ST36-140 Radial Telescopic Stacker...ST36-140 Radial Telescopic Stacker Component Specification Belt Scraper Carbite tungsten tipped finger scraper to suit 900mm belt. Belt cleaners

ST36-140 Radial Telescopic Stacker

Machine Length:

Machine Weight:

Tonnes Per Hour:

Max Lump Size:

In-Feed Height:

Towing Height:

26.5m (42m extended)

38 Tonnes

800tph @ density = 1.6T/m3

100mm

3.9m

4.11m

Technical Specification

24 Gortnaglough RoadDungannonCo. TyroneNorthern IrelandBT71 5EE

Addresss

T: +44(0) 28 8773 9147E: [email protected]

Dealer Information

Matpro Machinery Ltd, Brookhouse Farm, Allostock, Knutsford, Cheshire, WA16 9LU

www.matpro.co.uk [email protected] 01565 723886



Addresss


Performance

The Radial Telescopic Stacker operates in the following way when used in manual mode. A series of switches located on the operating control panel allow you to move the conveyor manually to your desired location using the left/right, up/down and in/out functions.

It operates in the following way when used in automatic mode. The machine will start fully retracted pre-set on its left hand parameter at 0 degrees. It will then proceed on a right hand radial arc until reaching the right hand parameter as pre-set by the operator. This can be set at any angle between 0 and 270 degrees.

The machine will automatically telescope out 1 meter and start on its left hand radial arc. This process will continue until the machine extends fully up to maximum of 16 meters extension. When fully extended, the machine will raise when material is detected 1 meter from the head drum pile high material sensor. The conveyor will continue on its left to right cycles until it reaches its fully retracted position. The process will repeat continuously until machine reaches final height of 14 meters (16 degrees). On the last run, the final rows indicator light will flash on panel.


Structural Specification

Main outer lattice frame is constructed from 100x100x10mm (top) and 200x100x10mm (bottom) heavy structural angles. The extendible inner lattice frame is constructed using 100x50x6mm rectangular hollow section.

The forward support frame (Undercarriage) is constructed of 200x100x6mm rectangular hollow section. The forward support frame is hydraulically raised and lowered for transportation purposes.

King pin counterweight and side plate assemblies are designed to allow ample turning clearance for most 5th wheel tractors. Safety guards at all pinch points are standard.

Standard accessories include loading hopper (stone box) 1500mm wide x 2100mm long x 400mm high, fabricated from 6mm plate with rubber skirting.

The conveyor mid section is hydraulically raised to allow the wheels to swing from travel mode to radial position. Wide wheelbase in radial position offers great stability during operation while the closed travel position allows for safe highway transportation

Telescopic action is activated by a 219mm-dia drum (1.1 KW motor) and ½” (12.7mm) cable winch package, which moves the conveyor, approximately 0.05 m/s (2764Nm, 2.4 Tonnes pull).

Radial Arms are activated by an electric drives motor. The travelling speed required is 0.1m/s. The radial arms move up and down powered by hydraulic rams.


Addresss


Dealer Information




Component Specification

BeltsOuter conveyor: EP500 / 3ply, 5mm top 1.5mm bottom cover.

Inner conveyor: EP500 / 3ply, 5mm top 1.5mm bottom cover.Standard belting covers are 5mm x 1.5mm 3ply EP500 with vulcanised splice or clipped belt for container transportation.

Outer conveyor Speed: 1.9m/s

Inner conveyor Speed: 2.4m/s

RollersTroughing Rollers: Ø 127mm troughing at 3 roll set for 900mm belt.

Return Rollers: Spiral rollers Ø 102mm for 900mm belt.Both the main conveyor and the telescopic conveyor utilise Ø 5” (Ø 127mm) steel idlers with 35-degree troughs and, head and tail with 20-degree troughs each.

Drums and ShaftsOuter conveyor, outer drum and shaft: Drum: 406mm x 970mm | Shaft: 90mm x 2168mm

Outer conveyor, inner drum and shaft: Drum: 406mm x 970mm | Shaft: 75mm x 1450mm

Inner conveyor, outer drum and shaft: Drum: 406mm x 970mm | Shaft: 75mm x 1692mm

Inner conveyor, inner drum and shaft: Drum: 406mm x 970mm | Shaft: 75mm x 1270mm

All end drums are welded steel, crowned faced, secured by Fenlock hubs on high strength (EN8) steel shafts. All head drums are lagged.


Addresss




Belt ScraperCarbite tungsten tipped finger scraper to suit 900mm belt. Belt cleaners are situated at the discharge end on both conveyors, cleaning the drive drums below the tangent point of the head pulley.

BearingsOuter conveyor head drum bearing: 90mm pillow block bearing.

Outer conveyor tail drum bearing: 75mm pillow block bearing.

Inner conveyor head drum bearing: 75mm pillow block bearing.

Inner conveyor tail drum bearing: 75mm pillow block bearing.

GearboxesOuter conveyor direct drive: 6.33:1 shaft mounted gearbox.

Inner conveyor direct drive: 12.68:1 shaft mounted gearbox.

Winch direct drive: 329.69:1 shaft mounted gearbox.

Electric MotorsOuter conveyor motor: 2 x 18.5kw ratio 16.33:1 hollow bore 70mm H1 mounting IP 55 rating

Inner conveyor motor: 2 x 15kw ratio 12.68:1 hollow bore 50mm H1 mounting IP 55 rating

Winch direct motor: 1.1kw ratio 329.69:1 hollow bore 60mm H1 mounting IP 55 rating


Addresss


Dealer Information





Electrics and ControlsElectrical Panel is mounted in weather proof enclosure with 415V/380V, 3 phase, 50 Hz, Allen Bradley starters with Allen Bradley SLC 500 processor allowing the unit to be fully automated or manually operated.

Wheels and AxilsRadial Wheels: 445/65 R22.5 8 stud 50/50 split tyre and rim wheel drive wheels (tractor).

Travelling Wheels: 11 R22.5 10 stud tyre and rim wheel high speed (truck).

HydraulicsJack Leg Cylinders: 90mm bore 700 stroke.

Radial Arm Cylinders: 180mm bore 1200mm stroke.

Telescopic Lift Cylinders: 130mm bore 1900mm stroke fitted with safety check valve.Track: 3 meter c/c track, 300mm shoe, 594mm approx height c/w hydraulic drive.

SafetyThe machines are safety guarded at the back of counterweight and telescopic rams.


Addresss



Transport Dimensions (mm)

Operational Dimensions (mm)

Fully Up and Extended (mm)

Fully Down and Retracted (mm)


Addresss


Dealer Information



Documents

ST36-140 Radial Telescopic Stacker...ST36-140 Radial Telescopic Stacker Component Specification Belt Scraper Carbite tungsten tipped finger scraper to suit 900mm belt. Belt cleaners