ZX 32 / ZX 32T / ZX32 3F USER MANUAL - Tanning-Bed-Parts.com Tan Documentation/M… · 22678C i Limited Lifetime Warranty SunStar® warrants your tanning unit to be free of structural

ZX 32 / ZX 32T / ZX32 3F

USER MANUAL 22678C

22678C

i

Limited Lifetime Warranty

SunStar® warrants your tanning unit to be free of structural defects in its material andworkmanship, under normal use, for its lifetime. SunStar will repair or replace, at their dis-

cretion, any defect to the structure which affects the performance of the unit.

For 6 months from the date of purchase, SunStar will provide replacements for parts thatprove to be defective in material or workmanship. Acrylic shields, fluorescent lamps, and

lamp starters are excluded from this warranty. Labor will be covered for 30 days from pur-chase date. Normal wear, damage from misuse or abuse, damage incurred in transit, or

damage done by unauthorized repairs or modifications are not covered by this warranty.

ETS, Inc. disclaims any implied warranty of merchantability or fitness for any periodbeyond the expressed warranty. Some states do not allow limitations on how long an

implied warranty lasts, so the above limitations may not apply to you.

No one has authority to change or modify this Limited Lifetime Warranty in any respect. Toobtain service under the Limited Lifetime Warranty, contact ETS, Inc. at 1-800-449-3605,

and ask for the Technical Service Department.

ETS, Inc. shall not be liable for loss of use, loss of time , inconvenience, rental or substituteproducts, loss of business, loss of income, or any other incidental or consequential damages.Some states do not allow the exclusion or limitation of incidental or consequential damages,

so the above limitation or exclusion may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights which mayvary from state to state.

All warranty service must be performed by an authorized service person. If your tanningunit must be returned for service, all freight charges must be at your expense. Contact yourplace of purchase for the address of the SunStar Service Center nearest you. Proof of pur-

chase is required to obtain warranty service.

This warranty covers the original purchaser only. This warranty is void if the unit is modi-fied in any manner from its original design.

2267

8C ii

elcomeCongratulations on your purchase of this technologically advanced sun tanning unit. It has beendesigned to provide years of dependable service for you.

Please read all the instructions in this booklet before installing and using the unit. Always be sure toobserve all safety precautions.

ontentsSafety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Unpacking and Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2Pre-Installation Planning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Hardware Inventory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4Assembly Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19Remote Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24Before You Tan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24Exposure Times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24Using Your Sunbed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27Cleaning After Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27Thorough Periodic Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . .27Mechanical Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27Lamp and Acrylic Replacement . . . . . . . . . . . . . . . . . . . . . . . . .28

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

22678C

Ultraviolet radiation. Follow instructions. Avoid overexposure. As with natural sunlight, overexposure cancause eye and skin injury and allergic reactions. Repeated exposure may cause premature aging of the skin

and skin cancer. WEAR PROTECTIVE EYEWEAR; FAILURE TO MAY RESULT IN SEVERE BURNS OR LONGTERM INJURY TO THEEYES. Medications or cosmetics may increase your sensitivity to the ultraviolet radiation. Consult physician before using sunlamp ifyou are using medications or have a history of skin problems or believe yourself especially sensitive to sunlight. If you do not tan inthe sun, you are unlikely to tan from the use of this product.

To use, lie down under canopy and pull down as far as adjustment will allow. Minimum use distance from face tanner is 1 inch or 2.54centimeters. Minimum use distance elsewhere is touching the clear plastic panels. Do not use without clear plastic panels in place.Untanned persons should not tan on consecutive days during their first week of tanning. Never tan more than once a day. Tanningnormally appears after the first few sessions and maximizes after approximately four weeks. Tan once or twice per week thereafter tomaintain appearance. Persons already having a base tan may begin at advanced levels corresponding to the extent of their base tan.

New lamps emit approximately 20% more ultraviolet radiation during the first 50 hours of operation. Recommended tanning timesshould therefore be reduced by approximately 20% during that period.

WARNING: • Read the instructions booklet before using this sunlamp product. • All persons in the room should wear protectiveeyewear when lamps are on. Recommended eyewear: provided eyeshields (Lucas Products Super Sunnies or Intrexco No. 5635/1) orequivalent eyewear as defined under 21 CFR 1040.20. Other types of eyewear may not provide adequate protection.

ONLY THE FOLLOWING LAMPS HAVE BEEN CERTIFIED FOR USE IN THIS EQUIPMENT:Model ZX32: SPEED 175™ Wolff® Model SPD75-T12 Bi-Pin

Model ZX32T: SPEED 175™ Wolff® Model SPD75-T12 Bi-PinTurbo Sun™ S Wolff® Model F8-T5-10W

Model ZX32 3F: SPEED 175™ Wolff® Model SPD75-T12 Bi-PinPhilips Model HPA 400/30s or CosmoTech Model 23045 or 20046 (facial unit)

THIS EQUIPMENT MUST BE EARTH GROUNDED.

THIS PRODUCT IS IN CONFORMITY WITH PERFORMANCE STANDARDS FOR SUN LAMP PRODUCTS UNDER 21 CFR PART1040.20

iii

afety InformationLABELING NOTICE: Labels are affixed on all systems to inform the user of possible dangers. Regulations are stated in 21 CFR, Section1040.20, and require that all products manufactured after September 8, 1986 which use sunlamps must display the following:

DANGER

RECOMMENDED EXPOSURE TIMES IN MINUTES MAXIMUM EXPOSURE TIME IS 20 MINUTESLevel 1/Week 1 Level 2 Level 3 Level 4 Subsequent

Skin Type: 1st-3rd Sessions MaximumI Sensitive Skin (Burns easily and severely and does not tan.) NOT RECOMMENDED FOR TANNINGII Light (Burns easily and severely and tans minimally.) 4 8 12 16 20III Normal (Burns moderately and tans average.) 6 10 15 20 20IV Dark (Burns minimally, tans easily and above average.) 8 12 16 20 20

DISCONNECT POWER CORD BEFORE ATTEMPTING TO CLEAN, RELAMP, OR ENGAGE IN THE MAINTENANCE OF THIS PRODUCT.

2267

8C 1

nstallation

Unpacking and Inspection

Your sunbed comes in two cardboard car-tons, one for the bench and one for thecanopy. Open the cartons and remove thebench and canopy as follows.

The bench and canopy are each wrappedin plastic. Pull back the plastic and, witha helper, grasp the bench and pull it fromthe carton bottom, leaving the plasticwrap and the carton packaging. Do thesame for the canopy. Do not attempt tolift either unit with the plastic still on asit may slip.

Note! The cartons are reusable, in theunlikely event that you may find it neces-sary to return your sunbed.

After unpacking the unit, check to makesure you have received the following:

• Canopy unit• Bench unit• Ballast tray• Pair of gas springs• Opening handle• Box containing front and side skirts

with mounting screws• Bag containing necessary assembly

hardware, remote bypass, safety gog-gles, and pillow

• Box containing two stand legs, twocross member supports and four skirtmounting brackets

• Gas spring cover panel

Inspect these items, including the canopyand bench, and make sure they are freefrom any visible damage. Report theextent of any damage to the transportationcompany.

Record the serial numbers of the canopyand bench in the area provided on theback of this manual. This information willbe required whenever you call customerservice.

22678C

2

Installation - Tools Required

Tools RequiredYou will need the following tools to assemble your sunbed.

Utility Knife

#2 Phillips Screwdriver

Allen Wrench(Supplied in hardware kit)

Open-ended wrench(Supplied in hardware kit)

#2 Flat-bladed Screwdriver

2267

8C 3

Installation - Pre-Installation Planning

Pre-Installation PlanningBefore you begin to assemble your sunbed, you should observe the following consid-erations.

• Your sunbed operates from a 220VAC power source. The unit should bewired to a dedicated circuit asdescribed below. We recommendconnection by a professional electri-cian.

• IMPORTANT! Voltage must bebelow 230V AC or may require aBuck Booster. Contact ETS service atthe number on the back of thisguide. Use of a voltage source above230V AC may reduce the life ofsome components in your sunbed.

• The SunStar® Super ZX32 Speed 175System™ requires a dedicated circuitcapable of providing 30 Amp service.This unit must be hardwired directlyto a junction box.

• Make sure the room in which youintend to use your sunbed is wellventilated. Air from the room is usedto cool the sunbed, and a poorlyventilated room may cause the unitto become hot and cause discomfortto the user.

• Your sunbed is designed to operatein an ambient room temperature of80°F maximum and 70% relativehumidity.

• Place your sunbed no closer than 6"from any wall. Make sure that cur-tains, drapes, and other room furni-ture do not obstruct the airflow intothe end caps or out of the fan open-ing areas.

• Proper assembly of your sunbedrequires three people. Plan to have acouple of helpers assist you.

22678C

Carriage Bolt,M10 x 60mm

Quantity 2

Self-locking Nut, M10Quantity 2

Hex Socket Head Bolt,M8 x 80mm

Quantity 4

Hex Socket Head Bolt,M8 x 60mm

Quantity 2

Self-locking Nut, M8Quantity 2

Plastic Trim CapQuantity 4

4

Installation - Hardware Inventory

Hardware Inventory

Use the utility knife to cut open the hard-ware bag and blister pack. Remove thehardware. Make sure you have the follow-ing hardware items.

Hex Socket HeadBolt, M8 x 20mm

Quantity 8

Flat Washer, M8Quantity 12

Foot CapsQuantity 4

Clevis Fork,M10 LongQuantity 4

Plastic Spacer, 15mmQuantity 4

2267

8C 5


Plastic Trim WasherQuantity 4

Nylon FloatingBearing

Quantity 4

Clevis Pin, 10mmQuantity 2

Retaining RingQuantity 2

Bronze Bushing, 10mmQuantity 2

Phillips Head Screw,#10 x 1/2”

Quantity 20

Phillips Pan Type AB Screw, #10 x 1”

Quantity 3

Rubber Leg CapQuantity 2

Hex Key (Allen Wrench), 6mm

Quantity 1

Open End Wrench, 13mm/17mm

Quantity 1

Skirt Latch KeyQuantity 1

22678C

6


Remote Control Bypass PlugQuantity 1

Safety GogglesQuantity 1

2267

8C 7

Installation - Assembly Procedures

Assembly Procedures

Stand Assembly1. Fit the cross member supports (A) to

the stand legs (B) using the M8 x20mm bolts (C) and the M8 washers(D). Assemble the bolts a few turnsonly.

2. After the stand is assembled, tightenall bolts.

Tip: The rectangular hole on the outside ofthe stand leg channel is for Allen wrenchaccess. Insert the Allen wrench into theoutside rectangular hole. Next slide thewasher onto the bolt and the bolt onto theAllen wrench inside the stand channel.

22678C

8


3. Place the foot caps (B) under the standlegs (A) and position the stand in theapproximate spot you want thesunbed.

2267

8C 9


4. Attach the four skirt mounting bracketsto each corner of the stand legs, usingeight #10 x 1/2” Phillips head screws.Each location is predrilled to accept abracket. You will notice that there aretwo types of brackets. The rear brack-ets are simply “L” shaped, while thefront brackets have a rectangular holeand a slight step.

22678C

10


5. Assemble the lower clevis forks (A) inthe stand using the 15mm spacers (B),the M10 x 60mm carriage bolts (C)and the M10 self-locking nuts (D).When assembled the threaded hole inthe clevis fork should point upwards.

2267

8C 11


Attaching Bench to Stand1. Place the sunbed bench carefully on

the stand and fasten in position usingthe M8 x 80mm bolts (A) and the M8washers (B). Position the bench withthe electrical connector toward theback.

Tip: Fasten only one bolt on each endbefore inserting the other two.

22678C

12


Attaching Canopy to Stand1. You may find it easier to attach the

canopy to the stand if you have spacerswhich span the width of the bench.Two 36” pieces of 2”x4” framing lum-ber work well for this purpose. Usethese spacers to support the canopyduring the next few steps. (See figure 1)

2. Lift the canopy assembly onto thebench (or spacers if you have them)with the arms (A) toward the back.

3. Insert the nylon floating bearings (C)into the canopy assembly arm (A).Attach the arm (A) to the stand legs (B)using the M8 x 60mm bolts (D), theplastic trim washers (F) and the M8self-locking nuts (E).

NOTE: The plastic trim washers (F) have aridge to engage the plastic caps (G). Thisridge must face away from the stand legsto engage properly.

4. Press the plastic trim caps (G) over thebolt heads and self-locking nuts. Theyshould snap onto the plastic trimwashers (F).

FIGURE 1

2267

8C 13


Canopy body not shown for clarity

22678C

14


5. Lift the canopy assembly to its fullyopen position and have two helpershold it.

6. Screw the rod end of the gas springs(A) into the lower clevis forks previ-ously attached to the stand legs. Screwthe other clevis forks (B) to the pistonend of the gas springs (A).

7. Now insert the bronze bushings (C)into the clevis bracket holes. Line upboth clevis forks (B) and lower thecanopy until the clevis forks (B)engage the bushings (C) and attachwith the clevis pins (D) and retainingrings (E). Pay special attention whenlowering the canopy that the clevisforks do not damage the bronze bush-ings. Bronze is excellent for smoothpivoting applications such as this, buttends to be a soft metal compared tothe steel clevis fork.

NOTE: When this assembly is complete,lift and lower the canopy a few times tolubricate the gas springs for optimum per-formance.

2267

8C 15


CLEVIS BRACKET

(Canopy body removed for clarity.)

22678C

16


Attaching Handle to Canopy1. Install the handle by inserting the three

#10 x 1” Phillips head screws throughthe handle and into the predrilledholes on the canopy.

2. Press the rubber leg caps on the standlegs.

2267

8C 17


Attaching the Skirt1. Place the side skirts against the two

skirt mounting brackets at each end ofthe sunbed. Using eight #10 x 1/2”screws, attach the side skirts to theskirt mounting brackets. It is best notto tighten the screws until all areinstalled.

2. Place the ballast tray under thesunbed, with the power cords towardthe rear of the unit as shown.

(Sunbed removed for clarity.)

22678C

18

Installation - Electrical Connections

Electrical ConnectionsAt the rear of the sunbed, connect the twocanopy power cords and two bench powercords from the ballast tray to their respectivepower receptacles. Simply match the plugto the receptacle, push on firmly and secureby twisting the threaded locking ring.Connect the Remote Control Bypass plug toeither remote control port. Your sunbed willnot operate without the Remote ControlBypass plug or a remote system connected.Connect main power cord as described inPre-Installation Planning.

NOTE: Your sunbed is designed to accept aninput from a remote control device. Theremote control is optional. If you plan on usinga remote system refer to Remote Connections.

ATTENTION: Although the Remote ControlBypass plug provided with your sunbed willwork wherever a T-Max® terminator is calledfor in the series, the T-Max® terminator willnot work as a bypass plug. Normally, a bypassplug is needed only when your sunbed is oper-ated without a remote system connected.

REAR OF BALLAST TRAY

CANOPY POWER RECEPTACLES

BENCH POWER RECEPTACLES

MAIN POWER CORD

RemoteControl Bypass

plug

Remote Ports

2267

8C 19

Installation - Final Assembly

2. If not already done, position the bal-last tray filter as shown.

3. Position the front skirt against the twobrackets on the front of the stand.There is a slot in the underside of thebench that the front skirt is designed tofit into. Center the front skirt and usethe skirt latch key to lock the skirt in

place. Remove the protectivefilm from the acrylic shield.Your equipment is nowready for use.

Final Assembly

1. Install the gas spring cover onto thestand legs, as shown. Secure usingfour #10 x 1/2” screws.

Install screws here

(Sunbed removed for clarity.)

BALLAST TRAY FILTER

22678C

20

Body Fan Assembly (body fan sold separately)

WARNING! Make sure unit is not con-nected to any power source beforeattaching body fan.

Your sunbed is designed to accept a bodycooling fan on the foot end canopy end-cap. Follow the instructions that comewith the body fan for installation.

CENTER INSERT

Installation - Final Assembly

2267

8C 21

Installation - Remote Connections

Remote Connections

Your sunbed incorporates advanced circuitryallowing it to connect and communicate withmost remote control systems. If a remote sys-tem is to be used, first determine whether theremote system is a T-Max® System or a stan-dard remote system operating with a controlrelay. Follow the appropriate instructions foryour system type.

Warning: The remote connection is notdesigned to supply or accept high voltage, norcan it provide power to an external timer. Thesunbed’s remote interface circuitry operateson 5 volts, attempting to connect it to anyhigher voltages will damage the sunbed aswell as void your warranty.

T-Max® ProductsThe T-Max® remote systems offer the ultimatein sunbed control, while allowing the tannereasy straightforward operation. Your sunbed isconfigured to directly connect to this system.The circuitry inside your sunbed eliminates theneed for the T-Max® 1A or 3A when connect-ing to the T-Max® Manager series. Yoursunbed supports the auto addressing feature ofthe latest T-Max® Manager models and the fol-lowing parameters: 2, 5, 6, 7, 8, 9, 10, 14, and15. See your T-Max® manual for descriptionsof these parameters and how they function.

T-Max® Manager Remote System This system is ideal for multiple sunbed instal-lations. Simply connect the RJ-22 modularcable(s), described in the T-Max® Managermanual, into the remote port(s) located on theback of your sunbed and follow the instruc-

tions that came with your remote sys-tem, noting figure 1. If you have anolder T-Max® Manager that doesn’tsupport auto addressing, set theaddress, or “id”, of each sunbed man-ually as described in Setting theaddress manually. You can place yoursunbed at any location in the series.

figure 1

NOTE: A T-Max® 1Acan be substituted for

the 3A in figure 1.

22678C

22


T-Max® 1A and 3A Remote SystemsThe T-Max® 1A and 3A offer the same controlas the T-Max® Manager in single sunbed instal-lations. If you’re using a 1A, it must have a chiplabelled “master” installed on its circuit board.The remote control bypass plug must not beused in this configuration.

After you have set the T-Max® 1A’s, or 3A’s,address to “0” (refer to your T-Max® user’sguide) and the sunbed’s address to “1” (seeright), simply connect the RJ-22 modularcables, described in the T-Max® user’s guide,directly into either port located on the back ofthe sunbed and either port on the back of theT-Max® 1A or 3A. See figure 2.

Setting the address manuallyBefore connecting your sunbed to the T-Max®Manager or T-Max® 1A or 3A, the address ofyour sunbed must first be set. Set the “id” man-ually as described below.

Setting the “id” 1. Make sure no cables are plugged into

your sunbed’s remote ports.2. Remove and reapply power to the unit.3. Press and hold the stop button, located

on the sunbed display, for three secondsand release. The display should indicatean “id” number from “oF” to “252”.

4. If you are using a T-Max® 1A or 3A asyour remote, the “id” of the sunbedmust be set to “1”. If you are using a T-Max® Manager each sunbed must beassigned a different “id”. To set the “id”press the timer button, to count up, orthe body fan control button, to countdown, until the desired number isachieved.

5. Press the stop button to return to thenormal display mode.

1-99

100-199

200-252

figure 2

NOTE: A T-Max® 1Awith a “master” chipcan be substituted for

a 3A in figure 2.

2267

8C 23

figure 3

Remote systems using a Control Relay

Most non-T-Max® remote systems control thesunbed by the use of a relay. The relay oper-ates the sunbed by connecting and discon-necting a pair of wires leading from thesunbed. Refer to the user’s manual providedwith your remote system to determine if itoperates in this way. To connect your sunbedto this type of system a remote interface kit isrequired. Call ETS at the phone number listedon the back of this guide to obtain the kit.Figure 3 details a typical connection. Followthe instructions provided with the kit andfrom the remote’s manual to make the neces-sary connections.


22678C

24

peration

Before You Tan

Before using your sunbed, please note thefollowing important precautions.

• Your skin should be free of cosmetics,tanning oils, or other body lotionsprior to tanning except for thosespecifically made for use with tanningdevices. However, do not remove nat-ural body oils by bathing or showeringimmediately before tanning.

• Your hair should be free of gels,mousses, sprays, or other hair productsprior to tanning. These products cancause damage to the sunbed acrylic.As an alternative, a shower cap ortowel can be worn to keep treated hairaway from the sunbed surfaces.

• As with all electrical appliances, donot operate this device near water orwhile you are wet.

RECOMMENDED EXPOSURE TIMES IN MINUTES MAXIMUM EXPOSURE TIME IS 20 MINUTESLevel 1/Week 1 Level 2 Level 3 Level 4 Subsequent

Skin Type: 1st-3rd Sessions MaximumI Sensitive Skin (Burns easily and severely and does not tan.) NOT RECOMMENDED FOR TANNINGII Light (Burns easily and severely and tans minimally.) 4 8 12 16 20III Normal (Burns moderately and tans average.) 6 10 15 20 20IV Dark (Burns minimally, tans easily and above average.) 8 12 16 20 20

• Some medication may increase yoursensitivity to ultraviolet light. It is rec-ommended that you consult a physi-cian before using this sunbed if takingany medication or if you suspect thatyour skin might be especially sensitiveto sunlight. Included with this manualis an FDA booklet on medications thatincrease sensitivity to light.

Exposure Times

Follow the guidelines for skin type andexposure times as shown in the tablebelow. Untanned persons should not tanon consecutive days during their first weekof tanning. Never tan more than once aday. Tanning normally appears after the firstfew sessions and maximizes after approxi-mately four weeks. Tan once or twice perweek thereafter to maintain appearance.Persons already having a base tan maybegin at advanced levels corresponding tothe extent of their base tan.

2267

8C 25

2. Put on your safety goggles.

3. Assuming the remote system has been setto allow a pre-tanning delay time, the timerdisplay (E) will repeatedly flash the delaysymbol “dL” and then the remaining delaytime. Press the timer button (G) or waituntil the delay time has expired to beginthe tanning session. The lamps will turn onand the timer will begin to count down.

4. When the timer reaches 0 the lamps turnoff. If you want to stop your session beforetime expires, press the stop button (F).

5. Raise the canopy by using the outer edgeof the canopy, do not push up on theacrylic shield. The cooling fans run forthree minutes after the lamps shut off toaid in cooling the sunbed. The timer willindicate “..” as a reminder to clean thesunbed. After the sunbed is cleaned pressthe timer button and the display willreturn to “0”.

Operation - Using Your Sunbed

Using Your SunbedWhen connected to the T-Max® Manager or T-Max® 1A or 3A.

A Face tanner control - Turns face tannerson and off during use. (Units equippedwith face tanner only)

B Body tanner control - Turns body lampson and off during use. (Units equippedwith face tanner only)

C Body fan control - Controls the speed ofthe body fan during use.

D Body fan speed indicator - Indicatesspeed of fan. (OFF - LOW - MED -HIGH)

E Timer display - Displays remaining time.

F Stop button - Interrupts tanning session.

G Timer button - Turns bed on.

A B C D E F G

1. Lift the canopy, lie down on the bench(face up), lower the canopy toward yourbody using the canopy handle. For bestresults, position the canopy as close toyour body as possible.

22678C

26

Operation - Using Your Sunbed

Using Your SunbedWhen used as a stand alone unit or when connected to a remote system using a control relay.

1. Lift the canopy, lie down on the bench(face up), lower the canopy toward yourbody using the canopy handle. For bestresults, position the canopy as close toyour body as possible.

2. Put on your safety goggles.

3. Press the timer button (G) to begin the tan-ning session. The lamps will turn on andthe timer will begin to count down.

4. If a tanning time less than the displayedtime is desired repeatedly press the timerbutton (G) to decrease the remaining time.

5. When the timer reaches 0 the lamps turnoff. If you want to stop your session beforetime expires, press the stop button (F). Youwill have ten seconds to restart with theremaining time, otherwise the timer willreset to 0.

6. Raise the canopy by using the outer edgeof the canopy, do not push up on theacrylic shield. The cooling fans run forthree minutes after the lamps shut off toaid in cooling the sunbed.

A B C D E F G

A Face tanner control - Turns face tannerson and off during use. (Units equippedwith face tanner only)

B Body tanner control - Turns body lampson and off during use. (Units equippedwith face tanner only)

C Body fan control - Controls the speed ofthe body fan during use.

D Body fan speed indicator - Indicatesspeed of fan. (OFF - LOW - MED -HIGH)

E Timer display - Displays remaining time.

F Stop button - Stops tanning session.

G Timer button - Turns bed on. Timer dis-play shows remaining time. If a lessertime is desired, press timer button untildesired time is displayed.

2267

8C 27

are and Maintenance

Cleaning After Use

Clean and disinfect your tanning bed’sbench and canopy after each use. Use anon-abrasive disinfectant cleaner that doesnot contain ammonia or ammonia deriva-tives. Ammonia may damage the acrylicshield. Spray the acrylic lightly with disin-fectant and wipe dry with a clean soft cloth.We recommend SunQuest® disinfectant andSunQuest® acrylic cleaner.

Thorough Periodic Cleaning

IntroductionThe cooling fans draw air through the bedand over time will cause a dust buildup onthe lamps and reflectors. This will reducethe tanning effectiveness of the bed. Whena dust buildup is observed, it is necessary tothoroughly clean the inside of the benchand canopy. Warning! Disconnect sunbedfrom electrical power before cleaning.

Cleaning the Canopy and BenchStep 1 Remove the acrylic shields and

lamps as described in Lamp andAcrylic Replacement.

Step 2 With a soft cloth, wipe the entirelength of each lamp to removeany film buildup.

Step 3 Clean both sides of the acrylicshields with a non-ammonia dis-infectant cleaner.

Step 4 Wipe the reflectors with a cleandamp cloth.

Step 5 Reinstall the lamps and acrylicshields.

Step 6 Clean or replace air filter on topof ballast tray. Replace with a 10”x 24” x 1” furnace filter.

Mechanical Inspection

Your tanning bed has been built for years ofservice. To ensure trouble-free operationthroughout its life, inspect the unit’smechanical integrity every 400-500 hoursof use.

• Inspect the unit’s fasteners verifyingthat all are firmly in place.

• Inspect gas springs for signs of wear.Gas springs that will not hold thecanopy in the full open position whenraised should be immediately replaced.See Troubleshooting.

• Inspect the AC power cord and itsconnections.

• Inspect the acrylic. Broken, cracked orbadly scratched acrylics should beimmediately replaced.

22678C

28

Care and Maintenance - Lamp and Acrylic Replacement

Lamp and Acrylic Replacement

IntroductionTo be assured of maximum tanning effec-tiveness, change lamps after approximate-ly 800-1000 hours of use. Tanning willcontinue after this time but at a slowerrate. To ensure trouble-free operation ofyour sunbed, replace the lamp starterswhenever the lamps are replaced.

Warning! Disconnect sunbed from elec-trical power before servicing.

Removing/Replacing Acrylic ShieldThe acrylic shields in the bench andcanopy are secured in place by hingedprofiles which run the length of the bed,both front and back. Simply pry up on theinside edge of the profile, starting at thecenter of the bed, until it releases its latch-ing action (see figure at right). Continue topry up the profile across its entire lengthuntil it swings back freely. Repeat for theother profile. The long edges of the acrylicshields are now exposed.

Standing at the front of the unit, lift theexposed edge of the acrylic slightly andcarefully begin sliding it toward you untilit is removed from the sunbed. This mightbe easier with the help of another person.

After changing the lamps, replace theacrylic shield by carefully aligning it withthe channels on the ends of the sunbedand sliding it into place. Close the hingedprofile by pushing it back into place untilit snaps tight.

Be careful. The edges of the acrylicshield may be sharp.

NOTE!

Start pulling from thecenter of the bed!

2267

8C 29


Removing/Replacing LampsAfter removing the acrylic shield, replacelamps as follows.

Step 1 Grasp the lamp at one end andat the middle and turn the lampone quarter turn. Gently removethe lamp from its holders.

Step 2 Reinstall the lamp by insertingthe pins located on the ends ofthe lamp into the slots on top ofthe lamp holders and turn thelamp a quarter turn. It shouldclick in place.

Recommended Replacement LampsWe recommend using the lamps specifiedbelow. Use of uncertified lamps is a viola-tion of Federal regulations and will voidyour warranty. These lamps have an aver-age life of 800-1000 hours of effectivetanning use. Lamps used longer than thatbegin to lose their effectiveness eventhough they continue to light.

Recommended Replacement AcrylicsAcrylics vary greatly over time in theirability to effectively transmit UV light.Acrylics sold by ETS have been life testedto ensure proper transmission throughouttheir useful life.

ONLY THE FOLLOWING LAMPS HAVE BEEN CERTIFIED FOR USE IN THIS EQUIPMENT:Model ZX32: SPEED 175™ Wolff® Model SPD75-T12 Bi-Pin

Model ZX32T: SPEED 175™ Wolff® Model SPD75-T12 Bi-PinTurbo Sun™ S Wolff® Model F8-T5-10W

Model ZX32 3F: SPEED 175™ Wolff® Model SPD75-T12 Bi-PinPhilips Model HPA 400/30s or CosmoTech Model 23045 or 20046 (facial unit)

22678C

30


Removing/Replacing Face TannerLamp on F Models

After removing the canopy acrylic shield,replace the face tanner lamp as follows:

Step 1 Support the face tanner assemblywith your hand while unscrew-ing the two retaining screws. Theface tanner glass casing willswing downward.

Step 2 The lamp can now beexchanged. The lamp holdersare equipped with spring con-tacts which enable the lamp tobe removed easily. Remove theold lamp and discard. Install thenew lamp, using a clean clothor paper towel. Ensure that thelamp is firmly seated in thelamp holders.

Note! Never take hold of the lamp suchthat your fingers are in contact with thelamp glass. Finger oils will greatly reducethe lamp’s operational life.

Step 3 Gently close the face tannerglass casing and lock it closedwith the screws. Ensure that thescrews firmly secure the glasscasing.

RETAININGSCREWS

Never turn the equipment on while theface tanner is disassembled or when theglass filters have been removed. Thedirect light can cause severe injury to theeyes and other areas of the body.Immediately discontinue use of thisequipment if the face tanner glass is bro-ken or if any unfiltered light can be seenescaping the face tanner assembly.

WARNING!

2267

8C 31

roubleshooting

Problem SolutionSunbed not tanning

Lamps fail to light and timer dis-play is blank

Timer display changes to indicatea tanning time after the timer but-ton is pressed but lamps do notcome on

My bed is connected to the T-Max® Manager remote system andwhen the delay time has expiredthe timer display starts countingdown but the bed lights do notcome on

My bed won’t work with the T-Max® Manager remote system

Timer display continues to show a0 after the timer button is pressed

The last minute of tanning timedoes not count down from 59 sec-onds, but some time less than 59seconds

1. Clean sunbed, see Thorough Periodic Cleaning.2. Ensure supply voltage is between 208 and 230V AC.3. Replace lamps if lamp hours are greater than 800hrs.4. Replace acrylic.

1. Make sure the unit is connected to a power source.2. Check source of AC power. Reset circuit breaker or replace fuse.

1. Bypass plug is not installed, see Electrical Connections.2. A non-SunStar® bypass has been used. See Electrical

Connections.3. If remote is being used, other than T-Max® Manager, the

external timer may not be activated.4. Remote wiring is incorrect, see the instructions provided with

the remote interface kit.

The auto start feature of the remote system is disabled, see theinstructions provided with your remote system.

1. The sunbed must first be set to a unique address, see RemoteConnections.

2. The bypass or terminator plug may be installed in the series inan inappropriate location. Plug the bypass plug only into thebed at the end of the series.

1. T-Max® Manager remote system has not yet been set. 2. Sunbed address is not set correctly, see Remote Connections.

If the timer button has been pressed to decrease tanning timeduring the session, the time expired in the current minute issubtracted from the last minute.

22678C

32

Problem SolutionOne or more lamps fail to light

The face tanners will not come on

The canopy will not stay up

My bed is connected to a T-Max®remote system but I am havingtrouble getting into “id” mode

My bed, connected to a T-Max®Manager, did not display “dL” butdoes indicate:

“0”

a tanning time and the lampshave come ona tanning time but the lampshave not come on

Timer display is indicating Er 1


1. Check that lamp is installed correctly.2. Switch unlit lamp with a lamp that lights, if new lamp lights

and old lamp still does not, replace old lamp.

1. Face tanner operation is initially delayed by 5 seconds.2. Face tanners will not relight until cooled.3. Replace face tanner lamp, see Removing/Replacing Face

Tanner Lamp on F Models.

NOTE: Gas springs are manufactured to hold the canopy in itsfully open position as well as allow it to rest fully closed. If leftopen for an extended period of time some creep down mayoccur. This is considered normal. Keep the unit closed whennot in use. If the canopy will not stay fully open when raised...

1. Raise and lower the canopy a few times to lubricate gas springinternal seals.

2. Replace gas springs.

You have probably attempted to connect your sunbed to theremote system already. Disconnect the remote plug(s) from theports at the back of the sunbed, wait 90 seconds and try again.

1. Remote device has not been set.2. The sunbed has not been connected to the remote system, see

Remote Connections.1. Delay time of T-Max® Manager has not been set.2. Delay time has expired and session has begun.

Auto start function of T-Max® Manager has been turned off.Press the timer button to turn on lamps.

Body lamps are on when they should be off, have servicetechnician check the contactor.

Body lamps are off when they should be on, have service tech-nician check contactor and its wiring from the main timer box.

2267

8C 33

Problem SolutionTimer display is indicating Er 3













Bench lamps are on when they should be off, have servicetechnician check the contactor. (Units with separate benchcontactor only.)

Bench lamps are off when they should be on, have servicetechnician check the contactor and its wiring from the maintimer box. (Units with separate bench contactor only.)

Not currently used

Not currently used

Face Tanner contactor is closed when it should be open, haveservice technician check the contactor.

Face Tanner contactor is open when it should be closed, haveservice technician check the contactor and its wiring from themain timer box.

Ballast Drawer is open or drawer switch is broken.

Timer computer is in an illegal state, reset power to correct,replace main timer if error reoccurs.




The timer display is not responding;1. Check cable to display.2. Replace display assembly.3. Replace main timer box.


22678C

Problem SolutionWhen auto-addressing the firstbed does not register an “id”

When using a T-Max® 1A mysunbed won’t function properly

I forgot what address, or “id”, I setmy sunbed to

When using the auto address feature of the T-Max® Manageryou must wait 10 seconds from the time you start the autoaddress function before addressing the first bed.

SunStar® Bypass plugs or terminator plugs may be needed ifthe T-Max® 1A and the sunbed are over 100 feet apart. Installthe plugs in the open remote port in the sunbed and the T-Max® 1A.

By holding the body fan button for 3 seconds the timer displaywill briefly display three numbers; the installed timer softwareversion, a factory set timer code and then the sunbed’s “id”number.

34

2267

8C

ZX

32

22678C

ZX

32T

2267

8C

ZX

32 3

F

22678C

Bal

last

Tra

y

2267

8C

Parts List(When calling for parts, first state your bed model asH-ZX32, H-ZX32T or H-ZX32 3F. Then refer to thislist and proper illustration for part identification.)

Acrylic, BenchAcrylic, Canopy*Ballast, SPEED 175™Ballast, Face Tanner 400WBallast, Turbo 30WBushing, Bronze 10mm*Body Fan Kit* (optional)Canopy Mounting ArmCapacitor, 75uFContactor (Relay)Contactor for Face TannersCover, BenchCover, CanopyEndcap, Kit (with inserts)Face Tanner Relay (turbo)FanFan RelayFilter*Foot CapGas Spring Cover Panel*Gas Springs*HandleHardware Blister Pack*Hour CounterKeypad Assy KitLamp Holder w/ StarterLamp Holder w/o StarterLamp Holder, Face Tanner*Lamp Holder, TurboLamps*

CALL FOR SERVICE OR QUESTIONS: 1•800•449•3605ETS, Inc. 6270 Corporate Drive, Indianapolis, IN 46278-2900

Record this information for ease of service:

Date of purchase:

Bench serial number:

Canopy serial number:

Ballast tray ID number:

Latch Key for Front Skirt Panel*Leg Stand and Skirt Bracket KitManual*Pillow*ProfileRemote Connection PCBRemote Control Bypass Plug*Schematic Packet*Silk-screened ProfileSkirt KitStarter, K-12 (main lamps)Starter, Face Tanner (ignitor)Starter, S-2 (turbo)Starter Holder, S-2 (turbo)Thermostat* (for face tanner)TimerTrim Profile, (grey) full lengthTrim Profile, (grey) canopy rear middle*Trim Profile, (grey) canopy rear ends*Wiring Harness, Keypad to TimerWiring Harness, Remote PCB to Timer

* Not shown

This sunbed utilizes a proprietary systemof components known as the Speed 175System™. Only certified Speed 175System™ components may be used asreplacements, including lamps and bal-lasts.

CALL FOR SERVICE ORQUESTIONS:

1•800•449•3605

6270 Corporate DriveIndianapolis, IN 46278-2900

Documents

ZX 32 / ZX 32T / ZX32 3F USER MANUAL - Tanning-Bed-Parts.com Tan Documentation/M… · 22678C i Limited Lifetime Warranty SunStar® warrants your tanning unit to be free of structural