SE Training for VNP - IPRAN Project

SmartedgeO&m hands on

VNP dedicated training document

Prepared: OKV/ABA Thuan do

SmartEdge Operation & Maintenance | VNP docs | 2012-09-27 | Page 2

AGENDA

1 SE & SSR Introduction

2

3

SmartEdge Basic

IGP Configuration & Verification

Summary

4 L3VPN iBGP Configuration & Verification

5 VRRP Configuration & Verification

Summary6 Summary


SE and ssr introduction

SmartEdge Product Portfolio

XCRP4 capacity

SmartEdge in IPRAN

SSR Product Portfolio


SmartEdge product portfolio

SmartEdge 1200 SmartEdge 800 SmartEdge 600 SmartEdge 400 SmartEdge 100

PRODUCT CAPACITY RACK UNITS

NUMBER OF

LINE CARDS /

SLOTS

Power

Consumption

SE100 12G 2 MIC only 37.5mW

SE400 80G5 (AC)or 6

(DC)4 / 6

5.5mW

SE600 240G 7 6 / 8 10.7mW

SE800 240G 9 12 / 14 7.5mW

SE1200 480G 16 12 /14 15mW


XCRP4 capacity

System

Circuit

Count

(VLAN, PPP,

DHCP/CLIPs)

Bring Up Rate

circuits/sec

(PPP/CLIPs) VLL

2547

VPNs

Routes

IPV4/IPV6

Cross

Connects

57K 50 to 100 96K 3K 2M/300K 48K

256K 80 to 350 256K 8K 4M/300K 128KXCRP4

XCRP3


Smartedge in ipran

OSSWCDMA RBS Site

GSM RBS Site

STN

/SIU

Transport network

(L2/L3)Site

switches

BSC/RNC Site

Firewalls

(RAN SEGws)

BSC LAN

Switches

BSC/RNC

CPE

Time

Servers

IP RAN Reference Solution

IPsec tunnel

CPE

RBS

RBS Site

Firewall

(RBS SEGw)

RAN Backhaul

IP RANIP RAN

SmartEdge

SmartEdge


SSR product portfolio

*HW ready/Initial

SSR 8004 SSR 8010 SSR 8020

SlotsSlotsSlotsSlots 4 10 20

Port DensityPort DensityPort DensityPort Density160x1G, 40x10G,

8x40G, 4 x 100G

400x1G, 100x10G,

20x40G, 10x 100G

800x1G, 200x10G,

40x40G, 20x 100G

Backplane FD CapacityBackplane FD CapacityBackplane FD CapacityBackplane FD Capacity3.2 Tbps 8 Tbps 16 Tbps

Initial Simplex CapacityInitial Simplex CapacityInitial Simplex CapacityInitial Simplex Capacity0.8 Tbps 2 Tbps 4 Tbps

Full Duplex Slot Full Duplex Slot Full Duplex Slot Full Duplex Slot Capacity*Capacity*Capacity*Capacity*

400/100 Gbps 400/100 Gbps 400/100 Gbps

Height (RU)Height (RU)Height (RU)Height (RU) 8 21 38

Units/ 7 ft rackUnits/ 7 ft rackUnits/ 7 ft rackUnits/ 7 ft rack 4 2 1

Initial PowerInitial PowerInitial PowerInitial Power ~4 kW ~7 kW ~11 kW


AGENDA


2

3

SmartEdge Basic


Summary



Summary6 Summary


Smartedge basic

Context, Interface, & Binding Architecture

Command Line Interface

Configuration & File Management

Basic Daily Check


Context, interface, binding


Command line interface


Command line


Configuration & file mgmt


Basic daily check


BASic daily check


Basic daily check


AGENDA


2

3

SmartEdge Basic


Summary



Summary6 Summary


Ospf database


debug


AGENDA


2

3

SmartEdge Basic


Summary



Summary6 Summary


Example of mpls backbone confcontext local

!

interface inter-PE01-P01 p2p

description inter-site connection between SE600-1 and Huawei P1 - Thanh Thai

ip address 10.149.235.154/30

!

interface intra-PE01-PE02 p2p

description intra-site connection between SE600-1 and SE600-2

ip address 10.149.235.161/30

!

interface loBB loopback

description loopback for BB functionality (IGP,BGP,MPLS,etc.)

ip address 1.1.1.59/32

!

router ospf 1

router-id 1.1.1.59

area 0.0.0.0

interface inter-PE01-P01

network-type point-to-point

interface intra-PE01-PE02

network-type point-to-point

interface loBB

passive

!

router mpls



interface loBB

!


Example of bb conf (cont)

!

router ldp

router-id 1.1.1.59



interface loBB

!

!

router bgp 65512

router-id 1.1.1.59

maximum retain-time 360

address-family ipv4 vpn

nexthop triggered delay 0

!

peer-group PE_RR internal

password vin@ph0ne

update-source loBB

no address-family ipv4 unicast

address-family ipv4 vpn

!

neighbor 1.1.1.249 internal

peer-group PE_RR

!

neighbor 1.1.1.250 internal

peer-group PE_RR

!


ex of l3vpn context (vrf) config

!

context Iuc-SRAN vpn-rd 65512:22017

!

interface vlan105

description ** IuPS/IuCS/Iur CP1 **

ip address 10.209.4.129/29

!

router bgp vpn

address-family ipv4 unicast

export route-target 65512:1036 65512:22017

import route-target 65512:22017

redistribute connected

redistribute static

!


In our network[local]NTNRTR01#ping mpls ldp 1.1.1.116/32 1 debug

:se_mpls_ping :-F :1.1.1.116 :-f :32 :-t :1 :-c :1 :-d :-z :0x40080001

ping_type = 1

Got a Ping query type 1 context 0x40080001 timeout 1 send_mode 0 count 1

Ping will be sent for LDP IPV4 FEC 1.1.1.116/32 cct 255/3:511:63:31/0/1/2231, adj id 0x300053, top label 0x41f

Sending 1 100-byte MPLS echos to LDP 1.1.1.116/32, source 1.1.1.59,

timeout is 1 second, send interval is 0 msec:

Sending ping 1 at sec: 1348828133 usec: 236922 len 68

Adjacency ID: 0x300053 Flags: 0x1 Exp/TTL: 0xcff

Sending to slot: 0

Number of bytes sent 100 on IP sock

Recvagain

Setting recv socket

Received pkt len=68

Received Echo Request 1 sent sec: 1348828133 usec: 236922 at sec: 1348828133 usec: 246587

Received MPLS echo REPLY from 1.1.1.116, len 68

Processing LSP response, error code 3 subcode 1

!Remaining: 20 TLV: 16 tlv-len: 12

Remaining: 0 TLV: 20 tlv-len: 16

---- MPLS PING Statistics----

1 packets transmitted, 1 packets received no error, 0.0% packet loss/error

round-trip min/avg/max/stddev = 9.665/9.665/9.665/0.000 ms[local]NTNRTR01#sh mpls lsp ldp

Codes : S - MPLS-Static, R - RSVP, L - LDP, B - BGP

Type Endpoint Direct Next-hop Out Label Adjacency Id State

L 1.1.1.1/32 10.149.235.153 1334 0x300001 Up

L 1.1.1.2/32 10.149.235.153 1234 0x300003 Up

- - - Ormitted - - -

L 1.1.1.111/32 10.149.235.153 3 0x300051 Up

L 1.1.1.112/32 10.149.235.153 1051 0x300099 Up

L 1.1.1.116/32 10.149.235.153 1055 0x300053 Up


L 203.162.23.246/32 10.149.235.153 1222 0x3000fd Up

[local]NTNRTR01#


Traceroute example

[OAM-RNC-SRAN]NTNRTR01#traceroute 10.149.31.195 source 10.209.4.146

se_traceroute to 10.149.31.195 (10.149.31.195) from 10.209.4.146, 30 hops max, 40 byte packets

1 10.149.235.153 (10.149.235.153) 33.241 ms 34.126 ms 33.013 ms

2 10.149.241.161 (10.149.241.161) 33.024 ms 32.664 ms 32.050 ms

MplsLabel: 16340 MplsExpBits: 0 TTL: 255



3 10.149.241.73 (10.149.241.73) 32.001 ms 31.754 ms 31.951 ms



4 10.149.233.157 (10.149.233.157) 32.974 ms 32.650 ms 32.012 ms



5 10.149.232.197 (10.149.232.197) 31.862 ms 31.699 ms 32.036 ms


6 10.149.232.198 (10.149.232.198) 31.974 ms 31.582 ms 32.022 ms

7 192.9.200.14 (192.9.200.14) 33.072 ms 33.760 ms 32.951 ms

8 10.149.31.195 (10.149.31.195) 32.026 ms 34.591 ms 32.028 ms

[OAM-RNC-SRAN]NTNRTR01#


AGENDA


2

3

SmartEdge Basic


Summary



Summary6 Summary


VRRP configuration example

context Iub-SRAN vpn-rd 65512:22023

!

interface vlan2701

description ** Iub vlan2701 **

ip address 10.209.223.2/27

vrrp 11 backup

virtual-address 10.209.223.1

priority 110

preempt hold-time 90

!

PE1context Iub-SRAN vpn-rd 65512:22023

!

interface vlan2701

description ** Iub vlan2701 **

ip address 10.209.223.3/27

vrrp 11 backup

virtual-address 10.209.223.1

priority 90

preempt hold-time 90

!

PE2


VRRP verification example

Iub-SRAN]BLURTR01#sh vrrp

--- VRRP Virtual Router vlan2701/11 (Backup) ---

State : Master Last Event : Master Timeout

Priority : 110 Advertise Int : 1

Last Adv Source : 10.209.223.3 Up Time : 3d 18:03:25

Preempt : Yes Master Down Int : 3

Preempt HT (sec) : 90 Skew Time (u-sec) : 570312

Auth Type: : None Key Chain :

Connected Route : No

Address List:

10.209.223.1


State : Backup Last Event : Master Preempt







Address List:

10.209.223.33


PE1[Iub-SRAN]BLURTR02#sh vrrp


State : Backup Last Event : Master Preempt







Address List:

10.209.223.1


State : Master Last Event : Master Timeout







Address List:

10.209.223.33


PE2


Vrrp verification

[Iub-SRAN]BLURTR01#debug vrrp ?

all Debug all VRRP

arp Debug Address Resolution Protocol (ARP) interaction

general Debug general operation

packet Debug protocol packets

pktio Debug packet I/O

ppa Debug Fast VRRP PPA interaction

rcm Debug Router Configuration Manager (RCM) interaction

rib Debug Routing Information Base (RIB) interaction

rpm Debug Router Policy Manager (RPM) interaction

snmp Debug SNMP interaction

state Debug virtual router state

[Iub-SRAN]BLURTR01#debug vrrp packet ?

WORD Interface name

error Packet errors

receive Packet reception

send Packet transmission

[Iub-SRAN]BLURTR01#debug vrrp packet vlan2701 ?

1..255 Virtual Router identifier

[Iub-SRAN]BLURTR01#debug vrrp packet vlan2701 11

[Iub-SRAN]BLURTR01#term mon

[Iub-SRAN]BLURTR01#Sep 28 11:06:10: [0007]: %VRRP-7-PACKET_SEND: 10.209.223.2->224.0.0.18 Type: 0x21 ID: 11 Pri: 110 Cnt: 1 Auth: None Int: 1 Chk: 0x871f

Sep 28 11:06:10: [0007]: %VRRP-7-PACKET_SEND: Addrs: 10.209.223.1

Sep 28 11:06:11: [0007]: %VRRP-7-PACKET_SEND: 10.209.223.2->224.0.0.18 Type: 0x21 ID: 11 Pri: 110 Cnt: 1 Auth: None Int: 1 Chk: 0x871f

Sep 28 11:06:11: [0007]: %VRRP-7-PACKET_SEND: Addrs: 10.209.223.1

Sep 28 11:06:12: [0007]: %VRRP-7-PACKET_SEND: 10.209.223.2->224.0.0.18 Type: 0x21 ID: 11 Pri: 110 Cnt: 1 Auth: None Int: 1 Chk: 0x871f


AGENDA


2

3

SmartEdge Basic


Summary



Summary6 Summary


Open discussion

Question

answer

Documents

SE Training for VNP - IPRAN Project