ROLLER BLINDS - Quattro Shading · • Suitable for perpendicular windows with a maximum of 20 degrees incline from vertical. • Suitable for Single and Double Roller blinds

SECT: RollerDATE: Feb 2016PAGE: 1

FOUR TH GENERA TION SHADIN GS YSTEM S

SPE

CIF

ICA

TIO

NS

Hardware Overview ................................... 1 - 2

• RollEase® System .................................. 1

• Clutch ........................................................ 1

• Pin End ...................................................... 2

• Control Chain .......................................... 2

• Spring Assist ............................................ 2

Hardware Options ...................................... 3 - 7

• Multi-Link Blinds .................................... 3

• Double Roller .......................................... 3

• Roller Blind Wire Guide ....................... 4

• Roller System .......................................... 5

• Blocco Overview ............................. 5

• Maximum Cassette Size and

Fabric Type ......................................... 6

• Blocco Single Unit .......................... 6

• Blocco Multi-Link Units ................. 7

• Key Numbers and Description ... 7

• Fascia ......................................................... 8

• Square ................................................. 8

• Curved ................................................ 8

• Double ................................................ 8

Hardware ....................................................9 - 11

• Front and Back Roll Combinations .. 9

• Recess Measurements .......................10

• Bottom Rails ..........................................10

• Brackets and Cover Plates ....... 11 - 12

• Single Roller Options ................ 13 - 14

• Maximum Size Guidelines ................13

• Double Roller Option ................ 15 - 16

Light Gaps ................................................17 - 18

• Manual Operation ...............................17

• Motorisation .........................................18

Introduction to Fabric ................................... 19

Roller Blinds Index

ISSU

E: R

B-01

-002

ROLLER BLINDSINDEX

SPE

CIF

ICA

TIO

NS



HARDWAREOVERVIEW

RollEase® system incorporates various operating systems for an entire range of coordinated, premium commercial/residential roller blind products. Colours available for the RollEase® Clutch Controller, Pin End, Brackets, Bracket Cover Plates and Bottom Rail End Caps are: White, Black.

Clutch Sleek, curved design and glass filled (GF) construction clutch system afford cleaner appearance, quieter performance, added strength and durability backed by the RollEase® lifetime clutch warranty.

Powder Coated Steel Bracket

RollEase Clutch Controller

Aluminium Tube

Powder Coated Steel BracketPin End

HOW IT WORKSA clutch utilises a wrap spring which can either be tightened or loosened on an inner core. Push on one side of the spring tang and the spring diameter decreases locking the clutch and prevents any movement. Push the tang on the other side and the spring opens, allowing free movement. The clutch is divided into two separate interior, interlocking cores, the first of which is on the outside (blind tube housing) where the roller blind tube is attached (fabric is rolled onto the tube). The inner core is attached to the cord guard. Both cores have cams which are arranged to push on a particular side of the spring tang. With Velvetrol™, this core is open on two opposing sides. Velvetrol™ enables the spring tangs to apply a balanced force on both sides at the same time allowing a more smooth and even distribution of forces.

The pulley has a cam on both sides which is positioned in such a way that when the pulley is moved in either direction (by pulling on the bead chain) it pushes against the spring tang opening the spring’s diameter and allowing the blind to move up and down. Release the bead chain and the spring automatically returns to its original, closed shape, locking the blind in position.

The blind tube housing has a cam positioned so that the force of the hanging blind pushes on the side of the spring tang locking it to the inner core. The weight of the blind helps keep the blind locked. The more weight on the blind, the tighter the spring locks. The RollEase® patented, balanced core Velvetrol™ multi-spring configuration distributes the interior forces evenly over the inner core and offers the industry’s smoothest pull. The ratio between the bead chain pulley and the blind tube provides a mechanical advantage, allowing the pull forces to raise a blind to be less than the actual weight of the blind.

Bracket Cover Plate

ISSU

E: R

B-01

-002



SPE

CIF

ICA

TIO

NS

Control ChainThe control chain for the RollEase® clutch system is supplied with either a plastic beaded chain with polyester cord or nickel plated steel chain. We recommend the plastic beaded chain with polyester cord because it is stronger, contains no risk of corrosion and runs more quietly when the blind is raised and lowered. The plastic beaded chains are thermally fused 0.175”Dia. plastic bead onto a heavy duty 0.065” Dia. continuous nylon cord. Colours available: White, Black.

Spring AssistTo assist with lifting of larger blinds, the RollEase® spring assist system combines our advanced, patented Skyline clutch system technology with a spring booster. This feature reduces the chain pull force necessary to raise and lower heavy blinds with fabric and bottom bar weight up to 6.8kg (on 50mm tube) to an average of approximately 2kg pull force at the chain. For very heavy

blinds weighing more than 6.8kg and up to 18kg (on 50mm tube), we recommend use of the Galaxy

Series 400 (G400) geared clutch with spring assist, which will lower the pull force to

around 2.5kg at the chain.

Pin EndThe RollEase® Skyline 38mm spring loaded pin-end plug allows for easier installation of the blind into the bracket. The spring loaded pin maintains a constant tension on the blind assembly within the bracket preventing the blind from rolling out of the brackets and reducing drag on the drive system. The pin-end consists of an outer stationary housing and is made of glass reinforced nylon. The bearing surface is a spring loaded pin end engaged into the centre of the housing, made of proprietary General Electric Plastics lubricated PF30 material. The bearing surface provides smooth wear resistance operation. Colours available: White, Black.

Idler Spring Assist - MD Square

Shaft

Retainer Spring Assist-MD

Spring MD right

Sleeve

Retainer Square Shaft

Driver Spring Assist - MD

ISSU

E: R

B-02

-002

HARDWAREOVERVIEW

SPE

CIF

ICA

TIO

NS



Double Roller A double roller system has been developed for customers who require both a transparent solar screen fabric and a block-out fabric on the same window. A double roller can also be used when multiple-link blinds are required. Control operations can either be manual or motorised.

Multi-Link BlindsRollEase® has developed a superior multi-link system, allowing multi-link blinds for wide or multi panel glazing without compromising operation. The multiple-link system includes a patented

adjustment wheel which allows for precise adjustments in the roller blind height from one linked roller blind to the other providing infinite adjustability.

Up to three roller blinds can be linked together with an option of manual or motorisation operating

systems.

Clutch Multi-link Bracket Multi-link Bracket Pin End

Powder Coated Steel Bracket RollEase®

Clutch Controller

Powder Coated Steel Bracket

Tube AdapterDrive Shaft

Multi-link Universal Bracket

Adjustable WheelPin End

Drive Insert

ISSU

E: R

B-02

-002

HARDWAREOPTIONS



SPE

CIF

ICA

TIO

NS

Roller Blind Wire Guide

The Roller Blind Wire Guide is designed for perpendicular opening windows with a maximum of 20 degrees incline from vertical. The side wires provide stability and control of the blind when lowered or raised and can be fitted to both single and double Roller blinds.

• Suitable for perpendicular windows with a maximum of 20 degrees incline from vertical. • Suitable for Single and Double Roller blinds. • Wire is stainless steel 1.5mm (7x7 ASIS T316) which passes through stainless steel eye

bolts connected to the bottom rail. • The wire is tensioned by stainless steel top and bottom wire tensioners. • Bottom rails are either round or rectangular. The rectangular bottom rail has a standard

Soft Touch feature. • Bottom rails are available in White, Ivory, Chinchilla, Silver Pearl, Bronze, Anthricite, Black

or Anodised with Polypropylene end caps in: Black, White.

Key Numbers

1. Stainless Steel Top and Bottom Wire Tensioner

2. Powder Coated Steel Bracket3. Bracket Cover Plate4. Stainless Wire 1.5mm (7x7 ASIS T316)5. Control Chain6. Stainless Steel Eye Bolts7. Soft Touch8. Aluminium Bottom Rail9. Roller Tube

1

3

6

4

1

78

54

1

1

2

9

ISSU

E: R

B-03

-002

HARDWAREOPTIONS

SPE

CIF

ICA

TIO

NS



Blocco Roller SystemProduct OverviewBrand new to our stable of products is our Blocco Roller System. For the first time in New Zealand we can now offer this exclusive blackout blind which incorporates a head cassette containing the roller mechanism, side channels and a bottom channel to house the bottom rail, all of which are designed to eliminate light entering the room. The finished system is refined, compact and aesthetically very pleasing but most of all provides a complete solution where a room blackout is required. The system can be operated manually by a control chain or motorized with remote control or via a building management system. Blocco is constructed with our standard RollEase® Skyline clutches and the cassette, side and bottom channels are available in black, white or anodised with other special powder coated colours on request.

ApplicationsBlocco Roller system is the perfect solution when a blackout is required in commercial environments such as schools, hotels, hospitals and residential applications such as home theatre rooms and bedrooms.

Key Features• 100% light blocking design, with fully overlapping aluminium joins• Full wrap-around aluminium design, including bottom channel• Funnel-guides encapsulate fabric into the side channels• Modern square line appearance, with bevelled edges • Simple notching of the cassette profile for the chain to exit • Patent pending corner blocks for ease of assembly, with no light passing through

Operation• Manual - The control chain for the RollEase® clutch system is supplied with either a plastic beaded chain

with polyester cord or nickel plated steel chain. Both options are looped inside a Control Chain Weight. The plastic beaded chain contains no risk of corrosion and runs more quietly when blind is raised or lowered. Plastic beaded chain is available in 3 colours - white, grey or black. For a Chain-Stop operation, this is supplied without a control chain weight. Length of chain must be more than 2/3 drop of the window.

• Motorisation - Can be automated via Somfy’s range of Sonesse motors. These ultra-quiet motors set the standard for internal blind automation. Somfy’s wide range of control options includes hand held radio remote control, timers, weather sensors or a full building management system. Window Treatments NZ Ltd is an Authorised Somfy Automation Specialist.

ISSU

E: R

B-03

-002

Technical Data FinishThe Blocco aluminium cassette profile, side & bottom channels comes in black, white or anodised. Optional powder coated colours are available on request.

Fixing BracketsFace Fix (outside window frame) or Top Fix (inside window frame). Snap-in Light Guard End Covers are not required for Top Fixing. Bracket Specifications: HRPO 16 Gage (.0598). Thickness of material 1.6 [ 0.060 in]. Brackets are zinc plated and powder coated to required colour. No option for anodised.

95

86

21

50

50

DIM

. "A"

DIM. "B"

HARDWAREOPTIONS



SPE

CIF

ICA

TIO

NS

Maximum Cassette Size and Fabric Type

ISSU

E: R

B-04

-002

Single Cassette 2 Multi-Link Cassettes with two controls

of

Drg.No.Scale:

Drn:

Ch'kd:

Appd:

Date:

Date:

Date:

Rev.SheetREV. DATECHANGE BY

Melbourne -

A3

V206-X80-25012

A1 1 BLINDWARE PTY LTDWINDOW COVERING SYSTEM

M.KUMAR

30/04/2014

NO LIGHT SQUARE FASCIA - 3" x 31/2"SINGLE CASSETTE1:2

MUKESH KUMARINDUSTRIAL DESIGN SERVICES

AustraliaEmail : [email protected] PH : 0423 850 877

A ISSUED FOR REVIEW M.K 30.04.14

of

Drg.No.Scale:

Drn:

Ch'kd:

Appd:

Date:

Date:

Date:


Melbourne -

A3

V206-X80-25014


M.KUMAR

1/05/2014

NO LIGHT SQUARE FASCIA - 3" x 31/2"MULTI LINK-CASSETTES WITHIN ( ONE FASCIA & TWO CONTROLLER)1:3




of

Drg.No.Scale:

Drn:

Ch'kd:

Appd:

Date:

Date:

Date:


Melbourne -

A3

V206-X80-25013


M.KUMAR

1/05/2014

NO LIGHT SQUARE FASCIA - 3" x 31/2"MULTI LINK-CASSETTES WITHIN ( ONE FASCIA & ONE CONTROLLER)0.29:1




3 Multi-Link Cassettes with one control

1

11

1

Type No. of Fabric Colours Maximum Width Maximum DropSingle Cassette 3.0m 2 Multi-Link Cassettes with two controls 5.5m 3 Multi-Link Cassettes with one control 5.5m 4 Multi-Link Cassettes with two controls 5.5m

Blocco Single Unit

22

1.2

10 12 8 7

1110987

3 5

2.2

416

16

2.1 2.1

2.2 1616

4

2.1

1616

2.26

3

1.1 5

16

15 14

13

CEILING

43°

1.1

Cover Removal

Multi-Link Cassette within one FasciaThe cassette housing can be 5.5m wide but will require multiple linked blinds. Within one fascia, the maximum width of each individual unit will be determined by the tube deflection and room inside the cassette for the tube plus the fabric rolled up diameter. The side channel configuration for multi-link cassettes are duplicated in the centre of the blind, so there are 2 x side channels with one facing either direction to guide and cover the fabric. Bottom channels are the same, with the front profile still cut on a 45degree mitre.

Key Numbers and Description : Refer to Key for the Blocco Multi-Link Unit page

HARDWAREOPTIONS

SPE

CIF

ICA

TIO

NS



181

1

1

11

1

Blocco Multi-Link Units Individual control (One Fascia)Description: Two rollers linked together with an intermediate bracket. Allows for individual control.

ISSU

E: R

B-04

-002

Blocco Multi-Link Units (One Fascia)Description: Two rollers linked together with a universal bracket. Allows two blinds to be raised together.

Key Numbers and Description Colours Available 1. Fascia Cassette - Aluminium Anodised, White, Ivory, Silver Pearl, Bronze, Black (Optional colours are 1.1 Front Profile available on request) 1.2 Back Profile 2. Side and Bottom Channels - Aluminium Anodised, White, Ivory, Silver Pearl, Bronze, Black (Optional colours are 2.1 Front Profile available on request) 2.2 Back Profile 3. Fabric Funnel Insert - ABS Grey 4. Corner Block Insert (no light passing through) - ABS Grey 5. Fascia Cassette Slide Lock - ABS Grey 6. Chain Cut-out Cover (Universal) Grey, White, Black Nylon 6 -30% Glass filled 7. No light End Cover (Universal) - ABS White, Grey, Black 8. End Bracket 80mm (Universal) – Zinc plated, powder coated steel White, Black 9. RollEase® Pin End (Skyline) Spring Loaded – GEL lubricated PF30 White, Black 10. Tube Adapter, Skyline (38mm) – Nylon 30% glass filled White 11. Roller Blind Tube – Aluminium 12. RollEase® Clutch Controller(Skyline) - GF White, Black 13. Control Chain Options available • Plastic Beaded Chain with Polyester Cord - Thermally White, Grey, Black fused 0.175”Dia. plastic bead onto a heavy duty 0.065” Dia. Continuous nylon cord. • Nickel plated steel chain Nickel Plate • Various lengths available: 500mm, 750mm, 1m, 1.25m, 1.5m, 1.75m, 2m, 2.5m, 3m 14. Control Chain Weight - ABS -white/Grey part & PC - clear part White, Grey, Black 15. Bottom Bar weight - 12x3mm Aluminium flat bar 16. Lip Seal (Optional) protects fabric within Side and Bottom Channels - Polybond Woolpile 17. Link Bracket, Suit 80mm Blockout Cassette - Zinc plated 18. Retainer Unit, Suit Pin to Pin - Extruded Acetal (-N = Natural -B = Black) 19. Retainer Unit, Suit Tri Lobe Shaft - Extruded Acetal (-N = Natural -B = Black) Inners are produced from Natural Nylon 6 (-N = Natural -B = Black) 20. Link Bracket (Locking Plate), Suit 80mm Blockout Cassette – Zinc plated 21. Infinite Adjuster Kit - 30% Glass filled nylon 22. Fabric Roll Refer to roller fabric section Block-Out Ranges (Riviera, Valencia, Serengetti) Note: The Blocco cassette key feature design is a 100% blackout. When specifying top fix (inside of window frame) and if windows are not square, we apply a clear gap sealant between window frame and the side/bottom channels.

HARDWAREOPTIONS



SPE

CIF

ICA

TIO

NS

Fascia SpecificationFascias are made of extruded aluminium (alloy/hardness 6063/T5) with an average thickness of 1.5mm for flat profile and 1.75mm for round profile. Fascia Panels are finished with an electrostatically applied, baked on powder coating or clear natural anodised finish.

Square

Curved

Double

84mm

88mm

97mm

88m

m13

0mm

130mm

Fascia SystemThe roller blind head-rail is available with a curved or square no-notch Fascia for improved appearance and reduction in light gaps. The sleek design provides the most versatile technology available. Its durable elegance offers robust hardware with clean aesthetics and accommodates Single or Double Roller blinds. Square, Curved or Double Fascia systems accommodate manual or motorised options.

Double Roller Blind Fascia

ISSU

E: R

B-05

-002

HARDWAREOPTIONS

SPE

CIF

ICA

TIO

NS



Back Roll:

This is the most popular way of having the fabric hang off a roller blind tube. It keeps the fabric close to the window glass and also keeps the fabric close to the wall when Face Fix mounting the blinds.

Front Roll:

Ideal for the customer who does not want to see the roll at the top of their window. The fabric comes over the front of the roller blind tube so the tube is hidden from view. A front roll also provides more clearance from any obstructions such as window catches and handles.

Back Roll: Front Roll:Single Roller Universal Bracket for 38mm and 50mm tube

Back Roll: Front Roll:Double Roller Universal Standard Bracket for 38mm and 50mm tube

Back and Front Roll:

Double Roller Universal Vertical Bracket for 38mm and 50mm tubeBack and Front Roll:

ISSU

E: R

B-05

-002

HARDWAREFRONT AND BACK ROLL COMBINATIONS



SPE

CIF

ICA

TIO

NS

Rectangular Rounded

31m

m

70mm

100m

m

15mm 15mm 138mm15mm 15mm

150m

m

70mm15mm 15mm

100m

m

70mm15mm

88mm17

0mm

15mm 15mm

19mm

29m

m

Recessed Head Single Roller Recessed Head Double Roller

Recessed Head Double Roller Recessed Head Compact Double Roller

Bottom Rail

Diagram displays Front Roll Diagram displays Front Roll

Diagram displays Front Roll Diagram displays Front & Back Roll

ISSU

E: R

B-06

-002

HARDWARERECESS MEASUREMENTS

SPE

CIF

ICA

TIO

NS



Universal (Single Roller) BracketsSingle Roller Universal Brackets are ideal for most window frames as there is no need for a right and left style bracket. They are available in two sizes (38mm & 50mm projection) and suitable for both Top Fix and Face Fix installations. Matching Cover Plates come standard for Face Fix installations. Colours available: White, Black.

Universal Standard (Double Roller) BracketsDouble Roller Universal Standard Brackets offer greater flexibility when mounting two shades in one opening to create room darkening and ambient light control. They are available in two sizes (Standard 38mm and 50mm projection suits 38mm and 50mm tube). Brackets can be mounted to the ceiling or wall and there is no need for a right and left style bracket. The use of Double Roller Universal Brackets allows for proper alignment resulting in a better overall installation. When installation requires the double roller blind to be Face Fix, matching Cover Plates will come standard with this application. Colours available: White, Black.

Universal Vertical Compact (Double Roller) BracketsDouble Roller Universal Vertical Brackets are narrow, compact and reliable. Available for right and left mounts, they are great for narrow window frames and offer greater flexibility when mounting two shades in one opening to create room darkening and ambient light control. Double Roller Universal Vertical Brackets can only be mounted in a Top Fix application. The use of Double Roller Universal Brackets allows for proper alignment resulting in a better overall installation. Colours available: White, Black.

Bracket Cover PlatesBracket Cover Plates are standard for: Universal Single Roller 38mm & 50mm Face Fix, Universal Standard Double Roller 38mm & 50mm Face Fix. Colours available: White, Black. Please Note: The actual projection of the roller blind (tube & fabric) is variable depending on the drop of the window.Bracket covers slide over the bracket until snapped into position.

Bracket SpecificationBrackets are constructed of 0.06 inch thick nickel-plated, C1080/1010 cold rolled steel. The brackets are universal for example working on the clutch or pin end. Colours available: White, Black.

(Top Fix) CODE: STF61

Single Roller Universal Bracket 61mm projection (suits 38mm & 50mm tube)

(Face Fix) CODE: SFF61

Single Roller Universal Standard Bracket 61mm projection (suits 38mm & 50mm tube)

61m

m

38mm 18mm

61m

m

55mm 18mm

63m

m

6mm 63mm

63m

m

6mm 63mm

Cover Plate Universal

(Top Fix) CODE: STF72


72m

m

38mm 18mm

ISSU

E: R

B-06

-002

HARDWAREBRACKETS AND COVER PLATES



SPE

CIF

ICA

TIO

NS

D A T E : S H T n o ~ :

S C A L E S :

A 4

Monday, 21 January2013

1:4r o y a l . a r c h i t e c t s @ x t r a . c o . n zE -M A I L :TELEPHONE: 064 3 3799645 FACSMILIE: 064 3 3799 652atelier- 62 AVONSIDE DRIVE, CHRISTCHURCH, NEW ZEALANDR E G I S T E R E D A R C H I T E C T SROYAL ASSOCIATES L IM I TED

W I N D O W T R E A M E N T S

A.10.2Layout

63 mm

76 m

m

6 mm

63 mm

63 m

m

6 mm

102 mm10

2 m

m112 mm

120

mm

122 mm

122

mm

137 mm

8 mm

146

mm

8 mm

144

mm

51 mm 38 mm

61 m

m

38 mm

72 m

m

55 mm

74 m

m

55 mm

61 m

m

112 mm

120

mm

137 mm

146

mm

8 mm

8 mm

22

22

18 mm 18 mm 18 mm

18 mm

18 mm 63 mm

63 m

m

63 mm

76 m

m

b



94m

m

55mm 18mm

96m

m

6mm 63mm

96m

m

6mm 63mm

(Top and Face Fix) CODE: D102

Double Roller Universal Standard Bracket 102mm projection (suits 38mm tube)

102m

m

102mm 22mm

120m

m

8mm 112mm 8mm 112mm

(Top and Face Fix) CODE: D122

Double Roller Universal Standard Bracket 122mm projection (suits 38mm & 50mm tube)

122m

m

122mm 22mm

146m

m

8mm 137mm 8mm 137mm




120m

m

146m

m

(Top Fix) CODE: D144

Double Roller Universal Compact Bracket 144mm projection (suits 38mm & 50mm tube)

144m

m

51mm 18mm



74m

m

55mm 18mm76

mm

6mm 63mm

76m

m

6mm 63mm


D A T E : S H T n o ~ :

S C A L E S :

A 4

Monday, 21 January2013

1:4r o y a l . a r c h i t e c t s @ x t r a . c o . n zE -M A I L :TELEPHONE: 064 3 3799645 FACSMILIE: 064 3 3799 652atelier- 62 AVONSIDE DRIVE, CHRISTCHURCH, NEW ZEALANDR E G I S T E R E D A R C H I T E C T SROYAL ASSOCIATES L IM I TED

W I N D O W T R E A M E N T S

A.10.2Layout

63 mm

76 m

m

6 mm

63 mm

63 m

m

6 mm

102 mm

102

mm

112 mm

120

mm

122 mm

122

mm

137 mm

8 mm

146

mm

8 mm14

4 m

m

51 mm 38 mm

61 m

m

38 mm

72 m

m

55 mm

74 m

m

55 mm

61 m

m

112 mm

120

mm

137 mm

146

mm

8 mm

8 mm

22

22

18 mm 18 mm 18 mm

18 mm

18 mm 63 mm

63 m

m

63 mm

76 m

m

b

ISSU

E: R

B-07

-002

HARDWAREBRACKETS AND COVER PLATES

SPE

CIF

ICA

TIO

NS



KeyIntermediate BracketAllows blinds to operate independently

Multi Blind Universal BracketAllows up to 3 blinds to operate together

Spring AssistAllows blinds to be raised with less effort

Maximum Size Guidelines (based on 50mm tube size)

Description Controls Type

SINGLE CHAIN CONTROL ROLLER BLIND LEFT OR RIGHT 10

Description Controls & Spring Assist Type2 ROLLERS LINKED TOGETHER WITH A MULTI BLIND UNIVERSAL BRACKET & 1 SPRING ASSIST. LEFT OR RIGHT 12

3000mm

3000mm

Please Note : These measurements are guidelines only and Window Treatments can generally manufacture roller blinds outside these guidelines as required. For example if a blind has 7000mm drop, we may use a Galaxy series clutch without a spring assist fitted. Spring assists will provide lift assistance for heavier blinds but can limit the maximum drop achievable from normal clutch and spring systems. The Galaxy clutch features RollEase’s® patented planetary gear system and greatly reduces the chain pull force needed to lift heavy or long drop blinds.

Description Controls Type2 ROLLERS LINKED TOGETHER WITH AN INTERMEDIATE BRACKET. ALLOWS FOR INDIVIDUAL CONTROL. LEFT OR RIGHT on either blind 14

Single Roller

Multi (2) Rollers

Multi (3) Rollers

Multi (4) Rollers

6000mm

3000mm

3000mm

1500mm

9000mm

12000mm

ISSU

E: R

B-07

-002

HARDWARESINGLE ROLLER OPTIONS



SPE

CIF

ICA

TIO

NS

Description Controls Spring Assist Type3 ROLLERS LINKED TOGETHER WITH 1 INTERMEDIATE BRACKET, 1 MULTI BLIND UNIVERSAL BRACKET, 1 SPRING ASSIST & 2 CONTROLS. ALLOWS 2 BLINDS TO BE RAISED TOGETHER AND 1 INDEPENDENTLY.

LEFT OR RIGHT RIGHT on either blind

18

Description Controls Spring Assist Type3 ROLLERS LINKED TOGETHER WITH 1 INTERMEDIATE BRACKET, 1 MULTI BLIND UNIVERSAL BRACKET, 1 SPRING ASSIST & 2 CONTROLS. ALLOWS 2 BLINDS TO BE RAISED TOGETHER AND 1 INDEPENDENTLY.

LEFT OR RIGHT LEFT on either blind

20

Description Controls Spring Assist Type4 ROLLERS LINKED TOGETHER WITH 2 SPRING ASSIST, 2 MULTI BLIND UNIVERSAL BRACKETS, 1 INTERMEDIATE BRACKET. ALLOWS 2 SETS OF 2 BLINDS TO BE RAISED INDEPENDENTLY.

LEFT AND RIGHT LEFT OR RIGHT on either blind

22

Description Controls & Spring Assist Type3 ROLLERS LINKED TOGETHER WITH 2 MULTI BLIND UNIVERSAL BRACKETS, 1 CONTROL & 1 SPRING ASSIST. ALLOWS 3 BLINDS TO BE RAISED TOGETHER.

LEFT OR RIGHT 16

MotorisationMotorisation is available for all Roller Blind types 10, 12, 14, 16, 18, 20 and 22 as above. Spring assists are not required on Roller Blinds when motorisation has been selected.

ISSU

E: R

B-08

-002

HARDWARESINGLE ROLLER OPTIONS

SPE

CIF

ICA

TIO

NS




DOUBLE ROLLER BLINDS WITH CONTROLS AT OPPOSITE ENDS. LEFT AND RIGHT 24

Description Controls & Spring Assist Type2 DOUBLE ROLLER BLINDS LINKED TOGETHER WITH A DOUBLE MULTI BLIND UNIVERSAL BRACKET & 2 SPRING ASSIST. CONTROLS AT OPPOSITE ENDS WITH SPRING ASSIST.

LEFT AND RIGHT 28


DOUBLE ROLLER BLINDS WITH CONTROLS AT SAME END. LEFT OR RIGHT 26

Description Controls & Spring Assist Type2 DOUBLE ROLLER BLINDS LINKED TOGETHER WITH A DOUBLE MULTI BLIND UNIVERSAL BRACKET & 2 SPRING ASSIST. CONTROLS AT SAME END AS SPRING ASSIST.

LEFT OR RIGHT 30




Description Controls Type2 DOUBLE ROLLER BLINDS LINKED TOGETHER WITH A DOUBLE INTERMEDIATE BRACKET, 2 CONTROLS AT EACH END. ALLOWS INDEPENDENT CONTROL OF EACH BLIND.

LEFT AND RIGHT on either blind 32

ISSU

E: R

B-08

-002

HARDWAREDOUBLE ROLLER OPTIONS



SPE

CIF

ICA

TIO

NS

Description Controls & Spring Assist Type3 DOUBLE ROLLER BLINDS LINKED TOGETHER WITH 2 DOUBLE MULTI BLIND UNIVERSAL BRACKETS & 2 SPRING ASSIST. CONTROLS AT OPPOSITE ENDS WITH SPRING ASSIST. ALLOWS 3 BLINDS TO BE RAISED TOGETHER.

LEFT AND RIGHT 34

Description Controls & Spring Assist Type3 DOUBLE ROLLER BLINDS LINKED TOGETHER WITH 2 DOUBLE MULTI BLIND UNIVERSAL BRACKETS & 2 SPRING ASSIST. CONTROLS AT SAME END WITH SPRING ASSIST. ALLOWS 3 BLINDS TO BE RAISED TOGETHER.

LEFT OR RIGHT 36

Description Controls Spring Assist Type3 DOUBLE ROLLER BLINDS LINKED TOGETHER WITH 1 INTERMEDIATE BRACKET, 1 MULTI BLIND UNIVERSAL BRACKET, 2 SPRING ASSIST & 2 CONTROLS. ALLOWS 2 DOUBLE BLINDS TO OPERATE TOGETHER AND 1 INDEPENDENTLY.

LEFT OR RIGHT LEFT on either blind

38

Description Controls Spring Assist Type3 DOUBLE ROLLER BLINDS LINKED TOGETHER WITH 1 INTERMEDIATE BRACKET, 1 MULTI BLIND UNIVERSAL BRACKET, 2 SPRING ASSIST & 2 CONTROLS. ALLOWS 2 DOUBLE BLINDS TO OPERATE TOGETHER AND 1 INDEPENDENTLY.

LEFT OR RIGHT RIGHT on either blind

40

ISSU

E: R

B-09

-002

MotorisationMotorisation is available for all Roller Blind types 24, 26, 28, 30, 32, 34, 36, 38 and 40 as above. Spring assists are not required on Roller Blinds when motorisation has been selected.

HARDWAREDOUBLE ROLLER OPTIONS

SPE

CIF

ICA

TIO

NS






Description Controls Spring Assist

SINGLE CHAIN CONTROL ROLLER BLIND LEFT OR RIGHT

2 ROLLERS LINKED TOGETHER WITH A MULTI BLIND UNIVERSAL BRACKET & 1 SPRING ASSIST.

LEFT OR RIGHT

2 ROLLERS LINKED TOGETHER WITH AN INTERMEDIATE BRACKET. ALLOWS FOR INDIVIDUAL CONTROL.

LEFT OR RIGHT on either blind

3 ROLLERS LINKED TOGETHER WITH 2 MULTI BLIND UNIVERSAL BRACKETS, 1 CONTROL & 1 SPRING ASSIST. ALLOWS 3 BLINDS TO BE RAISED TOGETHER.

LEFT OR RIGHT LEFT OR RIGHT

3 ROLLERS LINKED TOGETHER WITH 1 INTERMEDIATE BRACKET, 1 MULTI BLIND UNIVERSAL BRACKET, 1 SPRING ASSIST & 2 CONTROLS. ALLOWS 2 BLINDS TO BE RAISED TOGETHER AND 1 INDEPENDENTLY.

LEFT OR RIGHT on either blind RIGHT

3 ROLLERS LINKED TOGETHER WITH 1 INTERMEDIATE BRACKET, 1 MULTI BLIND UNIVERSAL BRACKET, 1 SPRING ASSIST & 2 CONTROLS. ALLOWS 2 BLINDS TO BE RAISED TOGETHER AND 1 INDEPENDENTLY.

LEFT OR RIGHT on either blind LEFT

4 ROLLERS LINKED TOGETHER WITH 2 SPRING ASSIST, 2 MULTI BLIND UNIVERSAL BRACKETS, 1 INTERMEDIATE BRACKET. ALLOWS 2 SETS OF 2 BLINDS TO BE RAISED INDEPENDENTLY.

LEFT AND RIGHT on either blind LEFT OR RIGHT

16mm 12mm

16mm 12mm19mm

16mm 16mm

16mm 19mm19mm 12mm

16mm 19mm 16mm

16mm 19mm 16mm

16mm 19mm 19mm 16mm

20mm

20mm

20mm

20mm

Please Note: The light gap measurements are nominal and are based on 50mm tube. Light gap measurements for 38mm tube are nominally similar to 50mm and can be confirmed on request.

ISSU

E: R

B-09

-002

LIGHT GAPSMANUAL OPERATIONS 50MM TUBE



SPE

CIF

ICA

TIO

NS



Description

SINGLE ROLLER BLIND (1 motor required)

2 ROLLERS LINKED TOGETHER WITH A MULTI BLIND UNIVERSAL BRACKET (1 motor required).

2 ROLLERS LINKED TOGETHER WITH AN INTERMEDIATE BRACKET. ALLOWS FOR INDIVIDUAL CONTROL (2 motors required).

3 ROLLERS LINKED TOGETHER WITH 2 MULTI BLIND UNIVERSAL BRACKETS. ALLOWS 3 BLINDS TO BE RAISED TOGETHER (1 motor required).

3 ROLLERS LINKED TOGETHER WITH 1 INTERMEDIATE BRACKET, 1 MULTI BLIND UNIVERSAL BRACKET. ALLOWS 2 BLINDS TO BE RAISED TOGETHER AND 1 INDEPENDENTLY (2 motors required).

3 ROLLERS LINKED TOGETHER WITH 1 INTERMEDIATE BRACKET, 1 MULTI BLIND UNIVERSAL BRACKET. ALLOWS 2 BLINDS TO BE RAISED TOGETHER AND 1 INDEPENDENTLY (2 motors required).

4 ROLLERS LINKED TOGETHER WITH 2 MULTI BLIND UNIVERSAL BRACKETS, 1 INTERMEDIATE BRACKET. ALLOWS 2 SETS OF 2 BLINDS TO BE RAISED INDEPENDENTLY (2 motors required).

24mm 12mm

24mm 12mm19mm

24mm 24mm

24mm 19mm19mm 12mm

24mm 19mm 24mm

24mm 19mm 24mm

24mm 19mm 19mm 24mm

Please Note: The light gap measurements are nominal and are based on 50mm tube.

24mm

24mm

24mm

24mm

ISSU

E: R

B-10

-002

LIGHT GAPSMOTORISED 50MM TUBE

SPE

CIF

ICA

TIO

NS



Introduction to Fabric

Fabric Overview:The range of roller blind fabrics offers endless opportunities when used in commercial or domestic internal applications. We have various fabrics which comprise of intelligent energy saving screen fabrics, ecologically friendly, fire retardant, PVC free, mould and mildew resistant, light filtering to block-out fabrics.

ISSU

E: R

B-10

-002

INTRODUCTION TO FABRIC

Documents

ROLLER BLINDS - Quattro Shading · • Suitable for perpendicular windows with a maximum of 20 degrees incline from vertical. • Suitable for Single and Double Roller blinds