PEXTO

NO. G52 FOOTGAP SHEAR

OPERATING INSTF\UCTIONS AND PARTS IDENTIFICATION

MIMS Machinery Movers mimsriggers.com

MIMS Machinery Movers mimsriggers.com

INSTRUCTIONSFOR

ADJUSTING NO. G52 PEXTO FOOT SHEAR

1. This shear has been tested to maximum Capacity at factory. Do not exceed capacity shown onnameplate.

2_ Toset up Shear, remove from skids and placeon alevelfoundation. NOTE: When Bed is level, itrests evenly on the Leg Ledges at all four corners. If necessary, shim legs away from floor until Beddoes rest evenly on the Leg Ledges.

3. AIways keep BIades sharp. Wipethe Upper Bladewith an oily ragfrequentlyto helpto keeptheedges sharp.

4. Lubrication should be maintained between Crosshead and Holddown Bearing surfaces and alsobetween Crosshead and Leg Bearing surfaces. Oil holes are provided in the Treadle to permitlubrication to the Hinge Pin.

5. Front, Back, Side and Bevel Gauges are provided for use as desired. Side and Back Gauges aregraduated and adjustment is provided to keep graduations aligned with the Blade cutting edges.

6. lt is advisable to have an extra pair of Blades available for use when the original Blades are removedto be sharpened. Always send the Blades for regrinding to the factory where necessary specialmachines for regrinding BIades are used.

7. Toadjust ShearafterBIades have been changed) back offthe4 boltsthatsecurethe Bed totheLegs a half turn. Bed adjusting screws move Bed to position Lower Blade in relation to upper Blade.

8. Place a sheet of heavy paper between the Blades forthe full length and depress Treadle slowly. lfShear does not cut paperthe full length, move Bed inward by turning Bed Adjusting Screws equallyon each end a quarter turn at a time. lf Shear cuts paper on ends but not in center, turn CrossheadAdjustment Nut, in center of The-Rod, clockwise 1/8turn at atime, lf Shear cuts paper in center butnot on ends, reverse direction of turn on Crosshead Adjustment Nut. NOTE: This adjustment isalways made atthe factory and should not be necessary on a new Shear.

9. After adjusting for proper Blade clearance, tighten Bed to Leg bolts securely before cuttlng stock.

1 0. When ordering replacement parts from the factory, be sure to give Model, Letter and Serial Numbershown on Machine Nameplate.

Batavia Machinery, lnc.2881 Sunline DriveReno, NV 89523

775-746-2433 F 775-746-2499

-2-

MIMS Machinery Movers mimsriggers.com

MIMS Machinery Movers mimsriggers.com

PEXTO NO. 3 BACKGAUGE IDENTIFICATION CHART

fl !]

ll12II15/

D!QI± F|.H. Link (10) is assembledto R.H. Gauge Holder (6) with one pivotstud (13) to provlde fOrangular setting of backgauge.

1. 762O300442. 76220OO433. 6OO3563114. 7622400465. 7624200476. 762200O437. 7625500498. 621012084

GAUGE RODL.H. BACKGAuGE HOLDEF]HAND KNOBL.H. LINK

BACKGAuGE BAF]F].H. BACKGAuGE HOLDEF]HANDWHEEL1/4-2O X 3/8 ALLEN SET SCF]EW

-3-

9. 7623800501 0. 762240045ll. 6150120241 2. 76242OO4813. 76216OO511 4. 6490230O715. 621O1227516. 6OIOl2273

PINION

F].H. LINK

8-32 X 1/4 BH SCF]EWPOINTEF]PIVOT STUD1/2-13 HEX NUT1/2-13X 1 1/2 SCF]EW1/2-13X 1 1/4 SCF]EW

Batavia MachI.nery| Inc.288l Sunline DriveReno, NV 89523

775-746-2433 F 775-746-2499

MIMS Machinery Movers mimsriggers.com

MIMS Machinery Movers mimsriggers.com

NO. G52 PARTS IDENTIFICATION CHART

(1) HOLDDOWN SHAFT

Please refer to the Parts Identification List on page 6 for part numbers.

-4-Batavia Machinery' lnc.

288l Sunljne DriveReno, NV 89523

775-746-2433 r 775-746-2499

MIMS Machinery Movers mimsriggers.com

MIMS Machinery Movers mimsriggers.com

NO. G52 PARTS IDENTIFICATION CHART

"_(36)

-R.H.&L.H. (37&38)

BACKGAUGE BAR (39)

CROSSHEAD TIE ROD (4O)LEVER ARM - R.H. a L.H. (41 a 42)

CONNECTING SHAFT (43)

BACKGAuGE POINTER (44)

B.a. ADJUSTING KNOB (45)

B.a. BRACKET - R.H. 8, L.H. (46)B.G. ADJUSTING PINION (47)BACKGAUGE ROD (48)UPPER TREADLE ROD PIN (49)UPPER TREADLE ROD (5O)

SPRING PIN (51)

RETURN SPRING (52)

CROSSHEAD ADJUSTMENT (53l

TuRNBUCKLE NUT (54)

TURNBuCKLE (55)

LOWER TREADLE ROD (56)

LOWER TREADLE ROD PIN (57)

TREADLE HINGE PIN (58)

WARNING: Before operating' machine m!]s! be bolted to work bench. lffloor stand has been provided,machine must be bolted to floor stand with bolts provided. Stand mJ±Si be Securely laggedto floor.

-5-Batavia Machinery, Inc.

288l Sunlifle DriveReno, NV 89523

775-746-2433 F 775-746-2499

MIMS Machinery Movers mimsriggers.com

MIMS Machinery Movers mimsriggers.com

G52 PARTS IDENTIFICATION LIST

lTEMNO. PARTNO. PARTNAME

1

2345678910

i|12

13

14

15

16

17

18

19

2021

22232425262728293031

32333435363738394041

42

76268001 376261 OOO1

76201 000776245002376224002460035631 O76246OO2676221 0025762400O2763301 20994626800O34620600O27621 400066000001 2476242003276209003776203OO227621 600217621 6002976224OO307621 4000576226002076242OO397622000387624200313507001 953507001 95762090OO476203003576242OO336730230077621 6003676242003176242003276242003476281 0008762240045762240O4676242004776203000276203001 176203OO1 2

Holddown ShaftCrossheadHolddownHolddown GuideHolddown StrapHolddown Handle BallHolddown Handle BarEccentricGibGibAdjustmentScrew 1/4x 2" Sq. Hd.Treadle ShaftTreadle PlateL. H. HousingTurnbuckleL. H. SideGaugeSide TableHolddown RodHolddown PinLever Arm PinLever Arm LinkF]. H. Housing

Holddown Shaft CollarSlitting GaugeSlitting Gauge BracketR. H. Side GaugeUpper BladeLower BladeBedFront ArmFront GaugeWing NutTee BoltR. H. SideGaugeL. H. SideGaugeBevel GaugeTreadIeF]. H. Backgauge LinkL. H. Backgauge LinkBackgauge BarCrosshead Tie F]odFl. H. LeverArmL. H. LeverArm

-6-

i

Batavia Machinery, Inc.288l Sunline DriveReno, NV 89523

775-746.2433 F 775-746-2499

MIMS Machinery Movers mimsriggers.com

MIMS Machinery Movers mimsriggers.com

G52 PARTS IDENTIFICATION LIST

ITEM NO. PART NO. PART NAME

:i;::§

76268001 476242004860035631 1762200043762380050762O30O447621 6001 776203001 560OO634736621 8454576265000364302301 26000001 24762030O1 67621 6001 87621 6001 9

Connecting ShaftBackgauge PointerBackgauge Adjusting KnobF]. H. & L. H. Backgauge BracketsBackgauge Adjusting PinionBackgauge F]odUpper Treadle F]od PinUpper Treadle F]odSpring PinF]eturn SpringCrosshead AdjustmentTumbuckle NutTumbuckleLower Treadle F]odLower Treadle F]od PinTreadle Hinge Pin

-7-

2i

:2

Batavia MachineryI Inc.2881 Sunline DrlveReno, NV 89523

775-746.2433 F 775.746-2499

MIMS Machinery Movers mimsriggers.com

MIMS Machinery Movers mimsriggers.com