Embed Size (px)
Citation preview
Put your company on theCutting Edge
of concrete floor technology!
3
The Mini Screed™ C delivers the same results as our other walk-behind Laser Screeds® and gives your crews the ability to:
Laser Screed® projects that were previously to small
Laser Screed® on lightweight metal decks
Screed small jobs with laser accuracy
Screed at a lower cost than any other conventional method or product on the market today
The Mini Screed™ C is a small, yet powerful, self-propelled, walk-behind Laser Screed® that’s small enough to fit in the bed of a pickup, but large enough to tackle a wide range of jobs.
The Mini Screed™ C delivers outstanding performance slab-on-grade, below-grade, or on virtually any type of deck.
Introduction
4
Yesterday’s method of hand-screeding floors
5
Each model has it’s own unique applications
Today’s leading-edge technology of a Laser Screed® floor
6
Slab-on-Grade or Slab-on-Deck Projects
- Fibers
- Pulled Mesh
- Chaired Mesh
- Chaired Rebar
- Double Mat Rebar
- Post Tension
- Precast Topping
- Fluted Metal Deck
- Radiant Floor Heating
Applications
7
™
Quality difference between today’s screeding methods
8
Maneuverability
9
LIGHTWEIGHT, COMPACT DESIGN
Weight: 470 lbs Width: 32” outside of tires Head Width: 6’8” Height: 41” without masts Length: 72 ½”
10
No Wet-pads or Rails needed
Screeding with the Mini Screed™ C
11
Mini Screed™ C Features
Weight: 470 lbs. Height: 41” without masts Length: 72 ½” Width: 32” outside tires
30 ½” handle bars83 ½” head
AutomaticSelf Level Robin America
6 hp Gas Engine
High Float Tires (standard)Skinny Tires (optional)
Adjustable Weight
Distribution
Headlights
2 Lift PointsAutomatic
Operator Controls
SSR Laser Receiverswith internal
1/16 inch grade adjustment
Quick Disconnect Head
Pivoting6’ 8” VibratingScreed Head
Adjusts 6 times per secondto maintain grade
12
TIME RAISE / LOWERSWITCH
FORWARD / REVERSESWITCH
VIBRATORSWITCH
HEADLIFTSWITCH
QUICK PASSCONTROL
MANUAL RECIEVEROVERRIDE
HEADLIGHTSWITCH
Easy Operation
Operator Friendly - Fast Learning Curve
13
Mini C weight = 470 lbs Ground Pressure = 3.9 psi
Average weight = 190 lbs Ground Pressure size 11 boot = 2.2 psi
Man vs. Machine
Exerts less pressure on the surface then 2 men
14
Performs on Various Applications
15
Improve hourly productivity.
Faster finishing times.
Reduce overtime expenses.
Improve floor quality.
Improve concrete yields.
Notice immediate labor savings.
Reduce fatigue.
Retain key personnel.
Reduce workers compensation claims.
Costs less per month than one laborer.
Improve your competitive edge, win more bids.
Improve the image of your company.
Why consider purchasing a Mini Screed™ C
Faster…Faster…
Flatter…Flatter…
Fewer…Fewer…
Profitability…Profitability…
16
Mini Screed™ C $ 27,950
Spare Parts Kit & Manuals included
Initial On-Site Training included
Destination $ 800
$ 28,750
Options
Emergency Support Kit $ 1,918
Start-up Kit $ 3,171Includes: tripod, column clamp, lift harnesses, skinny tire assy, L-500 laser transmitter
All pricing is in US Funds and subject to change
$800 Destination is valid for the continental US only
Note: additional training trips $1,500 each if needed
PRICING
Monthly Payments* Start At
$ 547
with first & last down, 60 months, 10% buy out
17
OPTIONAL START-UP KIT:
LL-500 non-sloping Laser TransmitterTripodColumn Clamp Skinny Tires & Wheel Assy.Lift Harness
OPTIONAL SUPPORT KIT:
Control Box SSR Receiver CordLinear Actuator Assy.2 Plow Wings4 Plow Linkages8 Vibrator IsolatorsHydraulic FilterAir FilterClamp AssemblyMisc HardwareCarrying case
Standard and Optional Equipment
STANDARD SPARE PARTS KIT:
Owner’s ManualActuator cordEmergency CordRocker SwitchesSpare Pins (turnbuckle/removable head)Cotter PinsRing- SplitIsolators8mm Hex bit, T handleElement, Air filterCarrying caseGauge- Air Pressure DigitalFitting Grease M10 straight
18
15,000 sq. ft. Placement
1 – Finisher setting wet pads2 – Finishers using a straight edge3 – Laborers leveling concrete while screeding6 - Total manpower for the screeding process
Average 2,500 sq. ft. per hour
15,000 sq. ft. Placement
1 - Finisher using a Somero Mini Screed C2 - Laborers leveling concrete while screeding3 -Total manpower for the screeding process
Average 3,000 sq. ft. per hour
3 Man Savings with a Mini Screed™ C
Typical ManpowerConventional vs. Mini Screed™ C
19
15,000 sq. ft. Placement
3 - Finishers @ $40 per hr x 6 hr = $ 7203 - Laborers @ $30 per hr x 6 hr = $ 540
Conventional Labor Cost = $ 1,360
15,000 sq. ft. Placement
1 - Finisher @ $40 per hr x 5 hr = $ 2002 - Laborers @ $30 per hr x 5 hr = $ 300
Mini Screed™ C Labor Cost = $ 500
Average Non-Union Labor Savings = $860 per day
Average Non-Union Labor CostConventional vs. Mini Screed™ C
Yields a 460% Return On InvestmentAssuming 30 uses per year with an average labor rate of $35/hr, $604 per month in payments and operating expenses
20
Average Union Labor Savings = $1,062 per day
Average Union Labor CostConventional vs. Mini Screed™ C
15,000 sq. ft. Placement
3 - Finishers @ $54 per hr x 6 hr = $ 9723 - Laborers @ $45 per hr x 6hr = $ 810
Conventional Labor Cost = $ 1,782
15,000 sq. ft. Placement
1 - Finisher @ $54 per hr x 5 hr = $ 2702 - Laborers @ $45 per hr x 5 hr = $ 450
Mini Screed™ C Labor Cost = $ 720
Yields a 679% Return On InvestmentAssuming 30 uses per year with an average labor rate of $51/hr, $604 per month in payments and operating expenses
21
Combine the Mini-RakeMini-Rake™ with a Mini ScreedMini Screed™ CC and you will significantly increase
your labor savings and floor quality even more.
Extremely Productive Package!
23
Somero Mini Screed™ C
Increase Your Increase Your Competitive Competitive
Advantage in 2010!Advantage in 2010!
Greater Efficiency- Less money spent per square foot screeded- Operator and crew friendly
Increases Productivity- Screed more square feet per hour
Improves Quality- Improved FL numbers
Safer- Fewer injuries
Lowers Operating Costs- Fewer work comp claims- Less lost time- Lower insurance rates
Yields Greater Profitability- ROI’s of 300-800% or more
