1

11

FAN1

1

IDE1 IDE2

LINE OUTPORT

EAR PHONE PORT

MIC INPORTUSB PORT1394 PORT

PWONBUTTON

RSTBUTTON

HDDLED

POWERLED

PS/2 MOUSE& KEYBOARD

PORTS

COM1 PORTPARALLEL PORTVGA

PORTLAN & USB PORTS

J10

Part List STEP 1

Hardware Installation

Installation Guide

Plastic Spacer (* 2)

CD-ROM Adapter Screws (* 3)

CD-ROM Screws (* 5)

Case Screws (* 2)

O

J EMI Sticker (*2)

M

P

N

Mainboard

L

K

CPU socket lift up to 90-degree.1

Install CPU into CPU socket. (Match socket pin 1 and CPU cut edge)

2

3

Install CPU cooler on top of CPU.Tighten CPU cooler with screws into pillaret.

4

DIMM socket push down to 45-degree.1Install memory module into the DIMM socket. 2

1

2

3

4

1

2

45

45

90

STEP 3

Install CD-ROM deviceInstall HDD device

STEP 2

Install CD-ROM adapter

Q

STEP 5Install Case

Install mainboard into the case. 1Tighten rear panel with screws on the case. 2

CPU

Installation Guide

Socket 478

screw

CPU cooler

Pillaret

Install CPU / Cooler

M0240

M0240

3

6

7

9

4

2

8

10

1

A1

A2A4

A3

A6 A5

B1B2B3B4B5B6B7B8

General Information

1 Intel 865G Chipset

2 Intel 82801EB Chipset

3 I/O Chipset

4 Audio CODEC Chipset

5 Flash EEPROM

6 CPU Socket 478

7 DDR DIMM Sockets

8 IDE Connectors

9 PC104 Plus Connector (option)

10 CPU FAN (FAN 1)

A1 RJ45 LAN Port

A2 USB Ports

A3 PS/2 Mouse Port

A4 PS/2 Keyboard Port

A5 19V Power In

A6 LINE-Out Port

A7 Parallel Port

A8 VGA Port

A9 RS232 COM Port

B1

B2 Power Button

B3 Reset Button

B4 HDD LED

B5 Power LED

B6 Ear Phone Port

B7

MIC-In Port

USB Port

B8 1394 Port

Item Checklist

Mainboard Layout

A8A9

A7

5

Install Memory

Please refer to "Hardware Installation" of "Installation Guide" for system installation procedure.

Barebone System Unpacking Guide

Procedure�

CPU Cooler Screws (* 4) Q

Installation Accessory Kit

CD-ROM

B

J

N

F

P

I1

*** Before next step, you have to complete the install CPU/cooler and memory installation. ***

Complete Memory

Complete CPU/cooler

Heatsink �Compuond

HDD & CD-ROMBracket

CD-ROM Adapter

CD-ROM 44-Pin Cable

UDMA ATA Cable

A

B

C

D

E

HDD Screws (* 5)

F

G

H

Print/COM/VGA Screws (* 6)

I

Front Panel

Rear Panel

Case

HDD

1

2

3

Install UDMA ATA cable to HDD device.

1

2

Tighten the HDD & bracket with screws. 4

Insert plastic spacer to the CD-ROM Adapter. Tighten CD-ROM Adapter and CD-ROM with screws.

1

3

1 Push the CD-ROM device to the bracket.

2

1

2

1

2

Loose the screws on the rear panel from the case. 1Pull out the mainboard from the case. 2

1

Glue the heatsink compound between the CPU and heatsink.

Push HDD into HDD & CD-ROM Bracket.Notice:The HDD's label side is down.

L

3

Paste EMI Stickers to the CD-ROM top.

CPU FAN Screws (* 2)

InstallationGuide

Specifications are subject to change without notice, reference only.

Specifications are subject to change without notice, reference only.

SIL

ICO

NE

HE

AT

SIN

K P

AS

TE

SIL

ICO

NE

HE

AT

SIN

K P

AS

TE

INK

PA

S Install Guide

CD

Heat-sink

Accessory Kit

Power Adapter

Power Cable

System Unit

PU Sponge

The system uses entire casing for

partial heat dissipation, so the

normal operating temperature is

between 40 C ~ 55 C.

Specifications are subject to change without notice, reference only.

WARNINGThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

* Reorient or relocate the receiving antenna.* Increase the separation between the equipment and receiver.* Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.* Consult the dealer or an experienced radio TV technician for help.

Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equivalent.

12

Install 12V power connector to HDD device.3

4

12

2 Install the CD-ROM 44-pin cable to the CD-ROM device.

3 Tighten the CD-ROM device and bracket with screws.

3

STEP 4Install FAN

1 Tighten FAN on CPU cooler with screws.

1

12

2 Connect CPU FAN connector to mainboard CPU FAN connector.

Stick the rubber stand. 3

3

Complete System

R

Heat Sink Paste (* 1) SILICONE HEAT

SINK PASTE

SILICONE HEAT

SINK PASTE

INK PAS

Rubber Stand (*4)

S

FAN

CD-ROM Adapter

&

&

19V EXT POWERPORT

A

G

I

C

M A

R

D

O

K

H