banner stands

smart banner 01SB-S1-3The Smart Banner 01 is a premium single-sided retractable banner stand that offers a quick and easy interchangeable graphic cassette allowing you to change your graphic on the fly. The Smart Banner 01 also offers an integrated extrusion channel used to attach an optional literature rack and table.

dimensions:Hardware Graphic

additional information:

- Single-sided- Drop-in interchangeable graphic cassette- Silver finish with black end caps- NEW accessory channel featured on the top of the unit (to add a literature pocket or arm table accessory)

features and benefits:- Integrated pole storage- Comes with base, top rail, twist and lock NEW telescopic pole, and

premium carry bag- Graphic tensioner- Anti-slip strips along base- Lifetime warranty against manufacturer defects

Assembled Unit: 36”(w) x 87”(h) x 8.5”(d) approx.914mm(w) x 2210mm(h) x 216mm(d)

Base Dimensions:36”(w) x 3.5”(h) x 8.5”(d) approx.914mm(w) x 89mm(h) x 216mm(d)

Total graphic area: 32.9”(w) x 95”(h)835.66mm(w) x 2413mm(h)

Total visual area: 32.9”(w) x 83.5”(h)835.66mm(w) x 2120.9mm(h)

Please be sure to include the 1/2” bleed at the top & 11” bleed at the bottom.

Graphics printed on 8 oz. Oxford using the dye-sublimation printing process will need an extra 1” bleed around the perimeter.

Refer to related graphic template for more information.

Shipping Dimensions: 39”(l) x 10”(w) x 5”(h)991mm(l) x 254mm(w) x 127mm(h)

Shipping Weight - with graphic16 lbs / 7 kg

Shipping

Graphic Materials:11 mil. UV printed supreme melanexpremium 100% opaque fabric14 oz. solvent printed anti-curl vinyl

NEW Optional Banner Stand Accessories:AKIT-1S1L - Stand-off rectangle black counter top and stand-off literature pocket

AKIT-1S - Stand-off rectangle counter top is available in black thermoform only.

AKIT-1L - Stand-off literature pocket

WARNING: Always attach graphic to base and top rail before removing the locking pin. After fitting, the graphic should be left for 24 hours before use to ensure the adhesive bonds sufficiently. Opening the base will void the product warranty.

Add lights to any of our banner stands.LV4 and L9B are recommended.

08.12.15 © Nimlok Display and Exhibit Solutions Worldwide. For questions contact your local Nimlok distributor

New Banner Stand Accessories:easy connection with cam lock

and channel

Integrated pole storage

set-up instructions

graphic rail attachment (metal insert)

quick slide top rail attachment (plastic insert)

Secure pole(s) in the base of standTwist telescopic pole to extend 1 2 3 4Gently lean the unit back and pull the graphic up by the toprail

1 2 3 4

5

Leveling feet located under unit

Metal Insert

Metal Insert

Metal Insert

Peel film to expose adhesive; place metal insert from graphic rail on top back side of the graphic point

Loosen each screw from the rail using provided allen key and remove metal insert (do not remove screws)

Press down on the metal insert to make sure adhesive is secure on graphic

Insert the metal insert with graphic attached into the top graphic profile rail

Tighten the screws back in place to hold metal insert and graphic with an allen key 1 2 3

top slider

printed side down

Remove top slider from graphic railRemove film to expose adhesive on top slider

Align and apply to top slider on the top front of graphic

graphic to base attachment

3

74

8

5 6

Line the bottom of the back of graphic print with adhesive tape on white leader strip

Slowly retract the graphic back into the base

Once aligned pull adhesive tape slowly while applying pressure to graphic to adhere tape

Place interchangeable cartridge back into the outer cartridge with graphic retracted back in

Place additional mask-ing tape to the back of the graphic for extra protection

Remove pin while holding onto the graphic so the graphic does not retract back in quickly

.

1Flip open the cassette door 2Carefully remove the cassette from the outer cartridge4Insert graphic onto graphic rail

top rail slider

graphic back

graphic front

WARNING: Always attach graphic to base and top rail before removing the locking pin. After fitting, the graphic should be left for 24 hours before use to ensure the adhesive bonds sufficiently. Opening the base will invalidate the product warranty.

check out these related products:

We continue to improve and modify our product range and reserve the right to vary the specifications without prior notice. All dimensions and weights quoted are approximate and we accept no responsibility for variance. E&OE. See Graphic Templates for graphic bleed specifications.

rollup 04 rollup 05rollup 02 rollup 03rollup 01

rollup DS 01rollup 06 rollup DS 02 smart banner 01 smart banner 02