Upload
others
View
4
Download
0
Embed Size (px)
Citation preview
Installation Instructions
PowerFlex® 700S and 700H Fan Inverter Upgrade Kit (Frame 10-11)
Introduction Use this document to upgrade the fan inverters on PowerFlex 700S or 700H frame 10 or frame 11 drives.
What this Kit Contains Verify that your kit contains the items listed in the following table. If your kit does not contain the correct items, contact your Allen-Bradley sales representative.
!ATTENTION: To avoid an electric shock hazard, ensure that all power to the drive has been removed before performing the following.
!ATTENTION: To avoid an electric shock hazard, verify that the voltage on the bus capacitors has discharged before performing any work on the drive. Measure the DC bus voltage at the DC+ & DC- terminals. The voltage must be zero.
!ATTENTION: HOT surfaces can cause severe burns. Do not touch the heatsink surface during operation of the drive. After disconnecting power allow time for cooling.
!ATTENTION: Hazard of permanent eye damage exists when using optical transmission equipment. This product emits intense light and invisible radiation. Do not look into fiber-optic ports or fiber-optic cable connectors.
!ATTENTION: This drive contains ESD (Electrostatic Discharge) sensitive parts and assemblies. Static control precautions are required when installing, testing, servicing or repairing this assembly. Component damage may result if ESD control procedures are not followed. If you are not familiar with static control procedures, reference A-B publication 8000-4.5.2, “Guarding Against Electrostatic Damage” or any other applicable ESD protection handbook.
Part No.
Quantity:
DescriptionFrame 10 Kit
Frame 11 Kit
FR10844 1 0 Left-hand Inverter ChassisFR10845 1 3 Right-hand Inverter Chassis133256 1 1 Disposable Static Discharge Wrist-strap
2 PowerFlex® 700S and 700H Fan Inverter Upgrade Kit (Frame 10-11)
What You Need to Do ❐ Step 1: Remove power from the drive.
❐ Step 2: Remove the covers from the power structure.
❐ Step 3: Prepare the power structure for inverter assembly removal.
❐ Step 4: Remove the old inverter assemblies from the drive.
❐ Step 5: Remove the inverters from the old assemblies.
❐ Step 6: Install the inverters on the new assemblies.
❐ Step 7: Install the new inverter assemblies and prepare the drive for use.
Step 1: Removing Power from the Drive
1. Turn off and lock out input power. Wait five minutes.
2. Verify that there is no voltage at the drive’s input power terminals.
3. Measure the DC bus voltage at the DC+ & DC- terminals on the Power Terminal Block. The voltage must be zero.
!ATTENTION: To avoid an electric shock hazard, verify that the voltage on the bus capacitors has discharged before performing any work on the drive. Measure the DC bus voltage at the DC+ & DC- terminals of the Power Terminal Block. The voltage must be zero.
Remove power before making or breaking cable connections. When you remove or insert a cable connector with power applied, an electrical arc may occur. An electrical arc can cause personal injury or property damage by:
• sending an erroneous signal to your system’s field devices, causing unintended machine motion
• causing an explosion in a hazardous environment
Electrical arcing causes excessive wear to contacts on both the module and its mating connector. Worn contacts may create electrical resistance.
L1 L2 L3
O
I
PowerFlex® 700S and 700H Fan Inverter Upgrade Kit (Frame 10-11) 3
Step 2: Removing Covers from the Power Structure
Moving Control Frame
Task DescriptionLoosen the T8 Torx-head screws, which secure the Control Frame to the drive enclosure (Remove screws on early frame 10 drives).
Swing the Control Frame out and away from the power structure.
A
B
B
Frame 10 Drive Shown
Frame 10 drives, from early production runs, have holes instead of slots for these screws. You must
completely remove the screws from these drives in order to swing-open the control frame.
orA
A
4 PowerFlex® 700S and 700H Fan Inverter Upgrade Kit (Frame 10-11)
Removing the Airflow Plate
Task DescriptionRemove the T8 Torx-head screws, which secure the airflow plate to the drive.
Slide the airflow plate off the drive.
A
B
A B
A
Frame 10 Drive Shown
PowerFlex® 700S and 700H Fan Inverter Upgrade Kit (Frame 10-11) 5
Removing the Protective Covers
Task DescriptionRemove the four M5 Pozi-drive screws, which secure the top and bottom protective covers to the main front protective cover, then remove the top and bottom protective covers.
Note: you only need to remove the top and bottom covers to gain access to the power terminals. You can remove the other covers without removing the top and bottom ones. Remove the four M5 Pozi-drive screws, which secure the main front protective cover to the drive, then remove the protective cover.
Remove side protective covers(Not necessary for Frame 11 Drives).
A
B
C
A
B
Frame 10 Drive Shown
A
A
A
B
B
B
C
Proper tightening torque for reassembly is 4 N-m (35 lb.-in.).
C
6 PowerFlex® 700S and 700H Fan Inverter Upgrade Kit (Frame 10-11)
Step 3: Preparing Power Structure for Inverter Assembly Removal
Preparing a Frame 10 Power Structure
Task DescriptionRemove the cable-ties that secure the cables with orange insulation (on both left-hand and right-hand sides). This will allow you to move the cables while removing the inverter assemblies.
A
A
A A
Left-handSideView
Right-hand Inverter
Left-handInverter
Front Viewon Left-hand Side
PowerFlex® 700S and 700H Fan Inverter Upgrade Kit (Frame 10-11) 7
Preparing a Frame 11 Power Structure
Task DescriptionUsing a 17 mm wrench, loosen the three connections to the output terminal next to the inverter assembly. Proper tightening torque for reassembly is 29 ft - lb.Cut cable-tie, which secures the cable to the capacitor and disconnect that cable.
Disconnect the four wires from the fuse block on the center inverter assembly.
A
B
C
A A A
B
CC
CC
Front Viewof Left-hand Side
Front Viewof Center of Power Structure
Right-hand Inverter
Left-handInverter
CenterInverter
8 PowerFlex® 700S and 700H Fan Inverter Upgrade Kit (Frame 10-11)
Step 4: Removing Inverter Assemblies
Left-hand and Right-hand Inverter Assemblies
Task DescriptionRemove the two M5 Pozi-drive screws, which secure the front of the fan inverter to the drive. Proper tightening torque for reassembly is 4 N-m (35 lb.-in.).Disconnect the fan motor cable under the inverter.
Remove the four M5 Pozi-drive screws, which secure the bottom of the fan inverter to the drive. Proper tightening torque for reassembly is 4 N-m (35 lb.-in.).Disconnect the cables at X2, X8 and X3 (on left-hand and center inverters); and X2 and X8 (on right-hand inverter).
Carefully remove the inverters by sliding them out towards the front of the drive.
A
B
C
D
E
A
A
B
C
C
CC
Important: Do not damage the output transformer when removing or installing the inverter.
Bottom Viewof Power Structure
PowerFlex® 700S and 700H Fan Inverter Upgrade Kit (Frame 10-11) 9
Step 5: Removing the Inverter from the Old Inverter Assembly
Task DescriptionDisconnect the cables at connectors X4 (Blue) and X5 (Black).
A
A A
Task DescriptionRemove two M5 Pozi-drive screws, which secure the inverter board and its heatsink to the assembly carriage. Proper tightening torque for reassembly is 4 N-m (35 lb.-in.).Carefully remove the inverter board and its heatsink from the assembly carriage.
B
C
B
Right-hand Inverter Shown
Task DescriptionOn center inverter assemblies, using a 13 mm wrench, remove the nut, which secures the capacitor and fuse block bracket to the assembly. Then remove the capacitor and fuse block. You will re-use the fuse block on the new assembly. Hand tighten this nut during reassembly.
D
=
=
B
10 PowerFlex® 700S and 700H Fan Inverter Upgrade Kit (Frame 10-11)
Step 6: Installing the Inverter on the New Inverter Assembly
Installation is reverse of removal. Refer to:Step 5: Removing the Inverter from the Old Inverter Assembly on page -9.
Step 7: Installing the New Inverter Assemblies and Preparing the Drive for Use
Installation is reverse of removal. Refer to: Step 4: Removing Inverter Assemblies on page -8, Step 3: Preparing Power Structure for Inverter Assembly Removal on page -6 and Step 2: Removing Covers from the Power Structure on page -3.
Contacting Rockwell Automation Support
Before you contact Rockwell Automation for technical assistance, we suggest you please review the troubleshooting information contained in the supporting product publications first (e.g. publications PFLEX-TG002, Hardware Service Manual - PowerFlex 700S and 700H Drives, and PFLEX-IN006, Installation Instructions - PowerFlex 700S and 700H Drives).
If the problem persists, call your local distributor or contact Rockwell Automation in one of the following ways:
Be prepared to furnish the following information when you contact support:
• Product Catalog Number• Product Serial Number• Firmware Revision Level
Phone United States/Canada
1.262.512.8176 (7 AM - 6 PM CST)
1.440.646.5800 (24 hour paid support available through the TechConnect Support Program)
Outside United States/Canada
You can access the phone number for your country via the Internet:
Go to http://www.ab.com
Click on Support (http://support.rockwellautomation.com/)
Under Contact Customer Support, click on Phone Support
Internet ⇒ Go to http://www.ab.com/support/abdrives/E-mail ⇒ [email protected]
PowerFlex® 700S and 700H Fan Inverter Upgrade Kit (Frame 10-11) 11
Notes:
PDF Job Options
PDF Job OptionsLast Revison 9/30/03
TabDescription
GeneralFile Options
Compatibility:Acrobat 3.0
3Optimized PDF
Resolution:1200 dpi
Binding:Left
CompressionColor Bitmap Images
3Bicubic Downsampling at:150 dpi
3Compression:Automatic
Quality:Medium
Grayscale Bitmap Images
3Bicubic Downsampling at:150 dpi
3Compression:Automatic
Quality:Medium
Monochrome Bitmap Images
3Bicubic Downsampling at:300 dpi
3Compression:CCITT Group 4
3Compress Text and Line Art
Fonts3Embed All Fonts
3Subset All Embedded Fonts Below:100%
When Embedding Fails:Warn and Continue
Embedding:Base 14 Fonts
ColorConversion
3Leave Color Unchanged
Options
3Preserve Overprint Settings
3Preserve Under Color Removal amd Black Generation
3Preserve Transfer Functions
AdvancedOptions
3Preserve Level 2 copypage Semantics
Document Structuring Convensions (DSC)
3Process DSC
3Preserve EPS Info from DSC
3Preserve OPI Comments
3Preserve Document Info from DSC
Default Page Size
Width:612
Heigth:792
Units:Points
POD Print Specs
Print On Demand SpecificationsLast Revision 4/30/04
Publication:PFLEX-IN016A-EN-P
Quantity:Specified by Buyer
Sides:Double-sided
Body Page Count:12
Stock Weight - Body:20# bond
Ink - Body:Color Laser
Cover Count:0
Stock Weight - Cover:90# Bristol Index
Ink - Cover:Black (1-1-0-1)
Binding:Left corner staple (up to 50 pages/25 sheets)
Drilling:Three
Folding:Based on binding method
Trim Size:8.5 x 11 inches (Nominal)
File Sent:PDF
Packaging:Per vendor standard method
Delivery:Specified by Buyer
ahweilTCQF-123 Mfg Spec.xls
Publication PFLEX-IN016A-EN-P - March 2005 12 366153-P01Copyright © 2005 Rockwell Automation. All rights reserved. Printed in the U.S.A.
Front PageIntroductionWhat this Kit ContainsWhat You Need to DoStep 1: Removing Power from the DriveStep 2: Removing Covers from the Power StructureStep 3: Preparing Power Structure for Inverter Assembly RemovalStep 4: Removing Inverter AssembliesStep 5: Removing the Inverter from the Old Inverter AssemblyStep 6: Installing the Inverter on the New Inverter AssemblyStep 7: Installing the New Inverter Assemblies and Preparing the Drive for UseContacting Rockwell Automation SupportPub No. - Date