V3 BTH-3 UG

8/3/2019 V3 BTH-3 UG

1/22

www.vthree.com.sg

vthreepteltd

User Guide

V3 Bluetooth Wireless Headset

2003-2004VThreePteLtd.AllRightsReserved.

FCCRegistration.ModelNumber:BTH3

8/3/2019 V3 BTH-3 UG

2/22

1. Introduction.................................................2

- Bluetooth wireless technology

2. Getting started.............................................3

3. Charging your Headset.................................4

- To Charge the headset

- Battery Indication

4. Pairing Headset to your Cell Phone...4 - 5

- To pair the devices

- To cancel pairing mode

5. Fitting Headset on your ear......................6

- To place the headset on your ear

- To add the fit ring

- To add the earhook

6. Powering Up..............................................7

- To turn ON/OFF the headset

7. Making Calls............................................7

- To make calls from your cell phone

- To make calls using voice dialing

8. Receiving Calls...........................................79. Ending Calls...............................................7

10. Transferring Calls.....................................8

- To transfer calls from your headset

- To transfer calls from your cell phone

11. Adjusting The Volume.................................8

- To increase/decrease volume

12. Muting/Un-muting Headset........................8

13. Last number dial......................................8

14. Troubleshooting.......................................9

15. Visual And Audible Indicators...........9 - 10

- Visual Indicators

- Audible Indicators

16. Technical Specifications.............................10

17. Customer Information............................11

18. Disclaimer...................................................11

ContentsEnglish

8/3/2019 V3 BTH-3 UG

3/22

IntroductionThank you for purchasing V3 Bluetooth BTH3.

Your V3 Bluetooth is a sleek cordless headset that

enables comfortable handsfree communication with

your Bluetooth cell phone.

V3 Bluetooth Wireless HeadsetUser Guide for BTH3

V3 Bluetooth Headset BTH32

Headset - Side A

Volumedown(-)

Volumeup(+)

Microphone

Multi-purpose

button(Power/OneTouch/

Pairing)

AmberLED

Blue

LED

EarhookHolder

Headset - Side B

Fit Ring

Speaker

Charging Point

8/3/2019 V3 BTH-3 UG

4/22


(A) Headset

(C) User Guide

(D) Fit Ring (E) Charging KitAC Adapter*

(B) Earhook

* NOTE:

The AC Adapter Plugis country dependent.

Getting Started

Remove all components from the package.

(A) Headset

(B) Earhook(C) User Guide

(D) Fit Ring

(E) Charger Kit - AC Adapter

8/3/2019 V3 BTH-3 UG

5/22


Charging your Headset

Before using headset, you must charge the headset

for approximately two hours. When fully charged,

the battery provides up to 8 hours oftalk time and up to 200 hours

of standby time.

Please note talk time is

also a function

of the mobilephone and

factory determined

settings of the phone

so you may find this

figure is reduced under certain conditions.

To charge the headset

1. Plug AC Adapter into Headset Charging Point

(as shown here).

2. Plug the other end of AC adapter into a wall

outlet. When the headset is charging, the amber

LED will light.

3. Unplug the charger cable from the wall outlet and

the headset after charge finish, the amber LED will

off.

Battery indication:

The amber LED will turn off after charging. This

indicated user can use this headset. However, it need

to take two hours to fully charge the battery.

Pairing Headset to your Cell Phone

Pairing is the process of linking the headset with

your Bluetooth cell phone. Before you use headset

with your cell phone you must pair the devices. After

this process is completed, you can use the headset

only with its paired cell phone. The pairing process

only need to be done once for continuous usage. If

you wish to use the headset with a different cell

phone, you must repeat the pairing process with the

new cell phone. In this case, the headset will no

longer work with the original cell phone. Before you

pair the headset, ensure that the battery is fullycharged.

Charging Kit(AC Adapdter)

HeadsetCharging Point

8/3/2019 V3 BTH-3 UG

6/22


To pair the devices

1. With the headset turned off, press and hold the

TALK button for five seconds. The blue and amber

LEDs will flash alternately, and you will hear the

PAIRING tone.

2. Release the TALK button. The headset is now in

Pairing Mode.

3. Turn on the cell phone and place it within 10

metres of the headset.

4. Initiate the device discovery feature on the cell

phone. Refer to the cell phone user guide for

instructions for initiating this feature.

5. When prompted by the cell phone, enter the

headset pin code 0000. When pairing is complete,the blue LED on the headset will flash at three

- second intervals and the headset will be placed

in standby mode, ready to make and receive calls.

If disconnection or lost links occur, it may be dueto the following reasons:

1. The range over 10 metres between both headset

and cell phone.

2.Cell phone to disconnect the link in order tosave the power or other purpose.

3.Either device has been switched off.

Note: The headset will keep the connection with cell

phone at all times if both connection links have been

built up.

To cancel pairing mode

While you are in pairing mode, you can cancel the

pairing process and turn off the headset.

Press and hold the TALK button for three seconds.

Both LEDs will turn off and you will hear the OFF

tone.

8/3/2019 V3 BTH-3 UG

7/22


Angled Headset towardyour mouth

Fitting Headset on

your ear

Headset is designed to fit

comfortably in your ear. Foradded comfort, you can add

the optional earhook and/or

fit ring.

To place the headset on your ear

Place the headset speaker in your ear with the micro-

phone angled toward your mouth as shown. The

headset should fit snugly in your ear. However, if the

speaker is too small for your ear, you can change to

other size of the fit ring that is provided with your

headset.

To add the fit ring

Stretch the fit ring around the end of the speaker

as shown.

Using Earhook

It is possible to remove

the ear hook and

replace but for normaloperation and fitment

this is NOT necessary.

Simply rotating the ear

hook on its axis will

allow easy fitment tothe ear.

Stretch fit ring around

the end of the speaker

Insert Earhook intoEarhook Holder

Earhook go around the earcomfortably

8/3/2019 V3 BTH-3 UG

8/22


Powering Up

To turn ON the headset

Press and hold the Talk button for four seconds. You

will hear the ON tone or blue light flash. The headsetturns on and is placed in standby mode, ready to

make and receive calls.

To turn OFF the headset

When the headset is on, press and hold the Talkbutton for four seconds. You will hear the OFF tone

or blue light off. The headset turns off.

Making Calls

You can make calls from your cell phone, or directly

from your headset using voice dialing commands

(if this feature is supported by your cell phone).

To make calls from your cell phone

Dial the call from your cell phone. The call is auto-matically connected to your headset.

To make calls using voice dialing

(if supported by your cell phone)

1. Press the Talk button on your headset.2. Speak the name of the person you wish to call.

The call is automatically connected to your

headset.

Receiving CallsYou must configure your cell phone to answer calls

directly on your headset. Refer to the cell phone user

guide for instructions for initiating this feature.

When your cell phone rings, press the Talk button

on your headset. The call is automatically connected

to your headset.

Ending CallsWhen you have finished your call, press the Talk

button on your headset. The call will be disconnected.

8/3/2019 V3 BTH-3 UG

9/22


Transferring Calls

You can transfer calls connected to your headset

back to your cell phone, or from your cell phone to

your headset.To transfer calls from your headset (phone

dependent)

To transfer calls from your cell phone

With the call connected to your cell phone, press

the Talkbutton on your headset.

Adjusting The Volume

To increase the volume

Press the top of the Volume button + to increase

volume by 1 level, repeat this procedure until you

have reached the desired level.

To decrease the volume

Press the bottom of the Volume button to decrease

the volume by one level, repeat this procedure untilyou have reached the desired level.

Muting / Un-muting Headset

You can mute and un-mute the microphone

temporarily so that you cannot be heard by theconnected party.

To mute the headset

Press and hold the Volume button for three seconds.

To un-mute the headsetWhen the microphone is muted, press and hold the

Volume button for three seconds.

Last Number Redial

Certain models only may have this feature. Depress

either volume button when headset is not on call for

about 3 second interval and this will enable the

phone to provide last number redial or alternately

press both volume up and down together.

8/3/2019 V3 BTH-3 UG

10/22

Trouble Shooting

Please note that you should also be familiar with

the operation of your mobile phone and how to

connect to Bluetooth devices. Please note that theBluetooth headset will only work with Bluetooth

mobile phones. For operation with a PC or laptop

device please note that these devices should also be

Bluetooth enabled with appropriate third party

software in order to enable correct operation.

Status

Battery 2/3 fullBattery low

Headset off

Headset in standbymode, ready to make and

receive calls

Headset is in pairing mode

Headset making connectionaudio connection for voicedial

Headset in talk mode

Indication

Amber LED is off or dimAmber LED on instead ofBlue LED

All LEDs are off

One Blue LED flashes at1 second intervals

One Blue and amber LEDsflash alternately

One Blue LED flashestwice quickly at1 second intervals

All LEDs flashes in circlequickly at 1 second intervals


Visual And Audible Indicators

Visual IndicatorsSIX LEDs (blue and amber)indicate the status of

the headset:

Symptom/Problem

When Talk button ispressed, no LED indicator

Headset powers onwith blue LED flashingbut no connection tomobile phone

Headset does not charge

Solution

Unit not charge Consult authzed dealer

Check unit is paired tophone. Check settings inphone. Headset defaultname is BTHS

Check phone is switched on Check handsfree settings

for phone Ensure headset & phone

are within range

Check mains chargeradapter is connected tothe headset securely & isswitched on

Check mains charger is

working using anotherdevice Consult authorized dealer

8/3/2019 V3 BTH-3 UG

11/22


Audible Indicators

Tones heard through the headset provide an audible

indication of a requested action:

Beep Tone IndicatesOn Headset has been on

Off Headset has been off

Pairing Headset has been putinto pairing mode

Model Number PBTHSTF2C2M-E

Bluetooth Compliance Bluetooth 1.2 Specification,

2.45GHz ISM band

Supported Bluetooth Bluetooth Hands-Free Profile 1.0

Profiles Bluetooth Headset Profile 1.0

Security Encrypted link

Operation Range Up to 10 metersConnection Point to Point

Paired Device Up to 7, one at a time

Talking Time Up to 8 Hours*

Standby Time Up to 200 Hours*

Operating Temperature -10 to 45C

Battery Rechargeable Li-Polymer Battery

Charging Time Up to 2 Hours 30 Minutes

Compatibility Bluetooth Enabled Phones

Weight 15 g

Size 58(L)x23(W)x30mm(H)

Technical Specifications

NOTE:

*Talk Time and Standby Time is dependent on phone models

and network providers.

8/3/2019 V3 BTH-3 UG

12/22


Customer Information

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference; and(2) this device must accept any interference received,

including interference that may cause undesired operation.

This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide

reasonable protection. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no

guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the

following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and

receiver.

Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician

for help.

Shielded interface cables must be used in order to comply

with emission limits. Changes or modifications not expressly

approved by the party responsible for compliance could

void the users authority to operate the equipment.

DisclaimerAny misuse and modification to the equipment that is not

stipulated in this user guide, shall render all warranty void.

The manufacturer shall not be held liable for any loss,

injuries or death resulting from the above stated scenario.

8/3/2019 V3 BTH-3 UG

13/22

1. ........................................................13

-

2. ........................................................14

3. ..............................................15

-

-

4. .......................15 - 16

-

-

5. ..........................................16 - 17

-

-

-

6. .................................................17

- /7. .................................................17

-

-

8. .................................................17

9. .....................................................18

10. .....................................................18

-

-

11. ...........................................18

- /

12. .....................................18

13. ..............................................................18

14. ..........................................18 - 19

15. .....................................19

-

-

16. .....................................................20

17. ....................................................20

18. ............................................................21

8/3/2019 V3 BTH-3 UG

14/22

V3BTH3

V3

V3 BTH2

V3 BTH313

(A) B

(A) A

(-)

(+)

(/,

)

LED

LED

8/3/2019 V3 BTH-3 UG

15/22

V3 BTH314

(C)

(D) (E)

(A)

(B)

(A)

(B)(C)

(D)

(E)

*:

AC

8/3/2019 V3 BTH-3 UG

16/22

V3 BTH315

1. AC

()2.AC

LED

3.

LED

LED

1.

LED2.

3.

AC

8/3/2019 V3 BTH-3 UG

17/22

V3 BTH316

4.

5. 0000

LED

10

LED

8/3/2019 V3 BTH-3 UG

18/22

V3 BTH317

(

)

()1.

2.

8/3/2019 V3 BTH-3 UG

19/22

V3 BTH318

()

+

-

3

8/3/2019 V3 BTH-3 UG

20/22

V3 BTH319

LED

LED , ,

BTHS

LED:

2/3 LED

LED

LED

3LED

LED

LED

LED

8/3/2019 V3 BTH-3 UG

21/22

V3 BTH320

FCC

:

1) (2)

B

FCC

:

-

-

-

-

PBTHSTF2C2M-E

1.2

2.45GB Hz ISM

1.0

1.0

10

-10 45

58 x 23 x 30()

8/3/2019 V3 BTH-3 UG

22/22

V3 BTH321

Documents

V3 BTH-3 UG