets (MM500) are expanded and overlap with other Theory of Machine (MM) and Structures (ST) products. Also Structures (ST) products are now modified to include computer assist sets. New products are added in Thermodynamics (TH), particularly in heat exchangers and refrigeration.

With the ISO 9001:2015 Quality Management System, we are committed to the Continuous Improvement policy particularly on product design and appearance as well as instruction manual improvement to be among the world leaders in this field of engineering education. We appreciate your continued suggestions and supports to help us serve you better.

Please visit our website www.essom.com for more information.

Thank you

(Naris Srinilta)

Managing Director

SHOW ROOM

DESIGN TEST / FINAL TEST

HB012 HYDROSTATIC PRESSURE TRAINING

for University of Sargodha, Pakistan

TH136 COMPACT STEAM TURBINE POWER PLANT TRAINING for Mapua University,

Philippines.

HF530 FLOW CHANNEL TRAINING for Capital University of Science and Technology and COSMOS, Pakistan.

MP315D SUBSONIC WIND TUNNEL TRAINING for Akademi Teknik Dan

Keselamatan Penerbangan, Indonesia

HT210 PELTON TURBINE TEST SET TRAINING for The Nelson Mandela African Institution of Science and

Technology, Tanzania.

3

MOVING FORWARD

The steam power plant trainer acquired by the Mapua University is instrumental in conveying engineering knowledge and skills to our engineering students. Modern instrumentation and controls as well as data processing were also integrated to its system. experiments prescribed by our ME program are covered by the equipment specifications and would require less effort to modify the system to adopt to other requirement. therefore, the equipment enhances our capability to do research and provide a real life experience to our students.

With this regard, we are greatly satisfied with the qualityand as well the after sales service of the manufacturer.

UNISA has purchased all its Thermodynamics equipment from ESSOM, and herewith we would like to express our satisfaction with the products.

The equipment is effective; experiments are repeatable with a high degree of accuracy and a great deal more value for money.

We have commissioned some of the equipment and are now in the process on commissioning the Steam Power Plant. The Boiler is working well.

I am pleased with the progress made so far. I hope we will have a good working relationship, throughout the considerable long life-span of this equipment.

I have been using the essom laboratory equipment since 2011 and found these up to my full satisfaction. The significant parameter is the value of money. The equipment is cost effective and don’t compromise the quality at any level. Quality sensors are used for precise measurements in all of equipment while rugged and durable parts increase the effective life of equipment. Another advantage is the possibilities of equipment to be tailored as per specific requirements/ situations. Their aftersales service and response to queries is exceptionally surpassing, at least, in our region of the world. I am satisfied with the products I have used so far.

Dr. Engr. Muhammad Atiq Ur Rehman TariqAssociate ProfessorDepartment of Civil EngineeringCapital University of Science and Technology,Islamabad, Pakistan

The advice I am giving always to all my engineering students and colleagues is above all to study the lab apparatuses overwhelmingly the state-of-the-art ESSOM lab apparatuses for instructional purposes and students utilisation are quantum leaps upward. I am confident that ESSOM will not only be soon at par with the world-wide giant manufacturers in this arena but will have leapfrog products for science and engineering research as well.”

Prof Dr Imtiaz HakeemBSc Mech Eng(UET, Peshawar, Pakistan) PhD; DIC (Imperial College, London)Department of Mechanical EngineeringSarhad University of Science & ITPeshawar, KPK, Pakistan

T. SithebeLecturerDepartment of Mechanical &Industrial EngineeringUniversity of South Africa (UNISA)

Engr Roel John C Judilla,PME, ASEAN EngProfessor, Mapua UniversityPhilippines

MAPUA UNIVERSITY

UNIVERSITY OF SOUTH AFRICA (UNISA)

THAI-NISHI INSTITUTE OF TECHNOLOGY

HB : HYDRAULICS BENCH AND ACCESSORIES

HF : FLOW MEASUREMENT AND FLOW STUDY

HP : PUMP TEST SET

Page

6

9

12

HT : TURBINE TEST SET

MP : AIR FLOW AND AIR COMPRESSION

RE : RENEWABLE ENERGY

MT & TH : THERMODYNAMICS

BP & HM : CHEMICAL ENGINEERING AND FOOD TECHNOLOGY

TM : STRENGTH AND PROPERTY OF MATERIALS

MM : MACHINE ELEMENTS AND THEORY OF MACHINES

ST : STRUCTURES AND ACCESSORIES

For further details, please visit our website www.essom.com

13

15

16

17

24

22

23

27

4

TESTIMONIALS

The steam power plant trainer acquired by the Mapua University is instrumental in conveying engineering knowledge and skills to our engineering students. Modern instrumentation and controls as well as data processing were also integrated to its system. experiments prescribed by our ME program are covered by the equipment specifications and would require less effort to modify the system to adopt to other requirement. therefore, the equipment enhances our capability to do research and provide a real life experience to our students.

With this regard, we are greatly satisfied with the qualityand as well the after sales service of the manufacturer.

UNISA has purchased all its Thermodynamics equipment from ESSOM, and herewith we would like to express our satisfaction with the products.

The equipment is effective; experiments are repeatable with a high degree of accuracy and a great deal more value for money.

We have commissioned some of the equipment and are now in the process on commissioning the Steam Power Plant. The Boiler is working well.

I am pleased with the progress made so far. I hope we will have a good working relationship, throughout the considerable long life-span of this equipment.

I have been using the essom laboratory equipment since 2011 and found these up to my full satisfaction. The significant parameter is the value of money. The equipment is cost effective and don’t compromise the quality at any level. Quality sensors are used for precise measurements in all of equipment while rugged and durable parts increase the effective life of equipment. Another advantage is the possibilities of equipment to be tailored as per specific requirements/ situations. Their aftersales service and response to queries is exceptionally surpassing, at least, in our region of the world. I am satisfied with the products I have used so far.

Dr. Engr. Muhammad Atiq Ur Rehman TariqAssociate ProfessorDepartment of Civil EngineeringCapital University of Science and Technology,Islamabad, Pakistan

The advice I am giving always to all my engineering students and colleagues is above all to study the lab apparatuses overwhelmingly the state-of-the-art ESSOM lab apparatuses for instructional purposes and students utilisation are quantum leaps upward. I am confident that ESSOM will not only be soon at par with the world-wide giant manufacturers in this arena but will have leapfrog products for science and engineering research as well.”

Prof Dr Imtiaz HakeemBSc Mech Eng(UET, Peshawar, Pakistan) PhD; DIC (Imperial College, London)Department of Mechanical EngineeringSarhad University of Science & ITPeshawar, KPK, Pakistan

T. SithebeLecturerDepartment of Mechanical &Industrial EngineeringUniversity of South Africa (UNISA)

Engr Roel John C Judilla,PME, ASEAN EngProfessor, Mapua UniversityPhilippines

MAPUA UNIVERSITY

UNIVERSITY OF SOUTH AFRICA (UNISA)

THAI-NISHI INSTITUTE OF TECHNOLOGY

HB : HYDRAULICS BENCH AND ACCESSORIES

HF : FLOW MEASUREMENT AND FLOW STUDY

HP : PUMP TEST SET

Page

6

9

12

HT : TURBINE TEST SET

MP : AIR FLOW AND AIR COMPRESSION

RE : RENEWABLE ENERGY

MT & TH : THERMODYNAMICS

BP & HM : CHEMICAL ENGINEERING AND FOOD TECHNOLOGY

TM : STRENGTH AND PROPERTY OF MATERIALS

MM : MACHINE ELEMENTS AND THEORY OF MACHINES

ST : STRUCTURES AND ACCESSORIES

For further details, please visit our website www.essom.com

13

15

16

17

24

22

23

27

5

CONTENTS

HB 019 ORIFICE AND JET FLOW Orifice diameter plates, trajectory probes, adjustable head tank. Optional: Bottom discharge with traverse mechanism

The Hydraulics Bench is a primary unit to provide water supply and flow measurement for various experiments on fluid properties. Each experiment requires specific accessory. Learning software is available for most experiments .

BASIC UNITS

FLOW IN PIPE AND ANOTHER FLOW ACCESSORIES

HB 101 BASIC HYDRAULIC BENCH A simple bench for supply and measurement of volume flow rate. A 0. 37 kW pump with water meter and storage tank.

HB 100G HYDRAULIC BENCH, Gravimetric For water supply and measurement of weight rate of flow. A 0. 37 kW Pump with 45 kg measuring tank, weights and storage tank.

HB 100 HYDRAULICS BENCH For water supply and measurement of volume flow rate. A 0.37 kW pump with 10 and 45 lt measuring tank and storage tank

HB 018 BENDS AND FITTINGS FRICTION

Test pipe with enlarged section. Fittings:

90° miter bend, 90°°elbow, 90 small radius bend, 90° large radius bend, 45° elbows, sudden expansion and contraction. Water manometer.

HB 016P PITOT TUBE APPARATUS The tube is used for a study of velocity distribution across a pipe section and measurement of flow velocity.

HB 017 PIPE FRICTION Adjustable head 800-1000 mm, storage tank, water manometer, differential pressure measuring device, test section over 500 mm long, vertical or horizontal pipe.

HB 016 FLOW METERS Variable area flow meter, Venturi tube, orifice plate, Pitot tube water manometers.

HB 015 BERNOULLI’S THEOREM APPARATUS Venturi tube diameters 28 and 14 mm, total head probe and manometers.

HB 022 FREE AND FORCED VORTEX, Rotating Paddle

Transparent tank, with over flow. 4 orifices of different diameters, and rotating paddle. Profile probes, Pitot tube.

HB 022A FREE AND FORCED VORTEX, Rotating Tank

Transparent tank with concentric perforated cylinder. Drive motor with speed control, cross bar with depth probe and Pitot tube.

HB 013 FLOW OVER A NOTCH Rectangular notch, 60° and 90° V-notches.

150 mm stainless steel vernier hook and point gauge.

HB 020 IMPACT OF A JET A nozzle diameter 7 mm, with target plates: flat, 120° cone, 180° hemisphere, 120° outward. Transparent tank and setof weight.

HB 101-013 FLOW OVER A NOTCH CHANNEL

For use in testing a flow over a notch on HB 100G Hydraulics Bench, gravimetric and HB 101 Basic Hydraulics Bench.

HB 021 FLOW THROUGH AN ORIFICE

Standard sharp edge orifice and traversemechanism screw with Pitot tube, variablehead and transparent tank.Optional: Additional different orifices

PUMP AND TURBINE TEST ACCESSORIES

HB 041 CAVITATION PANEL Transparent Venturi tube with pressure gauges. For use with Hydraulics Bench or outside water supply.

HB 026 LAMINAR FLOW APPARATUS Channel size 260 mm wide x 360 mm long, source/sink holes, dye reservoir with stream lines, various rubber models.

HB 027 MINI FLOW CHANNEL Channel and dye reservoir with stream line needles. Models: small and large cylinder, narrow crested, broad crested weir, crump weir, symmetrical and asymmetrical aerofoil.

HB 030M SERIES AND PARALLEL PUMPS, Multi Speeds

Two multi speed centrifugal pumps connected together with pipings and valves for series and parallel operation.

HB 030F SERIES AND PARALLEL PUMPS, Fixed Speed

A fixed speed centrifugal pump is connected with pipings to a Hydraulics Bench for the study of two pumps in series or parallel operation.

HB 023A MINI AXIAL FLOW PROPELLER TURBINE

Metal guide vanes and runner. Transparent window and runner section. Mechanical brake with spring balances, low range pressure gauge and hand tachometer.

Output: Over 10 W

HB 023F MINI FRANCIS TURBINE Metal runner, non-corrosion metal housing and transparent window. Mechanical brake with spring balances, pressure gauge and hand tachometer. Output: over 25 W

HB 023K MINI KAPLAN TURBINE Metal runner, non-corrosion metal housing and transparent window and runner section. Mechanical brake with spring balances, pressure gauge and hand tachometer. Output: Over 15 W

HB 024 OSBORNE REYNOLDS

APPARATUS Vertical test pipe with bell mouth, pipe length over 700 mm, stilling tank, dye reservoir with a needle.

HB 023AI MINI AXIAL FLOW IMPULSE TURBINE

Metal runner and housing. Transparent discharge window. Mechanical brake with spring balances, pressure gauge and hand tachometer. Output: Over 25 W

HB 024H OSBORNE REYNOLDS

APPARATUS, Horizontal Test Pipe

Horizontal test pipe diameter with bell mouth, pipe length over 700 mm, transparent test pipe shell with stilling baffle, dye reservoir with a needle.

HB 023P MINI PELTON TURBINE Stainless steel runner and nozzle and housing with transparent window.

Mechanical brake with spring balances, pressure gauge and hand tachometer.

Output: Over 40 W .

HB 025 HYDRAULIC RAM PUMP Demonstration of the effect of hydraulic ram where a large supply of flowing water at lower head is made to deliver a small amount of water at a higher head.

HB 029 CENTRIFUGAL PUMP, Variable Speed

A 0.37 kW pump and motor with advanced inverter with speed and input power indication, pressure gauges.

HB 029R RECIPROCATING PUMP Small reciprocating pump with motor, pressure relief valve, pulse chamber and pressure gauges.

6

HYDRAULICS BENCH AND ACCESSORIES

HB 019 ORIFICE AND JET FLOW Orifice diameter plates, trajectory probes, adjustable head tank. Optional: Bottom discharge with traverse mechanism

The Hydraulics Bench is a primary unit to provide water supply and flow measurement for various experiments on fluid properties. Each experiment requires specific accessory. Learning software is available for most experiments .

BASIC UNITS

FLOW IN PIPE AND ANOTHER FLOW ACCESSORIES

HB 101 BASIC HYDRAULIC BENCH A simple bench for supply and measurement of volume flow rate. A 0. 37 kW pump with water meter and storage tank.

HB 100G HYDRAULIC BENCH, Gravimetric For water supply and measurement of weight rate of flow. A 0. 37 kW Pump with 45 kg measuring tank, weights and storage tank.

HB 100 HYDRAULICS BENCH For water supply and measurement of volume flow rate. A 0.37 kW pump with 10 and 45 lt measuring tank and storage tank

HB 018 BENDS AND FITTINGS FRICTION

Test pipe with enlarged section. Fittings:

90° miter bend, 90°°elbow, 90 small radius bend, 90° large radius bend, 45° elbows, sudden expansion and contraction. Water manometer.

HB 016P PITOT TUBE APPARATUS The tube is used for a study of velocity distribution across a pipe section and measurement of flow velocity.

HB 017 PIPE FRICTION Adjustable head 800-1000 mm, storage tank, water manometer, differential pressure measuring device, test section over 500 mm long, vertical or horizontal pipe.

HB 016 FLOW METERS Variable area flow meter, Venturi tube, orifice plate, Pitot tube water manometers.

HB 015 BERNOULLI’S THEOREM APPARATUS Venturi tube diameters 28 and 14 mm, total head probe and manometers.

HB 022 FREE AND FORCED VORTEX, Rotating Paddle

Transparent tank, with over flow. 4 orifices of different diameters, and rotating paddle. Profile probes, Pitot tube.

HB 022A FREE AND FORCED VORTEX, Rotating Tank

Transparent tank with concentric perforated cylinder. Drive motor with speed control, cross bar with depth probe and Pitot tube.

HB 013 FLOW OVER A NOTCH Rectangular notch, 60° and 90° V-notches.

150 mm stainless steel vernier hook and point gauge.

HB 020 IMPACT OF A JET A nozzle diameter 7 mm, with target plates: flat, 120° cone, 180° hemisphere, 120° outward. Transparent tank and setof weight.

HB 101-013 FLOW OVER A NOTCH CHANNEL

For use in testing a flow over a notch on HB 100G Hydraulics Bench, gravimetric and HB 101 Basic Hydraulics Bench.

HB 021 FLOW THROUGH AN ORIFICE

Standard sharp edge orifice and traversemechanism screw with Pitot tube, variablehead and transparent tank.Optional: Additional different orifices

PUMP AND TURBINE TEST ACCESSORIES

HB 041 CAVITATION PANEL Transparent Venturi tube with pressure gauges. For use with Hydraulics Bench or outside water supply.

HB 026 LAMINAR FLOW APPARATUS Channel size 260 mm wide x 360 mm long, source/sink holes, dye reservoir with stream lines, various rubber models.

HB 027 MINI FLOW CHANNEL Channel and dye reservoir with stream line needles. Models: small and large cylinder, narrow crested, broad crested weir, crump weir, symmetrical and asymmetrical aerofoil.

HB 030M SERIES AND PARALLEL PUMPS, Multi Speeds

Two multi speed centrifugal pumps connected together with pipings and valves for series and parallel operation.

HB 030F SERIES AND PARALLEL PUMPS, Fixed Speed

A fixed speed centrifugal pump is connected with pipings to a Hydraulics Bench for the study of two pumps in series or parallel operation.

HB 023A MINI AXIAL FLOW PROPELLER TURBINE

Metal guide vanes and runner. Transparent window and runner section. Mechanical brake with spring balances, low range pressure gauge and hand tachometer.

Output: Over 10 W

HB 023F MINI FRANCIS TURBINE Metal runner, non-corrosion metal housing and transparent window. Mechanical brake with spring balances, pressure gauge and hand tachometer. Output: over 25 W

HB 023K MINI KAPLAN TURBINE Metal runner, non-corrosion metal housing and transparent window and runner section. Mechanical brake with spring balances, pressure gauge and hand tachometer. Output: Over 15 W

HB 024 OSBORNE REYNOLDS

APPARATUS Vertical test pipe with bell mouth, pipe length over 700 mm, stilling tank, dye reservoir with a needle.

HB 023AI MINI AXIAL FLOW IMPULSE TURBINE

Metal runner and housing. Transparent discharge window. Mechanical brake with spring balances, pressure gauge and hand tachometer. Output: Over 25 W

HB 024H OSBORNE REYNOLDS

APPARATUS, Horizontal Test Pipe

Horizontal test pipe diameter with bell mouth, pipe length over 700 mm, transparent test pipe shell with stilling baffle, dye reservoir with a needle.

HB 023P MINI PELTON TURBINE Stainless steel runner and nozzle and housing with transparent window.

Mechanical brake with spring balances, pressure gauge and hand tachometer.

Output: Over 40 W .

HB 025 HYDRAULIC RAM PUMP Demonstration of the effect of hydraulic ram where a large supply of flowing water at lower head is made to deliver a small amount of water at a higher head.

HB 029 CENTRIFUGAL PUMP, Variable Speed

A 0.37 kW pump and motor with advanced inverter with speed and input power indication, pressure gauges.

HB 029R RECIPROCATING PUMP Small reciprocating pump with motor, pressure relief valve, pulse chamber and pressure gauges.

7

HYDRAULICS BENCH AND ACCESSORIES

HYDROSTATIC TEST ACCESSORIES AND EQUIPMENT

HB 210 PRESSURE MEASUREMENT APPARATUS

This apparatus is for studying and understanding the basic pressure measuring devices using manometers, pressure gauges. Vacuum gauge, Dead weight pressure tester.

HB 201 HYDROSTATICS PANEL A bench top panel with equipment for calibration, determination, measurement and demonstration of properties/behavior of fluid under static condition. Over 15 experiments.

HB 200 HYDROSTATICS BENCH A self-contained bench with equipment for calibration, determination, measurement and demonstration of various properties or behavior of fluids under static conditions.

Over 18 experiments.

HB 205 FLUID STATICS AND MANOMETRY

A bench top apparatus for providing knowledge and measurement of liquid under hydrostatic conditions using manometers

SP 111 ARCHIMEDES PRINCIPLE APPARATUS

A solid metal and a hollow clear acrylic cylinder, a spring balance, a beaker and a stand.

SP 112 PASCAL’S APPARATUS Four different glass vessels, vessel holder with pressure balancing beam, a load hanger, weights and a stand.

SP 113 BOYLE’S LAW APPARATUS An acrylic tube on stand with scale, a pressure gauge, a pressure relief valve and control valves.

PH 100 MANOMETERS Water, inclined water, and mercury manometers for both water and air pressure measurements. Various ranges are available.

HB 011 DEAD WEIGHT PRESSURE TESTER

A piston with known piston cross-section, calibrated weights and pressure gauge.

HB 014 METACENTRIC HEIGHT For a study of stability of a floating body.

400 mm long x 200 mm wide x 100 mm high pontoon. Graduated mast height and tilt angle.

HB 012 HYDROSTATIC PRESSURES Quadrant inner radius 100 mm, outer radius 200 mm and width 75 mm. Balance arm with counter weight and weights.

Transparent tank.

HB 012B HYDROSTATIC PRESSURE, Tilting Jar Quadrant

Transparent quadrant inside inner radius 100 mm, inside outer radius 200 mm, inside width 75 mm. Tilting upto 30 degrees in either direction. Balance arm with counter weight and weights.

HB 012A HYDROSTATIC PRESSURE, Tilting Submerged Quadrant

Quadrant inner radius 100 mm, outer radius 200 mm and width 75 mm. Tilting up to 30 degrees in either direction. Balance arm with counter weight and weights.

Transparent tank

HF 111 PARTICLE DRAG COEFFICIENTS

Two glass tube columns 100 mm diameter x 1. 5 m long with top guide, bottom valves and back fluorescent lamp.

Ball spheres of different materials, shapes and diameters, stop watch.

HF 501 SEDIMENT BED AND FLOW VISUALIZATION TANK Large working section with sand bed. Head tank, storage tank with sand trap and adjustable overshot weir, circulating pump, ripples measuring devices, sand and various accessories.

PIPING LOSS TEST SETS Several models of equipment for study of loss in straight pipes, bends, fittings and valves are available: HF 125 and HF 125A. In addition,

primary flow measuring devices are added for models HF 135 and HF 135A.

SEDIMENTATION AND HYDROLOGY

HF 135 PIPING LOSS TEST SET, Large A self-contained set for measuring losses with primary flow measuring devices, differential pressure measuring devices, pumpand storage tank.HF 125 PIPING LOSS TEST SET, Small Similar to HF135 with only measuring losses.

HF 135A PIPING LOSS APPARATUS, Large A panel type for measuring losses with primary flow measuring devices and differential pressure measuring devices for use with a Hydraulics Bench or outside water supply. HF 125A PIPING LOSS APPARATUS, Small Similar to HF135A with only measuring losses.

HF 171 CAVITATION TEST SET A self-contained unit. Transparent Venturi tube, pressure gauges, pump and variable area flow meter.

HF 160 WATER HAMMER APPARATUS Two pipes, one with manual closing valve for pipe surge study and the other with quick closing valve, pressure sensors, signal converter and software for data display on computer for water hammer study. The set is for use with Hydraulics Bench.

HF 235 FLOW MEASUREMENT TEST SET A self-contained set with Venturi meter, orifice meter, Pitot tube, variable area flow meter, water meter, measuring tank and manometers.

Storage tank and pump.

HF 150 PIPE NETWORK APPARATUS A set of pipes and manifolds for studying flow in pipes under various network configuration with differential pressure

measuring

measuring devices and Hydraulics Bench.

8

HYDRAULICS BENCH AND ACCESSORIES

MISCELLANEOUS

HYDROSTATIC TEST ACCESSORIES AND EQUIPMENT

HB 210 PRESSURE MEASUREMENT APPARATUS

This apparatus is for studying and understanding the basic pressure measuring devices using manometers, pressure gauges. Vacuum gauge, Dead weight pressure tester.

HB 201 HYDROSTATICS PANEL A bench top panel with equipment for calibration, determination, measurement and demonstration of properties/behavior of fluid under static condition. Over 15 experiments.

HB 200 HYDROSTATICS BENCH A self-contained bench with equipment for calibration, determination, measurement and demonstration of various properties or behavior of fluids under static conditions.

Over 18 experiments.

HB 205 FLUID STATICS AND MANOMETRY

A bench top apparatus for providing knowledge and measurement of liquid under hydrostatic conditions using manometers

SP 111 ARCHIMEDES PRINCIPLE APPARATUS

A solid metal and a hollow clear acrylic cylinder, a spring balance, a beaker and a stand.

SP 112 PASCAL’S APPARATUS Four different glass vessels, vessel holder with pressure balancing beam, a load hanger, weights and a stand.

SP 113 BOYLE’S LAW APPARATUS An acrylic tube on stand with scale, a pressure gauge, a pressure relief valve and control valves.

PH 100 MANOMETERS Water, inclined water, and mercury manometers for both water and air pressure measurements. Various ranges are available.

HB 011 DEAD WEIGHT PRESSURE TESTER

A piston with known piston cross-section, calibrated weights and pressure gauge.

HB 014 METACENTRIC HEIGHT For a study of stability of a floating body.

400 mm long x 200 mm wide x 100 mm high pontoon. Graduated mast height and tilt angle.

HB 012 HYDROSTATIC PRESSURES Quadrant inner radius 100 mm, outer radius 200 mm and width 75 mm. Balance arm with counter weight and weights.

Transparent tank.

HB 012B HYDROSTATIC PRESSURE, Tilting Jar Quadrant

Transparent quadrant inside inner radius 100 mm, inside outer radius 200 mm, inside width 75 mm. Tilting upto 30 degrees in either direction. Balance arm with counter weight and weights.

HB 012A HYDROSTATIC PRESSURE, Tilting Submerged Quadrant

Quadrant inner radius 100 mm, outer radius 200 mm and width 75 mm. Tilting up to 30 degrees in either direction. Balance arm with counter weight and weights.

Transparent tank

HF 111 PARTICLE DRAG COEFFICIENTS

Two glass tube columns 100 mm diameter x 1. 5 m long with top guide, bottom valves and back fluorescent lamp.

Ball spheres of different materials, shapes and diameters, stop watch.

HF 501 SEDIMENT BED AND FLOW VISUALIZATION TANK Large working section with sand bed. Head tank, storage tank with sand trap and adjustable overshot weir, circulating pump, ripples measuring devices, sand and various accessories.

PIPING LOSS TEST SETS Several models of equipment for study of loss in straight pipes, bends, fittings and valves are available: HF 125 and HF 125A. In addition,

primary flow measuring devices are added for models HF 135 and HF 135A.

SEDIMENTATION AND HYDROLOGY

HF 135 PIPING LOSS TEST SET, Large A self-contained set for measuring losses with primary flow measuring devices, differential pressure measuring devices, pumpand storage tank.HF 125 PIPING LOSS TEST SET, Small Similar to HF135 with only measuring losses.

HF 135A PIPING LOSS APPARATUS, Large A panel type for measuring losses with primary flow measuring devices and differential pressure measuring devices for use with a Hydraulics Bench or outside water supply. HF 125A PIPING LOSS APPARATUS, Small Similar to HF135A with only measuring losses.

HF 171 CAVITATION TEST SET A self-contained unit. Transparent Venturi tube, pressure gauges, pump and variable area flow meter.

HF 160 WATER HAMMER APPARATUS Two pipes, one with manual closing valve for pipe surge study and the other with quick closing valve, pressure sensors, signal converter and software for data display on computer for water hammer study. The set is for use with Hydraulics Bench.

HF 235 FLOW MEASUREMENT TEST SET A self-contained set with Venturi meter, orifice meter, Pitot tube, variable area flow meter, water meter, measuring tank and manometers.

Storage tank and pump.

HF 150 PIPE NETWORK APPARATUS A set of pipes and manifolds for studying flow in pipes under various network configuration with differential pressure

measuring

measuring devices and Hydraulics Bench.

9

FLOW MEASUREMENT AND FLOW STUDY EQUIPMENT

HF 502 SEDIMENT FLOW CHANNEL Bench top channel 7.5 cm wide x 15 cm high x 150 cm long, 0 to +10% tilting with pump, feed tank, storage tank,accessories and sand.

TILTING FLOW CHANNEL

Several sizes of flow channels are available as per standard below other test section and length are available on requested. Accessories are installed on the channel for study on various flow phenomena. The flow channel is supplied with necessary system e.g. water circulating, tilting, flow measurement. Computer control is available as an option.

SMALL SIZE●

●

MEDIUM SIZE

HF 510 TILTING FLOW CHANNEL Size: 10 cm wide x 30 cm high x 400 cm long and -2% to + 5% tilting. HF 515 TILTING FLOW CHANNEL Size: 15 cm wide x 35 cm high x 600 or 800 cm long and -1 % to + 3 % tilting.

HF 311 GROUND WATER FLOW APPARATUS A tank with two inlet pipes and two outlet wells.

Manometers, sand and models.

HF 315 PERMEABILITY APPARATUS Stainless steel tank with glass front, pressure tapping points and manometers, over flow pipes, complete with pump, tank, dye injection, end baffles, sand and models.

HF 505 TILTING FLOW CHANNEL Bench top channel. Size: 5 cm wide x 15 cm high x 200 cm long and -2 to +5% tilting. Adjustable bed is an optional. HF 508 TILTING FLOW CHANNEL Bench top channel Size: 7.5 cm wide x 25 cm high x 250 cm long and -2 to +5% tilting. HF 507 TILTING FLOW CHANNEL Size; 7.5 cm. wide x 25 cm. high x 300 cm. long and –2 to + 5% tilting.

HF 401 BASIC HYDROLOGY APPARATUSA stainless steel tank with tilting mechanism.

Side compartments, wells and sprinkler nozzles. Complete with storage tank, pump, flow meter and calibrated weir and sand.

HF 510A TILTING FLOW CHANNEL, Adjustable bed Size: 10 cm wide x 30 cm high x 400 cm long and -2% to + 5% tilting. HF 515A TILTING FLOW CHANNEL, Adjustable bed Size: 15 cm wide x 35 cm high x 600 or 800 cm long and -1 % to + 3 % tilting.

LARG• E SIZE

ACCESSORIES FOR TILTING FLOW CHANNEL Accessories and models shown below are for large Tilting Flow Channel models HF 530 and HF 560. Slightly different designs are also

available for smaller flow channels eg HF 515, HF 510, HF 507and HF 505.

OPEN CHANNEL AND CLOSED CHANNEL FLOW

HF 530 TILTING FLOW CHANNEL Size: 30 cm wide x 45 cm high x 6 to 12.5 m long and -1% to +3% tilting.

HF 509 OPEN CHANNEL AND CLOSED CHANNEL FLOW Size: 7.5 cm × 15 cm high × 120cm long.Flow channel with removable lid to simulate open and closed channel. Adjustable bed and optional accessories.

Parshall Flume Vibration Pile Venturi Flume

Pitot Tube

Bridge Pier

Culvert Fittings

Trapezoidal Flume

Syphon Spillway

Sluice Gate

Current Meter

Submerged Orifice Lift and Drag Balance and Models

Wave Generator Absorbing Beaches

Hook and Point Gauge

Dam Spillway Weirs

Radial Gate

Ogee Weir with Manometer Board

Roughened Beds

HF 560 TILTING FLOW CHANNEL Size: 60 cm wide x 70 cm high x 18 m long and -0.5 to +2% tilting.

10

FLOW MEASUREMENT AND FLOW STUDY EQUIPMENT

HF 502 SEDIMENT FLOW CHANNEL Bench top channel 7.5 cm wide x 15 cm high x 150 cm long, 0 to +10% tilting with pump, feed tank, storage tank,accessories and sand.

TILTING FLOW CHANNEL

Several sizes of flow channels are available as per standard below other test section and length are available on requested. Accessories are installed on the channel for study on various flow phenomena. The flow channel is supplied with necessary system e.g. water circulating, tilting, flow measurement. Computer control is available as an option.

SMALL SIZE●

●

MEDIUM SIZE

HF 510 TILTING FLOW CHANNEL Size: 10 cm wide x 30 cm high x 400 cm long and -2% to + 5% tilting. HF 515 TILTING FLOW CHANNEL Size: 15 cm wide x 35 cm high x 600 or 800 cm long and -1 % to + 3 % tilting.

HF 311 GROUND WATER FLOW APPARATUS A tank with two inlet pipes and two outlet wells.

Manometers, sand and models.

HF 315 PERMEABILITY APPARATUS Stainless steel tank with glass front, pressure tapping points and manometers, over flow pipes, complete with pump, tank, dye injection, end baffles, sand and models.

HF 505 TILTING FLOW CHANNEL Bench top channel. Size: 5 cm wide x 15 cm high x 200 cm long and -2 to +5% tilting. Adjustable bed is an optional. HF 508 TILTING FLOW CHANNEL Bench top channel Size: 7.5 cm wide x 25 cm high x 250 cm long and -2 to +5% tilting. HF 507 TILTING FLOW CHANNEL Size; 7.5 cm. wide x 25 cm. high x 300 cm. long and –2 to + 5% tilting.

HF 401 BASIC HYDROLOGY APPARATUSA stainless steel tank with tilting mechanism.

Side compartments, wells and sprinkler nozzles. Complete with storage tank, pump, flow meter and calibrated weir and sand.

HF 510A TILTING FLOW CHANNEL, Adjustable bed Size: 10 cm wide x 30 cm high x 400 cm long and -2% to + 5% tilting. HF 515A TILTING FLOW CHANNEL, Adjustable bed Size: 15 cm wide x 35 cm high x 600 or 800 cm long and -1 % to + 3 % tilting.

LARG• E SIZE

ACCESSORIES FOR TILTING FLOW CHANNEL Accessories and models shown below are for large Tilting Flow Channel models HF 530 and HF 560. Slightly different designs are also

available for smaller flow channels eg HF 515, HF 510, HF 507and HF 505.

OPEN CHANNEL AND CLOSED CHANNEL FLOW

HF 530 TILTING FLOW CHANNEL Size: 30 cm wide x 45 cm high x 6 to 12.5 m long and -1% to +3% tilting.

HF 509 OPEN CHANNEL AND CLOSED CHANNEL FLOW Size: 7.5 cm × 15 cm high × 120cm long.Flow channel with removable lid to simulate open and closed channel. Adjustable bed and optional accessories.

Parshall Flume Vibration Pile Venturi Flume

Pitot Tube

Bridge Pier

Culvert Fittings

Trapezoidal Flume

Syphon Spillway

Sluice Gate

Current Meter

Submerged Orifice Lift and Drag Balance and Models

Wave Generator Absorbing Beaches

Hook and Point Gauge

Dam Spillway Weirs

Radial Gate

Ogee Weir with Manometer Board

Roughened Beds

HF 560 TILTING FLOW CHANNEL Size: 60 cm wide x 70 cm high x 18 m long and -0.5 to +2% tilting.

11

FLOW MEASUREMENT AND FLOW STUDY EQUIPMENT

Several Pump Test Sets are available for fixed speed, multi speed and variable speed control. Measuring instruments may be analog or digital

and a computer interface is provided for either data display, analysis or computer control operation.

PUMP DEMONSTRATION UNIT, Computer Interface

PUMP TEST SET

HP 309V SERIES AND PARALLEL PUMP TEST SET, Variable Speed

HP 111 CENTRIFUGAL PUMP DEMONSTRATION UNIT, Computer Interface

HP 119V CENTRIFUGAL PUMP TEST SET, Variable Speed

Optional: Computer interface

HP 301 SERIES AND PARALLEL PUMPS DEMONSTRATION UNIT, Computer Interface

Optional: Computer interface

HP 104 ADVANCED INVERTER WITH COMPUTER INTERFACE UNIT

The unit consists of an advanced inverter for controlling and indicating motor speed and power, digital display with computer interface unit for sensors. To be used for HP111, HP121, HP131, HP141 and HP301.

HP 141 RECIPROCATING PUMP DEMONSTRATION UNIT, Computer Interface

MODEL NAME DESCRIPTION HP 111 CENTRIFUGAL PUMP

A bench top unit with 0.37 kW pump and motor, storage tank, sensors and software.

HP 121 TURBINE PUMP HP 131 GEAR PUMP HP 141 RECIPROCATING PUMP HP 301 SERIES AND PARALLEL PUMPS

NAME MODEL OF SMALL PUMP TEST SET Fixed Speed Variable Speed Multi Speed

SIZE: 0.37 kW SIZE: 0.24 kW

COMPACT CENTRIFUGAL PUMP

HP 115

HP 115V

HP 115M COMPACT TURBINE PUMP HP 125 HP 125V COMPACT GEAR PUMP HP 135 HP 135V COMPACT RECIPROCATING PUMP HP 145 HP145V COMPACT SERIES AND PARALLEL PUMP HP 305V HP 305M

SIZE: 1.1 – 1.5 kW CENTRIFUGAL PUMP HP 119V SERIES AND PARALLEL PUMP HP 309V

PUMP TEST SET WITH TRUE PUMP INPUT, Motor Dynamometer (0.55 kW)

We generally offer 3 sizes of turbine. The mini units for 0.37 to 0.55 kW pump, compact units for 2.2 kW pump and large units for 7.5 kW pump.

MINI TURBINE DEMONSTRATION UNIT, Computer Interface

Each turbine unit supplied with speed and torque sensors. It is designed to be used with HT110 Mini Turbine Service unit. Several types of turbines can be alternatively placed on a common water supply with central and measuring instruments.

HP 305V COMPACT SERIES AND PARALLEL PUMP TEST SET, Variable speed

HP 305M COMPACT SERIES AND PARALLEL PUMP TEST SET, Multi Speed

HP 113 COMPACT CENTRIFUGAL PUMP TEST SET, Motor Dynamometer

HP 303 COMPACT SERIES AND PARALLEL PUMP TEST SET, Motor Dynamometer

HP 405 MULTI PUMP TEST SET, Motor Dynamometer Similar to HP405B with motor dynamometer.

Stainless steel runner, nozzle and housing with transparent window. Maximum output: Over 40 W.

Metal runner, adjustable guide vanes non-corrosion metal housing with transparent window. Maximum output: Over 25 W.

HP 405B COMPACT MULTI PUMP TEST SET, Inverter Speed Control

A bench top unit for centrifugal, turbine, reciprocating and axial flow pumps, each with 0. 55 kW motor.

Common control unit for inverter and selector switch, storage tank and measuring instruments.

HT 110 MINI TURBINE SERVICE UNIT A bench top unit with 0.37 kW pump and storage tank for providing water supply to the mini turbine demonstration unit.

Pressure and flow sensors, interface box, power supply. This is to be used with HT121, HT131, HT151AI and HT161.

HT 151A MINI AXIAL FLOW PROPELER TURBINE DEMONSTRATION UNIT, Computer Interface

Metal runner with transparent casing guide vane andrunner section. 0.55 kW pump and storage tank.Speed, pressure, flow and torque sensors. Maximumoutput: Over 15W.

.

HT 151AI MINI AXIAL FLOW IMPULSE TURBINE DEMONSTRATION UNIT, Computer Interface

HT 161 MINI KAPLAN TURBINE DEMONSTRATION UNIT,

Computer Interface

HT 121 MINI PELTON TURBINE DEMONSTRATION UNIT, Computer Interface

HT 131 MINI FRANCIS TURBINE DEMONSTRATION UNIT, Computer Interface

Metal runner and casing with transparent window. Maximum output: Over 25 W.

Stainless steel runner, adjustable guide vanes non-corrosion metal casing with transparent window and runner section. Maximum output: Over 15 W.

12

PUMP TEST SETS

Several Pump Test Sets are available for fixed speed, multi speed and variable speed control. Measuring instruments may be analog or digital

and a computer interface is provided for either data display, analysis or computer control operation.

PUMP DEMONSTRATION UNIT, Computer Interface

PUMP TEST SET

HP 309V SERIES AND PARALLEL PUMP TEST SET, Variable Speed

HP 111 CENTRIFUGAL PUMP DEMONSTRATION UNIT, Computer Interface

HP 119V CENTRIFUGAL PUMP TEST SET, Variable Speed

Optional: Computer interface

HP 301 SERIES AND PARALLEL PUMPS DEMONSTRATION UNIT, Computer Interface

Optional: Computer interface

HP 104 ADVANCED INVERTER WITH COMPUTER INTERFACE UNIT

The unit consists of an advanced inverter for controlling and indicating motor speed and power, digital display with computer interface unit for sensors. To be used for HP111, HP121, HP131, HP141 and HP301.

HP 141 RECIPROCATING PUMP DEMONSTRATION UNIT, Computer Interface

MODEL NAME DESCRIPTION HP 111 CENTRIFUGAL PUMP

A bench top unit with 0.37 kW pump and motor, storage tank, sensors and software.

HP 121 TURBINE PUMP HP 131 GEAR PUMP HP 141 RECIPROCATING PUMP HP 301 SERIES AND PARALLEL PUMPS

NAME MODEL OF SMALL PUMP TEST SET Fixed Speed Variable Speed Multi Speed

SIZE: 0.37 kW SIZE: 0.24 kW

COMPACT CENTRIFUGAL PUMP

HP 115

HP 115V

HP 115M COMPACT TURBINE PUMP HP 125 HP 125V COMPACT GEAR PUMP HP 135 HP 135V COMPACT RECIPROCATING PUMP HP 145 HP145V COMPACT SERIES AND PARALLEL PUMP HP 305V HP 305M

SIZE: 1.1 – 1.5 kW CENTRIFUGAL PUMP HP 119V SERIES AND PARALLEL PUMP HP 309V

PUMP TEST SET WITH TRUE PUMP INPUT, Motor Dynamometer (0.55 kW)

We generally offer 3 sizes of turbine. The mini units for 0.37 to 0.55 kW pump, compact units for 2.2 kW pump and large units for 7.5 kW pump.

MINI TURBINE DEMONSTRATION UNIT, Computer Interface

Each turbine unit supplied with speed and torque sensors. It is designed to be used with HT110 Mini Turbine Service unit. Several types of turbines can be alternatively placed on a common water supply with central and measuring instruments.

HP 305V COMPACT SERIES AND PARALLEL PUMP TEST SET, Variable speed

HP 305M COMPACT SERIES AND PARALLEL PUMP TEST SET, Multi Speed

HP 113 COMPACT CENTRIFUGAL PUMP TEST SET, Motor Dynamometer

HP 303 COMPACT SERIES AND PARALLEL PUMP TEST SET, Motor Dynamometer

HP 405 MULTI PUMP TEST SET, Motor Dynamometer Similar to HP405B with motor dynamometer.

Stainless steel runner, nozzle and housing with transparent window. Maximum output: Over 40 W.

Metal runner, adjustable guide vanes non-corrosion metal housing with transparent window. Maximum output: Over 25 W.

HP 405B COMPACT MULTI PUMP TEST SET, Inverter Speed Control

A bench top unit for centrifugal, turbine, reciprocating and axial flow pumps, each with 0. 55 kW motor.

Common control unit for inverter and selector switch, storage tank and measuring instruments.

HT 110 MINI TURBINE SERVICE UNIT A bench top unit with 0.37 kW pump and storage tank for providing water supply to the mini turbine demonstration unit.

Pressure and flow sensors, interface box, power supply. This is to be used with HT121, HT131, HT151AI and HT161.

HT 151A MINI AXIAL FLOW PROPELER TURBINE DEMONSTRATION UNIT, Computer Interface

Metal runner with transparent casing guide vane andrunner section. 0.55 kW pump and storage tank.Speed, pressure, flow and torque sensors. Maximumoutput: Over 15W.

.

HT 151AI MINI AXIAL FLOW IMPULSE TURBINE DEMONSTRATION UNIT, Computer Interface

HT 161 MINI KAPLAN TURBINE DEMONSTRATION UNIT,

Computer Interface

HT 121 MINI PELTON TURBINE DEMONSTRATION UNIT, Computer Interface

HT 131 MINI FRANCIS TURBINE DEMONSTRATION UNIT, Computer Interface

Metal runner and casing with transparent window. Maximum output: Over 25 W.

Stainless steel runner, adjustable guide vanes non-corrosion metal casing with transparent window and runner section. Maximum output: Over 15 W.

13

PUMP TEST SETS

TURBINE TEST SETS

MINI TURBINE TEST SETS These sets are self-contained. Each mini turbine test set supplied with 0.37 – 0.55 kW pump, storage tank and measuring instruments.

COMPACT TURBINE TEST SETS These are self -contained medium set turbines with 2.2 kW pump, storage tank and measuring instruments. Computer interface is an optional.

HT 701 MINI PELTON / FRANCIS TURBINE TEST SET

Pelton turbine with stainless steel runner, nozzle and metal housing with transparent window. Francis turbine with Metal runner, adjustable guide vanes and casing with transparent window. Maximum output: 25-40 W.

HT 201 MINI PELTON TURBINE TEST SET

Stainless steel runner, and nozzle.

Non-corrosion metal housing and transparent window. Maximum output: Over 40 W.

HT 501A MINI AXIAL FLOW PROPELLER TURBINE TEST SET

Maximum output: Over 15 W.

HT 501AI MINI AXIAL FLOW IMPULSE TURBINE TEST SET

Maximum output: Over 25 W.

HT 601 MINI KAPLAN TURBINE TEST SET

Maximum power: Over 15 W.

HT 301 MINI FRANCIS TURBINE TEST SET

Maximum output: Over 25 W.

HT 203 COMPACT PELTON TURBINE TEST SET

Maximum output: 450 W.

HT 303 COMPACT FRANCIS TURBINE TEST SET Bronze runner, adjustable guide vanes and casing with transparent window. Maximum output: 400 W.

HT 403 COMPACT CROSS FLOW TURBINE TEST SET

Maximum output: 400 W.

HT 603 COMPACT KAPLAN TURBINE TEST SET

Maximum output: 400 W.

HT 702 COMPACT PELTON / FRANCIS TURBINE TEST SET

Pelton turbine with stainless steel runner, nozzle and casing with transparent window. Francis turbine with bronze runner, adjustable guide vanes and casing with transparent window. Maximum output: 400 - 450 W.

HT 703 MULTI TURBINE TEST SET Stainless steel runner Pelton turbine, bronze runner. Francis turbine, stainless steel runner cross-flow turbine and stainless steel runner Kaplan turbine. Maximum output: 400-450 W.

LARGE TURBINE TEST SETSThese are large turbine test set with 7.5 kW pump,storage tank and measuring instruments.

Direct coupling electric generator.

HT 210 PELTON TURBINE TEST SETStainless steel runner. Stainless steel nozzle and casing with transparent window.

Maximum output:2000 W .

HT 410CROSSFLOW TURBINE TEST SETHT 610KAPLAN TURBINE TEST SET

HT 310 FRANCIS TURBINE TEST SET HT 210 PELTON TURBINE TEST SET

This equipment is designed to the study of air flow measurement performance of fan, blower and compressor as well as related flow

behavior. DEMONSTRATION UNIT, Computer Interface

FAN AND BLOWER (SMALL AND LARGE SIZE)

WIND TUNNELS

MP 111 MULTI STAGE CENTRIFUGAL AIR COMPRESSOR DEMONSTRATION UNIT, Computer Interface

A bench top unit with 1 kW two stage compressor, inlet orifice, outlet damper, sensors and software. To be used with computer.

MP 121 AXIAL FLOW FAN DEMONSTRATION UNIT, Computer Interface

A bench top unit with 24 W axial flow fan and motor, inlet orifice, outlet damper, flow straighteners, sensors and software. To be used with computer.

MP 110 CENTRIFUGAL FAN DEMONSTRATION UNIT,

Computer Interface A bench top unit with centrifugal fan, 0.75 kW motor, inlet orifice, outlet damper; sensors and software. To be used with computer.

MP 100 AIR FLOW BENCH A centrifugal fan with 0.55 kW motor, inlet pipe, outlet pipe with damper, flow straighteners, orifice plate, nozzle, inlet cone, travelling pitot, inclined and multi tube manometers and optional items.

MP 124 AXIAL FLOW FAN TEST SET Axial flow fan with 2.2 kW motor and an advanced inverter, flow straightener, guide vane, outlet damper, measuring instruments and other optional items.

MP 142 FLOW VISUALIZATION WIND TUNNEL This is a unit for visualization of air flow stream lines around models. It consists of a stilling entrance, a viewing window, models, a smoke generator and distributor and a small blower.

MP 115 COMPACT CENTRIFUGAL FAN TEST SET

Bench top unit with centrifugal fan, 0.75 kW motor, advanced inverter, inlet orifice, outlet damper, inclined manometer, hand tachometer, thermometer and barometer.

MP 125 COMPACT AXIAL FLOW FAN TEST SET Bench top unit with 24 W axial flow fan and motor, inlet orifice, outlet damper, speed indicator, inclined manometer, ammeter, voltmeter, thermometer and barometer.

MP 119 CENTRIFUGAL BLOWER TEST SET A centrifugal blower and 2.2 kW motor with an advanced inverter, outlet amper, flow straighteners,

orifice plate, Venturi nozzle, inclined manometers

MP 315D SUBSONIC WIND TUNNEL, Downstream Fan An axial flow with 0.75 kW variable speed motor, 150 mm x 150 mm test section, maximum air speed over 30 m/sec, two component balance, various accessories and models. Optional: Computer interface and computer control.

and measuring instruments.

14

TURBINE TEST SETS

MINI TURBINE TEST SETS These sets are self-contained. Each mini turbine test set supplied with 0.37 – 0.55 kW pump, storage tank and measuring instruments.

COMPACT TURBINE TEST SETS These are self -contained medium set turbines with 2.2 kW pump, storage tank and measuring instruments. Computer interface is an optional.

HT 701 MINI PELTON / FRANCIS TURBINE TEST SET

Pelton turbine with stainless steel runner, nozzle and metal housing with transparent window. Francis turbine with Metal runner, adjustable guide vanes and casing with transparent window. Maximum output: 25-40 W.

HT 201 MINI PELTON TURBINE TEST SET

Stainless steel runner, and nozzle.

Non-corrosion metal housing and transparent window. Maximum output: Over 40 W.

HT 501A MINI AXIAL FLOW PROPELLER TURBINE TEST SET

Maximum output: Over 15 W.

HT 501AI MINI AXIAL FLOW IMPULSE TURBINE TEST SET

Maximum output: Over 25 W.

HT 601 MINI KAPLAN TURBINE TEST SET

Maximum power: Over 15 W.

HT 301 MINI FRANCIS TURBINE TEST SET

Maximum output: Over 25 W.

HT 203 COMPACT PELTON TURBINE TEST SET

Maximum output: 450 W.

HT 303 COMPACT FRANCIS TURBINE TEST SET Bronze runner, adjustable guide vanes and casing with transparent window. Maximum output: 400 W.

HT 403 COMPACT CROSS FLOW TURBINE TEST SET

Maximum output: 400 W.

HT 603 COMPACT KAPLAN TURBINE TEST SET

Maximum output: 400 W.

HT 702 COMPACT PELTON / FRANCIS TURBINE TEST SET

Pelton turbine with stainless steel runner, nozzle and casing with transparent window. Francis turbine with bronze runner, adjustable guide vanes and casing with transparent window. Maximum output: 400 - 450 W.

HT 703 MULTI TURBINE TEST SET Stainless steel runner Pelton turbine, bronze runner. Francis turbine, stainless steel runner cross-flow turbine and stainless steel runner Kaplan turbine. Maximum output: 400-450 W.

LARGE TURBINE TEST SETSThese are large turbine test set with 7.5 kW pump,storage tank and measuring instruments.

Direct coupling electric generator.

HT 210 PELTON TURBINE TEST SETStainless steel runner. Stainless steel nozzle and casing with transparent window.

Maximum output:2000 W .

HT 410CROSSFLOW TURBINE TEST SETHT 610KAPLAN TURBINE TEST SET

HT 310 FRANCIS TURBINE TEST SET HT 210 PELTON TURBINE TEST SET

This equipment is designed to the study of air flow measurement performance of fan, blower and compressor as well as related flow

behavior. DEMONSTRATION UNIT, Computer Interface

FAN AND BLOWER (SMALL AND LARGE SIZE)

WIND TUNNELS

MP 111 MULTI STAGE CENTRIFUGAL AIR COMPRESSOR DEMONSTRATION UNIT, Computer Interface

A bench top unit with 1 kW two stage compressor, inlet orifice, outlet damper, sensors and software. To be used with computer.

MP 121 AXIAL FLOW FAN DEMONSTRATION UNIT, Computer Interface

A bench top unit with 24 W axial flow fan and motor, inlet orifice, outlet damper, flow straighteners, sensors and software. To be used with computer.

MP 110 CENTRIFUGAL FAN DEMONSTRATION UNIT,

Computer Interface A bench top unit with centrifugal fan, 0.75 kW motor, inlet orifice, outlet damper; sensors and software. To be used with computer.

MP 100 AIR FLOW BENCH A centrifugal fan with 0.55 kW motor, inlet pipe, outlet pipe with damper, flow straighteners, orifice plate, nozzle, inlet cone, travelling pitot, inclined and multi tube manometers and optional items.

MP 124 AXIAL FLOW FAN TEST SET Axial flow fan with 2.2 kW motor and an advanced inverter, flow straightener, guide vane, outlet damper, measuring instruments and other optional items.

MP 142 FLOW VISUALIZATION WIND TUNNEL This is a unit for visualization of air flow stream lines around models. It consists of a stilling entrance, a viewing window, models, a smoke generator and distributor and a small blower.

MP 115 COMPACT CENTRIFUGAL FAN TEST SET

Bench top unit with centrifugal fan, 0.75 kW motor, advanced inverter, inlet orifice, outlet damper, inclined manometer, hand tachometer, thermometer and barometer.

MP 125 COMPACT AXIAL FLOW FAN TEST SET Bench top unit with 24 W axial flow fan and motor, inlet orifice, outlet damper, speed indicator, inclined manometer, ammeter, voltmeter, thermometer and barometer.

MP 119 CENTRIFUGAL BLOWER TEST SET A centrifugal blower and 2.2 kW motor with an advanced inverter, outlet amper, flow straighteners,

orifice plate, Venturi nozzle, inclined manometers

MP 315D SUBSONIC WIND TUNNEL, Downstream Fan An axial flow with 0.75 kW variable speed motor, 150 mm x 150 mm test section, maximum air speed over 30 m/sec, two component balance, various accessories and models. Optional: Computer interface and computer control.

and measuring instruments.

15

AIR FLOW AND AIR COMPRESSION

AIR COMPRESSION A single stage and two stage air compressor with and advanced inverter, air box with inlet orifice and inclined manometer, air receiver and

measuring instruments.

MP 330D SUBSONIC WIND TUNNEL, Downstream Fan An axial flow fan with 2.2 kW variable speed motor, 300 mm x 300 mm test section, maximum air speed over 30 m/sec, two components balance, various accessories and models. Optional: Computer interface and computer control.

MP 330U SUBSONIC WIND TUNNEL, Upstream Fan Similar to MP 330D but with upstream fan. Optional: Computer interface and computer control. MP 330UH SUBSONIC WIND TUNNEL, Upstream Fan Similar to MP 330U but with 7.5 kW fan and maximum air speed over 60 m/sec. Optional: Computer interface and computer control.

MP 202 TWO STAGE AIR COMPRESSOR TEST SET, Air Cooled

2.2 kW motor

MP 201 SINGLE STAGE AIR COMPRESSOR TEST SET, Air Cooled

1.5 kW motor

MP 203 TWO STAGE AIR COMPRESSOR TEST SET, Air-Water Cooled

2.2 kW motor, different speeds for the two stages, water cooled intercooler.

RE 210 SOLAR ELECTICITY The unit consists of a solar panel, an inverter, a regulator, a storage battery, and a load circuit, a motor and measuring instrument. A computer interface unit and software. Panel rating: 60 W.

RE 310 EDUCATIONAL WIND TURBINE 500 mm diameter transparent casing test section with adjustable wind speed up to 20 m/sec Turbine wheel with 2 to 4 adjustable angle blades. Dynamometer, generator with lamp load and measuring instruments. Larger diameter is also available.

HT 903 MINI HYDRO POWER PLANT A self-contained unit. 2. 2 kW pump, cross flow turbine with stainless steel runner, nozzle and casing, transparent window. AC generator with lamp loads. Storage tank and measuring instruments. Maximum electrical output: up to 300 W, 220 V, 1 Ph, 50 Hz.

The equipment in this group includes internal combustion engines, heat exchangers, refrigeration and air conditioning, boilers and steam power

plants and others.

INTERNAL COMBUSTION ENGINES TEST BEDSThis test bed is for measurement of speed, torque, output power, fuel consumption, air flow rate and temperatures of a single cylinder or multi

cylinder for gasoline or diesel engine for determination of efficiencies, Air/Fuel ratio etc.

MT 501M SINGLE CYLINDER ENGINE TEST BED, Mechanical Brake Absorber

Optional: Computer Interface

MT 503G SINGLE CYLINDER ENGINE TEST BED, Electric Generator Absorber

Optional: Computer interface.

MT 505 AUTOMOTIVE ENGINE TEST BED Optional: Computer Interface MT 505C AUTOMOTIVE ENGINE TEST BED,

Computer Control

MT 511 MOTOR CYCLE DYNAMOMETER This is a chassis type dynamometer for measurement of dynamometer speed, torque, output power and vehicle speed of a motor cycle. Capacity: upto 150 kW. Optional: - Eddy current absorber

- Computer interface.

MT 520 EXHAUST GAS COLORIMETER Stainless steel finned tubes and casing with gas to water heat exchanger for use on multi cylinder engine.

MT 502 SINGLE CYLINDER ENGINE TEST BED

Optional: Computer Interface MT 502C SINGLE CYLINDER ENGINE

TEST BED, Computer Control

Model

Type of Dynamometer

Type of engine Mechanical

Brake Hydraulic

Brake Generator Air Cooled Eddy

CurrentBrake Brake

Water Cooled Eddy Current

MT501 Single Cylinder o - - - -

MT502 Single Cylinder - o - o -

MT503 Single Cylinder - - o - -

MT505 Multi Cylinder - o - o o

16

AIR FLOW AND AIR COMPRESSION

RENEWABLE ENERGY

AIR COMPRESSION A single stage and two stage air compressor with and advanced inverter, air box with inlet orifice and inclined manometer, air receiver and

measuring instruments.

MP 330D SUBSONIC WIND TUNNEL, Downstream Fan An axial flow fan with 2.2 kW variable speed motor, 300 mm x 300 mm test section, maximum air speed over 30 m/sec, two components balance, various accessories and models. Optional: Computer interface and computer control.

MP 330U SUBSONIC WIND TUNNEL, Upstream Fan Similar to MP 330D but with upstream fan. Optional: Computer interface and computer control. MP 330UH SUBSONIC WIND TUNNEL, Upstream Fan Similar to MP 330U but with 7.5 kW fan and maximum air speed over 60 m/sec. Optional: Computer interface and computer control.

MP 202 TWO STAGE AIR COMPRESSOR TEST SET, Air Cooled

2.2 kW motor

MP 201 SINGLE STAGE AIR COMPRESSOR TEST SET, Air Cooled

1.5 kW motor

MP 203 TWO STAGE AIR COMPRESSOR TEST SET, Air-Water Cooled

2.2 kW motor, different speeds for the two stages, water cooled intercooler.

RE 210 SOLAR ELECTICITY The unit consists of a solar panel, an inverter, a regulator, a storage battery, and a load circuit, a motor and measuring instrument. A computer interface unit and software. Panel rating: 60 W.

RE 310 EDUCATIONAL WIND TURBINE 500 mm diameter transparent casing test section with adjustable wind speed up to 20 m/sec Turbine wheel with 2 to 4 adjustable angle blades. Dynamometer, generator with lamp load and measuring instruments. Larger diameter is also available.

HT 903 MINI HYDRO POWER PLANT A self-contained unit. 2. 2 kW pump, cross flow turbine with stainless steel runner, nozzle and casing, transparent window. AC generator with lamp loads. Storage tank and measuring instruments. Maximum electrical output: up to 300 W, 220 V, 1 Ph, 50 Hz.

The equipment in this group includes internal combustion engines, heat exchangers, refrigeration and air conditioning, boilers and steam power

plants and others.

INTERNAL COMBUSTION ENGINES TEST BEDSThis test bed is for measurement of speed, torque, output power, fuel consumption, air flow rate and temperatures of a single cylinder or multi

cylinder for gasoline or diesel engine for determination of efficiencies, Air/Fuel ratio etc.

MT 501M SINGLE CYLINDER ENGINE TEST BED, Mechanical Brake Absorber

Optional: Computer Interface

MT 503G SINGLE CYLINDER ENGINE TEST BED, Electric Generator Absorber

Optional: Computer interface.

MT 505 AUTOMOTIVE ENGINE TEST BED Optional: Computer Interface MT 505C AUTOMOTIVE ENGINE TEST BED,

Computer Control

MT 511 MOTOR CYCLE DYNAMOMETER This is a chassis type dynamometer for measurement of dynamometer speed, torque, output power and vehicle speed of a motor cycle. Capacity: upto 150 kW. Optional: - Eddy current absorber

- Computer interface.

MT 520 EXHAUST GAS COLORIMETER Stainless steel finned tubes and casing with gas to water heat exchanger for use on multi cylinder engine.

MT 502 SINGLE CYLINDER ENGINE TEST BED

Optional: Computer Interface MT 502C SINGLE CYLINDER ENGINE

TEST BED, Computer Control

Model

Type of Dynamometer

Type of engine Mechanical

Brake Hydraulic

Brake Generator Air Cooled Eddy

CurrentBrake Brake

Water Cooled Eddy Current

MT501 Single Cylinder o - - - -

MT502 Single Cylinder - o - o -

MT503 Single Cylinder - - o - -

MT505 Multi Cylinder - o - o o

17

THERMODYNAMICS

GAS TURBINES

HEAT EXCHANGERS

MT 551 TURBO JET ENGINE, 70N Thrust A radial flow compressor and an axial flow turbine as in modern air planes with motor start. Complete with sensors, signal converter and software for data display, analysis and control by computer. MT 553 TURBO JET ENGINE, 200N Thrust.

MT 560 TWO SHAFT GAS TURBINE A radial flow compressor and axial flow turbine and the other is axial flow power turbine as in modern power plants. Indirect coupling dynamometer. Sensors, signal converter with software for data display, analysis and control by computer.

TH 150 MINI GAS TURBINE POWER PLANT Similar to MT560 with AC generator and lamp loads instead of dynamometer.

TH 241 MULTI HEAT EXCHANGER, Transparent Casing The unit has three heat exchangers-concentric tube, shell and tube and plate. The concentric tube and shell and tube are transparent casing. Accessories include pump water tank, heater and measuring instruments. Selection of the heat exchanger is by selection valves. Changing the flow direction is by switching the hoses. Optional: Jacketed vessel with coil and stirrer. Computer interface or computer control.

TH 240 MULTI HEAT EXCHANGER Similar to TH241 with larger heat transfer area and opaquecasing of concentric /shell and tube.Optional: Jacketed vessel with coil and stirrer.

Computer interface or computer control.

TH 231 JACKETED VESSEL WITH COIL AND STIRRER

TH 201 CONCENTRIC TUBE HEAT EXCHANGER TH 203 CONCENTRIC TUBE HEAT EXCHANGER, Different Tube Metals TH 211 SHELL AND TUBE HEAT EXCHANGER TH 221 PLATE HEAT EXCHANGER

TH 202 CONCENTRIC TUBE HEAT EXCHANGER, Transparent Casing

. TH 212 SHELL AND TUBE HEAT EXCHANGER,

Transparent Casing

HEAT TRANSFER

TH 260 BOILING HEAT TRANSFER UNIT A low boiling point liquid is boiled by a heater in a glass cylinder. The vapor is condensed by a water-cooled condenser and measuring instruments.

TH 251 DEMONSTRATION COOLING TOWERTransparent packed column completes with blower, circulating pump, stainless steel tanks, heater and measuring instruments Optional: - Other packed columns

- Computer interface

TH 312 THERMAL CONDUCTIVITY OF NON METALLIC MATERIALS, Guarded hot plate method

Specimen is clamped between a hot plate with heater and a cold plate with cooling water and measuring instruments.

TH 310 HEAT CONDUCTION A linear and radial heat conduction study unit complete with cooling system, heater, different heat conduction materials and cross-section, measuring instruments. Optional: computer interface

TH 320 FREE AND FORCED CONVECTION Vertical duct and heater with flat, cylindrical and fin heating surfaces. Exhaust fan, anemometer and measuring instruments. Optional: Computer interface

TH 501 TEMPERATURE MEASURING BENCH Demonstration of temperature measuring devices: resistance, thermistor, thermo-couple, bimetallic, vapor pressure, liquid in glass, self-adhesive indicator etc.

TH 410 STIRLING CYCLE HOT AIR ENGINE, Horizontal Cylinders The engine consists of two horizontal cylinders for hot air generation and power generation and measuring instruments. Maximum power: over 1000 mW.

TH 413 STIRLING CYCLE HOT AIR ENGINE, Twin Power The engine is quick start with water cooled hot air cylinder, two power cylinders and measuring instruments. Maximum output power: 3000 mW.

TH 411 STIRLING CYCLE HOT AIR ENGINE, Vertical Cylinders The engine is quick start and consists of two vertical cylinders for hot air generation and power generation and measuring instruments. Maximum output power: 900 mW.

TH 330 THERMAL RADIATION Radiant heat source and light source. Radiation measuring devices and accessories are mounted on aluminum profile frame with track scale. Measuring instruments. Optional: Computer interface

18

THERMODYNAMICS

GAS TURBINES

HEAT EXCHANGERS

MT 551 TURBO JET ENGINE, 70N Thrust A radial flow compressor and an axial flow turbine as in modern air planes with motor start. Complete with sensors, signal converter and software for data display, analysis and control by computer. MT 553 TURBO JET ENGINE, 200N Thrust.

MT 560 TWO SHAFT GAS TURBINE A radial flow compressor and axial flow turbine and the other is axial flow power turbine as in modern power plants. Indirect coupling dynamometer. Sensors, signal converter with software for data display, analysis and control by computer.

TH 150 MINI GAS TURBINE POWER PLANT Similar to MT560 with AC generator and lamp loads instead of dynamometer.

TH 241 MULTI HEAT EXCHANGER, Transparent Casing The unit has three heat exchangers-concentric tube, shell and tube and plate. The concentric tube and shell and tube are transparent casing. Accessories include pump water tank, heater and measuring instruments. Selection of the heat exchanger is by selection valves. Changing the flow direction is by switching the hoses. Optional: Jacketed vessel with coil and stirrer. Computer interface or computer control.

TH 240 MULTI HEAT EXCHANGER Similar to TH241 with larger heat transfer area and opaquecasing of concentric /shell and tube.Optional: Jacketed vessel with coil and stirrer.

Computer interface or computer control.

TH 231 JACKETED VESSEL WITH COIL AND STIRRER

TH 201 CONCENTRIC TUBE HEAT EXCHANGER TH 203 CONCENTRIC TUBE HEAT EXCHANGER, Different Tube Metals TH 211 SHELL AND TUBE HEAT EXCHANGER TH 221 PLATE HEAT EXCHANGER

TH 202 CONCENTRIC TUBE HEAT EXCHANGER, Transparent Casing

. TH 212 SHELL AND TUBE HEAT EXCHANGER,

Transparent Casing

HEAT TRANSFER

TH 260 BOILING HEAT TRANSFER UNIT A low boiling point liquid is boiled by a heater in a glass cylinder. The vapor is condensed by a water-cooled condenser and measuring instruments.

TH 251 DEMONSTRATION COOLING TOWERTransparent packed column completes with blower, circulating pump, stainless steel tanks, heater and measuring instruments Optional: - Other packed columns

- Computer interface

TH 312 THERMAL CONDUCTIVITY OF NON METALLIC MATERIALS, Guarded hot plate method

Specimen is clamped between a hot plate with heater and a cold plate with cooling water and measuring instruments.

TH 310 HEAT CONDUCTION A linear and radial heat conduction study unit complete with cooling system, heater, different heat conduction materials and cross-section, measuring instruments. Optional: computer interface

TH 320 FREE AND FORCED CONVECTION Vertical duct and heater with flat, cylindrical and fin heating surfaces. Exhaust fan, anemometer and measuring instruments. Optional: Computer interface

TH 501 TEMPERATURE MEASURING BENCH Demonstration of temperature measuring devices: resistance, thermistor, thermo-couple, bimetallic, vapor pressure, liquid in glass, self-adhesive indicator etc.

TH 410 STIRLING CYCLE HOT AIR ENGINE, Horizontal Cylinders The engine consists of two horizontal cylinders for hot air generation and power generation and measuring instruments. Maximum power: over 1000 mW.

TH 413 STIRLING CYCLE HOT AIR ENGINE, Twin Power The engine is quick start with water cooled hot air cylinder, two power cylinders and measuring instruments. Maximum output power: 3000 mW.

TH 411 STIRLING CYCLE HOT AIR ENGINE, Vertical Cylinders The engine is quick start and consists of two vertical cylinders for hot air generation and power generation and measuring instruments. Maximum output power: 900 mW.

TH 330 THERMAL RADIATION Radiant heat source and light source. Radiation measuring devices and accessories are mounted on aluminum profile frame with track scale. Measuring instruments. Optional: Computer interface

19

THERMODYNAMICS

TH 525 AIR-TO-WATER HEAT PUMP A bench top unit with compressor, a water cooled condenser, the evaporator absorbs heat from environmental air and measuring instruments.

TH 522 ICE MAKER TEST RIG A bench top unit with compressor, an ice maker evaporator, air cooled condenser and measuring instruments.

TH 527 REFRIGERATION TRAINER A bench top unit with compressor, a water cooled condenser, water cooled evaporator and measuring instruments.

TH 102 TRAINING BOILER, 200 kg/h, 10 kg/cm2 A vertical water tube boiler complete with feed water system, fuel system, safety devices and control panel. Optional: - Super heater

- Condenser - Cooling tower etc.

TH101 Training Boiler, 100 kg/h, 10 kg/cm2

AIR CONDITIONING AND REFRIGERATION

BOILER AND POWER PLANTS

TH 511 SPLIT TYPE AIR CONDITIONER SYSTEM, Inverter Control

TH 510 SPLIT TYPE AIR CONDITIONER SYSTEM 2.5 kW unit, with wall type fan coil, R22 refrigerant and measuring instruments.

TH 512 CAR AIR CONDITIONING SYSTEM 3.7 kW motor with compressor, radiator, automotive air condition fan, R 134a refrigerant and measuring instruments.

TH 516 LABORATORY AIR CONDITIONING SYSTEM The system has a transparent window. A humidifier, a preheater, and a reheater are provided in addition to the normal fan, compressor and cooling unit.

TH 518 RECIRCULATION AIR CONDITIONING UNIT, With Climatic Chamber The system has a transparent window. A humidifier and a preheater are provided in addition to the normal fan, compressor and cooling unit. A humidifier and a reheater are provided in the climatic chamber.

TH 520 BASIC REFRIGERATION SYSTEM 70 W compressor, with transparent windowfreezer, air cooled condenser, sight glassesand measuring instruments.

TH 124 MARCET BOILER Pressure: 15 kg/cm2. Temperature: 200ºC.

TH 120 MINI STEAM POWER PLANT An educational miniature power plant consisting of feed water tank with hand feed pump, gas fired boiler, steam engine, condenser, generator and loads, prony brake and measuring instruments. Maximum power: over 5 W

TH 130 MINI STEAM TURBINE POWER PLANT A miniature modern power plant for education consisting of feed water tank with hand feed pump, gas fired boiler, steam turbine, condenser, generator and loads, prony brake and measuring instruments. Maximum power: over 9 W. Optional: Super heater, Computer interface, Automatic feed pump

TH 137 COMPACT STEAMTURBINE POWER PLANT, 1.5 kW A compact steam turbine power plant for education consisting of a 300 kg/h water tube boiler, feed water system, fuel system, a steam turbine anda generator, lamp loads, a condenser, and a cooling tower.

TH 136 COMPACT STEAM TURBINE POWER PLANT, 1.0 kW Similar to TH 137 with 200 kg/h boiler. TH 135 COMPACT STEAM TURBINEPOWER PLANT, 0.5 kW Similar to TH 137 with 100 kg/h boiler.

Optional: - Electric boiler instead of diesel boiler. - Super heater, Electric - Water brake absorber dynamometer - Computer interface or Computer control

20

THERMODYNAMICS

TH 525 AIR-TO-WATER HEAT PUMP A bench top unit with compressor, a water cooled condenser, the evaporator absorbs heat from environmental air and measuring instruments.

TH 522 ICE MAKER TEST RIG A bench top unit with compressor, an ice maker evaporator, air cooled condenser and measuring instruments.

TH 527 REFRIGERATION TRAINER A bench top unit with compressor, a water cooled condenser, water cooled evaporator and measuring instruments.

TH 102 TRAINING BOILER, 200 kg/h, 10 kg/cm2 A vertical water tube boiler complete with feed water system, fuel system, safety devices and control panel. Optional: - Super heater

- Condenser - Cooling tower etc.

TH101 Training Boiler, 100 kg/h, 10 kg/cm2

AIR CONDITIONING AND REFRIGERATION

BOILER AND POWER PLANTS

TH 511 SPLIT TYPE AIR CONDITIONER SYSTEM, Inverter Control

TH 510 SPLIT TYPE AIR CONDITIONER SYSTEM 2.5 kW unit, with wall type fan coil, R22 refrigerant and measuring instruments.

TH 512 CAR AIR CONDITIONING SYSTEM 3.7 kW motor with compressor, radiator, automotive air condition fan, R 134a refrigerant and measuring instruments.

TH 516 LABORATORY AIR CONDITIONING SYSTEM The system has a transparent window. A humidifier, a preheater, and a reheater are provided in addition to the normal fan, compressor and cooling unit.

TH 518 RECIRCULATION AIR CONDITIONING UNIT, With Climatic Chamber The system has a transparent window. A humidifier and a preheater are provided in addition to the normal fan, compressor and cooling unit. A humidifier and a reheater are provided in the climatic chamber.

TH 520 BASIC REFRIGERATION SYSTEM 70 W compressor, with transparent windowfreezer, air cooled condenser, sight glassesand measuring instruments.

TH 124 MARCET BOILER Pressure: 15 kg/cm2. Temperature: 200ºC.

TH 120 MINI STEAM POWER PLANT An educational miniature power plant consisting of feed water tank with hand feed pump, gas fired boiler, steam engine, condenser, generator and loads, prony brake and measuring instruments. Maximum power: over 5 W

TH 130 MINI STEAM TURBINE POWER PLANT A miniature modern power plant for education consisting of feed water tank with hand feed pump, gas fired boiler, steam turbine, condenser, generator and loads, prony brake and measuring instruments. Maximum power: over 9 W. Optional: Super heater, Computer interface, Automatic feed pump

TH 137 COMPACT STEAMTURBINE POWER PLANT, 1.5 kW A compact steam turbine power plant for education consisting of a 300 kg/h water tube boiler, feed water system, fuel system, a steam turbine anda generator, lamp loads, a condenser, and a cooling tower.

TH 136 COMPACT STEAM TURBINE POWER PLANT, 1.0 kW Similar to TH 137 with 200 kg/h boiler. TH 135 COMPACT STEAM TURBINEPOWER PLANT, 0.5 kW Similar to TH 137 with 100 kg/h boiler.

Optional: - Electric boiler instead of diesel boiler. - Super heater, Electric - Water brake absorber dynamometer - Computer interface or Computer control

21

THERMODYNAMICS

BP 105 FLUID MIXING TANK For a study of mixing of two materials under various conditions. The equipment comprises a mixing tank with removable baffles, a variable speed agitator and various impellers, speed and torque measuring instrument.

Optional: An air compressor and a rotameter

BP 120 FIXED & FLUIDIZED BED APPARATUS Two beds, one for air and the other for water, for a study of fluid bubbling phenomena. Air compressor, water pump, rotameters, manometers and bed material are provided.

BP 213 KINETIC REACTORS IN SERIES The unit is designed for a study of multistage mixing process. The equipment comprises two reagent tanks with pumps and rotameters, three reactor tanks with variable speed agitators and conductivity probes.

HM 120 FLUIDIZATION AND HEAT TRANSFER

HM 130 GAS ABSORPTION COLUMN Packed column with raschig rings 1.4 m high, feed tank, pump, air blower, manometers, rotameters, carbon dioxide bottle and a gas analyser.

HM 210 BATCH DISTILLATION UNIT Plate column with view port and packed column with reboiler, condenser, condensate vessel, reflux valve and sampling points, manometer, rotameter and temperature digital display.

TH 610 TRAY DRYER Square duct with fan, heater, drying trays, balance and anemometer.

MP 400 CYCLONE SEPARATOR A variable speed blower with hopper and variable speed feeder, cyclone, dust box with filter, travelling Pitot tube and manometers.

BP 310 DEEP BED FILTER COLUMN Raw water contaminated with solids is filtered through deep sand bed in a transparent column. The column has pressure tapping and coupling points along its height. Raw water tank, treated water tank with pump, piping and rotameter are provided.

HF 112 LIQUID SEDIMENTATION APPARATUS

For study, the settling characteristics and particle sizes of suspended solid.

The equipment is for a study of fluidized bed behavior and heat transfer coefficient. The equipment includes a glass cylinder, a heater with temperature probes and digital display, air rotameters, manometers, volt meter, ammeter and bed material.

Equipments in this group measure behavior of materials under various types of load i.e. tension, compression, bending, torsion, cyclic load, impact etc.

TM 235 CHARPY IMPACT TESTING MACHINE, 150/300 J Charpy impact test, 150 x 1 J and 300 x 2 J hammer, worm gear lifting. Complete with energy digital display brake and guard. Optional Motorized lifting, accessories for Izod test.

TM 232 CHARPY IMPACT TESTING MACHINE, 25/50 J.

Charpy impact test, 25 x 0.25 J and50 x 0.5 J complete with energyindicator brake and guard.

TM115B UNIVERSAL TESTING MACHINE, 50 kN, Ball Screw

The universal testing machine uses four columns in two planes and a hand operated ball screw with measuring instruments for load and displacement. TM 115A UNIVERSAL TESTING

MACHINE, 50 kN. Similar to TM115B with hand operatedhydraulic jack.

TM 442 THICK CYLINDER Thick wall aluminium alloy cylinder with hydraulic hand pump. Strain gauges at various wall thickness, bridge box and strain digital display.

TM 445 CIRCULAR DIAPHRAM Circular aluminium alloy diaphragm with hydraulic hand pump for internal pressure, dial gauge for deflection measurement, strain gauges at various positions, bridge box and strain digital display.

TM 441 THIN CYLINDER Thin wall aluminium alloy cylinder with hydraulic hand pump for internal pressure and closed-end / open-end conditions, strain gauges at various positions, bridge box and strain digital display.

TM 113A UNIVERSAL TESTING MACHINE, 30 kN.

The universal testing machine uses four in-line columns and a hand operated hydraulic jack with measuring instruments for load and displacement. TM113B UNIVERSAL TESTING

MACHINE, 30 kN, Ball Screw Similar to TM113A with hand operatedball screw.

TM 450 UNSYMMETRICAL CANTILEVER APPARATUS

Three types of cantilever sections with mounted end rotation and free end load application, dial gauges for measurement of vertical and horizontal displacements.

TM 411 STRUT BUCKLING APPARATUS Twin columns with screw loading, loading indicator and dial gauge for deflection measurement. Simply support and built-in end conditions, struts of various sizes and materials.

TM 203M TORSION TESTING MACHINE, 200 Nm.

Similar to TM203E with hand operated.

TM 211 FATIGUE TESTING MACHINE A specimen is clamped to a rotating shaft with spring balance loading. Speed indicated revolution counter is provided.

TM 221 CREEP TESTING MACHINE Loading by lever with weights, creep measurement by dial indicator, glycol pack for specimen temperature control, test specimens.

TM 415 BEAM APPARATUS Aluminium profile frame, 3 sinking load cells, cantilever support, 3 dialgauges for deflection measurement, hangers and weights, beam ofdifferent materials and sections.

TM 201 TORSION TESTING MACHINE, 30 Nm. A reversible, hand operated gear reducer with revolution counter and angular scales, torque indicator, calibration weights, test specimens.

TM 203E TORSION TESTING MACHINE, 200 Nm.

The machine consists of a torque measuring unit, motorized two stage reduction gear, angular and digital display. The motor is automaticallystopped when the specimen is broken.

torque

Optional: Computer Control.

22

CHEMICAL ENGINEERING AND FOOD TECHNOLOGY

BP 105 FLUID MIXING TANK For a study of mixing of two materials under various conditions. The equipment comprises a mixing tank with removable baffles, a variable speed agitator and various impellers, speed and torque measuring instrument.

Optional: An air compressor and a rotameter

BP 120 FIXED & FLUIDIZED BED APPARATUS Two beds, one for air and the other for water, for a study of fluid bubbling phenomena. Air compressor, water pump, rotameters, manometers and bed material are provided.

BP 213 KINETIC REACTORS IN SERIES The unit is designed for a study of multistage mixing process. The equipment comprises two reagent tanks with pumps and rotameters, three reactor tanks with variable speed agitators and conductivity probes.

HM 120 FLUIDIZATION AND HEAT TRANSFER

HM 130 GAS ABSORPTION COLUMN Packed column with raschig rings 1.4 m high, feed tank, pump, air blower, manometers, rotameters, carbon dioxide bottle and a gas analyser.

HM 210 BATCH DISTILLATION UNIT Plate column with view port and packed column with reboiler, condenser, condensate vessel, reflux valve and sampling points, manometer, rotameter and temperature digital display.

TH 610 TRAY DRYER Square duct with fan, heater, drying trays, balance and anemometer.

MP 400 CYCLONE SEPARATOR A variable speed blower with hopper and variable speed feeder, cyclone, dust box with filter, travelling Pitot tube and manometers.

BP 310 DEEP BED FILTER COLUMN Raw water contaminated with solids is filtered through deep sand bed in a transparent column. The column has pressure tapping and coupling points along its height. Raw water tank, treated water tank with pump, piping and rotameter are provided.

HF 112 LIQUID SEDIMENTATION APPARATUS

For study, the settling characteristics and particle sizes of suspended solid.

The equipment is for a study of fluidized bed behavior and heat transfer coefficient. The equipment includes a glass cylinder, a heater with temperature probes and digital display, air rotameters, manometers, volt meter, ammeter and bed material.

Equipments in this group measure behavior of materials under various types of load i.e. tension, compression, bending, torsion, cyclic load, impact etc.

TM 235 CHARPY IMPACT TESTING MACHINE, 150/300 J Charpy impact test, 150 x 1 J and 300 x 2 J hammer, worm gear lifting. Complete with energy digital display brake and guard. Optional Motorized lifting, accessories for Izod test.

TM 232 CHARPY IMPACT TESTING MACHINE, 25/50 J.

Charpy impact test, 25 x 0.25 J and50 x 0.5 J complete with energyindicator brake and guard.

TM115B UNIVERSAL TESTING MACHINE, 50 kN, Ball Screw

The universal testing machine uses four columns in two planes and a hand operated ball screw with measuring instruments for load and displacement. TM 115A UNIVERSAL TESTING

MACHINE, 50 kN. Similar to TM115B with hand operatedhydraulic jack.

TM 442 THICK CYLINDER Thick wall aluminium alloy cylinder with hydraulic hand pump. Strain gauges at various wall thickness, bridge box and strain digital display.

TM 445 CIRCULAR DIAPHRAM Circular aluminium alloy diaphragm with hydraulic hand pump for internal pressure, dial gauge for deflection measurement, strain gauges at various positions, bridge box and strain digital display.

TM 441 THIN CYLINDER Thin wall aluminium alloy cylinder with hydraulic hand pump for internal pressure and closed-end / open-end conditions, strain gauges at various positions, bridge box and strain digital display.

TM 113A UNIVERSAL TESTING MACHINE, 30 kN.

The universal testing machine uses four in-line columns and a hand operated hydraulic jack with measuring instruments for load and displacement. TM113B UNIVERSAL TESTING

MACHINE, 30 kN, Ball Screw Similar to TM113A with hand operatedball screw.

TM 450 UNSYMMETRICAL CANTILEVER APPARATUS

Three types of cantilever sections with mounted end rotation and free end load application, dial gauges for measurement of vertical and horizontal displacements.

TM 411 STRUT BUCKLING APPARATUS Twin columns with screw loading, loading indicator and dial gauge for deflection measurement. Simply support and built-in end conditions, struts of various sizes and materials.

TM 203M TORSION TESTING MACHINE, 200 Nm.

Similar to TM203E with hand operated.

TM 211 FATIGUE TESTING MACHINE A specimen is clamped to a rotating shaft with spring balance loading. Speed indicated revolution counter is provided.

TM 221 CREEP TESTING MACHINE Loading by lever with weights, creep measurement by dial indicator, glycol pack for specimen temperature control, test specimens.

TM 415 BEAM APPARATUS Aluminium profile frame, 3 sinking load cells, cantilever support, 3 dialgauges for deflection measurement, hangers and weights, beam ofdifferent materials and sections.

TM 201 TORSION TESTING MACHINE, 30 Nm. A reversible, hand operated gear reducer with revolution counter and angular scales, torque indicator, calibration weights, test specimens.

TM 203E TORSION TESTING MACHINE, 200 Nm.

The machine consists of a torque measuring unit, motorized two stage reduction gear, angular and digital display. The motor is automaticallystopped when the specimen is broken.

torque

Optional: Computer Control.

23

STRENGTH AND PROPERTIES OF MATERIALS

This group of equipment includes simple equipments for force study, mechanism for a study of machine motion and equipment for more

advanced force and motion study.

MECHANISM FOR MOTION STUDY

FORCE AND MOTION STUDY

MM 211H SLIDER CRANK For demonstration of relative motion between crank rotation and slider translation as found in internal combustion engines.

MM 212H FOUR BAR LINKAGE For demonstration of relative motion between crank rotation and another link oscillation (swinging).

MM 213H SLOTTED LINK For demonstration of relative motion between crank rotation and slider translation through another oscillating link resulting in quick return for slider motion.

MM 214H WHITWORTH QUICK RETURN For demonstration of relative motion between crank rotation and slider translation through another offset rotating member resulting in quick return for slider motion. MM 216H OLDHAM COUPLING For demonstration of relative angular motion between two shafts with parallel but displaced axes.

MM 215H SCOTCH YOKE For demonstration of relative motion between crank rotation and a yoke translation.

MM 219H GENEVA STOP For demonstration of relative angular motion between two parallel shafts – one with continuous rotation, the other with intermittent rotation.

MM 220H CAM AND FOLLOWER For demonstration of relative motion between a rotating eccentric member (cam) and sliding member (follower) translation as found in internal combustion engines.

MM 221 EPICYCLE GEAR TRAIN For demonstration of relative angular motion between two shafts with common axis using sun and planetary gears to produce a forward speed.

MM 222 DOUBLE EPICYCLIC GEAR TRAIN For demonstration of relative angular motion between three shafts with common axis using two epicyclic trains to produce two forward speeds or a forward and a reverse.

MM 223 TRIPLE EPICYCLIC GEAR TRAIN

For demonstration of relative angular motion between four shafts with common axis using three epicyclic trains to produce two forward speeds and a reverse.

MM 312 TORSIONAL OSCILLATIONS APPARATUS

This mechanism demonstrates torsional oscillations of single or multi-rotor and /or geared systems with low natural frequencies.

MM 240 SIMPLE GEARED SYSTEM For determination of system inertia. A system of 12 gears and 4 shafts. Complete with load hanger, weights, measuring tape, stop watch and cord.

MM 242 COMPREHENSIVE GEARED SYSTEM For determination of system inertia and efficiency. Three shafts with fixed and sliding gears, motor dynamometer, inverter, mechanical brake dynamometer, sensors with digital display, weight hanger, weights

and masses.

MM 246 AUTOMOTIVE GEAR SYSTEM EFFICIENCY, Manual Transmission

A bench top unit with five-speed automotive manual gear box, input motor dynamometer, inverter, output dynamometer and measuring instruments for a study of gear efficiency at different loads, speeds and gear ratios. MM 245 AUTOMOTIVE GEAR SYSTEM, Manual Transmission Similar to MM246 with floor standing design and accessories for studying of equivalent gear inertia.

MM 500 MECHANICAL ENGINEERING TEST SETS

MM 500-111 FORCES SET The set consists of plastic plates, angular scale, pulleys, weight hangers and weights, cords and rings, and protactor. The experiments include center of gravity, force triangle, force polygon, Bow’s notation, and non-concurrent forces.

MM 500-112 MOMENTS SET The set consists of riqid beam, crank lever with hook points, spring balances, pulley, weight hangers and weights, cord and hooks. The experiments include principles of moments, beam balances, levers and beam reactions.

MM 500-115 SHEAR AND BENDING MOMENT SET

The apparatus consists of two-part beams and spring attachments, beam supports, spring balances, weight hangers and weights. The experiments include determination of shear force and bending moment on a beam under loads. MM 500-114 SHEAR FORCE SET MM 500-113 BENDING MOMENT SET

MM 500-117 CRANK AND TOGGLE SET The set consists of slider crank with weight hangers, weights and pulley. The experiment is to demonstrate crank moment and slider resistance at different crank angles.

MM 500-121 DEFLECTION OF BEAMS AND CANTILEVERS SET

The set consists of beams of different material, a dial indicator, a vernier caliper, steel rule, fixing attachments, weight hanger and weights. The experiments include relation of beam deflection beam length material (modulus of elasticity), moment of inertia and end condition.

MM 340 STATIC AND DYNAMIC BALANCING MACHINE A motor with speed controller for two-planebalancing. The machine is equipped withstandard rotors, balancing weights, vibrationpickups, signal amplifier and converter andsoftware for data analysis on computer.

MM 343 STATIC AND DYNAMIC BALANCING APPARATUS

Four balance masses. Static balancing by applying known weight steel balls. Dynamic balancing when shaft assembly is driven by a motor. Optional: Inverter for speed control.

MM 440 GYROSCOPE, Two motors Rotor motor and procession motor with speed controllers for a study of gyroscope torque vs precession speeds.

MM 445 CENTRIFUGAL FORCE APPARATUS

Variable rotating masses with adjustable radius, speed and force display.

MM 441 GYROSCOPE, Single Motor A rotor with adjustable mass and radius and a portable tachometer.

MM 450 GOVERNOR APPARATUS Studying motion of Porter, Proell and Hartnell governors.

MM 431 SLIPPING FRICTION APPARATUS A round bar is placed on two counter turning pulleys driven by a variable speed motor with gear reducer. The distance between the two pulleys is adjustable. Measuring instruments for pulley speed and oscillation period are provided.

MM 320 UNIVERSAL VIBRATION APPARATUS The apparatus allows a wide range of vibration studies,

namely: pendulums, mass-spring, free and forced vibration, lateral vibration, torsional vibration, with and without damping. Optional sensors with signal converter and software for data analysis by computer. The set consist of the Basic Units where various accessories and measuring devices are installed for various experiments in vibration.

MM 500-001 BASIC PANEL The perforated panel can be tilted, put in portrait or landscape position. Specific experiments are mounted on the panel by quick fitting screws. Panel size: 375 x 500 mm.

A wide variety of machine elements and mechanism with over 20 sets and more than 60 experiments. Each set is supplied in compact plastic box.

24

MACHINE ELEMENTS AND THEORY OF MACHINES

This group of equipment includes simple equipments for force study, mechanism for a study of machine motion and equipment for more

advanced force and motion study.

MECHANISM FOR MOTION STUDY

FORCE AND MOTION STUDY

MM 211H SLIDER CRANK For demonstration of relative motion between crank rotation and slider translation as found in internal combustion engines.

MM 212H FOUR BAR LINKAGE For demonstration of relative motion between crank rotation and another link oscillation (swinging).

MM 213H SLOTTED LINK For demonstration of relative motion between crank rotation and slider translation through another oscillating link resulting in quick return for slider motion.

MM 214H WHITWORTH QUICK RETURN For demonstration of relative motion between crank rotation and slider translation through another offset rotating member resulting in quick return for slider motion. MM 216H OLDHAM COUPLING For demonstration of relative angular motion between two shafts with parallel but displaced axes.

MM 215H SCOTCH YOKE For demonstration of relative motion between crank rotation and a yoke translation.

MM 219H GENEVA STOP For demonstration of relative angular motion between two parallel shafts – one with continuous rotation, the other with intermittent rotation.

MM 220H CAM AND FOLLOWER For demonstration of relative motion between a rotating eccentric member (cam) and sliding member (follower) translation as found in internal combustion engines.

MM 221 EPICYCLE GEAR TRAIN For demonstration of relative angular motion between two shafts with common axis using sun and planetary gears to produce a forward speed.

MM 222 DOUBLE EPICYCLIC GEAR TRAIN For demonstration of relative angular motion between three shafts with common axis using two epicyclic trains to produce two forward speeds or a forward and a reverse.

MM 223 TRIPLE EPICYCLIC GEAR TRAIN

For demonstration of relative angular motion between four shafts with common axis using three epicyclic trains to produce two forward speeds and a reverse.

MM 312 TORSIONAL OSCILLATIONS APPARATUS

This mechanism demonstrates torsional oscillations of single or multi-rotor and /or geared systems with low natural frequencies.

MM 240 SIMPLE GEARED SYSTEM For determination of system inertia. A system of 12 gears and 4 shafts. Complete with load hanger, weights, measuring tape, stop watch and cord.

MM 242 COMPREHENSIVE GEARED SYSTEM For determination of system inertia and efficiency. Three shafts with fixed and sliding gears, motor dynamometer, inverter, mechanical brake dynamometer, sensors with digital display, weight hanger, weights

and masses.

MM 246 AUTOMOTIVE GEAR SYSTEM EFFICIENCY, Manual Transmission

A bench top unit with five-speed automotive manual gear box, input motor dynamometer, inverter, output dynamometer and measuring instruments for a study of gear efficiency at different loads, speeds and gear ratios. MM 245 AUTOMOTIVE GEAR SYSTEM, Manual Transmission Similar to MM246 with floor standing design and accessories for studying of equivalent gear inertia.

MM 500 MECHANICAL ENGINEERING TEST SETS

MM 500-111 FORCES SET The set consists of plastic plates, angular scale, pulleys, weight hangers and weights, cords and rings, and protactor. The experiments include center of gravity, force triangle, force polygon, Bow’s notation, and non-concurrent forces.

MM 500-112 MOMENTS SET The set consists of riqid beam, crank lever with hook points, spring balances, pulley, weight hangers and weights, cord and hooks. The experiments include principles of moments, beam balances, levers and beam reactions.

MM 500-115 SHEAR AND BENDING MOMENT SET

The apparatus consists of two-part beams and spring attachments, beam supports, spring balances, weight hangers and weights. The experiments include determination of shear force and bending moment on a beam under loads. MM 500-114 SHEAR FORCE SET MM 500-113 BENDING MOMENT SET

MM 500-117 CRANK AND TOGGLE SET The set consists of slider crank with weight hangers, weights and pulley. The experiment is to demonstrate crank moment and slider resistance at different crank angles.

MM 500-121 DEFLECTION OF BEAMS AND CANTILEVERS SET

The set consists of beams of different material, a dial indicator, a vernier caliper, steel rule, fixing attachments, weight hanger and weights. The experiments include relation of beam deflection beam length material (modulus of elasticity), moment of inertia and end condition.

MM 340 STATIC AND DYNAMIC BALANCING MACHINE A motor with speed controller for two-planebalancing. The machine is equipped withstandard rotors, balancing weights, vibrationpickups, signal amplifier and converter andsoftware for data analysis on computer.

MM 343 STATIC AND DYNAMIC BALANCING APPARATUS

Four balance masses. Static balancing by applying known weight steel balls. Dynamic balancing when shaft assembly is driven by a motor. Optional: Inverter for speed control.

MM 440 GYROSCOPE, Two motors Rotor motor and procession motor with speed controllers for a study of gyroscope torque vs precession speeds.

MM 445 CENTRIFUGAL FORCE APPARATUS

Variable rotating masses with adjustable radius, speed and force display.

MM 441 GYROSCOPE, Single Motor A rotor with adjustable mass and radius and a portable tachometer.

MM 450 GOVERNOR APPARATUS Studying motion of Porter, Proell and Hartnell governors.

MM 431 SLIPPING FRICTION APPARATUS A round bar is placed on two counter turning pulleys driven by a variable speed motor with gear reducer. The distance between the two pulleys is adjustable. Measuring instruments for pulley speed and oscillation period are provided.

MM 320 UNIVERSAL VIBRATION APPARATUS The apparatus allows a wide range of vibration studies,

namely: pendulums, mass-spring, free and forced vibration, lateral vibration, torsional vibration, with and without damping. Optional sensors with signal converter and software for data analysis by computer. The set consist of the Basic Units where various accessories and measuring devices are installed for various experiments in vibration.

MM 500-001 BASIC PANEL The perforated panel can be tilted, put in portrait or landscape position. Specific experiments are mounted on the panel by quick fitting screws. Panel size: 375 x 500 mm.

A wide variety of machine elements and mechanism with over 20 sets and more than 60 experiments. Each set is supplied in compact plastic box.

25

MACHINE ELEMENTS AND THEORY OF MACHINES

MM 500-132 TENSILE TEST SET The set consists of a tensile test frame, specimens of different material, a dial indicator, and vernier caliper. The experiments include tensile test to destruction of different material for observation of elastic and plastic regions, modulus of elasticity and ultimate strength.

MM 500-133 TORSION SET The set consists of rods and tubes of different materials, fixed and rotating chucks with pulley, dial indicator, vernier caliper, steel rule, weight hanger and weights. The experiments include relation of angle of twist, specimen length moment of inertia and material.

MM 500-134 SPRING TEST SET The set consists of different size coiled springs, compression test frame, vernier caliper, steel rule, weight hanger and weights. The experiments include spring compression test, spring extension test and series and parallel spring tests.

MM 500-135 POTENTIAL AND KINETIC ENERGY SET The set consists of a ball pendulum with cord, flywheel, spring, weight hanger and weights and stop watch. The experiments includes kinetic and potential energy in a pendulum, potential energy in spring and kinetic energy of flywheel.

MM 500-162 CENTRIFUGAL FORCE SET The set consists of centrifugal force frame, weight hanger, weights and stop watch. The experiments include relationship of centrifugal force with radius, speed and mass.

MM 500-171 BAR LINKAGES SET The set consists perforated bars with different lengths, bar joints, screw driver and spanner, pen and pen holder. The experiments include join and form various linkages for experiments on four bar linkages pantograph, straight line linkages, Ackerman steering.

MM 500-174 ROTARY MOTION FOR TWO SHAFTS SET The set consists of an Oldham coupling and universal joint. The experiments include relative motion of the two shafts for parallel and intersecting shafts.

MM 500-172 CAM AND FOLLOWER SET The set consists of cams of different shapes and flat face and roller followers, angular and linear scales. The experiments include relation between angular and linear displacement of cams and followers.

MM 500-175 INTERMITTENT MOTION SET The set consists of Geneva stop ratchet to demonstrate how a rotary motion is converted to a start-stop motion.

MM 500-173 ROTARY-TRANSLATION MOTION SET

The set consists of a slider crank slotted link, quick return mechanism. The experiments demonstrate the relation between a rotary motion and a translation motion for different mechanism.

MM 500-141 INCLINED PLANE SET The set consists of inclined plane, sliding block, roller set, different surface material, weight hanger and weights. The experiments include forces on inclined plane, rolling and sliding friction on different surfaces static and kinetic sliding friction for different surfaces and angles.

MM 500-142 ROTATIONAL FRICTION SET

MM 500-151 PULLEY SET The set consists of single, double and triple pulleys, Weston differential pulley, wheel and axle, weight hangers and weights. The experiments include simple pulley system wheel and axle and Weston differential pulley.

MM 500-152 BELT AND CHAIN DRIVE SET

MM 500-153 GEAR TRAINS SET The set consists of spur gears of different number of teeth, worm and wheel, bevel gears, weight hangers and weights. The experiments include spur gears gear trains idler gear worm and wheel and bevel gears.

The set consists of screw jack, different bearings, different wedges, weight hanger and weights. The experiments include efficiencies of screw jack, wedges and different bearings.

The set consists of chain drive system, belt drive system weight hangers and weights. The experiments include power transfer and efficiency in belt drive and chain drive and friction and angle of lap on a pulley.

MM 500-161 SIMPLE HARMONIC MOTION SET

The set consists of different pendulums with support, spring mass system, load hanger and weights. The experiments include simple harmonic motion of simple, bifilar and trifilar pendulums, spring mass system, compound and Kater’s pendulums.

This group of equipments requires a main frame where test accessories are attached for experiments. Supporting accessories are used for

installation and/or measurement. Learning software is available for most experiments.

MAIN FRAME

ACCESSORIES FOR STRUCTURAL

ST 300 UNIVERSAL STRUCTURAL FRAME Twin aluminium profile frame on steel support with 850x550 mm. window for attachment of structural models and accessories. Load capacity: 2.5 kN.

ST 305 UNIVERSAL BASE FRAME Bench top base frame of 30x30 mm aluminium profile 950 mm long for attachment of structural models and accessories. It is intended to replace ST 300 UNIVERSAL STRUCTURAL FRAME for many experiments

ST 311 BENDING MOMENT For measurement of bending moment at a section in a beam

ST 312 SHEAR FORCE For measurement of shear force at a section in a beam

ST 3112 SHEAR FORCE AND BENDING MOMENT

For measurement of both shear force and bending moment in the same beam.

ST 316 UNSYMMETRICAL CANTILEVER For studying a cantilever deflection and determining shear center

ST 321 CONTINUOUS BEAM For measurement of reactions for a two- span continuous beam with and without settlement of a support

ST 322 AREA MOMENT METHOD For verification of the deflections and slopes of a beam by area-moment method.

ST 311C BENDING MOMENT, Computer Assist

ST 312C SHEAR FORCE, Computer Assist

ST 3112C SHEAR FORCE AND BENDING MOMENT, Computer Assist

ST 316C UNSYMMETRICAL CANTILEVER, Computer Assist

ST 321C CONTINUOUS BEAM, Computer Assist

ST 322C AREA MOMENT METHOD, Computer Assist

26

MACHINE ELEMENTS AND THEORY OF MACHINES

MM 500-132 TENSILE TEST SET The set consists of a tensile test frame, specimens of different material, a dial indicator, and vernier caliper. The experiments include tensile test to destruction of different material for observation of elastic and plastic regions, modulus of elasticity and ultimate strength.

MM 500-133 TORSION SET The set consists of rods and tubes of different materials, fixed and rotating chucks with pulley, dial indicator, vernier caliper, steel rule, weight hanger and weights. The experiments include relation of angle of twist, specimen length moment of inertia and material.

MM 500-134 SPRING TEST SET The set consists of different size coiled springs, compression test frame, vernier caliper, steel rule, weight hanger and weights. The experiments include spring compression test, spring extension test and series and parallel spring tests.

MM 500-135 POTENTIAL AND KINETIC ENERGY SET The set consists of a ball pendulum with cord, flywheel, spring, weight hanger and weights and stop watch. The experiments includes kinetic and potential energy in a pendulum, potential energy in spring and kinetic energy of flywheel.

MM 500-162 CENTRIFUGAL FORCE SET The set consists of centrifugal force frame, weight hanger, weights and stop watch. The experiments include relationship of centrifugal force with radius, speed and mass.

MM 500-171 BAR LINKAGES SET The set consists perforated bars with different lengths, bar joints, screw driver and spanner, pen and pen holder. The experiments include join and form various linkages for experiments on four bar linkages pantograph, straight line linkages, Ackerman steering.

MM 500-174 ROTARY MOTION FOR TWO SHAFTS SET The set consists of an Oldham coupling and universal joint. The experiments include relative motion of the two shafts for parallel and intersecting shafts.

MM 500-172 CAM AND FOLLOWER SET The set consists of cams of different shapes and flat face and roller followers, angular and linear scales. The experiments include relation between angular and linear displacement of cams and followers.

MM 500-175 INTERMITTENT MOTION SET The set consists of Geneva stop ratchet to demonstrate how a rotary motion is converted to a start-stop motion.

MM 500-173 ROTARY-TRANSLATION MOTION SET

The set consists of a slider crank slotted link, quick return mechanism. The experiments demonstrate the relation between a rotary motion and a translation motion for different mechanism.

MM 500-141 INCLINED PLANE SET The set consists of inclined plane, sliding block, roller set, different surface material, weight hanger and weights. The experiments include forces on inclined plane, rolling and sliding friction on different surfaces static and kinetic sliding friction for different surfaces and angles.

MM 500-142 ROTATIONAL FRICTION SET

MM 500-151 PULLEY SET The set consists of single, double and triple pulleys, Weston differential pulley, wheel and axle, weight hangers and weights. The experiments include simple pulley system wheel and axle and Weston differential pulley.

MM 500-152 BELT AND CHAIN DRIVE SET

MM 500-153 GEAR TRAINS SET The set consists of spur gears of different number of teeth, worm and wheel, bevel gears, weight hangers and weights. The experiments include spur gears gear trains idler gear worm and wheel and bevel gears.

The set consists of screw jack, different bearings, different wedges, weight hanger and weights. The experiments include efficiencies of screw jack, wedges and different bearings.

The set consists of chain drive system, belt drive system weight hangers and weights. The experiments include power transfer and efficiency in belt drive and chain drive and friction and angle of lap on a pulley.

MM 500-161 SIMPLE HARMONIC MOTION SET

The set consists of different pendulums with support, spring mass system, load hanger and weights. The experiments include simple harmonic motion of simple, bifilar and trifilar pendulums, spring mass system, compound and Kater’s pendulums.

This group of equipments requires a main frame where test accessories are attached for experiments. Supporting accessories are used for

installation and/or measurement. Learning software is available for most experiments.

MAIN FRAME

ACCESSORIES FOR STRUCTURAL

ST 300 UNIVERSAL STRUCTURAL FRAME Twin aluminium profile frame on steel support with 850x550 mm. window for attachment of structural models and accessories. Load capacity: 2.5 kN.

ST 305 UNIVERSAL BASE FRAME Bench top base frame of 30x30 mm aluminium profile 950 mm long for attachment of structural models and accessories. It is intended to replace ST 300 UNIVERSAL STRUCTURAL FRAME for many experiments

ST 311 BENDING MOMENT For measurement of bending moment at a section in a beam

ST 312 SHEAR FORCE For measurement of shear force at a section in a beam

ST 3112 SHEAR FORCE AND BENDING MOMENT

For measurement of both shear force and bending moment in the same beam.

ST 316 UNSYMMETRICAL CANTILEVER For studying a cantilever deflection and determining shear center

ST 321 CONTINUOUS BEAM For measurement of reactions for a two- span continuous beam with and without settlement of a support

ST 322 AREA MOMENT METHOD For verification of the deflections and slopes of a beam by area-moment method.

ST 311C BENDING MOMENT, Computer Assist

ST 312C SHEAR FORCE, Computer Assist

ST 3112C SHEAR FORCE AND BENDING MOMENT, Computer Assist

ST 316C UNSYMMETRICAL CANTILEVER, Computer Assist

ST 321C CONTINUOUS BEAM, Computer Assist

ST 322C AREA MOMENT METHOD, Computer Assist

27

STRUCTURES AND ACCESSORIES

ST 323 DEFLECTION OF BEAMS AND CANTILEVERS

For measurement of deflections and slopes of a beam under bending.

ST 333 THREE HINGED ARCH For measurement of horizontal abutment thrust for symmetrical and unsymmetrical three hinged arch using a combination of concentrated and distributed loading.

ST 340 STRAIN AND STRESS OF MATERIAL For demonstration of strain and stress of material using strain gauges.

ST 351 SIMPLE SUSPENSION BRIDGE For measurement of cable tension resulting from uniformly distributed and point loads on the rigid deck.

ST 326C VIRTUAL WORK, Computer Assist

ST 331C TWO HINGED PARABOLIC ARCH, Computer Assist

ST 342 FORCES IN TRUSS For measurement of deflection and axial forces in pin joint trust members.

ST 332 TWO HINGED PARABOLIC ARCH, Fixed Ends

For measurement of horizontal thrust and end fixing moments of the abutment.

ST 341 REDUNDANT TRUSS For measurement of deflection and axial forces in pin-joint trust members when a redundant member is added.

ST 323C DEFLECTION OF BEAM AND CANTILEVERS, Computer Assist

ST 326 VIRTUAL WORK For studying the principle of virtual work to the derivation of redundant reactions.

ST 331 TWO HINGED PARABOLIC ARCH For direct measurement of the horizontal component of the abutment thrust of a two- hinged parabolic arch by using a simple model.

ST 332C TWO HINGED PARABOLIC ARCH, Fixed Ends, Computer Assist

ST 333C THREE HINGED ARCH, Computer Assist

ST 340C STRAIN AND STRESS OF MATERIAL, Computer Assist

ST 341C REDUNDANT TRUSS, Computer Assist

ST 342C FORCES IN TRUSS, Computer Assist

ST 351C SIMPLE SUSPENSION BRIDGE, Computer Assist

ST 352 SUSPENSION BRIDGE For studying the inter-action between suspension cables and load measuring supports with uniformly distributed and point load on the rigid deck.

ST 360 DEFLECTION AND REACTIONS OF FRAMES

For comparison of experimental and theoretical deflections of a rectangular portal, an open square and “S” frame.

ST 365 DEFLECTION OF CURVED BARS For measurement of horizontal and vertical components of curved bar deflections.

ST 361 BENDING MOMENT IN A FRAME For measurement of strain hence bending member along the vertical and horizontal members of the frame.

ST 352C SUSPENSION BRIDGE, Computer Assist

ST 360C DEFLECTION AND REACTIONS OF FRAMES, Computer Assist

ST 361C BENDING MOMENT IN A FRAME, Computer Assist

ST 365C DEFLECTION OF CURVED BARS, Computer Assist

ST 375 TORSION OF RODS AND TUBES For the investigation of torsion and torsional rigidity in rods, tube and split tube.

ST 376 TORSION AND BENDING The apparatus is used for torsion and bending tests on different materials.

ST 375C TORSION OF RODS AND TUBES, Computer Assist

ST 376C TORSION AND BENDING, Computer Assist

ST 362C PLASTIC BENDING MOMENT IN A FRAME, Computer Assist For studying on the relation between deflection of a portal frame under loads in plastic condition .

SAMPLE SOFTWARE FOR COMPUTER ASSIST

28

STRUCTURES AND ACCESSORIES

ST 323 DEFLECTION OF BEAMS AND CANTILEVERS

For measurement of deflections and slopes of a beam under bending.

ST 333 THREE HINGED ARCH For measurement of horizontal abutment thrust for symmetrical and unsymmetrical three hinged arch using a combination of concentrated and distributed loading.

ST 340 STRAIN AND STRESS OF MATERIAL For demonstration of strain and stress of material using strain gauges.

ST 351 SIMPLE SUSPENSION BRIDGE For measurement of cable tension resulting from uniformly distributed and point loads on the rigid deck.

ST 326C VIRTUAL WORK, Computer Assist

ST 331C TWO HINGED PARABOLIC ARCH, Computer Assist

ST 342 FORCES IN TRUSS For measurement of deflection and axial forces in pin joint trust members.

ST 332 TWO HINGED PARABOLIC ARCH, Fixed Ends

For measurement of horizontal thrust and end fixing moments of the abutment.

ST 341 REDUNDANT TRUSS For measurement of deflection and axial forces in pin-joint trust members when a redundant member is added.

ST 323C DEFLECTION OF BEAM AND CANTILEVERS, Computer Assist

ST 326 VIRTUAL WORK For studying the principle of virtual work to the derivation of redundant reactions.

ST 331 TWO HINGED PARABOLIC ARCH For direct measurement of the horizontal component of the abutment thrust of a two- hinged parabolic arch by using a simple model.

ST 332C TWO HINGED PARABOLIC ARCH, Fixed Ends, Computer Assist

ST 333C THREE HINGED ARCH, Computer Assist

ST 340C STRAIN AND STRESS OF MATERIAL, Computer Assist

ST 341C REDUNDANT TRUSS, Computer Assist

ST 342C FORCES IN TRUSS, Computer Assist

ST 351C SIMPLE SUSPENSION BRIDGE, Computer Assist

ST 352 SUSPENSION BRIDGE For studying the inter-action between suspension cables and load measuring supports with uniformly distributed and point load on the rigid deck.

ST 360 DEFLECTION AND REACTIONS OF FRAMES

For comparison of experimental and theoretical deflections of a rectangular portal, an open square and “S” frame.

ST 365 DEFLECTION OF CURVED BARS For measurement of horizontal and vertical components of curved bar deflections.

ST 361 BENDING MOMENT IN A FRAME For measurement of strain hence bending member along the vertical and horizontal members of the frame.

ST 352C SUSPENSION BRIDGE, Computer Assist

ST 360C DEFLECTION AND REACTIONS OF FRAMES, Computer Assist

ST 361C BENDING MOMENT IN A FRAME, Computer Assist

ST 365C DEFLECTION OF CURVED BARS, Computer Assist

ST 375 TORSION OF RODS AND TUBES For the investigation of torsion and torsional rigidity in rods, tube and split tube.

ST 376 TORSION AND BENDING The apparatus is used for torsion and bending tests on different materials.

ST 375C TORSION OF RODS AND TUBES, Computer Assist

ST 376C TORSION AND BENDING, Computer Assist

ST 362C PLASTIC BENDING MOMENT IN A FRAME, Computer Assist For studying on the relation between deflection of a portal frame under loads in plastic condition .

SAMPLE SOFTWARE FOR COMPUTER ASSIST

29

STRUCTURES AND ACCESSORIES

ST 313 INFLUENCE LINE APPARATUS For investigation of reactions under various conditions of load at all supports along a three span bridge.

ST 315 SHEAR CENTER For determination of the plane of traverse loading without twisting for selected standard sections

ST 317 EQUILIBRIUM OF FORCESFor studying the equilibrium of concurrent and non-concurrent forces in a single plane

ST 318 EQUILIBRIUM OF A RIGID BODY

For measurement of the ground and wall reactions as a weight is moved up a rigid ladder.

ST 319 THREE DIMENSIONAL EQUILIBRIUM

For studying the equilibrium of five concurrent and non-concurrent forces in a three-dimensional system.

ST 320 EQUILIBRIUM OF A BEAM For measurement of support reactions of a simple beam or cantilever in equilibrium under different loads.

ST 345 TENSILE MODULUS OF ELASTICITY For measurement of the modulus of elasticity of materials in the form of rods.

ST 343 STRAIN GAUGES For demonstrates the use of electrical resistance strain gauge in measuring strain of material under stress.

ST 370 COLUMN BUCKLING For studying an elastic strut buckling under load with different end conditions.

ST 373 TENSION COEFFICIENTS For demonstrating the use of tension coefficients in resolving three-dimensional forces.

ST 400 UNIVERSAL TEST FRAME ,300kN For studying loading experiments on steel work or civil engineering structure such as girder, beam, truss etc. where actual 1:1 loading can be made. The structure is to be provided by the user.

ESSOM software is LabviewTM based and is available for most equipments. It is classified as Learning Software for equipment without live

Part 1: Receipt of goods, Installation and commissioning o Receiving and Inspection

o Handling, Installation and Commissioning

o Care and safety guidelines

MANUAL All ESSOM equipment are supplied with Operating Manual. Typical manual contents are:

Part 4: Relevant Information o Appendix: Relevant technical data, key

component data, certificates of calibration,

software manual, care/maintenance and

troubleshooting.

o Warranty

o Others: e.g. About ESSOM, ESSOM others products.

Part 2: Product Information and Theory o Section 1: Description of Product Description of

equipment, typical experiment, technical data and

optional equipment both required and accessory

parts.

o Section 2: Theory

General Theory

Relevant Theory

Part 3: Operation and Experiment Procedure o Introduction

o Experiment Procedures

o Typical Data: Data sheet and Sample data

o Sample Calculation

o Graphs

We Supply Worldwide

LEARNING SOFTWARE The software provides information on equipment description, relevant theory, experiment procedures, typical data, to give required calculations upon entering input data manually and to give hard copy printout.

SAMPLE LEARNING SOFTWARE

OPERATING SOFTWARE There are two levels of the software i.e. Computer Interface and Computer Control.

For Computer Interface, sensors analog outputs are converted to digital by an interface module. The software is programmed for the relevant digital signals to be displayed and analyzed by computer.

For Computer Control, an interface module, software program and motor are used in place of relevant manual adjustment. The software data are displayed, analyzed and controlled by computer.

There are cases where only some relevant live signals are available and some data are entered manually. This is sometimes called Computer Assist.

SAMPLE OPERATING SOFTWARE FOR COMPUTER INTERFACE AND COMUTER CONTROL

signals and operating software for equipment and live signals

30

STRUCTURES AND ACCESSORIES

ST 313 INFLUENCE LINE APPARATUS For investigation of reactions under various conditions of load at all supports along a three span bridge.

ST 315 SHEAR CENTER For determination of the plane of traverse loading without twisting for selected standard sections

ST 317 EQUILIBRIUM OF FORCESFor studying the equilibrium of concurrent and non-concurrent forces in a single plane

ST 318 EQUILIBRIUM OF A RIGID BODY

For measurement of the ground and wall reactions as a weight is moved up a rigid ladder.

ST 319 THREE DIMENSIONAL EQUILIBRIUM

For studying the equilibrium of five concurrent and non-concurrent forces in a three-dimensional system.

ST 320 EQUILIBRIUM OF A BEAM For measurement of support reactions of a simple beam or cantilever in equilibrium under different loads.

ST 345 TENSILE MODULUS OF ELASTICITY For measurement of the modulus of elasticity of materials in the form of rods.

ST 343 STRAIN GAUGES For demonstrates the use of electrical resistance strain gauge in measuring strain of material under stress.

ST 370 COLUMN BUCKLING For studying an elastic strut buckling under load with different end conditions.

ST 373 TENSION COEFFICIENTS For demonstrating the use of tension coefficients in resolving three-dimensional forces.

ST 400 UNIVERSAL TEST FRAME ,300kN For studying loading experiments on steel work or civil engineering structure such as girder, beam, truss etc. where actual 1:1 loading can be made. The structure is to be provided by the user.

ESSOM software is LabviewTM based and is available for most equipments. It is classified as Learning Software for equipment without live

Part 1: Receipt of goods, Installation and commissioning o Receiving and Inspection

o Handling, Installation and Commissioning

o Care and safety guidelines

MANUAL All ESSOM equipment are supplied with Operating Manual. Typical manual contents are:

Part 4: Relevant Information o Appendix: Relevant technical data, key

component data, certificates of calibration,

software manual, care/maintenance and

troubleshooting.

o Warranty

o Others: e.g. About ESSOM, ESSOM others products.

Part 2: Product Information and Theory o Section 1: Description of Product Description of

equipment, typical experiment, technical data and

optional equipment both required and accessory

parts.

o Section 2: Theory

General Theory

Relevant Theory

Part 3: Operation and Experiment Procedure o Introduction

o Experiment Procedures

o Typical Data: Data sheet and Sample data

o Sample Calculation

o Graphs

We Supply Worldwide

LEARNING SOFTWARE The software provides information on equipment description, relevant theory, experiment procedures, typical data, to give required calculations upon entering input data manually and to give hard copy printout.

SAMPLE LEARNING SOFTWARE

OPERATING SOFTWARE There are two levels of the software i.e. Computer Interface and Computer Control.

For Computer Interface, sensors analog outputs are converted to digital by an interface module. The software is programmed for the relevant digital signals to be displayed and analyzed by computer.

For Computer Control, an interface module, software program and motor are used in place of relevant manual adjustment. The software data are displayed, analyzed and controlled by computer.

There are cases where only some relevant live signals are available and some data are entered manually. This is sometimes called Computer Assist.

SAMPLE OPERATING SOFTWARE FOR COMPUTER INTERFACE AND COMUTER CONTROL

signals and operating software for equipment and live signals

31

SOFTWARE AND MANUAL

32