Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
TRANSMISSIONPRODUCTS
PUPI is a product of:
800.533.1680 | www.pupicrossarms.com
INNOVATIVE TECHNOLOGY – Only PUPI has thermally-bonded SunGUARD® UV protection for long life and TorqueGUARD™ bushings
for added hole strength. PUPI transmission braces are
available with patent-pending EZE-Fit™ end fittings that
adjust for attachment to pre-existing structures. GEOTEK,
the producer of PUPI crossarms, has nearly 40 years of
pultrusion experience and state-of-the-art composite
testing capabilities to drive constant innovation.
ECONOMICAL – The initial cost of PUPI transmission crossarms and braces is competitive with other materials, but PUPI delivers so
much more! PUPI’s light weight assemblies often require
less labor and lighter equipment to install. After installation,
PUPI’s long life and maintenance-free performance drives
down operating costs for years and years.
LONG-LASTING PERFORMANCE – The strength and performance characteristics of PUPI crossarms and braces do not change over time. PUPI
products do not rot, dry out, split, or shrink from the
effects of weather and UV radiation. They are completely
resistant to insects and woodpeckers. PUPI products
will never rust or require painting – they are truly
maintenance-free.
SUPERIOR INSULATING PROPERTIES – Unlike steel transmission structures, PUPI crossarms and braces have excellent insulating properties. In fact,
PUPI crossarms are often used with steel or concrete
poles to prevent unintended grounding. The smooth,
non-porous surface of PUPI crossarms resists surface
contamination and will never absorb water, making
PUPI a better insulator than wood. PUPI crossarms
have passed extensive electrical performance testing by
leading independent laboratories.
The Most Comprehensive Line Of Fiberglass Transmission Crossarms And Braces Available!
PUPI® is the leader in fiberglass crossarms for the electrical power industry. Available for single-pole and H-frame structures, PUPI transmission crossarms and braces are engineered for maximum strength and consistent performance in a wide-range of standard and made-to-order configurations. With exclusive SunGUARD® UV resistant coating and TorqueGUARD™ bushings, PUPI crossarms are proven to withstand the elements better than wood, steel or other composite beams – in any climate!
TRANSMISSION PRODUCTS
800.533.1680 | www.pupicrossarms.com
CUSTOM APPLICATION ENGINEERING – PUPI offers electric utilities the most complete line of fiberglass transmission crossarms and braces available.
PUPI crossarms and braces can be used in combination
with any type of pole material and can be fitted to a wide
variety of hardware and fittings. Gray and brown colors
are available. Our standard offerings are extensive and
our engineers are ready to design a PUPI solution to fit
nearly any transmission crossarm application.
STRONGER AND LIGHTER THAN WOOD – PUPI transmission crossarms and braces are constructed of pultruded fiberglass to deliver more consistent strength
with less weight than comparable wood assemblies.
Because PUPI products are manufactured under carefully
controlled conditions, they are free from the natural
variations found in wood. The strength performance of
PUPI products is consistent and reliable!
1 REV09.2015
SINGLE POLE STRUCTURE TRANSMISSION CROSSARMS
TRANSMISSION PRODUCTS
PUPI crossarms for single pole transmission structures can be designed to virtually any length or drill pattern – in either Tangent or Deadend configurations. Crossarms may be used with or without braces. A wide variety of fiberglass braces are available when required.
15’ load ratings are listed here, but virtually any combination of length and hole pattern is available. Final load ratings and other performance characteristics will depend on specific system configurations. Our engineering team is ready to review your system needs.
SINGLE POLE MOUNT TANGENT CROSSARMS (SELECTED)
PUPI PART NUMBER DESCRIPTIONCROSSARM PROFILE
DIMENSIONSULTIMATE VERTICAL LOAD
RATING PER SIDE
CROSSARM ASSEMBLY
WEIGHT (lbs)
TB3000180SPX2 15’ Single Arm With Pole Mount 3-5/8” X 4-5/8” 6,200 86
TB4000180SPX2 15’ Single Arm With Pole Mount 4” X 6” 8,800 111
Custom lengths are available. Load ratings and weights will vary with arm length and hardware configuration. Recommended maximum working load is 50% of ultimate strength.
SINGLE POLE MOUNT DEADEND ASSEMBLIES (SELECTED)
PUPI PART NUMBER DESCRIPTIONCROSSARM PROFILE
DIMENSIONSULTIMATE LOAD RATING
PER POSITION
CROSSARM ASSEMBLY
WEIGHT (lbs)
DA4000180E4SPX2 15’ Single Arm With Pole Mount. 4 Position. 4” X 6” 9,000 133
DA3020180E4SPX2 15’ Double Arm With Pole Mount. 4 Position. 3-5/8” X 4-5/8” 12,000 218
Custom lengths are available. Load ratings and weights will vary with arm length and hardware configuration. Recommended maximum working load is 50% of ultimate strength.
800.533.1680 | www.pupicrossarms.comFOR THE ENTIRE PUPI PRODUCT CATALOG VISIT:
T B 30 0 0 180 E 4 XXX 2MOUNT INSTALLATION:A = With Deadend center mountB = With Tangent center mount
ORIENTATION:T = TangentD = Deadend
COLOR:2 = Gray3 = Brown
LENGTH:in inches
BEAM SERIES:30 = 300040 = 4000
TORQUEGUARDBUSHINGS:0 = included in all holes2 = not included
CUSTOM SPECIFICATION CODENUMBER OF BEAMS IN ASSEMBLY:0 = 12 = 2
WIRE POSITIONS(DEADEND USE ONLY):
2 = 2 Wire Positions3 = 3 Wire Positions4 = 4 Wire Positions
EYE NUTS(DEADEND USE ONLY):
E = Eye nuts front and back sidesS = Eye nuts one side onlyX = No eye nuts supplied
2REV09.2015
800.533.1680 | www.pupicrossarms.com
PUPI H-frame tangent crossarms are available in a variety of standard dimensions and lengths, with or without galvanized steel pole mount hardware. Representative sizes and load ratings are listed here. Custom lengths and hole patterns are available. Final load ratings and other performance characteristics will depend on specific system configurations. Contact our engineering team to review your system needs.
H-FRAME TANGENT CROSSARM ASSEMBLIES
TRANSMISSION PRODUCTS
22’ H-FRAME TANGENT CROSSARM ASSEMBLIES - 3 POSITION
PUPI PART NUMBER DESCRIPTIONCROSSARM PROFILE
DIMENSIONSULTIMATE VERTICAL LOAD
RATING PER POSITION
CROSSARM ASSEMBLY
WEIGHT (lbs)
TX300026441H2 Single Arm 3 5/8” X 4 5/8” 6,000 95
TD300026441H2 Single Arm With Pole Mounts 3 5/8” X 4 5/8” 6,000 141
TX400026441H2 Single Arm 4” X 6” 9,000 129
TD400026441H2 Single Arm With Pole Mounts 4” X 6” 9,000 181
Ultimate vertical strength with 10.5’ pole spacing. Unless otherwise noted, strength ratings are for crossarms without braces. Recommended maximum working load is 50% of ultimate strength.
26’ H-FRAME TANGENT CROSSARM ASSEMBLIES - 3 POSITION
PUPI PART NUMBER DESCRIPTIONCROSSARM PROFILE
DIMENSIONSULTIMATE VERTICAL LOAD
RATING PER POSITION
CROSSARM ASSEMBLY
WEIGHT (lbs)
TX400031255H2 Single Arm 4” X 6” 7,500/15,000* 152
TD400031255H2 Single Arm With Pole Mounts 4” X 6” 8,000 204
TX402031254H2 Double Arm 4” X 6” 15,000 411
Ultimate vertical strength with 12.5’ pole spacing. Unless otherwise noted, strength ratings are for crossarms without braces. Recommended maximum working load is 50% of ultimate strength. *Rating with PUPI knee braces.
32’ H-FRAME TANGENT CROSSARM ASSEMBLIES - 3 POSITION
PUPI PART NUMBER DESCRIPTIONCROSSARM PROFILE
DIMENSIONSULTIMATE VERTICAL LOAD
RATING PER POSITION
CROSSARM ASSEMBLY
WEIGHT (lbs)
TX400038471H2 Single Arm 4” X 6” 4,000/15,000* 187
TX402038471H2 Double Arm 4” X 6” 8,000 481
TX302038471H2 Double Arm 3 5/8” X 4 5/8” 15,000* 376Ultimate vertical strength with 15.5’ pole spacing. Unless otherwise noted, strength ratings are for crossarms without braces. Recommended maximum working load is 50% of ultimate strength. *Rating with PUPI knee braces.
FOR THE ENTIRE PUPI PRODUCT CATALOG VISIT: 3 REV09.2015
T D 30 0 0 264 XXX 2
X = No mounts installedE = 3 mounts installed
ORIENTATION:T = Tangent
COLOR:2 = Gray3 = Brown
LENGTH:in inches.
BEAM SERIES:30 = 300040 = 4000
TORQUEGUARDBUSHINGS:0 = included in all holes2 = not included
CUSTOM SPECIFICATION CODENUMBER OF BEAMS IN ASSEMBLY:0 = 12 = 2
MOUNT INSTALLATION:D = 2 mounts installedC = 1 mount installed
H-FRAME DEADEND ASSEMBLIES
PUPI H-frame Deadend assemblies are available in standard lengths, as well as custom lengths upon request. Deadends are supplied with specially-designed galvanized pole mounting hardware. Representative sizes and load ratings are listed here. Custom lengths and hole patterns are available. Final load ratings and other performance characteristics will depend on specific system configurations. Contact our engineering team to review your system needs.
TRANSMISSION PRODUCTS
22’ H-FRAME DEADEND CROSSARM ASSEMBLIES – 3 POSITION
PUPI PART NUMBER DESCRIPTIONCROSSARM PROFILE
DIMENSIONSULTIMATE LOAD RATING
PER POSITION
CROSSARM ASSEMBLY
WEIGHT (lbs)
DD3000264E342H2 Single Arm With 2 Pole Mounts And Eye Hardware 3 5/8” X 4 5/8” 10,000 146
DD4000264E342H2 Single Arm With 2 Pole Mounts And Eye Hardware 4” X 6” 12,000 188
Ultimate vertical strength calculated with 14.5’ pole spacing. Recommended maximum working load is 50% of ultimate strength.
26’ H-FRAME DEADEND CROSSARM ASSEMBLIES – 3 POSITION
PUPI PART NUMBER DESCRIPTIONCROSSARM PROFILE
DIMENSIONSULTIMATE LOAD RATING
PER POSITION
CROSSARM ASSEMBLY
WEIGHT (lbs)
DD3000312E356H2 Single Arm With 2 Pole Mounts And Eye Hardware 3 5/8” X 4 5/8” 5,300 163
DD4000312E356H2 Single Arm With 2 Pole Mounts And Eye Hardware 4” X 6” 8,400 211
Ultimate vertical strength calculated with 12.5’ pole spacing. Recommended maximum working load is 50% of ultimate strength.
800.533.1680 | www.pupicrossarms.com
MOUNT INSTALLATION:D = 2 mounts installedC = 1 mount installed X = No mounts installedE = 3 mounts installed
D D 30 0 0 264 E 3 XXX 2
DEADEND EYE NUTS:E = Eye nuts front and back sidesS = Eye nuts one side only X = No eye nuts supplied COLOR:
2 = Gray3 = Brown
LENGTH:in inches.
WIREPOSITIONS DRILLED3 = 3 Wire Positions4 = 4 Wire Positions
TORQUEGUARDBUSHINGS:0 = included in all holes2 = not included
CUSTOM SPECIFICATION CODE
NUMBER OF BEAMS IN ASSEMBLY:0 = 12 = 2
ORIENTATION:D = Deadend
BEAMSERIES:30 = 300040 = 4000
FOR THE ENTIRE PUPI PRODUCT CATALOG VISIT: 4REV09.2015
XBR 3000 126 XXX 2
ORIENTATION:XBR = X-brace
COLOR:2 = Gray3 = Brown
POLE SPACING:in inches
BEAM SERIES:3020 = 3000 pair4020 = 4000 pair
CUSTOM SPECIFICATION CODE
H-FRAME KNEE & VEE BRACES
TRANSMISSION PRODUCTS
COLOR:2 = Gray3 = Brown
MOUNTING POSITION:TM = Beam Top MountDM = Spacer Mount
K 0092 TM XXX 6 2
HOLE CENTER- TO- HOLE CENTER LENGTH (inches)
ORIENTATION:K = Knee BraceV = Vee Brace
CUSTOM SPECIFICATION CODE
PROFILE:6 = Series 3000
KNEE & VEE BRACES
PUPI PART NUMBER DESCRIPTIONHOLE CENTER TO
HOLE CENTER LENGTHS
BEAM PROFILE DIMENSIONS
LENGTH ADJUSTMENT
TENSION STRENGTH
(lbs)
BRACE ASSEMBLY
WEIGHT in lbs)
K0092TMSPX62 Knee Brace 30° - 60° Variable Angle For 26’ Single Arm 92” 3 5/8” X 4 5/8” +/- 5” 20,000 66
K0092TM03662 Knee Brace 45° Fixed Angle For 26’ Single Arm 92” 3 5/8” X 4 5/8” fixed 20,000 52
V0098DMSPX62 Vee Brace 30° - 60° Variable Angle For 26’ Double Arm 98” 3 5/8” X 4 5/8” +/- 5” 20,000 65
K0118TMSPX62 Knee Brace 30° - 60° Variable Angle For 32’ Single Arm 118” 3 5/8” X 4 5/8” +/- 5” 20,000 75
K0118TM03562 Knee Brace 45° Fixed Angle For 32’ Single Arm 118” 3 5/8” X 4 5/8” fixed 20,000 61
V0123DMSPX62 Vee Brace 30° - 60° Variable Angle For 32’ Double Arm 123” 3 5/8” X 4 5/8” +/- 5” 20,000 75
800.533.1680 | www.pupicrossarms.com
X-BRACES
PUPI PART NUMBER DESCRIPTIONPOLE
SPACINGBEAM PROFILE DIMENSIONS
LENGTH ADJUSTMENT
TENSION STRENGTH
(lbs)
BRACE ASSEMBLY
WEIGHT in lbs)
XBR3020126SPX2 Pair of X-Braces, Including Center Clamp, Variable Angle 10.5’ 3 5/8” X 4 5/8” +/- 5” 25,000 210
XBR3020150SPX2 Pair of X-Braces, Including Center Clamp, Variable Angle 12.5’ 3 5/8” X 4 5/8” +/- 5” 25,000 235
XBR3020186SPX2 Pair of X-Braces, Including Center Clamp, Variable Angle 15.5’ 3 5/8” X 4 5/8” +/- 5” 25,000 271
XBR30201260272 Pair of X-Braces, Including Center Clamp, Fixed 45° Angle 10.5’ 3 5/8” X 4 5/8” fixed 25,000 159
XBR30201500342 Pair of X-Braces, Including Center Clamp, Fixed 45° Angle 12.5’ 3 5/8” X 4 5/8” fixed 25,000 186
XBR30201860292 Pair of X-Braces, Including Center Clamp, Fixed 45° Angle 15.5’ 3 5/8” X 4 5/8” fixed 25,000 223
XBR4020186SPX2 Pair of X-Braces, Including Center Clamp, Variable Angle 15.5’ 4” X 6” +/- 5” 30,000 348
PUPI fiberglass knee & vee braces are designed to work in a variety of applications. Fixed angle end fittings or adjustableend fittings are available in standard or custom lengths.
H-FRAME X-BRACESPUPI fiberglass X-braces are available in lengths to fit virtually any pole spacing. X-braces are available in pairs with either fixed angle or adjustable end fittings.
FOR THE ENTIRE PUPI PRODUCT CATALOG VISIT:
Our patent-pending EZE-Fit™ end fitting design provides 130° of angle adjustment – plus up to 10 inches of length adjustment per brace! EZE-Fit™ end fittings are designed to allow secure attachment to existing poles and attachment holes. This adjustability is especially valuable for use with concrete, composite or steel poles where field-drilling is difficult.
5 REV09.2015
Recommended maximum working load is 50% of ultimate strength.
Recommended maximum working load is 50% of ultimate strength.
130°
EZE-Fit™ Adjustable End Fitting:
TRANSMISSION PRODUCTS
800.533.1680 | www.pupicrossarms.com
TRANSMISSION HARDWARE AND FITTING SPECIFICATIONS
PUPI PART NUMBER PUPI TRANSMISSION POLE MOUNTFITS BEAM PROFILE
DIMENSIONSPOLE MOUNT HOLE
DIAMETERPOLE MOUNT
HOLE SPACINGSPOLE MOUNT
PLATE THICKNESSWEIGHT (lbs)
TMB-012 S3000 Tangent Pole Mount 3 5/8” X 4 5/8” 13/16” 8” 10” 12” 5/16” 23
TMB-013 S4000 Tangent Pole Mount 4” X 6” 13/16” 10” 12” 5/16” 26
DMB-008 S3000 Deadend Pole Mount 3 5/8” X 4 5/8” 13/16” 12” 5/16” 18
DMB-011 S4000 Deadend Pole Mount 4” X 6” 13/16” 12” 5/16” 21
PUPI PART NUMBER DOUBLE ARM TANGENT SPACERS FITS BEAM PROFILE DIMENSIONSATTACHMENT HOLE
DIAMETERRANGE OF SPACING
ADJUSTMENTWEIGHT (lbs)
BMB-018 Adjustable Double Arm Tangent Spacer 3 5/8” X 4 5/8” 15/16” 8.5” - 12.5” 34
BMB-019 Adjustable Double Arm Tangent Spacer 4” X 6” 15/16” 8.5” - 12.5” 36
PUPI PART NUMBER PUPI H-FRAME BRACE END FITTINGSFITS BEAM PROFILE
DIMENSIONSPOLE / BEAM MOUNT
HOLE DIAMETERANGLE
LENGTH ADJUSTABILITY
RANGE
POLE MOUNT PLATE
THICKNESSWEIGHT (lbs)
BMB-014Fixed Angle Knee & Vee Brace End
Fitting 3 5/8” X 4 5/8” 13/16” 45° Fixed none 5/16” 10
BMB-016EZE-Fit™ Adjustable Knee & Vee
Brace End Fitting 3 5/8” X 4 5/8” 13/16” Variable +/- 2.5” 5/16” 19
BMB-015 Fixed Angle X-brace End Fitting 3 5/8” X 4 5/8” 13/16” 45° Fixed none 5/16” 10
BMB-017EZE-Fit™ Adjustable X-brace End
Fitting 3 5/8” X 4 5/8” 13/16” Variable +/- 2.5” 5/16” 25
Each PUPI EZE-Fit™ end fitting can be adjusted +/-2.5” simply by changing the position of the adjustment bolts - that’s 10 inches of length adjustability per brace! Fittings have 130° of angle adjustability and saw-tooth mounting holes for precise fitting to installed poles with pre-drilled holes. Fixed-length 45°angle end fittings are also available.
FOR THE ENTIRE PUPI PRODUCT CATALOG VISIT:
Fixed 45° Angle End Fitting:
130°
+/- 2.5” +/- 2.5”
6REV09.2015
7
CONTACT:1421 Second Ave. NWStewartville, MN 55976 USA800.533.1680 or 507.533.6076 Fax: 507.533.4784
PUPI is a product of:
www.pupicrossarms.comFOR THE ENTIRE PRODUCT CATALOG VISIT:
TRANSMISSION PRODUCTS
EXTENSIVE PRODUCT TESTINGAll PUPI® products are the result of intensive design efforts and rigorous testing to assure they meet required performance standards and published specifications.
MECHANICAL TESTING – PUPI transmission crossarms are tested by applying vertical loads at a constant rate to the wire attachments, measuring load and deflection until the beam fractures. H-Frame assemblies are tested in 3 phase, 2 pole configurations. Load deflection plots are virtually linear to the fracture point for all PUPI crossarms.
PUPI mechanical test methods are designed to closely represent actual product service conditions. Test specimens are drilled with the same hole configuration as the final product. Production mounts and attachment hardware are used and loads are applied at the same points that will be used in the final application. To assure accuracy, our testing methods and procedures are verified by independent test facilities.
ELECTRICAL TESTING – PUPI transmission crossarms have undergone extensive electrical testing at leading independent laboratories.
PUPI high voltage fiberglass transmission structure testing (IEC 60060-1) 15+ impulses, 15- impulses• Dry lighting impulse tests to 1050 kV• Dry switching impulse tests to 850 kV• Dry power frequency tests to 460 kV• Wet switching impulse tests to 850 kV• Wet power frequency tests to 460 kV• No flashover in any tests, pass all test
ASTM Tests (coupons cut from beam walls)• Dielectric Strength (ASTM D149)
- 200 – 320 V/mil through beam wall, mean 254 V/mil- 141 – 196 V/mil along beam principal axis, mean 167 V/mil
• Surface Resistivity (ASTM D257)- 1 – 4 X 1015 ohms
IN-PROCESS QUALITY TESTING – In addition to performance testing, our manufacturing processes are constantly monitored with in-process quality control testing procedures. All GEOTEK products, including PUPI, are manufactured in accordance with our Quality Management System based on the ISO 9001:2008 framework.
Nobody has more experience testing fiberglass crossarms than PUPI.
H-FRAME TESTING
BUILT IN USAPUPI crossarms and braces are designed and built in the USA. All of our fiberglass pultrusion, fabrication and assembly are performed at our plant in Stewartville, MN.
PL006
REV09.2015