View
4
Download
0
Category
Preview:
Citation preview
Component
1. Body2. Ball
3. Seat (2)
4. O-Ring (2) 5. End Connector (2) 5-1. Insert 6. Ball Valve Stem7. Lower Packing8. Upper Packing9. Grand Washer10. Spring Washer
11. Handle
12. Lock Nut
4. O-Ring is applicable to DK-LOK end connection5. End Connector is for DK-LOK end connection5-1. Insert is for Pipe Thread end connection* TFM 1600 seat is applicable only to body in stainless.
ASTM B16 or JIS H3250
NBR
ASTM B16 or JIS H3250
SS304
Valve Body Materials
Stainless Steel Brass
SS316/ASTM A276 or A479
FKM
SS316/ ASTM A276 or A479
SS304
SS316 / ASTM A276PTFE / D1710 for pressure 68.9 bar (1000 psig)
TFM 1600 for pressure 137 bar (2000 psig)*
SS316/ ASTM A276 or A479PTFE / D1710PTFE / D1710
SS304 /ASTM A276 or A479Stainless Steel
SS304 Lever handle with vinyl sleeveZINC/ ASTM B240 Butterfly handle, Nickel-plated
12
10
7
6
2
98
11
1
34
5
Catalog No. V81-5Sept. 2008
Compact barstock construction for high integrityBlow-out proof design with internally loaded stem Floating Ball design providing seat wear compensationMicro-finished ball ensures a leak-tight shut-off on pressure Standard lever handle, optional butterfly handle.
Valve with lever handle Working pressure
PTFE seats: 68.9 bar (1000 psig) TFM seats: 137 bar (2000 psig)
TFM 1600 SeatBody Material: Stainless
PTFE SeatBody Material: Stainless and Brass
Valve with butterfly handle Working pressure
PTFE seats: 68.9 bar (1000 psig) TFM seats not applicable
V81 series ball valve offers a safe and reliable performance for awide range of onshore and offshore applications: water, oil, gas,petrochemical and general duty applications.
ea
aea
Basic Ordering Number
End ConnectionInlet / Outlet
CvOrifice
mm (in.)Dimensions, mm (in.)
L H
Ball Valves V81 Series
Every valve is factory tested with nitrogen gas @41 bar (600 psig) for leakage at the seat to a maximum allowable leak rate of 0.1 SCCM. Thepacking is tested with nitrogen for no detectable leakage.
Dimensions shown are for reference only, subject to change. Dimensions with DK-LOK nuts are in finger-tight position
Safe Valve SelectionThe selection of a valve for any application or system design must be considered to ensure safe performance.Valve function, valve rating, material compatibility, proper installation, operation and maintenance remain the sole responsibillty of the system designerand the user. Dk Tech accepts no liability for any improper selection, installation, operation or maintenance.
Select valve ordering number, applicable option(s) from designator tables listed below.Examples
V81A-D-6M- TF- S
V81A-D-6M- VT- BF- B
V81A-
V81B-
V81C-
V81D-
V81E-
D-6MD-4TF-4ND-10MD-6TF-6ND-12MD-8TF-8ND-16MD-10TF-12ND-12TD-16TF-16N
6mm DK-LOK1/4 in. DK-LOK1/4 in. Female NPT10mm DK-LOK3/8 in. DK-LOK3/8 in. Female NPT12mm DK-LOK1/2 in. DK-LOK1/2 in. Female NPT16mm DK-LOK5/8 in. DK-LOK3/4 in. Female NPT3/4 in. DK-LOK1 in. DK-LOK1 in. Female NPT
1.251.251.352.62.52.69.259.259.2510.610.612.6512.6517.3517.35
79 (3.11)79 (3.11)
41.9 (1.65)90 (3.54)90 (3.54)45 (1.77)98 (3.86)98 (3.86)
56.15 (2.21)108 (4.25)108 (4.25)60 (2.36)109 (4.29)133 (5.23)78.1 (3.07)
5(0.20)
7.50 (0.30)
9.00 (0.35)
12.50 (0.49)
16.00 (0.63)
31 (1.22)
40(1.57)
42 (1.65)
51(2.00)
55(2.16)
hex
17(11/16)
20.64(13/16)
27(1-1/16)
32 (1-1/4)
38 (1-1/2)
A
59.5 (2.34)
81 (3.19)
81 (3.19)
102.5 (4.04)
102.5 (4.04)
A1
30.50 (1.20)
42.00 (1.65)
46.00 (1.81)
49.50 (1.95)
68.00 (2.68)
H1
23.50 (0.93)
30.00 (1.18)
35.70 (1.41)
38.10 (1.50)
45.00 (1.77)
Seat Material O-ring Handle Body material
Nil: Standard PTFE seats for 68.9 bar(1000 psig) working pressure.
TF: Optional TFM1600 for 137 bar (2000 psig) working pressure.
NOTE:TFM1600 seat is not applicable to Brassvalve.
Nil: Standard lever handle BF: Optional butterfly handle
NOTE: BF option is not applicable to the valvewith TF seats.
Nil: FKM O-ring is standard for SS316 body.
Nil: NBR O-ring is standard for Brass body.
VT: FKM O-ring for Brass body BN: NBR O-ring for SS316
NOTE:O-ring is required for DK-LOK endconnection.
S: S316B: Brass
Catalog No. V82-3April 2008
V82 Series Ball ValvesPressure Rating up to 3000psig
Features of V82 Series
Operation & Packing Adjustment
Materials of Construction
Sealing is achieved without system pressure Bi-directional flowPressure up to 3000 psig (206 bar) Lowest dead space design
Nylon Directional handle - indicates the flow through the valve. Panel mounting nut - is standard and permits valve to panel or actuator.Top-loaded packing - allows packing adjustment with the valve in-line.Capsule packing - fills voids in the valve body and prevents fluid entrapment.
- allows lowest dead space.Support rings and discs - retains the capsule packing and prevent cold flow.Integral ball stem - machined from single piece bar stock.
- eliminates the backlash during handle actuation. One-piece body - reduces the number of potential leak points.
V82 valves are designed to control fluid in full open and closed position; using V82 valves to throttle the flow may reduce the valve life. Valves that have not been actuated for a period of time may have a higher initial actuation torque. Every valve working pressure is adjusted for factory test at 1000 psig (68.9 bar) @ 21°C (70°F). For use in higher pressure, the valve packing may be required for re-adjustment. Packing adjustment may be required during the valve in service.
ApplicationAnalytical market requiring a valve with lowest dead volume to prevent fluid entrapment which can cause contamination. Control Sampling Systems, and Process Instrumentation market requiring a valve with compact size, high flow capacity and directional indication of flow.
Factory Test and Packaging Every valve is factory tested with nitrogen gas at 1000 psig (68.9 bar) for leakage at seat to a maximum allowable leak rate of 0.1 SCCM.The packing is tested with nitrogen gas for no detectable leakage. Every valve is cleaned and packaged in accordance with DK cleaning standard DC-01
ComponentValve Body Materials
Grade/ASTM Specification
Nylon with brass insert
17-4PH/A564
SS316/A276 or A479
17-4PH/A693
PTFE/D1710 type 1, Grade 1, Class B
SS316/A276
PTFE/D1710 type 1
SS316/A276
SS316 powered metal/B783
(fluorocarbon coating)
1. Handle
2. Set Screw
3. Packing bolt
4. Upper Gland
4a. Packing Spring (VL82 series)
5. Bushing
6. Lower gland
6a. Packing Gland (VL82 series)
7 & 11. Upper & Lower Packing
8. Ball stem
9. Support rings
10. Side discs
12. Panel nut
13. Body
Stainless Steel Brass
SS316/A276 or A479 Brass B16
SS316/A276 Brass B16
SS316/A276
SS316/A276 or A479Brass B16
Molybdenum disulfide with hydrocarbon coating.Note: 1. Wetted parts and lubricants are listed in blue.
2. Lubricant is Fluorinated-based. Lubricants are available for a specific application.
Ballll Vallvess V82 Series
Copyright 2001, 2008 Dk Tech Corporation, All Rights Reserved. 2
2-way On-off Valves
Ordering Information and Table of Dimensions
Technical Data for V82 series with standard PTFE seat Technical Data for VL82 series with PTFE seatValve Series
In-LinepatternV82A
V82B
V82C, V82D
-
psig
2500
3000
2500
1500
bar
172
206
172
103
V82A-A, V82B-A
-
-
V82C-A, V82D-A
Anglepattern
Pressure Rating
PTFE seat
10°C to 65°C(50°F to 150°F)
Temp. Range Valve Series In-line pattern
Pressure Rating
VL82A seriesVL82B series
TemperatureRating
-54 °C to 65 °C(-65 °F to 150 °F)
25003000
psig
172206
bar
To improve thermal cycle performance VL82 series has packing springs inthe place of V82 series upper gland & bushing.
All dimensions shown are for reference only and are subject to change. Dimensions with Dk-Lok nuts are in finger-tight position. Patterns: To order angle pattern, use -A as a suffix to the basic ordering number. Example: V82B-D-4T-A-STop mounting: To order Top mounting option, use -TM as a suffix to the basic ordering number. Example: V82C-D-6T-TM-S
BasicOrderingNumber
OrificeInlet Outlet
End Connections
D1T-
D2T-
D3M-
D4T-
D6M-
F2N-
D4T-
D6T-
D6M-
D8M-
F2N-
F4N-
M4N-
F4R-
D6T-
D10M
F4N-
F6N-
F6R-
D8T-
D12T-
D12M-
F8N-
F8R-
1/16" Dk-Lok
1/8" Dk-Lok
3mm Dk-Lok
1/4" Dk-Lok
6mm Dk-Lok
1/8" Female NPT
1/4" DK-Lok
3/8" Dk-Lok
6mm Dk-Lok
8mm Dk-Lok
1/8" Female NPT
1/4" Female NPT
1/4" Male NPT
3/8" Dk-Lok
10mm Dk-Lok
1/4" Female NPT
3/8" Female NPT
1/2" Dk-Lok
3/4" DK-Lok
12mm Dk-Lok
1/2" Female NPT
inch0.052
0.093
0.093
0.125
0.125
0.125
0.187
0.187
0.187
0.187
0.187
0.187
0.187
0.187
0.281
0.281
0.281
0.281
0.281
0.406
0.406
0.375
0.406
0.406
1.3
2.4
2.4
3.2
3.2
3.2
4.8
4.8
4.8
4.8
4.8
4.8
4.8
4.8
7.1
7.1
7.1
7.1
7.1
10.3
10.3
9.5
10.3
10.3
V82A-
V82B-
V82C-
V82D-
1/4" ISO FemaleTapered
3/8" ISO FemaleTapered
1/2" ISO FemaleTapered
mmCv Dimensions mm (inches)
Angle-
0.15
0.15
0.35
0.35
0.3
0.9
0.9
0.9
0.9
0.7
0.75
0.75
-
2.0
2.0
1.7
1.5
-
4.6
3.8
4.6
3.5
-
L42.7(1.68)
51.1(2.01)
51.1(2.01)
56.1(2.21)
56.1(2.21)
41.1(1.62)
59.9(2.36)
65.5(2.58)
60.7(2.39)
62.5(2.46)
50.8(2.00)
52.3(2.06)
50.8(2.00)
52.3(2.06)
77.5(3.05)
78.0(3.07)
63.5(2.50)
63.5(2.50)
63.5(2.50)
99.6(3.92)
99.6(3.92)
99.6(3.92)
79.2(3.12)
79.2(3.12)
L121.3(0.84)
25.7(1.01)
25.7(1.01)
27.9(1.10)
27.9(1.10)
20.6(0.81)
30.0(1.18)
32.8(1.29)
30.5(1.20)
31.2(1.23)
25.4(1.00)
26.2(1.03)
25.4(1.00)
26.2(1.03)
38.6(1.52)
38.9(1.53)
31.8(1.25)
31.8(1.25)
31.8(1.25)
49.8(1.96)
49.8(1.96)
49.8(1.96)
39.6(1.56)
39.6(1.56)
L221.3(0.84)
25.7(1.01)
25.7(1.01)
27.9(1.10)
27.9(1.10)
20.6(0.81)
30.0(1.18)
32.8(1.29)
30.5(1.20)
31.2(1.23)
25.4(1.00)
26.2(1.03)
25.4(1.00)
26.2(1.03)
38.6(1.52)
38.9(1.53)
31.8(1.25)
31.8(1.25)
31.8(1.25)
49.8(1.96)
49.8(1.96)
49.8(1.96)
39.6(1.56)
39.6(1.56)
H3-
24.6(0.97)
24.6(0.97)
27.2(1.07)
27.2(1.07)
20.6(0.81)
29.7(1.17)
32.8(1.29)
29.7(1.17)
30.5(1.20)
25.4(1.00)
26.2(1.03)
26.2(1.03)
-
36.3(1.43)
36.9(1.43)
31.8(1.25)
31.8(1.25)
-
44.2(1.74)
44.2(1.74)
44.2(1.74)
39.6(1.56)
-
H28.6(0.34)
8.6(0.34)
8.6(0.34)
8.6(0.34)
8.6(0.34)
8.6(0.34)
11.2(0.44)
11.2(0.44)
11.2(0.44)
11.2(0.44)
11.2(0.44)
11.2(0.44)
11.2(0.44)
11.2(0.44)
14.2(0.56)
14.2(0.56)
14.2(0.56)
14.2(0.56)
14.2(0.56)
17.5(0.69)
17.5(0.69)
17.5(0.69)
17.5(0.69)
17.5(0.69)
H17.1(0.28)
7.1(0.28)
7.1(0.28)
7.1(0.28)
7.1(0.28)
7.1(0.28)
9.7(0.38)
9.7(0.38)
9.7(0.38)
9.7(0.38)
9.7(0.38)
9.7(0.38)
9.7(0.38)
9.7(0.38)
14.2(0.56)
14.2(0.56)
14.2(0.56)
14.2(0.56)
14.2(0.56)
17.5(0.69)
17.5(0.69)
17.5(0.69)
17.5(0.69)
17.5(0.69)
A28.4(1.12)
28.4(1.12)
28.4(1.12)
28.4(1.12)
28.4(1.12)
28.4(1.12)
38.9(1.53)
38.9(1.53)
38.9(1.53)
38.9(1.53)
38.9(1.53)
38.9(1.53)
38.9(1.53)
38.9(1.53)
50.8(2.00)
50.8(2.00)
50.8(2.00)
50.8(2.00)
50.8(2.00)
76.2(3.00)
76.2(3.00)
76.2(3.00)
76.2(3.00)
76.2(3.00)
T 6.4(1/4)
6.4(1/4)
6.4(1/4)
6.4(1/4)
6.4(1/4)
6.4(1/4)
4.8(3/16)
4.8(3/16)
4.8(3/16)
4.8(3/16)
4.8(3/16)
4.8(3/16)
4.8(3/16)
4.8(3/16)
9.5(3/8)
9.5(3/8)
9.5(3/8)
9.5(3/8)
9.5(3/8)
9.5(3/8)
9.5(3/8)
9.5(3/8)
9.5(3/8)
9.5(3/8)
H34.5(1.36)
34.5(1.36)
34.5(1.36)
34.5(1.36)
34.5(1.36)
34.5(1.36)
39.6(1.56)
39.6(1.56)
39.6(1.56)
39.6(1.56)
39.6(1.56)
39.6(1.56)
39.6(1.56)
39.6(1.56)
52.6(2.07)
52.6(2.07)
52.6(2.07)
52.6(2.07)
52.6(2.07)
61.7(2.43)
61.7(2.43)
61.7(2.43)
61.7(2.43)
61.7(2.43)
W14.7(0.58)
14.7(0.58)
14.7(0.58)
14.7(0.58)
14.7(0.58)
14.7(0.58)
19.8(0.78)
19.8(0.78)
19.8(0.78)
19.8(0.78)
19.8(0.78)
19.8(0.78)
19.8(0.78)
19.8(0.78)
28.4(1.12)
28.4(1.12)
28.4(1.12)
28.4(1.12)
28.4(1.12)
38.1(1.50)
38.1(1.50)
38.1(1.50)
38.1(1.50)
38.1(1.50)
D15.1(19/32)
15.1(19/32)
15.1(19/32)
15.1(19/32)
15.1(19.32)
15.1(19/32)
19.8(25/32)
19.8(25/32)
19.8(25/32)
19.8(25/32)
19.8(25/32)
19.8(25/32)
19.8(25/32)
19.8(25/32)
28.6(1-1/8)
28.6(1-1/8)
28.6(1-1/8)
28.6(1-1/8)
28.6(1-1/8)
38.1(1-1/2)
38.1(1-1/2)
38.1(1-1/2)
38.1(1-1/2)
38.1(1-1/2)
0.1
0.2
0.2
0.6
0.6
0.5
2.4
1.5
2.4
1.5
1.2
0.9
1.2
0.9
6.0
6.0
3.0
2.6
2.6
12.0
6.4
12.0
6.3
6.3
Inline
Ballll Vallvess V82 Series
3
3-way Switching Valves
Ordering Information and Table of Dimensions
Flow Data2-way
All dimensions shown are for reference only and are subject to change. Dimensions with Dk-Lok nuts are in finger-tight position.
Technical Data for valves with standard PTFE seat
Valve SeriesPressure Rating
V82A-3B, V82B-3BV82C-3B, V82D-3B
Temperature Range PTFE seat
10 °C to 65 °C(50 °F to 150 °F)
25001500
psig
172103
bar
Basic OrderingNumber
Orifice Dimensions mm (inches)End Connections
D1T-
D2T-
D4T-
D3M-
D6M-
F2N-
D4T-
D6M-
D8M-
F4N-
F4R-
D6T-
D10M-
F4N-
F6N-
F6R-
D8T-
D12T-
D12M-
F8N-
F8R-
1/16" Dk-Lok
1/8" Dk-Lok
1/4" Dk-Lok
3mm Dk-Lok
6mm Dk-Lok
1/8" Female NPT
1/4" Dk-Lok
6mm Dk-Lok
8mm Dk-Lok
1/4" Female NPT
3/8" Dk-Lok
10mm Dk-Lok
1/4" Female NPT
3/8" Female NPT
1/2" Dk-Lok
3/4" Dk-Lok
12mm Dk-Lok
1/2" Female NPT
inch0.052
0.093
0.125
0.093
0.125
0.125
0.187
0.187
0.187
0.187
0.187
0.281
0.281
0.281
0.281
0.281
0.406
0.406
0.375
0.406
0.406
L42.7(1.68)
51.1(2.01)
56.1(2.21)
51.1(2.01)
56.1(2.21)
41.4(1.63)
60.7(2.39)
60.7(2.39)
62.5(2.46)
52.3(2.06)
52.3(2.06)
73.4(2.89)
73.4(2.89)
63.5(2.50)
63.5(2.50)
63.5(2.50)
88.4(3.48)
88.4(3.48)
88.4(3.48)
79.5(3.13)
79.5(3.13)
L121.3(0.84)
25.7(1.01)
27.9(1.10)
25.7(1.01)
27.9(1.10)
20.6(0.81)
30.5(1.20)
30.5(1.20)
31.2(1.23)
26.2(1.03)
26.2(1.03)
36.8(1.45)
36.8(1.45)
31.8(1.25)
31.8(1.25)
31.8(1.25)
44.2(1.74)
44.2(1.74)
44.2(1.74)
39.6(1.56)
39.6(1.56)
H120.6(0.81)
24.6(0.97)
27.2(1.07)
24.6(0.97)
27.2(1.07)
20.6(0.81)
29.7(1.17)
29.7(1.17)
30.5(1.20)
26.2(1.03)
26.2(1.03)
36.3(1.43)
36.3(1.43)
31.8(1.25)
31.8(1.25)
31.8(1.25)
44.2(1.74)
44.2(1.74)
44.2(1.74)
39.6(1.56)
39.6(1.56)
H28.6(0.34)
8.6(0.34)
8.6(0.34)
8.6(0.34)
8.6(0.34)
8.6(0.34)
11.2(0.44)
11.2(0.44)
11.2(0.44)
11.2(0.44)
11.2(0.44)
14.2(0.56)
14.2(0.56)
14.2(0.56)
14.2(0.56)
14.2(0.56)
17.5(0.69)
17.5(0.69)
17.5(0.69)
17.5(0.69)
17.5(0.69)
A28.7(1.13)
28.7(1.13)
28.7(1.13)
28.7(1.13)
28.7(1.13)
28.7(1.13)
38.9(1.53)
38.9(1.53)
38.9(1.53)
38.9(1.53)
38.9(1.53)
50.8(2.00)
50.8(2.00)
50.8(2.00)
50.8(2.00)
50.8(2.00)
76.2(3.00)
76.2(3.00)
76.2(3.00)
76.2(3.00)
76.2(3.00)
T 6.4(1/4)
6.4(1/4)
6.4(1/4)
6.4(1/4)
6.4(1/4)
6.4(1/4)
4.8(3/16)
4.8(3/16)
4.8(3/16)
4.8(3/16)
4.8(3/16)
9.7(3/8)
9.7(3/8)
9.7(3/8)
9.7(3/8)
9.7(3/8)
9.7(3/8)
9.7(3/8)
9.7(3/8)
9.7(3/8)
9.7(3/8)
D15.0(19/32)
15.0(19/32)
15.0(19/32)
15.0(19/32)
15.0(19/32)
15.0(19/32)
19.8(25/32)
19.8(25/32)
19.8(25/32)
19.8(25/32)
19.8(25/32)
28.7(1-1/8)
28.7(1-1/8)
28.7(1-1/8)
28.7(1-1/8)
28.7(1-1/8)
38.1(1-1/2)
38.1(1-1/2)
38.1(1-1/2)
38.1(1-1/2)
38.1(1-1/2)
H34.5(1.36)
34.5(1.36)
34.5(1.36)
34.5(1.36)
34.5(1.36)
34.5(1.36)
39.6(1.56)
39.6(1.56)
39.6(1.56)
39.6(1.56)
39.6(1.56)
52.6(2.07)
52.6(2.07)
52.6(2.07)
52.6(2.07)
52.6(2.07)
61.7(2.43)
61.7(2.43)
61.7(2.43)
61.7(2.43)
61.7(2.43)
W14.7(0.58)
14.7(0.58)
14.7(0.58)
14.7(0.58)
14.7(0.58)
14.7(0.58)
19.8(0.78)
19.8(0.78)
19.8(0.78)
19.8(0.78)
19.8(0.78)
28.4(1.12)
28.4(1.12)
28.4(1.12)
28.4(1.12)
28.4(1.12)
38.1(1.50)
38.1(1.50)
38.1(1.50)
38.1(1.50)
38.1(1.50)
Cv
0.08
0.15
0.35
0.15
0.35
0.3
0.90
0.90
0.80
0.75
0.75
2.0
2.0
1.7
1.5
1.5
4.6
3.8
4.6
3.5
3.5
1.3
2.4
3.2
2.4
3.2
3.2
4.8
4.8
4.8
4.8
4.8
7.1
7.1
7.1
7.1
7.1
10.3
10.3
9.5
10.3
10.3
0.1 0.2 0.5 0.6 0.9 1.2 1.5 2.4 2.6 3.0 6.0 6.3 6.4 12.0
10(0.7)0.3(1.1)0.6(2.3)1.6 (5.7) 1.9 (7.2) 2.8 (10.6) 3.8 (14.0)4.7 (17.8)7.6 (28.4)8.2 (31.0) 9.5 (35.6) 19.0 (71.9)19.9 (75.5) 20.2 (75.7) 37.9 (143.8)
50 (3.5)0.7 (2.6) 1.4 (5.3) 3.5 (13.2)4.2 (15.9) 6.4 (23.8) 8.5 (31.8) 11.0 (41.6) 17.0 (64.3) 18.0 (68.1) 21.2 (79.5) 42.0 (159.0) 44.5 (170.3) 45.3 (170.3) 84.9 (321.7)
100 (7.0)1.0 (3.8)2.0 (7.6) 5.0 (18.9) 6.0 (22.7) 9.0 (34.0) 12.0 (45.4) 15.0 (56.8) 24.0 (90.8) 26.0 (98.4) 30.0 (113.6)60.0 (227.1) 63.0 (237.0)64.0 (242.2)120.0 (454.2)
10 (0.7)1.1 (31) 2.3 (76)5.6 (195) 6.8 (235) 10.0 (340) 14.0 (481) 17.0 (595) 27.0 (935) 29.0 (1020) 34.0 (1189)68.0 (2351) 71.0 (2464) 72.0 (2520) 130.0 (4814)
50 (3.5)3.0 (85)6.0 (215) 15.0 (538) 18.0 (651) 27.0 (963) 36.0 (1303) 45.0 (1614)72.0 (2606) 78.0 (2804)90.0 (3115)180.0 (6514) 190.0 (6797) 190.0 (6797) 360.0 (13027)
100 (7.0)5.3 (150) 11.0 (396) 27.0 (963) 32.0 (1161) 48.0 (1720) 64.0 (2294) 80.0 (2832) 120.0 (4531) 140.0 (5098) 160.0 (5664) 320.0 (11611) 340.0 (12178) 340.0 (12178) 640.0 (22939)
V823A-
V823B-
V823C-
V823D-
Cv
Water US GPM(L/min).
@21°C (70°F)Pressure Drop to Atmosphere (Δp) psi (bar)
Air SCFM(NL/min.)
@21°C (70°F)
2-way angle pattern and 3-way
0.08 0.15 0.30 0.35 0.75 0.80 0.90 1.5 1.7 2.0 3.5 3.8 4.6
10 (0.7)0.3 (1.1)0.4 (1.5) 0.9 (3.4) 1.1 (4.2) 2.3 (8,7) 2.5 (9.5) 2.8 (10.6) 4.7 (17.8) 5.3 (20.1) 6.3 (23.8) 11.0 (41.6) 12.0 (45.4) 15.0 (56.8)
50 (3.5)0.6 (2.3) 1.0 (3.8) 2.1 (7.9) 2.4 (9.1) 5.3 (20.1) 5.6 (21.2) 6.3 (23.8) 11.0 (41.6) 12.0 (45.4) 14.0 (53.0) 25.0 (94.6) 27.0 (102.2) 33.0 (124.9)
100 (7.0)0.8 (3.0) 1.5 (5.7) 3.0 (11.4) 3.5 (13.2) 7.5 (28.4) 8.0 (30.3) 9.0 (34.1)15.0 (56.8) 17.0 (64.3) 20.0 (75.7) 35.0 (132.5) 38.0 (143.8) 46.0 (174.1)
10 (0.7)0.9 (26) 1.7 (57) 3.4 (116) 4.0 (136) 8.5 (283) 9.0 (312) 10.0 (340) 17.0 (595) 19.0 (680) 22.0 (793) 39.0 (1359) 43.0 (1501) 52.0 (1812)
50 (3.5)2.4 (68) 4.5 (161) 9.0 (312) 10.0 (368) 22.0 (821) 24.0 (878) 27.0 (963) 45.0 (1614) 51.0 (1841) 60.0 (2181)100.0 (3682) 110.0 (3965) 140.0 (5098)
100 (7.0)4.3 (122) 8.0 (286) 16.0 (566) 19.0 (680) 40.0 (1444) 42.0 (1529) 48.0 (1728) 80.0 (2832) 90.0 (3115)100.0 (3965) 180.0 (6797) 200.0 (7363) 240.0 (8779)
Cv
Water US GPM(L/min.)
@21°C (70°F)Pressure Drop to Atmosphere (Δp) psi (bar)
Air SCFM(NL/min.)
@21°C (70°F)
1/4" ISO FemaleTapered
3/8" ISO FemaleTapered
1/2" ISO FemaleTapered
mm
Ballll Vallvess V825 / V824 Series
ea
aea
How to OrderSelect applicable valve pattern, options and body material from designators listed below.V824A-F2N -AH -BV82B-D4T -A -NL -S
Technical Data with standard PTFE seat
Features
Ordering Information and Table of Dimensions
Handle Options
V825 Switching 5-way Ball Valves
Flow switches from a single port to multiple ports or from multiple ports to a single port. Spring-loaded detent ensures exact port positioning.
ValveSeries
Pressure Rating @ 37 °C (100 °F)
V825AV825B
TemperatureRange
10 to 65 °C50 to 150 °F
bar172103
psig25001500
Ordering Number EndConnection Cv
Orifice Dimensions, mm(in.)
V825A-F2N-SF2G-S
1/8 in. Female NPT1/8 in. ISO Parallel Threads
3.5
0.07
10.3
1.6
mm39.4
(1.94)
79.5 (3.13)
L
39.6 (1.56)
19.8 (0.78)
L1
39.6 (1.56)
22.4 (0.88)
H1
17.5 (0.69)
11.2 (0.44)
H2
76.2 (3.00)
38.9 (1.53)
A
9.7 (3/8)
4.1 (5/32)
T*
38.1 (1 1/2)
23.1 (29/32)
D
61.7 (2.43)
42.9 (1.69)
H
V825B- F8N-S 1/2 in. Female NPT 0.406
0.062
inch
T* indicates the maximum panel thickness. 3.2 mm (1/8 in.) minimum panel thickness. D : Panel hole
Aluminum BarAdd-AH to the valve ordering number.Example:V824A-F-2N-AH-S
2-way Top mountingA: 2-way angle pattern TM: top mounting
Valve with no lubricantNL: No lubricant Valve
Bar handle Body material
Note: Top mounting option is applicableonly to the in-line pattern 2-wayvalves.
Note: Valve with no lubricant is factory tested at 200 psig(13 bar). This valve has a pressure rating of 200 psig(13 bar).
Nil: Standard Nylon handleAH: Aluminum bar handleBH: Stainless bar handle
S: SS316B: Brass
Safe Valve SelectionThe selection of a valve for any application or system design must be considered to ensure safe performance.Valve function, valve rating, material compatibility, proper installation, operation and maintenance remain the sole responsibillty of thesystem designer and the user. Dk Tech accepts no liability for any improper selection, installation, operation or maintenance.
Stainless BarAdd-BH to the valve ordering number.Example:V824A-F-2N-BH-S
DT
Features
Ordering Information and Table of Dimensions
V824 Crossover 4-way Ball Valves
T* indicates maximum panel thickness D : Panel Hole
Technical Data with standard PTFE seat
Crossover of two streamsMechanical stop ensures positive port positioning
ValveSeries
Pressure Rating @ 37 °C (100 °F)
V824AV824B
TemperatureRange
10 to 65 °C50 to 150 °F
bar172103
psig25001500
Ordering Number EndConnection Cv
Orifice Dimensions, mm(in.)
V824A-V824B-
1/8 in. Female NPT1/2 in. Female NPT
0.081.6
mm1.67.1
L39.4 (1.55)79.5 (3.13)
L119.8 (0.78)39.6 (1.56)
H111.2 (0.44)17.5 (0.69)
A38.9 (1.53)76.2 (3.00)
T*4.8 (3/16)9.7 (3/8)
D23.1 (29/32)38.1 (1 1/2)
H42.7 (1.68)61.7 (2.43)
inch0.0620.281
F2N-SF8N-S
Catalog No. V83-3Oct. 2009
V83 Series Swing-Out Ball ValvesPressure Rating up to 3000 psig (206 bar)
Pressure and temperature compensation seat design.Swing-out design for fast and easy maintenance with the valve in-line.Chevron packing design. 2-way (on-off) valves with quarter-turn actuation.
Every valve is tested with nitrogen @ 68.9 bar (1000 psig) for leakage at the seat to a maximum allowable leak rate of 0.1 SCCM.Shell test with nitrogen @ 68.9 bar (1000 psig) is performed to a requirement of no detectable leakage with a liquid leak detector. Shell test with water at 1.5 times the working pressure is performed on request with extra cost.
Features
Factory Test
Two flats on stem (10) and lever handle (13) indicate open orclosed position of the valve.
Built-in manual locking device (14) allowslocking the valve with a detent either inopen or closed position. You may alsoapply a pad-lock to this device. Pad-lockhole: 8 mm (0.314 in.)
Compensation seat design requiresno pressure to create a seal. Under high pressure, seats reacton the ball movement for sealingat upstream and downstream.
13
98 215 34
10
67
1411
11
1920
1215
1617
18
Seat
Ball
SeatSupport Ring
DiscSpring
Flange Seals
Table 1. Material of Construction
Component
1. Body2. Flanges (2)3. Ball 4. Seats (2)5. Flanage Seals (2) 6. Disc Spring (2) 7. Seat support rings (2)8. Body fasteners (4)9. Body hex nuts (4) 10. Stem11. Stem Nuts (2) 12. Tooth Washer13. Handle 14. Locking Device15. Grounding spring16. Stem Springs (2)17. Gland18. Packing Support19. Upper & Lower Packing20. Stem Bearing
Valve Body Materials Stainless steel Carbon Steel
Grade / ASTM SpecificationCF8M / A351 A216 WCBCF8M / A351 A216 WCB
Type 316 / A276See Table 2.
PTFE, Optional FKM O-ringType 631
Type 316 / A276SS316 Gr.B8M/ A193 SS316 Gr.8M/ A194
Type 316 / A276, A479SS316
Stainless steelSS304 with Vinyl sleeve
SS304SS312 / A313
Strain Hardened SS316 / A240Type 316 / A276
PEEK (Polyetheretherketone) Reinforced PTFE
PEEK, Optional X750Wetted parts and lubricants are listed in blue.
Table 2. Seat MaterialsPressure - Temperature Ratings
Seats
StandardReinforced
PTFE
V83AV83BV83CV83AV83BV83CV83AV83BV83C
V83A
V83BV83C
V83A
V83BV83C
VirginPTFE
CarbonPTFE
PEEK
UHMWPE
151 bar(2200 psig)
103 bar(1500 psig)
172 bar(2500 psig)
206 bar(3000 psig)
172 bar(2500 psig)
172 bar(2500 psig)
206 bar(3000 psig)
Valve Series
Pressure Rating@ -28 to 38 C(-20 to 100 F)
7 bar @ 232 C 100 psig @450 F
7 bar @ 232 C 100 psig @450 F
7 bar @ 232 C100 psig @450 F
55 bar @ 232 C 800 psig @ 450 F
17 bar @ 121 C250 psig @ 250 F
Pressure @ Max. Temperature
Silicon based and
PTFE based
PTFE based
Hydrocarbonbased and PTFE based
Lubricants
PRESSURE-TEMPEATURE GRAPH
Swing-Out Ball Valves V83 Series
2Copyright 2007-2009. DK TECH CORPORATION. All Rights Reserved.
Swing-Out Ball Valves V83 Series
3
DK-LOK Tube Fitting End Connections
Basic Orderingnumber
EndConnection
Fractional DK-LOK
Metric DK-LOK
V83A-D4T-V83A-D6T-V83B-D8T-V83B-D12T-
V83C-D16T-
1/4 in.3/8 in.1/2 in.3/4 in.
1 in.
V83A-D6M-V83A-D8M-V83A-D10M-
V83B-D12M-
V83C-D25M-
6 mm8 mm10 mm
12 mm
25 mm
Orificemm in.
Dimension mm (in.)Cv
4.87.110.413.1
22.2
4.86.47.1
10.4
22.2
0.1880.2810.4110.516
0.875
1.23.87.513.6
40.0
0.1880.2500.281
0.411
0.875
1.22.53.8
7.5
40.0
L
80.8(3.18)
103.8(4.09)
136.7(5.38)
80.8(3.18)
103.8(4.09)
136.7(5.38)
L1
40.40(1.59)
51.90(2.04)
68.35(2.69)
40.40(1.59)
51.90(2.04)
68.35(2.69)
H
47.7(1.88)
64.8(2.55)
79.0(3.11)
47.7(1.88)
64.8(2.55)
79.0(3.11)
H1
31.8(1.25)
44.2(1.74)
61.9(2.44)
31.8(1.25)
44.2(1.74)
61.9(2.44)
H2
16.75(0.66)
22.25(0.88)
31.00(1.22)
16.75(0.66)
22.25(0.88)
31.00(1.22)
A
57.2(2.25)
111.0(4.37)
149.4(5.88)
57.2(2.25)
111.0(4.37)
149.4(5.88)
B
33.0(1.30)
44.5(1.75)
62.0(2.44)
33.0 (1.30)
44.5(1.75)
62.0(2.44)
Female Pipe Thread End Connections
Basic Orderingnumber
EndConnection
Female NPT Ends
Female ISO Tapered Ends
V83A-F2N-V83A-F4N-V83B-F6N-V83B-F8N-V83C-F12N-V83C-F16N-
1/8 in. 1/4 in. 3/8 in. 1/2 in. 3/4 in. 1 in.
7.1
13.1
22.2
V83A-F4R-
V83B-F8R-
V83C-F12R-
V83C-F16R-
1/4 in.
1/2 in.
3/4 in.
1 in.
3.8
12.0
31.0
38.0
7.1
13.1
22.2
0.281
0.516
0.875
55.4(2.18)
68.9(2.71)
92.0(3.62)
55.4(2.18)
68.9(2.71)
92.0(3.62)
114.3(4.50)
27.70(1.09)
34.45(1.36)
46.00(1.81)
27.70(1.09)
34.45(1.36)
46.00(1.81)
57.15(2.25)
47.7(1.88)
64.8(2.55)
79.0(3.11)
47.7(1.88)
64.8(2.55)
79.0(3.11)
31.8(1.25)
44.2(1.74)
61.9(2.44)
31.8(1.25)
44.2(1.74)
61.9(2.44)
16.75(0.66)
22.25(0.88)
31.00(1.22)
16.75(0.66)
22.25(0.88)
31.00(1.22)
0.281
0.516
0.875
3.8
12.0
31.038.0
Orificemm in.
Dimension mm (in.)Cv
L L1 H H1 H2
57.2(2.25)
111.0(4.37)
149.4(5.88)
57.2(2.25)
111.0(4.37)
149.4(5.88)
33.0(1.30)
44.5(1.75)
62.0(2.44)
33.0(1.30)
44.5(1.75)
62.0(2.44)
A B
Swing-Out Ball Valves V83 Series
Copyright 2007, 2008 DK TECH CORPORATION, All Rights Reserved.
Tube and Pipe Socket Weld End Connections
Basic Orderingnumber
EndConnection
Tube Socket Weld
Pipe Socket Weld
V83A-SW4T-
V83A-SW6T-
V83B-SW8T-
V83B-SW12T-
V83C-SW16T-
1/4 in.
3/8 in.
1/2 in.
3/4 in.
1 in.
V83B-SW8P-
V83C-SW12P-
V83C-SW16P-
1/2 in.
3/4 in.
1 in.
4.8
7.1
10.4
13.1
22.2
13.1
22.2
0.188
0.281
0.411
0.516
0.875
0.516
0.875
1.2
3.8
7.5
13.6
40.0
15.0
36.0
42.0
6.50(0.26)
9.70(0.38)
12.90(0.51)
19.20(0.76)
25.65(1.01)
21.80(0.86)
27.20(1.07)
33.90(1.33)
Orificemm in.
Dimension mm (in.)Cv
OD
13.70(0.54)
17.10(0.67)
21.30(0.84)
26.70(1.05)
33.40(1.31)
31.20(1.23)
42.16(1.66)
45.30(1.78)
X
7.1(0.28)
7.9(0.31)
9.7(0.38)
11.2(0.44)
16.0(0.63)
9.7(0.38)
12.7(0.50)
D
55.4(2.18)
68.9(2.71)
92.0(3.62)
68.9(2.71)
92.0(3.62)
L
27.70(1.09)
34.45(1.36)
46.00(1.81)
34.45(1.36)
46.00(1.81)
L1
47.7(1.88)
64.8(2.55)
79.0(3.11)
64.8(2.55)
79.0(3.11)
H
31.8(1.25)
44.2(1.74)
61.9(2.44)
44.2(1.74)
61.9(2.44)
H1
16.75(0.66)
22.25(0.88)
31.00(1.22)
22.25(0.88)
31.00(1.22)
H2
57.2(2.25)
111.0(4.37)
149.4(5.88)
111.0(4.37)
149.4(5.88)
A
33.0(1.30)
44.5(1.75)
62.0(2.44)
44.5(1.75)
62.0(2.44)
B
Pipe Butt Weld End Connections
Basic Orderingnumber
EndConnection
V83A-W4P10-
V83B-W8P10-
V83C-W12P10-
V83C-W16P10-
Orificemm in.
Dimension mm (in.)Cv
OD ID L L1 H H1 H2 A BSchedule 10
V83A-W4P40-
V83B-W8P40-
V83C-W12P40-
V83C-W16P40-
Schedule 40
V83A-W4P80-
V83A-W6P80-
V83B-W8P80-
V83B-W12P80-
V83C-W16P80-
1/4 in.
1/2 in.
3/4 in.
1 in.
1/4 in.
1/2 in.
3/4 in.
1 in.
1/4 in.
3/8 in.
1/2 in.
3/4 in.
1 in.
4.8
13.1
22.2
4.8
13.1
22.2
4.8
7.1
10.4
13.1
22.2
0.188
0.516
0.875
0.188
0.516
0.875
0.188
0.281
0.411
0.516
0.875
1.2
15.0
36.0
40.0
13.70(0.54)21.30(0.84)26.67(1.05)33.40(1.31)
10.40(0.41)17.10(0.67)22.45(0.88)27.90(1.10)
52.4(2.06)68.9
(2.71)92.0
(3.62)88.9
(3.50)
26.20(1.03)34.45(1.36)46.00(1.81)44.45(1.75)
47.7(1.88)64.8
(2.55)
79.0(3.11)
31.8(1.25)44.2
(1.74)
61.9(2.44)
16.75(0.66)22.25(0.88)
31.00(1.22)
57.2(2.25)111.0(4.37)
149.4(5.88)
33.0(1.30)44.5
(1.75)
62.0(2.44)
1.2
15.0
36.0
40.0
13.70(0.54)21.30(0.84)26.67(1.05)33.40(1.31)
9.20(0.36)15.80(0.62)20.93(0.82)26.60(1.05)
52.4(2.06)68.9
(2.71)92.0
(3.62)88.9
(3.50)
26.20(1.03)34.45(1.36)46.00(1.81)44.45(1.75)
47.7(1.88)64.8
(2.55)
79.0(3.11)
31.8(1.25)44.2
(1.74)
61.9(2.44)
16.75(0.66)22.25(0.88)
31.00(1.22)
57.2(2.25)111.0(4.37)
149.4(5.88)
33.0(1.30)44.5
(1.75)
62.0(2.44)
1.2
3.8
7.5
13.6
40.0
13.70(0.54)17.10(0.67)21.30(0.84)26.70(1.05)33.40(1.31)
7.70(0.30)10.70(0.42)13.90(0.55)18.80(0.74)23.90(0.94)
52.4(2.06)
68.9(2.71)
88.9(3.50)
26.20(1.03)
34.45(1.36)
44.45(1.75)
47.7(1.88)
64.8(2.55)
79.0(3.11)
31.8(1.25)
44.2(1.74)
61.9(2.44)
16.75(0.66)
22.25(0.88)
31.00(1.22)
57.2(2.25)
111.0(4.37)
149.4(5.88)
33.0(1.30)
44.5(1.75)
62.0(2.44)
Schedule 80
4
Swing-Out 3-Piece Ball Valves V83 Series
5
Swing-Out Ball Valves V83 Series
The vent passage is isolated from the ball bore. The valve in closed position, system fluidsvent through vent passage to the vent port.The valve in open position, no venting occurs, system fluids flow through the valve.Choose either the Downstream Vent (DV) or Upstream Vent (UP) option.
External Vent Options
Seat Material Valve Series Pressure, bar (psi) Pressure @ Max. Temp.
Reinforced PTFEVirgin PTFECarbon PTFE
PEEK
UHMWPE
V83A
V83B
V83C
V83A
V83B
V83C
V83A
V83B
V83C
68.9 (1000)@ -28 to 37 C(-20 to 100 F)
68.9 bar @ 232 C (100 psig @ 450 F)
68.9 bar @ 232 C (100 psig @ 450 F)
55 bar @ 232 C (800 psig @ 450 F)
17 bar @ 121 C (250 psig @ 250 F)
External Vented Valve Rating Upstream and downstream
SWING-OUT BOLT Unscrew the swing-out bolt and loosen otherthree bolts. This allows users to swing-out thebody, keeping the valve in-line.
Maintenance Kits
All dimensions shown in this catalog are for reference only and are subject to change.Dimensions with DK-LOK nuts are in finger-tight position.We reserve the right to change specifications stated in this catalog for our continuing program of improvement.
Seat Seal KitsKit contains each two pieces of seats, seat support rings, discsprings and flange seals.
To order, add - SEAT as a suffix to the ordering number. i.e., V83B-PK-VT-SEAT
Valve Series
V83A-
V83B-
V83C-
Seat Material DesignatorNil: Reinforced PTFEVP: Virgin PTFECP: Carbon PTFEPK: PEEKUH: UHMWPE
Flange Seal Designator
Nil: Reinforced PTFEVT: FKM O-ring
Packing Seal KitsKit contains each one piece of upper & lower packing, packinggland, packing support and stem bearing.
To order, add - PKG as a suffix to the ordering number. i.e., V83B-PK-PKG
Valve Series
V83A-
V83B-
V83C-
Packing Material Designator
Nil: Reinforced PTFE
Stem Bearing Designator
PK: PEEK7: X750
Flange Seal KitsKit contains two flange seals.
To order, add - FL as asuffix to the orderingnumber.i.e., V83A-VT-FL
Valve Series
V83A-
V83B-
V83C-
Flange Seal Designator
Nil: Reinforced PTFEVT: FKM O-ring
Valve Series
V83A-
V83B-
V83C-
Fastener Material
Gr. B8M
Fastener KitsKit contains each four pieces of body fasteners, body hex nutsand one stem nut.
To order, add - BOLTas a suffix to theordering number. i.e., V83A-BOLT
The selection of a valve for any application or system design must be considered to ensure safe performance.Valve function, valve rating, material compatibility, proper installation, operation and maintenance remain the sole responsibillty ofthe system designer and the user. Dk Tech accepts no liability for any improper selection, installation, operation or maintenance.
Safe Valve Selection
ea
aea
Swing-Out Ball Valves V83 Series
Select applicable valve pattern, seat options, pneumatic actuator, and the actuator temperature option from designator listed below.How to Order
P series Rack and Pinion Pneumatic Actuator
Table 3. Double Return 90 Deg. Actuator
V83A-D4T - PK - VT -PCS1 -HT -SV83C-D25M - 7 -PD2 -S
Seat Material
Nil: Reinforced PTFEVP: Virgin PTFECP: Carbon PTFEPK: PEEKUH: UHMWPE
StemBearing
Nil: PEEK7: X750
Flange Seals
Nil: PEEKVT:FKM O-ring
External Vent
UV: ExternalUpstreamDV: ExternalDownstream
Handle
Nil:Lever HandleOH:Oval Handle
FactoryAssembledActuator
Single return, see Table 2.
Double return, see Table 3.
ActuatorTemperatureOptions
Nil:Standard Temp.LT: Low Temp.HT: High Temp.
Body & FlangeMaterial
S: A351 CF8ML: A351 CF3MC: A216 Gr. WCB
Table 2. Single Return 90 Deg. Actuator
Actuator Material of Construction Table 1. Technical Information
Piston (Rack) Drive Shaft (Pinion)
SpringEnd CapO-Ring
Body
PartsExtruded Aluminum Alloy with external & internalcorrosion protection.
Standard Matetial
Die Cast Aluminum Alloy Anodized. Steel Alloy Nickel Plated.Spring Alloy Steel Nickel Plated. (min. 5, max. 12 spring)Die Cast Aluminum Alloy Polyester Coated.NBR is standard. Optional FKM and Silicon.
Actuator operating temperature ( oC)Standard: NBR O-Ring - 20 to 80.Low Temperature: Silicon O-Ring -40 to 80 (Designator: LT).High Temperature: FKM O-Ring -15 to 150 (Designator: HT).
Air-pressure: Min. 2.5 bar, Max. 8 bar.Air supply end connection: Female G 1/8 inch (ISO 228-1).Position indicator is standard.
Mount bracket: Field assembly kit includes mount bracket, valve to actuator connector, special size of valve body fasteners, fastener washers,bracket bolts and assembly manual.
118.0 62.0
58.0
2-1/8"G
24.0
86.0
20.0
66.0
25.0
31.0
C
A B
Model shown:V83A singleV83A doubleV83B double
A,B dimensionV83A: 40.71V83B: 52.24
C dimensionV83A: 61.45V83B: 65.62
Unit: mm
AirConsumption
Liter
Moment ValuesP=6 bar
Nm
Weight
Kg
V83A-SMBV83B-SMBV83C-SMB
0.100.150.49
3.57.417.7
0.91.133.09
DimensionsL x H x Wunit: mm
118x86x62140.5x89x70.5210.5x122x94.5
NormalOpenPOS1POS3POS4
NormalClosePCS1PCS3PCS4
Valveseries
V83AV83BV83C
Nill: Standard Temp.LT: Low Temp.HT: High Temp.
Mounting BracketOrdering Number
Actuator OperatingTemperature Options
Ordering Number
AirConsumption
Liter
Moment ValuesP=6 bar
NmV83A-DMBV83B-DMBV83C-DMB
0.100.100.15
14.414.419.9
L x H x Wunit: mm
118x86x62118x86x62
140.5x89x70.5
WeightUnit: Kg
OrderingNumber
0.750.751.03
PD1PD1PD2
Valveseries
V83AV83BV83C
Nill: Standard Temp.LT: Low Temp.HT: High Temp.
Mounting BracketOrdering Number
Actuator OperatingTemperature Options
Catalog No. V86-7March 2009
V86 Series Ball Valves, High Pressure 2-way & 3-way Ball Valves
VC86 Series CNG Ball Valves, 2-way Ball Valves
High pressure up to 10 000 psi (689 bar).Blowout proof design with internally loaded stem. Handle indicates the flow direction. Positive stop with robust stop pin.High flow rate with maximum orifice. Various end ports including Dk-Lok tube port.Various flow control with a side or bottom inlet port on 3-way valves.
Features
ECE R110 Manual Valves
Table 1. Materials of Construction
Component
BodyBall
Seat (2)
Disc Spring (2)
End Seal (2)
End Connector (2) Stem
Bearing
PackingGlandLever HandleOptional Oval HandleWasherStem NutStop Pin
12
3
4
5
67
8
910
11
121314
Valve Body Materials
SS316/ASTM A276 or A479 or ASTM A479
PVDF, standard for V86 seriesPEEK, standard for VC86 series
TYPE 631Disc spring, standard for VC86 series
CNG valve only.
FKM Oring for V86 seriesHNBR O-ring for VC86 series
SS316/ ASTM A276 or ASTM A479
PTFE, standard for V86 seriesPEEK, standard for VC86 series
Carbon PTFESS316/ ASTM A276 or ASTM A479
SS304 handle with vinyl sleeve
SS304SS304SS304
Classification: Class 0Service Pressure: 200 bar (2900 psig) Working Pressure: 260 bar (3770 psig) Temperature: - 40 to 105 C (-40 to 221 F)
VC86 series CNG ball valves
VC86 valve with live loaded compensation disc spring reactson ball movement for sealing at low and high CNG pressure. VC86 series standard PEEK and PCTFE seats are compatiblewith CNG.
End Connections: Dk-Lok tube port 12 to 16 mm OD (1/2 to 3/4 in. OD) Pipe Thread 1/2 to 1 in.
Wetted parts and lubricants listed in blue.Fluorinated-based lubricant
Optional Oval Handle
2-Way On-Off Valves
V86AV86BV86C
10.000
8,000
6,000
4,000
2,000
-54 0 50 100 150 200 230 C-65 32 122 212 302 392 446 F
psig689
551
413
275
137
bar
0 0
V86A
V86B, V86C
Valve Ordering Information and Dimensions
* V86D body is round bar construction.CNG valve ordering number : The basic ordering number listed in blue represents VC86 as well as V86 series ball valve. Valve
Series0 (0)
3.92 ( )7.35 ( )12.26 ( )
2.895.429.04
344 (5000)
-10.30 ( )19.61 ( )
7.5914.62
Pressure/Temperature RatingsV86 2-way valve with PEEK seat
System Pressures, bar (psig)
1/4 in. Dk-Lok3/8 Dk-Lok1/2 Dk-Lok1/4 Female NPT3/8 Female NPT1/2 Female NPT1/4 Male NPT3/8 Male NPT1/2 Male NPT1/2 Female NPT3/4 Female NPT12mm Dk-Lok
5/8 Dk-Lok3/4 Dk-Lok3/4 Female NPT 1 3/4 in. Dk-Lok 1 in. 3/4 in. Male NPT 1 in.
in.in.in.in.in.in.in.in.in.in.
in.in.in.in. Female NPT
Dk-Lok
Male NPT
V86A-
V86B-VC86B-
V86C-VC86C-
V86D-VC86D-
1.23.7
7.5
3.77.27.5
10.1
30.0
30.019.0
19.030.0
D-4TD-6TD-8TF-4NF-6NF-8NM-4NM-6NM-8NF-8NF-12ND -12M
D-10TD-12TF-12NF-16ND-12TD-16TM-12NM-16N
4.8 ( )0.197.1 ( )0.28
10.0 ( )0.39
7.1 ( )0.28
10.0 ( )0.39
10.0 ( )0.39
10.4 ( )0.41
12.7 ( )0.50
12.7 ( )0.50
12.7 ( )0.50
132.00 ( )5.20 84.10 ( )3.31 80.0*( )3.15
19.0 ( )0.75
15.7 ( )0.6219.0 ( )0.7515.7 ( )0.6219.0 ( )0.75
Basic Ordering Number
96.00 ( )102.50 ( )107.60 ( )74.00 ( )77.00 ( )85.00 ( )95.40 ( )95.40 ( )
100.20 ( )89.00 ( )90.00 ( )
110.00 ( )
116.00 ( )115.00 ( )108.00 ( )127.00 ( )125.00 ( )134.00 ( )119.00 ( )129.00 ( )
3.784.044.242.913.033.353.763.763.943.503.544.33
110.00 ( )4.3316mm Dk-LokD -16M1/2 in. Dk-LokD -8T
4.56
116.00 ( )4.56
4.52
Full Bore
4.255.004.925.274.685.07
1 in. Female NPTF -16N 25.0 ( )0.98 112.90 ( )4.44
Dimensions mm ( ) in.A H L SQ
CvOrifice
mm ( )in.End ConnectionsInlet & Outlet
108.3( )
149.0( )
149.0( )
4.26
5.86
5.86
38.4( )
51.0( )
56.0( )
1.52
2.00
2.20
32.0( )
40.0( )
50.0( )
1.26
1.57
1.97
Torque Unit: Nm ( )lbs-ft413 (6000)
6.37 ( )--
4.69
Ball Valves V86, VC86 Series
2001-2009, DK TECH CORPORATION, All Right Reserved. 2
Operation
Factory Test
Table 2. 2-Way Valve Actuation Torque
2-way positive shut off and 3-way directional control of fluids inprocess, power and instrument application.Valves are designed to control fluids in full open or full closed position.
Valves that have not been actuated for a period of time mayhave a higher initial actuation torque.Valves must be in open position during system test not todamage the valve seat. Sour Gas Service NACE MR0175 available.
Every valve is tested with nitrogen gas @1000 psig (68 bar) for leakage atthe seat to a maximum allowable leak rate of 0.1 SCCM. The stem packingis tested with nitrogen gas @1000 psig for no detectable leakage.
Cleaning and PackagingValves are cleaned and packaged in accordance with Dk TechDC-01 cleaning standard. Special cleaning for oxygen serviceis available on request.
A
SQ
L
V86D series
( )
( )
( )
( ) ( )
V86A
V86BV86C
V86D
ValveSeries
Seat
PVDF
PVDF
PCTFE
PCTFE
PCTFE
PEEK
PEEK
TemperatureRating
3-way Diverter Valves
SIDE PORT INLET1/4 turnActuation
BOTTOM PORT INLET1/2 turnActuation
Outlet Outlet
Inlet
A
L
SQSQ
H
H1
Ordering Information and Dimensions
6,000 (413)
10,000 (689)
5,000 (344)
6,000 (413)
5,000 (344)
Allowable WorkingPressure
at ambient temperaturepsig(bar)
OutletOutlet
A
H1
86 Series
Inlet
L
R
V86A-
V86B-
V86C-
BasicOrdering Number
Dimensions mm ( )in.A H H1 L
SQOrificemm ( )in.
End Connections
1/4 in. Dk-Lok3/8 Dk-Lok1/2 Dk-Lok1/4 Female NPT3/8 Female NPT1/2 Female NPT1/2 Female NPT3/4 Female NPT5/8 Dk-Lok3/4 Dk-Lok3/4 Dk-Lok
1 Dk-Lok3/4 Female NPT
1
in.in.in.in.in.in.in.in.in.in.in.in.in. Female NPT
3*- D-4T-3*- D-6T-3*- D-8T-3*- F-4N -3*- F-6N-3*- F-8N-3*- F-8N-3*- F-12N-3*- D-10T-3*- D-12T-3*- D-12T-3*- D-16T-3*- F-12N-3*- F-16N-
10.0 ( )0.39
7.1 ( )0.284.8 ( )0.19
12.7 ( )0.50
15.7 ( )0.62
19.0 ( )0.75
108.34.26
149.05.86
( )149.05.86
38.41.52
51.02.00
56.02.20
50.9 ( )53.0 ( )55.8 ( )40.0 ( )41.5 ( )45.5 ( )55.0 ( )55.0 ( )67.2 ( )67.7 ( )75.3 ( )80.0 ( )59.5 ( )67.0 ( )
2.002.092.201.571.641.792.172.172.662.662.963.152.342.64
96.0 ( )102.5 ( )107.6 ( )74.0 ( )77.0 ( )85.0 ( )89.0 ( )90.0 ( )
114.4 ( )115.0 ( )125.0 ( )134.0 ( )96.0 ( )
111.0 ( )
3.784.044.242.913.033.353.53.544.54.524.925.273.784.37
32.0( )
40.0( )
50.0( )
1.26
1.57
1.97
All dimensions shown are for reference only and are subject to change.
Table 4. 2-way Valve Pressure and Temperature Rating
Table 3. 3-way Valve Actuation Torque
Table 5. 3-way Valve Pressure and Temperature Rating
V86AV86B
3.92 ( )7.35 ( )
2.895.42
V86 3-way ball valve is designed to switch media through the inlet port and direct it to out of two outlet ports.
Side and Bottom Port Valvalve Ordering InformationTo order side port entry valve, replace * with SS, to order bottom port entryvalve, replace * with B. Examples: V86A-3SS-D-4T-S, V86A-3BB-D-4T-S.
ValveSeries
System Pressures, bar (psig)0 (0) 206 (3000) 275 (4000)
Torque Unit: Nm (Ibs-ft)4.90 ( )
-4.69-
7.85 ( )5.78
V86A
V86BV86C
ValveSeries
Seat
PVDF-30 to 130
(-22 to 266 )
-30 to 180(-22 to 356 )
-40 to 230
PVDF
PCTFE
PCTFE
PEEK
PEEK
TemperatureRating
4,000 (275)
6,000 (413)
3,000 (206)
4,000 (275)
Allowable WorkingPressure
at ambient temperaturepsig(bar)
-30 to 130(-22 to 266 )-30 to 180
(-22 to 356 )-40 to 230
(-40 to 446 )-30 to 110
(-22 to 230 )
-30 to 160(-22 to 320 )-40 to 210
(-40 to 410 )-30 to 160
(-22 to 320 )
(-40 to 446 )
-30 to 110(-22 to 230 )
-30 to 160(-22 to 320 )
-40 to 210(-40 to 410 )
Ball Valves V86, VC86 Series
3
Ordering Information
Options
mm ( )in.
Nil: PEEK, standard for VC86B, VC86C seriesNil: PCTFE, standard for VC86D seriesNil: PVDF, standard for V86 seriesPC: PCTFEPK: PEEKPD: PVDF
P1: Locking nut panel mountingP2: �Screw hole panel mounting
LD: Locking Device
Locking Nut
Panel
86 S
erie
sR
L L1 t T
V86A
V86B
V86C
The selection of a valve for any application or system design must be considered to ensure safe performance.Valve function, valve rating, material compatibility, proper installation, operation and maintenance remain the sole responsibillty of the system designer and the user. Dk Tech accepts no liability for any improper selection, installation, operation or maintenance.
Safe Valve Selection
mm ( )in.
34.0 ( )
36.0 ( )
40.0 ( )
1.33
1.42
1.57
26.0 ( )
29.0 ( )
35.0 ( )
1.02
1.14
1.37
4.0 ( )
5.0 ( )
6.0 ( )
0.15
0.20
0.23
30.0 ( )
38.0 ( )
38.0 ( )
1.18
1.50
1.50
Locking Nut Panel Mounting
Screw Hole Panel Mounting
"Lift-Turn" Locking Device Pad-Lock applicable 7.2mm (0.28 in) holeconstructed on upperlocking detent.
Ordering designator : P1
Disassemble the handle prior to panel mounting.Addition locking nut below handle makes the valve panel mountable.
Ordering designator : P2
Disassemble the handle prior to panel mounting.
Additional four (4) screw holes on the top of valve makes the valve panel mountable.
Ordering designator : LDDk Tech patented "Lift-Turn" safety locking device allows you to lock the valve manually either in open or close position.The locking device consists of study upper and lower locking detents made out of stainless steel.
Panel Thickness
V86A
V86B
V86C
30.0 ( )
38.0 ( )
38.0 ( )
1.18
1.50
1.50
Max. 4.0 ( )0.157
Panel Hole DrillValve Series
Valve Series
You may apply a pad-lock to secure the valve in the openor close position.
Select the desired basic ordering number, and options from designators listed below.
V86A-D-4TV86B-F -12NVC86B-D-12M
-PC - OH -S -S -S -S -S
-LD
Nil: Standard Lever HandleOH: Oval Handle
OH option is applicable to 2-way V86A series valves.
Valve Material
HandleHandleLocking DeviceLocking DevicePanel MountingSeat
Note: This option is applicable to 2-way valves.
S316
L1t
TL
ea
aea
Ball Valves V86, VC86 Series
Catalog No. VH86-4Oct. 2009
VH86 seriesHigh Pressure Multi Purpose Ball Valves
High flow in a compact design. High pressure capacity designed for blow-out proof with internally loaded ball stem. Micro-finished ball provides a positive seal.90 degree actuation for 2-way and 180 degree actuation for 3-way ball valves.Panel mounting as standard.Chevron stem seal, adjustable with the handle disassembled.Handle indicates flow direction.Low operating torques and positive handle stops.Optional pneumatic actuation.
VH86 valves are designed to control fluid in full open and closed position, using VH86 valves to throttle the flow may reducethe valve life. Stem packing can be adjustable with the handle disassembled. Tighten packing bolt clockwise to tighten the stem packing. Valves that have not been actuated for a period of time may have a higher initial actuation torque.If the valve system needs to be tested at higher pressure than the valve maximum pressure, the valve must be in openposition during the test so as not to damage the valve seat. Optional Sour Gas Service applicable.
Features
Material of Construction
Components
1. Handle2. Set Screw3. Panel Nut4. Packing bolt*5. Upper / Lower Gland 6. Stem Chevron Packing7. Stem 8. Body 9. Ball
10. Seat (2)
11. Retainer (2)12. Retainer Seal (2)13. End Connector Seal (2)14. End Connector (2)
Nylon with brass insertStainless steel
PTFE/D1710 type 1, Grade 1, Class BSS316/A276
SS316/A276 Type F316SS316/A276
Standard PCTFE (Kel-F), optional PTFE, PEEK
SS316/A276
SS316/A276
SS316/A276
Valve Body MaterialStainless Steel
Grade/ASTM Specification
PTFE/D1710 type 1, Grade 1, Class B
* Molybdenum disulfide with hydrocarbon coatingWetted parts and lubricants are listed in blue.Lubricant is Fluorinated-based.
Operation and Packing Adjustment
VH86 series ball valve offers a safe and reliable performance in a wide range of onshore and offshore applications: Water, oil,gas, petrochemical in heavy duty applications.
Application
Every valve is factory tested with nitrogen gas at 1000 psig (68.9 bar) for leakage at seat to a maximum allowable leak rate of 0.1 SCCM. The packing is tested with nitrogen gas for no detectable leakage. Every valve is cleaned and packaged in accordance with DK cleaning standard DC-01.
Factory Test, Cleaning and Packaging
VVaallvveess VH86 Series Multi Purpose Ball Valves
2005-2009, DK TECH CORPORATION. All Right Reserved. 2
Bi-directional 2-way Ball Valves
Technical DataValveSeries
Pressure Rating@-27 to 37 OC (-20 to 100 OF)
Sealing MaterialsSeatPCTFEPEEKPTFE
Stem PackingPTFEPTFEPTFE
Retainer / End SealPTFEPTFEPTFE
6000 psig (413 bar)6000 psig (413 bar)1500 psig (103 bar)
Temperature Rating
-30 to 180 OC (-22 to 355 OF)-54 to 230 OC (-65 to 446 OF)-30 to 176 OC (-22 to 349 OF)
VH86A, VH86B,and VH86C series
PCTFE is standard seat material.
Ordering Information and DimensionsBasic Ordering
NumberEnd Connections Orifice
Inlet Outlet mm
VH86B-
VH86A-
D-1T-D-2T-F-2N-M-2N-D-4T-M-4N-D-3M-D-2T-D-4T-MD-4N4T-FD-4F4T-F-4N-M-4N-MF-4N-MD-4N6T-FD-4N6T-D-6T-M-6N-D-6M-D-8M-D-10M-F-6N-F-8N-D-8T-M-8N-D-12T-D-12M-D-16M-
1/16” Dk-Lok1/8” Dk-Lok
1/8” Female NPT1/8” Male NPT1/4” Dk-Lok
1/4” Male NPT3mm Dk-Lok
1/8 in. Dk-Lok1/4 in. Dk-Lok
1/4 in. Female NPT1/4 in. Male NPT
3/8 in. Dk-Lok3/8 in. Male NPT
6 mm Dk-Lok8 mm Dk-Lok10 mm Dk-Lok
3/8 in. Female NPT1/2 in. Female NPT
1/2 in. Dk-Lok1/2 in. Male NPT3/4 in. Dk-Lok12 mm Dk-Lok16 mm Dk-Lok
1.32.44.24.24.24.22.22.4
4.7
6.4
4.7
10.3
9.510.3
inch0.0520.0930.1650.1650.1650.1650.0860.093
0.187
0.25
0.187
0.406
0.3750.406
Dimensions mm (in.)L1 L2 H1
82.2 (3.24)89.0 (3.50)90.4 (3.56)92.0 (3.62)99.0 (3.90)
109.20 (4.30)118.8 (4.68)112.8 (4.44)
118.4 (4.66)
1/4 in. Female NPT3/8 in. Dk-Lok3/8 in. Dk-Lok
1/4 in. Dk-Lok1/4 in. Dk-Lok
1/4 in. Male NPT1/4 in. Female NPT
1/4 in. Male NPT 1/4 in. Male NPT
1/4 in. Female NPT
VH86C-
All dimensions shown are for reference only and are subject to change. Dimensions with DK-LOK nuts are in finger-tight position.
6.4 0.25
Cv
44.2 (1.74)
38.4 (1.51)41.1 (1.62)38.4 (1.51)
33.0 (1.30)34.5 (1.36)27.2 (1.07)30.0 (1.18)37.6 (1.48)34.3 (1.35)34.8 (1.37)41.9 (1.65)
33.0 (1.30)34.5 (1.36)27.2 (1.07)30.0 (1.18)37.6 (1.48)34.3 (1.35)34.8 (1.37)41.9 (1.65)44.2 (1.74)41.1 (1.62)38.4 (1.51)38.4 (1.51)
41.1 (1.62)
38.4 (1.51)45.7 (1.8)
45.7 (1.8)
10.7(.42)
17.5(.69)
H2
11.9(.47)
17.8(.70)
H
38.9(1.53)
44.2(1.74)
A
25.4(1.00)
38.1(1.50)
D
19.6(.77)
22.9(.90)
T
6.4(.25)
9.7(.38)
0.060.210.430.430.430.430.180.26
1.04
2.34
1.04
6.42
5.576.42
2.34
8.4(.33)
9.5(.37)
24.8(.98)
19.1(.75)
14.7(.58)
3.3(.13)
VVaallvveess VH86 Series Multi Purpose Ball Valves
3
3-way Diverter Ball Valves
Technical DataValveSeries
Pressure Rating@-27 to 37 OC (-20 to 100 OF)
Sealing MaterialsSeatPCTFEPEEKPTFEPCTFEPEEKPTFE
Stem PackingPTFEPTFEPTFEPTFEPTFEPTFE
Retainer / End SealPTFEPTFEPTFEPTFEPTFEPTFE
6000 psig (413 bar)6000 psig (413 bar)1500 psig (103 bar)4000 psig (275 bar)6000 psig (413 bar)1500 psig (103 bar)
Temperature RatingOC ( OF)
-30 to 180 (-22 to 355)-54 to 230 (-65 to 446)-30 to 176 (-22 to 349)-50 to 180 (-58 to 355)-54 to 230 (-65 to 446)-30 to 176 (-22 to 349)
VH86B-3BVH86C-3B
VH86A-3B
Ordering Information and DimensionsBasic Ordering
Number End Connections CvOrifice Dimensions mm (in.)
mm
VH86B-3B-
VH86A-3B-
VH86C-3B-
D-1T-D-2T-F-2N-M-2N-D-4T-M-4N-D-2T-D-4T-F-4N-DDM-4T4N-*M-4N-D-6T-M-6N-D-6M-D-8M-D-10M-F-6N-F-8N-D-8T-DDF-8T8F-*M-8N-D-12T-D-12M-D-16M-
1/16” Dk-Lok1/8” Dk-Lok1/8” Female NPT1/8” Male NPT1/4” Dk-Lok1/4” Male NPT1/8" Dk-Lok1/4" Dk-Lok1/4" Female NPT1/4" Dk-Lok,1/4" Male NPT1/4" Male NPT3/8" Dk-Lok3/8" Male NPT6 mm Dk-Lok8 mm Dk-Lok10 mm Dk-Lok3/8" Female NPT1/2" Female NPT1/2" Dk-Lok1/2" Dk-Lok,1/2" Female NPT1/2" Male NPT3/4" Dk-Lok12 mm Dk-Lok16 mm Dk-Lok
1.32.44.24.24.24.22.44.75.04.7
5.0
4.7
10.3
9.510.3
Inch0.0520.0930.1650.1650.1650.1650.0930.1870.1960.187
0.196
0.187
0.406
0.3750.406
L133.0 (1.30)34.5 (1.36)27.2 (1.07)30.0 (1.18)37.6 (1.48)34.3 (1.35)41.9 (1.65)44.2 (1.74)38.4 (1.51)44.2 (1.74)41.1 (1.62)45.7 (1.8)41.1 (1.62)44.5 (1.75)45.2 (1.78)46.0 (1.81)49.5 (1.95)54.6 (2.15)
56.4 (2.22)
56.9 (2.33)
0.060.210.630.590.630.590.210.700.870.70
0.87
0.70
3.62
3.463.62
5.0 0.196
59.2 (2.33)
59.4 (2.34)
L233.0 (1.30)34.5 (1.36)27.2 (1.07)30.0 (1.18)37.6 (1.48)34.3 (1.35)41.9 (1.65)44.2 (1.74)38.4 (1.51)44.2 (1.74)41.1 (1.62)45.7 (1.8)41.1 (1.62)44.5 (1.75)45.2 (1.78)46.0 (1.81)49.5 (1.95)54.6 (2.15)
56.4 (2.22)
56.9 (2.33)
H135.3 (1.39)36.8 (1.45)29.2 (1.15)32.0 (1.26)39.6 (1.56)36.3 (1.43)45.5 (1.79)47.8 (1.88)41.9 (1.65)47.8 (1.88)44.7 (1.76)49.3 (1.94)44.7 (1.76)47.8 (1.88)48.5 (1.91)49.5 (1.95)58.2 (2.29)63.2 (2.49)68.1 (2.68)63.2 (2.49)65.8 (2.59)68.1 (2.68)67.8 (2.67)65.5 (2.67)
H2
11.9(.47)
17.8(.70)
H
38.9(1.53)
44.2(1.74)
A
25.4(1.00)
38.1(1.50)
D
19.6(.77)
22.9(.90)
T
6.4(.25)
8.4(.33)
23.9(.94)
19.1(.75)
14.7(.58)
3.3(.13)
9.7(.38)
59.2 (2.33)
59.4 (2.34)
0.87
All dimensions shown are for reference only and are subject to change. Dimensions with DK-LOK nuts are in finger-tight position.
VH86 3-way Ball Valve is designed to switch media through the bottom port and direct it to out of two outlet ports.
* VH86 3-way ball valves are described by first the outlet ports (1) and (2) and next the bottom inlet port (3).
21
3
Pressure-Temperature Curve
Legend: 2W:2-Way VH86 ball valves3W:3-Way VH86 ball valves
VVaallvveess VH86 Series Multi Purpose Ball Valves
ea
aea
The selection of a valve for any application or system design must be considered to ensure safe performance.Valve function, valve rating, material compatibility, proper installation, operation and maintenance remain the sole responsibillty ofthe system designer and the user. Dk Tech accepts no liability for any improper selection, installation, operation or maintenance.
Select applicable valve pattern, seat options, pneumatic actuator, and the actuator temperature option from designator listed below.
Safe Valve Selection
How to Order
P series Rack and Pinion Pneumatic Actuator
Table 3. Double Return 90 Deg. Actuator
VH86B-D-6T- - PK - PCS1 -HT -SVH86C-D-12T - SG -S
Seat Material
Nil: PCTFEPK: PEEKPE: PTFE
Sour Gas
SG: Sour GasFactory Assembled Actuator Valve Body Material
For single return, see Table 2.For double return, see Table 3.
Actuator Temperature OptionsNill: Standard Temp.LT: Low Temp.HT: High Temp.
S: S316
Table 2. Single Return 90 Deg. Actuator
Actuator Material of Construction Table 1. Technical Information
Piston (Rack) Drive Shaft (Pinion)
SpringEnd CapO-Ring
Body
Parts
AirConsumption
Liter
Moment ValuesP=6 bar
Nm
Weight
Kg
VH86A-SMBVH86B-SMBVH86C-SMB
0.10.9
DimensionsL x H x Wunit: mm
118x86x62
NormalOpen
NormalClose
PCS1
PCS2
POS1
POS2
3.5
5.0
Valveseries
VH86AVH86BVH86C
Nill: Standard Temp.LT: Low Temp.HT: High Temp.
Extruded Aluminum Alloy with external & internalcorrosion protection
Standard Matetial
Die Cast Aluminum Alloy Anodized. Steel Alloy Nickel Plated.Spring Alloy Steel Nickel Plated. (min. 5, max. 12 spring)Die Cast Aluminum Alloy Polyester Coated.NBR is standard. Optional FKM and Silicon.
Actuator operating temperature ( oC)Standard: NBR O-Ring - 20 to 80.Low Temperature: Silicon O-Ring -40 to 80 (Designator: LT).High Temperature: FKM O-Ring -15 to 150 (Designator: HT).Air-pressure: Min. 2.5 bar, Max. 8 bar.Air supply end connection: Female G 1/8 inch (ISO 228-1).Position indicator is standard.
Mounting BracketOrdering Number
Actuator OperatingTemperature Options
Ordering Number
AirConsumption
Liter
Moment ValuesP=6 bar
NmVH86A-DMBVH86B-DMBVH86C-DMB
0.114.4
L x H x Wunit: mm
118x86x62
WeightUnit: Kg
OrderingNumber
0.75PD1
Valveseries
VH86AVH86BVH86C
Nill: Standard Temp.LT: Low Temp.HT: High Temp.
Mounting BracketOrdering Number
Actuator OperatingTemperature Options
Mount bracket: Field assembly kit includes mount bracket, valve to actuator, bracket bolts and assembly manual.
Model shown:VH86B/C series
A dimensionVH86B: 25.00VH86C: 27.50
B dimensionVH86B: 62.00VH86C: 90.90
Unit: mm
Recommended