ECE 4991 Electrical and Electronic Circuits Chapter 10

ECE 4991 Electrical and Electronic ECE 4991 Electrical and Electronic CircuitsCircuits

Chapter 10Chapter 10

2

Where We AreWhere We Are• Chapter 2 - The basic concepts and practice at

analyzing simple electric circuits with sources and resistors

• Chapter 3 – More harder networks to analyze and the notion of equivalent circuits

• Chapter 4 – Capacitors and inductors added to the mix

• Chapter 5 – Analyzing transient situations in complex passive networks

• Chapter 8 – New subject – the wonders of operational amplifiers as system elements

• Chapter 9 – Introduction to semiconductors – the basics and diodes – more network analysis

• Chapter 10 – Bipolar junction transistors and how they work – now you can build your own op amp

3

What’s Important in What’s Important in Chapter 10Chapter 10

1. Definitions

2. How bipolar transistors work

3. Building a transistor

4. Transistor basics

5. Collector characteristics

6. Load lines and operating points

4

1. Definitions1. Definitions

• Bipolar transistor

• Emitter

• Base

• Collector

• NPN, PNP

• Gain ()

• Cutoff region

• Active linear region

• Saturation region

• Breakdown region

• Load lines

• Operating points

5

2. How Bipolar Transistors 2. How Bipolar Transistors WorkWork

• Transistors are made by creating a PNP (or NPN) “sandwich”

• Carriers are “emitted” by the emitter and “collected” by the collector

• The base controls how much gets through

6

Transistor OperationTransistor Operation• A small amount of base current can

control a large amount of collector current

• Gain = IC / IB =

7

Transistor Operation in Transistor Operation in SiliconSilicon

8

3. Building a Transistor3. Building a Transistor

9

Transistor FabricationTransistor Fabrication

10

4. Transistor Basics4. Transistor Basics

VBB

RB

+

VCC

RC

+

Typical NPN transistor schematic

11

There are four operating There are four operating regions for a transistorregions for a transistor

VBB

RB

+

VCC

RC

+

1. Cutoff Region – Both junctions reverse-

biased – Very little base or collector current

2. Active Linear Region – BE junction forward

biased, CB junction reverse-biased –

amplifying mode

3. Saturation Region – Both junctions forward

biased – low VCE – switch mode

4. Breakdown Region – Determines the

operating limits of the device

12

5. Collector Characteristics5. Collector Characteristics

VBB

RB

+

VCC

RC

+

“Collector characteristic” is a plot of

collector current versus collector-

emitter voltage for different base

currents

13

Collector CharacteristicsCollector Characteristics

“Collector characteristic” is a plot of

collector current versus collector-

emitter voltage for different base

currents

14

Real Transistor Collector Real Transistor Collector CharacteristicsCharacteristics

IB

= 10 µA, 20 µA, 30 µA, ... , 80 µA

15

6. Load Lines and Operating 6. Load Lines and Operating PointsPoints

IB

= 10 µA, 20 µA, 30 µA, ... , 80 µA

16

Consider this schematic…Consider this schematic…

VBB

RB

+

VCC

RC

+

• VCC = 15V, RC = 1000, VBB = 3V

• Design a circuit that operates around

the center of the active region collector

characteristics

17

First, generate a load line, First, generate a load line, then set the operating pointthen set the operating point

VBB

RB

+

VCC

RC

+

• VCC = 15V, RC = 1000 ,

VBB = 3V

• What is IC @ VCE = 0?

• What is VCE @ IC = 0?

• Generate load line

• Pick desired IB

• Set RB to get it IB

= 10 µA, 20 µA, 30 µA, ... , 80 µA

18

Practice with BipolarsPractice with Bipolars

19

Practice with BipolarsPractice with Bipolars

20

Practice with BipolarsPractice with Bipolars

21

Practice with BipolarsPractice with Bipolars

22

Practice with BipolarsPractice with Bipolars

23

Practice with BipolarsPractice with Bipolars