short name: FD.N*gasket for flange

DIN 2690/ EN 1514-1 type IBC

technical product sheet

Shore S DN D d PN Ausf Art.-Nr.

65 2,0 15 50 22 10-40 FD-021-000

65 2,0 15 50 22 10-40 silikonfrei FD-021-S00

65 2,0 20 60 28 10-40 FD-026-000

65 2,0 20 60 28 10-40 silikonfrei FD-026-S00

65 2,0 25 70 35 10-40 FD-033-000

65 2,0 25 70 35 10-40 silikonfrei FD-033-S00

65 2,0 32 82 43 10-40 FD-042-000

65 2,0 32 82 43 10-40 silikonfrei FD-042-S00

65 2,0 40 92 49 10-40 FD-048-000

65 2,0 40 92 49 10-40 silikonfrei FD-048-S00

65 2,0 50 107 61 10-40 FD-060-000

65 2,0 50 107 61 10-40 silikonfrei FD-060-S00

65 2,0 65 127 77 10-40 FD-076-000

65 2,0 65 127 77 10-40 silikonfrei FD-076-S00

65 2,0 80 142 90 10-40 FD-088-000

65 2,0 80 142 90 10-40 silikonfrei FD-088-S00

65 2,0 100 162 115 10+16 FD-114-000

65 2,0 100 162 115 10+16 silikonfrei FD-114-S00

65 2,0 125 192 141 10+16 FD-139-000

65 2,0 125 192 141 10+16 silikonfrei FD-139-S00

65 2,0 150 218 169 10+16 FD-168-000

65 2,0 150 218 169 10+16 silikonfrei FD-168-S00

65 2,0 200 273 220 10+16 FD-219-000

65 2,0 200 273 220 10+16 silikonfrei FD-219-S00

65 2,0 250 328 274 10 FD-273-00A

65 2,0 300 378 324 10 FD-323-00A

65 2,0 350 445 368 10 FD-355-00A

65 2,0 400 490 420 10 FD-406-00A

65 2,0 500 595 520 10 FD-508-00A

65 2,0 600 695 620 10 silikonfrei FD-609-S0A

65 2,0 700 810 712 10 silikonfrei FD-711-S0A

available material: NBR

Flanges › other › gaskets › elastomer › NBR

created 22.01.2022 19:15 1/3

Shore S DN D d PN Ausf Art.-Nr.

created 22.01.2022 19:15 2/3

NBR - black

Nitrile rubber

Elastomer with better resistance and thermal properties than chloroprene.

> Good resistance against hydrocarbons and oils

> Not suitable for chlorohydrocarbons, esters, ketones, and strong oxidation media

> Good mechanical load-bearing capacity

> Available in thickness of 1 - 6 mm

Elastomer-Selection

Technical data

Designation Hardness Density Temperature Strength Elong. to breakEPDM 50 50 Shore A 1,06 g/cm³ -40 to +100°C 9 MPa 500%

EPDM 65 65 Shore A 1,20 g/cm³ -40 to +130°C 7 MPa 300%

NBR 65 65 Shore A 1,45 g/cm³ -20 to + 70°C 5 MPa 200%

Hypalon 70 Shore A 1,47 g/cm³ -30 to +120°C 8 MPA 180%

Viton 75 Shore A 2,00 g/cm³ -10 to +275°C 9 MPA 340%

Resistance

Designation Ozone Oil Acid BasesEPDM 50 + - + +

EPDM 65 ++ - + +

NBR 65 - ++ - -

Hypalon ++ + ++ ++

Viton ++ ++ + +

- = low, + = good, ++ = very good resistant

The qualities listed above can only be used at low inner pressures. The specifications

are guidelines and not assured properties and must in be examined based on the particular mounting situation.

created 22.01.2022 19:15 3/3