SISTORE MX 3G - Siemens Building · PDF fileBuilding Technologies Fire Safety & Security Products SISTORE MX SISTORE MX DVD SISTORE MX 3G SISTORE MX 3G DVD Hybrid Video Recorder Installation

Building TechnologiesFire Safety & Security Products

SISTORE MX SISTORE MX DVD SISTORE MX 3G SISTORE MX 3G DVD Hybrid Video Recorder

Installation Manual (EN) V2.80

Liefermöglichkeiten und technische Änderungen vorbehalten. Data and design subject to change without notice. / Supply subject to availability. © 2009 Copyright by Siemens Building Technologies Wir behalten uns alle Rechte an diesem Dokument und an dem in ihm dargestellten Gegenstand vor. Der Empfänger erkennt diese Rechte an und wird dieses Dokument nicht ohne unsere vorgängige schriftliche Ermächtigung ganz oder teilweise Dritten zugänglich machen oder außerhalb des Zweckes verwenden, zu dem es ihm übergeben worden ist. We reserve all rights in this document and in the subject thereof. By acceptance of the document the recipient acknowledges these rights and undertakes not to publish the document nor the subject thereof in full or in part, nor to make them available to any third party without our prior express written authorization, nor to use it for any purpose other than for which it was delivered to him.

About this document

This document contains instructions for the installation of SISTORE MX and SISTORE MX 3G units. For information on configuration please refer to the Configuration Manual. For information on operation please refer to the User Manual.

Trademarks

SISTORE is a trademark of Fire & Security Products GmbH & Co. oHG.

Microsoft is a registered trademark and Windows a trademark of Microsoft Corporation.

All other product or company names mentioned in this document are trademarks or registered trademarks of their respective owners and are used only for purposes of identification or description.

Contacting us

If you have questions or suggestions regarding the product or this documentation, please contact our Customer Support Center.

Intranet: http:/intranet.sbt.siemens.com/fs/CSC

E-Mail: [email protected]

Tel.: +49 89 9221 8000

Training courses

Siemens Fire & Security Products provides training courses for all products.

https://intranet10.sbt.siemens.com/about_bt/business_units/fs/Customer+Support+Center/

mailto:[email protected]

3

Siemens Building Technologies Fire Safety & Security Products 02.2009

EN

Contents 1 Safety .......................................................................................................5 1.1 Target readers...........................................................................................5 1.2 Work safety information ............................................................................5 1.2.1 Transport...................................................................................................5 1.2.2 Installation .................................................................................................5 1.2.3 Service and maintenance .........................................................................6 1.3 Meaning of the written warning notices ....................................................6 1.4 Meaning of the hazard symbols ................................................................6

2 EU directives ...........................................................................................7

3 Technical data .........................................................................................8 3.1 SISTORE MX / MX DVD...........................................................................8 3.2 SISTORE MX 3G / MX 3G DVD .............................................................10

4 Details for ordering...............................................................................12 4.1 SISTORE MX / MX DVD.........................................................................12 4.2 SISTORE MX 3G / MX 3G DVD .............................................................14

5 Package contents..................................................................................15

6 Description of SISTORE MX / MX DVD................................................16 6.1 Connections und displays on the front side of the device ......................16 6.2 Connections on the back of the device...................................................17 6.2.1 SISTORE MX 3204.................................................................................17 6.2.2 SISTORE MX 3208 - 3232......................................................................18 6.2.3 Trigger and digital inputs.........................................................................19 6.2.4 Digital outputs .........................................................................................19 6.3 Behaviour with overheating.....................................................................20

7 Description of SISTORE MX 3G / MX 3G DVD....................................21 7.1 Connections und displays on the front side of the device ......................21 7.2 Connections on the back of the device...................................................22 7.2.1 Trigger and digital inputs.........................................................................23 7.2.2 Digital outputs .........................................................................................23

8 Installation .............................................................................................24 8.1 Rack installation......................................................................................24 8.2 Tabletop operation ..................................................................................25 8.3 Setting DIP switches (SISTORE MX / MX DVD) ....................................26 8.4 Examples of system design ....................................................................28 8.4.1 Connecting control panel CKA4810........................................................29 8.4.1.1 SISTORE unit..........................................................................................29 8.4.1.2 SISTORE Remote View..........................................................................30 8.4.2 Connecting control panel CKA4820........................................................31 8.4.2.1 SISTORE unit..........................................................................................31 8.4.2.2 SISTORE Remote View..........................................................................32 8.4.3 Connecting the Multimedia Control Panel (SISTORE MX /

RemoteView)...........................................................................................33 8.4.4 Connecting the Siemens LAN camera CCIx1345...................................40 8.4.5 Connecting the CCDA1425 dome camera .............................................41 8.4.6 Connecting the CCDA1435 dome camera .............................................42 8.4.7 Connecting pan-and-tilt unit PT40 ..........................................................43 8.4.8 Connecting pan-and-tilt unit CDD2410 ...................................................44 8.4.9 Connecting SCU pan-and-tilt unit PT40P via controller CDC050x .........44 8.4.10 Connecting SCU pan-and-tilt unit via controller CDCD2417 ..................45

4


8.4.11 Connecting the MX Multi-Channel Box RCI 0601...................................46 8.4.11.1 Connecting cash dispensers..................................................................46 8.4.11.2 Connecting Kebin access readers .........................................................47 8.4.12 Connecting Miniter interface and access reader.....................................48 8.4.13 Connecting cash box systems ................................................................49 8.4.14 SISTORE unit – CKA4820 – SISTORE RemoteView – LAN cameras...50

9 Software (SISTORE unit) ......................................................................52 9.1 Software operation using the virtual keyboard........................................52 9.2 Updating or repairing software................................................................53 9.3 Subsequent installation of software components....................................54

10 Software (SISTORE RemoteView ........................................................56 10.1 System requirements ..............................................................................56 10.2 Installing SISTORE RemoteView............................................................57 10.3 Updating SISTORE RemoteView ...........................................................59 10.4 Subsequent installation of software components....................................60

11 System limits .........................................................................................60

12 Disposal .................................................................................................60

Safety

5


EN

1 Safety

1.1 Target readers

The instructions in this document are designed only for the following target readers:

Target readers Qualification Activity Condition of the

product Installer Technical training for

electrical installations. Installs the product, individual components of the product or replacement parts.

Components of the product are not yet installed or need to be replaced or modified.

1.2 Work safety information

Read the general safety precautions before installing the device. Keep this document for later reference. Always pass this document on together with the product. Please also take into account any additional country-specific, local laws, safety standards or regulations concerning installation, operation and disposal of the product.

Please also read the documentation on the accompanying CD.

Liability claim Do not connect the device to the supply network if it is damaged or any parts are missing.

Do not make any changes or modifications to the device unless they have been approved by the manufacturer.

Use only spare parts and accessories that have been approved by the manufacturer.

Danger of electrical shock on the open device Only qualified personnel should open the unit.

1.2.1 Transport

Keep the packaging material for future transportation. Do not expose the device to mechanical vibrations or shocks.

1.2.2 Installation

Radio interference with other devices in the environment / EMC This is a Class A device. This equipment may cause radio interference in a residential installation. In this case the user is encouraged to perform appropriate measures to correct the interference.

Safety

6


Damage due to unsuitable mounting location Observe the environmental requirements recommended by the manufacturer. See Section 3 Technical data.

Do not operate the device close to sources of powerful electromagnetic radiation.

Do not operate the device in dusty places. The device should only be used for indoor applications. Do not expose the device to mechanical vibrations or shocks. Protect the device against moisture. Place the unit on a stable surface that will hold its weight.

Damage to the device due to lack of ventilation Do not block or cover the ventilation openings of the device. To ensure sufficient ventilation please also read the instructions in this manual.

Do not stack several devices on top of each other and do not place any objects on the device.

Danger of electrical shock/fire hazard/damage to the device due to incorrect connection

Connect the device only to power sources with the specified voltage. Voltage supply requirements can be found on the rating label of the device.

Use the device only in conjunction with a power supply cable that has been approved in your country and complies with the national standards.

1.2.3 Service and maintenance

Do not attempt to service or modify this device yourself. Refer this work to qualified service personnel.

1.3 Meaning of the written warning notices

The severity of a hazard is indicated by the following written warning notices.

Signal word Type of risk CAUTION There is a risk of minor to medium injuries or damage to property. IMPORTANT Malfunctioning may result

1.4 Meaning of the hazard symbols

The nature of the hazard is indicated by icons.

Warning of a hazard

EU directives

7


EN

2 EU directives

This product complies with the requirements of the following European directives. The EU declaration of conformity is available to the responsible agencies at:

Siemens Building Technologies Fire & Security Products GmbH & Co. oHG 76187 Karlsruhe

Germany

European Directive 2004/108/EC „Electromagnetic Compatibility”

Compliance with the European Directive 2004/108/EC has been proven by testing according to the following standards:

Emitted interference: EN 61000-6-4

EN 55022 Class A Interference resistance:

EN 50130-4

European Directive 2006/95/EC „Low-Voltage Directive”

Compliance with the European Directive 2006/95/EC has been proven by testing according to the following standard:

Safety: EN 60950-1

Technical data

8


3 Technical data 3.1 SISTORE MX / MX DVD

SISTORE MX 3204 with 4 video inputs

SISTORE MX 3208 - 3232 with 8, 16 or 32 video inputs

Max. 50 fps, configurable for analogue cameras

Max. 100 fps, configurable for analogue cameras

Recording speed

Max. 100 fps, configurable for max. 32 LAN

cameras

Max. 100 fps, configurable for max. 32 LAN

cameras Video inputs 4 x CCVS (BNC sockets),

1 Vpp/75 Ohm, max. 32 LAN camera

8/16/32 x CCVS (BNC sockets), 1 Vpp/75 Ohm,

max. 32 LAN camera Video outputs 1 x VGA, 2 x CCVS (BNC sockets) 1 x VGA, 4 x CCVS (BNC sockets) Trigger inputs 16 UinB: 5 – 24 V, max. 10 mA 32 UBinB: 5 – 24 V, max. 10 mA Event control Event-triggered recording of individual cameras or camera groups with

configurable time-slot pattern. Events: Alarm contact, motion detection, time control, TCP/IP command

Alarm signalling Via monitor connection, digital output, LAN/WAN to RemoteView station, acoustic signal, e-mail, SMS

Digital inputs 4 for AND operations and system control functions

UBinB: 5 – 24 V, max. 10 mA

8 for AND operations and system control functions

UBinB: 5 – 24 V, max. 10 mA Digital outputs 8 switch/key outputs,

configurable switching (rising or falling edge duration)

U: 5 – 24 V, max. 50 mA

16 switch/key outputs, configurable switching (rising or

falling edge duration) U: 5 – 24 V, max. 50 mA

Interfaces 2x RS485, 1 x LAN, 4 x USB 2.0 (0.5 A), 1 x SCSI, 1 x VGA, 1 x Audio in, 1 x Mic in, 1 x Audio out, optionally: SB0B interface for ISDN

Mouse, keyboard Mouse with USB connection, virtual keyboard (optional) Video standard PAL/NTSC Analog resolution Standard: 352 x 288 pixels

High resolution: 704 x 288 pixels Compression M-JPEG, configurable: variable between 10 and 80 KB Text overlay in the video image Max. 16 characters Font and background colours Freely selectable Storage media Basic unit (E)IDE Memory capacity 250/500/750/1000 GB data memory External storage media Via network connection Display resolution 1024 x 768, 1280 x 1024 Playback Individual images, video sequence (replay rate configurable between 0.1 to

50 times), forward/backward, pause (frozen image) Image search By means of date, time, camera number, recording event, graphic activity

search, logbook, Smartsearch Video display formats 1x1, 2x2, 1 + 5, 3x3, 2 + 8, 4 + 9, 4x4, 6x6 - 4 (32), 7x7 – 1 (48), 8x8 - (64) System self-monitoring function Hardware/software watchdog Power supply 100 – 230 V AC, 50 – 60 Hz, approx. 120 W Power input Appliance inlet Temperature range (operation) 5 – 35 °C

Technical data

9


EN

SISTORE MX 3204 with 4 video inputs

SISTORE MX 3208 - 3232 with 8, 16 or 32 video inputs

Design Embedded Environmental temperature 5 – 45 °C Rel. humidity 20 – 80 % without condensation Dimensions (W x H x D) 430 x 87 x 370 mm

Video compression Colour resolution Video recording always takes place in YUV 4:2:2 true colour format.

The VGA board must be set to 16-bit mode (Hi-Color). Video compression is made in JPEG format.

Video input 4/8/16 external composite inputs, YC signals are not supported.

8/16/24/32 external composite inputs,YC signals are not supported.

Video output 2 outputs: CVBS, YC signals are not supported.

4 outputs: CVBS, YC signals are not supported.

Video standard PAL, NTSC Video scanning frequency PAL: 13.5 MHz

NTSC: 13.5 MHz A/D conversion PAL: 1/100 s (20 ms) per field

NTSC: 1/120 s (16.7 ms) per field Geometric resolution PAL: 704 x 576 pixels with 2 fields

NTSC: 704 x 480 pixels with 2 fields

Optocoupler Trigger and signal inputs Number of trigger and signal inputs 16 32 Trigger edge Positive or negative Triggering of interrupts Yes Voltage range 5 – 24 V DC Input current 12 mA (typ.), protected against polarity reversal Electrical isolation Up to 2500 V Digital inputs Number of digital inputs 4 8 Triggering of interrupts No Voltage range 5 – 24 V DC Input current 12 mA (typ.), protected against polarity reversal Electrical isolation Up to 2500 V Digital outputs Number of digital outputs 8 16 Output current 50 mA (max.), reversible fuse Electrical isolation Up to 2500 V

SISTORE MX systems are configured for DHCP by default. If there is no DHCP server in the network, select the menu sequence Administration> Configuration, then click the button TCP/IP parameters in the Network tab and enter a permanent IP address instead of DHCP. Otherwise there may be quite a long waiting time as the system will wait for a reply from the non-existent DHCP server.

Technical data

10


3.2 SISTORE MX 3G / MX 3G DVD

SISTORE MX 3G

Max. 400 fps, configurable for 16 analog cameras (max. 25 fps / camera) Recording speed Max. 100 fps, configurable for max. 16 LAN cameras

Video inputs 8/16 x CCVS (BNC sockets), 1 Vpp / 75 Ohm, max. 16 LAN cameras

Video outputs 4 x CCVS (BNC sockets) Alarm inputs 16, UB: 5 V Event control Event-triggered recording of individual cameras or camera groups with

configurable time-slot pattern. Events: Alarm contact, motion detection, time control, TCP/IP command, SMTP, HTTP

Alarm signalling Via monitor connection, digital output, LAN/WAN to RemoteView station, acoustic signal, e-mail, SMS

Digital inputs 4 for AND operations and system control functions Digital outputs 4 alarm outputs, configurable switching (rising or falling edge duration)

U: 24 V, max. 50 mA Interfaces 2x RS485, 2 x LAN, 6 x USB 2.0 (0,5 A), 1 x DVI-I, 1 x DVI-D, 16 x Audio in,

4 x audio out Mouse, keyboard Mouse with USB connection, virtual keyboard (optional) Video standard PAL Analog resolution CIF: 352 x 288 pixels

2CIF: 704 x 288 pixels 4CIF: 704 x 576 pixels

Digital resolution (LAN cameras) Max. 5 megapixels (depending on the camera type) Compression M-JPEG, configurable: variable between 10 and 160 KB Text overlay in the video image Max. 16 characters Font and background colours Freely selectable Internal storage media Max.: 4 SATA hard disks (1 TB max. each) Memory capacity SISTORE MX 3G: 1000 – 4000 GB data memory

SISTORE MX 3G DVD: 1000 – 3000 GB data memory External storage media Via network connection Display resolution 1024 x 768, 1280 x 1024, 1920 x 1200 Screen format 4:3, 16:10 Playback Individual images, video sequence (replay rate configurable between 0.1 to

50 times), forward/backward, pause (frozen image) Image search By means of date, time, camera number, recording event, graphic activity

search, logbook, Smartsearch Video display formats 1x1, 2x2, 1 + 5, 3x3, 2 + 8, 4 + 9, 4x4, 6x6 - 4 (32), 7x7 – 1 (48), 8x8 - (64) System self-monitoring function Hardware/software watchdog Power supply 110 – 240 V AC, 50 – 60 Hz, 4 – 2 A Power input Appliance inlet Environmental temperature Operation: 5 – 40 °C

Storage: -20 to +70 °C Rel. humidity 20 – 80 % without condensation Design Embedded Dimensions (W x H x D) 430 x 87 x 440 mm

Technical data

11


EN

SISTORE MX 3G

Video compression Colour resolution Video recording always takes place in YUV 4:2:2 true colour format.

The VGA board must be set to 16-bit mode (Hi-Color). Video compression is made in JPEG format.

Video input 16 external composite inputs, YC signals are not supported. Video output 4 outputs: CVBS, YC signals are not supported. Video standard PAL Video scanning frequency PAL 13,5 MHz A/D conversion PAL 1/100 s (20 ms) per fieldGeometric resolution PAL: 704 x 576 pixels with 2 fields

Optocoupler Trigger and signal inputs Number of trigger and signal inputs 16 Trigger edge Positive or negative Triggering of interrupts Yes Switching voltage 5 V ± 10 % Switching current Max. 5 mA Digital inputs Number of digital inputs 4 Triggering of interrupts No Digital outputs Number of digital outputs 4 Output current 50 mA (max.), reversible fuse Electrical isolation Up to 2500 V

SISTORE MX systems are configured for DHCP by default. If there is no DHCP server in the network, select the menu sequence Administration> Configuration, then click the button TCP/IP parameters in the Network tab and enter a permanent IP address instead of DHCP. Otherwise there may be quite a long waiting time as the system will wait for a reply from the non-existent DHCP server.

Details for ordering

12


4 Details for ordering

4.1 SISTORE MX / MX DVD

Further products and accessories can be found in the Internet: 2Hwww.buildingtechnologies.siemens.com > Products & Systems > Electronic Security > Catalogue Downloads.

Type Part no. Designation Weight*

Without DVD

SISTORE MX 3208 250/200 S24245-F5085-A2 Hybrid recorder, 8 analog cameras,

32 LAN cameras, 250 GB,

100 ips analog, 100 ips digital

approx. 11.0 kg




approx. 11.0 kg




approx. 11.0 kg

With DVD

SISTORE MX 3204 250/150 DVD

S24245-F5085-A1 Hybrid recorder, 4 analog cameras,


50 ips analog, 100 ips digital, with DVD

approx. 11.0 kg





approx. 11.0 kg





approx. 11.0 kg





approx. 11.0 kg

* Unit incl. packing material, accessories that are included in the delivery, and documentation

All SISTORE MX models have enabled video output and SCSI functions and are delivered without keyboard.

The part number (PN) of your SISTORE unit will be found on the rating plate on the bottom of the unit.


13


EN

Accessories (not included in the delivery)

Type Part no. Designation Weight

Activation of 4 SISTORE MX video inputs

S24245-P5097-A4 Enables an additional 4 analog video inputs ./.

Activation of 8 SISTORE MX video inputs

S24245-P5097-A1 Enables an additional 8 analog video inputs ./.

19“ installation kit for SISTORE MX/CX

C24245-A12-D2 Mounting equipment for installation in a 19“ rack 4.0 kg

MX multichannel box

(GAA/ATM)

S24245-F5092-A1 For connection of cash dispensers,

cash box or access control systems

1.2 kg

SISTORE MX hard drive

expansion kit 250 GByte

2GF4811-8CD For the expansion of SISTORE MX as of V2.50 0.8 kg

SISTORE MX hard drive

expansion kit 500 GByte

S24245-B5093-A1 For the expansion of SISTORE MX as of V2.50 0.8 kg

SISTORE RAID8 2000 S24245-B5108-A1 2 TB RAID system 34.8 kg

SISTORE RAID8 3000 S24245-B5108-A2 3 TB RAID system 38.4 kg

USBOBTO8 2GF4811-8CH USB input module - 8 channels with optocoupler function

./.

USBREL8 2GF4811-8CG USB output module - 8 channels with relay function

./.

USBOPTOREL16 2GF4811-8CJ USB input and output modules with 16 optocoupler inputs and 16 relay outputs

./.

USB ISDN module 2GF4811-8FC For use on the SISTORE MX 0.8 kg

SISTORE MX USB mouse A5Q00009353 As a replacement device

SISTORE MX USB keyboard A5Q00009346 For SISTORE MX without keyboard

External USB DVD burner GBQ:S80817 For SISTORE MX without internal DVD burner

CMTC1525 TFT monitor 2GF3124-8AA 15-inch TFT colour monitor for CCTV 6.0 kg



Interface converter

RS232C/RS485

2GF5505-8AH Interface converter RS232C/RS485 0.1 kg

Converter model 4855DSR ./. From roline (please order directly from the manufacturer)

./.

Converter model USB/RS232 ./. From roline (please order directly from the manufacturer)

./.

KeBin access reader ./. From KEBA (please order directly from the manufacturer)

./.

Miniter access reader ./. From STM GmbH (please order directly from the manufacturer)

./.

Multimedia Control Panel (ShuttlePRO2)

./. From Contour Design Ltd. (please order directly from the manufacturer)

./.


14


4.2 SISTORE MX 3G / MX 3G DVD

Further products and accessories can be found in the Internet: 3Hwww.buildingtechnologies.siemens.com > Products & Systems > Electronic Security > Catalogue Downloads.

Type Part no. Designation Weight*

Without DVD

SISTORE MX1608 S54569-C201-A3 SISTORE MX1608 HVR, 1000 GB, 300 fps approx. 11.7 kg

SISTORE MX1616 S54569-C202-A3 SISTORE MX1616 HVR, 1000 GB, 500 fps approx. 11.7 kg

With DVD

SISTORE MX1608 DVD S54569-C201-B3 SISTORE MX1608 HVR, DVD, 1000 GB, 300 fps approx. 11.7 kg

SISTORE MX1616 DVD S54569-C202-B3 SISTORE MX1616 HVR, DVD, 1000 GB, 500 fps approx. 11.7 kg

* Unit incl. packing material, accessories that are included in the delivery, and documentation

All SISTORE MX models have enabled video output functions and are delivered without keyboard.

The part number (PN) of your SISTORE unit will be found on the rating plate on the bottom of the unit.

Accessories (not included in the delivery)


19“ installation kit for SISTORE

MX/CX

C24245-A12-D2 Mounting equipment for installation in a 19“ rack 4.0 kg

MX multichannel box

(GAA/ATM)

S24245-F5092-A1 For connection of cash dispensers,

cash box or access control systems

1.2 kg

USBOBTO8 2GF4811-8CH USB input module - 8 channels with optocoupler function

./.

USBREL8 2GF4811-8CG USB output module - 8 channels with relay function

./.

USBOPTOREL16 2GF4811-8CJ USB input and output modules with 16 optocoupler inputs and 16 relay outputs

./.

USB ISDN module 2GF4811-8FC For use on the SISTORE MX 0.8 kg

SISTORE MX USB mouse A5Q00009353 As a replacement device

SISTORE MX USB keyboard A5Q00009346 For SISTORE MX without keyboard

External USB DVD burner GBQ:S80817 For SISTORE MX without internal DVD burner




Package contents

15


EN


Interface converter

RS232C/RS485

2GF5505-8AH Interface converter RS232C/RS485 0.1 kg

Converter model 4855DSR ./. From roline (please order directly from the manufacturer)

./.

Converter model USB/RS232 ./. From roline (please order directly from the manufacturer)

./.

KeBin access reader ./. From KEBA (please order directly from the manufacturer)

./.

Miniter access reader ./. From STM GmbH (please order directly from the manufacturer)

./.

Multimedia Control Panel (ShuttlePRO2)

./. From Contour Design Ltd. (please order directly from the manufacturer)

./.

5 Package contents

SISTORE MX / MX DVD SISTORE unit Mouse Mains cable 8 x digital I/O connector (SISTORE MX 3204) 14 x digital I/O connector (SISTORE MX 3208 - 3232) Activation form CD with the SISTORE MX application software and complete documentation Installation Manual

SISTORE MX 3G / MX 3G DVD SISTORE unit Mouse Mains cable 2 x 8-pin digital I/O connector 2 x 4-pin digital I/O connector CD with the SISTORE MX application software and complete documentation Installation Manual

Description of SISTORE MX / MX DVD

16


6 Description of SISTORE MX / MX DVD

6.1 Connections und displays on the front side of the device

Fig. 1 Front side of SISTORE MX 3204 and SISTORE MX 3208 - 3232

LED displays on the front side of the device

1 Power Lit green: Power supply, unit in operation 2 Error Lit yellow: Error: Alarm, initializing, overheated 3 Camera Lit yellow: Loss of video 4 Recording Lit red: Recording 5 Hard disk Blinking green: Access to internal hard drive(s)

Connections on the front side of the device

6 USB Connection of 2 USB-enabled devices (e.g. keyboard, mouse, backup hard drive, DVD burner) Please note: The operation of external USB hard drives as a memory expansion is not allowed for technical reasons.

7 Headphones Connection of headphones (without amplifier)


17


EN

6.2 Connections on the back of the device

6.2.1 SISTORE MX 3204

1 2 3 4

5 6 7 8 9 10

Fig. 2 Back side of SISTORE MX 3204

1 Fan 2 Video output 2 video outputs, 50 Hz/60 Hz

Connect the same type of unit here as that on the video inputs (PAL, for example), since otherwise it is not possible to operate the video outputs.

3 ON / OFF Switching the unit on and off 4 Video input 16 video connection jacks

Depending on the model and licence file, up to 32 cameras can be connected.

5 Power supply 100 – 230 V AC, 50 – 60 Hz, 120 W (use only the power supply provided) 6 LAN/USB LAN: connection of a LAN cable (RJ45 network cable)

USB: Connection of 2 USB-enabled devices (e.g. USB-ISDN modem, printer, mouse, keyboard, DVD burner) Please note: The operation of external USB hard drives as a memory expansion is not allowed for technical reasons.

7 COM 1/COM 2 RS485

Connection for control of pan/tilt cameras, CKA48xx control panel or MX multichannel box

8 VGA For connecting a monitor, e.g. CTMC 15/17/19 9 L-out Connection of commercially available speakers or headphones 10 L-in Connection of audio sources 11 MIC Connection of a microphone for voice recording

(such as a standard microphone sold as a commercial PC accessory) 12 SCSI For connection of SCSI RAID system, e.g. SISTORE RAID

Connection: HD68 Standard: Ultra Wide SCSI, Single End Mode

13 Digital I/O input Trigger inputs 1 … 16 14 Digital I/O output Digital outputs 1 … 8 15 Digital I/O control Digital inputs 1 ... 4

Pin assignment

RS-485 socket RS-485 socket PIN 1: NC PIN 6: NC PIN 2: A (TX+/RX+) PIN 7: NC PIN 3: B (TX-/RX-) PIN 8: NC PIN 4: NC PIN 9: NC PIN 5: GND


18


6.2.2 SISTORE MX 3208 - 3232

4

5 6 7 8 9 10

321

Fig. 3 Back side of SISTORE MX 3208 - 3232

1 Fan 2 Video output 4 video outputs, 50 Hz/60 Hz

Connect the same type of unit here as that on the video inputs (PAL, for example), since otherwise it is not possible to operate the video outputs.

3 ON / OFF Switching the unit on and off 4 Video input 32 video connection jacks

Depending on the model and licence file, up to 32 cameras can be connected.

5 Power supply 100 – 230 V AC, 50 – 60 Hz, 120 W 6 LAN/USB LAN: connection of a LAN cable (RJ45 network cable)

USB: Connection of 2 USB-enabled devices (e.g. USB-ISDN modem, printer, mouse, keyboard, DVD burner) Please note: The operation of external USB hard drives as a memory expansion is not allowed for technical reasons.

7 COM 1/COM 2 RS485

Connection for control of pan/tilt cameras, CKA48xx control panel or MX multichannel box

8 VGA For connecting a monitor, e.g. CTMC 15/17/19 9 L-out Connection of commercially available speakers or headphones 10 L-in Connection of audio sources 11 MIC Connection of a microphone for voice recording

(such as a standard microphone sold as a commercial PC accessory) 12 SCSI For connection of SCSI RAID system, e.g. SISTORE RAID

Connection: HD68 Standard: Ultra Wide SCSI, Single End Mode

13 Digital I/O input Trigger inputs 1 … 32 14 Digital I/O output Digital outputs 1 … 16 15 Digital I/O control Digital inputs 1 ... 8

RS-485 socket RS-485 socket PIN 1: NC PIN 6: NC PIN 2: A (TX+/RX+) PIN 7: NC PIN 3: B (TX-/RX-) PIN 8: NC PIN 4: NC PIN 9: NC PIN 5: GND


19


EN

6.2.3 Trigger and digital inputs

The HVR is equipped with optocoupler that run the TTL-compatible trigger inputs of the SISTORE MX via optocoupler and enable the switching of signal levels up to 24 V.

The inputs of the optocoupler are designed for a voltage range of 5 to 24 V.

With the SISTORE MX there are 32 trigger inputs and 8 digital inputs available. These trigger inputs are edge triggered. The trigger edge which is to initiate a trigger event can be selected with the software (SISTORE RemoteView and SISTORE MX).

Input circuitry of the optocoupler

Optokoppler

U1

1K2

RV

5 - 24 V

Digital In

Fig. 4 Optocoupler – input circuitry (example of pin assignment)

The 8 digital inputs can be used to control external events.

6.2.4 Digital outputs

The outputs ground a connected consumer. All outputs can handle a maximum current of 50 mA. Fusing of the outputs is implemented with reversible fuses. All outputs are short circuit proof.

If inductive consumers are connected, we recommend using appropriate protective circuits.

U1

Optokoppler D1 F1

50 mA

Digital Out 5 - 24 V

Fig. 5 Optocoupler – output circuitry (example of pin assignment)


20


6.3 Behaviour with overheating

If the Error LED on the front of the device lights yellow, there are two possible causes:

Overheating of the hard drive The running application cannot be stopped. A new application cannot be started.

Overheating of the processor The device will shut down automatically. When the device has cooled down sufficiently (min. 2 hours), it will boot up automatically.

Possible causes The device was not installed with a minimum clearance of 85 mm on both sides. The ambient temperature is too high. See Section 71H3 72HTechnical data.

Measures 1. Pull the power plug and allow the device to cool down. 2. Wait for at least 2 hours for the device to cool down. 3. Check to ensure there is sufficient clearance on both sides of the device. 4. Measure the ambient temperature. See Section 73H3 74HTechnical data. 5. Connect the power plug again. 6. Restart the unit.

Description of SISTORE MX 3G / MX 3G DVD

21


EN

7 Description of SISTORE MX 3G / MX 3G DVD

7.1 Connections und displays on the front side of the device

Fig. 6 Front side of SISTORE MX 3G / MX 3G DVD

LED indicators when the device is switched on

Lit green: Receiving camera signal Lit orange: Recording Lit red: Alarm, motion detected

1 Video inputs 1 – 16

No indicator: No camera connected, SISTORE MX software has not been started

2 Power Lit green: Power supply, unit in operation Blinking green: Access to internal hard drive(s) 3 Hard disk No indicator: No access to internal hard drive(s) Lit green: Connected to the network Blinking green: Data transmission

4 Network

No indicator: No connection to the network

LED indication when the temperature is too high or too low When the operating temperature of the unit exceeds or falls below a specific threshold, the unit will shut down automatically and switch to waiting mode. At the end of the waiting time (6 min.), the temperature is measured again. If the temperature is back to normal, the unit will be restarted automatically. If the temperature is still too high or too low, the unit cannot be restarted yet. It will however be in stand-by mode and be restarted as soon as the temperature is back to normal.

LEDs 1 and 2 LED 1 flashing red

and orange alternately, LED 2 flashing red

Unit is in waiting mode.

LED 8 Lit green: Unit is in stand-by mode.

1

LEDs 1 and 2 Lit red: Operating temperature still too high/low at the end of the waiting time.

Connections

5 USB Connection of 2 USB-enabled devices (e.g. keyboard, mouse, backup hard drive, DVD burner) Please note: The operation of external USB hard drives as a memory expansion is not allowed for technical reasons.


22


7.2 Connections on the back of the device

Fig. 7 Back side of SISTORE MX 3G / MX 3G DVD

CAUTION

Damage to the device and impairment of electrical safety When voltages are applied to the digital inputs/outputs the device may be damaged and electrical safety may be impaired.

Do not apply voltage to the digital inputs (7) and the alarm inputs (6). Do not apply voltages higher than 24 V to the digital outputs (7).

1 Power supply unit with fan

2 Video output 4 video outputs, 50/60 Hz Connection for 75-Ohm BNC cable Connect the same type of unit here as that on the video inputs (PAL, for example), since otherwise it is not possible to operate the video outputs.

3 Video input IN 16 video inputs Connection for 75 Ω BNC cable

4 Video input LOOP 16 loop-throughs Connection for 75 Ω BNC cable

5 Audio 16 audio inputs (currently not supported) 4 audio outputs (currently not supported)

6 Alarm 16 alarm inputs 7 Digital 4 digital inputs

4 digital outputs 8 RS485 2 ports (ports 3 and 4 are used)

Transparent data channels for control of pan/tilt cameras, CKA48xx control panel or MX multichannel box. NOTE: The software interface Com1 corresponds to port 3. The software interface Com2 corresponds to port 4.

9 DVI-D For connecting a monitor (digital) 10 DVI-I For connecting a monitor (digital/analog)

NOTE: If a monitor is connected using a VGA cable, an adapter is required.

11 LAN 2 x 1 Gigabit network port for a LAN cable (RJ45 network cable) 12 USB Connection of 4 USB-enabled devices

(e.g. USB-ISDN modem, printer, mouse, keyboard, DVD burner) Please note: The operation of external USB hard drives as a memory expansion is not allowed for technical reasons.

13 ON / OFF Switching the unit on and off 14 Power supply 110 – 240 V AC, 50/60 Hz, max. 150 W


23


EN

7.2.1 Trigger and digital inputs

The HVR is equipped with optocouplers that enable the connection of floating contacts. The contacts will be triggered when the inputs are shorted. The switching voltage of the switches is 5 V ±10 %, with a max. switching current of 5 mA. The inputs are provided with suppression circuits to prevent damage to the device when voltages up to 24 V are applied. There are 16 trigger inputs and 4 digital inputs available. These trigger inputs are edge triggered. The trigger edge which is to initiate a trigger event can be selected with the software (SISTORE RemoteView and SISTORE MX).

Input circuitry of the optocoupler

+

_

RV

1K2

Digital In

Optokoppler

UB

Fig. 8 Optocoupler – input circuitry (example of pin assignment)

The 4 digital inputs can be used to control external events.

7.2.2 Digital outputs

The outputs ground a connected consumer. All outputs can handle a maximum current of 50 mA. Fusing of the outputs is implemented with reversible fuses. All outputs are short circuit proof.

If inductive consumers are connected, we recommend using appropriate protective circuits.

U1

Optokoppler D1 F1

50 mADigital Out 5 - 24 V

Fig. 9 Optocoupler – output circuitry (example of pin assignment)

Installation

24


8 Installation

To ensure that SISTORE is shut down properly, we recommend to run the unit from a UPS

(uninterruptible power supply). The UPS will also compensate for brief voltage fluctuations.

8.1 Rack installation

The 19” standard installation kit for the SISTORE unit is designed for the basic RITTAL TS8 network cabinet (width: 800 mm, mounting depth: 461 mm) from RITTAL. In addition to the installation kit, two 19“ mounting rails of type DK-TS are required.

CAUTION The device must be installed with a minimum clearance of 85 mm on both sides. Otherwise the device will shut down automatically due to overheating.

1. Remove the housing base on the unit with a screwdriver. 2. Remove the two front cover attachment screws (M4x6) first on one side of the

unit. 3. Screw one of the corner brackets to the side of the unit with the M4x12

screws (see 75HFig. 10).

CAUTION Use only the M4X12 screws supplied with the installation kit. Screws that are too long may cause damage to the device.

4. Remove the two front cover attachment screws on the other side of the unit. 5. Screw on the second corner bracket with the M4x12 screws. 6. Hang the sliding rails in the mounting rails of the network cabinet. 7. Attach the M6 cage nuts for securing the unit in the mounting rails of the

network cabinet. 8. Place the device on the mounting rails and push it into the cabinet. 9. Attach the unit with the four M6x18 screws and plastic washers to the

mounting rails of the network cabinet (see 76HFig. 10).

Installation

25


EN

Fig. 10 SISTORE MX rack installation (top view)

1 Cabinet type Rittal TS 2 SISTORE unit 3 Corner bracket 2HE complete for MX 19” rack installation 4 End-to-end mounting rail 461 mm for PS 5 Flat-head screw, ISO 7045-M4x12-H-ZN 6 Flat-head screw, ISO 7045-M6x18-H-ZN 7 Washer DIN 125-A-6, 4-PA 8 Cage nut, M6 with contacting

8.2 Tabletop operation

IMPORTANT

Overheating of the device In case of overheating the device will shut down automatically. 1. Check to ensure there is a minimum clearance of 85 mm on both sides of the

device. 2. Check the ambient conditions. See Section 77H3 78HTechnical data. 3. You can place up to three devices on top of each other. 4. Do not place any objects on top of the device. Do not cover the device. 5. Do not place the device in direct sunlight.

Installation

26


8.3 Setting DIP switches (SISTORE MX / MX DVD)

Fig. 11 DIP switches

All DIP switches are set to on by default, i.e. the video inputs are terminated with 75 Ohm.

If the signals are to be looped through the DIP switches must be set to off.

IMPORTANT

Malfunctioning of the SISTORE due to lack of termination If the lines are not terminated correctly the image quality may deteriorate.

Termination should always be made at the end of the line.

1 to 8 (75 Ohm termination)

1 75 Ohm termination Dipsw Assignment 1 VIN13 2 VIN14 3 VIN15 4 VIN16



Installation

27


EN






Installation

28


8.4 Examples of system design

The following figure shows a possible system configuration with one SISTORE unit. For further specific examples please refer to the following chapters.

Fig. 12 System overview with SISTORE unit

For a more detailed description of the connections please refer to Section 79H6 80HDescription of SISTORE

MX / MX DVD or Section 81H7 82HDescription of SISTORE MX 3G / MX 3G DVD.

Installation

29


EN

8.4.1 Connecting control panel CKA4810

8.4.1.1 SISTORE unit

Fig. 13 SISTORE unit – CKA4810 system overview



Prerequisite:

The CKA driver is installed and the icon is displayed in the task bar. See Section 87H9.3 88HSubsequent installation of software components.

1. Connect the converter between the control panel CKA4810 and the SISTORE

unit (see 89HFig. 13). See Section 90H4 91HDetails for ordering92H. 2. Configure the COM1A connection on the control panel for use as an RS232

interface.

Further information on this can be found in the instruction manuals for the control panel CKA4810 and the converter.

3. Start the SISTORE MX application software. 4. Switch to configuration mode. 5. Select the System tab. 6. Mark the checkbox CCTV keyboard. Further information on this can be found

in the SISTORE MX Configuration Manual. 7. Click Apply.

The interface for the control panel is enabled.

Connections

Signal SISTORE unit 9-pin Sub-D socket

Converter Converter 25-pin Sub-D

CKA4810 9-pin Sub-D plug

A (Rx/Tx +) 2 T + B (Rx/Tx -) 3 T - GND 5 7 5 RXD 3 2 TXD 2 3

Installation

30


CKA4810 interface configuration Protocol: SIMATRIX RS232 or SIEMENS IVM Baud rate: 9600 Parity: None

8.4.1.2 SISTORE Remote View

Fig. 14 TSISTORE RemoteViewT – TCKA4810 system overview



Prerequisite:


1. Connect the CKA4810 control panel to the client PC (see 99HFig. 14). 2. Configure the COM1A connection on the control panel for use as an RS232

interface.

Further information on this can be found in the instruction manuals for the control panel CKA4810 and the converter.

3. Start the SISTORE RemoteView application software. 4. Switch to configuration mode. 5. Select the System tab. 6. Mark the checkbox TCCTV keyboard. Further information on this can be found



Connections

Signal Client PC SISTORE RemoteView


GND 5 5 RXD 3 2 TXD 2 3

Installation

31


EN


8.4.2 Connecting control panel CKA4820

8.4.2.1 SISTORE unit

Fig. 15 SISTORE MX – CKA4820 system overview



Prerequisite:


1. Connect the CKA4820 control panel to the SISTORE (see 106HFig. 15). 2. Configure COM1B on the control panel as an RS485 interface.

Further information on this can be found in the instruction manual for the control panel.




Installation

32


Connections



A (Rx/Tx +) 2 5 B (Rx/Tx -) 3 9 GND 5 6


If you want to connect the CKA4820 control panel to a SISTORE via the internal COM1A interface, install the RS-232C/RS-485 interface converter into the connection line. See Section 107H8.4.1 108HConnecting control panel CKA4810.

8.4.2.2 SISTORE Remote View

Fig. 16 TSISTORE RemoteViewT – TCKA4820 system overview



Prerequisite:


1. Connect the CKA4820 control panel to the client PC (see 115HFig. 16). 2. Configure the COM1A connection on the control panel for use as an RS232

interface.


3. Start the SISTORE RemoteView application software. 4. Switch to configuration mode. 5. Select the System tab.

Installation

33


EN

6. Mark the checkbox TCCTV keyboard. Further information on this can be found in the SISTORE MX Configuration Manual.

7. Click Apply. The interface for the control panel is enabled.

Connections

Signal Client PC SISTORE RemoteView


GND 5 5 RXD 3 2 TXD 2 3


8.4.3 Connecting the Multimedia Control Panel (SISTORE MX / RemoteView)

The Multimedia Control Panel (ShuttlePRO2, see Section 116H4 117HDetails for ordering 118H) is not a product of Siemens Building Technologies Fire & Security Products GmbH & Co. oHG. It can be ordered from Contour Design Ltd. (www.contourdesign.com) (product name: ShuttlePRO2). The Multimedia Control Panel has been integrated and tested with SISTORE MX. Siemens Building Technologies Fire & Security Products GmbH & Co. oHG can however not guarantee fault-free operation of the Multimedia Control Panels and does not provide any support. In case of problems with the product, please contact the manufacturer (www.contourdesign.com).

Fig. 17 SISTORE – Multimedia Control Panel system overview

To install the Multimedia Control Panel on a SISTORE without DVD drive, you must carry out the following steps: 1. Copy the files on the accompanying CD onto an external USB storage medium. 2. Plug the storage medium into a USB port on the SISTORE. 3. Launch the file Autorun.exe from the USB storage medium. 4. Proceed with step 4 in subsection Installing the Multimedia Control Panel.

Installation

34


Fig. 18 SISTORE RemoteView – Multimedia Control Panel system overview



Installing the software for the Multimedia Control Panel 1. Connect the Multimedia Control Panel to a USB port on the SISTORE unit or

on the client PC (see 123HFig. 17 and 124HFig. 18). 2. Place the CD in the CD/DVD drive.

The CD will start automatically. 3. If the CD does not automatically start, double click the file Autorun.exe.

The following dialog box opens.

4. Click on INSTALL DRIVER.

Installation

35


EN


5. Click LAUNCH SETUP. The following dialog box opens.

6. Click Next.

Installation

36



7. Mark the checkbox Yes, I agree with all the terms of this license agreement. 8. Click Next.


9. Click Next to install the software in the default directory. The following dialog box opens.

Installation

37


EN

10. Click Next. The software will be installed. The following dialog box opens.

11. Mark the checkbox Open the Contour Control Panel. 12. Click Finish.

The software has been installed. The Contour Shuttle Device Configuration dialog box appears.

Installation

38


Configuring the Multimedia Control Panel

Fig. 19 Contour Shuttle Device Configuration

1. Click Options. The following context menu will open:

2. Select Import settings in the context menu.

Installation

39


EN


3. Navigate to the directory where the SISTORE MX or SISTORE RemoteView application software is installed.

4. Open the file SISTORE MX.pref or SISTORE MX RemoteView.pref. 5. Click Apply. 6. If you also want to use the Multimedia Control Panel with the SISTORE

Player, repeat steps 13 to 17 and import the file SISTOREPlayer.pref. 7. Click OK.

The Multimedia Control Panel is ready for operation.

Information on the operation of the SISTORE MX, SISTORE RemoteView and SISTORE Player application software using the Multimedia Control Panel can be found in the SISTORE MX User Manual.

Installation

40


8.4.4 Connecting the Siemens LAN camera CCIx1345

Fig. 20 Siemens LAN camera CCIx1345 – system overview



1. Install the Siemens LAN camera CCIx1345. Further information on this can be found in the installation manual for the camera.

2. Configure alarm activation for the Siemens LAN camera CCIx1345. Further information on this can be found in the SISTORE MX Configuration Manual.

Installation

41


EN

8.4.5 Connecting the CCDA1425 dome camera

Fig. 21 CCDA1425 dome camera – system overview



1. Connect the dome cameras to the SISTORE (see 133HFig. 21). Further information on this can be found in the instruction manual for the dome camera.

2. Start the SISTORE MX application software. 3. Switch to configuration mode. 4. Mark the checkbox PTZ in the Cameras tab 5. Choose the camera type from the first list box. 6. Choose the interface from the second list box. 7. Click Apply.

The interface for the dome camera is enabled.

Further information on this can be found in the SISTORE MX Configuration Manual.

Connections


CCDA1425

A (Rx/Tx +) 2 Data + B (Rx/Tx -) 3 Data -

CCDA1425 interface configuration Baud rate: 9600 Parity: None Dome CCDA1425

Installation

42


8.4.6 Connecting the CCDA1435 dome camera

Fig. 22 Dome CCDA1435 – CKA4820 system overview



Prerequisite:


1. Connect the dome cameras and the control panel to the SISTORE (see 140HFig. 22). Further information on this can be found in the instruction manuals for the dome camera and the control panel.


in the SISTORE MX Configuration Manual. The interface for the control panel is enabled.

6. Select the Cameras tab. 7. Mark the checkbox PTZ. 8. Choose the camera type from the first list box. 9. Choose the interface from the second list box. 10. Click Apply.

The interface for the dome camera is enabled.


Installation

43


EN

Connections


CCDA1435

A (Rx/Tx +) 2 Data + B (Rx/Tx -) 3 Data -

CCDA1435 interface configuration Baud rate: 9600 Parity: None

8.4.7 Connecting pan-and-tilt unit PT40

Fig. 23 Pan-and-tilt unit PT40 – system overview



1. Connect the pan-and-tilt unit to the SISTORE (see 145HFig. 23). 2. Connect the camera to the SISTORE (see 146HFig. 23).

Further information on this can be found in the instruction manuals for the pan-and-tilt unit, the control unit and the camera.

3. Start the SISTORE MX application software. 4. Switch to configuration mode. 5. Select the Cameras tab. 6. Mark the checkbox PTZ. 7. Choose the camera type from the first list box. 8. Choose the interface from the second list box. 9. Click Apply.

The interface for the camera is enabled.


Connections


CDC0501/0502 (J6)

A (Rx/Tx +) 2 Rx/Tx + B (Rx/Tx -) 3 Rx/Tx -

Installation

44


8.4.8 Connecting pan-and-tilt unit CDD2410

Fig. 24 Pan/tilt drive CDD2410 system overview



1. Connect the pan-and-tilt unit to the SISTORE (see 151HFig. 24). 2. Connect the camera to the SISTORE (see 152HFig. 24).

Further information on this can be found in the instruction manuals for the pan-and-tilt unit, the converter and the camera.

3. Start the SISTORE MX application software. 4. Switch to configuration mode. 5. Select the Cameras tab. 6. Mark the checkbox PTZ. 7. Choose the camera type from the first list box. 8. Choose the interface from the second list box. 9. Click Apply.

The interface for the camera is enabled.


8.4.9 Connecting SCU pan-and-tilt unit PT40P via controller CDC050x

SISTORE MX / MX 3GRS485

CDC0501/CDC0502

CDC0501/CDC0502

Fig. 25 Controller CDC050x – system overview



Installation

45


EN

1. Connect the pan-and-tilt units via controller CDC0501 or CDC0502 to the RS485 port (COM2) of the SISTORE (see 157HFig. 25).

2. Further information on this can be found in the product documentation for the pan-and-tilt unit.

Connections Signal SISTORE unit

9-pin Sub-D socket CDC0502 CDC0501 PT40P

A (Rx/Tx +) 2 Rx/Tx + Rx/Tx - Data + B (Rx/Tx -) 3 Rx/Tx - Rx/Tx - Data -

8.4.10 Connecting SCU pan-and-tilt unit via controller CDCD2417

SISTORE MX / MX 3GRS485

CDCD2417 CDCD2417

Fig. 26 Controller CDCD2417 – system overview



1. Connect the pan-and-tilt units via controller CDCD2417 to the RS485 port (COM2) of the SISTORE (see 162HFig. 26).

2. Further information on this can be found in the product documentation for the pan-and-tilt unit.

Connections


CDCD2417

A (Rx/Tx +) 2 Terminal 1 (Data +) B (Rx/Tx -) 3 Terminal 2 (Data -)

CDCD2417 interface configuration Baud rate: 9600 Parity: Odd Data bits: 8 STOP bit: 1

Installation

46


8.4.11 Connecting the MX Multi-Channel Box RCI 0601

8.4.11.1 Connecting cash dispensers

Fig. 27 MX Multi-Channel Box RCI 0601 and ATM system overview

For a more detailed description of the connections please refer to Section 6 Description of SISTORE

MX / MX DVD or Section 7 Description of SISTORE MX 3G / MX 3G DVD.

1. Connect the MX Multi-Channel Box to the SISTORE unit (see Fig. 27). 2. Connect the cash dispensers to the MX Multi-Channel Box RCI 0601.

Further information on this can be found in the user manual for the MX Multi-Channel Box RCI 0601.

3. Start the SISTORE MX application software. 4. Switch to configuration mode. 5. Select the System tab. 6. Mark the checkboxes Bank mode and Cash dispenser.

Please note that banking mode and cash register mode are mutually exclusive.

7. Click Apply. The settings will be saved.

8. Restart the software. 9. Make the appropriate settings in the Banking tab. Further information on this

can be found in the SISTORE MX Configuration Manual.

Installation

47


EN

8.4.11.2 Connecting Kebin access readers

Fig. 28 MX Multi-Channel Box RCI 0601 and access reader – system overview



1. Connect the MX Multi-Channel Box to the SISTORE (see 172HFig. 28). 2. Connect the access reader to the MX Multi-Channel Box RCI 0601.


3. Start the SISTORE MX application software. 4. Switch to configuration mode. 5. Select the System tab. 6. Mark the checkboxes Bank mode and Cash dispenser. 7. Click Apply.

The settings will be saved. 8. Restart the software. 9. Make the appropriate settings in the Banking tab. Further information on this


Installation

48


8.4.12 Connecting Miniter interface and access reader

Fig. 29 System overview: SISTORE MX – interface und access reader (Miniter)

A Cable (9-pin), plug-plug

2-3, 3-2 B Null-modem cable (9-pin), plug-plug

2-3, 3-2, 4-6, 5-5, 6-4, 7-8, 8-7



1. Connect the interface to the SISTORE (see 177HFig. 29). For this you require the converter 485SD9R (B&B), a 9-pin cable, Sub-D, plug-plug, connections 2–3, 3–2, and a null-modem cable, Sub-D, plug-plug, connections 2–3, 3–2, 4–6, 5–5, 6–4, 7–8, 8–7.

2. Connect pin 7 of the Sub-D connector through an 81-Ohm resistor to 12 V. See the figure below:

1 Pin 7 2 +12 V

3. Connect the access reader (Miniter) to the interface. 4. Start the SISTORE MX application software. 5. Switch to configuration mode. 6. Select the System tab. 7. Mark the checkboxes Bank mode and Cash dispenser. 8. Click Apply.

Installation

49


EN

The settings will be saved. 9. Restart the software. 10. Make the appropriate settings in the Banking tab. Further information on this


8.4.13 Connecting cash box systems

Fig. 30 MX Multi-Channel Box RCI 0601 and cash box system – system overview

For a more detailed description of the connections please refer to Section 6 Description of SISTORE

MX / MX DVD or Section 7 Description of SISTORE MX 3G / MX 3G DVD.

1. Connect the MX Multi-Channel Box(es) to the SISTORE unit (see Fig. 30). 2. Connect the cash boxes to the RCI 0601.


3. Start the SISTORE MX application software. 4. Switch to configuration mode. 5. Select the System tab. 6. Untick the checkboxes Bank mode and Cash dispenser.

Please note that banking mode and cash register mode are mutually exclusive.

7. Click Apply. The settings will be saved.

8. Make the appropriate settings in the Cash box tab. Further information on this can be found in the SISTORE MX Configuration Manual.

Installation

50


8.4.14 SISTORE unit – CKA4820 – SISTORE RemoteView – LAN cameras

Fig. 31 SISTORE MX – CKA4820 – SISTORE RemoteView – LAN cameras system overview

1 CKA4820 optional 2 SISTORE unit 3 Client PC with RemoteView 4 SISTORE MX: max. 64 LAN cameras

SISTORE MX 3G: max. 16 LAN cameras various manufacturers



Prerequisite:


1. Connect the CKA4820 control panel to the SISTORE (see 189HFig. 31). 2. Configure COM1B on the control panel as an RS485 interface.



in the SISTORE MX Configuration Manual. The interface for the control panel is enabled.

Connections



A (Rx/Tx +) 2 5 B (Rx/Tx -) 3 9 GND 5 6

Installation

51


EN


If you want to connect the CKA4820 control panel to a SISTORE via the internal COM1A interface,

install the RS-232C/RS-485 interface converter into the connection line (see 190HFig. 13).

Software (SISTORE unit)

52


9 Software (SISTORE unit)

IMPORTANT

Malfunctioning caused by unauthorized software on the SISTORE unit Install only software products on the SISTORE that have been approved by the manufacturer.

We recommend installing one of the following virus scanners on the SISTORE unit: TREND MICROTM Office ScanTM McAfee Security Center

Please note the following: The virus scanners are not included in the delivery. The utilization of the system's CPU will be increased.

IMPORTANT

Data loss due to virus scan If you run an active virus scan, the recording process may be stopped, resulting in a loss of data.

Run the virus scan after recording has stopped.

9.1 Software operation using the virtual keyboard

Fig. 32 Password entry using the virtual keyboard


53


EN

The SISTORE unit is delivered without keyboard. Entry of the characters of the password and parameter setting can be made using the virtual keyboard.

Alternatively, a USB keyboard is available as an option. See Section 191H4 192HDetails for ordering 193H.

1. Connect the mouse supplied to a USB port. 2. Switch the device on.

The SISTORE MX application software will be started automatically.

3. Click the Login icon . The virtual keyboard will appear.

4. Enter the password by clicking the appropriate letters and characters on the virtual keyboard.

5. Click OK. The system is now ready for operation.

Entries into all other input fields of the system are made in the same manner.

9.2 Updating or repairing software

You may have to reinstall or repair the SISTORE MX application software on a SISTORE unit or on a client PC in case components of the software are damaged. In that case proceed as follows: 1. Place the installation CD in the CD drive. 2. Launch SISTORE_MX_280.exe.



54


3. Select the option Update. All the components that were installed during the previous setup will be reinstalled.

Please note that existing files may be overwritten! The following files will not be overwritten:

files containing the configuration settings, files containing the user management data, and files containing the recorded sequences.

9.3 Subsequent installation of software components

IMPORTANT

Malfunctioning caused by unauthorized software on the SISTORE unit Install only software products on the SISTORE that have been approved by the manufacturer.

Software components of the SISTORE MX application software can be subsequently installed on the SISTORE unit.

1. Place the installation CD in the CD drive. 2. Launch SISTORE_MX_280.exe.


3. Select the option Modify. 4. Click Next.


55


EN


Setup type Description CKA4810 / CKA4820 Drivers for CKA4810 or CKA4820 control panels. USB I/O Drivers for external USB input and output module

(optional, see Section 194H4 195HDetails for ordering 196H)

5. Mark the appropriate checkbox(es). 6. Click Next.


7. Select the option Yes, I want to restart my computer now. 8. Click on Finish.

The selected software component has been installed.

Software (SISTORE RemoteView

56


10 Software (SISTORE RemoteView)

SISSTORE RemoteView is a client application which can be installed independent of the other software components. SISTORE RemoteView is mainly used for the evaluation of video data.

The following components are installed together with SISTORE RemoteView: SISTORE RemoteView SISTORE Player Software codec

10.1 System requirements

SISTORE RemoteView can be installed on any PC in Windows. Operating system Windows XP SP2 or higher, or Windows Vista

Pentium IV 2.6 GHz or higher (when using more than 16 camera, at least 3.0 GHz is required)

Min. 512 MB RAM (recommended: 2 GB RAM with Windows XP), max. 2024 MB RAM

S-VGA graphics card, 1024 x 768 or 1280 x 1024, 16-bit colour depth, graphics memory 64 MB or higher

The graphics card driver must fully support Direct Draw functionality V8.x or higher

Hard disk capacity 100 GB or higher CD-ROM drive MF2 keyboard, mouse Network connection Min. 2 USB ports (2.0) Internet Explorer 6.x or higher Monitor with min. 17-inch screen Display resolution 1024 x 768 or 1280 x 1024 pixels Optional: Laser printer or inkjet printer Optional: CD/DVD burner


57


EN

10.2 Installing SISTORE RemoteView

Prerequisites: Windows XP SP2 or higher: To log into the system, the user must at least have main user or rather admin user rights.

Windows Vista: To log into the system, the user must admin user rights.

The installation program will start automatically when the CD is inserted if your operating system has

the appropriate configuration.

1. Launch the file SISTORE_MX_RemoteView_280.exe by double clicking on it. The following dialog box opens.

2. Select the desired language and click OK.


3. Click Next.


58



4. Click Next. The following dialog box opens.

5. Select RemoteView and click Next. The Select program folder dialog box opens.

6. Do not change the destination folder. Click Next.


59


EN

The following warning dialog is displayed:

7. Close all programs and click OK. When installation is completed, the window InstallShield Wizard Complete is displayed.

8. Click on Finish.

It is not necessary to restart your computer. SISTORE RemoteView is immediately ready to be used.

10.3 Updating SISTORE RemoteView

Prerequisite: To log into the system, the user must at least have main user or rather admin user rights.

1. Launch the file SISTORE_MX_RemoteView_280.exe. The following dialog box opens.

2. Select the option Update. 3. Click Next.

The update will be performed automatically. It is not necessary to restart your computer after completion of the update.

System limits

60


10.4 Subsequent installation of software components

This applies to the driver for the CKA48xx control panel. See Section 197H9.3 198HSubsequent installation of software components.

11 System limits

LAN

SISTORERemoteView

SISTORERemoteView

1 n. . .

SISTORE MX / MX 3G

1 32...

SISTORE MX / MX 3G

1 32...

. . .

1 n...

1 . . . n. . .

Fig. 33 SISTORE MX system in multi-server mode

Up to 32 analog camera can be connected to each SISTORE unit. Each SISTORE unit can connect to up to 64 LAN cameras. Each SISTORE RemoteView station can connect to up to 10 SISTORE units at the same time.

Each SISTORE RemoteView station can access up to 960 cameras. Up to 64 SISTORE RemoteView stations can simultaneously connect to the same SISTORE unit.

12 Disposal

All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.

This crossed-out wheeled bin symbol on the product means the product is covered by the European Directive 2002/96/EC.

The correct disposal and separate collection of your old appliance will help prevent potential negative consequences for the environment and human health. It is a precondition for reuse and recycling of used electrical and electronic equipment. For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product.

Issued by Siemens Building Technologies Fire & Security Products GmbH & Co. oHG D-76181 Karlsruhe www.buildingtechnologies.siemens.com

© 2009 Copyright bySiemens Building Technologies

Data and design subject to change without notice.Supply subject to availability.

Printed in the Federal Republic of Germany on environment-friendly chlorine-free paper.

Document no. A6V10065207 Edition 13.02.2009

Documents

SISTORE MX 3G - Siemens Building · PDF fileBuilding Technologies Fire Safety & Security Products SISTORE MX SISTORE MX DVD SISTORE MX 3G SISTORE MX 3G DVD Hybrid Video Recorder Installation