Embed Size (px)
Citation preview
1. Connect the charger to the USB port on the headphones.2. Connect the USB on other end of the charger to any USB charging adapter or active computer USB port.- The LED indicator will turn solid red when charging- The LED indicator will turn solid blue when charging has completed
It takes 1.5-2 hours to charge the battery fully. The headphones perform best when fully charged. It’s recommended to charge the battery fully for the first time using.
Cipset: CSR BC8635Bluetooth Version: V4.1+EDRBluetooth Protocol：A2DP v1.2, AVRCP v1.4, HFP v1.6, HSP v1.2,DI v1.3Radio Frequency range: 2.402GHz～2.483GHzModulation Type: GFSKEffictive Distance: Up to 10 metersAudio Frequency Range: 20Hz～20KHzLoundspeaker Specification：￠11 real copper coilMIC：Silicon microphone -42±3dB/ 3.76x2.95x1.1mmBattery Capacity: Rechargeable polymer Li-Ion battery （100mAH） Charing Time: About 2 hoursCharing Voltage：DC 5VTalk Time: 6-8 hoursPlay Music：6-8 hoursStandby Time: Up to 250 hoursProduct Weight：22g
Charging
Specifications
Pairing
Pairing with Two Bluetooth Devices at the Same Time You can pair your headphones with two devices, but only one of them can play musicor make phone calls with the headphones at any time.
1. Follow the previous instructions in the “Pairing” section above to pair the headphones to your first devices.2. Turn off the Bluetooth function on your first device and follow the pairing instructions above again to pair the headphones to your second Bluetooth device.3.Then both the two Bluetooth devices have a connection record, turn on bluetooth function of the two devices, you will can connect the two Bluetooth devices at the same time.
When charging, long press MFB until the indicator red-solid and flashes blue for 3 times, it means that the factory settings have been restored, the headset will clear the pairing information.
1. Keep your Bluetooth device within 1 meter of the Bluetooth headphones when pairing.2. When the headphones are off, long press the Multifunction button for 5 seconds until the red and blue lights flash alternately, the headphones will enter pairing mode then.
3. Turn on the Bluetooth function on your Bluetooth device and search for available Bluetooth devices, select “A8”.4. If a password or PIN code is requested during pairing, enter “0000”.5. Once connected, the LED indicator will flash blue and you will hear a voice prompt “Your headset is connected” in the earphone.
Note:
Restoring the Factory Settings
4.1 Wireless Sports Headphones
A8
Function Operation (MFB means Multifunction Button)
Button Control
When off,long press the multifunction button for 3 secondsPower ON
When on,long press the multifunction button for 3 secondsPower OFF
Press the MFB once in audio modePlay/Pause
Press the volume + or - button onceVolume +/-
Long press the volume + or - buttonNext/Previous Track
When there is an incoming call, press the MFB onceAnswering Phone call
During a call, press the MFB onceEnd a Phone Call
Receiving incoming call, long press the MFBReject a Phone Call
Press the MFB twice to redial the latest phone numberNumber Redial
When connecting, long press the MFB for 1 second,hear the headphones issued a "beep" prompt then release to activate the phone voice assistant (Siri) function
SIRI Function
During a call, long press MFB for 1 second
When off,long press MFB until the LED indicator flashes red and blue
Transfer voice between headset and phone
Pairing Mode
LED Indication Status
LED Indicator
CharingRed - solid
Fully ChargedBlue - solid
Not paired with any deviceBlue and Red - Flashing
Paired with a deviceBlue - Flashes every 7s
Low BatteryRed - Flashing
How to Use
Please make sure the headphones get into "pairing" mode - if you just turn the headphones on to the point of it saying "Power On" and never hold the button in long enough to get the red and blue flashing lights, you won't be able to connect them.
Stereo BluetoothWireless Headphones
Carry Storage Pouch
SHUHUA
Wire Clip
Package Contents Product Overview
The volume-
The volume+
MFB key
LED
Microphones
USB Charger
R
Note:
Coated with nano waterproof material waterproof standard：
A: Please make sure the headphones are recharged and have enough power. Plug the headphones to a charger and check if the LED indicator becomes solid red.
Q: The headphones will not turn on.
A: 1) Make sure the headphones are turned on and the LED indicator is flashing blue and red. 2) Make sure the headphones and the Bluetooth devices are close to each other within 3 feet. 3) Turn off the headphones and the Bluetooth device, turn the headphones on again and restart the Bluetooth devices. Then retry the pairing method. 4) Restore the factory settings by following the instructions in the “Restoring the Factory Settings” section above. 5) Make sure your Bluetooth device supports A2DP.
Q: Pairing to a Bluetooth device doesn’t work.
A: 1) Recharge your headphones, the power may be too low. 2) Units are out of range (10 meters maximum). Bring units closer together. 3) Remove any object (electrical or magnetic) that may be interfering or blocking the signal between units.
Q: After pairing, the headphones disconnect or there is too much background noise.
A: 1) Please check if the headphones have connected with your Bluetooth device successfully. The LED indicator should flash blue every 6 seconds. 2) Make sure the volume is at an audible level on both the headphones and your Bluetooth device. 3) Make sure the Bluetooth device is playing music/audio. 4) Some cellphones do not have a complete Bluetooth function and stereo Bluetooth module that are required to listen to music. Please test whether this is the case by connecting the headphones with another cellphone. If you can Listen to music through the other cellphone, the headphones are functioning as they should.
Q: After pairing and connecting with my Bluetooth device, I can not listen tomusic/audio.
A: If the headphones have not been used for a long time, they may need to be charged. Leave the headphones on charge for about 30 minutes and the red light should come on again.
Q: The LED indicator does not show solid red when charging the headphones.
A: 1) If your computer has a Bluetooth function, simply turn it on and search for the headphones. 2) If your computer does not have a Bluetooth function, then you will need a wireless adapter in order to connect your computer to the headphones.
Q: How to use the headphones to listen to music on computer?
A: The headphones are coated with nano waterproof material. They will not be damaged by rain or even in the shower - but we strongly do not recommend using them in a pool.
Q: How is the waterproof level of the headphones?
A: 1) The charging cord is broken. Please try to use other charging cord to charge the headphones. 2) There might be something wrong with the battery. If it is kept too long time without using or charging, the capacity and the life of the battery will reduce.
Q: The headphones could not hold a charge anymore.
A: Most Bluetooth devices don’t require a password/PIN during pairing, but enter “0000” (four zeros) if asked.
Overcharging or keeping the headphones in a closed car or similar environmentfor long periods will reduce the capacity and the life of the It’s not recommend to charge the headphones overnight.
Q: The Bluetooth Device asks for a password/PIN while pairing
Suitable
Unsuitable
* Splashes* Rain or Snow* Showering* Incidental exposure to water of up to 1 meter for up to 30 minutes
* Swimming* Diving into water* Snorkeling or Scuba Diving* High-speed watersports
1. Although the headphones are equipped with necessary battery regulators, it is recommended not to use Quick/Fast Chargers which tend to over-charge the device and can reduce the lifespan of the battery substantially.2. Do not charge the headphones when they are wet due to sweat or other moisture.3. Wipe away any excess sweat or moisture before and during use, any prolonged exposure to sweat can corrode the liquipel coating and can penetrate through and damage internal components.4. Keep the headphones away from extreme heat and humidity. High heat will decrease the lifespan of the headphones and battery.5. The headphones should be charged at least once every 6 months.6. Clean with a soft cloth, damp with diluted soap water solution if necessary. Never use chemical cleaners.7. Do not drop the headphones on hard surfaces.8. Do not take the headphones apart.9. When not in use, power the headphones off and store in a cool, dry place.
Safety and Care
Warranty
Troubleshooting
We guarantee every product has undergone rigorous tests prior to shipping.We are so confident in the quality of our products that we offer a one year warrantyfrom the date of purchase.
Dear Customer,
Thank you so much for your order! We sincerely hope that you would be satisfied with our product and service. We’d appreciate if you couldleave us a five star comment on the feedback and review.
Email:[email protected]
Sincerely,SHUHUA Team
CriteriaArrived on Timeltem as Described
If you have any concern about our product and service, please do not hesitate to contact us via email.Thank you!
Customer Service
Average rating★★★★★★★★★★★★★★★
R
www.shuhuatech.com
