Upload
tuan-tocdai
View
230
Download
0
Embed Size (px)
Citation preview
8/12/2019 Repeater Installation and Commissioning
1/34
!"#"$%"& ()*%$++$,-) . /-001**1-)1)2
8/12/2019 Repeater Installation and Commissioning
2/34
PowerPort
Input Port Output Port
MS
BS
Donor
AntennaCoverage
Antenna
Monitor
Port
Wi rel essRepeater
!"#"$%"& /-))"3,-)
8/12/2019 Repeater Installation and Commissioning
3/34
/-001**1-)1)2 !"#"$%"&
ConnectSerialCable:
Openthecabinet,connectRS232serialinterfaceofrepeatertoRS232serialinterfaceofportable
computerwiththeRS232cable
thatfitouttherepeater,andthenwecancommissiontherepeater
locally.
Remote Monitoring
Local OMT
ConnectWirelessModem:
InsertSIMcardinsideslotholder,connectthedefault
omni-antennaandmonitoring
center,getpowersupplytothemodem.
8/12/2019 Repeater Installation and Commissioning
4/34
456 $)7 4589:6
DOS:
1. Check carefully whether connection of RF signal is correct.2. Check the input power supply. Make sure voltage of power supply is in therange of rated working voltage of the repeater.3. Check antenna rack, feed cable and the host is grounded. Groundingimpedance shall be 5ohm.4. Check the echo loss of the antenna and feed system. Voltage StandingWave Ratio VSWR) < 1.5.5. The build and pole must be lightning proof.6. Entrance wire of power supply must pass lightning switch.7. Antenna and cable must pass lightning switch
8/12/2019 Repeater Installation and Commissioning
5/34
/-);2
8/12/2019 Repeater Installation and Commissioning
6/34
6"% /-00=-7"0 3?"3@
:
1.SetCommunication/Localcheck
2.EstablishingRemoteConnection3.Createanewrepeater4.Set Remote Communication Setup
Note:Usually,serialportofthecomputersdefaultsettingisCOM
1.Forlaptopwhichdonthaveserialport,havetouseUSB-Serial
conversioncable.AndtheCOMportwillnotbeCOM5orCOM6
etc.
8/12/2019 Repeater Installation and Commissioning
7/34
A*%$B+1*?1)2 !"0-%" /-))"3,-)
1.Connectawirelessmodemtothecomputerofcontrolcenter.2.LogintothemainscreenoftheOMT.ChooseSMS
3. Create a new device
4. Set Remote Communication Setup.5. Click Get and then Search to confirm whether Remote Communication Parameters has been set
successfully.6. Connect the BTS port with donor antenna cable, before remote communication
7. If Short Message is set during Remote Communication Setup setting, click Start.
SMSMode
8/12/2019 Repeater Installation and Commissioning
8/34
4"C13" /-);2ClickGetMOIDFrom
Device->
BuildMOIDlistautomatic
8/12/2019 Repeater Installation and Commissioning
9/34
4"C13" /-);2MOIDListConfig->Theusertoconfigurethe
equipmentneededformonitoringparameters
6.Openthecom.port->ChooseDeviceType->ClickUserConfiguration
8/12/2019 Repeater Installation and Commissioning
10/34
4"C13" /-);2
8/12/2019 Repeater Installation and Commissioning
11/34
D$
8/12/2019 Repeater Installation and Commissioning
12/34
G#2&$7"
:
UpgradeFirmwareByLocalMode:
1.Confirmthelocalcommunicationisokay
2.ClickTools->UpgradeFirmware->UpgradeFirmwareinterface
3.ClickbuttonOpenFile->Selectupgradeapplicationprogramfile(.hex)->
ClickOK
4.ClickStart->StartobtainFirmwareVersion
5.DisplayErasingflashpleasewait...
6.DisplayUpgradeinprogress...,startudgrade
7.Upgradefinished,displayUpgradeSucceed!->ClickOK,upgradesuccessful!
8.SearchDeviceParameters->Checktheversion
8/12/2019 Repeater Installation and Commissioning
13/34
G#2&$7"
:
UpgradeMemmapbyLocalMode:
1.Confirmthelocalcommunicationisokay
2.ClickTools->UpgradeMemmap->UpgradeMemmapinterface
3.ClickbuttonOpenFile->Selectupgradeapplicationprogramfile(.hex)->ClickOK
4.ClickStart->StartobtainMemmapVersion
5.DisplayErasingflash...
6.DisplayUpgradeinprogress...,startupgrade
7.Upgradefinished,displayUpgradeSucceed!->ClickOK,upgradesuccessful!
8.SearchDeviceParameters->Checktheversion
8/12/2019 Repeater Installation and Commissioning
14/34
G*"H
8/12/2019 Repeater Installation and Commissioning
15/34
61%" :&-
8/12/2019 Repeater Installation and Commissioning
16/34
5#"&$,-) . =-)1%-&1)2
Remote MonitoringLocal OMT
Operation & Maintenance terminal
(OMT) interact with the
Repeater to set and lookup its
status and RF parameters. Itcan display alarms real-time.
OMT can set local connection,wireless data connection or
SMS connection with the
device for operation and
maintenance at any time, or atany location.
8/12/2019 Repeater Installation and Commissioning
17/34
5#"&$,-) . =-)1%-&1)2
8/12/2019 Repeater Installation and Commissioning
18/34
5#"&$,-) . =-)1%-&1)2
8/12/2019 Repeater Installation and Commissioning
19/34
5#"&$,-) . =-)1%-&1)2
Database Management
8/12/2019 Repeater Installation and Commissioning
20/34
8/12/2019 Repeater Installation and Commissioning
21/34
J-M"& 6
8/12/2019 Repeater Installation and Commissioning
22/34
K+$&0 N$)7+"
Repeater Alarm: Master Power FailureAlarm Imitation: Shut down repeater power supply AC 220V
Master Power Failure
Alarm Reason : No AC 220V Power SupplySolution check and restore the AC power supply
Reason and Solution
8/12/2019 Repeater Installation and Commissioning
23/34
Power Module Alarm
Alarm Reason : 1.AC 220V Power Supply Modules malfunctionSolution Replace the power module
Alarm Reason : 2.Ouput DC Voltage fluctuation is beyond 15% of
Voltage Rating
Solution: Disconnect all power cables to other modules and
connect to power module one by one to check the faulty module
and replace it
Master Alarm: Power Module AlarmAlarm Imitation: Shut down repeater power switch
Reason and Solution
K+$&0 N$)7+"
8/12/2019 Repeater Installation and Commissioning
24/34
Alarm clear or not
Power Module Alarm
Power Module
Failure
Green LED
on or off
Off
On
Not clear
Connect the power cable
between power module
and GSM module
Alarm clear or not
clear
Not clearGSM Module
Failure
DCS Module
Failure
clear
Replace the
Power module
Replace the
GSM module
Replace the
DCS module
Disconnect the power cable
between power module
and all other modules
Power Module Alarm
8/12/2019 Repeater Installation and Commissioning
25/34
Master Alarm: Low Battery Power Alarm
Low Battery Power Alarm
Alarm Reason I: failure of battery power of the monitoring boardSolution Replace the battery power
Reason and Solution
K+$&0 N$)7+"
8/12/2019 Repeater Installation and Commissioning
26/34
Repeater Alarm: Master/Slave Module CommunicationFailure Alarm Imitation: Disconnect the RS485 cable between
monitoring board and other modules
M/S Module Comm. Failure
Alarm Reason I: the RS485 cable between monitoring board and
other modules is broken
Solution replace the RS485 cable
Reason and Solution
Alarm Reason III: failure of the DCS integration moduleSolution check and replace the DCS integrationmodule
Alarm Reason II: failure of the GSM integration moduleSolution check and replace the GSM integration
module
K+$&0 N$)7+"
8/12/2019 Repeater Installation and Commissioning
27/34
Repeater Alarm: Over temp. AlarmAlarm Imitation: PA Temp Limit:85
PA Real Temp:40~60 Adjust the PA Temp Limit to the level of 90
Over Temp. Alarm
Alarm Reason I: ambient temperature is out of the tolerance of design.
Solution equip an overshadow canopy to avoid the high
temperature caused by the direct sunshine.
Reason and Solution
Alarm Reason II: the environmental condition is air-tighted, so the
heat can not be sent out fluently.
Solution move the repeater to a ventilated location
K+$&0 N$)7+"
8/12/2019 Repeater Installation and Commissioning
28/34
Repeater Alarm: Phase-locked Loop Unlock
PLL Unlock
Reason and Solution
Alarm Reason III: failure in the phase-locked module of DCS
integration module
Solution check and replace the DCS integration
module
Alarm Reason II: failure in the phase-locked module of GSMintegration module
Solution check and replace the GSM integration
module
K+$&0 N$)7+"
8/12/2019 Repeater Installation and Commissioning
29/34
Repeater Alarm: Downlink Over Input Power AlarmAlarm Imitation: Original repeater input power limit:-60~-30dBm
Set repeater over input power limit at the level of-60dBm
DL Over I/P Alarm
Alarm Reason I: set the DL Over I/P Limit too low
Solution set the DL Over I/P Limit to -30dBm again
Reason and Solution
Alarm Reason II: the signal which the donor antenna received is too strong.
Solution add the attenuator in the input port of repeater or change
the position of donor antenna to adjust the input power of repeater
K+$&0 N$)7+"
8/12/2019 Repeater Installation and Commissioning
30/34
DL Low I/P Alarm
Alarm Reason I: Set the DL Low I/P Limit too high
Solution Set the DL Low I/P Limit to -60dBm again
Reason and Solution
Alarm Reason II: the signal which the donor antenna received is too
weak.Solution Change the position of donor antenna and check the
feeder cable which connect to input port of repeater to
increase input power
Repeater Alarm: Downlink Low Input Power AlarmAlarm Imitation: Original repeater input power limit:-60~-30dBm
Set repeater low input power limit at the level of-30dBm
K+$&0 N$)7+"
8/12/2019 Repeater Installation and Commissioning
31/34
Repeater Alarm: Downlink Over Output Power AlarmAlarm Imitation: Original repeater output power limit:9~29dBm
for 27dB gain repeaterSet repeater over output power Limit at the level
of 9dBm
DL Over O/P Alarm
Alarm Reason I: Set the DL Over O/P Limit too low
Solution Set the DL Over O/P Limit to 29dBm
Reason and Solution
Alarm Reason II: failure in output of PA in repeater
Solution check and adjust the output of PA in repeater, if
there is
malfunction in PA, replace the integration module.
K+$&0 N$)7+"
8/12/2019 Repeater Installation and Commissioning
32/34
DL Low O/P Alarm
Repeater Alarm: Downlink Low Output Power AlarmAlarm Imitation: Original repeater output power limit:9~29dBm
for 27dB gain repeaterSet repeater low output power Limit at the level
of 29dBm
Alarm Reason I: Set the DL Low O/P Limit too high
Solution Set the DL Low O/P Limit to 9dBm
Reason and Solution
Alarm Reason II: failure in output of PA in repeater
Solution check and adjust the output of PA in repeater, if
there is
malfunction in PA, replace the integration module.
K+$&0 N$)7+"
8/12/2019 Repeater Installation and Commissioning
33/34
!"$*-)* =$L ()C-+C" =-7"0 1)1,$,-) H$1+
8/12/2019 Repeater Installation and Commissioning
34/34
!"$*-)* =$L ()C-+C" 8-% ")$B+" %?" $+$&0 8-% #&-#"& +101% 3-);2