TLC227x, TLC227xA Advanced LinCMOS RAIL-TO-RAIL ...nic.vajn.icu/PDF/TexasInstruments/TLC2272.pdf · The TLC2272/4 also makes great upgrades to the TLC272/4 or TS272/4 in standard

TLC227x, TLC227xAAdvanced LinCMOS RAIL-TO-RAIL

OPERATIONAL AMPLIFIERSSLOS190B – FEBRUARY 1997 – REVISED JULY 1999

1POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

Output Swing Includes Both Supply Rails

Low Noise . . . 9 nV/√Hz Typ at f = 1 kHz

Low Input Bias Current . . . 1 pA Typ

Fully Specified for Both Single-Supply andSplit-Supply Operation

Common-Mode Input Voltage RangeIncludes Negative Rail

High-Gain Bandwidth . . . 2.2 MHz Typ

High Slew Rate . . . 3.6 V/µs Typ

Low Input Offset Voltage 950 µV Max at TA = 25°C

Macromodel Included

Performance Upgrades for the TS272,TS274, TLC272, and TLC274

Available in Q-Temp Automotive HighRel Automotive ApplicationsConfiguration Control / Print SupportQualification to Automotive Standards

description

The TLC2272 and TLC2274 are dual andquadruple operational amplifiers from TexasInstruments. Both devices exhibit rail-to-railoutput performance for increased dynamic rangein single- or split-supply applications. TheTLC227x family offers 2 MHz of bandwidth and3 V/µs of slew rate for higher speed applications.These devices offer comparable ac performancewhile having better noise, input offset voltage, andpower dissipation than existing CMOSoperational amplifiers. The TLC227x has a noisevoltage of 9 nV/√Hz, two times lower thancompetitive solutions.

The TLC227x, exhibiting high input impedanceand low noise, is excellent for small-signalconditioning for high-impedance sources, such aspiezoelectric transducers. Because of the micro-power dissipation levels, these devices work wellin hand-held monitoring and remote-sensingapplications. In addition, the rail-to-rail outputfeature, with single- or split-supplies, makes thisfamily a great choice when interfacing withanalog-to-digital converters (ADCs). For precision applications, the TLC227xA family is available and has amaximum input offset voltage of 950 µV. This family is fully characterized at 5 V and ±5 V.

The TLC2272/4 also makes great upgrades to the TLC272/4 or TS272/4 in standard designs. They offerincreased output dynamic range, lower noise voltage, and lower input offset voltage. This enhanced feature setallows them to be used in a wider range of applications. For applications that require higher output drive andwider input voltage range, see the TLV2432 and TLV2442 devices.

If the design requires single amplifiers, please see the TLV2211/21/31 family. These devices are singlerail-to-rail operational amplifiers in the SOT-23 package. Their small size and low power consumption, makethem ideal for high density, battery-powered equipment.

Copyright 1999, Texas Instruments IncorporatedPRODUCTION DATA information is current as of publication date.Products conform to specifications per the terms of Texas Instrumentsstandard warranty. Production processing does not necessarily includetesting of all parameters.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications ofTexas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

Advanced LinCMOS is a trademark of Texas Instruments Incorporated.

|VDD±| – Supply Voltage – V

10

8

6

44 6 8

12

14

16

10 12 14 16

MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGEvs

SUPPLY VOLTAGE

TA = 25°C

IO = ±50 µA

IO = ±500 µA

V(O

PP

) –

Max

imum

Pea

k-to

-Pea

k O

utpu

t Vol

tage

– V

VO

(PP

)

On products compliant to MIL-PRF-38535, all parameters are testedunless otherwise noted. On all other products, productionprocessing does not necessarily include testing of all parameters.

TLC227x, TLC227xAAdvanced LinCMOS RAIL-TO-RAILOPERATIONAL AMPLIFIERSSLOS190B – FEBRUARY 1997 – REVISED JULY 1999

2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

TLC2272 AVAILABLE OPTIONS

PACKAGED DEVICES

TAVIOmax At

25°CSMALL

OUTLINE†

(D)

PLASTIC DIP(P)

TSSOP‡

(PW)

0°C to 70°C 950 µV TLC2272ACD TLC2272ACPTLC2272CPW0°C to 70°C µ

2.5 mV TLC2272CD TLC2272CPTLC2272CPW

40°C to 85°C 950 µV TLC2272AID TLC2272AIP–40°C to 85°C µ

2.5 mV TLC2272ID TLC2272IP—

40°C to 125°C 950 µV TLC2272AQD TLC2272AQPW–40°C to 125°C µ

2.5 mV TLC2272QD—

TLC2272QPW

55°C to 125°C950 µV TLC2272AMD TLC2272AMP

–55°C to 125°Cµ

2.5 mV TLC2272MD TLC2272MP —

† The D packages are available taped and reeled. Add R suffix to the device type (e.g., TLC2272CDR).‡ The PW package is available taped and reeled. Add R suffix to the device type (e.g., TLC2272PWR).§ Chips are tested at 25°C.

TLC2274 AVAILABLE OPTIONS

PACKAGED DEVICES

TAVIOmax AT

25°CSMALL

OUTLINE†

(D)

CHIP CARRIER

(FK)

CERAMIC DIP(J)

PLASTICDIP(N)

TSSOP‡

(PW)

0°C to 950 µV TLC2274ACD TLC2274ACN —70°C

µ2.5 mV TLC2274CD

— —TLC2274CN TLC2274CPW

–40°C to 950 µV TLC2274AID TLC2274AIN —85°C

µ2.5 mV TLC2274ID

— —TLC2274IN TLC2274IPW

–40°C to 950 µV TLC2274AQD125°C

µ2.5 mV TLC2274QD

— — — —

–55°C to 950 µV TLC2274AMD TLC2274AMFK TLC2274AMJ TLC2274AMN125°C

µ2.5 mV TLC2274MD TLC2274MFK TLC2274MJ TLC2274MN —

† The D packages are available taped and reeled. Add R suffix to device type (e.g., TLC2274CDR).‡ The PW package is available taped and reeled.§ Chips are tested at 25°C.

1

2

3

4

8

7

6

5

1OUT1IN–1IN+

VDD–/GND

VDD+2OUT2IN–2IN+

TLC2272D, P, OR PW PACKAGE

(TOP VIEW)

1

2

3

4

5

6

7

14

13

12

11

10

9

8

1OUT1IN–1IN+

VDD+2IN+2IN–

2OUT

4OUT4IN–4IN+VDD–3IN+3IN–3OUT

3 2 1 20 19

9 10 11 12 13

4

5

6

7

8

18

17

16

15

14

4IN+NCVDD–NC3IN+

1IN+NC

VDD+NC

2IN+

1IN

–1O

UT

NC

3IN

–4I

N –

2IN

–2O

UT

NC

NC – No internal connection

3OU

T4O

UT

TLC2274D, J, N, OR PW PACKAGE

(TOP VIEW)

TLC2274FK PACKAGE(TOP VIEW)

TLC227x, TLC227xA

OPERATIO

NAL AMPLIFIERS

SLO

S190B

– FE

BR

UA

RY

1997 – RE

VIS

ED

JULY

1999

Advanced LinCM

OS

RAIL-TO-RAIL

PO

ST

OF

FIC

E B

OX

655303 DA

LLAS

, TE

XA

S 75265

•3

equivalent schematic (each amplifier)

Q3 Q6 Q9 Q12 Q14 Q16

Q2 Q5 Q7 Q8 Q10 Q11

D1

Q17Q15Q13

Q4Q1

R5

C1

VDD+

IN+

IN–

R3 R4 R1 R2

OUT

VDD –

ACTUAL DEVICE COMPONENT COUNT †

COMPONENT TLC2272 TLC2274

Transistors 38 76

Resistors 26 52

Diodes 9 18

Capacitors 3 6

† Includes both amplifiers and all ESD, bias, and trim circuitry

TLC227x, TLC227xAAdvanced LinCMOS RAIL-TO-RAILOPERATIONAL AMPLIFIERS

SLOS190B – FEBRUARY 1997 – REVISED JULY 1999


absolute maximum ratings over operating free-air temperature range (unless otherwise noted) †

Supply voltage, VDD+ (see Note 1) 8 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Supply voltage, VDD– (see Note 1) –8 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Differential input voltage, VID (see Note 2) ±16 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Input voltage, VI (any input, see Note 1) VDD– – 0.3 V to VDD+. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Input current, II (any input) ±5 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Output current, IO ±50 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Total current into VDD+ ±50 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Total current out of VDD– ±50 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Duration of short-circuit current at (or below) 25°C (see Note 3) unlimited. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous total dissipation See Dissipation Rating Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operating free-air temperature range, TA: C suffix 0°C to 70°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

I suffix –40°C to 85°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Q suffix –40°C to 125°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M suffix –55°C to 125°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Storage temperature range –65°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: D, N, P or PW package 260°C. . . . . . . . . . Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds: J package 300°C. . . . . . . . . . . . . . . . . . . . .

† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, andfunctional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is notimplied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

NOTES: 1. All voltage values, except differential voltages, are with respect to the midpoint between VDD+ and VDD –.2. Differential voltages are at IN+ with respect to IN–. Excessive current will flow if input is brought below VDD– – 0.3 V.3. The output may be shorted to either supply. Temperature and/or supply voltages must be limited to ensure that the maximum

dissipation rating is not exceeded.

DISSIPATION RATING TABLE

PACKAGETA ≤ 25°C DERATING FACTOR TA = 70°C TA = 85°C TA = 125°C

PACKAGE APOWER RATING ABOVE TA = 25°C

APOWER RATING

APOWER RATING

APOWER RATING

D–8 725 mW 5.8 mW/°C 464 mW 337 mW 145 mW

D–14 950 mW 7.6 mW/°C 608 mW 494 mW 190 mW

FK 1375 mW 11.0 mW/°C 880 mW 715 mW 275 mW

J 1375 mW 11.0 mW/°C 880 mW 715 mW 275 mW

N 1150 mW 9.2 mW/°C 736 mW 598 mW 230 mW

P 1000 mW 8.0 mW/°C 640 mW 520 mW 200 mW

PW–8 525 mW 4.2 mW/°C 336 mW 273 mW 105 mW

PW–14 700 mW 5.6 mW/°C 448 mW 364 mW —

recommended operating conditions

C SUFFIX I SUFFIX Q SUFFIX M SUFFIXUNIT

MIN MAX MIN MAX MIN MAX MIN MAXUNIT

Supply voltage, VDD± ±2.2 ±8 ±2.2 ±8 ±2.2 ±8 ±2.2 ±8 V

Input voltage range, VI VDD– VDD+ –1.5 VDD– VDD+ –1.5 VDD– VDD+ –1.5 VDD– VDD+ –1.5 V

Common-mode input voltage, VIC VDD– VDD+ –1.5 VDD– VDD+ –1.5 VDD– VDD+ –1.5 VDD– VDD+ –1.5 V

Operating free-air temperature, TA 0 70 –40 85 –40 125 –55 125 °C


OPERATIONAL AMPLIFIERS



TLC2272C electrical characteristics at specified free-air temperature, V DD = 5 V (unless otherwisenoted)

PARAMETER TEST CONDITIONS TA†TLC2272C TLC2272AC

UNITPARAMETER TEST CONDITIONS TA†MIN TYP MAX MIN TYP MAX

UNIT

VIO Input offset voltage

V 0 V 2 V

25°C 300 2500 300 950µVVIO Input offset voltage

V 0 V 2 V

Full range 3000 1500µV

αVIOTemperature coefficient

V 0 V 2 V

25°C2 2 µV/°CαVIO of input offset voltage

V 0 V 2 V

to 70°C 2 2 µV/°C

Input offset voltagelong-term drift(see Note 4)

VIC = 0,VO = 0,

VDD± = ±2.5 V,RS = 50 Ω 25°C 0.002 0.002 µV/mo

IIO Input offset current25°C 0.5 0.5

pAIIO Input offset currentFull range 100 100

pA

IIB Input bias current25°C 1 1

pAIIB Input bias currentFull range 100 100

pA

25°C0to

–0.3to

0to

–0.3to

VICRCommon-mode input

RS = 50 Ω |VIO | ≤ 5 mV

25°C to4

to4.2

to4

to4.2

VVICR voltage range RS = 50 Ω, |VIO | ≤ 5 mV0 0

V

Full range to tog3.5 3.5

IOH = –20 µA 25°C 4.99 4.99

High level output IOH = 200 µA25°C 4.85 4.93 4.85 4.93

VOHHigh-level outputvoltage

IOH = –200 µAFull range 4.85 4.85 V

voltage

IOH = 1 mA25°C 4.25 4.65 4.25 4.65

IOH = –1 mAFull range 4.25 4.25

VIC = 2.5 V, IOL = 50 µA 25°C 0.01 0.01

Low level output VIC = 2 5 V IOL = 500 µA25°C 0.09 0.15 0.09 0.15

VOLLow-level outputvoltage

VIC = 2.5 V, IOL = 500 µAFull range 0.15 0.15 V

voltage

VIC = 2 5 V IOL = 5 A25°C 0.9 1.5 0.9 1.5

VIC = 2.5 V, IOL = 5 AFull range 1.5 1.5

Large signal differential V 2 5 V RL 10 kΩ‡ 25°C 15 35 15 35

AVDLarge-signal differentialvoltage amplification

VIC = 2.5 V,VO = 1 V to 4 V

RL = 10 kΩ‡Full range 15 15 V/mVVD voltage am lification VO = 1 V to 4 V

RL = 1 mΩ‡ 25°C 175 175

ridDifferential inputresistance

25°C 1012 1012 Ω

riCommon-mode inputresistance

25°C 1012 1012 Ω

ciCommon-mode inputcapacitance

f = 10 kHz, P package 25°C 8 8 pF

zoClosed-loop outputimpedance

f = 1 MHz, AV = 10 25°C 140 140 Ω

CMRRCommon-mode VIC = 0 to 2.7 V, 25°C 70 75 70 75

dBCMRR rejection ratioIC ,

VO = 2.5 V, RS = 50 Ω Full range 70 70dB

kSVRSupply-voltage rejection VDD = 4.4 V to 16 V, 25°C 80 95 80 95

dBkSVRy g j

ratio (∆VDD/∆VIO)DD

VIC = VDD/2, No load Full range 80 80dB

IDD Supply current VO = 2 5 V No load25°C 2.2 3 2.2 3

mAIDD Supply current VO = 2.5 V, No loadFull range 3 3

mA

† Full range is 0°C to 70°C.‡ Referenced to 2.5 VNOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated

to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.




TLC2272C operating characteristics at specified free-air temperature, V DD = 5 V



UNIT

Slew rate at unityVO = 0.5 V to 2.5 V,

‡ ‡25°C 2.3 3.6 2.3 3.6

SRSlew rate at unitygain

RL = 10 kΩ‡, CL = 100 pF‡Full

1 7 1 7V/µsg

range1.7 1.7

VEquivalent input f = 10 Hz 25°C 50 50

nV/√HzVnq

noise voltage f = 1 kHz 25°C 9 9nV/√Hz

VNPP

Peak-to-peakequivalent input

f = 0.1 Hz to 1 Hz 25°C 1 1µVVNPP equivalent input

noise voltage f = 0.1 Hz to 10 Hz 25°C 1.4 1.4µV

InEquivalent inputnoise current

25°C 0.6 0.6 fA/√Hz

T t l h iVO = 0.5 V to 2.5 V, AV = 1 0.0013% 0.0013%

THD + NTotal harmonicdistortion plus noise

VO = 0.5 V to 2.5 V,f = 20 kHz,

‡AV = 10 25°C 0.004% 0.004%

distortion lus noiseRL = 10 kΩ‡, AV = 100 0.03% 0.03%

Gain-bandwidthproduct

f = 10 kHz, CL = 100 pF‡

RL = 10 kΩ‡, 25°C 2.18 2.18 MHz

BOM

Maximumoutput-swingbandwidth

VO(PP) = 2 V, RL = 10 kΩ‡,

AV = 1, CL = 100 pF‡ 25°C 1 1 MHz

AV = –1, To 0 1% 1 5 1 5t Settling time

AV = 1,Step = 0.5 V to 2.5 V,

To 0.1%25°C

1.5 1.5µsts Settling time ,

RL = 10 kΩ‡,‡ To 0 01%

25°C2 6 2 6

µsL

CL = 100 pF‡ To 0.01% 2.6 2.6

φmPhase margin atunity gain RL = 10 kΩ‡, CL = 100 pF‡

25°C 50° 50°

Gain marginL , L

25°C 10 10 dB† Full range is 0°C to 70°C.‡ Referenced to 2.5 V





TLC2272C electrical characteristics at specified free-air temperature, V DD± = ±5 V (unlessotherwise specified)



UNIT


V 0 V 0


V 0 V 0


αVIOTemperature coefficient of

V 0 V 0

25°C2 2 µV/°CαVIO input offset voltage

V 0 V 0

to 70°C 2 2 µV/°C


VIC = 0,RS = 50 Ω

VO = 0,25°C 0.002 0.002 µV/mo



pA



pA

–5 –5.3 –5 –5.325°C to to to to


RS = 50 Ω |VIO | ≤5 mV4 4.2 4 4.2

VVICR voltage range RS = 50 Ω, |VIO | ≤5 mV–5 –5

V


IO = –20 µA 25°C 4.99 4.99

Maximum positive peak IO = 200 µA25°C 4.85 4.93 4.85 4.93

VOM+Maximum positive peakoutput voltage

IO = –200 µAFull range 4.85 4.85 V

out ut voltage

IO = 1 mA25°C 4.25 4.65 4.25 4.65

IO = –1 mAFull range 4.25 4.25

VIC = 0, IO = 50 µA 25°C –4.99 –4.99

Maximum negative peak VIC = 0 IO = 500 µA25°C –4.85 –4.91 –4.85 –4.91

VOM–Maximum negative peakoutput voltage

VIC = 0, IO = 500 µAFull range –4.85 –4.85 V

out ut voltage

VIC = 0 IO = 5 A25°C –3.5 –4.1 –3.5 –4.1

VIC = 0, IO = 5 AFull range –3.5 –3.5

Large signal differential RL = 10 kΩ25°C 25 50 25 50


VO = ±4 VRL = 10 kΩ

Full range 25 25 V/mVvoltage am lification

RL = 1 mΩ 25°C 300 300


25°C 1012 1012 Ω


25°C 1012 1012 Ω




f = 1 MHz, AV = 10 25°C 130 130 Ω

CMRRCommon-mode rejection VIC = –5 to 2.7 V, 25°C 75 80 75 80

dBCMRRj

ratioIC ,

VO = 0 V, RS = 50 Ω Full range 75 75dB

kSVRSupply-voltage rejection VDD± = 2.2 V to ±8 V, 25°C 80 95 80 95

dBkSVRy g j

ratio (∆VDD± /∆VIO)DD±

VIC = 0, No load Full range 80 80dB

IDD Supply current VO = 0 V No load25°C 2.4 3 2.4 3

mAIDD Supply current VO = 0 V No loadFull range 3 3

mA

† Full range is 0°C to 70°C.NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated





TLC2272C operating characteristics at specified free-air temperature, V DD± = ±5 V



UNIT

Slew rate at VO = ±2 3 V RL = 10 kΩ25°C 2.3 3.6 2.3 3.6

SRSlew rate atunity gain

VO = ±2.3 V,CL = 100 pF

RL = 10 kΩ,Full

1 7 1 7V/µsunity gain CL = 100 F

range1.7 1.7


nV/√HzVnq


VNPP





25°C 0.6 0.6 fA/√Hz

Total harmonic VO = ±2.3 V, AV = 1 0.0011% 0.0011%

THD + NTotal harmonicdistortion pulse

VO = ±2.3 V,f = 20 kHz, AV = 10 25°C 0.004% 0.004%

duration RL = 10 kΩ AV = 100 0.03% 0.03%

Gain-bandwidth f = 10 kHz, RL = 10 kΩ,25°C 2 25 2 25 MHz

product,

CL = 100 pFL ,

25°C 2.25 2.25 MHz

BOMMaximum output- VO(PP) = 4.6 V, AV = 1,

25°C 0 54 0 54 MHzBOM swing bandwidthO(PP) ,

RL = 10 kΩ,V ,

CL = 100 pF25°C 0.54 0.54 MHz


AV = 1,Step = –2.3 V to 2.3 V,

To 0.1%25°C


RL = 10 kΩ,To 0 01%

25°C3 2 3 2

µsL

CL = 100 pF To 0.01% 3.2 3.2

φmPhase margin atunity gain RL = 10 kΩ, CL = 100 pF

25°C 52° 52°

Gain marginL L

25°C 10 10 dB† Full range is 0°C to 70°C.





TLC2274C electrical characteristics at specified free-air temperature, V DD = 5 V (unless otherwisenoted)

PARAMETER TEST CONDITIONS T †TLC2274C TLC2274AC


UNIT

VIO Input offset voltage25°C 300 2500 300 950

µVVIO Input offset voltageFull range 3000 1500

µV

αVIOTemperature coefficientof input offset voltage

25°Cto 70°C 2 2 µV/°C


VDD± = ±2.5 V,VO = 0,

VIC = 0,RS = 50 Ω

25°C 0.002 0.002 µV/mo



pA



pA


RS = 50Ω VIO ≤ 5 m V

25°C0to4

–0.3to

4.2

0to4

–0.3to

4.2VVICR voltage range RS = 50Ω, VIO ≤ 5 m V,

Full range0to

3.5

0to

3.5

V

IOH = –20 µA 25°C 4.99 4.99




voltage

IOH = 1 mA25°C 4.25 4.65 4.25 4.65


VIC = 2.5 V, IOL = 50 µA 25°C 0.01 0.01

Low level outputVIC = 2.5 V, 25°C 0.09 0.15 0.09 0.15

VOLLow-level output voltage

ICIOL = 500 µA Full range 0.15 0.15 V

voltage

VIC = 2 5 V IOL = 5 A25°C 0.9 1.5 0.9 1.5




VIC = 2.5 V,VO = 1 V to 4 V


RL = 1 mΩ‡ 25°C 175 175


25°C 1012 1012 Ω


25°C 1012 1012 Ω


f = 10 kHz, N package 25°C 8 8 pF


f = 1 MHz, AV = 10 25°C 140 140 Ω


dBCMRR rejection ratioIC

VO = 2.5 V, RS = 50Ω Full range 70 70dB


dBkSVRy g j





mA

† Full range is 0°C to 70°C.‡ Referenced to 2.5 VNOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated





TLC2274C operating characteristics at specified free-air temperature, V DD = 5 V



UNIT

Slew rate at VO 0 5 V to 2 5 V25°C 2.3 3.6 2.3 3.6


VO = 0.5 V to 2.5 V,RL = 10 kΩ‡ CL = 100 pF‡ Full

1 7 1 7V/µsunity gain RL = 10 kΩ‡, CL = 100 F‡

range1.7 1.7


nV/√HzVnq


VN(PP)

Peak-to-peak equivalent input

f = 0.1 to 1 Hz 25°C 1 1µVVN(PP) equivalent input

noise voltage f = 0.1 to 10 Hz 25°C 1.4 1.4µV


25°C 0.6 0.6 fA /√Hz

Total harmonic VO = 0.5 V to 2.5 V, AV = 1 0.0013% 0.0013%

THD + NTotal harmonicdistortion plus

VO = 0.5 V to 2.5 V,f = 20 kHz,

‡AV = 10 25°C 0.004% 0.004%

noise RL = 10 kΩ‡AV = 100 0.03% 0.03%

Gain-bandwidthproduct

f = 10 kHz,CL = 100 pF‡

RL = 10 kΩ‡, 25°C 2.18 2.18 MHz

BOM

Maximumoutput-swingbandwidth

VO(PP) = 2 V,RL = 10 kΩ‡,

AV = 1, CL = 100 pF‡ 25°C 1 1 MHz

AV = –1, To 0 1% 1 5 1 5

t Settling time

AV = 1,Step = 0.5 V to 2.5 V,

To 0.1%25°C

1.5 1.5µsts Settling time

,RL = 10 kΩ‡,

‡ To 0 01%25°C

2 6 2 6µs

CL = 100 pF‡ To 0.01% 2.6 2.6


25°C 50° 50°

Gain marginL , L

25°C 10 10 dB† Full range is 0°C to 70°C.‡ Referenced to 2.5 V





TLC2274C electrical characteristics at specified free-air temperature, V DD± = ±5 V (unlessotherwise noted)



UNIT



µV

αVIOTemperature coefficient of input 25°C

2 2 µV/°CαVIO offset voltage to 70°C 2 2 µV/°C

Input offset voltage long-termdrift (see Note 4)

VIC = 0,RS = 50 Ω

VO = 0, 25°C 0.002 0.002 µV/mo



pA



pA


RS = 50 Ω |VIO | ≤ 5 mV

25°C–5to4

–5.3to

4.2

–5to4

–5.3to

4.2VVICR voltage range RS = 50 Ω, |VIO | ≤ 5 mV

Full range–5to

3.5

–5to

3.5

V

IO = –20 µA 25°C 4.99 4.99

Maximum positive peak output IO = 200 µA25°C 4.85 4.93 4.85 4.93

VOM+Maximum positive peak outputvoltage

IO = –200 µAFull range 4.85 4.85 Vvoltage

IO = 1 mA25°C 4.25 4.65 4.25 4.65


VIC = 0, IO = 50 µA 25°C–4.9

9–4.9

9

VMaximum negative peak output VIC = 0 IO = 500 µA

25°C–4.8

5–4.9

1–4.8

5–4.9

1VVOM–

Maximum negative eak out utvoltage

VIC = 0, IO = 500 µA

Full range–4.8

5–4.8

5

V

VIC = 0 IO = 5 mA25°C –3.5 –4.1 –3.5 –4.1

VIC = 0, IO = –5 mAFull range –3.5 –3.5

Large signal differential voltage RL = 10 kΩ25°C 25 50 25 50

AVDLarge-signal differential voltageamplification VO = ±4 V

RL = 10 kΩFull range 25 25 V/mVam lification

RL = 1 MΩ 25°C 300 300

rid Differential input resistance 25°C 1012 1012 Ω

ri Common-mode input resistance 25°C 1012 1012 Ω



zo Closed-loop output impedance f = 1 MHz, AV = 10 25°C 130 130 Ω

CMRR Common mode rejection ratioVIC = –5 V to 2.7 V, 25°C 75 80 75 80

dBCMRR Common-mode rejection ratio ICVO = 0, RS = 50 Ω Full range 75 75

dB

kSVRSupply-voltage rejection ratio VDD± = ±2.2 V to ±8 V, 25°C 80 95 80 95

dBkSVRy g j

(∆VDD± /∆VIO)DD±


IDD Supply current VO = 0 No load25°C 4.8 6 4.8 6

mAIDD Supply current VO = 0, No loadFull range 6 6

mA

† Full range is 0°C to 70°C.NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated





TLC2274C operating characteristics at specified free-air temperature, V DD± = ±5 V



UNIT

Slew rate at unity VO = ±2 3 V RL = 10 kΩ25°C 2.3 3.6 2.3 3.6


VO = ±2.3 V,CL = 100 pF

RL = 10 kΩ,Full

1 7 1 7V/µsgain CL = 100 F

range1.7 1.7


nV/√HzVnq

noise voltage f = 1 Hz 25°C 9 9nV/√Hz

VN(PP)


f = 0.1 Hz to 1 Hz 25°C 1 1µVVN(PP) equivalent input



25°C 0.6 0.6 fA /√Hz



VO = ±2.3 V,f = 20 kHz, AV = 10 25°C 0.004% 0.004%

noise RL = 10 kΩ AV = 100 0.03% 0.03%

Gain-bandwidth f = 10 kHz, RL= 10 kΩ,25°C 2 25 2 25 MHz

product,

CL = 100 pFL ,

25°C 2.25 2.25 MHz

BOM

Maximum output swing

VO(PP) = 4.6 V, AV = 1,25°C 0 54 0 54 MHzBOM output-swing

bandwidth

O(PP)RL = 10 kΩ,

VCL = 100 pF

25°C 0.54 0.54 MHz

AV = –1, To 0 1% 1 5 1 5

t Settling time

AV = 1,Step = –2.3 V to 2.3 V,

To 0.1%25°C


RL = 10 kΩ,To 0 01%

25°C3 2 3 2

µsL

CL = 100 pF To 0.01% 3.2 3.2


25°C 52° 52°

Gain marginL L

25°C 10 10 dB† Full range is 0°C to 70°C.





TLC2272I electrical characteristics at specified free-air temperature, V DD = 5 V (unless otherwisenoted)

PARAMETER TEST CONDITIONS TA†TLC2272I TLC2272AI


UNIT


V 0 V 2 V


V 0 V 2 V


αVIOTemperature coefficient

V 0 V 2 V

25°C2 2 µV/°CαVIO of input offset voltage

VIC 0 VDD ±2 5Vto 85°C 2 2 µV/°C


VIC = 0,VO = 0,

VDD± = ±2.5V RS = 50 Ω

25°C 0.002 0.002 µV/mo



pA



pA

0 –0.3 0 –0.325°C to to to to

VICRCommon-mode input 4 4.2 4 4.2

VVICR voltage range RS = 50 Ω, |VIO | ≤5 mV 0 0V


IOH = –20 µA 25°C 4.99 4.99




voltage

IOH = 1 mA25°C 4.25 4.65 4.25 4.65


VIC = 2.5 V, IOL = 50 µA 25°C 0.01 0.01

Low level output VIC = 2 5 V IOL = 500 µA25°C 0.09 0.15 0.09 0.15


VIC = 2.5 V, IOL = 500 µAFull range 0.15 0.15 V

voltage

VIC = 2 5 V IOL = 5 A25°C 0.9 1.5 0.9 1.5




VIC = 2.5 V,VO = 1 V to 4 V


RL = 1 mΩ‡ 25°C 175 175


25°C 1012 1012 Ω


25°C 1012 1012 Ω




f = 1 MHz, AV = 10 25°C 140 140 Ω





dBkSVRy g j





mA

† Full range is – 40°C to 85°C.‡ Referenced to 2.5 VNOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated





TLC2272I operating characteristics at specified free-air temperature, V DD = 5 V



UNIT

Slew rate at VO = 0 5 V to 2 5 V25°C 2.3 3.6 2.3 3.6


VO = 0.5 V to 2.5 V,RL = 10 kΩ‡, CL = 100 pF‡ Full


range1.7 1.7


nV√HzVnq

noise voltage f = 1 kHz 25°C 9 9nV√Hz

VNPP





25°C 0.6 0.6 fA√Hz



VO = 0.5 V to 2.5 V,f = 20 kHz,

‡AV = 10 25°C 0.004% 0.004%

noise RL = 10 kΩ‡AV = 100 0.03% 0.03%

Gain-bandwidth f = 10 kHz, RL = 10 kΩ‡,25°C 2 18 2 18 MHz

product,

CL = 100 pF‡L ,

25°C 2.18 2.18 MHz

BOMMaximum output- VO(PP) = 2 V, AV = 1,

25°C 1 1 MHzBOM swing bandwidthO(PP) ,

RL = 10 kΩ‡,V ,

CL = 100 pF‡ 25°C 1 1 MHz

AV = –1 To 0 1% 1 5 1 5

t Settling time

AV = –1,Step = 0.5 V to 2.5 V,

To 0.1%

25°C1.5 1.5

sts Settling time Ste 0.5 V to 2.5 V,RL = 10 kΩ‡,

‡To

25°C2 6 2 6

µsL

CL = 100 pF‡ 0.01%2.6 2.6


25°C 50° 50°

Gain marginL , L

25°C 10 10 dB

† Full range is – 40°C to 85°C.‡ Referenced to 2.5 V





TLC2272I electrical characteristics at specified free-air temperature, V DD± = ±5 V (unless otherwisenoted)



UNIT


V 0 V 0


V 0 V 0


αVIOTemperature coefficientof input offset voltage

V 0 V 0

25°Cto 85°C 2 2 µV/°C


VIC = 0,RS = 50 Ω

VO = 0, 25°C 0.002 0.002 µV/mo



pA



pA


RS = 50 Ω |VIO | ≤5 mV

25°C–5to4

–5.3to

4.2

–5to4

–5.3to

4.2VVICR voltage range RS = 50 Ω, |VIO | ≤5 mV

Full range–5to

3.5

–5to

3.5

V

IO = –20 µA 25°C 4.99 4.99




out ut voltage

IO = 1 mA25°C 4.25 4.65 4.25 4.65


VIC = 0, IO = 50 µA 25°C –4.99 –4.99

Maximum negative VIC = 0 IO = 500 µA25°C –4.85 –4.91 –4.85 –4.91

VOM–Maximum negativepeak output voltage


eak out ut voltage

VIC = 0 IO = 5 A25°C –3.5 –4.1 –3.5 –4.1


Large-signal RL = 10 kΩ25°C 25 50 25 50

AVD

Large signal differential voltage VO = ±4 V

RL = 10 kΩFull range 25 25 V/mV

amplification RL = 1 mΩ 25°C 300 300


25°C 1012 1012 Ω


25°C 1012 1012 Ω




f = 1 MHz, AV = 10 25°C 130 130 Ω


dBCMRR rejection ratioIC ,


kSVR

Supply-voltagerejection ratio

VDD = 4.4 V to 16 V, 25°C 80 95 80 95dBkSVR rejection ratio

(∆VDD± /∆VIO)

DD ,VIC = VDD/2, No load Full range 80 80

dB



mA

† Full range is – 40°C to 85°C.NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated





TLC2272I operating characteristics at specified free-air temperature, V DD± = ±5 V



UNIT

Slew rate at VO = ±2 3 V RL = 10 kΩ25°C 2.3 3.6 2.3 3.6


VO = ±2.3 V,CL = 100 pF

RL = 10 kΩ,Full

1 7 1 7V/µsy g CL 100 F

range1.7 1.7


nV√HzVnq

noise voltage f = 1 kHz 25°C 9 9nV√Hz

VNPP





25°C 0.6 0.6 fA√Hz

Total harmonic VO = ±2.3 V AV = 1 0.0011% 0.0011%


VO = ±2.3 VRL = 10 kΩ, AV = 10 25°C 0.004% 0.004%

noise f = 20 kHz AV = 100 0.03% 0.03%

Gain-bandwidth f =10 kHz, RL = 10 kΩ,25°C 2 25 2 25 MHz

product,

CL = 100 pFL ,

25°C 2.25 2.25 MHz

BOM

Maximumoutput swing


bandwidth

O(PP) ,RL = 10 kΩ,

V ,CL = 100 pF

25°C 0.54 0.54 MHz


AV = 1,Step = –2.3 V to 2.3 V,

To 0.1%25°C


RL = 10 kΩ,To 0 01%

25°C3 2 3 2

µsL

CL = 100 pF To 0.01% 3.2 3.2


25°C 52° 52°

Gain marginL L

25°C 10 10 dB† Full range is –40°C to 85°C.





TLC2274I electrical characteristics at specified free-air temperature, V DD = 5 V (unless otherwisenoted)

PARAMETER TEST CONDITIONS T †TLC2274I TLC2274AI


UNIT



µV

αVIOTemperature coefficient of 25°C

2 2 µV/°CαVIO input offset voltage to 85°C 2 2 µV/°C

Input offset voltagelong-term drift (see Note 4)

VDD± = ±2.5 V,VO = 0,

VIC = 0,RS = 50 Ω

25°C 0.002 0.002 µV/mo



pA



pA


RS = 50 Ω |VIO | ≤ 5 mV

25°C0to4

–0.3to

4.2

0to4

–0.3to

4.2VVICR voltage range RS = 50 Ω, |VIO | ≤ 5 mV

Full range0to

3.5

0to

3.5

V

IOH = –20 µA 25°C 4.99 4.99

IOH = 200 µA25°C 4.85 4.93 4.85 4.93

VOH High-level output voltageIOH = –200 µA

Full range 4.85 4.85 V

IOH = 1 mA25°C 4.25 4.65 4.25 4.65


VIC = 2.5 V, IOL = 50 µA 25°C 0.01 0.01

VIC = 2 5 V IOL = 500 µA25°C 0.09 0.15 0.09 0.15

VOL Low-level output voltageVIC = 2.5 V, IOL = 500 µA


VIC = 2 5 V IOL = 5 A25°C 0.9 1.5 0.9 1.5


L i l diff ti l V 2 5 V RL = 10 kΩ‡25°C 15 35 15 35


VIC = 2.5 V,VO = 1 V to 4 V

RL = 10 kΩ‡Full range 15 15 V/mV

voltage am lification VO = 1 V to 4 VRL = 1 MΩ‡ 25°C 175 175



25°C 1012 1012 Ω




f = 1 MHz, AV = 10 25°C 140 140 Ω

CMRRCommon-mode rejection VIC = 0 to 2.7 V, 25°C 70 75 70 75

dBCMRRj

ratioIC



dBkSVRy g j

ratio (∆VDD /∆VIO)DD




mA

† Full range is – 40°C to 85°C.‡ Referenced to 2.5 VNOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated





TLC2274I operating characteristics at specified free-air temperature, V DD = 5 V



UNIT

Slew rate at unity VO 0 5 V to 2 5 V25°C 2.3 3.6 2.3 3.6



1 7 1 7V/µs

gain RL = 10 kΩ‡, CL = 100 F‡range

1.7 1.7


nV/√HzVnq


VN(PP)





25°C 0.6 0.6 fA /√Hz

T t l h iVO = 0.5 V to 2.5 V, AV = 1 0.0013% 0.0013%

THD + NTotal harmonicdistortion plus noise

VO = 0.5 V to 2.5 V,f = 20 kHz,

‡AV = 10 25°C 0.004% 0.004%

distortion lus noiseRL = 10 kΩ‡

AV = 100 0.03% 0.03%


product,

CL = 100 pF‡L ,

25°C 2.18 2.18 MHz

BOM

Maximumoutput swing

VO(PP) = 2 V, AV = 1,25°C 1 1 MHzBOM output-swing

bandwidth

O(PP)RL = 10 kΩ‡,

VCL = 100 pF‡ 25°C 1 1 MHz


AV = 1,Step = 0.5 V to 2.5 V,

To 0.1%25°C


RL = 10 kΩ‡,‡ To 0 01%

25°C2 6 2 6

µsL

CL = 100 pF‡ To 0.01% 2.6 2.6


25°C 50° 50°

Gain marginL , L

25°C 10 10 dB† Full range is – 40°C to 85°C.‡ Referenced to 2.5 V





TLC2274I electrical characteristics at specified free-air temperature, V DD± = ±5 V (unless otherwisenoted)



UNIT



µV




VIC = 0,RS = 50 Ω

VO = 0, 25°C 0.002 0.002 µV/mo



pA



pA


RS = 50 Ω VIO | ≤ 5 mV

25°C–5to4

–5.3to

4.2

–5to4

–5.3to

4.2VVICR voltage range RS = 50 Ω, VIO | ≤ 5 mV

Full range–5to

3.5

–5to

3.5

V

IO = –20 µA 25°C 4.99 4.99



IO = –200 µAFull range 4.85 4.85 Vout ut voltage

IO = 1 mA25°C 4.25 4.65 4.25 4.65


VIC = 0, IO = 50 µA 25°C –4.99 –4.99



VIC = 0, IO = 500 µAFull range –4.85 –4.85 Vout ut voltage

VIC = 0 IO = 5 A25°C –3.5 –4.1 –3.5 –4.1



AVDLarge-signal differentialvoltage amplification VO = ±4 V

RL = 10 kΩFull range 25 25 V/mVvoltage am lification

RL = 1 MΩ 25°C 300 300



25°C 1012 1012 Ω




f = 1 MHz, AV = 10 25°C 130 130 Ω


dBCMRRj

ratioIC

VO = 0, RS = 50 Ω Full range 75 75dB

kSVRSupply-voltage rejection VDD± = ±2.2 V to ±8 V, 25°C 80 95 80 95

dBkSVRy g j

ratio (∆VDD± /∆VIO)DD±




mA

† Full range is – 40°C to 85°C.NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated





TLC2274I operating characteristics at specified free-air temperature, V DD± = ±5 V



UNIT



VO = ±2.3 V,CL = 100 pF

RL = 10 kΩ,Full

1 7 1 7V/µsgain CL = 100 F

range1.7 1.7


nV/√HzVnq


VN(PP)

Peak-to-peak equivalent input




25°C 0.6 0.6 fA/√Hz



VO = ±2.3 V,RL = 10 kΩ, AV = 10 25°C 0.004% 0.004%

noise f = 20 kHz AV = 100 0.03% 0.03%


product,

CL = 100 pFL ,

25°C 2.25 2.25 MHz

BOMMaximum output- VO(PP) = 4.6 V, AV = 1,

25°C 0 54 0 54 MHzBOM swing bandwidthO(PP)

RL = 10 kΩ,V

CL = 100 pF25°C 0.54 0.54 MHz


AV = 1,Step = –2.3 V to 2.3 V,

To 0.1%25°C


RL = 10 kΩ,To 0 01%

25°C3 2 3 2

µsL

CL = 100 pF To 0.01% 3.2 3.2


25°C 52° 52°

Gain marginL L

25°C 10 10 dB† Full range is –40°C to 85°C.





TLC2272Q and TLC2272M electrical characteristics at specified free-air temperature, V DD = 5 V(unless otherwise noted)

PARAMETER TEST CONDITIONS TA†TLC2272Q,TLC2272M

TLC2272AQ,TLC2272AM UNITA

MIN TYP MAX MIN TYP MAX



µV

αVIOTemperature coefficient 25°C

2 2 µV/°CαVIO of input offset voltage to 125°C 2 2 µV/°C

Input offset voltage long-term drift (see Note 4)

VIC = 0,VO = 0,

VDD± = ±2.5 V,RS = 50 Ω 25°C 0.002 0.002 µV/mo



pA



pA


RS = 50 Ω |VIO | ≤5 mV

25°C0to4

–0.3to

4.2

0to4

–0.3to

4.2VVICR voltage range RS = 50 Ω, |VIO | ≤5 mV

Full range0to

3.5

0to

3.5

V

IOH = –20 µA 25°C 4.99 4.99




voltage

IOH = 1 mA25°C 4.25 4.65 4.25 4.65


VIC = 2.5 V, IOL = 50 µA 25°C 0.01 0.01

VIC = 2 5 V IOL = 500 µA25°C 0.09 0.15 0.09 0.15

VOL Low-level output voltageVIC = 2.5 V, IOL = 500 µA


VIC = 2 5 V IOL = 5 A25°C 0.9 1.5 0.9 1.5


Large-signal V 2 5 V RL 10 kΩ‡ 25°C 10 35 10 35

AVD

Large signal differential voltage

VIC = 2.5 V,VO = 1 V to 4 V

RL = 10 kΩ‡Full range 10 10 V/mVVD

amplificationVO = 1 V to 4 V

RL = 1 mΩ‡ 25°C 175 175


25°C 1012 1012 Ω


25°C 1012 1012 Ω




f = 1 MHz, AV = 10 25°C 140 140 Ω

CMRRCommon-mode rejection VIC = 0 to 2.7 V, 25°C 70 75 70 75

dBCMRRj

ratioIC



dBkSVRy g j





mA

† Full range is –40°C to 125°C for Q level part, –55°C to 125°C for M level part.‡ Referenced to 2.5 VNOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated





TLC2272Q and TLC2272M operating characteristics at specified free-air temperature, V DD = 5 V




Slew rate at VO = 1 25 V to 2 75 V25°C 2.3 3.6 2.3 3.6


VO = 1.25 V to 2.75 V, RL = 10 kΩ‡, CL = 100 pF‡ Full


range1.7 1.7


nV/√HzVnq


VNPP





25°C 0.6 0.6 fA/√Hz



VO = 0.5 V to 2.5 V,f = 20 kHz,

‡AV = 10 25°C 0.004% 0.004%

noise RL = 10 kΩ‡, AV = 100 0.03% 0.03%

Gain-bandwidth f =10 kHz, RL = 10 kΩ‡,25°C 2 18 2 18 MHz

product,

CL = 100 pF‡L ,

25°C 2.18 2.18 MHz



RL = 10 kΩ‡,V ,

CL = 100 pF‡ 25°C 1 1 MHz


AV = 1,Step = 0.5 V to 2.5 V,

To 0.1%25°C


RL = 10 kΩ‡,‡ To 0 01%

25°C2 6 2 6

µsL

CL = 100 pF‡ To 0.01% 2.6 2.6


25°C 50° 50°

Gain marginL , L

25°C 10 10 dB† Full range is –40°C to 125°C for Q level part, –55°C to 125°C for M level part.‡ Referenced to 2.5 V





TLC2272Q and TLC2272M electrical characteristics at specified free-air temperature, V DD± = ±5 V(unless otherwise noted)






µV




VIC = 0,RS = 50 Ω

VO = 0,25°C 0.002 0.002 µV/mo



pA



pA

–5 –5.3 –5 –5.325°C to to to to


RS = 50 Ω |VIO | ≤5 mV4 4.2 4 4.2

VVICR voltage range RS = 50 Ω, |VIO | ≤5 mV–5 –5

V


IO = –20 µA 25°C 4.99 4.99




out ut voltage

IO = 1 mA25°C 4.25 4.65 4.25 4.65


VIC = 0, IO = 50 µA 25°C –4.99 –4.99




out ut voltage

VIC = 0 IO = 5 A25°C –3.5 –4.1 –3.5 –4.1




VO = ±4 VRL = 10 kΩ


RL = 1 mΩ 25°C 300 300



25°C 1012 1012 Ω




f = 1 MHz, AV = 10 25°C 130 130 Ω


dBCMRRj

ratioIC

VO = 0 V, RS = 50 Ω Full range 75 75dB

kSVRSupply-voltage rejection VDD = ±2.2 V to ±8 V, 25°C 80 95 80 95

dBkSVRy g j

ratio (∆VDD± /∆VIO)DD




mA

† Full range is –40°C to 125°C for Q level part, –55°C to 125°C for M level part.NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated





TLC2272Q and TLC2272M operating characteristics at specified free-air temperature, VDD± = ±5 V




Slew rate at VO = ±1 V RL = 10 kΩ25°C 2.3 3.6 2.3 3.6


VO = ±1 V, RL = 10 kΩ,CL = 100 pF Full

1 7 1 7V/µsunity gain CL = 100 F

range1.7 1.7


nV/√HzVnq


VNPP





25°C 0.6 0.6 fA/√Hz

Total harmonic VO = ±2.3 V AV = 1 0.0011% 0.0011%


VO = ±2.3 VRL = 10 kΩ, AV = 10 25°C 0.004% 0.004%

noise f = 20 kHz AV = 100 0.03% 0.03%

Gain-bandwidth f =10 kHz, RL = 10 kΩ,25°C 2 25 2 25 MHz

product,

CL = 100 pFL ,

25°C 2.25 2.25 MHz

BOM

Maximumoutput swing


bandwidth

O(PP) ,RL = 10 kΩ,

V ,CL = 100 pF

25°C 0.54 0.54 MHz


AV = 1,Step = –2.3 V to 2.3 V,

To 0.1%25°C


RL = 10 kΩ,To 0 01%

25°C3 2 3 2

µsL

CL = 100 pF To 0.01% 3.2 3.2


25°C 52° 52°

Gain marginL L

25°C 10 10 dB† Full range is –40°C to 125°C for Q level part, –55°C to 125°C for M level part.





TLC2274Q and TLC2274M electrical characteristics at specified free-air temperature, V DD = 5 V(unless otherwise noted)






µV

αVIOTemperature coefficient 25°C

2 2 µV/°CαVIO of input offset voltage to 125°C 2 2 µV/°C


VDD± = ±2.5 V,VO = 0,

VIC = 0,RS = 50 Ω 25°C 0.002 0.002 µV/mo



pA



pA

0 –0.3 0 –0.325°C to to to to


RS = 50 Ω |VIO | ≤ 5 mV4 4.2 4 4.2

VVICR voltage range RS = 50 Ω, |VIO | ≤ 5 mV0 0

V


IOH = –20 µA 25°C 4.99 4.99


VOHHigh-level output voltage


voltage

IOH = 1 mA25°C 4.25 4.65 4.25 4.65


VIC = 2.5 V, IOL = 50 µA 25°C 0.01 0.01

Low level outputVIC = 2.5 V, 25°C 0.09 0.15 0.09 0.15


ICIOL = 500 µA Full range 0.15 0.15 V

voltage

VIC = 2 5 V IOL = 5 A25°C 0.9 1.5 0.9 1.5




VIC = 2.5 V,VO = 1 V to 4 V


RL = 1 MΩ‡ 25°C 175 175


25°C 1012 1012 Ω


25°C 1012 1012 Ω




f = 1 MHz, AV = 10 25°C 140 140 Ω




kSVRSupply-voltage rejection VDD = 4.4 V to 16, 25°C 80 95 80 95

dBkSVRy g j



† Full range is –40°C to 125°C for Q level part, –55°C to 125°C for M level part.‡ Referenced to 2.5 VNOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated





TLC2274Q and TLC2274M electrical characteristics at specified free-air temperature, V DD = 5 V(unless otherwise noted) (continued)






mA

† Full range is –40°C to 125°C for Q level part, –55°C to 125°C for M level part.

TLC2274Q and TLC2274M operating characteristics at specified free-air temperature, V DD = 5 V




Slew rate at unity VO 0 5 V to 2 5 V25°C 2.3 3.6 2.3 3.6



1 7 1 7V/µs

gain RL = 10 kΩ‡, CL = 100 F‡range

1.7 1.7


nV/√HzVnq


VN(PP)





25°C 0.6 0.6 fA /√Hz



VO = 0.5 V to 2.5 V,f = 20 kHz,

‡AV = 10 25°C 0.004% 0.004%

noise RL = 10 kΩ‡AV = 100 0.03% 0.03%


product,

CL = 100 pF‡L ,

25°C 2.18 2.18 MHz



RL = 10 kΩ‡,V ,

CL = 100 pF‡ 25°C 1 1 MHz


AV = 1,Step = 0.5 V to 2.5 V,

To 0.1%25°C


RL = 10 kΩ‡,‡ To 0 01%

25°C2 6 2 6

µsL

CL = 100 pF‡ To 0.01% 2.6 2.6


25°C 50° 50°

Gain marginL , L

25°C 10 10 dB

† Full range is –40°C to 125°C for Q level part, –55°C to 125°C for M level part.‡ Referenced to 2.5 V





TLC2274Q and TLC2274M electrical characteristics at specified free-air temperature, V DD± = ±5 V(unless otherwise noted)






µV



Input offset voltage long-term drift (see Note 4)

VIC = 0,RS = 50 Ω

VO = 0, 25°C 0.002 0.002 µV/mo



pA



pA

–5 –5.3 –5 –5.325°C

5to

5.3to

5to

5.3to


RS = 50 Ω |VIO | ≤ 5 mV4 4.2 4 4.2

VVICR voltage rangeRS = 50 Ω, |VIO | ≤ 5 mV

–5 –5V

Full range5to

5tog

3.5 3.5

IO = –20 µA 25°C 4.99 4.99

M i iti k IO = 200 µA25°C 4.85 4.93 4.85 4.93



out ut voltage

IO = 1 mA25°C 4.25 4.65 4.25 4.65


VIC = 0, IO = 50 µA 25°C –4.99 –4.99

M i ti k VIC = 0 IO = 500 µA25°C –4.85 –4.91 –4.85 –4.91



out ut voltage

VIC = 0 IO = 5 A25°C –3.5 –4.1 –3.5 –4.1


L i l diff ti l RL = 10 kΩ25°C 20 50 20 50


VO = ±4 VRL = 10 kΩ


RL = 1 MΩ 25°C 300 300


riCommon-mode input resistance

25°C 1012 1012 Ω




f = 1 MHz, AV = 10 25°C 130 130 Ω

CMRRCommon-mode rejection VIC = –5 V to 2.7 V 25°C 75 80 75 80

dBCMRRj

ratioIC

VO = 0, RS = 50 Ω Full range 75 75dB

kSVRSupply-voltage rejection VDD± = ± 2.2 V to ±8 V, 25°C 80 95 80 95

dBkSVRy g j

ratio (∆VDD± /∆VIO)DD± ,


† Full range is –40°C to 125°C for Q level part, –55°C to 125°C for M level part.NOTE 4: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA = 150°C extrapolated





TLC2274Q and TLC2274M electrical characteristics at specified free-air temperature, V DD± = ±5 V(unless otherwise noted) (continued)






mA


TLC2274Q and TLC2274M operating characteristics at specified free-air temperature, VDD± = ±5 V






VO = ±2.3 V,CL = 100 pF

RL = 10 kΩ,Full

1 7 1 7V/µsgain CL = 100 F

range1.7 1.7


nV/√HzVnq


VN(PP)





25°C 0.6 0.6 fA /√Hz



VO = ±2.3 V,RL = 10 kΩ, AV = 10 25°C 0.004% 0.004%

noise f = 20 kHz AV = 100 0.03% 0.03%


product,

CL = 100 pFL ,

25°C 2.25 2.25 MHz

BOM

Maximumoutput swing


bandwidth

O(PP) ,RL = 10 kΩ,

V ,CL = 100 pF

25°C 0.54 0.54 MHz

AV = –1, To 0 1% 1 5 1 5

t Settling time

AV = 1,Step = –2.3 V to 2.3 V,

To 0.1%25°C


RL = 10 kΩ,To 0 01%

25°C3 2 3 2

µsL

CL = 100 pF To 0.01% 3.2 3.2

φmPhase margin atunit gain RL = 10 kΩ, CL = 100 pF

25°C 52° 52°

Gain marginL L

25°C 10 10 dB






TYPICAL CHARACTERISTICS

Table of GraphsFIGURE

VIO Input offset voltageDistribution 1 – 4

VIO Input offset voltagevs Common-mode voltage 5, 6

αVIO Input offset voltage temperature coefficient Distribution 7 – 10

IIB /IIO Input bias and input offset current vs Free-air temperature 11

VI Input voltage rangevs Supply voltage 12

VI Input voltage rangey g

vs Free-air temperature 13

VOH High-level output voltage vs High-level output current 14

VOL Low-level output voltage vs Low-level output current 15, 16

VOM+ Maximum positive peak output voltage vs Output current 17

VOM– Maximum negative peak output voltage vs Output current 18

VO(PP) Maximum peak-to-peak output voltage vs Frequency 19

IOS Short circuit output currentvs Supply voltage 20

IOS Short-circuit output currenty g


VO Output voltage vs Differential input voltage 22, 23

vs Load resistance 24AVD Large-signal differential voltage amplification

vs Load resistancevs Frequency

2425, 26VD g g g q y

vs Free-air temperature 27, 28

zo Output impedance vs Frequency 29, 30

CMRR Common mode rejection ratiovs Frequency 31

CMRR Common-mode rejection ratioq y


kSVR Supply voltage rejection ratiovs Frequency 33, 34

kSVR Supply-voltage rejection ratioq y

vs Free-air temperature,

35

IDD Supply currentvs Supply voltage 36, 37

IDD Supply currenty g

vs Free-air temperature,

38, 39

SR Slew ratevs Load capacitance 40

SR Slew ratevs Free-air temperature 41

Inverting large-signal pulse response 42, 43

VOVoltage-follower large-signal pulse response 44, 45

VOInverting small-signal pulse response 46, 47

Voltage-follower small-signal pulse response 48, 49

Vn Equivalent input noise voltage vs Frequency 50, 51

Noise voltage (referred to input) Over a 10-second period 52

Integrated noise voltage vs Frequency 53

THD + N Total harmonic distortion plus noise vs Frequency 54

Gain bandwidth productvs Supply voltage 55

Gain-bandwidth producty g


φ Phase marginvs Load capacitance 57φm Phase marginvs Frequency 25, 26

Gain margin vs Load capacitance 58

NOTE: For all graphs where VDD = 5 V, all loads are referenced to 2.5 V.





VIO – Input Offset Voltage – mV

Per

cent

age

of A

mpl

ifier

s –

%

DISTRIBUTION OF TLC2272INPUT OFFSET VOLTAGE

10

5

0

20

15

–1.6 –1.2 0 0.4 0.8 1.2 1.6

891 Amplifiers From

–0.8 –0.4

2 Wafer LotsVDD = ±2.5 V

TA = 25°C

Figure 1


Per

cent

age

of A

mpl

ifier

s –

%


10

5

0

20

15

–1.6 –1.2 0 0.4 0.8 1.2 1.6–0.8 –0.4

891 Amplifiers From2 Wafer LotsVDD = ±5 VTA = 25°C

Figure 2

Figure 3


Per

cent

age

of A

mpl

ifier

s –

%


10

5

0

20

15

0 0.4 0.8 1.2 1.6

992 Amplifiers From

–1.6 –1.2 –0.8 –0.4

2 Wafer LotsVDD = ±2.5 V

Figure 4


Per

cent

age

of A

mpl

ifier

s –

%


10

5

0

20

15

0 0.4 0.8 1.2 1.6

992 Amplifiers From

–1.6 –1.2 –0.8 –0.4

2 Wafer LotsVDD = ±5 V






0.5

0

–1–1 0 1

VIO

– In

put O

ffset

Vol

tage

– m

V

1

2 3 4 5

VIO

VIC – Common-Mode Voltage – V

VDD = 5 VTA = 25°CRS = 50 Ω

–0.5

INPUT OFFSET VOLTAGEvs

COMMON-MODE VOLTAGE

Figure 5

0.5

0

–1–1 0 1

VIO

– In

put O

ffset

Vol

tage

– m

V

1

2 3 4 5

INPUT OFFSET VOLTAGEvs

COMMON-MODE VOLTAGE

VIC – Common-Mode Voltage – V

VIO –0.5

VDD = ±5 VTA = 25°CRS = 50 Ω

–6 –5 –4 –3 –2

Figure 6

15

10

5

0–1 0 1

Per

cent

age

of A

mpl

ifier

s –

%

20

25

2 3 4 5

DISTRIBUTION OF TLC2272 INPUT OFFSETVOLTAGE TEMPERATURE COEFFICIENT †

αVIO – Temperature Coefficient – µV/°C

128 Amplifiers From2 Wafer LotsVDD = ±2.5 VP Package25°C to 125°C

–5 –4 –3 –2

Figure 7

–5 –4 –3 –2

15

10

5

0–1 0 1

Per

cent

age

of A

mpl

ifier

s –

%

20

25

2 3 4 5



128 Amplifiers From2 Wafer LotsVDD = ±5 VP Package25°C to 125°C

Figure 8

† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.





15

10

5

00 1

Per

cent

age

of A

mpl

ifier

s –

%

20

25

2 3 4 5



–5 –4 –3 –2 –1

128 Amplifiers From2 Wafer LotsVDD = ±2.5 VN PackageTA = 25°C to 125°C

Figure 9

15

10

5

0

Per

cent

age

of A

mpl

ifier

s –

%

20

25



0 1 2 3 4 5–5 –4 –3 –2 –1

128 Amplifiers From2 Wafer LotsVDD = ±2.5 VN PackageTA = 25°C to 125°C

Figure 10

15

10

5

025 45 65 85

20

25

30

105 125

INPUT BIAS AND INPUT OFFSET CURRENT †

vsFREE-AIR TEMPERATURE

TA – Free-Air Temperature – °C

35VDD = ±2.5 VVIC = 0VO = 0RS = 50 Ω

IIB

IIO

IIB a

nd II

O –

Inpu

t Bia

s an

d In

put O

ffset

Cur

rent

s –

pAIBI

I IO

Figure 11

0

– 2

– 6

– 8

– 10

8

– 4

2 3 4 5 6 7 8

VI –

Inpu

t Vol

tage

Ran

ge –

V

4

2

6

10

INPUT VOLTAGE RANGEvs

SUPPLY VOLTAGE


VI

TA = 25°C RS = 50 Ω

|VIO| ≤ 5mV

12

Figure 12







–75 – 25 0 25 50 75 100 125

2

1

0

–1

3

4

5

VI –

Inpu

t Vol

tage

Ran

ge –

VV

I

INPUT VOLTAGE RANGE †



|VIO| ≤ 5mV

VDD = 5 V

– 50

Figure 13

V0H

– H

igh-

Leve

l Out

put V

olta

ge –

VV

OH

IOH – High-Level Output Current – mA

4

2

1

0

6

3

0 1 2 3 4

5

HIGH-LEVEL OUTPUT VOLTAGE †

vsHIGH-LEVEL OUTPUT CURRENT

VDD = 5 V

TA = 125°C

TA = –55°C

TA = 25°C

Figure 14

VO

L –

Low

-Lev

el O

utpu

t Vol

tage

– V

0.6

0.4

0.2

00 1 2 3

0.8

4 5

VDD = 5 VTA = 25°C

IOL – Low-Level Output Current – mA

VO

L

VIC = 0

VIC = 1.25 V

LOW-LEVEL OUTPUT VOLTAGEvs

LOW-LEVEL OUTPUT CURRENT

1

1.2

VIC = 2.5 V

Figure 15

LOW-LEVEL OUTPUT VOLTAGE †

vsLOW-LEVEL OUTPUT CURRENT

VO

L –

Low

-Lev

el O

utpu

t Vol

tage

– V

IOL – Low-Level Output Current – mA

VO

L

0.6

0.4

0.2

00 1 2 3

0.8

4

1

1.2

5 6

1.4VDD = 5 V VIC = 2.5 V

TA = 125°C

TA = 25°C

TA = –55°C

Figure 16






3

2

10 1 2 3 4 5

– M

axim

um P

ositi

ve P

eak

Out

put V

olta

ge –

V

4

5

MAXIMUM POSITIVE PEAK OUTPUT VOLTAGE †

vsOUTPUT CURRENT

|IO| – Output Current – mA

TA = –55°C

TA = 25°C

TA = 125°C

VDD± = ±5 V

VO

M +

Figure 17

0 1 2 3 4 5 6

IO – Output Current – mA

MAXIMUM NEGATIVE PEAK OUTPUT VOLTAGE †

vsOUTPUT CURRENT

VDD = ±5 VVIC = 0

TA = 125°C

TA = 25°C

TA = –55°C

–3.8

–4

–4.2

–4.4

–4.6

–4.8

–5

– M

axim

um N

egat

ive

Pea

k O

utpu

t Vol

tage

– V

VO

M –

Figure 18

Figure 19

2

1

010 k 100 k 1 M

3

f – Frequency – Hz

4

10 M

6

5

7

8

9

10

MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGEvs

FREQUENCY

V(O

PP

) –

Max

imum

Pea

k-to

-Pea

k O

utpu

t Vol

tage

– V

VO

(PP

)

VDD = 5 V

VDD = ±5 V

RL = 10 kΩTA = 25°C

Figure 20

4

0

2 3 4

8

12

16

5 6 7 8

IOS

– S

hort

-Circ

uit O

utpu

t Cur

rent

– m

AO

SI


SHORT-CIRCUIT OUTPUT CURRENTvs

SUPPLY VOLTAGE

VID = 100 mV

VO = 0TA = 25°C

–8

VID = –100 mV

–4







–5

SHORT-CIRCUIT OUTPUT CURRENT†


–75 –50 –25 0 25 50 75 100 125

–1

–3

7

11

15

IOS

– S

hort

-Circ

uit O

utpu

t Cur

rent

– m

AO

SI


VID = 100 mV

VID = –100 mV

VO = 0VDD = ±5 V

Figure 21

OUTPUT VOLTAGEvs

DIFFERENTIAL INPUT VOLTAGE

3

2

1

0800

4

5

1200

VID – Differential Input Voltage – µV

– O

utpu

t Vol

tage

– V

VO

–800 –400 4000

VDD = 5 VTA = 25°CRL = 10 kΩVIC = 2.5 V

Figure 22

1

–1

–3

–50 250

3

5

OUTPUT VOLTAGEvs

DIFFERENTIAL INPUT VOLTAGE

500 750 1000VID – Differential Input Voltage – µV

– O

utpu

t Vol

tage

– V

VO

–1000 –750 –250–500

VDD = ±5 VTA = 25°CRL = 10 kΩVIC = 0

Figure 23

0.1

1

0.1 1 10 100

10

100

1000

LARGE-SIGNAL DIFFERENTIALVOLTAGE AMPLIFICATION

vsLOAD RESISTANCE

AV

D –

Diff

eren

tial V

olta

ge A

mpl

ifica

tion

– V

/mV

VD

A

RL – Load Resistance – k Ω

VO = ±1 VTA = 25°C

VDD = ±5 V

VDD = 5 V

Figure 24






0

20

1 k 10 k 100 k 1 M

40

60

80

LARGE-SIGNAL DIFFERENTIAL VOLTAGEAMPLIFICATION AND PHASE MARGIN

vsFREQUENCY


10 M

om –

Pha

se M

argi

n φ m

VDD = 5 VRL = 10 kΩCL = 100 pFTA = 25°C

–20

–40 –90°

–45°

0°

45°

90°

135°

180°A

VD

– L

arge

-Sig

nal D

iffer

entia

l

ÁÁÁÁÁÁ

AV

D Vol

tage

Am

plifi

catio

n –

dB

Figure 25

0

20

1 k 10 k 100 k 1 M

40

60

80

LARGE-SIGNAL DIFFERENTIAL VOLTAGEAMPLIFICATION AND PHASE MARGIN

vsFREQUENCY

f – Frequency – Hz10 M

VDD = ±5 VRL = 10 kΩCL = 100 pFTA = 25°C

om –

Pha

se M

argi

n φ m

–20

–40 –90°

–45°

0°

45°

90°

135°

180°

AV

D –

Lar

ge-S

igna

l Diff

eren

tial

ÁÁÁÁÁÁ

AV

D Vol

tage

Am

plifi

catio

n –

dB

Figure 26






LARGE-SIGNAL DIFFERENTIALVOLTAGE AMPLIFICATION †


–75 –50 –25 0 25 50 75 100 12510

100

1 k


VDD = 5 V VIC = 2.5 VVO = 1 to 4 V

RL = 1 MΩ

RL = 10 kΩ

AV

D –

Lar

ge-S

igna

l Diff

eren

tial

ÁÁÁÁ

AV

DV

olta

ge A

mpl

ifica

tion

– V

/mV

Figure 27

LARGE-SIGNAL DIFFERENTIALVOLTAGE AMPLIFICATION †


–75 –50 –25 0 25 50 75 100 12510

100

1 k


RL = 1 MΩ

RL = 10 kΩ

VDD = ±5 VVIC = 0VO = ± 4 V

AV

D –

Lar

ge-S

igna

l Diff

eren

tial

ÁÁÁÁ

AV

DV

olta

ge A

mpl

ifica

tion

– V

/mV

Figure 28

10

1

0.1

1000

100

100 1 k 10 k 100 k 1 M

zo –

Out

put I

mpe

danc

e –

O


Ωz o

OUTPUT IMPEDANCEvs

FREQUENCY

VDD = 5 VTA = 25°C

AV = 100

AV = 10

AV = 1

Figure 29

10

1

0.1

1000

100

100 1 k 10 k 100 k 1 M

zo –

Out

put I

mpe

danc

e –

O


Ωz o

OUTPUT IMPEDANCEvs

FREQUENCY

VDD = ±5 VTA = 25°C

AV = 100

AV = 10

AV = 1

Figure 30






COMMON-MODE REJECTION RATIOvs

FREQUENCY

60

40

20

010 100 1 k 10 k

CM

RR

– C

omm

on-M

ode

Rej

ectio

n R

atio

– d

B

80

100

100 k 1 M


VDD = ±5 V

VDD = 5 V

10 M

TA = 25°C

Figure 31


CM

RR

– C

omm

on-M

ode

Rej

ectio

n R

atio

– d

B

COMMON-MODE REJECTION RATIOvs

FREE-AIR TEMPERATURE

82

78

74

70

86

90

–75 –50 –25 0 25 50 75 100 125

VDD = ±5 V

VDD = 5 V

VIC = 0 to 2.7 V

VIC = –5 V to 2.7 V

Figure 32

40

20

0

10 100 1 k

kSV

R –

Sup

ply-

Vol

tage

Rej

ectio

n R

atio

– d

B

60

80


100

10 k 100 k 1 M 10 M

SUPPLY-VOLTAGE REJECTION RATIOvs

FREQUENCY

kS

VR

VDD = 5 VTA = 25°C

kSVR+

kSVR–

–20

Figure 33

40

20

0

10 100 1 k

kSV

R –

Sup

ply-

Vol

tage

Rej

ectio

n R

atio

– d

B

60

80


100

10 k 100 k 1 M 10 M

SUPPLY-VOLTAGE REJECTION RATIOvs

FREQUENCY

kS

VR

VDD = ±5 VTA = 25°C

kSVR+

kSVR–

–20

Figure 34





TYPICAL CHARACTERISTICSkS

VR

– S

uppl

y V

olta

ge R

ejec

tion

Rat

io –

dB

SUPPLY VOLTAGE REJECTION RATIO †


kS

VR

TA – Free-Air Temperature – °C–75 –50 –25 0 25 50 75 100 125

100

95

90

85

105

110VDD± = ±2.2 V to ±8 VVO = 0

Figure 35

0 1 2 3 4 5 6 7 80

0.6

1.2

1.8

2.4

3

IDD

– S

uppl

y C

urre

nt –

mA

DD

I

|VDD± | – Supply Voltage – V

VO = 0No Load

TA = 25°C

TA = –55°C

TA = 125°C

Figure 36

TLC2272SUPPLY CURRENT†

vsSUPPLY VOLTAGE

Figure 37

0 1 2 3 4 5 6 7 80

1.2

2.4

3.6

4.8

6

IDD

– S

uppl

y C

urre

nt –

mA

DD

I

|VDD± | – Supply Voltage – V

VO = 0No Load

TA = 25°C

TA = –55°C

TA = 125°C


vsSUPPLY VOLTAGE

Figure 38

–75 –50 –25 0 25 50 75 100 1250

0.6

1.2

1.8

2.4

3


IDD

– S

uppl

y C

urre

nt –

mA

DD

I

VDD = 5 VVO = 2.5 V

VDD = ±5 VVO = 0








Figure 39

–75 –50 –25 0 25 50 75 100 1250

1.2

2.4

3.6

4.8

6


IDD

– S

uppl

y C

urre

nt –

mA

DD

I

VDD = 5 VVO = 2.5 V

VDD = ±5 VVO = 0



µs

SR

– S

lew

Rat

e –

V/

0

1

2

3

CL – Load Capacitance – pF

SLEW RATEvs

LOAD CAPACITANCE

10 k1 k10010

SR +

SR –

4

5VDD = 5 VAV = –1TA = 25°C

Figure 40

3

2

1

4

µsS

R –

Sle

w R

ate

– V

/

–75 –50 –25 0 25 50 75 100 125


SLEW RATE†


VDD = 5 VRL = 10 kΩCL = 100 pFAV = 1

SR +

SR –

0

5

Figure 41

INVERTING LARGE-SIGNAL PULSE RESPONSE

2

1

01 2 3 4 5

3

4

5

6 7 8 9

VO

– O

utpu

t Vol

tage

– m

VV

O

t – Time – µs

VDD = 5 VRL = 10 kΩCL = 100 pFTA = 25°CAV = –1

0

Figure 42







0

– 1

– 3

– 4

– 5

4

– 2

1 2 3 4 5

2

1

3

5

6 7 8 9

VO

– O

utpu

t Vol

tage

– V

VO

t – Time – µs

VDD = ±5 VRL = 10 kΩCL = 100 pFTA = 25°CAV = –1

INVERTING LARGE-SIGNAL PULSE RESPONSE

0

Figure 43

3

2

1

01 2 3 4 5

4

5

6 7 8 9V

O –

Out

put V

olta

ge –

VV

Ot – Time – µs

VDD = 5 VRL = 10 kΩCL = 100 pFAV = 1TA = 25°C

VOLTAGE-FOLLOWERLARGE-SIGNAL PULSE RESPONSE

0

Figure 44

VOLTAGE-FOLLOWERLARGE-SIGNAL PULSE RESPONSE

0

–1

4

1 2 3 4 5

2

1

3

5

6 7 8 9

VO

– O

utpu

t Vol

tage

– V

VO

t – Time – µs

VDD = ±5 VRL = 10 kΩCL = 100 pFTA = 25°CAV = 1

0

–2

–3

–5

–4

Figure 45

INVERTING SMALL-SIGNAL PULSE RESPONSE

2.5

2.45

2.40.5 1 1.5 2 2.5

2.55

2.6

2.65

3.5 4.5 5 5.5

VO

– O

utpu

t Vol

tage

– V

VO

t – Time – µs

VDD = 5 VRL = 10 kΩCL = 100 pFTA = 25°CAV = –1

0 3 4

Figure 46





0

–1000 0.5 1 1.5 2

50

100

2.5 3 3.5 4

VO

– O

utpu

t Vol

tage

– m

VV

O

t – Time – µs

INVERTING SMALL-SIGNAL PULSE RESPONSE


–50

Figure 47

VOLTAGE-FOLLOWERSMALL-SIGNAL PULSE RESPONSE

2.5

2.45

2.4

2.55

2.6

0 0.5 1 1.5

VO

– O

utpu

t Vol

tage

– V

VO

t – Time – µs

2.65VDD = 5 VRL = 10 kΩCL = 100 pFTA = 25°CAV = 1

Figure 48

VOLTAGE-FOLLOWERSMALL-SIGNAL PULSE RESPONSE

0

–50

–100

50

100

0 0.5 1 1.5

VO

– O

utpu

t Vol

tage

– m

VV

O

t – Time – µs


Figure 49

20

10

010 100 1 k

Vn

– E

quiv

alen

t Inp

ut N

oise

Vol

tage

– n

V H

z

30


40

10 k

EQUIVALENT INPUT NOISE VOLTAGEvs

FREQUENCY

50

60

Vn

nV/

Hz VDD = 5 V

TA = 25°CRS = 20 Ω

Figure 50






20

10

010 100 1 k

Vn

– E

quiv

alen

t Inp

ut N

oise

Vol

tage

– n

V H

z

30


40

10 k

EQUIVALENT INPUT NOISE VOLTAGEvs

FREQUENCY

50

60

Vn

nV/

Hz

VDD = ±5 VTA = 25°CRS = 20 Ω

Figure 51

–750

–10002 4 6

0

250

8 10N

oise

Vol

tage

– n

V

t – Time – s

NOISE VOLTAGEOVER A 10 SECOND PERIOD

0

VDD = 5 Vf = 0.1 to 10 HzTA = 25°C

500

750

1000

–250

–500

Figure 52

Inte

grat

ed N

oise

Vol

tage

– u

VR

MS

1

0.1

100

1 10 100 1 k


INTEGRATED NOISE VOLTAGEvs

FREQUENCY

10 k 100 k

VR

MS

µ

Calculated UsingIdeal Pass-Band FilterLower Frequency = 1 HzTA= 25°C

10

Figure 53

0.0001

0.001

100 1 k 10 k 100 k

TH

D +

N –

Tot

al H

arm

onic

Dis

tort

ion

Plu

s N

oise

– %


TOTAL HARMONIC DISTORTION PLUS NOISEvs

FREQUENCY

0.01

0.1

1VDD = 5 VTA = 25°CRL = 10 kΩ

AV = 100

AV = 10

AV = 1

Figure 54





Figure 55

Gai

n-B

andw

idth

Pro

duct

– M

Hz

2.1

20 1 2 3 4 5

2.2

2.3

6 7 8|VDD±| – Supply Voltage – V

2.4

2.5

GAIN-BANDWIDTH PRODUCTvs

SUPPLY VOLTAGE

f = 10 kHzRL = 10 kΩCL = 100 pFTA = 25°C

Figure 56

–75 –50 –25 0 25 50 75 100 125TA – Free-Air Temperature – °C

Gai

n-B

andw

idth

Pro

duct

– M

Hz

GAIN-BANDWIDTH PRODUCT †


1.8

1.6

1.4

2

2.4

2.2

2.6

2.8

3VDD = 5 Vf = 10 kHzRL = 10 kΩCL = 100 pF

10

om –

Pha

se M

argi

n

10000CL – Load Capacitance – pF

φm

PHASE MARGINvs

LOAD CAPACITANCE

1000100

VDD = ±5 VTA = 25°C

Rnull = 20 Ω

Rnull = 10 Ω

Rnull = 0

75°

60°

45°

30°

15°

0°

10 kΩ

10 kΩ

VDD –

VDD +Rnull

CLVI

Rnull = 100 Ω

Rnull = 50 Ω

Figure 57 Figure 58

3

010

Gai

n M

argi

n –

dB

6

9

10000CL – Load Capacitance – pF

12

15

GAIN MARGINvs

LOAD CAPACITANCE

1000100

VDD = 5 VAV = 1RL = 10 kΩTA = 25°C






APPLICATION INFORMATION

macromodel information

Macromodel information provided was derived using Microsim Parts , the model generation software usedwith Microsim PSpice . The Boyle macromodel (see Note 5) and subcircuit in Figure 59 were generated usingthe TLC227x typical electrical and operating characteristics at TA = 25°C. Using this information, outputsimulations of the following key parameters can be generated to a tolerance of 20% (in most cases):

Maximum positive output voltage swing Maximum negative output voltage swing Slew rate Quiescent power dissipation Input bias current Open-loop voltage amplification

Unity gain frequency Common-mode rejection ratio Phase margin DC output resistance AC output resistance Short-circuit output current limit

NOTE 5: G. R. Boyle, B. M. Cohn, D. O. Pederson, and J. E. Solomon, “Macromodeling of Intergrated Circuit Operational Amplifiers”, IEEE Journalof Solid-State Circuits, SC-9, 353 (1974).

OUT

+

–

+

–

+

–

+

–

+–

+

–

+

– +

–

+–

.SUBCKT TLC227x 1 2 3 4 5C1 11 1214E–12C2 6 760.00E–12DC 5 53DXDE 54 5DXDLP 90 91DXDLN 92 90DXDP 4 3DXEGND 99 0POLY (2) (3,0) (4,) 0 .5 .5FB 99 0POLY (5) VB VC VE VLP VLN 0+ 984.9E3 –1E6 1E6 1E6 –1E6GA 6 011 12 377.0E–6GCM 0 6 10 99 134E–9ISS 3 10DC 216.OE–6HLIM 90 0VLIM 1KJ1 11 210 JXJ2 12 110 JXR2 6 9100.OE3

RD1 60 112.653E3RD2 60 122.653E3R01 8 550R02 7 9950RP 3 44.310E3RSS 10 99925.9E3VAD 60 4–.5VB 9 0DC 0VC 3 53 DC .78VE 54 4DC .78VLIM 7 8DC 0VLP 91 0DC 1.9VLN 0 92DC 9.4.MODEL DX D (IS=800.0E–18).MODEL JX PJF (IS=1.500E–12BETA=1.316E-3+ VTO=–.270).ENDS

VCC+

RP

IN –2

IN+1

VCC–

VAD

RD1

11

J1 J2

10

RSS ISS

3

12

RD2

60

VE

54DE

DP

VC

DC

4

C1

53

R2

6

9

EGND

VB

FB

C2

GCM GA VLIM

8

5

RO1

RO2

HLIM

90

DIP

91

DIN

92

VINVIP

99

7

Figure 59. Boyle Macromodel and Subcircuit

PSpice and Parts are trademarks of MicroSim Corporation.

Macromodels, simulation models, or other models provided by TI,directly or indirectly, are not warranted by TI as fully representing allof the specification and operating characteristics of thesemiconductor product to which the model relates.




MECHANICAL DATAD (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE14 PIN SHOWN

4040047/D 10/96

0.228 (5,80)0.244 (6,20)

0.069 (1,75) MAX0.010 (0,25)0.004 (0,10)

1

14

0.014 (0,35)0.020 (0,51)

A

0.157 (4,00)0.150 (3,81)

7

8

0.044 (1,12)0.016 (0,40)

Seating Plane

0.010 (0,25)

PINS **

0.008 (0,20) NOM

A MIN

A MAX

DIM

Gage Plane

0.189(4,80)

(5,00)0.197

8

(8,55)

(8,75)

0.337

14

0.344

(9,80)

16

0.394(10,00)

0.386

0.004 (0,10)

M0.010 (0,25)

0.050 (1,27)

0°–8°

NOTES: A. All linear dimensions are in inches (millimeters).B. This drawing is subject to change without notice.C. Body dimensions do not include mold flash or protrusion, not to exceed 0.006 (0,15).D. Falls within JEDEC MS-012





MECHANICAL DATAFK (S-CQCC-N**) LEADLESS CERAMIC CHIP CARRIER

4040140/D 10/96

28 TERMINAL SHOWN

B

0.358(9,09)

MAX

(11,63)

0.560(14,22)

0.560

0.458

0.858(21,8)

1.063(27,0)

(14,22)

ANO. OF

MINMAX

0.358

0.660

0.761

0.458

0.342(8,69)

MIN

(11,23)

(16,26)0.640

0.739

0.442

(9,09)

(11,63)

(16,76)

0.962

1.165

(23,83)0.938

(28,99)1.141

(24,43)

(29,59)

(19,32)(18,78)

**

20

28

52

44

68

84

0.020 (0,51)

TERMINALS

0.080 (2,03)0.064 (1,63)

(7,80)0.307

(10,31)0.406

(12,58)0.495

(12,58)0.495

(21,6)0.850

(26,6)1.047

0.045 (1,14)

0.045 (1,14)0.035 (0,89)

0.035 (0,89)

0.010 (0,25)

121314151618 17

11

10

8

9

7

5

432

0.020 (0,51)0.010 (0,25)

6

12826 27

19

21B SQ

A SQ22

23

24

25

20

0.055 (1,40)0.045 (1,14)

0.028 (0,71)0.022 (0,54)

0.050 (1,27)

NOTES: A. All linear dimensions are in inches (millimeters).B. This drawing is subject to change without notice.C. This package can be hermetically sealed with a metal lid.D. The terminals are gold plated.E. Falls within JEDEC MS-004




MECHANICAL DATAJ (R-GDIP-T**) CERAMIC DUAL-IN-LINE PACKAGE

1

20

0.290

(7,87)0.310

0.975(24,77)

(23,62)0.930

(7,37)

0.245(6,22)

(7,62)0.300

181614PINS **

0.290

(7,87)0.310

0.785(19,94)

(19,18)0.755

(7,37)

0.310(7,87)

(7,37)0.290

0.755(19,18)

(19,94)0.785

0.245(6,22)

(7,62)0.300

A

0.300(7,62)

(6,22)0.245

A MIN

A MAX

B MAX

B MIN

C MIN

C MAX

DIM

0.310(7,87)

(7,37)0.290

(23,10)0.910

0.300(7,62)

(6,22)0.245

0°–15°

Seating Plane

0.014 (0,36)0.008 (0,20)

4040083/D 08/98

C

8

7

0.020 (0,51) MIN

B

0.070 (1,78)0.100 (2,54)

0.065 (1,65)0.045 (1,14)

14 PIN SHOWN

14

0.015 (0,38)0.023 (0,58)

0.100 (2,54)

0.200 (5,08) MAX

0.130 (3,30) MIN

NOTES: A. All linear dimensions are in inches (millimeters).B. This drawing is subject to change without notice.C. This package can be hermetically sealed with a ceramic lid using glass frit.D. Index point is provided on cap for terminal identification only on press ceramic glass frit seal only.E. Falls within MIL STD 1835 GDIP1-T14, GDIP1-T16, GDIP1-T18, GDIP1-T20, and GDIP1-T22.





MECHANICAL DATAN (R-PDIP-T**) PLASTIC DUAL-IN-LINE PACKAGE

20

0.975(24,77)

0.940(23,88)

18

0.920

0.850

14

0.775

0.745

(19,69)

(18,92)

16

0.775(19,69)

(18,92)0.745

A MIN

DIM

A MAX

PINS **

0.310 (7,87)0.290 (7,37)

(23.37)

(21.59)

Seating Plane

0.010 (0,25) NOM

14/18 PIN ONLY

4040049/C 08/95

9

8

0.070 (1,78) MAX

A

0.035 (0,89) MAX 0.020 (0,51) MIN

16

1

0.015 (0,38)0.021 (0,53)

0.200 (5,08) MAX

0.125 (3,18) MIN

0.240 (6,10)0.260 (6,60)

M0.010 (0,25)

0.100 (2,54)0°–15°

16 PIN SHOWN

NOTES: A. All linear dimensions are in inches (millimeters).B. This drawing is subject to change without notice.C. Falls within JEDEC MS-001 (20 pin package is shorter then MS-001.)




MECHANICAL DATAP (R-PDIP-T8) PLASTIC DUAL-IN-LINE PACKAGE

4040082/B 03/95

0.310 (7,87)0.290 (7,37)

0.010 (0,25) NOM

0.400 (10,60)0.355 (9,02)

58

41

0.020 (0,51) MIN

0.070 (1,78) MAX

0.240 (6,10)0.260 (6,60)

0.200 (5,08) MAX

0.125 (3,18) MIN

0.015 (0,38)0.021 (0,53)

Seating Plane

M0.010 (0,25)

0.100 (2,54) 0°–15°

NOTES: A. All linear dimensions are in inches (millimeters).B. This drawing is subject to change without notice.C. Falls within JEDEC MS-001





MECHANICAL DATAPW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE

4040064/E 08/96

14 PIN SHOWN

Seating Plane

1,20 MAX

1

A

7

14

0,19

4,504,30

8

6,206,60

0,30

0,750,50

0,25

Gage Plane

0,15 NOM

0,65 M0,10

0°–8°

0,10

PINS **

A MIN

A MAX

DIM

2,90

3,10

8

4,90

5,10

14

6,60

6,404,90

5,10

16

7,70

20

7,90

24

9,60

9,80

28

0,150,05

NOTES: A. All linear dimensions are in millimeters.B. This drawing is subject to change without notice.C. Body dimensions do not include mold flash or protrusion not to exceed 0,15.D. Falls within JEDEC MO-153

IMPORTANT NOTICE

Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinueany product or service without notice, and advise customers to obtain the latest version of relevant informationto verify, before placing orders, that information being relied on is current and complete. All products are soldsubject to the terms and conditions of sale supplied at the time of order acknowledgement, including thosepertaining to warranty, patent infringement, and limitation of liability.

TI warrants performance of its semiconductor products to the specifications applicable at the time of sale inaccordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extentTI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarilyperformed, except those mandated by government requirements.

CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OFDEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICALAPPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, ORWARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHERCRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TOBE FULLY AT THE CUSTOMER’S RISK.

In order to minimize risks associated with the customer’s applications, adequate design and operatingsafeguards must be provided by the customer to minimize inherent or procedural hazards.

TI assumes no liability for applications assistance or customer product design. TI does not warrant or representthat any license, either express or implied, is granted under any patent right, copyright, mask work right, or otherintellectual property right of TI covering or relating to any combination, machine, or process in which suchsemiconductor products or services might be or are used. TI’s publication of information regarding any thirdparty’s products or services does not constitute TI’s approval, warranty or endorsement thereof.

Copyright 1999, Texas Instruments Incorporated

Documents

TLC227x, TLC227xA Advanced LinCMOS RAIL-TO-RAIL ...nic.vajn.icu/PDF/TexasInstruments/TLC2272.pdf · The TLC2272/4 also makes great upgrades to the TLC272/4 or TS272/4 in standard