Note : SP = Standard Pack Quantity, g = Weight in Grams, F-T = Fusion Time in Seconds, C-T = Cooling Time in Minutes
4mm Pin Terminal 4.7mm Pin TerminalPE 100 Black
4 mm Pin TerminalPE 100 Black
4.7mm Pin Terminal
Electrofusion Coupler for Gas / Water - SDR11 (ISO S5)
PT KARO GRAHA ABADI
Crystal Shophouse CRL No 7Jl Gading Golf Boulevard
Gading Serpong - Indonesia, 15810TEL.: +62 21 5421 3636
MAIL : [email protected] : www.karograha.com
Common Applications:
Pipe to pipe connection during laying
Pipe connections in areas difficult to access, in narrow trenches
Repairing localised damages on pipes, connections of transition
fittings, pipe stub ends etc
Pipe Connections with spigot end fittings
Reinforcements of squeezed or kinked portions of permanently
laid down (immovable) pipes
Advantages :
• Standard Operating Voltage - 40 V
• Same fusion time for various SDR and PN rated pipes
• Higher penetration of pipe in the fittings enables proper alignment
• Optimal fusion and cold zone for a strong and sturdy joint
• Auto Temperature compensation for ambient conditions -5°C to +
40°C
• Clearance-Fit for ease of installation 20-125mm coupler with
knock down stopper & 140-315mm couplers are with removable
stopper
• Pop-Up fusion indicators to indicate fusion process performance
• Permanent Batch Indicator, Fusion Time, Cooling Time, Raw
Material Grade and SDR marking
• Each fitting individually packed in PE bag to protect against
contamination and oxidation
• Each fitting with water-proof bar code to automatically feed fusion
data to the Control-box for fusion process
Kimplas Electrofusion Couplers, manufactured in PE100 (Black) grade are Standard SDR 11 rated (PN 16). Kimplas Electrofusion fittings are
suitable for permanently connecting MDPE 80 and PE 100 pipes, both in straight as well as coil form.
Installation :
Joint preparation must be done as specified in the installation
instructions. Pipe outside surface must be scraped to remove oxidized
layer. Before fusing, pipe ends and inside of the fittings must be
cleaned to remove dirt and contamination. Complete Installation
Manual may be downloaded.
Standards:
• PE Pipe Compatibility : ISO:4427, ISO:4437, EN:1555-2, EN:
12201-2, IS: 4984, DIN:8074
• Complies with EN1555- Part 3 for Gas, EN12201- Part 3 for water
For details about our other products and specifications please refer the corporate websiteDisclamer : Kimplas reserve the right to modify product without prior notice, as part of its continual improvement programme. Whilst every effort is taken to
ensure the accuracy of information contained in the data Sheet, Kimplas accepts no liability for matters arising as a result of errors or omissions.
GW-Rev
02/July�17
GIS/PL-4:2014KM 518050
TM
20
25
32
40
50
55
63
75
90
110
44
53
68
67
133
117
133
221
496
799
31
36
44
53
65
69
81
91
113
138
70
70
75
75
90
85
100
100
133
152
22
28
42
52
55
40
70
80
140
160
4
4
4
7
7
7
7
7
15
15
C20BKB
C25BKB
C32BKB
C40BKB
C50BKB
C55BKB
C63BKB
C75BKB
C90BKB
C110BKB
250
175
150
125
60
50
35
35
14
11
140
160
180
200
225
250
280
315
240
380
400
480
690
840
650
840
20
20
20
30
30
40
40
40
170
193
215
246
277
292
342
386
165
180
190
183
212
212
220
274
1217
1585
2000
2270
3500
4500
5800
8030
C140BKB
C160BKB
C180BKB
C200BKB
C225BKBN
C250BKBN
C280BKBN
C315BKBN
7
12
9
6
4
4
2
2
C20BKA
C25BKA
C32BKA
C40BKA
C50BKA
C55BKA
C63BKA
C75BKA
C90BKA
C110BKA
C140BKA
C160BKA
C180BKA
C200BKA
C225BKAN
C250BKAN
C280BKAN
C315BKAN
125 885 152 167 220 15C125BKF 7C125BKAF
Recommended
