NETWORKS

www.shyamnetworks.com

RM24/58P2P and P2MP Radios

Quick Start Guide

For advanced settings and more detailed information, download the user

manual from www.shyamnetworks.com.

Package Contents

RM24/58 1Mast/Wall Mounting Kit 1Outdoor Ethernet Cable (Optional) 1External Antenna (Optional) 1PoE Injector 1Quick Start Guide 1Shyam Transmission System Management Software CD 1

NETWORKS

2

RM24/58

Available Models

1. Hardware Overview

MODEL DESCRIPTION

Point to Point Radio - TDMA (Outdoor) Link

RM-1C-18M-19-24 2.4 GHz, 18 Mbps with integrated 19 dBi antenna

RM-1C-18M-E-24 2.4 GHz, 18 Mbps with external antenna

RM-1C-50M-19-24 2.4 GHz, 50 Mbps with integrated 19 dBi antenna

RM-1C-50M-E-24 2.4 GHz, 50 Mbps with external antenna

RM-1C-100M-19-24 2.4 GHz, 100 Mbps with integrated 19 dBi antenna

RM-1C-100M-E-24 2.4 GHz, 100 Mbps with external antenna

RM-1C-18M-23-58 5.8 GHz, 18 Mbps with integrated 23 dBi antenna

RM-1C-18M-E-58 5.8 GHz, 18 Mbps with external antenna

RM-1C-50M-23-58 5.8 GHz, 50 Mbps with integrated 23 dBi antenna

RM-1C-50M-E-58 5.8 GHz, 50 Mbps with external antenna

RM-1C-100M-23-58 5.8 GHz, 100 Mbps with integrated 23 dBi antenna

RM-1C-100M-E-58 5.8 GHz, 100 Mbps with external antenna

LAN Port

RM-1C-18M-19-24

Antenna Port

LAN Port

Power LED

RM-1C-18M-E-24

NETWORKS

3

RM24/58

INTERFACE DESCRIPTION

Antennas Integrated or external antenna depending on the model.

LAN Port One LAN port 10/100/1000 Base-T interface with auto-negotiation.

Interface Description

Caution and Warnings

• Internal settings, adjustment, maintenance, and repairs should be performed only by

a skilled technician who is aware of the hazards involved.

• Do not tightly secure RM24/58 to its mounting brackets until the alignment process

of the antenna is complete.

• Check that there are no direct obstructions or interferences in front of RM24/58

when installing it.

• Do not stand in front of a connected RM24/58 as it requires clear line-of-sight (LOS).

• Make sure that both master and slave RM24/58 are assigned different IP addresses

before they are installed.

MODEL DESCRIPTION

Point to Multi Point Base Station and Subscribers - TDMA (Outdoor)

RPMP-1C-18M-E-24 2.4 GHz, 18 Mbps

RPMP-1C-18M-E-58 5.8 GHz, 18 Mbps

RPMP-1C-50M-E-24 2.4 GHz, 50 Mbps

RPMP-1C-50M-E-58 5.8 GHz, 50 Mbps

RPMP-1C-100M-E-24 2.4 GHz, 100 Mbps

RPMP-1C-100M-E-58 5.8 GHz, 100 Mbps

NETWORKS

4

RM24/58

2. Installing RM24/58

Additional Hardware

• RJ-45 crimp tool (if pre-assembled cable is not used)• Grounding cable• 13 mm or ½½ socket spanner• Ethernet cable - outdoor class, CAT-5e, and 4 twisted pairs• Cable ties• Computer/laptop running Windows XP/Windows 7

Installation Sequence

Mount RM24/58

STEP 1 Assemble RM24/58 unit onto the mast.STEP 2 Connect the ground cable to the chassis point on RM24/58.STEP 3 Attach cable from RM24/58 to the RJ-45 connector.STEP 4 Secure the cables to the mast or brackets using UV-rated cable ties.STEP 5 Repeat the procedure to mount the other RM24/58 at the slave site.

Mount RM24/58

Ground RM24/58

Align Master and Slave RM24/58

Connect RM24/58 to PoE Injector

Supply Power to

PoE Injector

PoE Adapter4-Port Switch

Integrated Antenna

NETWORKS

5

RM24/58

Ground RM24/58STEP 1 Crimp the grounding lug at both the ends on the earthing cable.STEP 2 Connect and tighten one end of the earthing cable to RM24/58.STEP 3 Connect other end of the earthing cable to the earth pit on the ground.iNote: Ensure that ground earthing is separated from power earthing.

Connect RM24/58 to PoE InjectorSTEP 1 Route the cable from RM24/58 into the building where PoE injector is placed.STEP 2 Secure the cable along its path.STEP 3 Connect the cable from RM24/58 to the appropriate RJ-45 connector on the PoE injector.

Supply Power to PoE InjectorSTEP 1 Connect the PoE adapter to the main electrical supply and the power cord plugged into the socket of the adapter.STEP 2 Turn on the power supply. RM24/58 starts receiving power through the PoE adapter.

Align Master and Slave RM24/58STEP 1 Turn on the power supply of the PoE injector at both the sites.STEP 2 Align master RM24/58 in the direction of slave RM24/58.STEP 3 Turn slave RM24/58 towards master site, listening to the beep sequence until optimal alignment is achieved.iNote: Frequent beeps indicate better signal strength. Higher signal strength has lower pause time in between the beeps. Frequencyofbeepconfirmsthelinkquality.Thesignalstrengthimproveswith the increase in the beep frequency. After approximately 40 seconds, the slave RM24/58 beeper starts beeping which indicates a normal operation.

STEP 4 Tightly secure slave RM24/58 onto the mast/wall. STEP 5 Repeat the same procedure at the master site.

Congratulations! The installation of RM24/58 is complete.

Beeper Sequence = On = Off

Description

Indicates a good signal

Indicates a weak signal

No air link

NETWORKS

6

RM24/58

3. Configuring RM24/58

STEP 1 Install the Shyam Transmission System Management software on the system,

which on successful installation creates the Shyam Transmission System icon on

the desktop.

STEP 2 Connect the system to the LAN.

STEP 3 Double-click the Shyam Transmission System icon on the desktop or click

Start | Programs | Shyam Transmission System.

STEP 4 Enter username and password as admin.

STEP 5 Connect RM24/58 either by specifying the IP addresses or enabling the

auto-discovery option.

On successful connection, the Shyam Transmission System window appears.

Please refer to “RM-24/58 Installation and Configuration Guide” for more details.

NETWORKS

7

RM24/58

4. Quick Troubleshooting

PROBLEM PROBABLE REASON RESOLUTION

No beep sound. There is no signal. •Ensure that cable at RM24/58 is properly connected.

•Check the connectivity between the external antenna and RM24/58.

•Check master and slave RM24/58 alignment.

•After setting to factory defaults, check that both master and slave sites have same SSID and pass-phrase for the radio link to work.

Beep sound has long pauses in between.

The signal is weak. •Check master and slave RM24/58 alignment.

•Check that the alignment beeps give the best signal beeper sequence.

NETWORKS

8

RM24/58

109.00021.00

SN/QS/RM24,58/06/11/R2.1

Warranty

This warranty is valid upto 12 months from the date of purchase.

Any manufacturing defect will be repaired by the company free of charge within the period of

warranty subject to the following conditions:

1. Thiswarrantycardmustbedulyfilledin,stamped&signedbythedealer.Thecardandtherelevantcashmemomustbepreserved&producedalongwiththedefectiveunit.

2. Once the defective unit is repaired during the said warranty period, the warranty shall thereafter

continue only for the unexpired period to the original warranty.

3. This warranty is not valid in case of

• Damage resulting from accidents, mishandling, negligence, tampering, unauthorized repair,

failuretofollowinstructions,lightning,fireandactofGod.

• Items not purchased from Authorized Dealers of the Company.

• Batteries (including rechargeable).

• Damage to the tamper proof seal.

• Adaptors (wherever applicable), where the Warranty is valid only up to 6 months from the date

of purchase of the product.

4. In case of a problem with your unit, please contact Customer Care. In the event that you are

advised to send and collect the unit from the Service Center of the Company – the same will be

done at your expense.

5. While Company or its Authorized Service Dealer will make every effort to carry out repairs under

this warranty as soon as possible, it is expressly made clear that the company shall not be held

liable for any direct or indirect loss to user due to delay in providing this service.

6. This warranty excludes every condition/warranty/liability not expressly set out therein.

7. Claims, if any to this warranty shall be subject to the courts having jurisdiction in Delhi, India.

Product ______________________________________________________________________

Model No. _______________________________ Serial No. ___________________________

Dealer’s Stamp & Signature Customer Care, Shyam Networks (A Division of Vihaan Networks Ltd.) 21-B, Sec-18, Udyog Vihar, Gurgaon-122015Haryana, India

Email: customer.care@vnl.inAll India Helpline No. - +91 124 309 2000 Ext. 2009, +91 9873573710

Manufactured by Vihaan Networks Ltd. Gurgaon, Haryana, India