Perforating GunFacts™castellmx.com/pdf/gunfacts.pdf · Perforating GunFacts™ 1-11/16” SEMI EXPENDABLE THRU TUBING GUN 4 SPF - 0º PHASE Charge Arrangement: LOW SHOT DENSITY,

Titan Specialties, Ltd., P.O. Box 2316, Pampa, TX 79066 800.692.4486 www.titanspecialties.com

Your Worldwide Solution Serving the Oil & Gas Industry Since 1966

Perforating GunFacts™

• 1-11/16” Capsule Gun Systems • 2-1/8” Capsule Gun Systems • General Comments:

Semi Expendable (Capsule) Thru-Tubing Gun Systems

• 1-3/8” RTG Gun Systems • 1-9/16” RTG Gun Systems • 2” RTG Gun Systems • 2-1/2” RTG Gun Systems • General Comments:

Retrievable Thru-tubing Gun Systems

• 2-3/4” Expendable Gun Systems • 2-7/8” Expendable Gun Systems • 3-1/8” Expendable Gun Systems • 3-3/8” Expendable Gun Systems • 3-1/2” Expendable Gun Systems • 4” Expendable Gun Systems • 4-1/2” Expendable Gun Systems • 4-5/8” Expendable Gun Systems • 5” Expendable Gun Systems • 6” Expendable Gun Systems • 7” Expendable Gun Systems • General Comments:

Expendable Casing Gun Systems

• 3-1/8” EEG Gun Systems • 4” EEG Gun Systems • General Comments:

3-1/8” & 4” E.E.G. Casing Gun Systems

See General Comments sections for datasheet footnote explanations.


1-11/16” SEMI EXPENDABLE THRU TUBING GUN

4 SPF - 0º PHASE

Charge Arrangement: LOW SHOT DENSITY, SEQUENTIAL Strip Material (1): Mild Steel Strip Configuration: Threaded Charge Positioning Method: Threaded Into Formed Strip Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Continuous Gun Positioning Requirements: Roll Over Sleeve, Mechanical or Magnetic Decentralizer Initiation Point:

Gun Series 0215 – All Conveyance Methods TOP FIRED ONLY Recommended Detonating Cord: EXTRA HIGH VELOCITY - 80 grains/foot Thread Description: 5/8” – 24 TPI ENGLISH METRIC Nominal Gun Outside Diameter: 1.718 in. 43.64 mm Nominal Strip Thickness: .110 in. 2.794 mm Maximum Shot Density: 4 spf 13 spm Angular Phasing - Charge to Charge: 0º 0º Angular Phasing - Bank to Bank: 0º 0º Vertical Charge Spacing: 3.00 in. 76.2 mm Vertical Planes Perforated per Repeat Shot Pattern: 1 1 Horizontal Planes Perforated per Repeat Shot Pattern: 1 1 Minimum Recommended Cord Velocity Of Detonation: 24,750 ft/sec 7,500 m/sec Maximum 1 Hour Operating Temperature – RDX (HMX) (4,5,6): 325º F (365º F) 163º C (185º C) Pressure Rating (4): 15,000 psi 103.42 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 1.740 in. (12 in.) 44.19 mm (304.8 mm) Standard Overall Gun Lengths (7):

Strip 0215-107-041 (24 shots) 80 in. 2.03 m Strip 0215-107-041 (40 shots) 128 in. 3.25 m

Gun End to First Charge Center Distance: 5.50 in. 139.70 mm Calculated Tensile Strength Across Charge Hole (Per Side) (8): 2,400 lbs. 10,676 N Maximum Rockwell “C” Hardness (Firing Head): 38 38 Minimum Recommended Tubing Size (9): 2-3/8 in. 60.30 mm Minimum Recommended Tubing Weight (9): 4.0 lbs/ft 5.96 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry): 8.0g RDX/HMX 8.0g RDX/HMX Maximum (Average) Test Gun Swell @ 8.0g RDX (10): N/A (12) N/A (12) Maximum Charge Explosive Load - Ambient Fluid (Wet): 8.0g RDX/HMX 8.0g RDX/HMX Maximum (Average) Test Gun Swell @ 8.0g RDX (10): N/A (12) N/A (12) Minimum Recommended I.D. Running Restriction: 1.781 in. 45.24 mm Minimum Recommended Washover Pipe Clearance Requirements:

Casing Drift Diameter-to-Nominal Washover Pipe O.D. N/A (12) N/A (12)

Washover Pipe Drift Diameter-to- Nominal Gun O.D. N/A (12) N/A (12)

Vertical Drop Test (13): NOT RECOMMENDED NOT RECOMMENDED Horizontal Drop Test (13): NOT RECOMMENDED NOT RECOMMENDED Estimated Gun Assy Weight without Explosives (14): T.B.D. (11) T.B.D. (11) Estimated Gun Assy Weight with DP Charges (14): T.B.D. (11) T.B.D. (11) 112120071753



6 SPF - 0º PHASE




Gun End to First Charge Center Distance: 5.00 in. 127.00 mm Calculated Tensile Strength Across Charge Hole (Per Side) (8): 2,400 lbs. 10,676 N Maximum Rockwell “C” Hardness (Firing Head): 38 38 Minimum Recommended Tubing Size (9): 2-3/8 in. 60.30 mm Minimum Recommended Tubing Weight (9): 4.0 lbs/ft 5.96 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry): 8.0 RDX/HMX 8.0 RDX/HMX Maximum (Average) Test Gun Swell @ 8.0g RDX (10): N/A (12) N/A (12) Maximum Charge Explosive Load - Ambient Fluid (Wet): 8.0 RDX/HMX 8.0 RDX/HMX Maximum (Average) Test Gun Swell @ 8.0g RDX (10): N/A (12) N/A (12) Minimum Recommended I.D. Running Restriction: 1.781 in. 45.24 mm Minimum Recommended Washover Pipe Clearance Requirements:






4 SPF - 0º PHASE




Gun End to First Charge Center Distance: 5.50 in. 139.70 mm Calculated Tensile Strength Across Charge Hole (Per Side) (8): 2,400 lbs. 10,676 N Maximum Rockwell “C” Hardness (Firing Head): 38 38 Minimum Recommended Tubing Size (9): 2-7/8 in. 73.03 mm Minimum Recommended Tubing Weight (9): 6.40 lbs/ft 9.54 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry): 15.0g RDX/HMX 15.0g RDX/HMX Maximum (Average) Test Gun Swell @ 15.0g RDX (10): N/A (12) N/A (12) Maximum Charge Explosive Load - Ambient Fluid (Wet): 15.0g RDX/HMX 15.0g RDX/HMX Maximum (Average) Test Gun Swell @ 15.0g RDX (10): N/A (12) N/A (12) Minimum Recommended I.D. Running Restriction: 2.25 in. 57.15 mm Minimum Recommended Washover Pipe Clearance Requirements:






6 SPF - 0º PHASE




Gun End to First Charge Center Distance: 5.50 in. 139.70 mm Calculated Tensile Strength Across Charge Hole (Per Side) (8): 2,400 lbs. 10,676 N Maximum Rockwell “C” Hardness (Firing Head): 38 38 Minimum Recommended Tubing Size (9): 2-7/8 in. 73.03 mm Minimum Recommended Tubing Weight (9): 6.40 lbs/ft 9.54 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry): 15.0 RDX/HMX 15.0 RDX/HMX Maximum (Average) Test Gun Swell @ 15.0g RDX (10): N/A (12) N/A (12) Maximum Charge Explosive Load - Ambient Fluid (Wet): 15.0 RDX/HMX 15.0 RDX/HMX Maximum (Average) Test Gun Swell @ 15.0g RDX (10): N/A (12) N/A (12) Minimum Recommended I.D. Running Restriction: 2.25 in. 57.15 mm Minimum Recommended Washover Pipe Clearance Requirements:




GENERAL COMMENTS Semi Expendable (Capsule), Thru-tubing Gun Systems

This document is for informational purposes only and is intended to aid the user in the decision making process. The information contained herein represents typical, average values obtained in accordance with accepted test methods/procedures and are subject to normal manufacturing variations. Translation of said data to downhole conditions is the responsibility of the service company/customer. This document is supplied as a technical service and is subject to change without notice. Check with Titan Specialties to assure current information. FOOTNOTES 1. The information contained herein is relevant to gun hardware purchased after July 1, 1996, is typical test data,

and not for specification. 2. Explosive transfer reliability between guns can be affected by the condition of the hardware, type and quality of

the explosive components, and assembly techniques; and are undertaken at Service Company’s own risk. Consult with a reputable explosives manufacturer when case-specific information is required.

3. Peroxide cured nitrile is one of the most common O-ring materials used in “normal” downhole applications.

Consult a reputable O-ring manufacturer for recommendations when non-typical downhole conditions are encountered.

4. Maximum operating temperature and pressure of the perforating gun hardware is most dependent upon O-ring

selection. Temperature and pressure ratings are dramatically affected by factors such as O-ring compound, curing process, O-ring hardness, and clearance gap (to name but a few). Improper selection and care of the O-rings and hardware can result in premature seal failure. Value shown is based upon theoretical calculations.

5. Minimum operating temperature for peroxide cured nitrile O-rings is approximately -20º F (-29º C). O-rings

designed for Arctic service and hostile environments are available upon request. 6. Maximum operating temperature of the perforating gun system is usually affiliated with the explosives contained

therein. Typically, the temperature rating of the explosive charge is well below that of the gun hardware. Reference “temperature versus exposure time” data published by various explosives and charge manufacturers for this information.

7. Customized gun lengths are available upon request. 8. Due to the tremendous variety of sub/firing head designs, this calculation is based upon gun-to-sub connections

only. 9. The minimum tubing size/weight recommendation assumes that the tubing is in good condition and properly

supported. 10. Maximum and average gun swell measurements shown herein were taken from laboratory guns containing steel

backed charges which were tested at the surface. Gun swell experienced downhole may differ dramatically depending upon numerous factors such as fluid environment, pressure, temperature, gun clearance, charge case material, charge liner material, charge manufacturer, etc..

11. T.B.D. is an acronym for “To Be Determined”. 12. N/A is an acronym for “Not Applicable”. 13. Vertical and horizontal drop test data contained herein does not imply that a gun is safe to run down hole if

inadvertently dropped less than the values shown. It is the service company’s responsibility to inspect all equipment after such an occurrence and determine serviceability.

14. Estimated gun assembly weight with DP or BH charges will vary depending upon the type of charge. Value shown

is the combined weight of the gun body, end fittings, fully loaded charge tube, detonating cord, miscellaneous small hardware items, and charges from one such charge manufacturer.


1 3/8” RETRIEVABLE, THRU-TUBING GUN

4 SPF - 0º PHASE

Charge Arrangement: LOW SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, Cold Drawn, Seamless Steel Tubing Gun Body Configuration: Bolted & Scalloped Charge Positioning Method: Flat Strip Conveyance Methods: Wireline Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice Gun Positioning Requirements: Optional Initiation Point: Gun Series 0327 - Wireline Bolted Style BOTTOM Fired Gun Series XXXX - Not Available Recommended Detonating Cord: 40 grains/foot, FLAT RIBBON Bolted RTG Thread Description: 10-32 UNC-2A O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-211 ENGLISH METRIC Nominal Gun Outside Diameter: 1.375 in. 34.9 mm Nominal Gun Body Wall Thickness: .165 in. 4.19 mm Maximum Shot Density: 4 spf 13 spm Angular Phasing - Charge to Charge: 0º 0º Angular Phasing - Bank to Bank: 0º 0º Vertical Charge Spacing: 3.00 in. 76.2 mm Vertical Planes Perforated per Repeat Shot Pattern: 1 1 Horizontal Planes Perforated per Repeat Shot Pattern: 1 1 Minimum Recommended Cord Velocity Of Detonation: 21,000 ft/sec 6,400 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 21,000 psi 144.79 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 1.012 in. (10 in.) 25.70 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy 0327-A03-041 (8 shots) 33 in. .838 m Gun Assy 0327-A04-041 (12 shots) 45 in. 1.14 m Gun Assy 0327-A07-041 (24 shots) 81 in. 2.06 m Gun Assy 0327-A11-041 (40 shots) 129 in. 3.28 m Gun Assy 0327-A21-041 (80 shots) 249 in. 6.32 m Tandem Shoulder Length - Wireline: .50 in. 12.70 mm Gun End to Center of First Scallop Distance: 6.00 in. 152.40 mm Calculated Tensile Strength - Bolted (8): 24,000 lbs. 106,700 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Tubing Size (9): 2-1/16 in. 52.40 mm

Minimum Recommended Tubing Weight (9): 3.25 lbs/ft 4.85 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry): 1.8g RDX/HMX 1.8g RDX/HMX Maximum (Average) Test Gun Swell @ 1.8g RDX (10): 1.476 in (1.447 in) 37.49 mm (36.75 mm) Maximum Charge Explosive Load - Ambient Fluid (Wet): 1.8g RDX/HMX 1.8g RDX/HMX Maximum (Average) Test Gun Swell @ 1.8g RDX (10): 1.451 in (1.428 in) 36.86 mm (36.27 mm) Minimum Recommended I.D. Running Restriction: 1.65 in. 41.91 mm Minimum Recommended Washover Pipe Clearance Requirements: Casing Drift Diameter-to-Nominal Washover Pipe O.D. N/A (12)

N/A (12) Washover Pipe Drift Diameter-to-Nominal Gun O.D. N/A (12)

N/A (12) Vertical Drop Test (11: T.B.D. (11) T.B.D. (11) Horizontal Drop Test (11): T.B.D. (11) T.B.D. (11) Estimated Gun Assy Weight without Explosives: 2.00 lbs/ft 2.98 kg/m Estimated Gun Assy Weight with DP Charge (14): 3.00 lbs/ft 4.46 kg/m 101820071325



4 SPF - 180º PHASE

Charge Arrangement: LOW SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, Cold Drawn, Seamless Steel Tubing Gun Body Configuration: Bolted & Scalloped Charge Positioning Method: Flat Strip Conveyance Methods: Wireline Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice Gun Positioning Requirements: Optional Initiation Point: Gun Series 0327 - Wireline Bolted Style BOTTOM Fired Gun Series XXXX - Not Available Recommended Detonating Cord: 40 grains/foot, FLAT RIBBON Bolted RTG Thread Description: 10-32 UNC-2A O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-211 ENGLISH METRIC Nominal Gun Outside Diameter: 1.375 in. 34.9 mm Nominal Gun Body Wall Thickness: .165 in. 4.19 mm Maximum Shot Density: 4 spf 13 spm Angular Phasing - Charge to Charge: 180º 180º Angular Phasing - Bank to Bank: 180º 180º Vertical Charge Spacing: 3.00 in. 76.2 mm Vertical Planes Perforated per Repeat Shot Pattern: 2 2 Horizontal Planes Perforated per Repeat Shot Pattern: 2 2 Minimum Recommended Cord Velocity Of Detonation: 21,000 ft/sec 6,400 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 22,000 psi 151.68 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 1.012 in. (10 in.) 25.70 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy 0327-A03-042 (8 shots) 33 in. .838 m Gun Assy 0327-A04-042 (12 shots) 45 in. 1.14 m Gun Assy 0327-A07-042 (24 shots) 81 in. 2.06 m Gun Assy 0327-A11-042 (40 shots) 129 in. 3.28 m Gun Assy 0327-A21-042 (80 shots) 249 in. 6.32 m Tandem Shoulder Length - Wireline: .50 in. 12.70 mm Gun End to Center of First Scallop Distance: 6.00 in. 152.40 mm Calculated Tensile Strength - Bolted (8): 24,000 lbs. 106,700 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Tubing Size (9): 2-1/16 in. 52.40

Minimum Recommended Tubing Weight (9): 3.25 lbs/ft 4.85 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry): 1.8g RDX/HMX 1.8g RDX/HMX Maximum (Average) Test Gun Swell @ 1.8g RDX (10): T.B.D. (11) T.B.D. (11) Maximum Charge Explosive Load - Ambient Fluid (Wet): 1.8g RDX/HMX 1.8g RDX/HMX Maximum (Average) Test Gun Swell @ 1.8g RDX (10): 1.460 in. (1.452 in) 37.08 mm (36.88 mm) Minimum Recommended I.D. Running Restriction: 1.65 in. 41.91 mm Minimum Recommended Washover Pipe Clearance Requirements: Casing Drift Diameter-to-Nominal Washover Pipe O.D. N/A (12)





4 SPF - 0º PHASE (Threaded)

Charge Arrangement: LOW SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, Cold Drawn, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0227 - Wireline Style BOTTOM Fired Gun Series 0527 - TCP Style TOP Fired Recommended Detonating Cord: 40 grains/foot, FLAT RIBBON Thread Description: 1-1/8” – 12 STUB ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-120 ENGLISH METRIC Nominal Gun Outside Diameter: 1.375 in. 34.9 mm Nominal Gun Body Wall Thickness: .165 in. 4.19 mm Maximum Shot Density: 4 spf 13 spm Angular Phasing - Charge to Charge: 0º 0º Angular Phasing - Bank to Bank: 0º 0º Vertical Charge Spacing: 3.00 in. 76.2 mm Vertical Planes Perforated per Repeat Shot Pattern: 1 1 Horizontal Planes Perforated per Repeat Shot Pattern: 1 1 Minimum Recommended Cord Velocity Of Detonation: 21,000 ft/sec 6,400 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 21,000 psi 144.79 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 1.012 in. (10 in.) 25.70 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0227 or 0527)-A04-041 (12 shots) 45 in. 1.14 m Gun Assy (0227 or 0527)-A07-041 (24 shots) 81 in. 2.06 m Gun Assy (0227 or 0527)-A11-041 (40 shots) 129 in. 3.28 m Gun Assy (0227 or 0527)-A21-041 (80 shots) 249 in. 6.32 m Tandem Shoulder Length – Wireline (TCP Grooved): 1.25 in. (2.50 in.) 31.75 mm (63.50 mm) Gun End to Center of First Scallop Distance: 6.00 in. 152.40 mm Calculated Break Point Tensile Strength - Hardware Only (8): 59,000 lbs. 262,445 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Tubing Size (9): 2-1/16 in. 52.40 mm



































Charge Arrangement: MEDIUM SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, Cold Drawn, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0227 - Wireline Style BOTTOM Fired Gun Series 0527 - TCP Style TOP Fired Recommended Detonating Cord: 40 grains/foot, FLAT RIBBON Thread Description: 1-1/8” – 12 STUB ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-120 ENGLISH METRIC Nominal Gun Outside Diameter: 1.375 in. 34.9 mm Nominal Gun Body Wall Thickness: .165 in. 4.19 mm Maximum Shot Density: 6 spf 19 spm Angular Phasing - Charge to Charge: 60º 60º Angular Phasing - Bank to Bank: 60º 60º Vertical Charge Spacing: 2.00 in. 50.8 mm Vertical Planes Perforated per Repeat Shot Pattern: 6 6 Horizontal Planes Perforated per Repeat Shot Pattern: 6 6 Minimum Recommended Cord Velocity Of Detonation: 22,000 ft/sec 6,700 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 22,000 psi 151.68 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 1.012 in. (10 in.) 25.70 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0227 or 0527)-A04-066 (18 shots) 45 in. 1.14 m Gun Assy (0227 or 0527)-A07-066 (36 shots) 81 in. 2.06 m Gun Assy (0227 or 0527)-A11-066 (60 shots) 129 in. 3.28 m Gun Assy (0227 or 0527)-A21-066 (120 shots) 249 in. 6.32 m Tandem Shoulder Length – Wireline (TCP Grooved): 1.25 in. (2.50 in.) 31.75 mm (63.50 mm) Gun End to Center of First Scallop Distance: 5.50 in. 139.70 mm Calculated Break Point Tensile Strength - Hardware Only (8): 59,000 lbs. 262,445 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Tubing Size (9): 2-1/16 in. 52.40 mm






4 SPF - 0º PHASE

Charge Arrangement: LOW SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, Cold Drawn, Seamless Steel Tubing Gun Body Configuration: Bolted (or Threaded) & Scalloped Charge Positioning Method: Flat Strip or Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0320 (0220) – W/L Bolted (Threaded) BOTTOM Fired Gun Series 0220 - TCP Threaded Style TOP Fired Recommended Detonating Cord: 40 grains/foot, FLAT RIBBON Bolted RTG Thread Description: 1/4-20 UNC-2A Thread Description: 1-9/32” - 12 STUB ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size - Bolted (TCP Threaded): 568-214 (568-215) ENGLISH METRIC Nominal Gun Outside Diameter: 1.563 in. 39.7 mm Nominal Gun Body Wall Thickness: .172 in. 4.37 mm Maximum Shot Density: 4 spf 13 spm Angular Phasing - Charge to Charge: 0º 0º Angular Phasing - Bank to Bank: 0º 0º Vertical Charge Spacing: 3.00 in. 76.2 mm Vertical Planes Perforated per Repeat Shot Pattern: 1 1 Horizontal Planes Perforated per Repeat Shot Pattern: 1 1 Minimum Recommended Cord Velocity Of Detonation: 21,000 ft/sec 6,400 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 19,000 psi 131.01 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 1.187 in. (10 in.) 30.15 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0320 or 0220*)-A04-041 (12 shots) 45 in. (48 in.*) 1.14 m (1.22 m*) Gun Assy (0320 or 0220*)-A07-041 (24 shots) 81 in. (84 in.*) 2.06 m (2.13 m*) Gun Assy (0320 or 0220*)-A11-041 (40 shots) 129 in. (132 in.*) 3.28 m (3.35 m*) Gun Assy (0320 or 0220*)-A21-041 (80 shots) 249 in. (252 in.*) 6.32 m (6.40 m*) Tandem Shoulder Length – W/L Bolted, Threaded (TCP Grooved): .50, 1.25 in. (2.50 in.) 12.70, 31.75 mm (63.50 mm) Gun End to Center of First Scallop Distance: 6.00 in. 152.40 mm Calculated Tensile Strength - Bolted (Threaded) (8): 35,000 lbs. (80,000 lbs.) 155,750 N (356,000 N) Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Tubing Size (9): 2-3/8 in. 60.30 mm

Minimum Recommended Tubing Weight (9): 4.0 lbs/ft 5.96 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry): T.B.D. (11) T.B.D. (11) Maximum (Average) Test Gun Swell @ 3.2g RDX (10): 1.703 in. (1.680 in.) 43.26 mm (42.67 mm) Maximum Charge Explosive Load - Ambient Fluid (Wet): T.B.D. (11) T.B.D. (11) Maximum (Average) Test Gun Swell @ 3.2g RDX (10): 1.676 in. (1.661 in.) 42.57 mm (42.19 mm) Minimum Recommended I.D. Running Restriction: 1.78 in. 45.21 mm Minimum Recommended Washover Pipe Clearance Requirements:


Washover Pipe Drift Diameter-to-Nominal Gun O.D. N/A (12) N/A (12)

Vertical Drop Test (13): T.B.D. (11) T.B.D. (11) Horizontal Drop Test (13): T.B.D. (11) T.B.D. (11) Estimated Gun Assy Weight without Explosives: 2.45 lbs/ft 3.64 kg/m Estimated Gun Assy Weight with DP Charge (14): 2.72 lbs/ft 4.06 kg/m 011720081746



4 SPF - 60º PHASE

Charge Arrangement: LOW SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, Cold Drawn, Seamless Steel Tubing Gun Body Configuration: Bolted (or Threaded) & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0320 (0220) – W/L Bolted (Threaded) BOTTOM Fired Gun Series 0220 - TCP Threaded Style TOP Fired Recommended Detonating Cord: 40 grains/foot, FLAT RIBBON Bolted RTG Thread Description: 1/4-20 UNC-2A Thread Description: 1-9/32” - 12 STUB ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size - Bolted (TCP Threaded): 568-214 (568-215) ENGLISH METRIC Nominal Gun Outside Diameter: 1.563 in. 39.7 mm Nominal Gun Body Wall Thickness: .172 in. 4.37 mm Maximum Shot Density: 4 spf 13 spm Angular Phasing - Charge to Charge: 60º 60º Angular Phasing - Bank to Bank: 60º 60º Vertical Charge Spacing: 3.00 in. 76.2 mm Vertical Planes Perforated per Repeat Shot Pattern: 6 6 Horizontal Planes Perforated per Repeat Shot Pattern: 6 6 Minimum Recommended Cord Velocity Of Detonation: 21,000 ft/sec 6,400 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 20,000 psi 137.90 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 1.187 in. (10 in.) 30.15 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0320 or 0220*)-A04-046 (12 shots) 45 in. (48 in.*) 1.14 m (1.22 m*) Gun Assy (0320 or 0220*)-A07-046 (24 shots) 81 in. (84 in.*) 2.06 m (2.13 m*) Gun Assy (0320 or 0220*)-A11-046 (40 shots) 129 in. (132 in.*) 3.28 m (3.35 m*) Gun Assy (0320 or 0220*)-A21-046 (80 shots) 249 in. (252 in.*) 6.32 m (6.40 m*) Tandem Shoulder Length – W/L Bolted, Threaded (TCP Grooved): .50, 1.25 in. (2.50 in.) 12.70, 31.75 mm (63.50 mm) Gun End to Center of First Scallop Distance: 6.00 in. 152.40 mm Calculated Tensile Strength - Bolted (Threaded) (8): 35,000 lbs. (80,000 lbs.) 155,750 N (356,000 N) Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Tubing Size (9): 2-3/8 in. 60.30 mm

Minimum Recommended Tubing Weight (9): 4.00 lbs/ft 5.96 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry): 3.2g RDX/HMX 3.2g RDX/HMX Maximum (Average) Test Gun Swell @ 3.2g RDX (10): 1.702 in. (1.688 in.) 43.23 mm (42.87 mm) Maximum Charge Explosive Load - Ambient Fluid (Wet): 3.2g RDX/HMX 3.2g RDX/HMX (Average) Test Gun Swell @ 3.2g RDX (10): 1.667 in. (1.664 in.) 42.34 mm (42.27 mm) Minimum Recommended I.D. Running Restriction: 1.78 in. 45.21 mm Minimum Recommended Washover Pipe Clearance Requirements:






4 SPF - 90º PHASE

Charge Arrangement: LOW SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, Cold Drawn, Seamless Steel Tubing Gun Body Configuration: Bolted (or Threaded) & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0320 (0220) – W/L Bolted (Threaded) BOTTOM Fired Gun Series 0220 - TCP Threaded Style TOP Fired Recommended Detonating Cord: 40 grains/foot, FLAT RIBBON Bolted RTG Thread Description: 1/4-20 UNC-2A Thread Description: 1-9/32” - 12 STUB ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size - Bolted (TCP Threaded): 568-214 (568-215) ENGLISH METRIC Nominal Gun Outside Diameter: 1.563 in. 39.7 mm Nominal Gun Body Wall Thickness: .172 in. 4.37 mm Maximum Shot Density: 4 spf 13 spm Angular Phasing - Charge to Charge: 90º 90º Angular Phasing - Bank to Bank: 90º 90º Vertical Charge Spacing: 3.00 in. 76.2 mm Vertical Planes Perforated per Repeat Shot Pattern: 4 4 Horizontal Planes Perforated per Repeat Shot Pattern: 4 4 Minimum Recommended Cord Velocity Of Detonation: 21,000 ft/sec 6,400 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 20,000 psi 137.90 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 1.187 in. (10 in.) 30.15 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0320 or 0220*)-A04-044 (12 shots) 45 in. (48 in.*) 1.14 m (1.22 m*) Gun Assy (0320 or 0220*)-A07-044 (24 shots) 81 in. (84 in.*) 2.06 m (2.13 m*) Gun Assy (0320 or 0220*)-A11-044 (40 shots) 129 in. (132 in.*) 3.28 m (3.35 m*) Gun Assy (0320 or 0220*)-A21-044 (80 shots) 249 in. (252 in.*) 6.32 m (6.40 m*) Tandem Shoulder Length – W/L Bolted, Threaded (TCP Grooved): .50, 1.25 in. (2.50 in.) 12.70, 31.75 mm (63.50 mm) Gun End to Center of First Scallop Distance: 6.00 in. 152.40 mm Calculated Tensile Strength - Bolted (Threaded) (8): 35,000 lbs. (80,000 lbs.) 155,750 N (356,000 N) Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Tubing Size (9): 2-3/8 in. 60.30 mm

Minimum Recommended Tubing Weight (9): 4.00 lbs/ft 5.96 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry): T.B.D. (11) T.B.D. (11) Maximum (Average) Test Gun Swell @ RDX (10): T.B.D. (11) T.B.D. (11) Maximum Charge Explosive Load - Ambient Fluid (Wet): T.B.D. (11) T.B.D. (11) Maximum (Average) Test Gun Swell @ 3.2g RDX (10): T.B.D. (11) T.B.D. (11) Minimum Recommended I.D. Running Restriction: 1.78 in. 45.21 mm Minimum Recommended Washover Pipe Clearance Requirements:






4 SPF - 180º PHASE

Charge Arrangement: LOW SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, Cold Drawn, Seamless Steel Tubing Gun Body Configuration: Bolted (or Threaded) & Scalloped Charge Positioning Method: Flat Strip or Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0320 (0220) – W/L Bolted (Threaded) BOTTOM Fired Gun Series 0220 - TCP Threaded Style TOP Fired Recommended Detonating Cord: 40 grains/foot, FLAT RIBBON Bolted RTG Thread Description: 1/4-20 UNC-2A Thread Description: 1-9/32” - 12 STUB ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size - Bolted (TCP Threaded): 568-214 (568-215) ENGLISH METRIC Nominal Gun Outside Diameter: 1.563 in. 39.7 mm Nominal Gun Body Wall Thickness: .172 in. 4.37 mm Maximum Shot Density: 4 spf 13 spm Angular Phasing - Charge to Charge: 180º 180º Angular Phasing - Bank to Bank: 180º 180º Vertical Charge Spacing: 3.00 in. 76.2 mm Vertical Planes Perforated per Repeat Shot Pattern: 2 2 Horizontal Planes Perforated per Repeat Shot Pattern: 2 2 Minimum Recommended Cord Velocity Of Detonation: 21,000 ft/sec 6,400 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 20,000 psi 137.90 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 1.187 in. (10 in.) 30.15 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0320 or 0220*)-A04-042 (12 shots) 45 in. (48 in.*) 1.14 m (1.22 m*) Gun Assy (0320 or 0220*)-A07-042 (24 shots) 81 in. (84 in.*) 2.06 m (2.13 m*) Gun Assy (0320 or 0220*)-A11-042 (40 shots) 129 in. (132 in.*) 3.28 m (3.35 m*) Gun Assy (0320 or 0220*)-A21-042 (80 shots) 249 in. (252 in.*) 6.32 m (6.40 m*) Tandem Shoulder Length - W/L Bolted, Threaded (TCP Grooved): .50, 1.25 in. (2.50 in.) 12.70, 31.75 mm (63.50 mm) Gun End to Center of First Scallop Distance: 6.00 in. 152.40 mm Calculated Tensile Strength - Bolted (Threaded) (8): 35,000 lbs. (80,000 lbs.) 155,750 N (356,000 N) Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Tubing Size (9): 2-3/8 in. 60.30 mm

Minimum Recommended Tubing Weight (9): 4.0 lbs/ft 5.96 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry): T.B.D. (11) T.B.D. (11) Maximum (Average) Test Gun Swell @ 3.2g RDX (10): 1.716 in. (1.702 in.) 43.59 mm (43.23 mm) Maximum Charge Explosive Load - Ambient Fluid (Wet): T.B.D. (11) T.B.D. (11) Maximum (Average) Test Gun Swell @ 3.2g RDX (10): 1.702 in. (1.664 in.) 43.23 mm (42.27 mm) Minimum Recommended I.D. Running Restriction: 1.78 in. 45.21 mm Minimum Recommended Washover Pipe Clearance Requirements:






6 SPF - 0º PHASE

Charge Arrangement: MEDIUM SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, Cold Drawn, Seamless Steel Tubing Gun Body Configuration: Bolted (or Threaded) & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0320 (0220) – W/L Bolted (Threaded) BOTTOM Fired Gun Series 0220 - TCP Style TOP Fired Recommended Detonating Cord: 40 grains/foot, FLAT RIBBON Bolted RTG Thread Description: 1/4-20 UNC-2A Thread Description: 1-9/32” - 12 STUB ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size - Bolted (TCP Threaded): 568-214 (568-215) ENGLISH METRIC Nominal Gun Outside Diameter: 1.563 in. 39.7 mm Nominal Gun Body Wall Thickness: .172 in. 4.37 mm Maximum Shot Density: 6 spf 19 spm Angular Phasing - Charge to Charge: 0º 0º Angular Phasing - Bank to Bank: 0º 0º Vertical Charge Spacing: 2.00 in. 50.8 mm Vertical Planes Perforated per Repeat Shot Pattern: 1 1 Horizontal Planes Perforated per Repeat Shot Pattern: 1 1 Minimum Recommended Cord Velocity Of Detonation: 22,000 ft/sec 6,700 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 15,000 psi 103.43 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 1.187 in. (10 in.) 30.15 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0320 or 0220*)-A04-061 (18 shots) 45 in. (48 in.*) 1.14 m (1.22 m*) Gun Assy (0320 or 0220*)-A07-061 (36 shots) 81 in. (84 in.*) 2.06 m (2.13 m*) Gun Assy (0320 or 0220*)-A11-061 (60 shots) 129 in. (132 in.*) 3.28 m (3.35 m*) Gun Assy (0320 or 0220*)-A21-061 (120 shots) 249 in. (252 in.*) 6.32 m (6.40 m*) Tandem Shoulder Length – W/L Bolted, Threaded (TCP Grooved): .50, 1.25 in. (2.50 in.) 12.70, 31.75 mm (63.50 mm) Gun End to Center of First Scallop Distance: 5.50 in. 139.70 mm Calculated Tensile Strength – Bolted (Threaded) (8): 35,000 lbs. (80,000 lbs.) 155,750 N (356,000 N) Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Tubing Size (9): 2-3/8 in. 60.30 mm

Minimum Recommended Tubing Weight (9): 4.0 lbs/ft 5.96 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry): NOT RECOMMENDED NOT RECOMMENDED Maximum (Average) Test Gun Swell @ RDX (10): NOT RECOMMENDED NOT RECOMMENDED Maximum Charge Explosive Load - Ambient Fluid (Wet): 3.2g RDX/HMX 3.2g RDX/HMX Maximum (Average) Test Gun Swell @ 3.2g RDX (10): 1.741 in. (1.689 in.) 44.22 mm (42.90 mm) Minimum Recommended I.D. Running Restriction: 1.78 in. 45.21 mm Minimum Recommended Washover Pipe Clearance Requirements:






6 SPF - 60º PHASE

Charge Arrangement: MEDIUM SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, Cold Drawn, Seamless Steel Tubing Gun Body Configuration: Bolted (or Threaded) & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0320 (0220) – W/L Bolted (Threaded) BOTTOM Fired Gun Series 0220 - TCP Style TOP Fired Recommended Detonating Cord: 40 grains/foot, FLAT RIBBON Bolted RTG Thread Description: 1/4-20 UNC-2A Thread Description: 1-9/32” - 12 STUB ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size - Bolted (TCP Threaded): 568-214 (568-215) ENGLISH METRIC Nominal Gun Outside Diameter: 1.563 in. 39.7 mm Nominal Gun Body Wall Thickness: .172 in. 4.37 mm Maximum Shot Density: 6 spf 19 spm Angular Phasing - Charge to Charge: 60º 60º Angular Phasing - Bank to Bank: 60º 60º Vertical Charge Spacing: 2.00 in. 50.8 mm Vertical Planes Perforated per Repeat Shot Pattern: 6 6 Horizontal Planes Perforated per Repeat Shot Pattern: 6 6 Minimum Recommended Cord Velocity Of Detonation: 22,000 ft/sec 6,700 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 20,000 psi 137.90 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 1.187 in. (10 in.) 30.15 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0320 or 0220*)-A04-066 (18 shots) 45 in. (48 in.*) 1.14 m (1.22 m*) Gun Assy (0320 or 0220*)-A07-066 (36 shots) 81 in. (84 in.*) 2.06 m (2.13 m*) Gun Assy (0320 or 0220*)-A11-066 (60 shots) 129 in. (132 in.*) 3.28 m (3.35 m*) Gun Assy (0320 or 0220*)-A21-066 (120 shots) 249 in. (252 in.*) 6.32 m (6.40 m*) Tandem Shoulder Length – W/L Bolted, Threaded (TCP Grooved): .50, 1.25 in. (2.50 in.) 12.70, 31.75 mm (63.50 mm) Gun End to Center of First Scallop Distance: 5.50 in. 139.70 mm Calculated Tensile Strength - Bolted (Threaded) (8): 35,000 lbs. (80,000 lbs.) 155,750 N (356,000 N) Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Tubing Size (9): 2-3/8 in. 60.30 mm

Minimum Recommended Tubing Weight (9): 4.0 lbs/ft 5.96 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry): NOT RECOMMENDED NOT RECOMMENDED Maximum (Average) Test Gun Swell @ RDX (10): NOT RECOMMENDED NOT RECOMMENDED Maximum Charge Explosive Load - Ambient Fluid (Wet): 3.2g RDX/HMX 3.2g RDX/HMX Maximum (Average) Test Gun Swell @ 3.2g RDX (10): 1.672 in. (1.659 in.) 42.67 mm (42.14 mm) Minimum Recommended I.D. Running Restriction: 1.78 in. 45.21 mm Minimum Recommended Washover Pipe Clearance Requirements:






4 SPF - 15º PHASE, LOW SIDE, 2 BANK

Charge Arrangement: LOW SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, Cold Drawn, Seamless Steel Tubing Gun Body Configuration: Bolted (or Threaded) & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0320 (0220) – W/L Bolted (Threaded) BOTTOM Fired Gun Series 0220 - TCP Threaded Style TOP Fired Recommended Detonating Cord: 40 grains/foot, FLAT RIBBON Bolted RTG Thread Description: 1/4-20 UNC-2A Thread Description: 1-9/32” - 12 STUB ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size - Bolted (TCP Threaded): 568-214 (568-215) ENGLISH METRIC Nominal Gun Outside Diameter: 1.563 in. 39.7 mm Nominal Gun Body Wall Thickness: .172 in. 4.37 mm Maximum Shot Density: 4 spf 13 spm Angular Phasing - Charge to Charge: 15º 15º Angular Phasing - Bank to Bank: 15º 15º Vertical Charge Spacing: 3.00 in. 76.2 mm Vertical Planes Perforated per Repeat Shot Pattern: 2 2 Horizontal Planes Perforated per Repeat Shot Pattern: 2 2 Minimum Recommended Cord Velocity Of Detonation: 21,000 ft/sec 6,400 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 19,000 psi 131.01 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 1.187 in. (10 in.) 30.15 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0320 or 0220*)-A04-D415 (12 shots) 45 in. (48 in.*) 1.14 m (1.22 m*) Gun Assy (0320 or 0220*)-A07-D415 (24 shots) 81 in. (84 in.*) 2.06 m (2.13 m*) Gun Assy (0320 or 0220*)-A11-D415 (40 shots) 129 in. (132 in.*) 3.28 m (3.35 m*) Gun Assy (0320 or 0220*)-A21-D415 (80 shots) 249 in. (252 in.*) 6.32 m (6.40 m*) Tandem Shoulder Length – W/L Bolted, Threaded (TCP Grooved): .50, 1.25 in. (2.50 in.) 12.70, 31.75 mm (63.50 mm) Gun End to Center of First Scallop Distance: 6.00 in. 152.40 mm Calculated Tensile Strength - Bolted (Threaded) (8): 35,000 lbs. (80,000 lbs.) 155,750 N (356,000 N) Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Tubing Size (9): 2-3/8 in. 60.30 mm








Charge Arrangement: LOW SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, Cold Drawn, Seamless Steel Tubing Gun Body Configuration: Bolted (or Threaded) & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0320 (0220) – W/L Bolted (Threaded) BOTTOM Fired Gun Series 0220 - TCP Threaded Style TOP Fired Recommended Detonating Cord: 40 grains/foot, FLAT RIBBON Bolted RTG Thread Description: 1/4-20 UNC-2A Thread Description: 1-9/32” - 12 STUB ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size - Bolted (TCP Threaded): 568-214 (568-215) ENGLISH METRIC Nominal Gun Outside Diameter: 1.563 in. 39.7 mm Nominal Gun Body Wall Thickness: .172 in. 4.37 mm Maximum Shot Density: 4 spf 13 spm Angular Phasing - Charge to Charge: 30º 30º Angular Phasing - Bank to Bank: 30º 30º Vertical Charge Spacing: 3.00 in. 76.2 mm Vertical Planes Perforated per Repeat Shot Pattern: 2 2 Horizontal Planes Perforated per Repeat Shot Pattern: 2 2 Minimum Recommended Cord Velocity Of Detonation: 21,000 ft/sec 6,400 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 20,000 psi 137.90 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 1.187 in. (10 in.) 30.15 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0320 or 0220*)-A04-D430 (12 shots) 45 in. (48 in.*) 1.14 m (1.22 m*) Gun Assy (0320 or 0220*)-A07-D430 (24 shots) 81 in. (84 in.*) 2.06 m (2.13 m*) Gun Assy (0320 or 0220*)-A11-D430 (40 shots) 129 in. (132 in.*) 3.28 m (3.35 m*) Gun Assy (0320 or 0220*)-A21-D430 (80 shots) 249 in. (252 in.*) 6.32 m (6.40 m*) Tandem Shoulder Length - W/L Bolted, Threaded (TCP Grooved): .50, 1.25 in. (2.50 in.) 12.70, 31.75 mm (63.50 mm) Gun End to Center of First Scallop Distance: 6.00 in. 152.40 mm Calculated Tensile Strength - Bolted (Threaded) (8): 35,000 lbs. (80,000 lbs.) 155,750 N (356,000 N) Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Tubing Size (9): 2-3/8 in. 60.30 mm

Minimum Recommended Tubing Weight (9): 4.0 lbs/ft 5.96 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry): T.B.D. (11) T.B.D. (11)

Maximum (Average) Test Gun Swell @ RDX (10): T.B.D. (11) T.B.D. (11) Maximum Charge Explosive Load - Ambient Fluid (Wet): T.B.D. (11) T.B.D. (11) Maximum (Average) Test Gun Swell @ 3.2g RDX (10): T.B.D. (11) T.B.D. (11) Minimum Recommended I.D. Running Restriction: 1.78 in. 45.21 mm Minimum Recommended Washover Pipe Clearance Requirements:























Charge Arrangement: MEDIUM SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, Cold Drawn, Seamless Steel Tubing Gun Body Configuration: Bolted (or Threaded) & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0320 (0220) – W/L Bolted (Threaded) BOTTOM Fired Gun Series 0220 - TCP Style TOP Fired Recommended Detonating Cord: 40 grains/foot, FLAT RIBBON Bolted RTG Thread Description: 1/4-20 UNC-2A Thread Description: 1-9/32” - 12 STUB ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size - Bolted (TCP Threaded): 568-214 (568-215) ENGLISH METRIC Nominal Gun Outside Diameter: 1.563 in. 39.7 mm Nominal Gun Body Wall Thickness: .172 in. 4.37 mm Maximum Shot Density: 6 spf 19 spm Angular Phasing - Charge to Charge: 15º 15º Angular Phasing - Bank to Bank: 15º 15º Vertical Charge Spacing: 2.00 in. 50.8 mm Vertical Planes Perforated per Repeat Shot Pattern: 3 3 Horizontal Planes Perforated per Repeat Shot Pattern: 4 4 Minimum Recommended Cord Velocity Of Detonation: 22,000 ft/sec 6,700 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 15,000 psi 103.43 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 1.187 in. (10 in.) 30.15 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0320 or 0220*)-A04-L615 (18 shots) 45 in. (48 in.*) 1.14 m (1.22 m*) Gun Assy (0320 or 0220*)-A07-L615 (36 shots) 81 in. (84 in.*) 2.06 m (2.13 m*) Gun Assy (0320 or 0220*)-A11-L615 (60 shots) 129 in. (132 in.*) 3.28 m (3.35 m*) Gun Assy (0320 or 0220*)-A21-L615 (120 shots) 249 in. (252 in.*) 6.32 m (6.40 m*) Tandem Shoulder Length – W/L Bolted, Threaded (TCP Grooved): .50, 1.25 in. (2.50 in.) 12.70, 31.75 mm (63.50 mm) Gun End to Center of First Scallop Distance: 5.50 in. 139.74 mm Calculated Tensile Strength - Bolted (Threaded) (8): 35,000 lbs. (80,000 lbs.) 155,750 N (356,000 N) Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Tubing Size (9): 2-3/8 in. 60.30 mm

Minimum Recommended Tubing Weight (9): 4.00 lbs/ft 5.96 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry): NOT RECOMMENDED NOT RECOMMENDED Maximum (Average) Test Gun Swell @ RDX (10): NOT RECOMMENDED NOT RECOMMENDED Maximum Charge Explosive Load - Ambient Fluid (Wet): T.B.D. (11) T.B.D. (11) Maximum (Average) Test Gun Swell @ 3.2g RDX (10): T.B.D. (11) T.B.D. (11) Minimum Recommended I.D. Running Restriction: 1.78 in. 45.21 mm Minimum Recommended Washover Pipe Clearance Requirements:











Vertical Drop Test (13): T.B.D. (11) T.B.D. (11) Horizontal Drop Test (13): T.B.D. (11) T.B.D. (11)

Estimated Gun Assy Weight without Explosives: 2.45 lbs/ft 3.64 kg/m Estimated Gun Assy Weight with DP Charge (14): 2.72 lbs/ft 4.06 kg/m 041620080826


















2.03” RETRIEVABLE, THRU-TUBING GUN

4 SPF - 0º PHASE

Charge Arrangement: LOW SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, Cold Drawn, Seamless Steel Tubing Gun Body Configuration: Bolted (or Threaded) & Scalloped Charge Positioning Method: Flat Strip or Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point:

Gun Series 0321 (0222) – W/L Bolted (Threaded) BOTTOM Fired Gun Series 0222 - TCP Threaded Style TOP Fired

Recommended Detonating Cord: 40 grains/foot, FLAT RIBBON Bolted RTG Thread Description: 5/16-18 UNC-2A Threaded RTG Thread Description: 1-11/16” - 8 STUB ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size - Bolted (TCP Threaded): 568-220 (568-221) ENGLISH METRIC Nominal Gun Outside Diameter: 2.03 in. 51.6 mm Nominal Gun Body Wall Thickness: .215 in. 5.46 mm Maximum Shot Density: 4 spf 13 spm Angular Phasing - Charge to Charge: 0º 0º Angular Phasing - Bank to Bank: 0º 0º Vertical Charge Spacing: 3.00 in. 76.2 mm Vertical Planes Perforated per Repeat Shot Pattern: 1 1 Horizontal Planes Perforated per Repeat Shot Pattern: 1 1 Minimum Recommended Cord Velocity Of Detonation: 21,000 ft/sec 6,400 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 17,000 psi 117.22 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 1.578 in. (10 in.) 40.08 mm (254 mm) Standard Overall Gun Lengths (7):

Gun Assy (0321 or 0222*)-A04-041 (12 shots) 45 in. (48 in.*) 1.14 m (1.22 m*) Gun Assy (0321 or 0222*)-A07-041 (24 shots) 81 in. (84 in.*) 2.06 m (2.13 m*) Gun Assy (0321 or 0222*)-A11-041 (40 shots) 129 in. (132 in.*) 3.28 m (3.35 m*) Gun Assy (0321 or 0222*)-A21-041 (80 shots) 249 in. (252 in.*) 6.32 m (6.40 m*)

Tandem Shoulder Length – W/L Bolted, Threaded (TCP Grooved): .50, 1.25 in. (2.50 in.) 12.70, 31.75 mm (63.50 mm) Gun End to Center of First Scallop Distance: 6.00 in. 152.40 mm Calculated Tensile Strength - Bolted (Threaded) (8): 55,000 lbs. (135,000 lbs.) 244,640 N (600,480 N) Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Tubing Size (9): 2-7/8 in. 73.03 mm Minimum Recommended Tubing Weight (9): 6.40 lbs/ft 9.54 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry): 6.5g RDX/HMX 6.5g RDX/HMX Maximum (Average) Test Gun Swell @ 6.5g RDX (10): 2.195 in. (2.184 in.) 55.75 mm (55.47 mm) Maximum Charge Explosive Load - Ambient Fluid (Wet): 6.5g RDX/HMX 6.5g RDX/HMX Maximum (Average) Test Gun Swell @ 6.5g RDX (10): 2.162 in. (2.152 in.) 54.91 mm (54.66 mm) Minimum Recommended I.D. Running Restriction: 2.25 in. 57.15 mm Minimum Recommended Washover Pipe Clearance Requirements:






4 SPF - 60º PHASE

Charge Arrangement: LOW SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, Cold Drawn, Seamless Steel Tubing Gun Body Configuration: Bolted (or Threaded) & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point:










4 SPF - 90º PHASE











4 SPF - 120º PHASE











4 SPF - 180º PHASE











6 SPF - 0º PHASE

Charge Arrangement: MEDIUM SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, Cold Drawn, Seamless Steel Tubing Gun Body Configuration: Bolted (or Threaded) & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point:




Tandem Shoulder Length – W/L Bolted, Threaded (TCP Grooved): .50, 1.25 in. (2.50 in.) 12.70, 31.75 mm (63.50 mm) Gun End to Center of First Scallop Distance: 5.50 in. 139.70 mm Calculated Tensile Strength - Bolted (Threaded) (8): 55,000 lbs. (135,000 lbs.) 244,640 N (600,480 N) Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Tubing Size (9): 2-7/8 in. 73.03 mm Minimum Recommended Tubing Weight (9): 6.40 lbs/ft 9.54 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry): NOT RECOMMENDED NOT RECOMMENDED Maximum (Average) Test Gun Swell @ 6.5g RDX (10): NOT RECOMMENDED NOT RECOMMENDED Maximum Charge Explosive Load - Ambient Fluid (Wet): 6.5g RDX/HMX 6.5g RDX/HMX Maximum (Average) Test Gun Swell @ 6.5g RDX (10): 2.193 in. (2.163 in.) 55.70 mm (54.94 mm) Minimum Recommended I.D. Running Restriction: 2.25 in. 57.15 mm Minimum Recommended Washover Pipe Clearance Requirements:






6 SPF - 60º PHASE





Tandem Shoulder Length – W/L Bolted, Threaded (TCP Grooved): .50, 1.25 in. (2.50 in.) 12.70, 31.75 mm (63.50 mm) Gun End to Center of First Scallop Distance: 5.50 in. 139.70 mm Calculated Tensile Strength - Bolted (Threaded) (8): 55,000 lbs. (135,000 lbs.) 244,640 N (600,480 N) Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Tubing Size (9): 2-7/8 in. 73.03 mm Minimum Recommended Tubing Weight (9): 6.40 lbs/ft 9.54 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry): NOT RECOMMENDED NOT RECOMMENDED Maximum (Average) Test Gun Swell @ 6.5g RDX (10): NOT RECOMMENDED NOT RECOMMENDED Maximum Charge Explosive Load - Ambient Fluid (Wet): 6.5g RDX/HMX 6.5g RDX/HMX Maximum (Average) Test Gun Swell @ 6.5g RDX (10): 2.168 in. (2.161 in.) 55.07 mm (54.89 mm) Minimum Recommended I.D. Running Restriction: 2.25 in. 57.15 mm Minimum Recommended Washover Pipe Clearance Requirements:






8 SPF - 90º PHASE















Gun Assy (0321 or 0222*)-A04-D415 (12 shots) 45 in. (48 in.*) 1.14 m (1.22 m*) Gun Assy (0321 or 0222*)-A07-D415 (24 shots) 81 in. (84 in.*) 2.06 m (2.13 m*) Gun Assy (0321 or 0222*)-A11-D415 (40 shots) 129 in. (132 in.*) 3.28 m (3.35 m*) Gun Assy (0321 or 0222*)-A21-D415 (80 shots) 249 in. (252 in.*) 6.32 m (6.40 m*)

Tandem Shoulder Length – W/L Bolted, Threaded (TCP Grooved): .50, 1.25 in. (2.50 in.) 12.70, 31.75 mm (63.50 mm) Gun End to Center of First Scallop Distance: 6.00 in. 152.40 mm Calculated Tensile Strength - Bolted (Threaded) (8): 55,000 lbs. (135,000 lbs.) 244,640 N (600,480 N) Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Tubing Size (9): 2-7/8 in. 73.03 mm Minimum Recommended Tubing Weight (9): 6.40 lbs/ft 9.54 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry): 6.5g RDX/HMX 6.5g RDX/HMX Maximum (Average) Test Gun Swell @ 6.5g RDX (10): T.B.D. (11) T.B.D. (11) Maximum Charge Explosive Load - Ambient Fluid (Wet): 6.5g RDX/HMX 6.5g RDX/HMX Maximum (Average) Test Gun Swell @ 6.5g RDX (10): T.B.D. (11) T.B.D. (11) Minimum Recommended I.D. Running Restriction: 2.25 in. 57.15 mm Minimum Recommended Washover Pipe Clearance Requirements:











































Gun Assy (0321 or 0222*)-A04-L415 (12 shots) 45 in. (48 in.*) 1.14 m (1.22 m*) Gun Assy (0321 or 0222*)-A07-L415 (24 shots) 81 in. (84 in.*) 2.06 m (2.13 m*) Gun Assy (0321 or 0222*)-A11-L415 (40 shots) 129 in. (132 in.*) 3.28 m (3.35 m*) Gun Assy (0321 or 0222*)-A21-L415 (80 shots) 249 in. (252 in.*) 6.32 m (6.40 m*)













































Tandem Shoulder Length – W/L Bolted, Threaded (TCP Grooved): .50, 1.25 in. (2.50 in.) 12.70, 31.75 mm (63.50 mm) Gun End to Center of First Scallop Distance: 5.50 in. 139.70 mm Calculated Tensile Strength - Bolted (Threaded) (8): 55,000 lbs. (135,000 lbs.) 244,640 N (600,480 N) Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Tubing Size (9): 2-7/8 in. 73.03 mm Minimum Recommended Tubing Weight (9): 6.40 lbs/ft 9.54 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry): NOT RECOMMENDED NOT RECOMMENDED Maximum (Average) Test Gun Swell @ 6.5g RDX (10): NOT RECOMMENDED NOT RECOMMENDED Maximum Charge Explosive Load - Ambient Fluid (Wet): 6.5g RDX/HMX 6.5g RDX/HMX Maximum (Average) Test Gun Swell @ 6.5g RDX (10): T.B.D. (11) T.B.D. (11) Minimum Recommended I.D. Running Restriction: 2.25 in. 57.15 mm Minimum Recommended Washover Pipe Clearance Requirements:



















































































4 SPF - 0º PHASE


Gun Series 0328 - Wireline Bolted Style BOTTOM Fired Gun Series 0228 - TCP Threaded Style TOP Fired

Recommended Detonating Cord: 40 grains/foot, FLAT RIBBON Bolted RTG Thread Description: 3/8 -24 UNC-2A Threaded RTG Thread Description: 2-1/8” - 8 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size - Bolted (TCP Threaded): 568-224 (568-225) ENGLISH METRIC Nominal Gun Outside Diameter: 2.50 in. 63.5 mm Nominal Gun Body Wall Thickness: .250 in. 6.35 mm Maximum Shot Density: 4 spf 13 spm Angular Phasing - Charge to Charge: 0º 0º Angular Phasing - Bank to Bank: 0º 0º Vertical Charge Spacing: 3.00 in. 76.2 mm Vertical Planes Perforated per Repeat Shot Pattern: 1 1 Horizontal Planes Perforated per Repeat Shot Pattern: 1 1 Minimum Recommended Cord Velocity Of Detonation: 21,000 ft/sec 6,400 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 13,000 psi 89.64 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 1.970 in. (10 in.) 50.04 mm (254 mm) Standard Overall Gun Lengths (7):


Tandem Shoulder Length – W/L Bolted, Threaded (TCP Grooved): .50, 1.25 in. (3.25 in.) 12.70, 31.75 mm (82.55 mm) Gun End to Center of First Scallop Distance – Bolted (Threaded): 7.00 in. (7.50 in.) 177.80 mm (190.50 mm) Calculated Tensile Strength - Bolted (Threaded) (8): 80,000 lbs. (80,000 lbs.) 355,800 N (355,800 N) Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Tubing Size (9): 3-1/2 in. 88.90 mm Minimum Recommended Tubing Weight (9): 7.70 lbs/ft 11.48 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry): NOT RECOMMENDED NOT RECOMMENDED Maximum (Average) Test Gun Swell @ RDX (10): NOT RECOMMENDED NOT RECOMMENDED Maximum Charge Explosive Load - Ambient Fluid (Wet): T.B.D. (11) T.B.D. (11) Maximum (Average) Test Gun Swell @ RDX (10): T.B.D. (11) T.B.D. (11) Minimum Recommended I.D. Running Restriction: 2.71 in. 68.83 mm Minimum Recommended Washover Pipe Clearance Requirements:






4 SPF - 60º PHASE





Tandem Shoulder Length – W/L Bolted, Threaded (TCP Grooved): .50, 1.25 in. (3.25 in.) 12.70, 31.75 mm (82.55 mm) Gun End to Center of First Scallop Distance – Bolted (Threaded): 7.00 in. (7.50 in.) 177.80 mm (190.50 mm) Calculated Tensile Strength - Bolted (Threaded) (8): 80,000 lbs. (80,000 lbs.) 355,800 N (355,800 N) Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Tubing Size (9): 3-1/2 in. 88.90 mm Minimum Recommended Tubing Weight (9): 7.70 lbs/ft 11.48 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry): 11.0g RDX/HMX 11.0g RDX/HMX Maximum (Average) Test Gun Swell @ RDX (10): T.B.D. (11) T.B.D. (11) Maximum Charge Explosive Load - Ambient Fluid (Wet): 11.0g RDX/HMX 11.0g RDX/HMX Maximum (Average) Test Gun Swell @ RDX (10): T.B.D. (11) T.B.D. (11) Minimum Recommended I.D. Running Restriction: 2.71 in. 68.83 mm Minimum Recommended Washover Pipe Clearance Requirements:






4 SPF - 90º PHASE











4 SPF - 120º PHASE











4 SPF - 180º PHASE





Tandem Shoulder Length – W/L Bolted, Threaded (TCP Grooved): .50, 1.25 in. (3.25 in.) 12.70, 31.75 mm (82.55 mm) Gun End to Center of First Scallop Distance – Bolted (Threaded): 7.00 in. (7.50 in.) 177.80 mm (190.50 mm) Calculated Tensile Strength - Bolted (Threaded) (8): 80,000 lbs. (80,000 lbs.) 355,800 N (355,800 N) Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Tubing Size (9): 3-1/2 in. 88.90 mm Minimum Recommended Tubing Weight (9): 7.70 lbs/ft 11.48 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry): 11.0g RDX/HMX 11.0g RDX/HMX Maximum (Average) Test Gun Swell @ 11.0g RDX (10): 2.661 in. (2.651 in.) 67.59 mm (67.34 mm) Maximum Charge Explosive Load - Ambient Fluid (Wet): 11.0g RDX/HMX 11.0g RDX/HMX Maximum

(Average) Test Gun Swell @ 11.0g RDX (10): 2.632 in. (2.622 in.) 66.9 mm (66.6 mm) Minimum Recommended I.D. Running Restriction: 2.71 in. 68.83 mm Minimum Recommended Washover Pipe Clearance Requirements:






6 SPF - 0º PHASE











6 SPF - 60º PHASE





Tandem Shoulder Length – W/L Bolted, Threaded (TCP Grooved): .50, 1.25 in. (3.25 in.) 12.70, 31.75 mm (82.55 mm) Gun End to Center of First Scallop Distance – Bolted (Threaded): 6.50 in. (7.00 in.) 165.10 mm (177.80 mm) Calculated Tensile Strength - Bolted (Threaded) (8): 80,000 lbs. (80,000 lbs.) 355,800 N (355,800 N) Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Tubing Size (9): 3-1/2 in. 88.90 mm Minimum Recommended Tubing Weight (9): 7.70 lbs/ft 11.48 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry): NOT RECOMMENDED NOT RECOMMENDED Maximum (Average) Test Gun Swell @ RDX (10): NOT RECOMMENDED NOT RECOMMENDED Maximum Charge Explosive Load - Ambient Fluid (Wet): 11.0g RDX/HMX 11.0g RDX/HMX Maximum (Average) Test Gun Swell @ 11.0g RDX (10): 2.724 in. (2.677 in.) 69.19 mm (68.99 mm) Minimum Recommended I.D. Running Restriction: 2.71 in. 68.83 mm Minimum Recommended Washover Pipe Clearance Requirements:

































Tandem Shoulder Length – W/L Bolted, Threaded (TCP Grooved): .50, 1.25 in. (3.25 in.) 12.70, 31.75 mm (82.55 mm) Gun End to Center of First Scallop Distance – Bolted (Threaded): 7.00 in. (7.50 in.) 177.80 mm (190.50 mm) Calculated Tensile Strength - Bolted (Threaded) (8): 80,000 lbs. (80,000 lbs.) 355,800 N (355,800 N) Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Tubing Size (9): 3-1/2 in. 88.90 mm Minimum Recommended Tubing Weight (9): 7.70 lbs/ft 11.48 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry): NOT RECOMMENDED NOT RECOMMENDED Maximum (Average) Test Gun Swell @ RDX (10): NOT RECOMMENDED NOT RECOMMENDED Maximum Charge Explosive Load - Ambient Fluid (Wet): 11.0g RDX/HMX 11.0g RDX/HMX Maximum

(Average) Test Gun Swell @ 11.0g RDX (10): T.B.D. (11) T.B.D. (11) Minimum Recommended I.D. Running Restriction: 2.71 in. 68.83 mm Minimum Recommended Washover Pipe Clearance Requirements:











Tandem Shoulder Length – W/L Bolted, Threaded (TCP Grooved): .50, 1.25 in. (3.25 in.) 12.70, 31.75 mm (82.55 mm) Gun End to Center of First Scallop Distance – Bolted (Threaded): 7.00 in. (7.50 in.) 177.80 mm (190.50 mm) Calculated Tensile Strength - Bolted (Threaded) (8): 80,000 lbs. (80,000 lbs.) 355,800 N (355,800 N) Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Tubing Size (9): 3-1/2 in. 88.90 mm Minimum Recommended Tubing Weight (9): 7.70 lbs/ft 11.48 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry): NOT RECOMMENDED NOT RECOMMENDED Maximum (Average) Test Gun Swell @ RDX (10): NOT RECOMMENDED NOT RECOMMENDED Maximum Charge Explosive Load - Ambient Fluid (Wet): 11.0g RDX/HMX 11.0g RDX/HMX Maximum (Average) Test Gun Swell @ 11.0g RDX (10): T.B.D. (11) T.B.D. (11) Minimum Recommended I.D. Running Restriction: 2.71 in. 68.83 mm Minimum Recommended Washover Pipe Clearance Requirements:


















































GENERAL COMMENTS Retrievable, Thru-tubing Gun Systems












only. 9. The minimum tubing size/weight recommendation assumes that the tubing is in good condition and properly

supported. 10. Maximum and average gun swell measurements shown herein were taken from laboratory guns containing steel


11. T.B.D. is an acronym for “To Be Determined”. 12. N/A is an acronym for “Not Applicable”. 13. Vertical and horizontal drop test data contained herein does not imply that a gun is safe to run down hole if





2 3/4” EXPENDABLE HOLLOW CARRIER CASING GUN

4 SPF - 0º PHASE

Charge Arrangement: LOW SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point:

Gun Series 0362 - Wireline Style BOTTOM Fired Gun Series 0462 - TCP Style TOP Fired

Recommended Detonating Cord: 80 grains/foot Thread Description: 2-3/8” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-227 ENGLISH METRIC Nominal Gun Outside Diameter: 2.75 in. 69.85 mm Nominal Gun Body Wall Thickness: .313 in. 7.95 mm Maximum Shot Density: 4 spf 13 spm Angular Phasing - Charge to Charge: 0º 0º Angular Phasing - Bank to Bank: 0º 0º Vertical Charge Spacing: 3.00 in. 76.2 mm Vertical Planes Perforated per Repeat Shot Pattern: 1 1 Horizontal Planes Perforated per Repeat Shot Pattern: 1 1 Minimum Recommended Cord Velocity Of Detonation: 21,000 ft/sec 6,400 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 20,000 psi 137.90 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 2.070 in. (12 in.) 52.58 mm (304.8 mm) Standard Overall Gun Lengths (7):

Gun Assy (0362 or 0462)-B04-041 (12 shots) 48 in. 1.22 m Gun Assy (0362 or 0462)-B07-041 (24 shots) 84 in. 2.13 m Gun Assy (0362 or 0462)-B11-041 (40 shots) 132 in. 3.35 m Gun Assy (0362 or 0462)-B21-041 (80 shots) 252 in. 6.40 m

Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to First Scallop Distance: 7.50 in. 190.50 mm Calculated Break Point Tensile Strength - Hardware Only (8): 210,000 lbs. 934,000 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 4-1/2 in. 114.3 mm Minimum Recommended Casing Weight: 9.5 lbs/ft 14.16 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Minimum Recommended I.D. Running Restriction: 3.00 in. 76.2 mm Minimum Recommended Washover Pipe Clearance Requirements:

Casing Drift Diameter-to-Nominal Washover Pipe O.D. .375 in. 9.53 mm Washover Pipe Drift Diameter-to-Nominal Gun O.D. .313 in. 7.95 mm

Vertical Drop Test (14): T.B.D. (12) T.B.D. (12) Horizontal Drop Test (14): T.B.D. (12) T.B.D. (12) Estimated Gun Assy Weight without Explosives: 7.0 lbs/ft 10.4 kg/m Estimated Gun Assy Weight with DP or BH Charges (15): 8.45 lbs/ft 12.8 kg/m 111320071134



4 SPF - 60º PHASE





Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to First Scallop Distance: 7.50 in. 190.50 mm Calculated Break Point Tensile Strength - Hardware Only (8): 210,000 lbs. 934,000 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 4-1/2 in. 114.3 mm Minimum Recommended Casing Weight: 9.5 lbs/ft 14.16 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ 15g RDX (11): 2.834 in. (2.825 in.) 71.98 mm (71.76 mm) Minimum Recommended I.D. Running Restriction: 3.00 in. 76.2 mm Minimum Recommended Washover Pipe Clearance Requirements:





4 SPF - 90º PHASE










4 SPF - 120º PHASE










6 SPF - 60º PHASE

Charge Arrangement: MEDIUM SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point:




Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to First Scallop Distance: 7.00 in. 177.80 mm Calculated Break Point Tensile Strength - Hardware Only (8): 210,000 lbs. 934,000 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 4-1/2 in. 114.3 mm Minimum Recommended Casing Weight: 9.5 lbs/ft 14.16 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): 16.0g RDX/HMX 16.0g RDX/HMX Maximum (Average) Test Gun Swell @ 16.0g RDX (11): 2.979 in. (2.960 in.) 75.7 mm (75.2 mm) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): 18.0g RDX/HMX 18.0g RDX/HMX Maximum (Average) Test Gun Swell @ 18.0g RDX (11): 2.936 in. (2.927 in.) 74.6 mm (74.4 mm) Minimum Recommended I.D. Running Restriction: 3.00 in. 76.2 mm Minimum Recommended Washover Pipe Clearance Requirements:





4 SPF - 60º PHASE



Recommended Detonating Cord: 80 grains/foot Thread Description: 2-3/8” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-227 ENGLISH METRIC Nominal Gun Outside Diameter: 2.88 in. 73.03 mm Nominal Gun Body Wall Thickness: .355 in. 9.02 mm Maximum Shot Density: 4 spf 13 spm Angular Phasing - Charge to Charge: 60º 60º Angular Phasing - Bank to Bank: 60º 60º Vertical Charge Spacing: 3.00 in. 76.2 mm Vertical Planes Perforated per Repeat Shot Pattern: 4 4 Horizontal Planes Perforated per Repeat Shot Pattern: 4 4 Minimum Recommended Cord Velocity Of Detonation: 21,000 ft/sec 6,400 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 25,000 psi 172.37 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 2.102 in. (12 in.) 53.39 mm (305 mm) Standard Overall Gun Lengths (7):


Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to First Scallop Distance: 7.50 in. 190.50 mm Calculated Break Point Tensile Strength - Hardware Only (8): 320,000 lbs. 1,423,430 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 4-1/2 in. 114.3 mm Minimum Recommended Casing Weight: 9.5 lbs/ft 14.16 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Minimum Recommended I.D. Running Restriction: 3.25 in. 82.6 mm Minimum Recommended Washover Pipe Clearance Requirements:





4 SPF - 90º PHASE










6 SPF - 60º PHASE





Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to First Scallop Distance: 7.00 in. 177.80 mm Calculated Break Point Tensile Strength - Hardware Only (8): 320,000 lbs. 1,423,430 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 4-1/2 in. 114.3 mm Minimum Recommended Casing Weight: 9.5 lbs/ft 14.16 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ 16.0g RDX (11): T.B.D. (12) T.B.D. (12) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ 18.0g RDX (11): T.B.D. (12) T.B.D. (12) Minimum Recommended I.D. Running Restriction: 3.25 in. 82.6 mm Minimum Recommended Washover Pipe Clearance Requirements:





4 SPF - 0º PHASE





Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to Center of First Scallop Distance: 7.50 in. 190.50 mm Calculated Break Point Tensile Strength - Hardware Only (8): 235,000 lbs. 1,045,000 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 4-1/2 in. 114.3 mm Minimum Recommended Casing Weight (9): 9.50 lbs/ft 14.16 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): NOT RECOMMENDED NOT RECOMMENDED Maximum (Average) Test Gun Swell @ RDX (11): NOT RECOMMENDED NOT RECOMMENDED Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): 21.0g RDX/HMX 21.0g RDX/HMX Maximum (Average) Test Gun Swell @ 21g RDX (11): 3.455 in. (3.405 in.) 87.76 mm (86.49 mm) Minimum Recommended I.D. Running Restriction: 3.58 in. 90.93 mm Minimum Recommended Washover Pipe Clearance Requirements:


Vertical Drop Test (14): T.B.D. (12) T.B.D. (12) Horizontal Drop Test (14): T.B.D. (12) T.B.D. (12) Estimated Gun Assy Weight without Explosives: 10.4 lbs/ft 15.5 kg/m Estimated Gun Assy Weight with DP Charge (15): 11.0 lbs/ft 16.4 kg/m Estimated Gun Assy Weight with BH Charge (15): T.B.D. (12) T.B.D. (12) 111520070756



4 SPF - 60º PHASE





Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to Center of First Scallop Distance: 7.50 in. 190.50 mm Calculated Break Point Tensile Strength - Hardware Only (8): 235,000 lbs. 1,045,000 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 4-1/2 in. 114.3 mm Minimum Recommended Casing Weight (9): 9.50 lbs/ft 14.16 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Minimum Recommended I.D. Running Restriction: 3.58 in. 90.93 mm Minimum Recommended Washover Pipe Clearance Requirements:





4 SPF - 90º PHASE





Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to Center of First Scallop Distance: 7.50 in. 190.50 mm Calculated Break Point Tensile Strength - Hardware Only (8): 235,000 lbs. 1,045,000 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 4-1/2 in. 114.3 mm Minimum Recommended Casing Weight (9): 9.50 lbs/ft 14.16 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ 21.0g RDX (11): 3.354 in. (3.345 in.) 85.19 mm (84.96 mm) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ 22.7g RDX (11): 3.365 in. (3.354 in) 85.47 mm (85.19 mm) Minimum Recommended I.D. Running Restriction: 3.58 in. 90.93 mm Minimum Recommended Washover Pipe Clearance Requirements:





4 SPF - 120º PHASE





Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to Center of First Scallop Distance: 7.50 in. 190.50 mm Calculated Break Point Tensile Strength - Hardware Only (8): 235,000 lbs. 1,045,000 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 4-1/2 in. 114.3 mm Minimum Recommended Casing Weight (9): 9.50 lbs/ft 14.16 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): NOT RECOMMENDED NOT RECOMMENDED Maximum (Average) Test Gun Swell @ RDX (11): NOT RECOMMENDED NOT RECOMMENDED Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): 21.0g RDX/HMX 21.0g RDX/HMX Maximum (Average) Test Gun Swell @ 21.0g RDX (11): 3.331 in. (3.316 in) 84.61 mm (84.03 mm) Minimum Recommended I.D. Running Restriction: 3.58 in. 90.93 mm Minimum Recommended Washover Pipe Clearance Requirements:





4 SPF - 180º PHASE





Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to Center of First Scallop Distance: 7.50 in. 190.50 mm Calculated Break Point Tensile Strength - Hardware Only (8): 235,000 lbs. 1,045,000 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 4-1/2 in. 114.3 mm Minimum Recommended Casing Weight (9): 9.50 lbs/ft 14.16 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): NOT RECOMMENDED NOT RECOMMENDED Maximum (Average) Test Gun Swell @ RDX (11): NOT RECOMMENDED NOT RECOMMENDED Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Minimum Recommended I.D. Running Restriction: 3.58 in. 90.93 mm Minimum Recommended Washover Pipe Clearance Requirements:





6 SPF - 60º PHASE




Gun Assy (0363 or 0402)-A04-066 (18 shots) 48 in. 1.22 m Gun Assy (0363 or 0402)-A07-066 (36 shots) 84 in. 2.13 m Gun Assy (0363 or 0402)-A11-066 (60 shots) 132 in. 3.35 m Gun Assy (0363 or 0402)-A21-066 (120 shots) 252 in. 6.40 m

Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to Center of First Scallop Distance: 7.00 in. 177.80 mm Calculated Break Point Tensile Strength - Hardware Only (8): 235,000 lbs. 1,045,000 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 4-1/2 in. 114.3 mm Minimum Recommended Casing Weight (9): 9.50 lbs/ft 14.16 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): 21.0g RDX/HMX 21.0g RDX/HMX Maximum (Average) Test Gun Swell @ 22.7g RDX (11): 3.363 in. (3.333 in) 85.4 mm (84.7 mm) (Minimum 500 psi pressure @ 22.7g) Minimum Recommended I.D. Running Restriction: 3.58 in. 90.93 mm Minimum Recommended Washover Pipe Clearance Requirements:


Vertical Drop Test (14): T.B.D. (12) T.B.D. (12) Horizontal Drop Test (14): T.B.D. (12) T.B.D. (12) Estimated Gun Assy Weight without Explosives: 10.4 lbs/ft 15.5 kg/m Estimated Gun Assy Weight with DP or BH Charge (15): 12.4 lbs/ft 18.5 kg/m 111320071457



8 SPF - 135º PHASE




Gun Assy (0363 or 0402)-G04-08D (24 shots) 48 in. 1.22 m Gun Assy (0363 or 0402)-G07-08D (48 shots) 84 in. 2.13 m Gun Assy (0363 or 0402)-G11-08D (80 shots) 132 in. 3.35 m Gun Assy (0363 or 0402)-G21-08D (160 shots) 252 in. 6.40 m

Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to Center of First Scallop Distance: 6.75 in. 171.45 mm Calculated Break Point Tensile Strength - Hardware Only (8): 235,000 lbs. 1,045,000 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 4-1/2 in. 114.3 mm Minimum Recommended Casing Weight (9): 9.50 lbs/ft 14.16 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): 14.0g RDX/HMX 14.0g RDX/HMX Maximum (Average) Test Gun Swell @ 14.0g RDX (11): 3.225 in. (3.208 in.) 81.9 mm (81.5 mm) Minimum Recommended I.D. Running Restriction: 3.58 in. 90.93 mm Minimum Recommended Washover Pipe Clearance Requirements:





12 SPF - 140º PHASE

Charge Arrangement: HIGH SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point:


Recommended Detonating Cord: EXTRA HIGH VELOCITY - 80 grains/foot Thread Description: 2-3/4” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-230 ENGLISH METRIC Nominal Gun Outside Diameter: 3.125 in. 79.38 mm Nominal Gun Body Wall Thickness: .313 in. 7.95 mm Maximum Shot Density: 12 spf 39 spm Angular Phasing - Charge to Charge: 140º 140º Angular Phasing - Bank to Bank: 20º 20º Vertical Charge Spacing: 1.00 in. 25.4 mm Vertical Planes Perforated per Repeat Shot Pattern: 18 18 Horizontal Planes Perforated per Repeat Shot Pattern: 18 18 Minimum Recommended Cord Velocity Of Detonation: 24,750 ft/sec 7,500 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 20,000 psi 137.90 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 2.442 in. (12 in.) 62.03 mm (304.8 mm) Standard Overall Gun Lengths (7):

Gun Assy (0363 or 0402)-G04-12E (36 shots) 48 in. 1.22 m Gun Assy (0363 or 0402)-G07-12E (72 shots) 84 in. 2.13 m Gun Assy (0363 or 0402)-G11-12E (120 shots) 132 in. 3.35 m Gun Assy (0363 or 0402)-G21-12E (240 shots) 252 in. 6.40 m

Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to Center of First Scallop Distance: 6.50 in. 165.10 mm Calculated Break Point Tensile Strength - Hardware Only (8): 235,000 lbs. 1,045,000 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 4-1/2 in. 114.3 mm Minimum Recommended Casing Weight (9): 9.50 lbs/ft 14.16 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): NOT RECOMMENDED NOT RECOMMENDED Maximum (Average) Test Gun Swell @ RDX (11): NOT RECOMMENDED NOT RECOMMENDED Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): 12.0g RDX/HMX 12.0g RDX/HMX Maximum (Average) Test Gun Swell @ 12.0g RDX (11): 3.220 in. (3.187 in.) 81.79 mm (80.95 mm) Minimum Recommended I.D. Running Restriction: 3.58 in. 90.93 mm Minimum Recommended Washover Pipe Clearance Requirements:


Vertical Drop Test (14): T.B.D. (12) T.B.D. (12) Horizontal Drop Test (14): T.B.D. (12) T.B.D. (12) Estimated Gun Assy Weight without Explosives: 10.4 lbs/ft 15.5 kg/m Estimated Gun Assy Weight with DP Charge (15): T.B.D. (12) T.B.D. (12) Estimated Gun Assy Weight with BH Charge (15): 12.5 lbs/ft 18.6 kg/m 0321080753



4 SPF - 0º PHASE





Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to First Scallop Distance: 7.50 in. 190.50 mm Calculated Break Point Tensile Strength - Hardware Only (8): 270,000 lbs. 1,200,000 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 4-1/2 in. 114.3 mm Minimum Recommended Casing Weight: 9.5 lbs/ft 14.16 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): NOT RECOMMENDED NOT RECOMMENDED Maximum (Average) Test Gun Swell @ RDX (11): NOT RECOMMENDED NOT RECOMMENDED Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Minimum Recommended I.D. Running Restriction: 3.80 in. 96.52 mm Minimum Recommended Washover Pipe Clearance Requirements:





4 SPF - 60º PHASE










4 SPF - 90º PHASE





Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to First Scallop Distance: 7.50 in. 190.50 mm Calculated Break Point Tensile Strength - Hardware Only (8): 270,000 lbs. 1,200,000 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 4-1/2 in. 114.3 mm Minimum Recommended Casing Weight: 9.5 lbs/ft 14.16 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): 32.0g RDX/HMX 32.0g RDX/HMX Maximum (Average) Test Gun Swell @ 32.0g RDX (11): 3.631 in. (3.620 in.) 92.2 mm (92.0 mm) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): 36.0g RDX/HMX 36.0g RDX/HMX Maximum (Average) Test Gun Swell @ 36.0g RDX (11): 3.610 in. (3.589 in.) 91.7 mm (91.2 mm) Minimum Recommended I.D. Running Restriction: 3.80 in. 96.52 mm Minimum Recommended Washover Pipe Clearance Requirements:





4 SPF - 120º PHASE










6 SPF - 60º PHASE





Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to First Scallop Distance: 7.00 in. 177.80 mm Calculated Break Point Tensile Strength - Hardware Only (8): 270,000 lbs. 1,200,000 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 4-1/2 in. 114.3 mm Minimum Recommended Casing Weight: 9.5 lbs/ft 14.16 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): 22.0g RDX/HMX 22.0g RDX/HMX Maximum (Average) Test Gun Swell @ 22.0g RDX (11): 3.580 in. (3.566 in.) 90.9 mm (90.6 mm) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): 26.0g RDX/HMX 26.0g RDX/HMX Maximum (Average) Test Gun Swell @ 26.0g RDX (11): 3.617 in. (3.603 in.) 91.9 mm (91.5 mm) Minimum Recommended I.D. Running Restriction: 3.80 in. 96.52 mm Minimum Recommended Washover Pipe Clearance Requirements:





8 SPF - 135º PHASE




Gun Assy (0365 or 0403)-G04-08D (32 shots) 48 in. 1.22 m Gun Assy (0365 or 0403)-G07-08D (48 shots) 84 in. 2.13 m Gun Assy (0365 or 0403)-G11-08D (80 shots) 132 in. 3.35 m Gun Assy (0365 or 0403)-G21-08D (160 shots) 252 in. 6.40 m



Vertical Drop Test (14): T.B.D. (12) T.B.D. (12) Horizontal Drop Test (14): T.B.D. (12) T.B.D. (12) Estimated Gun Assy Weight without Explosives: T.B.D. (12) T.B.D. (12) Estimated Gun Assy Weight with DP or BH Charges (15): T.B.D. (12) T.B.D. (12) 111620070601




Charge Arrangement: HIGH SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point:


Recommended Detonating Cord: EXTRA HIGH VELOCITY - 80 grains/foot Thread Description: 2-13/16” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-231 ENGLISH METRIC Nominal Gun Outside Diameter: 3.375 in. 85.7 mm Nominal Gun Body Wall Thickness: .375 in. 9.53 mm Maximum Shot Density: 12 spf 39 spm Angular Phasing - Charge to Charge: 140º 140º Angular Phasing - Bank to Bank: 20º 20º Vertical Charge Spacing: 1.00 in. 25.4 mm Vertical Planes Perforated per Repeat Shot Pattern: 18 18 Horizontal Planes Perforated per Repeat Shot Pattern: 18 18 Minimum Recommended Cord Velocity Of Detonation: 24,750 ft/sec 7,500 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 20,000 psi 137.90 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 2.590 in. (10 in.) 65.79 mm (254 mm) Standard Overall Gun Lengths (7):

Gun Assy (0365 or 0403)-G04-12E (36 shots) 48 in. 1.22 m Gun Assy (0365 or 0403)-G07-12E (72 shots) 84 in. 2.13 m Gun Assy (0365 or 0403)-G11-12E (120 shots) 132 in. 3.35 m Gun Assy (0365 or 0403)-G21-12E (240 shots) 252 in. 6.40 m



Vertical Drop Test (14): T.B.D. (12) T.B.D. (12) Horizontal Drop Test (14): T.B.D. (12) T.B.D. (12) Estimated Gun Assy Weight without Explosives: 9.82 lbs/ft 14.6 kg/m Estimated Gun Assy Weight with DP Charges (15): T.B.D. (12) T.B.D. (12) Estimated Gun Assy Weight with BH Charges (15): T.B.D. (12) T.B.D. (12) 111620070607



4 SPF - 60º PHASE Charge Arrangement: LOW SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0350 - Wireline Style BOTTOM Fired Gun Series 0415 - TCP Style TOP Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 3” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-334 ENGLISH METRIC Nominal Gun Outside Diameter: 3.50 in. 88.9 mm Nominal Gun Body Wall Thickness: .375 in. 9.53 mm Maximum Shot Density: 4 spf 13 spm Angular Phasing - Charge to Charge: 60º 60º Angular Phasing - Bank to Bank: 60º 60º Vertical Charge Spacing: 3.00 in. 76.2 mm Vertical Planes Perforated per Repeat Shot Pattern: 6 6 Horizontal Planes Perforated per Repeat Shot Pattern: 6 6 Minimum Recommended Cord Velocity Of Detonation: 21,000 ft/sec 6,400 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 23,000 psi 158.59 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 2.700 in. (10 in.) 68.85 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0350 or 0415)-A04-046 (12 shots) 48 in. 1.22 m Gun Assy (0350 or 0415)-A07-046 (24 shots) 84 in. 2.13 m Gun Assy (0350 or 0415)-A11-046 (40 shots) 132 in. 3.35 m Gun Assy (0350 or 0415)-A21-046 (80 shots) 252 in. 6.40 m Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to Center of First Scallop Distance: 7.50 in. 190.50 mm Calculated Break Point Tensile Strength - Hardware Only (8): 350,000 lbs. 1,556,800 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 5.00 in. 127.0 mm Minimum Recommended Casing Weight (9): 11.5 lbs/ft 17.15 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): 36.0g RDX/HMX 36.0g RDX/HMX Maximum (Average) Test Gun Swell @ 36.0g RDX (11): 3.809 in. (3.794 in.) 96.75 mm (96.37 mm) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): T.B.D. (12) T.B.D. (12)

Maximum (Average) Test Gun Swell @ 36.0g RDX (11): 3.726 in. (3.702 in.) 94.64 mm (94.04 mm) Minimum Recommended I.D. Running Restriction: 4.156 in. 105.56 mm Minimum Recommended Washover Pipe Clearance Requirements:


Vertical Drop Test (14): T.B.D. (12) T.B.D. (12) Horizontal Drop Test (14): T.B.D. (12) T.B.D. (12) Estimated Gun Assy Weight without Explosives: 13.3 lbs/ft 19.7 kg/m Estimated Gun Assy Weight with DP Charge (15): T.B.D. (12) T.B.D. (12) Estimated Gun Assy Weight with BH Charge (15): T.B.D. (12) T.B.D. (12) 112120071549



4 SPF - 90º PHASE Charge Arrangement: LOW SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0350 - Wireline Style BOTTOM Fired Gun Series 0415 - TCP Style TOP Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 3” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-334 ENGLISH METRIC Nominal Gun Outside Diameter: 3.50 in. 88.9 mm Nominal Gun Body Wall Thickness: .375 in. 9.53 mm Maximum Shot Density: 4 spf 13 spm Angular Phasing - Charge to Charge: 90º 90º Angular Phasing - Bank to Bank: 90º 90º Vertical Charge Spacing: 3.00 in. 76.2 mm Vertical Planes Perforated per Repeat Shot Pattern: 4 4 Horizontal Planes Perforated per Repeat Shot Pattern: 4 4 Minimum Recommended Cord Velocity Of Detonation: 21,000 ft/sec 6,400 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 23,000 psi 158.59 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 2.700 in. (10 in.) 68.85 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0350 or 0415)-A04-044 (12 shots) 48 in. 1.22 m Gun Assy (0350 or 0415)-A07-044 (24 shots) 84 in. 2.13 m Gun Assy (0350 or 0415)-A11-044 (40 shots) 132 in. 3.35 m Gun Assy (0350 or 0415)-A21-044 (80 shots) 252 in. 6.40 m Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to Center of First Scallop Distance: 7.50 in. 190.50 mm Calculated Break Point Tensile Strength - Hardware Only (8): 350,000 lbs. 1,556,800 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 5.00 in. 127.0 mm Minimum Recommended Casing Weight (9): 11.5 lbs/ft 17.15 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): 36.0g RDX/HMX 36.0g RDX/HMX Maximum (Average) Test Gun Swell @ 36.0g RDX (11): 3.791 in. (3.780 in.) 96.29 mm (96.01 mm) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ 36.0g RDX (11): 3.716 in. (3.706 in.) 94.39 mm (94.13 mm) Minimum Recommended I.D. Running Restriction: 4.156 in. 105.56 mm Minimum Recommended Washover Pipe Clearance Requirements:





5 SPF - 60º PHASE Charge Arrangement: MEDIUM SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0350 - Wireline Style BOTTOM Fired Gun Series 0415 - TCP Style TOP Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 3” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-334 ENGLISH METRIC Nominal Gun Outside Diameter: 3.50 in. 88.9 mm Nominal Gun Body Wall Thickness: .375 in. 9.53 mm Maximum Shot Density: 5 spf 16 spm Angular Phasing - Charge to Charge: 60º 60º Angular Phasing - Bank to Bank: 60º 60º Vertical Charge Spacing: 2.40 in. 60.96 mm Vertical Planes Perforated per Repeat Shot Pattern: 5 5 Horizontal Planes Perforated per Repeat Shot Pattern: 5 5 Minimum Recommended Cord Velocity Of Detonation: 22,000 ft/sec 6,700 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 23,000 psi 158.59 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 2.700 in. (10 in.) 68.85 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0350 or 0415)-A04-056 (15 shots) 48 in. 1.22 m Gun Assy (0350 or 0415)-A07-056 (30 shots) 84 in. 2.13 m Gun Assy (0350 or 0415)-A11-056 (50 shots) 132 in. 3.35 m Gun Assy (0350 or 0415)-A21-056 (100 shots) 252 in. 6.40 m Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to Center of First Scallop Distance: 7.20 in. 182.88 mm Calculated Break Point Tensile Strength - Hardware Only (8): 350,000 lbs. 1,556,800 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 5.00 in. 127.0 mm Minimum Recommended Casing Weight (9): 11.5 lbs/ft 17.15 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): 32.0g RDX/HMX 32.0g RDX/HMX Maximum (Average) Test Gun Swell @ 32.0g RDX (11): 3.803 in. (3.782 in.) 96.60 mm (96.06 mm) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ 32.0g RDX (11): 3.729 in. (3.651 in.) 94.72 mm (92.74 mm) Minimum Recommended I.D. Running Restriction: 4.156 in. 105.56 mm Minimum Recommended Washover Pipe Clearance Requirements:





6 SPF - 60º PHASE Charge Arrangement: MEDIUM SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0350 - Wireline Style BOTTOM Fired Gun Series 0415 - TCP Style TOP Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 3” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-334 ENGLISH METRIC Nominal Gun Outside Diameter: 3.50 in. 88.9 mm Nominal Gun Body Wall Thickness: .375 in. 9.53 mm Maximum Shot Density: 6 spf 19 spm Angular Phasing - Charge to Charge: 60º 60º Angular Phasing - Bank to Bank: 60º 60º Vertical Charge Spacing: 2.00 in. 50.80 mm Vertical Planes Perforated per Repeat Shot Pattern: 6 6 Horizontal Planes Perforated per Repeat Shot Pattern: 6 6 Minimum Recommended Cord Velocity Of Detonation: 22,000 ft/sec 6,700 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 23,000 psi 158.59 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 2.700 in. (10 in.) 68.85 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0350 or 0415)-B04-066 (18 shots) 48 in. 1.22 m Gun Assy (0350 or 0415)-B07-066 (36 shots) 84 in. 2.13 m Gun Assy (0350 or 0415)-B11-066 (60 shots) 132 in. 3.35 m Gun Assy (0350 or 0415)-B21-066 (120 shots) 252 in. 6.40 m Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to Center of First Scallop Distance: 7.00 in. 177.88 mm Calculated Break Point Tensile Strength - Hardware Only (8): 350,000 lbs. 1,556,800 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 5.00 in. 127.0 mm Minimum Recommended Casing Weight (9): 11.5 lbs/ft 17.15 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Minimum Recommended I.D. Running Restriction: 4.156 in. 105.56 mm Minimum Recommended Washover Pipe Clearance Requirements:





8 SPF - 135º PHASE Charge Arrangement: MEDIUM SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0350 - Wireline Style BOTTOM Fired Gun Series 0415 - TCP Style TOP Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 3” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-334 ENGLISH METRIC Nominal Gun Outside Diameter: 3.50 in. 88.9 mm Nominal Gun Body Wall Thickness: .375 in. 9.53 mm Maximum Shot Density: 8 spf 26 spm Angular Phasing - Charge to Charge: 135º 135º Angular Phasing - Bank to Bank: 135º 135º Vertical Charge Spacing: 2.40 in. 60.96 mm Vertical Planes Perforated per Repeat Shot Pattern: 8 8 Horizontal Planes Perforated per Repeat Shot Pattern: 8 8 Minimum Recommended Cord Velocity Of Detonation: 22,000 ft/sec 6,700 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 22,000 psi 151.69 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 2.700 in. (10 in.) 68.85 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0350 or 0415)-G04-08D (24 shots) 48 in. 1.22 m Gun Assy (0350 or 0415)-G07-08D (48 shots) 84 in. 2.13 m Gun Assy (0350 or 0415)-G11-08D (80 shots) 132 in. 3.35 m Gun Assy (0350 or 0415)-G21-08D (160 shots) 252 in. 6.40 m Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to Center of First Scallop Distance: 6.75 in. 171.45 mm Calculated Break Point Tensile Strength - Hardware Only (8): 350,000 lbs. 1,556,800 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 5.00 in. 127.0 mm Minimum Recommended Casing Weight (9): 11.5 lbs/ft 17.15 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Minimum Recommended I.D. Running Restriction: 4.156 in. 105.56 mm Minimum Recommended Washover Pipe Clearance Requirements:




4” EXPENDABLE HOLLOW CARRIER CASING GUN

4 SPF - 0º PHASE

Charge Arrangement: LOW SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0400 - Wireline Style BOTTOM Fired Gun Series 0404 - TCP Style TOP Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 3 7/16” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-236 ENGLISH METRIC Nominal Gun Outside Diameter: 4.00 in. 101.6 mm Nominal Gun Body Wall Thickness: .375 in. 9.53 mm Maximum Shot Density: 4 spf 13 spm Angular Phasing - Charge to Charge: 0º 0º Angular Phasing - Bank to Bank: 0º 0º Vertical Charge Spacing: 3.00 in. 76.2 mm Vertical Planes Perforated per Repeat Shot Pattern: 1 1 Horizontal Planes Perforated per Repeat Shot Pattern: 1 1 Minimum Recommended Cord Velocity Of Detonation: 21,000 ft/sec 6,400 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 15,700 psi 108.25 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 3.200 in. (10 in.) 81.28 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0400 or 0404)-A04-041 (12 shots) 48 in. 1.22 m Gun Assy (0400 or 0404)-A07-041 (24 shots) 84 in. 2.13 m Gun Assy (0400 or 0404)-A11-041 (40 shots) 132 in. 3.35 m Gun Assy (0400 or 0404)-A21-041 (80 shots) 252 in. 6.40 m Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to First Scallop Distance: 7.50 in. 190.50 mm Calculated Break Point Tensile Strength - Hardware Only (8): 450,000 lbs. 2,001,600 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 5-1/2 in. 139.7 mm Minimum Recommended Casing Weight (9): 14.0 lbs/ft 20.85 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): NOT RECOMMENDED NOT RECOMMENDED Maximum (Average) Test Gun Swell @ RDX (11): NOT RECOMMENDED NOT RECOMMENDED Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Minimum Recommended I.D. Running Restriction: 4.375 in. 111.13 mm Minimum Recommended Washover Pipe Clearance Requirements:





4 SPF - 60º PHASE

Charge Arrangement: LOW SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0400 - Wireline Style BOTTOM Fired Gun Series 0404 - TCP Style TOP Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 3 7/16” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-236 ENGLISH METRIC Nominal Gun Outside Diameter: 4.00 in. 101.6 mm Nominal Gun Body Wall Thickness: .375 in. 9.53 mm Maximum Shot Density: 4 spf 13 spm Angular Phasing - Charge to Charge: 60º 60º Angular Phasing - Bank to Bank: 60º 60º Vertical Charge Spacing: 3.00 in. 76.2 mm Vertical Planes Perforated per Repeat Shot Pattern: 6 6 Horizontal Planes Perforated per Repeat Shot Pattern: 6 6 Minimum Recommended Cord Velocity Of Detonation: 21,000 ft/sec 6,400 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 20,000 psi 137.90 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 3.200 in. (10 in.) 81.28 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0400 or 0404)-A04-046 (12 shots) 48 in. 1.22 m Gun Assy (0400 or 0404)-A07-046 (24 shots) 84 in. 2.13 m Gun Assy (0400 or 0404)-A11-046 (40 shots) 132 in. 3.35 m Gun Assy (0400 or 0404)-A21-046 (80 shots) 252 in. 6.40 m Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to First Scallop Distance: 7.50 in. 190.50 mm Calculated Break Point Tensile Strength - Hardware Only (8): 450,000 lbs. 2,001,600 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 5-1/2 in. 139.7 mm Minimum Recommended Casing Weight (9): 14.0 lbs/ft 20.85 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Minimum Recommended I.D. Running Restriction: 4.375 in. 111.13 mm Minimum Recommended Washover Pipe Clearance Requirements:





4 SPF - 90º PHASE

Charge Arrangement: LOW SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0400 - Wireline Style BOTTOM Fired Gun Series 0404 - TCP Style TOP Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 3 7/16” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-236 ENGLISH METRIC Nominal Gun Outside Diameter: 4.00 in. 101.6 mm Nominal Gun Body Wall Thickness: .375 in. 9.53 mm Maximum Shot Density: 4 spf 13 spm Angular Phasing - Charge to Charge: 90º 90º Angular Phasing - Bank to Bank: 90º 90º Vertical Charge Spacing: 3.00 in. 76.2 mm Vertical Planes Perforated per Repeat Shot Pattern: 4 4 Horizontal Planes Perforated per Repeat Shot Pattern: 4 4 Minimum Recommended Cord Velocity Of Detonation: 21,000 ft/sec 6,400 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 20,000 psi 137.90 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 3.200 in. (10 in.) 81.28 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0400 or 0404)-A04-044 (12 shots) 48 in. 1.22 m Gun Assy (0400 or 0404)-A07-044 (24 shots) 84 in. 2.13 m Gun Assy (0400 or 0404)-A11-044 (40 shots) 132 in. 3.35 m Gun Assy (0400 or 0404)-A21-044 (80 shots) 252 in. 6.40 m Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to First Scallop Distance: 7.50 in. 190.50 mm Calculated Break Point Tensile Strength - Hardware Only (8): 450,000 lbs. 2,001,600 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 5-1/2 in. 139.7 mm Minimum Recommended Casing Weight (9): 14.0 lbs/ft 20.85 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): 40.0g RDX/HMX 40.0g RDX/HMX Maximum (Average) Test Gun Swell @ 39.0g RDX (11): 4.343 in. (4.314 in.) 110.31 mm (109.58 mm) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): 44.0g RDX/HMX 44.0g RDX/HMX Maximum (Average) Test Gun Swell @ 39.0g RDX (11): 4.226 in. (4.213 in.) 107.34 mm (107.01 mm) Minimum Recommended I.D. Running Restriction: 4.375 in. 111.13 mm Minimum Recommended Washover Pipe Clearance Requirements:





4 SPF - 120º PHASE

Charge Arrangement: LOW SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0400 - Wireline Style BOTTOM Fired Gun Series 0404 - TCP Style TOP Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 3 7/16” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-236 ENGLISH METRIC Nominal Gun Outside Diameter: 4.00 in. 101.6 mm Nominal Gun Body Wall Thickness: .375 in. 9.53 mm Maximum Shot Density: 4 spf 13 spm Angular Phasing - Charge to Charge: 120º 120º Angular Phasing - Bank to Bank: 120º 120º Vertical Charge Spacing: 3.00 in. 76.2 mm Vertical Planes Perforated per Repeat Shot Pattern: 3 3 Horizontal Planes Perforated per Repeat Shot Pattern: 3 3 Minimum Recommended Cord Velocity Of Detonation: 21,000 ft/sec 6,400 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 20,000 psi 137.90 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 3.200 in. (10 in.) 81.28 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0400 or 0404)-A04-043 (12 shots) 48 in. 1.22 m Gun Assy (0400 or 0404)-A07-043 (24 shots) 84 in. 2.13 m Gun Assy (0400 or 0404)-A11-043 (40 shots) 132 in. 3.35 m Gun Assy (0400 or 0404)-A21-043 (80 shots) 252 in. 6.40 m Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to First Scallop Distance: 7.50 in. 190.50 mm Calculated Break Point Tensile Strength - Hardware Only (8): 450,000 lbs. 2,001,600 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 5-1/2 in. 139.7 mm Minimum Recommended Casing Weight (9): 14.0 lbs/ft 20.85 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ 39.0g RDX (11): 4.258 in. (4.241 in.) 108.15 mm (108.72 mm) Minimum Recommended I.D. Running Restriction: 4.375 in. 111.13 mm Minimum Recommended Washover Pipe Clearance Requirements:





4 SPF - 180º PHASE

Charge Arrangement: LOW SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0400 - Wireline Style BOTTOM Fired Gun Series 0404 - TCP Style TOP Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 3 7/16” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-236 ENGLISH METRIC Nominal Gun Outside Diameter: 4.00 in. 101.6 mm Nominal Gun Body Wall Thickness: .375 in. 9.53 mm Maximum Shot Density: 4 spf 13 spm Angular Phasing - Charge to Charge: 180º 180º Angular Phasing - Bank to Bank: 180º 180º Vertical Charge Spacing: 3.00 in. 76.2 mm Vertical Planes Perforated per Repeat Shot Pattern: 2 2 Horizontal Planes Perforated per Repeat Shot Pattern: 2 2 Minimum Recommended Cord Velocity Of Detonation: 21,000 ft/sec 6,400 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 19,500 psi 134.45 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 3.200 in. (10 in.) 81.28 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0400 or 0404)-A04-042 (12 shots) 48 in. 1.22 m Gun Assy (0400 or 0404)-A07-042 (24 shots) 84 in. 2.13 m Gun Assy (0400 or 0404)-A11-042 (40 shots) 132 in. 3.35 m Gun Assy (0400 or 0404)-A21-042 (80 shots) 252 in. 6.40 m Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to First Scallop Distance: 7.50 in. 190.50 mm Calculated Break Point Tensile Strength - Hardware Only (8): 450,000 lbs. 2,001,600 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 5-1/2 in. 139.7 mm Minimum Recommended Casing Weight (9): 14.0 lbs/ft 20.85 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Minimum Recommended I.D. Running Restriction: 4.375 in. 111.13 mm Minimum Recommended Washover Pipe Clearance Requirements:





5 SPF - 60º PHASE

Charge Arrangement: MEDIUM SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0400 - Wireline Style BOTTOM Fired Gun Series 0404 - TCP Style TOP Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 3 7/16” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-236 ENGLISH METRIC Nominal Gun Outside Diameter: 4.00 in. 101.6 mm Nominal Gun Body Wall Thickness: .375 in. 9.53 mm Maximum Shot Density: 5 spf 16 spm Angular Phasing - Charge to Charge: 60º 60º Angular Phasing - Bank to Bank: 60º 60º Vertical Charge Spacing: 2.40 in. 60.96 mm Vertical Planes Perforated per Repeat Shot Pattern: 6 6 Horizontal Planes Perforated per Repeat Shot Pattern: 6 6 Minimum Recommended Cord Velocity Of Detonation: 22,000 ft/sec 6,700 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 20,000 psi 137.90 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 3.200 in. (10 in.) 81.28 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0400 or 0404)-A04-056 (15 shots) 48 in. 1.22 m Gun Assy (0400 or 0404)-A07-056 (30 shots) 84 in. 2.13 m Gun Assy (0400 or 0404)-A11-056 (50 shots) 132 in. 3.35 m Gun Assy (0400 or 0404)-A21-056 (100 shots) 252 in. 6.40 m Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to First Scallop Distance: 7.20 in. 182.88 mm Calculated Break Point Tensile Strength - Hardware Only (8): 450,000 lbs. 2,001,600 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 5-1/2 in. 139.7 mm Minimum Recommended Casing Weight (9): 14.0 lbs/ft 20.85 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ 36.0g RDX (11): 4.331 in. (4.302 in.) 110.01 mm (109.27 mm) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ 36.0g RDX (11): 4.244 in. (4.229 in.) 107.80 mm (107.42 mm) Minimum Recommended I.D. Running Restriction: 4.375 in. 111.13 mm Minimum Recommended Washover Pipe Clearance Requirements:





6 SPF - 60º PHASE

Charge Arrangement: MEDIUM SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0400 - Wireline Style BOTTOM Fired Gun Series 0404 - TCP Style TOP Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 3 7/16” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-236 ENGLISH METRIC Nominal Gun Outside Diameter: 4.00 in. 101.6 mm Nominal Gun Body Wall Thickness: .375 in. 9.53 mm Maximum Shot Density: 6 spf 19 spm Angular Phasing - Charge to Charge: 60º 60º Angular Phasing - Bank to Bank: 60º 60º Vertical Charge Spacing: 2.00 in. 50.8 mm Vertical Planes Perforated per Repeat Shot Pattern: 6 6 Horizontal Planes Perforated per Repeat Shot Pattern: 6 6 Minimum Recommended Cord Velocity Of Detonation: 22,000 ft/sec 6,700 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 20,000 psi 137.90 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 3.200 in. (10 in.) 81.28 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0400 or 0404)-B04-066 (18 shots) 48 in. 1.22 m Gun Assy (0400 or 0404)-B07-066 (36 shots) 84 in. 2.13 m Gun Assy (0400 or 0404)-B11-066 (60 shots) 132 in. 3.35 m Gun Assy (0400 or 0404)-B21-066 (120 shots) 252 in. 6.40 m Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to First Scallop Distance: 7.00 in. 177.80 mm Calculated Break Point Tensile Strength - Hardware Only (8): 450,000 lbs. 2,001,600 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 5-1/2 in. 139.7 mm Minimum Recommended Casing Weight (9): 14.0 lbs/ft 20.85 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Minimum Recommended I.D. Running Restriction: 4.375 in. 111.13 mm Minimum Recommended Washover Pipe Clearance Requirements:





8 SPF - 135º PHASE

Charge Arrangement: MEDIUM SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0400 - Wireline Style BOTTOM Fired Gun Series 0404 - TCP Style TOP Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 3 7/16” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-236 ENGLISH METRIC Nominal Gun Outside Diameter: 4.00 in. 101.6 mm Nominal Gun Body Wall Thickness: .375 in. 9.53 mm Maximum Shot Density: 8 spf 26 spm Angular Phasing - Charge to Charge: 135º 135º Angular Phasing - Bank to Bank: 45º 45º Vertical Charge Spacing: 1.50 in. 38.1 mm Vertical Planes Perforated per Repeat Shot Pattern: 8 8 Horizontal Planes Perforated per Repeat Shot Pattern: 8 8 Minimum Recommended Cord Velocity Of Detonation: 23,000 ft/sec 7,000 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 20,000 psi 137.90 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 3.200 in. (10 in.) 81.28 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0400 or 0404)-1D04-08D (24 shots) 48 in. 1.22 m Gun Assy (0400 or 0404)-1D07-08D (48 shots) 84 in. 2.13 m Gun Assy (0400 or 0404)-1D11-08D (80 shots) 132 in. 3.35 m Gun Assy (0400 or 0404)-1D21-08D (160 shots) 252 in. 6.40 m Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to First Scallop Distance: 6.75 in. 171.45 mm Calculated Break Point Tensile Strength - Hardware Only (8): 450,000 lbs. 2,001,600 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 5-1/2 in. 139.7 mm Minimum Recommended Casing Weight (9): 14.0 lbs/ft 20.85 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): 21.0g RDX/HMX 21.0g RDX/HMX Maximum (Average) Test Gun Swell @ 21.0g RDX (11): 4.260 in. (4.244 in.) 108.2 mm (107.80 mm) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Minimum Recommended I.D. Running Restriction: 4.375 in. 111.13 mm Minimum Recommended Washover Pipe Clearance Requirements:





4 SPF - 90º PHASE

Charge Arrangement: LOW SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0445 - Wireline Style BOTTOM Fired Gun Series 0414 - TCP Style TOP Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 3 15/16” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-342 ENGLISH METRIC Nominal Gun Outside Diameter: 4.50 in. 114.3 mm Nominal Gun Body Wall Thickness: .375 in. 9.53 mm Maximum Shot Density: 4 spf 13 spm Angular Phasing - Charge to Charge: 90º 90º Angular Phasing - Bank to Bank: 90º 90º Vertical Charge Spacing: 3.00 in. 76.20 mm Vertical Planes Perforated per Repeat Shot Pattern: 4 4 Horizontal Planes Perforated per Repeat Shot Pattern: 4 4 Minimum Recommended Cord Velocity Of Detonation: 21,000 ft/sec 6,400 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 19,500 psi 134.45 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 3.696 in. (10 in.) 93.88 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0445 or 0414)-A04-044 (12 shots) 48 in. 1.22 m Gun Assy (0445 or 0414)-A07-044 (24 shots) 84 in. 2.13 m Gun Assy (0445 or 0414)-A11-044 (40 shots) 132 in. 3.35 m Gun Assy (0445 or 0414)-A21-044 (80 shots) 252 in. 6.40 m Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.40 in.) 35.05 mm (60.96 mm) Gun End to First Scallop Distance: 7.50 in. 190.50 mm Calculated Break Point Tensile Strength - Hardware Only (8): 453,000 lbs. 2,015,000 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 6-5/8 in. 168.3 mm Minimum Recommended Casing Weight: (9): 20.0 lbs/ft 29.79 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ 39.0g RDX (11): 4.726 in. (4.717 in.) 120.04 mm (119.81 mm) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ 39.0g RDX (11): 4.705 in. (4.656 in.) 119.51 mm (118.26 mm) Minimum Recommended I.D. Running Restriction: 4.915 in. 124.84 mm Minimum Recommended Washover Pipe Clearance Requirements:





5 SPF - 60º PHASE

Charge Arrangement: MEDIUM SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0445 - Wireline Style BOTTOM Fired Gun Series 0414 - TCP Style TOP Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 3 15/16” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-342 ENGLISH METRIC Nominal Gun Outside Diameter: 4.50 in. 114.3 mm Nominal Gun Body Wall Thickness: .375 in. 9.53 mm Maximum Shot Density: 5 spf 16 spm Angular Phasing - Charge to Charge: 60º 60º Angular Phasing - Bank to Bank: 60º 60º Vertical Charge Spacing: 2.40 in. 61.0 mm Vertical Planes Perforated per Repeat Shot Pattern: 6 6 Horizontal Planes Perforated per Repeat Shot Pattern: 6 6 Minimum Recommended Cord Velocity Of Detonation: 25,000 ft/sec 7,600 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 19,500 psi 134.45 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 3.696 in. (10 in.) 93.88 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0445 or 0414)-1A04-056 (15 shots) 48 in. 1.22 m Gun Assy (0445 or 0414)-1A07-056 (30 shots) 84 in. 2.13 m Gun Assy (0445 or 0414)-1A11-056 (50 shots) 132 in. 3.35 m Gun Assy (0445 or 0414)-1A21-056 (100 shots) 252 in. 6.40 m Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.40 in.) 35.05 mm (60.96 mm) Gun End to First Scallop Distance: 7.20 in. 182.88 mm Calculated Break Point Tensile Strength - Hardware Only (8): 453,000 lbs. 2,015,000 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 6-5/8 in. 168.3 mm Minimum Recommended Casing Weight: (9): 20.0 lbs/ft 29.79 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): 39.0g RDX/HMX (12)

39.0g RDX/HMX Maximum (Average) Test Gun Swell @ 39g RDX (11): 4.810 in. (4.785 in.) 122.17 mm (121.54 mm) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): 39.0g RDX/HMX (12)

39.0g RDX/HMX Maximum (Average) Test Gun Swell @ 39g RDX (11): 4.742 in. (4.678 in.) 120.45 mm (118.82 mm) Minimum Recommended I.D. Running Restriction: 4.915 in. 124.84 mm Minimum Recommended Washover Pipe Clearance Requirements:





6 SPF - 60º PHASE

Charge Arrangement: MEDIUM SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0445 - Wireline Style BOTTOM Fired Gun Series 0414 - TCP Style TOP Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 3 15/16” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-342 ENGLISH METRIC Nominal Gun Outside Diameter: 4.50 in. 114.3 mm Nominal Gun Body Wall Thickness: .375 in. 9.53 mm Maximum Shot Density: 6 spf 19 spm Angular Phasing - Charge to Charge: 60º 60º Angular Phasing - Bank to Bank: 60º 60º Vertical Charge Spacing: 2.00 in. 50.8 mm Vertical Planes Perforated per Repeat Shot Pattern: 6 6 Horizontal Planes Perforated per Repeat Shot Pattern: 6 6 Minimum Recommended Cord Velocity Of Detonation: 22,000 ft/sec 6,700 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 19,500 psi 134.85 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 3.696 in. (10 in.) 93.88 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0445 or 0414)-C04-066 (18 shots) 48 in. 1.22 m Gun Assy (0445 or 0414)-C07-066 (36 shots) 84 in. 2.13 m Gun Assy (0445 or 0414)-C11-066 (60 shots) 132 in. 3.35 m Gun Assy (0445 or 0414)-C21-066 (120 shots) 252 in. 6.40 m Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.40 in.) 35.05 mm (60.96 mm) Gun End to First Scallop Distance: 7.20 in. 182.88 mm Calculated Break Point Tensile Strength - Hardware Only (8): 453,000 lbs. 2,015,000 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 6-5/8 in. 168.3 mm Minimum Recommended Casing Weight: (9): 20.0 lbs/ft 29.79 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ 34.0g RDX (11): 4.798 in. (4.776 in.) 121.87 mm (121.31 mm) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ 39.0g RDX (11): 4.743 in. (4.702 in.) 120.47 mm (119.43 mm) Minimum Recommended I.D. Running Restriction: 4.915 in. 124.84 mm Minimum Recommended Washover Pipe Clearance Requirements:





8 SPF - 135º PHASE

Charge Arrangement: MEDIUM SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0445 - Wireline Style BOTTOM Fired Gun Series 0414 - TCP Style TOP Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 3 15/16” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-342 ENGLISH METRIC Nominal Gun Outside Diameter: 4.50 in. 114.3 mm Nominal Gun Body Wall Thickness: .375 in. 9.53 mm Maximum Shot Density: 8 spf 26 spm Angular Phasing - Charge to Charge: 135º 135º Angular Phasing - Bank to Bank: 45º 45º Vertical Charge Spacing: 1.50 in. 38.1 mm Vertical Planes Perforated per Repeat Shot Pattern: 8 8 Horizontal Planes Perforated per Repeat Shot Pattern: 8 8 Minimum Recommended Cord Velocity Of Detonation: 23,000 ft/sec 7,000 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 19,500 psi 134.45 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 3.696 in. (10 in.) 93.88 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0445 or 0414)-1D04-08D (24 shots) 48 in. 1.22 m Gun Assy (0445 or 0414)-1D07-08D (48 shots) 84 in. 2.13 m Gun Assy (0445 or 0414)-1D11-08D (80 shots) 132 in. 3.35 m Gun Assy (0445 or 0414)-1D21-08D (160 shots) 252 in. 6.40 m Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.40 in.) 35.05 mm (60.96 mm) Gun End to First Scallop Distance: 6.75 in. 171.45 mm Calculated Break Point Tensile Strength - Hardware Only (8): 453,000 lbs. 2,015,000 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 6-5/8 in. 168.3 mm Minimum Recommended Casing Weight: (9): 20.0 lbs/ft 29.79 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Minimum Recommended I.D. Running Restriction: 4.915 in. 124.84 mm Minimum Recommended Washover Pipe Clearance Requirements:





CLUSTER STYLE, 12 SPF - 60º PHASE

Charge Arrangement: HIGH SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0445 - Wireline Style BOTTOM Fired Gun Series 0414 - TCP Style TOP Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 3 15/16” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-342 ENGLISH METRIC Nominal Gun Outside Diameter: 4.50 in. 114.3 mm Nominal Gun Body Wall Thickness: .375 in. 9.53 mm Maximum Shot Density: 12 spf 39 spm Angular Phasing - Charge to Charge: 120º 120º Angular Phasing - Bank to Bank: 60º 60º Vertical Charge Spacing: 3.00 in. 76.2 mm Vertical Planes Perforated per Repeat Shot Pattern: 6 6 Horizontal Planes Perforated per Repeat Shot Pattern: 2 2 Minimum Recommended Cord Velocity Of Detonation: 21,000 ft/sec 6,400 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 17,000 psi 117.22 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 3.696 in. (10 in.) 93.88 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0445 or 0414)-J04-126 (36 shots) 48 in. 1.22 m Gun Assy (0445 or 0414)-J07-126 (72 shots) 84 in. 2.13 m Gun Assy (0445 or 0414)-J11-126 (120 shots) 132 in. 3.35 m Gun Assy (0445 or 0414)-J21-126 (240 shots) 252 in. 6.40 m Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.40 in.) 35.05 mm (60.96 mm) Gun End to First Scallop Distance: 7.50 in. 190.50 mm Calculated Break Point Tensile Strength - Hardware Only (8): 453,000 lbs. 2,015,000 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 6-5/8 in. 168.3 mm Minimum Recommended Casing Weight: (9): 20.0 lbs/ft 29.79 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): 26.0g RDX/HMX 26.0g RDX/HMX Maximum (Average) Test Gun Swell @ 21.0g RDX (11): 4.534 in. (4.517 in.) 115.16 mm (114.73 mm) Minimum Recommended I.D. Running Restriction: 4.915 in. 124.84 mm Minimum Recommended Washover Pipe Clearance Requirements:


Vertical Drop Test (14): T.B.D. (12) T.B.D. (12) Horizontal Drop Test (14): T.B.D. (12) T.B.D. (12) Estimated Gun Assy Weight without Explosives: 16.8 lbs/ft 25.0 kg/m Estimated Gun Assy Weight with DP Charge (15): 19.2 lbs/ft 28.6 kg/m Estimated Gun Assy Weight with BH Charge (15): 18.9 lbs/ft 28.2 kg/m 112020071607




Charge Arrangement: HIGH SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0445 - Wireline Style BOTTOM Fired Gun Series 0414 - TCP Style TOP Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 3 15/16” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-342 ENGLISH METRIC Nominal Gun Outside Diameter: 4.50 in. 114.3 mm Nominal Gun Body Wall Thickness: .375 in. 9.53 mm Maximum Shot Density: 12 spf 39 spm Angular Phasing - Charge to Charge: 135º 135º Angular Phasing - Bank to Bank: 45º 45º Vertical Charge Spacing: 1.00 in. 25.4 mm Vertical Planes Perforated per Repeat Shot Pattern: 8 8 Horizontal Planes Perforated per Repeat Shot Pattern: 8 8 Minimum Recommended Cord Velocity Of Detonation: 23,000 ft/sec 7,000 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 19,500 psi 134.45 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 3.696 in. (10 in.) 93.88 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0445 or 0414)-1K04-12D (36 shots) 48 in. 1.22 m Gun Assy (0445 or 0414)-1K07-12D (72 shots) 84 in. 2.13 m Gun Assy (0445 or 0414)-1K11-12D (120 shots) 132 in. 3.35 m Gun Assy (0445 or 0414)-1K21-12D (240 shots) 252 in. 6.40 m Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.40 in.) 35.05 mm (60.96 mm) Gun End to First Scallop Distance: 6.50 in. 165.1 mm Calculated Break Point Tensile Strength - Hardware Only (8): 453,000 lbs. 2,015,000 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 6-5/8 in. 168.3 mm Minimum Recommended Casing Weight: (9): 20.0 lbs/ft 29.79 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): 18.0g RDX/HMX 18.0g RDX/HMX Maximum (Average) Test Gun Swell @ 18.0g RDX (11): 4.785 in. (4.749 in.) 121.54 mm (120.62 mm) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): 28.0g RDX/HMX 28.0g RDX/HMX Maximum (Average) Test Gun Swell @ 21.0g RDX (11): 4.687 in. (4.664 in.) 119.05 mm (118.47 mm) Minimum Recommended I.D. Running Restriction: 4.915 in. 124.84 mm Minimum Recommended Washover Pipe Clearance Requirements:






Charge Arrangement: ULTRA - HIGH SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0445 - Wireline Style BOTTOM Fired Gun Series 0414 - TCP Style TOP Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 3 15/16” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-342 ENGLISH METRIC Nominal Gun Outside Diameter: 4.50 in. 114.3 mm Nominal Gun Body Wall Thickness: .375 in. 9.53 mm Maximum Shot Density: 16 spf 52.5 spm Angular Phasing - Charge to Charge: 140º 140º Angular Phasing - Bank to Bank: 20º 20º Vertical Charge Spacing: .75 in. 19.05 mm Vertical Planes Perforated per Repeat Shot Pattern: 18 18 Horizontal Planes Perforated per Repeat Shot Pattern: 18 18 Minimum Recommended Cord Velocity Of Detonation: 24,750 ft/sec 7,500 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 18,500 psi 127.55 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 3.696 in. (10 in.) 93.88 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0445 or 0414)-C04-16G (48 shots) 48 in. 1.22 m Gun Assy (0445 or 0414)-C07-16G (96 shots) 84 in. 2.13 m Gun Assy (0445 or 0414)-C11-16G (160 shots) 132 in. 3.35 m Gun Assy (0445 or 0414)-C21-16G (320 shots) 252 in. 6.40 m Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to First Scallop Distance: 6.38 in. 162.05 mm Calculated Break Point Tensile Strength - Hardware Only (8): 453,000 lbs. 2,015,000 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 6-5/8 in. 168.3 mm Minimum Recommended Casing Weight: (9): 20.0 lbs/ft 29.79 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): NOT RECOMMENDED NOT RECOMMENDED Maximum (Average) Test Gun Swell @ RDX (11): NOT RECOMMENDED NOT RECOMMENDED Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Minimum Recommended I.D. Running Restriction: 4.915 in. 124.84 mm Minimum Recommended Washover Pipe Clearance Requirements:






Charge Arrangement: ULTRA - HIGH SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0445 - Wireline Style BOTTOM Fired Gun Series 0414 - TCP Style TOP Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 3 15/16” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-342 ENGLISH METRIC Nominal Gun Outside Diameter: 4.50 in. 114.3 mm Nominal Gun Body Wall Thickness: .375 in. 9.53 mm Maximum Shot Density: 18 spf 59 spm Angular Phasing - Charge to Charge: 140º 140º Angular Phasing - Bank to Bank: 20º 20º Vertical Charge Spacing: .667 in. 16.93 mm Vertical Planes Perforated per Repeat Shot Pattern: 18 18 Horizontal Planes Perforated per Repeat Shot Pattern: 18 18 Minimum Recommended Cord Velocity Of Detonation: 24,750 ft/sec 7,500 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 18,000 psi 124.11 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 3.696 in. (10 in.) 93.88 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0445 or 0414)-D04-18G (54 shots) 48 in. 1.22 m Gun Assy (0445 or 0414)-D07-18G (108 shots) 84 in. 2.13 m Gun Assy (0445 or 0414)-D11-18G (180 shots) 132 in. 3.35 m Gun Assy (0445 or 0414)-D21-18G (360 shots) 252 in. 6.40 m Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to First Scallop Distance: 6.38 in. 162.05 mm Calculated Break Point Tensile Strength - Hardware Only (8): 453,000 lbs. 2,015,000 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 6-5/8 in. 168.3 mm Minimum Recommended Casing Weight: (9): 20.0 lbs/ft 29.79 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): NOT RECOMMENDED NOT RECOMMENDED Maximum (Average) Test Gun Swell @ RDX (11): NOT RECOMMENDED NOT RECOMMENDED Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Minimum Recommended I.D. Running Restriction: 4.915 in. 124.84 mm Minimum Recommended Washover Pipe Clearance Requirements:





4 SPF - 90º PHASE

Charge Arrangement: LOW SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0446 - Wireline Style BOTTOM Fired Gun Series 0416 - TCP Style TOP Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 3 15/16” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-342 ENGLISH METRIC Nominal Gun Outside Diameter: 4.63 in. 117.5 mm Nominal Gun Body Wall Thickness: .438 in. 11.1 mm Maximum Shot Density: 4 spf 13 spm Angular Phasing - Charge to Charge: 90º 90º Angular Phasing - Bank to Bank: 90º 90º Vertical Charge Spacing: 3.00 in. 76.20 mm Vertical Planes Perforated per Repeat Shot Pattern: 4 4 Horizontal Planes Perforated per Repeat Shot Pattern: 4 4 Minimum Recommended Cord Velocity Of Detonation: 21,000 ft/sec 6,400 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 21,000 psi 144.79 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 3.696 in. (10 in.) 93.88 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0446 or 0416)-A04-044 (12 shots) 48 in. 1.22 m Gun Assy (0446 or 0416)-A07-044 (24 shots) 84 in. 2.13 m Gun Assy (0446 or 0416)-A11-044 (40 shots) 132 in. 3.35 m Gun Assy (0446 or 0416)-A21-044 (80 shots) 252 in. 6.40 m Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to First Scallop Distance: 7.50 in. 190.50 mm Calculated Break Point Tensile Strength - Hardware Only (8): 600,000 lbs. 2,668,800 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 6-5/8 in. 168.3 mm Minimum Recommended Casing Weight: (9): 20.0 lbs/ft 29.79 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Minimum Recommended I.D. Running Restriction: 5.000 in. 127.00 mm Minimum Recommended Washover Pipe Clearance Requirements:





5 SPF - 60º PHASE

Charge Arrangement: MEDIUM SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0446 - Wireline Style BOTTOM Fired Gun Series 0416 - TCP Style TOP Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 3 15/16” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-342 ENGLISH METRIC Nominal Gun Outside Diameter: 4.63 in. 117.5 mm Nominal Gun Body Wall Thickness: .438 in. 11.1 mm Maximum Shot Density: 5 spf 16 spm Angular Phasing - Charge to Charge: 60º 60º Angular Phasing - Bank to Bank: 60º 60º Vertical Charge Spacing: 2.40 in. 61.0 mm Vertical Planes Perforated per Repeat Shot Pattern: 6 6 Horizontal Planes Perforated per Repeat Shot Pattern: 6 6 Minimum Recommended Cord Velocity Of Detonation: 25,000 ft/sec 7,600 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 21,000 psi 144.79 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 3.696 in. (10 in.) 93.88 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0446 or 0416)-1A04-056 (15 shots) 48 in. 1.22 m Gun Assy (0446 or 0416)-1A07-056 (30 shots) 84 in. 2.13 m Gun Assy (0446 or 0416)-1A11-056 (50 shots) 132 in. 3.35 m Gun Assy (0446 or 0416)-1A21-056 (100 shots) 252 in. 6.40 m Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to First Scallop Distance: 7.20 in. 182.88 mm Calculated Break Point Tensile Strength - Hardware Only (8): 600,000 lbs. 2,668,800 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 6-5/8 in. 168.3 mm Minimum Recommended Casing Weight: (9): 20.0 lbs/ft 29.79 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): 39.0g RDX/HMX (12)

39.0g RDX/HMX Maximum (Average) Test Gun Swell @ 39g RDX (11): 4.874 in. (4.850 in.) 123.80 mm (123.19 mm) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): 39.0g RDX/HMX (12)

39.0g RDX/HMX Maximum (Average) Test Gun Swell @ 39g RDX (11): 4.835 in. (4.800 in.) 122.81 mm (121.92 mm) Minimum Recommended I.D. Running Restriction: 5.000 in. 127.0 mm Minimum Recommended Washover Pipe Clearance Requirements:





6 SPF - 60º PHASE

Charge Arrangement: MEDIUM SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0446 - Wireline Style BOTTOM Fired Gun Series 0416 - TCP Style TOP Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 3 15/16” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-342 ENGLISH METRIC Nominal Gun Outside Diameter: 4.63 in. 117.5 mm Nominal Gun Body Wall Thickness: .438 in. 11.1 mm Maximum Shot Density: 6 spf 19 spm Angular Phasing - Charge to Charge: 60º 60º Angular Phasing - Bank to Bank: 60º 60º Vertical Charge Spacing: 2.00 in. 50.8 mm Vertical Planes Perforated per Repeat Shot Pattern: 6 6 Horizontal Planes Perforated per Repeat Shot Pattern: 6 6 Minimum Recommended Cord Velocity Of Detonation: 22,000 ft/sec 6,700 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 21,000 psi 144.79 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 3.696 in. (10 in.) 93.88 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0446 or 0416)-C04-066 (18 shots) 48 in. 1.22 m Gun Assy (0446 or 0416)-C07-066 (36 shots) 84 in. 2.13 m Gun Assy (0446 or 0416)-C11-066 (60 shots) 132 in. 3.35 m Gun Assy (0446 or 0416)-C21-066 (120 shots) 252 in. 6.40 m Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (60.85 mm) Gun End to First Scallop Distance: 7.00 in. 177.8 mm Calculated Break Point Tensile Strength - Hardware Only (8): 600,000 lbs. 2,668,800 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 6-5/8 in. 168.3 mm Minimum Recommended Casing Weight: (9): 20.0 lbs/ft 29.79 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Minimum Recommended I.D. Running Restriction: 5.000 in. 127.0 mm Minimum Recommended Washover Pipe Clearance Requirements:





8 SPF - 135º PHASE

Charge Arrangement: MEDIUM SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0446 - Wireline Style BOTTOM Fired Gun Series 0416 - TCP Style TOP Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 3 15/16” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-342 ENGLISH METRIC Nominal Gun Outside Diameter: 4.63 in. 117.5 mm Nominal Gun Body Wall Thickness: .438 in. 11.1 mm Maximum Shot Density: 8 spf 26 spm Angular Phasing - Charge to Charge: 135º 135º Angular Phasing - Bank to Bank: 45º 45º Vertical Charge Spacing: 1.50 in. 38.1 mm Vertical Planes Perforated per Repeat Shot Pattern: 8 8 Horizontal Planes Perforated per Repeat Shot Pattern: 8 8 Minimum Recommended Cord Velocity Of Detonation: 23,000 ft/sec 7,000 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 21,000 psi 144.79 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 3.696 in. (10 in.) 93.88 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0446 or 0416)-1D04-08D (24 shots) 48 in. 1.22 m Gun Assy (0446 or 0416)-1D07-08D (48 shots) 84 in. 2.13 m Gun Assy (0446 or 0416)-1D11-08D (80 shots) 132 in. 3.35 m Gun Assy (0446 or 0416)-1D21-08D (160 shots) 252 in. 6.40 m Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to First Scallop Distance: 6.75 in. 171.45 mm Calculated Break Point Tensile Strength - Hardware Only (8): 600,000 lbs. 2,668,800 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 6-5/8 in. 168.3 mm Minimum Recommended Casing Weight: (9): 20.0 lbs/ft 29.79 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Minimum Recommended I.D. Running Restriction: 5.000 in. 127.0 mm Minimum Recommended Washover Pipe Clearance Requirements:






Charge Arrangement: HIGH SHOT DENSITY, ROTATED CLUSTER Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0446 - Wireline Style BOTTOM Fired Gun Series 0416 - TCP Style TOP Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 3 15/16” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-342 ENGLISH METRIC Nominal Gun Outside Diameter: 4.63 in. 117.5 mm Nominal Gun Body Wall Thickness: .438 in. 11.1 mm Maximum Shot Density: 12 spf 39 spm Angular Phasing - Charge to Charge: 120º 120º Angular Phasing - Bank to Bank: 60º 60º Vertical Charge Spacing: 3.00 in. 76.2 mm Vertical Planes Perforated per Repeat Shot Pattern: 6 6 Horizontal Planes Perforated per Repeat Shot Pattern: 2 2 Minimum Recommended Cord Velocity Of Detonation: 21,000 ft/sec 6,400 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 19,500 psi 134.45 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 3.696 in. (10 in.) 93.88 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0446 or 0416)-J04-126 (36 shots) 48 in. 1.22 m Gun Assy (0446 or 0416)-J07-126 (72 shots) 84 in. 2.13 m Gun Assy (0446 or 0416)-J11-126 (120 shots) 132 in. 3.35 m Gun Assy (0446 or 0416)-J21-126 (240 shots) 252 in. 6.40 m Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to First Scallop Distance: 7.50 in. 190.50 mm Calculated Break Point Tensile Strength - Hardware Only (8): 600,000 lbs. 2,668,800 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 6-5/8 in. 168.3 mm Minimum Recommended Casing Weight: (9): 20.0 lbs/ft 29.79 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): 26.0g RDX/HMX 26.0g RDX/HMX Maximum (Average) Test Gun Swell @ 21.0g RDX (11): 4.698 in. (4.676 in.) 119.33 mm (118.77 mm) Minimum Recommended I.D. Running Restriction: 5.000 in. 127.0 mm Minimum Recommended Washover Pipe Clearance Requirements:






Charge Arrangement: HIGH SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0446 - Wireline Style BOTTOM Fired Gun Series 0416 - TCP Style TOP Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 3 15/16” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-342 ENGLISH METRIC Nominal Gun Outside Diameter: 4.63 in. 117.5 mm Nominal Gun Body Wall Thickness: .438 in. 11.1 mm Maximum Shot Density: 12 spf 39 spm Angular Phasing - Charge to Charge: 135º 135º Angular Phasing - Bank to Bank: 45º 45º Vertical Charge Spacing: 1.00 in. 25.4 mm Vertical Planes Perforated per Repeat Shot Pattern: 8 8 Horizontal Planes Perforated per Repeat Shot Pattern: 8 8 Minimum Recommended Cord Velocity Of Detonation: 23,000 ft/sec 7,000 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 20,500 psi 141.34 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 3.696 in. (10 in.) 93.88 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0446 or 0416)-1K04-12D (36 shots) 48 in. 1.22 m Gun Assy (0446 or 0416)-1K07-12D (72 shots) 84 in. 2.13 m Gun Assy (0446 or 0416)-1K11-12D (120 shots) 132 in. 3.35 m Gun Assy (0446 or 0416)-1K21-12D (240 shots) 252 in. 6.40 m Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to First Scallop Distance: 6.50 in. 165.1 mm Calculated Break Point Tensile Strength - Hardware Only (8): 600,000 lbs. 2,668,800 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 6-5/8 in. 168.3 mm Minimum Recommended Casing Weight: (9): 20.0 lbs/ft 29.79 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Minimum Recommended I.D. Running Restriction: 5.000 in. 127.0 mm Minimum Recommended Washover Pipe Clearance Requirements:






Charge Arrangement: ULTRA - HIGH SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0446 - Wireline Style BOTTOM Fired Gun Series 0416 - TCP Style TOP Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 3 15/16” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-342 ENGLISH METRIC Nominal Gun Outside Diameter: 4.63 in. 117.5 mm Nominal Gun Body Wall Thickness: .438 in. 11.1 mm Maximum Shot Density: 16 spf 52.5 spm Angular Phasing - Charge to Charge: 140º 140º Angular Phasing - Bank to Bank: 20º 20º Vertical Charge Spacing: .75 in. 19.05 mm Vertical Planes Perforated per Repeat Shot Pattern: 18 18 Horizontal Planes Perforated per Repeat Shot Pattern: 18 18 Minimum Recommended Cord Velocity Of Detonation: 24,750 ft/sec 7,500 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 21,500 psi 148.24 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 3.696 in. (10 in.) 93.88 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0446 or 0416)-C04-16G (48 shots) 48 in. 1.22 m Gun Assy (0446 or 0416)-C07-16G (96 shots) 84 in. 2.13 m Gun Assy (0446 or 0416)-C11-16G (160 shots) 132 in. 3.35 m Gun Assy (0446 or 0416)-C21-16G (320 shots) 252 in. 6.40 m Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to First Scallop Distance: 6.38 in. 162.05 mm Calculated Break Point Tensile Strength - Hardware Only (8): 600,000 lbs. 2,668,800 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 6-5/8 in. 168.3 mm Minimum Recommended Casing Weight: (9): 20.0 lbs/ft 29.79 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Minimum Recommended I.D. Running Restriction: 5.000 in. 127.0 mm Minimum Recommended Washover Pipe Clearance Requirements:





SPIRAL CLUSTER, 18 SPF - 55º PHASE

Charge Arrangement: ULTRA-HIGH DENSITY, ROTATED CLUSTER Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0446 - Wireline Style BOTTOM Fired Gun Series 0416 - TCP Style TOP Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 3 15/16” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-342 ENGLISH METRIC Nominal Gun Outside Diameter: 4.63 in. 117.5 mm Nominal Gun Body Wall Thickness: .438 in. 11.1 mm Maximum Shot Density: 18 spf 59 spm Angular Phasing - Charge to Charge: 120º 120º Angular Phasing - Bank to Bank: 55º 55º Vertical Charge Spacing: 2.00 in. 50.8 mm Vertical Planes Perforated per Repeat Shot Pattern: 72 72 Horizontal Planes Perforated per Repeat Shot Pattern: 24 24 Minimum Recommended Cord Velocity Of Detonation: 22,000 ft/sec 6,700 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 18,000 psi 124.11 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 3.696 in.(10 in.) 93.88 mm(254 mm) Standard Overall Gun Lengths (7): Gun Assy (0446 or 0416)-K04-1855 (54 shots) 48 in. 1.22 m Gun Assy (0446 or 0416)-K07-1855 (108 shots) 84 in. 2.13 m Gun Assy (0446 or 0416)-K11-1855 (180 shots) 132 in. 3.35 m Gun Assy (0446 or 0416)-K21-1855 (360 shots) 252 in. 6.40 m Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to Center of First Scallop Distance: 7.00 in. 177.8 mm Calculated Break Point Tensile Strength - Hardware Only (8): 600,000 lbs. 2,668,800 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 6-5/8 in. 168.3 mm Minimum Recommended Casing Weight (9): 20.0 lbs/ft 29.79 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX: T.B.D. (12) T.B.D. (12) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): 21.0g RDX/HMX 21.0g RDX/HMX Maximum (Average) Test Gun Swell @ 21.0g RDX (11): 4.708 in. (4.692 in.) 119.58 mm (119.18 mm) Minimum Recommended I.D. Running Restriction: 5.000 in. 127.00 mm Minimum Recommended Washover Pipe Clearance Requirements:


Vertical Drop Test (14): T.B.D. (12) T.B.D. (12) Horizontal Drop Test (14): T.B.D. (12) T.B.D. (12) Estimated Gun Assy Weight without Explosives: 20.0 lbs/ft 29.7 kg/m Estimated Gun Assy Weight with DP Charge (12,15): T.B.D. T.B.D. Estimated Gun Assy Weight with BH Charge (12,15): T.B.D. (12) T.B.D. (12) 112120071546




Charge Arrangement: ULTRA - HIGH SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0446 - Wireline Style BOTTOM Fired Gun Series 0416 - TCP Style TOP Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 3 15/16” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-342 ENGLISH METRIC Nominal Gun Outside Diameter: 4.63 in. 117.5 mm Nominal Gun Body Wall Thickness: .438 in. 11.1 mm Maximum Shot Density: 18 spf 59 spm Angular Phasing - Charge to Charge: 140º 140º Angular Phasing - Bank to Bank: 20º 20º Vertical Charge Spacing: .667 in. 16.93 mm Vertical Planes Perforated per Repeat Shot Pattern: 18 18 Horizontal Planes Perforated per Repeat Shot Pattern: 18 18 Minimum Recommended Cord Velocity Of Detonation: 24,750 ft/sec 7,500 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 21,000 psi 144.79 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 3.696 in. (10 in.) 93.88 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0446 or 0416)-D04-18G (54 shots) 48 in. 1.22 m Gun Assy (0446 or 0416)-D07-18G (108 shots) 84 in. 2.13 m Gun Assy (0446 or 0416)-D11-18G (180 shots) 132 in. 3.35 m Gun Assy (0446 or 0416)-D21-18G (360 shots) 252 in. 6.40 m Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to First Scallop Distance: 6.38 in. 162.05 mm Calculated Break Point Tensile Strength - Hardware Only (8): 600,000 lbs. 2,668,800 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 6-5/8 in. 168.3 mm Minimum Recommended Casing Weight: (9): 20.0 lbs/ft 29.79 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Minimum Recommended I.D. Running Restriction: 5.000 in. 127.0 mm Minimum Recommended Washover Pipe Clearance Requirements:





4 SPF - 90º PHASE

Charge Arrangement: LOW SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0336 - Wireline Style BOTTOM Fired Gun Series 0405 - TCP Style TOP Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 4 1/4” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-344 ENGLISH METRIC Nominal Gun Outside Diameter: 5.00 in. 127.0 mm Nominal Gun Body Wall Thickness: .500 in. 12.7 mm Maximum Shot Density: 4 spf 13 spm Angular Phasing - Charge to Charge: 90º 90º Angular Phasing - Bank to Bank: 90º 90º Vertical Charge Spacing: 3.00 in. 76.2 mm Vertical Planes Perforated per Repeat Shot Pattern: 4 4 Horizontal Planes Perforated per Repeat Shot Pattern: 4 4 Minimum Recommended Cord Velocity Of Detonation: 21,000 ft/sec 6,400 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 20,000 psi 137.90 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 3.920 in. (10 in.) 99.57 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0336 or 0405)-A04-044 (12 shots) 48 in. 1.22 m Gun Assy (0336 or 0405)-A07-044 (24 shots) 84 in. 2.13 m Gun Assy (0336 or 0405)-A11-044 (40 shots) 132 in. 3.35 m Gun Assy (0336 or 0405)-A21-044 (80 shots) 252 in. 6.40 m Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to First Scallop Distance: 7.50 in. 190.50 mm Calculated Break Point Tensile Strength - Hardware Only (8): 678,000 lbs. 3,016,000 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 7.00 in. 177.8 mm Minimum Recommended Casing Weight: (9): 20.0 lbs/ft 29.79 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): T.B.D. (12) T.B.D. (12)

Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Minimum Recommended I.D. Running Restriction: 5.62 in. 142.88 mm Minimum Recommended Washover Pipe Clearance Requirements:


Vertical Drop Test (14): T.B.D. (12) T.B.D. (12) Horizontal Drop Test (14): T.B.D. (12) T.B.D. (12) Estimated Gun Assy Weight without Explosives: T.B.D. (12) T.B.D. (12) Estimated Gun Assy Weight with DP Charges (15): T.B.D. (12) T.B.D. (12) 112620070957



5 SPF - 60º PHASE

Charge Arrangement: MEDIUM SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0336 - Wireline Style BOTTOM Fired Gun Series 0405 - TCP Style TOP Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 4 1/4” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-344 ENGLISH METRIC Nominal Gun Outside Diameter: 5.00 in. 127.0 mm Nominal Gun Body Wall Thickness: .500 in. 12.7 mm Maximum Shot Density: 5 spf 16 spm Angular Phasing - Charge to Charge: 60º 60º Angular Phasing - Bank to Bank: 60º 60º Vertical Charge Spacing: 2.00 in. 50.8 mm Vertical Planes Perforated per Repeat Shot Pattern: 6 6 Horizontal Planes Perforated per Repeat Shot Pattern: 6 6 Minimum Recommended Cord Velocity Of Detonation: 22,000 ft/sec 6,700 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 20,000 psi 137.90 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 3.920 in. (10 in.) 99.57 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0336 or 0405)-1A04-066 (18 shots) 48 in. 1.22 m Gun Assy (0336 or 0405)-1A07-066 (36 shots) 84 in. 2.13 m Gun Assy (0336 or 0405)-1A11-066 (60 shots) 132 in. 3.35 m Gun Assy (0336 or 0405)-1A21-066 (120 shots) 252 in. 6.40 m Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to First Scallop Distance: 7.20 in. 182.88 mm Calculated Break Point Tensile Strength - Hardware Only (8): 678,000 lbs. 3,016,000 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 7.00 in. 177.88 mm Minimum Recommended Casing Weight: (9): 20.0 lbs/ft 29.79 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. T.B.D. Minimum Recommended I.D. Running Restriction: 5.625 in. 142.88 mm Minimum Recommended Washover Pipe Clearance Requirements:





6 SPF - 60º PHASE

Charge Arrangement: MEDIUM SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0336 - Wireline Style BOTTOM Fired Gun Series 0405 - TCP Style TOP Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 4 1/4” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-344 ENGLISH METRIC Nominal Gun Outside Diameter: 5.00 in. 127.0 mm Nominal Gun Body Wall Thickness: .500 in. 12.7 mm Maximum Shot Density: 6 spf 19 spm Angular Phasing - Charge to Charge: 60º 60º Angular Phasing - Bank to Bank: 60º 60º Vertical Charge Spacing: 2.00 in. 50.8 mm Vertical Planes Perforated per Repeat Shot Pattern: 6 6 Horizontal Planes Perforated per Repeat Shot Pattern: 6 6 Minimum Recommended Cord Velocity Of Detonation: 22,000 ft/sec 6,700 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 20,000 psi 137.90 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 3.920 in. (10 in.) 99.57 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0336 or 0405)-C04-066 (18 shots) 48 in. 1.22 m Gun Assy (0336 or 0405)-C07-066 (36 shots) 84 in. 2.13 m Gun Assy (0336 or 0405)-C11-066 (60 shots) 132 in. 3.35 m Gun Assy (0336 or 0405)-C21-066 (120 shots) 252 in. 6.40 m Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to First Scallop Distance: 7.00 in. 177.80 mm Calculated Break Point Tensile Strength - Hardware Only (8): 678,000 lbs. 3,016,000 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 7.00 in. 177.8 mm Minimum Recommended Casing Weight: (9): 20.0 lbs/ft 29.79 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. T.B.D. Minimum Recommended I.D. Running Restriction: 5.625 in. 142.88 mm Minimum Recommended Washover Pipe Clearance Requirements:





8 SPF - 135º PHASE

Charge Arrangement: MEDIUM SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0336 - Wireline Style BOTTOM Fired Gun Series 0405 - TCP Style TOP Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 4 1/4” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-344 ENGLISH METRIC Nominal Gun Outside Diameter: 5.00 in. 127.0 mm Nominal Gun Body Wall Thickness: .500 in. 12.7 mm Maximum Shot Density: 8 spf 26 spm Angular Phasing - Charge to Charge: 135º 135º Angular Phasing - Bank to Bank: 45º 45º Vertical Charge Spacing: 1.50 in. 38.1 mm Vertical Planes Perforated per Repeat Shot Pattern: 8 8 Horizontal Planes Perforated per Repeat Shot Pattern: 12 12 Minimum Recommended Cord Velocity Of Detonation: 23,000 ft/sec 7,000 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 20,000 psi 137.90 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 3.920 in. (10 in.) 99.57 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0336 or 0405)-2K04-08D (36 shots) 48 in. 1.22 m Gun Assy (0336 or 0405)-2K07-08D (72 shots) 84 in. 2.13 m Gun Assy (0336 or 0405)-2K11-08D (120 shots) 132 in. 3.35 m Gun Assy (0336 or 0405)-2K21-08D (240 shots) 252 in. 6.40 m Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to First Scallop Distance: 6.75 in. 171.45 mm Calculated Break Point Tensile Strength - Hardware Only (8): 678,000 lbs. 3,016,000 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 7.00 in. 177.8 mm Minimum Recommended Casing Weight: (9): 20.0 lbs/ft 29.79 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Minimum Recommended I.D. Running Restriction: 5.625 in. 147.88 mm Minimum Recommended Washover Pipe Clearance Requirements:






Charge Arrangement: HIGH SHOT DENSITY, ROTATED CLUSTER Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0336 - Wireline Style BOTTOM Fired Gun Series 0405 - TCP Style TOP Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 4 1/4” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-344 ENGLISH METRIC Nominal Gun Outside Diameter: 5.00 in. 127.0 mm Nominal Gun Body Wall Thickness: .500 in. 12.7 mm Maximum Shot Density: 12 spf 39 spm Angular Phasing - Charge to Charge: 120º 120º Angular Phasing - Bank to Bank: 60º 60º Vertical Charge Spacing: 3.00 in. 76.2 mm Vertical Planes Perforated per Repeat Shot Pattern: 6 6 Horizontal Planes Perforated per Repeat Shot Pattern: 2 2 Minimum Recommended Cord Velocity Of Detonation: 21,000 ft/sec 6,400 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 20,000 psi 137.90 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 3.920 in. (10 in.) 99.57 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0336 or 0405)-K04-126 (36 shots) 48 in. 1.22 m Gun Assy (0336 or 0405)-K07-126 (72 shots) 84 in. 2.13 m Gun Assy (0336 or 0405)-K11-126 (120 shots) 132 in. 3.35 m Gun Assy (0336 or 0405)-K21-126 (240 shots) 252 in. 6.40 m Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to First Scallop Distance: 7.50 in. 190.50 mm Calculated Break Point Tensile Strength - Hardware Only (8): 678,000 lbs. 3,016,000 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 7.00 in. 177.8 mm Minimum Recommended Casing Weight: (9): 20.0 lbs/ft 29.79 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ 25.0g RDX (11): 5.078 in. (5.064 in.) 128.98 mm (128.63 mm) Minimum Recommended I.D. Running Restriction: 5.415 in. 137.54 mm Minimum Recommended Washover Pipe Clearance Requirements:


Vertical Drop Test (14): T.B.D. (12) T.B.D. (12) Horizontal Drop Test (14): T.B.D. (12) T.B.D. (12) Estimated Gun Assy Weight without Explosives: T.B.D. (12) T.B.D. (12) Estimated Gun Assy Weight with DP Charges (15): T.B.D. (12) T.B.D. (12) Estimated Gun Assy Weight with BH Charges (15): T.B.D. (12) T.B.D. (12) 112120071739




Charge Arrangement: HIGH SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0336 - Wireline Style BOTTOM Fired Gun Series 0405 - TCP Style TOP Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 4 1/4” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-344 ENGLISH METRIC Nominal Gun Outside Diameter: 5.00 in. 127.0 mm Nominal Gun Body Wall Thickness: .500 in. 12.7 mm Maximum Shot Density: 12 spf 39 spm Angular Phasing - Charge to Charge: 135º 135º Angular Phasing - Bank to Bank: 45º 45º Vertical Charge Spacing: 1.00 in. 25.4 mm Vertical Planes Perforated per Repeat Shot Pattern: 8 8 Horizontal Planes Perforated per Repeat Shot Pattern: 8 8 Minimum Recommended Cord Velocity Of Detonation: 23,000 ft/sec 7,000 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 20,000 psi 137.90 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 3.920 in. (10 in.) 99.57 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0336 or 0405)-1K04-12D (36 shots) 48 in. 1.22 m Gun Assy (0336 or 0405)-1K07-12D (72 shots) 84 in. 2.13 m Gun Assy (0336 or 0405)-1K11-12D (120 shots) 132 in. 3.35 m Gun Assy (0336 or 0405)-1K21-12D (240 shots) 252 in. 6.40 m Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to First Scallop Distance: 6.50 in. 165.10 mm Calculated Break Point Tensile Strength - Hardware Only (8): 678,000 lbs. 3,016,000 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 7.00 in. 177.8 mm Minimum Recommended Casing Weight: (9): 20.0 lbs/ft 29.79 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Minimum Recommended I.D. Running Restriction: 5.415 in. 137.54 mm Minimum Recommended Washover Pipe Clearance Requirements:






Charge Arrangement: ULTRA HIGH SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0336 - Wireline Style BOTTOM Fired Gun Series 0405 - TCP Style TOP Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 4 1/4” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-344 ENGLISH METRIC Nominal Gun Outside Diameter: 5.00 in. 127.0 mm Nominal Gun Body Wall Thickness: .500 in. 12.7 mm Maximum Shot Density: 16 spf 52.5 spm Angular Phasing - Charge to Charge: 140º 140º Angular Phasing - Bank to Bank: 20º 20º Vertical Charge Spacing: .75 in. 19.05 mm Vertical Planes Perforated per Repeat Shot Pattern: 18 18 Horizontal Planes Perforated per Repeat Shot Pattern: 18 18 Minimum Recommended Cord Velocity Of Detonation: 23,000 ft/sec 7,000 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 20,000 psi 137.90 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 3.920 in. (10 in.) 99.57 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0336 or 0405)-C04-16G (48 shots) 48 in. 1.22 m Gun Assy (0336 or 0405)-C07-16G (96 shots) 84 in. 2.13 m Gun Assy (0336 or 0405)-C11-16G (160 shots) 132 in. 3.35 m Gun Assy (0336 or 0405)-C21-16G (320 shots) 252 in. 6.40 m Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to First Scallop Distance: 6.38 in. 162.05 mm Calculated Break Point Tensile Strength - Hardware Only (8): 678,000 lbs. 3,016,000 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 7.00 in. 177.8 mm Minimum Recommended Casing Weight: (9): 20.0 lbs/ft 29.79 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Minimum Recommended I.D. Running Restriction: 5.625 in. 142.88 mm Minimum Recommended Washover Pipe Clearance Requirements:






Charge Arrangement: ULTRA-HIGH DENSITY, ROTATED CLUSTER Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0336 - Wireline Style BOTTOM Fired Gun Series 0405 - TCP Style TOP Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 4 1/4” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-344 ENGLISH METRIC Nominal Gun Outside Diameter: 5.00 in. 127.0 mm Nominal Gun Body Wall Thickness: .500 in. 12.7 mm Maximum Shot Density: 18 spf 59 spm Angular Phasing - Charge to Charge: 55º 55º Angular Phasing - Bank to Bank: 55º 55º Vertical Charge Spacing: 2.00 in. 50.8 mm Vertical Planes Perforated per Repeat Shot Pattern: 72 72 Horizontal Planes Perforated per Repeat Shot Pattern: 24 24 Minimum Recommended Cord Velocity Of Detonation: 22,000 ft/sec 6,700 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 17,000 psi 117.22 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 3.920 in. (10 in.) 99.57 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0336 or 0405)-K04-1855 (54 shots) 48 in. 1.22 m Gun Assy (0336 or 0405)-K07-1855 (108 shots) 84 in. 2.13 m Gun Assy (0336 or 0405)-K11-1855 (180 shots) 132 in. 3.35 m Gun Assy (0336 or 0405)-K21-1855 (360 shots) 252 in. 6.40 m Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to First Scallop Distance: 7.00 in. 177.8 mm Calculated Break Point Tensile Strength - Hardware Only (8): 678,000 lbs. 3,016,000 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 7.00 in. 177.8 mm Minimum Recommended Casing Weight: (9): 20.0 lbs/ft 29.79 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): NOT RECOMMENDED NOT RECOMMENDED Maximum (Average) Test Gun Swell @ RDX (11): NOT RECOMMENDED NOT RECOMMENDED Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): 26.0g RDX/HMX 26.0g RDX/HMX Maximum (Average) Test Gun Swell @ 26.0 g RDX (11): 5.187 in. (5.143 in.) 131.7 mm (130.6 mm) Minimum Recommended I.D. Running Restriction: 5.625 in. 142.88 mm Minimum Recommended Washover Pipe Clearance Requirements:


Vertical Drop Test (14): T.B.D. (12) T.B.D. (12) Horizontal Drop Test (14): T.B.D. (12) T.B.D. (12) Estimated Gun Assy Weight without Explosives: 24.7 lbs/ft 36.9 kg/m Estimated Gun Assy Weight with DP Charges (15): 33.6 lbs/ft 50.1 kg/m Estimated Gun Assy Weight with BH Charges (15): 33.5 lbs/ft 49.9 kg/m 122120071748




Charge Arrangement: ULTRA HIGH SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0336 - Wireline Style BOTTOM Fired Gun Series 0405 - TCP Style TOP Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 4 1/4” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-344 ENGLISH METRIC Nominal Gun Outside Diameter: 5.00 in. 127.0 mm Nominal Gun Body Wall Thickness: .500 in. 12.7 mm Maximum Shot Density: 18 spf 59 spm Angular Phasing - Charge to Charge: 140º 140º Angular Phasing - Bank to Bank: 20º 20º Vertical Charge Spacing: .667 in. 16.93 mm Vertical Planes Perforated per Repeat Shot Pattern: 18 18 Horizontal Planes Perforated per Repeat Shot Pattern: 18 18 Minimum Recommended Cord Velocity Of Detonation: 23,000 ft/sec 7,000 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 20,000 psi 137.90 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 3.920 in. (10 in.) 99.57 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0336 or 0405)-D04-18G (54 shots) 48 in. 1.22 m Gun Assy (0336 or 0405)-D07-18G (108 shots) 84 in. 2.13 m Gun Assy (0336 or 0405)-D11-18G (180 shots) 132 in. 3.35 m Gun Assy (0336 or 0405)-D21-18G (360 shots) 252 in. 6.40 m Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to First Scallop Distance: 6.38 in. 162.05 mm Calculated Break Point Tensile Strength - Hardware Only (8): 678,000 lbs. 3,016,000 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 7.00 in. 177.8 mm Minimum Recommended Casing Weight: (9): 20.0 lbs/ft 29.79 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Minimum Recommended I.D. Running Restriction: 5.625 in. 142.88 mm Minimum Recommended Washover Pipe Clearance Requirements:






Charge Arrangement: HIGH SHOT DENSITY, ROTATED CLUSTER Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0337 - Wireline Style BOTTOM Fired Gun Series 0406 - TCP Style TOP Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 5 1/4” - 6 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-352 ENGLISH METRIC Nominal Gun Outside Diameter: 6.00 in. 152.4 mm Nominal Gun Body Wall Thickness: .500 in. 12.7 mm Maximum Shot Density: 12 spf 39 spm Angular Phasing - Charge to Charge: 120º 120º Angular Phasing - Bank to Bank: 60º 60º Vertical Charge Spacing: 3.00 in. 76.2 mm Vertical Planes Perforated per Repeat Shot Pattern: 6 6 Horizontal Planes Perforated per Repeat Shot Pattern: 2 2 Minimum Recommended Cord Velocity Of Detonation: 21,000 ft/sec 6,400 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 16,500 psi 113.77 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 4.911 in. (10 in.) 124.74 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0337 or 0406)-K04-126 (36 shots) 48 in. 1.22 m Gun Assy (0337 or 0406)-K07-126 (72 shots) 84 in. 2.13 m Gun Assy (0337 or 0406)-K11-126 (120 shots) 132 in. 3.35 m Gun Assy (0337 or 0406)-K21-126 (240 shots) 252 in. 6.40 m Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (2.75 in.) 35.05 mm (69.85 mm) Gun End to Center of First Scallop Distance: 6.00 in. 152.40 mm Calculated Break Point Tensile Strength - Hardware Only (8): 815,000 lbs. 3,625,000 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 7-5/8 in. 193.7 mm Minimum Recommended Casing Weight: 24.0 lbs/ft 35.75 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ 28.0g RDX (11): 6.050 in. (6.032 in.) 153.67 mm (153.21 mm) Minimum Recommended I.D. Running Restriction: 6.376 in. 161.95 mm Minimum Recommended Washover Pipe Clearance Requirements:






Charge Arrangement: HIGH SHOT DENSITY, SEQUENTIAL Gun Body Material (1): Heat Treated, CD or HF, Seamless Steel Tubing Gun Body Configuration: Threaded & Scalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline, TCP, Coiled Tubing Mode Of Fire: Simultaneous Type of Tandem Connection (2): Lap Splice or Booster-to-Booster (Spliceless) Gun Positioning Requirements: Optional Initiation Point: Gun Series 0338 - Wireline Style BOTTOM Fired Gun Series 0407 - TCP Style TOP Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 6 1/4” - 5 ACME O-ring Material (3): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-360 ENGLISH METRIC Nominal Gun Outside Diameter: 7.00 in. 177.8 mm Nominal Gun Body Wall Thickness: .500 in. 12.7 mm Maximum Shot Density: 12 spf 39 spm Angular Phasing - Charge to Charge: 135º 135º Angular Phasing - Bank to Bank: 45º 45º Vertical Charge Spacing: 1.00 in. 25.4 mm Vertical Planes Perforated per Repeat Shot Pattern: 8 8 Horizontal Planes Perforated per Repeat Shot Pattern: 8 8 Minimum Recommended Cord Velocity Of Detonation: 23,000 ft/sec 7,000 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (4,5,6): 500º F 260º C Pressure Rating (4): 13,000 psi 89.64 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 5.903 in. (10 in.) 149.94 mm (254 mm) Standard Overall Gun Lengths (7): Gun Assy (0338 or 0407)-1D04-12D (36 shots) 48 in. 1.22 m Gun Assy (0338 or 0407)-1D07-12D (72 shots) 84 in. 2.13 m Gun Assy (0338 or 0407)-1D11-12D (120 shots) 132 in. 3.35 m Gun Assy (0338 or 0407)-1D21-12D (240 shots) 252 in. 6.40 m Tandem Shoulder Length - Wireline (TCP Grooved): 1.38 in. (3.25 in.) 35.05 mm (82.55 mm) Gun End to First Scallop Distance: 7.00 in. 177.80 mm Calculated Break Point Tensile Strength - Hardware Only (8): 952,000 lbs. 4,233,000 N Maximum Rockwell “C” Hardness (Hardware Only): 39 39 Minimum Recommended Casing Size (9): 8-5/8 in. 219.1 mm Minimum Recommended Casing Weight: 28.0 lbs/ft 41.71 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ RDX (11): T.B.D. (12) T.B.D. (12) Maximum Charge Explosive Load - Ambient Fluid (Wet) (10): T.B.D. (12) T.B.D. (12) Maximum (Average) Test Gun Swell @ 32g RDX (11): 7.073 in. (7.065 in.) 179.65 mm (179.45 mm) Minimum Recommended I.D. Running Restriction: 7.386 in. 187.60 mm Minimum Recommended Washover Pipe Clearance Requirements:


Vertical Drop Test (14): T.B.D. (12) T.B.D. (12) Horizontal Drop Test (14): T.B.D. (12) T.B.D. (12) Estimated Gun Assy Weight without Explosives: 36.4 lbs/ft 54.1 kg/m Estimated Gun Assy Weight with BH Charges (15): 53.2 lbs/ft 79.2 kg/m Estimated Gun Assy Weight with DP Charges (15): 67.0 lbs/ft 99.6 kg/m 101920071626

GENERAL COMMENTS Expendable Casing Gun Systems












only. 9. The minimum casing size/weight recommendation assumes that the casing is in good condition and fully

supported. 10. Gun integrity is dependent upon the gun material toughness as measured by the Transverse Charpy “V” Notch

Impact Test (Reference ASTM E23), and must be 50 ft/lbs or greater. 11. Maximum and average gun swell measurements shown herein were taken from laboratory guns containing steel


12. T.B.D. is an acronym for “To Be Determined”. 13. Value shown is the difference between the two diameters. 14. Vertical and horizontal drop test data contained herein does not imply that a gun is safe to run down hole if





3 1/8” E.E.G. CASING GUN SYSTEM

4 SPF - 60° PHASE

Charge Arrangement: LOW SHOT DENSITY, SEQUENTIAL Gun Body Material: Steel Gun Body Configuration: Threaded & Unscalloped Charge Positioning Method: Twisted Strip or Round Steel Tube Conveyance Methods: Wireline Mode Of Fire: Simultaneous Type of Tandem Connection (1): Lap Splice Gun Positioning Requirements: Optional Initiation Point: Gun Series 0631 - Wireline Style BOTTOM Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 2 5/8” - 8 STUB ACME O-ring Material (2): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-229 ENGLISH METRIC Nominal Gun Outside Diameter: 3.125 in. 79.38 mm Nominal Gun Body Wall Thickness: .300 in. 7.62 mm Maximum Shot Density: 4 spf 13 spm Angular Phasing - Charge to Charge: 60º 60º Angular Phasing - Bank to Bank: 60º 60º Vertical Charge Spacing: 3.00 in. 25.4 mm Vertical Planes Perforated per Repeat Shot Pattern: 6 6 Horizontal Planes Perforated per Repeat Shot Pattern: 6 6 Minimum Recommended Cord Velocity Of Detonation: 21,000 ft/sec 6,400 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (3,4,5): 500º F 260º C Pressure Rating (3): 7,500 psi 51.71 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 2.475 in. (10 in.) 62.86 mm (254 mm) Standard Overall Gun Lengths (6): Gun Assy Tube (Strip) 0631-A04 (A404)-046 (12 shots) 48 in. 1.22 m Gun Assy Tube (Strip) 0631-A07 (A407)-046 (24 shots) 84 in. 2.13 m Gun Assy Tube (Strip) 0631-A11 (A411)-046 (40 shots) 132 in. 3.35 m Gun Assy Tube (Strip) 0631-A21 (A421)-046 (80 shots) 252 in. 6.40 m Gun Assy Tube (Strip) 0631-A26 (A426)-046 (100 shots) 312 in. 7.92 m Gun Assy Tube (Strip) 0631-A31 (A431)-046 (120 shots) 372 in. 9.45 m ** Customized gun lengths available upon request. ** Minimum Recommended Casing Size (7): 4-1/2 in. 114.3 mm Minimum Recommended Casing Weight (7): 9.50 lbs/ft 14.16 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry): NOT RECOMMENDED NOT RECOMMENDED Maximum (Average) Test Gun Swell @ RDX (8): NOT RECOMMENDED NOT RECOMMENDED Maximum Charge Explosive Load - Ambient Fluid (Wet): T.B.D. (11) T.B.D. (11) Maximum (Average) Test Gun Swell @ RDX (8): T.B.D. (11) T.B.D. (11) Minimum Recommended I.D. Running Restriction: 3.58 in. 90.93 mm Minimum Recommended Washover Pipe Clearance Requirements: Casing Drift Diameter-to-Nominal Washover Pipe O.D. .375 in. 9.53 mm Washover Pipe Drift Diameter-to-Nominal Gun O.D. .313 in. 7.95 mm Estimated Gun Assy Weight without Explosives: 10.4 lbs/ft 15.5 kg/m Estimated Gun Assy Weight with DP Charge (10): 11.0 lbs/ft 16.4 kg/m Estimated Gun Assy Weight with BH Charge (10): T.B.D. (11) T.B.D. (11) 092420090939



4 SPF - 90° PHASE

Charge Arrangement: LOW SHOT DENSITY, SEQUENTIAL Gun Body Material: Steel Gun Body Configuration: Threaded & Unscalloped Charge Positioning Method: Twisted Strip or Round Steel Tube Conveyance Methods: Wireline Mode Of Fire: Simultaneous Type of Tandem Connection (1): Lap Splice Gun Positioning Requirements: Optional Initiation Point: Gun Series 0631 - Wireline Style BOTTOM Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 2 5/8” - 8 STUB ACME O-ring Material (2): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-229 ENGLISH METRIC Nominal Gun Outside Diameter: 3.125 in. 79.38 mm Nominal Gun Body Wall Thickness: .300 in. 7.62 mm Maximum Shot Density: 4 spf 13 spm Angular Phasing - Charge to Charge: 90º 90º Angular Phasing - Bank to Bank: 90º 90º Vertical Charge Spacing: 3.00 in. 25.4 mm Vertical Planes Perforated per Repeat Shot Pattern: 4 4 Horizontal Planes Perforated per Repeat Shot Pattern: 4 4 Minimum Recommended Cord Velocity Of Detonation: 21,000 ft/sec 6,400 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (3,4,5): 500º F 260º C Pressure Rating (3): 7,500 psi 51.71 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 2.475 in. (10 in.) 62.86 mm (254 mm) Standard Overall Gun Lengths (6): Gun Assy Tube (Strip) 0631-A04 (A404)-044 (12 shots) 48 in. 1.22 m Gun Assy Tube (Strip) 0631-A07 (A407)-044 (24 shots) 84 in. 2.13 m Gun Assy Tube (Strip) 0631-A11 (A411)-044 (40 shots) 132 in. 3.35 m Gun Assy Tube (Strip) 0631-A21 (A421)-044 (80 shots) 252 in. 6.40 m Gun Assy Tube (Strip) 0631-A26 (A426)-044 (100 shots) 312 in. 7.92 m Gun Assy Tube (Strip) 0631-A31 (A431)-044 (120 shots) 372 in. 9.45 m ** Customized gun lengths available upon request. ** Minimum Recommended Casing Size (7): 4-1/2 in. 114.3 mm Minimum Recommended Casing Weight (7): 9.50 lbs/ft 14.16 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry): NOT RECOMMENDED NOT RECOMMENDED Maximum (Average) Test Gun Swell @ RDX (8): NOT RECOMMENDED NOT RECOMMENDED Maximum Charge Explosive Load - Ambient Fluid (Wet): 19.0 g RDX/HMX 19.0g RDX/HMX Maximum (Average) Test Gun Swell @ 19.0g RDX (8): 3.392 in. (3.346 in.) 86.16 mm (84.99 mm) Minimum Recommended I.D. Running Restriction: 3.58 in. 90.93 mm Minimum Recommended Washover Pipe Clearance Requirements: Casing Drift Diameter-to-Nominal Washover Pipe O.D. .375 in. 9.53 mm Washover Pipe Drift Diameter-to-Nominal Gun O.D. .313 in. 7.95 mm Estimated Gun Assy Weight without Explosives: 10.4 lbs/ft 15.5 kg/m Estimated Gun Assy Weight with DP Charge (10): 11.0 lbs/ft 16.4 kg/m Estimated Gun Assy Weight with BH Charge (10): T.B.D. (11) T.B.D. (11) 092420090940



4 SPF - 120° PHASE

Charge Arrangement: LOW SHOT DENSITY, SEQUENTIAL Gun Body Material: Steel Gun Body Configuration: Threaded & Unscalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline Mode Of Fire: Simultaneous Type of Tandem Connection (1): Lap Splice Gun Positioning Requirements: Optional Initiation Point: Gun Series 0631 - Wireline Style BOTTOM Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 2 5/8” - 8 STUB ACME O-ring Material (2): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-229 ENGLISH METRIC Nominal Gun Outside Diameter: 3.125 in. 79.38 mm Nominal Gun Body Wall Thickness: .300 in. 7.62 mm Maximum Shot Density: 4 spf 13 spm Angular Phasing - Charge to Charge: 120º 120º Angular Phasing - Bank to Bank: 120º 120º Vertical Charge Spacing: 3.00 in. 25.4 mm Vertical Planes Perforated per Repeat Shot Pattern: 3 3 Horizontal Planes Perforated per Repeat Shot Pattern: 3 3 Minimum Recommended Cord Velocity Of Detonation: 21,000 ft/sec 6,400 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (3,4,5): 500º F 260º C Pressure Rating (3): 7,500 psi 51.71 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 2.475 in. (10 in.) 62.86 mm (254 mm) Standard Overall Gun Lengths (6): Gun Assy 0631-C04-043 (12 shots) 48 in. 1.22 m Gun Assy 0631-C07-043 (24 shots) 84 in. 2.13 m Gun Assy 0631-C11-043 (40 shots) 132 in. 3.35 m Gun Assy 0631-C21-043 (80 shots) 252 in. 6.40 m Gun Assy 0631-C26-043 (100 shots) 312 in. 7.92 m Gun Assy 0631-C31-043 (120 shots) 372 in. 9.45 m ** Customized gun lengths available upon request. ** Minimum Recommended Casing Size (7): 4-1/2 in. 114.3 mm Minimum Recommended Casing Weight (7): 9.50 lbs/ft 14.16 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry): NOT RECOMMENDED NOT RECOMMENDED Maximum (Average) Test Gun Swell @ RDX (8): NOT RECOMMENDED NOT RECOMMENDED Maximum Charge Explosive Load - Ambient Fluid (Wet): 19.0 g RDX/HMX 19.0g RDX/HMX Maximum (Average) Test Gun Swell @ RDX (8): T.B.D. (11) T.B.D. (11) Minimum Recommended I.D. Running Restriction: 3.58 in. 90.93 mm Minimum Recommended Washover Pipe Clearance Requirements: Casing Drift Diameter-to-Nominal Washover Pipe O.D. .375 in. 9.53 mm Washover Pipe Drift Diameter-to-Nominal Gun O.D. .313 in. 7.95 mm Estimated Gun Assy Weight without Explosives: 10.4 lbs/ft 15.5 kg/m Estimated Gun Assy Weight with DP Charge (10): 11.0 lbs/ft 16.4 kg/m Estimated Gun Assy Weight with BH Charge (10): T.B.D. (11) T.B.D. (11) 092420090941



6 SPF - 60° PHASE

Charge Arrangement: MEDIUM SHOT DENSITY, SEQUENTIAL Gun Body Material: Steel Gun Body Configuration: Threaded & Unscalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline Mode Of Fire: Simultaneous Type of Tandem Connection (1): Lap Splice Gun Positioning Requirements: Optional Initiation Point: Gun Series 0631 - Wireline Style BOTTOM Fired Recommended Detonating Cord: 80 grains/foot Thread Description: 2 5/8” - 8 STUB ACME O-ring Material (2): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-229 ENGLISH METRIC Nominal Gun Outside Diameter: 3.125 in. 79.38 mm Nominal Gun Body Wall Thickness: .300 in. 7.62 mm Maximum Shot Density: 6 spf 19 spm Angular Phasing - Charge to Charge: 60º 60º Angular Phasing - Bank to Bank: 60º 60º Vertical Charge Spacing: 2.00 in. 50.8 mm Vertical Planes Perforated per Repeat Shot Pattern: 6 6 Horizontal Planes Perforated per Repeat Shot Pattern: 6 6 Minimum Recommended Cord Velocity Of Detonation: 22,000 ft/sec 6,700 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (3,4,5): 500º F 260º C Pressure Rating (3): 7,500 psi 51.71 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 2.475 in. (10 in.) 62.86 mm (254 mm) Standard Overall Gun Lengths (6): Gun Assy 0631-B04-066 (18 shots) 48 in. 1.22 m Gun Assy 0631-B07-066 (36 shots) 84 in. 2.13 m Gun Assy 0631-B11-066 (60 shots) 132 in. 3.35 m Gun Assy 0631-B21-066 (120 shots) 252 in. 6.40 m Gun Assy 0631-B26-066 (150 shots) 312 in. 7.92 m Gun Assy 0631-B31-066 (180 shots) 372 in. 9.45 m ** Customized gun lengths available upon request. ** Minimum Recommended Casing Size (7): 4-1/2 in. 114.3 mm Minimum Recommended Casing Weight (7): 9.50 lbs/ft 14.16 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry): NOT RECOMMENDED NOT RECOMMENDED Maximum (Average) Test Gun Swell @ RDX (8): NOT RECOMMENDED NOT RECOMMENDED Maximum Charge Explosive Load - Ambient Fluid (Wet): 15.0g RDX/HMX 15.0g RDX/HMX Maximum (Average) Test Gun Swell @ 14g RDX (8): 3.297 in. (3.262 in.) 83.7 mm (82.9 mm) Minimum Recommended I.D. Running Restriction: 3.58 in. 90.93 mm Minimum Recommended Washover Pipe Clearance Requirements: Casing Drift Diameter-to-Nominal Washover Pipe O.D. .375 in. 9.53 mm Washover Pipe Drift Diameter-to-Nominal Gun O.D. .313 in. 7.95 mm Estimated Gun Assy Weight without Explosives: 10.4 lbs/ft 15.5 kg/m Estimated Gun Assy Weight with DP Charge (10): 12.2 lbs/ft 18.1 kg/m Estimated Gun Assy Weight with BH Charge (10): T.B.D. (11) T.B.D. (11) 092420090942


4” E.E.G. CASING GUN SYSTEM

4 SPF - 60° PHASE

Charge Arrangement: LOW SHOT DENSITY, SEQUENTIAL Gun Body Material: Steel Gun Body Configuration: Threaded & Unscalloped Charge Positioning Method: Twisted Strip or Round Steel Tube Conveyance Methods: Wireline Mode Of Fire: Simultaneous Type of Tandem Connection (1): Lap Splice Gun Positioning Requirements: Optional Initiation Point: Gun Series 0640 - Wireline Style BOTTOM Fired (Top Fire W/L system pending) Recommended Detonating Cord: 80 grains/foot Thread Description: 3 1/2” - 6 Stub ACME O-ring Material (2): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-236 ENGLISH METRIC Nominal Gun Outside Diameter: 4.00 in. 101.6 mm Nominal Gun Body Wall Thickness: .318 in. 8.08 mm Maximum Shot Density: 4 spf 13 spm Angular Phasing - Charge to Charge: 60º 60º Angular Phasing - Bank to Bank: 60º 60º Vertical Charge Spacing: 3.00 in. 76.2 mm Vertical Planes Perforated per Repeat Shot Pattern: 6 6 Horizontal Planes Perforated per Repeat Shot Pattern: 6 6 Minimum Recommended Cord Velocity Of Detonation: 21,000 ft/sec 6,400 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (3,4,5): 500º F 260º C Pressure Rating (3): 7,500 psi 51.71 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 3.315 in. (10 in.) 84.20 mm (254 mm) Standard Overall Gun Lengths (6): Gun Assy Tube (Strip) 0640-B04 (A406)-046 (12 shots) 48 in. 1.22 m Gun Assy 0640-B07-046 (A407)-046 (24 shots) 84 in. 2.13 m Gun Assy 0640-B11-046 (A411)-046 (40 shots) 132 in. 3.35 m Gun Assy 0640-B16-046 (A416)-046 (60 shots) 192 in. 4.88 m Gun Assy 0640-B21-046 (A421)-046 (80 shots) 252 in. 6.40 m Gun Assy 0640-B26-046 (A426)-046 (100 shots) 312 in. 7.92 m Gun Assy 0640-B31-046 (A431)-046 (120 shots) 372 in. 9.45 m ** Customized gun lengths available upon request. ** Minimum Recommended Casing Size (7): 5-1/2 in. 139.7 mm Minimum Recommended Casing Weight (7): 14.0 lbs/ft 20.4 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry): T.B.D. (11) T.B.D. (11) Maximum (Average) Test Gun Swell @ RDX (8): T.B.D. (11) T.B.D. (11) Maximum Charge Explosive Load - Ambient Fluid (Wet): T.B.D. (11) T.B.D. (11) Maximum (Average) Test Gun Swell @ RDX (8): T.B.D. (11) T.B.D. (11) Minimum Recommended I.D. Running Restriction: 4.767 in. 121.1 mm Minimum Recommended Washover Pipe Clearance Requirements:


Estimated Gun Assy Weight without Explosives: 13.7 lbs/ft 20.4 kg/m Estimated Gun Assy Weight with DP Charge (10): 16.6 lbs/ft 24.6 kg/m Estimated Gun Assy Weight with BH Charge (10): T.B.D. (11) T.B.D. (11) 092420090934



4 SPF - 90° PHASE

Charge Arrangement: LOW SHOT DENSITY, SEQUENTIAL Gun Body Material: Steel Gun Body Configuration: Threaded & Unscalloped Charge Positioning Method: Twisted Strip or Round Steel Tube Conveyance Methods: Wireline Mode Of Fire: Simultaneous Type of Tandem Connection (1): Lap Splice Gun Positioning Requirements: Optional Initiation Point: Gun Series 0640 - Wireline Style BOTTOM Fired (Top Fire W/L system pending) Recommended Detonating Cord: 80 grains/foot Thread Description: 3 1/2” - 6 Stub ACME O-ring Material (2): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-236 ENGLISH METRIC Nominal Gun Outside Diameter: 4.00 in. 101.6 mm Nominal Gun Body Wall Thickness: .318 in. 8.08 mm Maximum Shot Density: 4 spf 13 spm Angular Phasing - Charge to Charge: 90º 90º Angular Phasing - Bank to Bank: 90º 90º Vertical Charge Spacing: 3.00 in. 76.2 mm Vertical Planes Perforated per Repeat Shot Pattern: 4 4 Horizontal Planes Perforated per Repeat Shot Pattern: 4 4 Minimum Recommended Cord Velocity Of Detonation: 21,000 ft/sec 6,400 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (3,4,5): 500º F 260º C Pressure Rating (3): 7,500 psi 51.71 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 3.315 in. (10 in.) 84.20 mm (254 mm) Standard Overall Gun Lengths (6): Gun Assy Tube (Strip) 0640-B04 (A404)-044 (12 shots) 48 in. 1.22 m Gun Assy Tube (Strip) 0640-B07 (A407)-044 (24 shots) 84 in. 2.13 m Gun Assy Tube (Strip) 0640-B11 (A411)-044 (40 shots) 132 in. 3.35 m Gun Assy Tube (Strip) 0640-B16 (A416)-044 (60 shots) 192 in. 4.88 m Gun Assy Tube (Strip) 0640-B21 (A421)-044 (80 shots) 252 in. 6.40 m Gun Assy Tube (Strip) 0640-B26 (A426)-044 (100 shots) 312 in. 7.92 m Gun Assy Tube (Strip) 0640-B31 (A431)-044 (120 shots) 372 in. 9.45 m ** Customized gun lengths available upon request. ** Minimum Recommended Casing Size (7): 5-1/2 in. 139.7 mm Minimum Recommended Casing Weight (7): 14.0 lbs/ft 20.4 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry): 26.0g RDX/HMX 26.0g RDX/HMX Maximum (Average) Test Gun Swell @ 26.0g RDX (8): 4.50 in. 114.3 mm Maximum Charge Explosive Load - Ambient Fluid (Wet): 32.0g RDX/HMX 32.0g RDX/HMX Maximum (Average) Test Gun Swell @ 32.0g RDX (8): 4.50 in. 114.3 mm Minimum Recommended I.D. Running Restriction: 4.767 in. 121.1 mm Minimum Recommended Washover Pipe Clearance Requirements:


Estimated Gun Assy Weight without Explosives: 13.7 lbs/ft 20.4 kg/m Estimated Gun Assy Weight with DP Charge (10): 16.6 lbs/ft 24.6 kg/m Estimated Gun Assy Weight with BH Charge (10): T.B.D. (11) T.B.D. (11) 092420090916



6 SPF - 60° PHASE

Charge Arrangement: MEDIUM SHOT DENSITY, SEQUENTIAL Gun Body Material: Steel Gun Body Configuration: Threaded & Unscalloped Charge Positioning Method: Round Steel Tube Conveyance Methods: Wireline Mode Of Fire: Simultaneous Type of Tandem Connection (1): Lap Splice Gun Positioning Requirements: Optional Initiation Point: Gun Series 0640 - Wireline Style BOTTOM Fired (Top Fire W/L system pending) Recommended Detonating Cord: 80 grains/foot Thread Description: 3 1/2” - 6 Stub ACME O-ring Material (2): Peroxide Cured Nitrile - 90 Durometer O-ring Size: 568-236 ENGLISH METRIC Nominal Gun Outside Diameter: 4.00 in. 101.6 mm Nominal Gun Body Wall Thickness: .318 in. 8.08 mm Maximum Shot Density: 6 spf 19 spm Angular Phasing - Charge to Charge: 60º 60º Angular Phasing - Bank to Bank: 60º 60º Vertical Charge Spacing: 2.00 in. 50.8 mm Vertical Planes Perforated per Repeat Shot Pattern: 6 6 Horizontal Planes Perforated per Repeat Shot Pattern: 6 6 Minimum Recommended Cord Velocity Of Detonation: 22,000 ft/sec 6,700 m/sec Maximum 1 Hour Operating Temperature - Hardware Only (3,4,5): 500º F 260º C Pressure Rating (3): 7,500 psi 51.71 MPa Drift Gauge O.D. For Gun Body (Gauge Length): 3.315 in. (10 in.) 84.20 mm (254 mm) Standard Overall Gun Lengths (6): Gun Assy 0640-B04-066 (18 shots) 48 in. 1.22 m Gun Assy 0640-B07-066 (36 shots) 84 in. 2.13 m Gun Assy 0640-B11-066 (60 shots) 132 in. 3.35 m Gun Assy 0640-B16-066 (90 shots) 192 in. 4.88 m Gun Assy 0640-B21-066 (120 shots) 252 in. 6.40 m Gun Assy 0640-B26-066 (150 shots) 312 in. 7.92 m Gun Assy 0640-B31-066 (180 shots) 372 in. 9.45 m ** Customized gun lengths available upon request. ** Minimum Recommended Casing Size (7): 5-1/2 in. 139.7 mm Minimum Recommended Casing Weight (7): 14.0 lbs/ft 20.4 kg/m Maximum Charge Explosive Load - Ambient Gas (Dry): 22.7g RDX/HMX 22.7g RDX/HMX Maximum (Average) Test Gun Swell @ 22.7g RDX (8): 4.495 in. (4.410 in.) 114.7 mm (112.01 mm) Maximum Charge Explosive Load - Ambient Fluid (Wet): 26.0g RDX/HMX 26.0g RDX/HMX Maximum (Average) Test Gun Swell @ 26.0g RDX (8): T.B.D. (11) T.B.D. (11) Minimum Recommended I.D. Running Restriction: 4.767 in. 121.1 mm Minimum Recommended Washover Pipe Clearance Requirements: Casing Drift Diameter-to-Nominal Washover Pipe O.D. .375 in. 9.53 mm Washover Pipe Drift Diameter-to-Nominal Gun O.D. .375 in. 9.53 mm Estimated Gun Assy Weight without Explosives: 13.7 lbs/ft 19.9 kg/m Estimated Gun Assy Weight with DP Charge (10): 17.6 lbs/ft 26.2 kg/m Estimated Gun Assy Weight with BH Charge (10): T.B.D. (11) T.B.D. (11) 092420090931

GENERAL COMMENTS 3 1/8” & 4” E.E.G. Casing Gun System

This document is for informational purposes only and is intended to aid the user in the decision making process. The information contained herein represents typical, average values obtained in accordance with accepted test methods/procedures and are subject to normal manufacturing variations. Translation of said data to downhole conditions is the responsibility of the service company/customer. This document is supplied as a technical service and is subject to change without notice. Check with Titan Specialties to assure current information. FOOTNOTES 1. Explosive transfer reliability between guns can be affected by the condition of the hardware, type and quality of









6. Customized gun lengths are available to 31 feet. 7. The minimum casing size/weight recommendation assumes that the casing is in good condition and fully

supported. 8. Maximum and average gun swell measurements shown herein were taken from surface tested, laboratory guns

containing steel backed charges. Gun swell experienced downhole may differ dramatically depending upon numerous factors such as fluid environment, pressure, temperature, gun clearance, charge case material, charge liner material, charge manufacturer, etc..

9. Value shown is the difference between the two diameters. 10. Estimated gun assembly weight with DP or BH charges will vary depending upon the type of charge. Value shown

is the combined weight of the gun body, end fittings, fully loaded charge tube, detonating cord, miscellaneous small hardware items, and charges from one charge manufacturer.

11. T.B.D. is an acronym for “To Be Determined”.

Documents

Perforating GunFacts™castellmx.com/pdf/gunfacts.pdf · Perforating GunFacts™ 1-11/16” SEMI EXPENDABLE THRU TUBING GUN 4 SPF - 0º PHASE Charge Arrangement: LOW SHOT DENSITY,