VPA 1740 VPA 1750 - Wacker Neusonproducts.wackerneuson.com/manuals/Operators/154574en_001.pdf · Arras 62217 Beaurains Tel. 3 21235361 Bordeaux 33700 Merignac Tel. 5 56343346 Bourges

www.wackergroup.com

Vibroplate

VPA 1740VPA 1750

OPERATOR'S MANUAL

0154574en 001

0602

0 1 5 4 5 7 4 E N

BELGIE1730 ASSE-MOLLEM ASSESTEENWEG 17 Tel. (32) 02-4528509+074040 Herstal 4 Avenue9800 Deinze Kortrijkse Steenweg 400 Tel. (09)-386 8529B - 6041 Gosselies Rue Adrienne Bolland s/n Tel. 071-372450

ÇESKÁ REPUBLIKA19402 PRAHA 9-HLOUBETIN KOLBENOVA 259 Tel. (0042) 2 862165

DANMARK2690 KARLSLUNDE RØRGANGEN 6 Tel. 46 15 36 008200 Arhus N Randersvej 346 Tel. 86-2317775250 Odense SV Holkebjergvej 56A Tel. 66-172170

ESPAÑA28850 TORREJON DE ARDOZ (MADRID) POLIGONO INDUSTRIAL LAS MONJAS Tel. (34) 91-6757525 / 85

CALLE PRIMAVERA 1108780 PALLEJA (Barcelona) PRAT DE LA RIBA, 184 Tel. (93)-663227341700 Dos Hermanas (Sevilla) Poligono Industrial La Palmera Tel. (95)-4691129

Nave 14 Tel. (95)-469112946133 Meliana (Valencia) Calle Salvador Giner, 6 Tel. (96)-149210215890 Santiago de Compostela (La Coruña) Poligono Industrial el Tambre, Via Pasteur, 47a Tel. (981) 573366 / 67

SUOMIFIN 04250 KERAVA Peltomäenkatu 7 Tel. (358) 9-274 4740

FRANCE77170 BRIE COMTE ROBERT 335, RUE GLORIETTE—ZAC DU TUBOEUF Tel. (33) 1-60623000Aix en Provence 13540 Puyricard Tel. 4 42630526Arras 62217 Beaurains Tel. 3 21235361Bordeaux 33700 Merignac Tel. 5 56343346Bourges 18390 St. Germain du Puy Tel. 2 48652015Lyon 69740 Genas Tel. 4 78401384Nancy 54180 Heillecourt Tel. 3 83565801Rennes 35510 Cesson Sevigne Tel. 2 99321522Toulouse 31270 Cugnaux Tel. 5 61075250Kehl 77694 Kehl-Goldscheuer Tel. (0590) 9321

HUNGARIA1106 BUDAPEST Kada u. 137 Tel. (36) 1-260 8668

IRELANDDUBLIN 13 127A. BALDOYLE INDUSTRIAL ESTATE Tel. (00353) 01-8320218

ITALIA40016 SAN GIORGIO DI PIANO (Bologna) Via Due Agosto, 1980, Strage di Bologna, 3 Tel. 39.05.665.566 - 665.157400125 ACILIA (Roma) Viale Enrico Ortolani, 262 Tel. 39 . 06 . 521924620041 Agrate Brianza (Mi) Via Archimede, 31 Tel. 39. 039.699 0136

NEDERLAND3821 BJ AMERSFOORT COBOLWEG 1 Tel. 033 - 450 40 452984 BL Ridderker Glasblazerstraat 7 Tel. 0180 - 41 70 567418 EZ Deventer Arnbergstraat 9 Tel. 0570 - 63 00 875684 PS Best De Dintel 37 Tel. 0499 - 33 04 331704 RT Heerhugowaard Einsteinstraat 4d Tel. 072 - 574 20 789411 XN Beilen De Hanekampen 19 Tel. 0593 - 52 31 24

NORGE1481 HAGAN TYRIVN. 7 Tel. (47) 0 6707-2330

POLSKA05�850 OŻARÓW MAZOWIECKI UL. KONOTOPSKA 4 Tel. (48) 22 722 20 5962�081 Wysogotowo k. Poznania ul. Kamienna 1 Tel. (061) 814�3797

PORTUGAL2785-S. Domingos De Rana Urbanização Industrial de Trajouce, Lote 1 Tel. (351) 21 4443561 / 874785-S. Romao do Coronado Lg. do Soeiro, Apartado 2 Tel. (351) 22 982 7992 / 93

SVERIGE24734 SÖDRA SANDBY SKATTEBERGAVÄGEN 13 Tel. (46) 046-5787016170 Bromma Karlsbodavägen 17E Tel. 08-28286041749 Göteborg Knipplekullen 3A Tel. 031-551362

SCHWEIZ8305 Dietlikon Bahnhofstrasse 3 Tel. (41) 1-8353939

TURKIYE81120 K. Bakkalköy-ISTANBUL Karaman Çiftligi Cad. No: 55 Tel. (90) 216 573 062135350 Üçkuyular-Izmir Mithatpasa Cad. No. 1189 Tel. (90) 232 259 8944Ostim 06370 Ankara Alinteri Bulvari No. 210 Tel. (90) 312 385 6438/6439

VPA Table of Contents

1. Foreword 3

2. Safety Information 4

2.1 Laws Pertaining to Spark Arresters ...................................................... 4

2.2 Operating Safety .................................................................................. 5

2.3 Operator Safety while using Internal Combustion Engines .................. 6

2.4 Service Safety ...................................................................................... 7

2.5 Label Locations .................................................................................... 8

2.6 Warning and Informational Labels ........................................................ 9

2.7 Operating Labels ................................................................................ 12

3. Technical Data 14

3.1 Engine Data ........................................................................................ 14

3.2 Machine Data ..................................................................................... 15

3.3 Sound and Vibration Specifications .................................................... 15

3.4 Dimensions ......................................................................................... 16

4. Operation 17

4.1 Recommended Fuel ........................................................................... 17

4.2 Before Starting ................................................................................... 17

4.3 To Start ............................................................................................... 17

4.4 To Stop ............................................................................................... 18

4.5 Application .......................................................................................... 18

4.6 Operation ............................................................................................ 19

wc_bo0154574001enTOC.fm 1

Table of Contents VPA

5. Maintenance 20

5.1 Periodic Maintenance Schedule ..........................................................205.2 Cleaning Plate .....................................................................................205.3 Engine Oil ............................................................................................215.4 Air Cleaner ..........................................................................................225.5 Spark Plug ...........................................................................................235.6 Exciter Lubrication ...............................................................................245.7 Drive Belt .............................................................................................255.8 Adjusting Engine Speed ......................................................................265.9 Cleaning Sediment Cup ......................................................................265.10 Carburetor Adjustment ........................................................................275.11 Storage ................................................................................................275.12 Lifting Machine ....................................................................................285.13 Transporting Machine ..........................................................................295.14 Troubleshooting ...................................................................................30

wc_bo0154574001enTOC.fm 2

Foreword

wc_tx000001gb.fm 3

Engine exhaust, some of its constituents, and certain vehiclecomponents contain or emit chemicals known to the State of Californiato cause cancer and birth defects or other reproductive harm.

1. Foreword

This manual provides information and procedures to safely operateand maintain this Wacker model. For your own safety and protectionfrom injury, carefully read, understand and observe the safetyinstructions described in this manual.

Keep this manual or a copy of it with the machine. If you lose thismanual or need an additional copy, please contact WackerCorporation. This machine is built with user safety in mind; however,it can present hazards if improperly operated and serviced. Followoperating instructions carefully! If you have questions about operatingor servicing this equipment, please contact Wacker Corporation.

The information contained in this manual was based on machines inproduction at the time of publication. Wacker Corporation reserves theright to change any portion of this information without notice.

All rights, especially copying and distribution rights are reserved.

Copyright 2002 by Wacker Corporation.

No part of this publication may be reproduced in any form or by anymeans, electronic or mechanical, including photocopying, withoutexpress written permission from Wacker Corporation.

Any type of reproduction or distribution not authorized by WackerCorporation represents an infringement of valid copyrights and will beprosecuted. We expressly reserve the right to make technicalmodifications, even without due notice, which aim at improving ourmachines or their safety standards.

WARNING

Safety Information VPA

2. Safety Information

This manual contains DANGER, WARNING, CAUTION, and NOTEcallouts which must be followed to reduce the possibility of personalinjury, damage to the equipment, or improper service.

This is the safety alert symbol. It is used to alert you to potentialpersonal injury hazards. Obey all safety messages that follow thissymbol to avoid possible injury or death.

DANGER indicates an imminently hazardous situation which, if notavoided, will result in death or serious injury.

WARNING indicates a potentially hazardous situation which, if notavoided, could result in death or serious injury.

CAUTION indicates a potentially hazardous situation which, if notavoided, may result in minor or moderate injury.

CAUTION: Used without the safety alert symbol, CAUTION indicatesa potentially hazardous situation which, if not avoided, may result inproperty damage.

Note: Contains additional information important to a procedure.

2.1 Laws Pertaining to Spark Arresters

Notice: State Health Safety Codes and Public Resources Codesspecify that in certain locations spark arresters be used on internalcombustion engines that use hydrocarbon fuels. A spark arrester is adevice designed to prevent accidental discharge of sparks or flamesfrom the engine exhaust. Spark arresters are qualified and rated bythe United States Forest Service for this purpose.

In order to comply with local laws regarding spark arresters, consultthe engine distributor or the local Health and Safety Administrator.

DANGER

WARNING

CAUTION

wc_si000028gb.fm 4

VPA Safety Information

2.2 Operating Safety

Familiarity and proper training are required for the safe operation ofequipment! Equipment operated improperly or by untrained personnelcan be dangerous! Read the operating instructions contained in boththis manual and the engine manual and familiarize yourself with thelocation and proper use of all controls. Inexperienced operators shouldreceive instruction from someone familiar with the equipment beforebeing allowed to operate the machine.

2.2.1 NEVER allow anyone to operate this equipment without propertraining. People operating this equipment must be familiar with therisks and hazards associated with it.

2.2.2 NEVER touch the engine or muffler while the engine is on orimmediately after it has been turned off. These areas get hot and maycause burns.

2.2.3 NEVER use accessories or attachments that are not recommended byWacker. Damage to equipment and injury to the user may result.

2.2.4 NEVER operate the machine with the belt guard missing. Exposeddrive belt and pulleys create potentially dangerous hazards that cancause serious injuries.

2.2.5 NEVER leave machine running unattended.

2.2.6 ALWAYS be sure operator is familiar with proper safety precautionsand operation techniques before using machine.

2.2.7 ALWAYS wear protective clothing appropriate to the job site whenoperating equipment.

2.2.8 ALWAYS wear hearing protection when operating equipment.

2.2.9 ALWAYS close fuel valve on engines equipped with one whenmachine is not being operated.

2.2.10 ALWAYS store equipment properly when it is not being used.Equipment should be stored in a clean, dry location out of the reach ofchildren.

2.2.11 ALWAYS operate machine with all safety devices and guards in placeand in working order. DO NOT modify or defeat safety devices. DONOT operate machine if any safety devices or guards are missing orinoperative.

2.2.12 ALWAYS read, understand, and follow procedures in Operator'sManual before attempting to operate equipment.

WARNING

wc_si000028gb.fm 5


2.3 Operator Safety while using Internal Combustion Engines

Internal combustion engines present special hazards during operationand fueling! Read and follow warning instructions in engine owner'smanual and safety guidelines below. Failure to follow warnings andsafety guidelines could result in severe injury or death.

2.3.1 DO NOT run machine indoors or in an enclosed area such as a deeptrench unless adequate ventilation, through such items as exhaustfans or hoses, is provided. Exhaust gas from the engine containspoisonous carbon monoxide gas; exposure to carbon monoxide cancause loss of consciousness and may lead to death.

2.3.2 DO NOT smoke while operating machine.

2.3.3 DO NOT smoke when refueling engine.

2.3.4 DO NOT refuel hot or running engine.

2.3.5 DO NOT refuel engine near open flame.

2.3.6 DO NOT spill fuel when refueling engine.

2.3.7 DO NOT run engine near open flames.

2.3.8 ALWAYS refill fuel tank in well-ventilated area.

2.3.9 ALWAYS replace fuel tank cap after refueling.

2.3.10 ALWAYS check fuel lines and fuel tank for leaks and cracks beforestarting engine. Do not run machine if fuel leaks are present or fuellines are loose.

DANGER

wc_si000028gb.fm 6


2.4 Service Safety

Poorly maintained equipment can become a safety hazard! In orderfor the equipment to operate safely and properly over a long period oftime, periodic maintenance and occasional repairs are necessary.

2.4.1 DO NOT attempt to clean or service machine while it is running.Rotating parts can cause severe injury.

2.4.2 DO NOT crank a flooded engine with the spark plug removed ongasoline-powered engines. Fuel trapped in the cylinder will squirt outthe spark plug opening.

2.4.3 DO NOT test for spark on gasoline-powered engines, if engine isflooded or the smell of gasoline is present. A stray spark could ignitefumes.

2.4.4 DO NOT use gasoline or other types of fuels or flammable solvents toclean parts, especially in enclosed areas. Fumes from fuels andsolvents can become explosive.

2.4.5 ALWAYS keep area around muffler free of debris such as leaves,paper, cartons, etc. A hot muffler could ignite them, starting a fire.

2.4.6 ALWAYS replace worn or damaged components with spare partsdesigned and recommended by Wacker.

2.4.7 ALWAYS disconnect spark plug on machines equipped with gasolineengines, before servicing, to avoid accidental start-up.

2.4.8 ALWAYS keep machine clean and labels legible. Replace all missingand hard-to-read labels. Labels provide important operatinginstructions and warn of dangers and hazards.

WARNING

wc_si000028gb.fm 7


2.5 Label Locations

1 2 3 4 5 6 7 1 2

WARNINGWARNUNG

ADVERTENCIAAVERTISSEMENT

10W30

wc_si000028gb.fm 8


2.6 Warning and Informational Labels

Wacker machines use international pictorial labels where needed.These labels are described below:

Label Meaning

To prevent hearing loss, wear hearing protec-tion when operating this machine.

Read the operator's manual for machine infor-mation.

Check engine oil level. Use SAE10W30.

Check fuel level.

WARNING! Hot surface.

Machine sound power level in dB(A).

� � � � �

wc_si000028gb.fm 9


WARNING! Hand injury if caught in moving belt. Always replace belt guard.

CAUTION!Read and understand the supplied operator's manual before operating this machine. Failure to do so increases the risk of injury to yourself or others.

CAUTION! Lifting point

DANGER!Engines emit carbon monoxide; operate only in well ventilated area. Read the operator's manual.No sparks, flames or burning objects near machine. Shut off engine before refueling.

A nameplate listing the Model Number, Item Number, Revision, and Serial Number is attached to each unit. Please record the infor-mation found on this plate so it will be avail-able should the nameplate become lost or damaged. When ordering parts or requesting service information, you will always be asked to specify the model, item number, revision number, and serial number of the unit.

Label Meaning

wc_si000028gb.fm 10


This machine may be covered by one or more patents.

Label Meaning

wc_si000028gb.fm 11


2.7 Operating Labels

Wacker machines use international pictorial labels where needed.These labels are described below:

Label Meaning

Open fuel flow valve.

Push or turn engine switch to ON position.

Close choke.

Place throttle in the IDLE position.

Pull rewind starter.

Close fuel flow valve.

wc_si000028gb.fm 12


Push or turn engine switch to OFF position.

Open choke.

Place throttle in the FAST position.

Throttle control lever:Rabbit = Full or FastTurtle = Idle or Slow

Label Meaning

1

wc_si000028gb.fm 13

Technical Data VPA

3. Technical Data

3.1 Engine Data

VPA174000067940008062

VPA17500006792

Engine

Engine Make Honda

Engine Model GX 160 K1 QX2

Rated Power kW (Hp) 4.1 (5.5)

Engine Speed - full rpm 3600 ± 100

Engine Speed - idle rpm 1600 ± 100

Clutch Engagement rpm 2100

Spark Plug type NGK BPR 6ES

Electrode Gap mm (in) 0.7–0.8 (0.028–0.031)

Air Cleaner type Dual Element

Engine Lubrication oil grade SAE 10W30

service class SG or SF

Engine Oil Capacity ml (oz.) 600 (20)

Fuel type Regular unleaded gasoline

Fuel Tank Capacity l (qts.) 3.7 (3.9)

Valve Clearance (cold) mm (in.) Inlet: 0.15 (0.006)Outlet: 0.20 (0.008)

wc_td000015gb.fm 14

VPA Technical Data

3.2 Machine Data

3.3 Sound and Vibration Specifications

The required sound specifications, per Appendix 1, Paragraph 1.7.4.fof the EC-Machine Regulations, are:

• the sound pressure level at operator’s location (LpA) = 97 dB(A)

• the sound power level (LWA) = 106 dB(A)

These sound values were determined according to ISO 3744 for thesound power level (LWA) and ISO 6081 for the sound pressure level(LpA) at the operator’s location.

The weighted effective acceleration value, determined according toISO 8662 Part 1, is 17 m/s2.

The sound and vibration specifications were obtained with the unitoperating on crushed gravel at nominal engine speed.

VPA174000067940008062

VPA17500006792

Plate

Operating Weight kg (lbs.) 91 (200) 98 (217)

Water Tank Capacity l (qts.) 12 (13)

Exciter Speed rpm / belt 5800 ± 100

Exciter Lubrication ml (oz.) 800 (27)SAE 30W

wc_td000015gb.fm 15

Technical Data VPA

3.4 Dimensions

mm (in.)

� � � � � � � � � � �

� � � � � �

� � � � � � �

� � � � � � � � � � � � � � � � � � � � �

� � � � � �

� � � � � � ��

wc_td000015gb.fm 16

VPA Operation

4. Operation

4.1 Recommended Fuel

The engine requires regular grade unleaded gasoline. Use only fresh,clean gasoline. Gasoline containing water or dirt will damage fuelsystem. Consult engine owner’s manual for complete fuelspecifications.

4.2 Before Starting

4.2.1 Read and understand safety and operating instructions at beginning ofthis manual.

4.2.2 Check:

• oil level in engine.

• fuel level.

• condition of air cleaner.

• tightness of external fasteners.

• condition of fuel lines.

4.3 To Start

See Graphic: wc_gr000014

4.3.1 Open fuel valve by moving lever to the right (a1).

Note: If engine is cold, move choke lever to close position (b1). Ifengine is hot, set choke to open position (b2 ).

4.3.2 Turn engine switch to “ON” (e1).

4.3.3 Open throttle by moving it slightly to left (d1).

4.3.4 Pull starter rope (c).

Note: If the oil level in the engine is low, the engine will not start. If thishappens, add oil to engine. Some engines are equipped with an oilalert light (f) that will come on while pulling the starter rope.

4.3.5 Open choke as engine warms (b2).

4.3.6 Open throttle fully to operate.

wc_tx000100gb.fm 17

Operation VPA

4.4 To Stop


4.4.1 Reduce engine RPM to idle by moving throttle completely to right (d2).

4.4.2 Turn engine switch to “OFF” (e2).

4.4.3 Close fuel valve by moving lever to the left (a2).

4.5 Application

This plate is designed for compacting loose, granular soils, gravel, andpaving stones. It is intended to be used in confined areas and areasnext to structures such as walls, curbs, and foundations. Platesequipped with water tanks can be used for compacting asphalt.

This plate is not recommended for compacting cohesive soils with aheavy clay content. For cohesive soil, use a vibratory rammer orsheepsfoot roller.

wc_tx000100gb.fm 18

VPA Operation

4.6 Operation

Run the engine at full throttle and allow the plate to pull itself along atits normal speed. When operating on an incline it may be necessary toassist the plate by pushing it forward slightly. When operating downhillhold the plate back slightly, if it begins to pick up speed. Depending onthe material being compacted, three or four passes are recommendedto achieve the best compaction.

While a certain amount of moisture in the soil is necessary, excessivemoisture may cause soil particles to stick together and prevent goodcompaction. If soil is extremely wet, allow it to dry somewhat beforecompacting.

If soil is so dry as to create dust clouds while operating plate, somemoisture should be added to the ground material to improvecompaction. This will also reduce service to the air filter.

For compacting asphalt, use a water tank to wet the asphalt and theunderside of plate. This will prevent asphalt material from sticking.Two passes are usually sufficent to ensure good compaction.

When using the plate on paving stones, attach a pad to the bottom ofthe plate to prevent chipping or grinding surface of stones. A specialpolyurethane pad designed for this purpose is available as an optionalaccessory.

CAUTION: DO NOT operate the plate on concrete or on extremelyhard, dry, compacted surfaces. The plate will jump rather than vibrateand could damage both the plate and the engine.

wc_tx000100gb.fm 19

Maintenance VPA

5. Maintenance

5.1 Periodic Maintenance Schedule

The chart below lists basic engine maintenance. Refer to enginemanufacturer’s Operation Manual for additional information on enginemaintenance.

5.2 Cleaning Plate

Clean plate after use to remove dirt, stones, and mud caught under theengine console. If plate is being used in a dusty area, check enginecylinder cooling fins for heavy dirt accumulation. Keep engine cylinderfins clean to prevent engine from overheating.

Dailybefore

starting

Afterfirst

20 hrs.

Every 2 weeks

or 50 hrs.

Every month

or 100 hrs.

Every yearor

300 hrs.

Check fuel level. •

Check engine oil level. •

Inspect fuel lines. •

Inspect air filter. Replace as needed. •

Check and tighten external hardware. •

Check and adjust drive belt. • •

Clean air cleaner elements. •

Inspect shockmounts for damage. •

Change engine oil. • •

Clean cooling system. •

Clean sediment cup / fuel filter. •

Check and clean spark plug. •

Check and adjust valve clearance. •

Change exciter oil. •

wc_tx000101gb.fm 20

VPA Maintenance

5.3 Engine Oil


5.3.1 Drain oil while the engine is still warm.

5.3.2 Remove the oil fill plug (a) and drain plug (b) to drain oil.

Note: In the interests of environmental protection, place a plastic sheetand a container under the machine to collect any liquid which drainsoff. Dispose of this liquid in accordance with environmental protectionlegislation.

5.3.3 Install drain plug.

5.3.4 Fill the engine crankcase with recommended oil up to the level of theplug opening (c). See Technical Data for oil quantity and type.

5.3.5 Install the oil filler plug.

wc_tx000101gb.fm 21

Maintenance VPA

5.4 Air Cleaner


The engine is equipped with a dual element air cleaner. Service aircleaner frequently to prevent carburetor malfunction.

CAUTION: NEVER run engine without air cleaner. Severe enginedamage will occur.

NEVER use gasoline or other types of low flash point solvents forcleaning the air cleaner. A fire or explosion could result.

To service:

5.4.1 Remove air cleaner cover (a). Remove both elements and inspectthem for holes or tears. Replace damaged elements.

5.4.2 Wash foam element (b) in solution of mild detergent and warm water.Rinse thoroughly in clean water. Allow element to dry thoroughly. Soakelement in clean engine oil and squeeze out excess oil.

5.4.3 Tap paper element (c) lightly to remove excess dirt. Replace paperelement if it appears heavily soiled.

WARNING

wc_tx000101gb.fm 22

VPA Maintenance

5.5 Spark Plug


Clean or replace spark plug as needed to ensure proper operation.Refer to the engine Owner’s Manual.

The muffler becomes very hot during operation and remains hot for awhile after stopping the engine. Do not touch the muffler while it is hot.

Note: Refer to the Technical Data for the recommended spark plugtype and the electrode gap setting.

5.5.1 Remove spark plug and inspect it.

5.5.2 Replace plug if the insulator is cracked or chipped.

5.5.3 Clean spark plug electrodes with a wire brush.

5.5.4 Set the electrode gap (a).

5.5.5 Tighten spark plug securely.

CAUTION: A loose spark plug can become very hot and may causeengine damage.

WARNING

wc_tx000101gb.fm 23

Maintenance VPA

5.6 Exciter Lubrication


The bearings in the exciter assembly are splash lubricated and rotateat very high speed. It is important to maintain the exciter oil at thecorrect level and change it regularly.

Check oil level in exciter each day, before running plate.

5.6.1 To check the oil level, place the plate on a flat, level surface.

5.6.2 Oil level should appear near center of sight glass (a).

5.6.3 Add oil as required.

Change exciter oil every 300 hours of operation.

5.6.1 To drain oil, remove plug (b) from end of exciter and tilt plate up.

Note: In the interests of environmental protection, place a plastic sheetand a container under the machine to collect any liquid which drainsoff. Dispose of this liquid in accordance with environmental protectionlegislation.

5.6.2 Place the plate on a level surface and add approximately 800 ml (27oz.) of oil through plug opening until oil appears near the center of thesight glass (a).

CAUTION: DO NOT overfill. Too much oil in exciter can reduceperformance and damage drive belt.

� � � � � � � � � �

�

�

wc_tx000101gb.fm 24

VPA Maintenance

5.7 Drive Belt


On new machines or after installing a new belt, check belt tension afterfirst 20 hours of operation. Check and adjust belt every 50 hoursthereafter.

To adjust belt:

5.7.1 Remove the two screws (b) at the bottom of the guard and the two nuts(a) located behind the guard.

5.7.2 Remove belt guard.

5.7.3 Loosen the four bolts (c) which hold the engine to the plate.

5.7.4 Slide engine back toward the handle to tighten belt, forward to loosenbelt.

5.7.5 Adjust belt so that it deflects 10-13 mm (3/8"-1/2") (d) when pressedmidway between belt pulleys.

� � � � � � � � � �

��

�

�

�

wc_tx000101gb.fm 25

Maintenance VPA

5.8 Adjusting Engine Speed


Adjust engine to the full load speed. See Technical Data.

To adjust idle speed:

5.8.1 Place machine on a rubber test mat to prevent it from moving.

5.8.2 Start the engine and allow it to warm up to normal operatingtemperature.

5.8.3 Turn the throttle stop screw (a) in to increase speed, out to decreasespeed. Make sure the throttle lever is touching the stop screw beforemeasuring rpm.

CAUTION: Running the plate at a speed higher than that listed inTechnical Data can damage both the plate and the engine.

5.9 Cleaning Sediment Cup


5.9.1 Turn fuel valve off.

5.9.2 Remove sediment cup (a) and O-ring (b).

5.9.3 Wash both thoroughly in a nonflammable solvent. Dry and reinstallthem.

5.9.4 Turn fuel valve on and check for leaks.

5.9.5

wc_gr000280

a

wc_tx000101gb.fm 26

VPA Maintenance

5.10 Carburetor Adjustment


5.10.1 Start the engine and allow it to warm up to operating temperature.

5.10.2 Set the pilot screw (a) 2 turns out. See Note.

5.10.3 With the engine idling, turn the pilot screw (a) in or out to the settingthat produces the highest rpm.

5.10.4 After the pilot screw is adjusted, turn the throttle stop screw (b) toobtain the standard idle speed. See Technical Data.

Note: On some engines the pilot screw is fitted with a limiter cap (c)to prevent excessive enrichment of the air-fuel mixture in order tocomply with emission regulations. The mixture is set at the factory andno adjustment should be necessary. Do not attempt to remove thelimiter cap. The limiter cap cannot be removed without breaking thepilot screw.

5.11 Storage

If plate is being stored for more than 30 days:

5.11.1 Remove loose stones and dirt from plate.

5.11.2 Clean engine cylinder cooling fins.

5.11.3 Clean or replace air filter.

5.11.4 Change engine oil and follow procedures described in engine manualfor engine storage.

5.11.5 Cover plate and engine and store in a clean, dry area.

wc_tx000101gb.fm 27

Maintenance VPA

5.12 Lifting Machine


See Technical Data for the weight of the machine.

To lift machine manually:

5.12.1 Stop the engine.

5.12.2 Obtain help from a partner and plan the lift.

5.12.3 Grasp the machine by its cage (a) and lifting handle (b).

5.12.4 Lift the machine as shown.

To reduce risk of back injury while lifting, keep your feet flat on groundand shoulder width apart. Keep your head up and back straight.

To lift machine mechanically:

CAUTION: Before attempting to lift, be sure that all lifting devices cansafely handle the weight of the machine. See Technical Data for theweight of the machine.

5.12.5 Attach hook, harness, or cable to the machine as shown and lift asdesired.

CAUTION: DO NOT lift the vibroplate by its guide handle. Thevibroplate can shift, causing it to fall.

WARNING

ab

wc_gr000352

wc_tx000101gb.fm 28

VPA Maintenance

5.13 Transporting Machine


To avoid burns or fire hazards, let engine cool before transportingmachine or storing indoors.

5.13.1 Turn fuel valve to the off position and keep the engine level to preventfuel from spilling.

5.13.2 Tie down machine on vehicle to prevent machine from sliding or tippingover. Tie machine to vehicle at points shown on graphic.

WARNING

wc_gr000354

wc_tx000101gb.fm 29

Maintenance VPA

5.14 Troubleshooting

Problem / Symptom Reason / Remedy

Plate does not develop full speed. Poor compaction.

• Engine throttle control not completely open.

• Throttle control not adjusted correctly.

• Ground too wet, plate sticking. Allow soil to dry before compacting.

• Drive belt loose or worn, slipping on pulleys. Adjust or replace belt. Check that engine mounting bolts are tight.

• Exciter bearings binding. Check condition and level of oil in exciter. Add or change oil.

• Air filter clogged with dust, reducing engine perfor-mance. Clean or replace air filter.

• Engine speed too low. Check engine speed with tachometer. Adjust or repair engine to run at correct speed. Refer to engine manual.

Engine running, no vibration • Engine throttle not open.

• Drive belt loose or broken. Adjust or replace.

• Clutch damaged. Inspect and replace clutch.

• Engine speed too low. Check engine speed.

• Too much oil in exciter. Adjust oil to correct level.

Plate jumps or compacts unevenly.

• Ground surface too hard.

• Shockmounts loose or damaged.

wc_tx000101gb.fm 30

EC - CONFORMITY CERTIFICATEEG-KONFORMITÄTSERKLÄRUNG

CE-CERTIFICADO DE CONFORMIDADCERTIFICAT DE CONFORMITÉ DE LA CEE

WACKER CORPORATION, N92 W15000 Anthony Avenue, MENOMONEE FALLS, WISCONSIN USA

hereby certifies that the construction equipment specified hereunder:bescheinigt, daß das Baugerät:certifica que la máquina de construcción:atteste que le matériel:

1. Category / Art / Categoría / Catégorie

2. Type - Typ - Tipo - Type

3. Item number of equipment / Gerätetypnummer /Número de referencia de la máquina / Numéro de référence du matériel :

4. Net installed power / absolute installierte Leistung /Potencia instalada neta / Puissance installée nette:

Has been sound tested per Directive 2000/14/EC / in Übereinstimmung mit Richtlinie 2000/14/EG bewertet worden ist /Ha sido ensayado en conformidad con la norma 2000/14/CE / a été mis à l’épreuve conforme aux dispositions de la directive2000/14/CEE :

and has been produced in accordance with the following standards:und in Übereinstimmung mit folgenden Richtlinien hergestellt worden ist:y ha sido fabricado en conformidad con las siguientes normas:et a été produit conforme aux dispositions des directives européennes ci-après :

2002-CE-WP1550.p65

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

VibroplateVibrationsplatte

Plancha VibradoraPatin Vibrant

VPA 1740, VPA 1750,VPA1740 w/cage

0006794, 0006792,0008062

4,1 kW

WACKER CORPORATION

William Lahner Greg Orzal

Conformity Assessment ProcedureKonformitätsbewertungsverfahrenProcedimiento para ensayarconformidad / Procédé pourl’épreuve de conformité

Name and address of notifiedbody /Bei folgender einbezogenerPrüfstelle / Oficina matriculadora/ Organisme agrée

Measured sound power level /Gemessener Schall-leistungspegel / Nivel de potenciaacústica determinado / Niveau depuissance acoustique fixé

Annex VIIIBSI, 389 Chiswick High RoadLondon W4 4AL United Kingdom 106 dB(A)

Guaranteed sound power level/Garantierter Schallleistungs-pegel / Nivel de potenciaacústica garantizado / Niveaude puissance acoustiquegaranti

2000/14/ECEMC 89/336/EECEN 50082-1VDE 0879-198/37/EECEN 500-1EN 500-4

106 dB(A)

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

Date / Datum / Fecha / Date

29.10.01

DEUTSCHLAND80809 MÜNCHEN PREUSSENSTR. 41 Tel. 089/35 40 21

Fax 089/35 40 23 9085757 Karlsfeld (WLZ) Tel. 018131-5978021109 Hamburg Fax 040/75 73 90 Tel. 040/75 15 6624145 Kiel Fax 0431/71 46 25 Tel. 0431/71 15 2523566 Lübeck Fax 0451/62 56 15 Tel. 0451/62 56 1928307 Bremen-Mahndorf Fax 0421/48 15 36 Tel. 0421/48 15 0126789 Leer-Bingum Fax 0491/6 25 39 Tel. 0491/6 72 2030165 Hannover Fax 0511/3 52 49 69 Tel. 0511/3 52 40 6138112 Braunschweig Fax 0531/31 29 24 Tel. 0531/31 21 8034233 Fuldatal Fax 0561/81 10 58 Tel. 0561/81 10 5940721 Hilden Fax 02103/4 69 31 Tel. 02103/3 10 4841065 Mönchengladbach Fax 02161/4 25 44 Tel. 02161/48 11 4146485 Wesel Fax 0281/5 16 37 Tel. 0281/8 98 7945326 Essen Fax 0201/32 13 02 Tel. 0201/31 17 9348291 Telgte Fax 02504/71 47 Tel. 02504/26 6849565 Bramsche Fax 05461/49 22 Tel. 05461/6 21 2144319 Dortmund Fax 0231/21 82 27 Tel. 0231/21 82 2633659 Bielefeld Fax 0521/40 31 14 Tel. 0521/4 07 7752355 Düren Fax 02421/6 21 22 Tel. 02421/6 30 5153842 Troisdorf Fax 02241/4 65 75 Tel. 02241/4 40 3156218 Mülheim-Kärlich Fax 0261/2 65 55 Tel. 0261/2 65 1057080 Siegen Fax 0271/31 10 49 Tel. 0271/31 50 5560388 Frankfurt Fax 069/41 71 89 Tel. 069/42 40 8035398 Gießen Fax 0641/2 98 19 Tel. 0641/2 22 6955129 Mainz-Hechtsheim Fax 06131/50 79 80 Tel. 06131/59 20 7066119 Saarbrücken Fax 0681/85 15 30 Tel. 0681/85 20 1167133 Maxdorf Fax 06237/50 08 Tel. 06237/72 0074172 Neckarsulm-Obereisesheim Fax 07132/4 36 19 Tel. 07132/4 36 1871254 Ditzingen Fax 07156/1 82 04 Tel. 07156/60 5472336 Balingen-Frommern Fax 07433/3 76 86 Tel. 07433/47 5376327 Pfinztal Fax 0721/46 86 60 Tel. 0721/46 04 6777746 Schutterwald Fax 0781/5 97 13 Tel. 0781/5 23 4378315 Radolfzell Fax 07732/5 65 08 Tel. 07732/5 64 8579112 Freiburg-Opfingen Fax 07664/5 97 76 Tel. 07664/10 1489155 Erbach Fax 07305/86 10 Tel. 07305/61 2288353 Kißlegg-Zaisenhofen Fax 07563/85 73 Tel. 07563/82 7685716 Unterschleißheim Fax 089/3 17 13 07 Tel. 089/3 10 60 3185077 Manching Fax 08459/76 02 Tel. 08459/69 9782538 Geretsried Fax 08171/3 14 09 Tel. 08171/3 12 6883064 Raubling Fax 08035/39 79 Tel. 08035/22 2294491 Hengersberg Fax 09901/32 13 Tel. 09901/21 9993128 Regenstauf Fax 09402/33 66 Tel. 09402/45 0190765 Fürth-Stadeln Fax 0911/76 34 90 Tel. 0911/76 40 2495326 Kulmbach Fax 09221/8 44 87 Tel. 09221/26 2097080 Würzburg Fax 0931/9 81 58 Tel. 0931/9 17 0863741 Aschaffenburg Fax 06021/8 36 17 Tel. 06021/8 36 1686167 Augsburg Fax 0821/70 78 58 Tel. 0821/70 22 07

13627 Berlin Fax 030/349 919-12 Tel. 030/349 919-013627 Berlin-Nord (Land-Brandenburg) Fax 030/344 13 52 Tel. 030/344 30 4714974 Genshagen (Berlin-Süd) Fax 03378/81 06 23 Tel. 03378/81 06 2119061 Schwerin/Görrîes Fax 0385/660 513 Tel. 0385/650 5501097 Dresden Fax 0351/803 60 91 Tel. 0351/803609004430 Blenltz/OT Dölzlg (Leipzig) Fax 034205/5 89 83 Tel. 034205/5898299428 Nohra (Erfurt) Fax 03643/82 58 28 Tel. 03643/82582609247 Röhrsdorf (Chemnitz) Fax 03722/50 24 85 Tel. 03722/502 48439167 Irxleben (Magdeburg) Fax 039204/6 64 78 Tel. 039204/56 7817033 Neubrandenburg Fax 0395/369 00 41 Tel. 0395/3690040

UNITED KINGDOMLONDON LEA ROAD Tel. (44)(01992) 707200

WALTHAM CROSS, HERTS EN9 1AW

Washington Washington/Tyne N37 1LH Tel. (0191) 4 16 63 92Warrington Winwick Quay, Warrington WA2 8RE Tel. (01925) 57 39 55Worksop Worksop S81 7BE Tel. (01909) 48 45 06Redditch Washford, Redditch B98 0DQ Tel. (01527) 2 45 56Pontypool Pontypool, Gwent NP4 6PD Tel. (01495) 75 05 95Ashford Ashford, Kent TN23 2NF Tel. (01233) 64 52 27Exeter Clyst, Honiton, Exeter EX5 2LG Tel. (01392) 6 97 71Hungerford Hungerford R617 OYX Tel. (01488) 68 14 28Lanarks Bellshill, Lanarks ML4 3NN Tel. (01698) 84 58 15

ÖSTERREICH1110 WIEN SCHEMMERLSTR.82 Tel. (43) 01-76715154050 Traun Wiener Bundesstr. 147 Tel. 07229-737399020 Klagenfurt Wiegelegasse 18 Tel. 0463-2627168054 Graz-Strassgang Kärntner Str. 512 Tel. 0316-2816906122 Fritzens Innstr. 11 Tel. 05224-513515300 Hallwang b. Sbg. Wiener Bundesstr. 17 Tel. 0662-6617413106 St. Pölten Hnilickastr. 9 Tel. 02742-73170

Wacker Corporation - P. O. Box 9007 - Menomonee Falls, WI 53052-9007 - Tel.: (262)-255-0500 - Fax: (262)-255-0550Wacker-Werke GmbH & Co. KG - Preußenstraße 41 - 80809 München - Tel.: +49-(0)89-354 02-0 - Fax: +49-(0)89-35 402-390

UNITED STATESCORPORATE OFFICEMENOMONEE FALLS, WI 53052 N92 W15000 ANTHONY AVE. Tel. (262) 255-0500

CANADAMISSISSAUGA, ONT. L5T 2N6 160 ADMIRAL BLVD. Tel. (905) 795-1661Calgary, Alta. T2H 2H9 #11, 6115-4 St. S.E. Tel. (403) 255-3336St. Laurent, Quebec H4R 2C1 3526 Rue Ashby Tel. (514) 337-1708

MEXICOMEXICO CITY 2A. CERRADA NORTE 147 NO. 20 Tel. (55) 53-53-15-03

COL. SAN MIGUEL AMANTLA 02700 Mexico D.F.Monterrey, Nuevo León Calle Nardo #970, Col. Cementos, C. P. 64520 Tel. (81) 83-31-12-85C. P. 45010, Zapopan, Jalisco Periférico Poniente No. 2100-Int. F, Tel. (33) 36271499

Col. Lomas del ColliC. P. 37530 León, Guanajuato Privada Manzanares #103, Fracc.San Isidro de Jerez Tel. (477)7-11-34-35C. P. 91700 Veracruz, Ver. Miguel Alemán No. 1001B, Col. Centro Tel. (229)9-35-10-44

ARGENTINA Colectora Oeste de Ruta Panamerica Tel. 5411-4-748-6800BUENOS AIRES 1611 Km 28.5 Don Torcuato

BRASIL Avda. Arquimedes 1070 Tel. 5511-4582-4333SÃO PAULO Unidade Autonoma No. 6

Jundiai, São Paulo

CHILESANTIAGO El Rosal 5000, Huechuraba, Casilla 130 - Correo 30 Tel. (56) 2-7400014Antofagasta Orella 975 Tel. (56) 55-227250Temuco Balmaceda 298 Tel. (56) 45-214425

AUSTRALIACLAYTON, VIC. 3169 PO Box 1315 RMDC Tel . (61) 03-95474033Norwood, S.A. 5067 45 Beulah Road Tel. 08-3622331Woodridge, QLD 4114 Unit 2, 6-8 Pendrey Court Tel. 07-32089577Osborne Park, W.A. 6017 Unit P, 69-73 Hector Street Tel. 09-4452911Auburn, N.S.W. 2144 14 Vore Street Tel. 02-7480366

JAPANOHTA-KU, TOYKO 144 2-CHOME 18-1, MINAMI-KAMATA Tel. (81) 03-37329281/5Hirano-ku, Osaka-shi Miyake Nishi, 4-Chome Tel. 0723 30-0571Sendai-shi Tachimachi 1-7-21 Tel. 022 284-8032Fukuoka-shi Sannoh 1-7-1, Hakata-ku Tel. 092 451-1083

MALAYSIA46150 PETALING JAYA 5. JALAN PJS 11/22 Tel. (03) 7364770Selangor Darul Ehsan Bandar Sunway

NEW ZEALAND 4A Ponui PlaceWIRI-AUCKLAND Mt. Wellington, Auckland Tel. (64) (9) 270 3784

SINGAPOREJURONG TOWN SINGAPORE 2263 NO. 23, Tuas Ave. 18 Tel. (65) 861-0446

THAILAND 22/197 Pattanakarn Rd. Tel. (66) 2-319-9363/65BANGKOK 10250 Soi Mooban Panya

SOUTH AFRICA 1031 KATROL AVE., ROBERTVILLE X10 Tel. H/O Jhb(011) 672-0847JOHANNESBURG Roodepoort / P.O. Box 2163, Florida 1710, Gauteng.Durban 10 Kinsman Rd. P.O. Box 420, New Germany 3620 Tel. Dbn(031) 702-3337Capetown Cor. Beatrix & Carel, Marincowitz St.

P.O. Box 398, Brackenfell 7560 Tel. Cpt(021) 981-2197

CHINA Unit 611-612, 6/F Sunley Centre Tel. (852) 24068613HONG KONG 9 Wing Yin Street

Kwai Chung, New Territories

0902

www.wackergroup.com

Documents

VPA 1740 VPA 1750 - Wacker Neusonproducts.wackerneuson.com/manuals/Operators/154574en_001.pdf · Arras 62217 Beaurains Tel. 3 21235361 Bordeaux 33700 Merignac Tel. 5 56343346 Bourges