Operating Instructionsstatic1.projectorpoint.co.uk/.../sony/vpl-vw200/sony_vpl-vw200-manual.… · Operating Instructions VPL-VW200 3-275-583-13 (1)D:\WORK\VW60GB\3275583131\3275583131VPLVW200UC\00COV_

Operating Instructions

VPL-VW2003-275-583-13 (1)

D:\WORK\VW60GB\3275583131\3275583131VPLVW200UC\00COV_VPLVW200UC\01COV.fm

masterpage:BackCover

VPL-VW200

© 2007 Sony Corporation

3-275-583-13 (1)

Video Projector

D:\WORK\VW60GB\3275583131\3275583131VPLVW200UC\010GB_VPLVW200UC\01REG.fm

masterpage:Left

WARNING

To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

For customers in the USAIf you have any questions about this product, you may call:Sony Customer Information Service Center1-800-222-7669 or http://www.sony.com/The number below is for FCC related matters only.

Declaration of ConformityTrade Name: SONYModel No.: VPL-VW200Responsible Party: Sony Electronics Inc.Address: 16530 Via Esprillo, San Diego, CA 92127 U.S.A.Telephone Number: 858-942-2230

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the

equipment and receiver.- Connect the equipment into an outlet on a

circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

2

VPL-VW2003-275-583-13 (1)


masterpage:Left

Disposal of Used LampThis projector’s lamp should be disposed of properly. Consult your local authorities regarding safe disposal.The material contained in this lamp are similar to those of a fluorescent lamp, so you should dispose of it in the same way.

For customers in EuropeThe manufacturer of this product is Sony Corporation, 1-7-1 Konan Minato-ku Tokyo, 108-0075 Japan. The Authorized Representative for EMC and product safety is Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany. For any service or guarantee matters please refer to the addresses given in separate service or guarantee documents.

Trademark InformationSXRD, “BRAVIA” and , Motionflow, “x.v.Color” are trademarks of Sony Corporation.

HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

“Blu-ray Disc” is a trademark.

3

VPL-VW2003-275-583-13 (1)


masterpage:Left

For customers in CanadaThis Class B digital apparatus complies with Canadian ICES-003.

For customers in EuropeDisposal of waste batteries (applicable in the European Union and other European countries with separate collection systems)

This symbol on the battery or on the packaging indicates that the battery provided with this product shall not be treated as household waste.By ensuring these batteries are disposed of correctly, you will help prevent potentially negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of the battery. The recycling of the materials will help to conserve natural resources.In case of products that for safety, performance or data integrity reasons require a permanent connection with an incorporated battery, this battery should be replaced by qualified service staff only.To ensure that the battery will be treated properly, hand over the product at end-of-life to the applicable collection point for the recycling of electrical and electronic equipment.For all other batteries, please view the section on how to remove the battery from the product safely. Hand the battery over to the applicable collection point for the recycling of waste batteries.For more detailed information about recycling of this product or battery, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product.

For customers in Taiwan only

The socket-outlet should be installed near the equipment and be easily accessible.

CAUTIONRISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.DISPOSED OF USED BATTERIES ACCORDING TO THE LOCAL RULES.

Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems)This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product.

4

VPL-VW2003-275-583-13 (1)

D:\WORK\VW60GB\3275583131\3275583131VPLVW200UC\010GB_VPLVW200UC\02COVTOC.fm

masterpage:Left

Table of Contents

Precautions .........................................7

Front/Right Side .................................8

Rear/Bottom .......................................9

Remote Control ................................10

Unpacking ........................................11

Step 1: Installing the Projector .........12

Before Setting Up the Projector .....................................12

Connecting the AC Power Cord ..........................................14

Positioning the Projector and a screen ..........................................15

Step 2: Connecting the Projector .....18

Connecting to a VCR .................18

Connecting to a Computer ..........21

Step 3: Adjusting the Picture Position .............................................22

Step 4: Selecting the Menu Language ..........................................26

Projecting the Picture on the Screen ...............................................28

Turning Off the Power ...............29

Selecting the Wide Screen Mode .....30

Selecting the Picture Viewing Mode ...............................................32

Adjusting the Picture Quality ...........33

Selecting to directly adjust the desired menu item ......................33

Selecting desired adjust menu items in the order ....................... 34

Adjusting the Picture Using Real Color Processing .............................. 35

Using the Supplied Software to Adjust the Picture Quality (ImageDirector3) ............................. 36

Operation through the Menus .......... 37

Picture Menu ................................... 41

Advanced Picture Menu .................. 45

Screen Menu .................................... 46

Setup Menu ...................................... 48

Function Menu ................................. 50

Installation Menu ............................. 52

Information Menu ............................ 55

About the Preset Memory No. ... 55

Accessing the Projector from a Computer ......................................... 56

Checking the Status of the Projector .......................................... 56

Operating the Projector .................... 57

Setting the Information .................... 57

Location of Controls

Connections and Preparations

Projecting

Using the Menus

Operating the Projector from a Computer

5

VPL-VW2003-275-583-13 (1)

D:\WORK\VW60GB\3275583131\3275583131VPLVW200UC\010GB_VPLVW200UC\02COVTOC.fm

masterpage:Left

About the HDMI Control ................. 59

About the x.v.Color ......................... 59

Troubleshooting ............................... 60

Warning Indicators ..................... 62

Message Lists ............................. 63

Replacing the Lamp and the Air Filter and cleaning the Ventilation holes (intake) ................. 65

Cleaning the Air Filter ..................... 70

Cleaning and the Screen of the Projector ........................................... 70

Specifications ................................... 71

Preset Signals ............................. 73

Input Signals and Adjustable/Setting Items ............................... 76

Ceiling Installation ........................... 78

When Using the PSS-H10 Projector Suspension Support .... 78

Making Fine Adjustments to the Horizontal Picture Position .............. 82

Index ............................................... 85

Others

6

VPL-VW2003-275-583-13 (1)

D:\WORK\VW60GB\3275583131\3275583131VPLVW200UC\010GB_VPLVW200UC\03CAU.fm

masterpage:Left

7

VPL-VW2003-275-583-13 (1)

Precautions

On safety• Check that the operating voltage of your

unit is identical with the voltage of your local power supply.

• Should any liquid or solid object fall into the cabinet, unplug the unit and have it checked by qualified personnel before operating it further.

• Unplug the unit from the wall outlet if it is not to be used for several days.

• To disconnect the cord, pull it out by the plug. Never pull the cord itself.

• The wall outlet should be near the unit and easily accessible.

• The unit is not disconnected to the AC power source (mains) as long as it is connected to the wall outlet, even if the unit itself has been turned off.

• Do not look into the lens while the lamp is on.

• Do not place your hand or objects near the ventilation holes. The air coming out is hot.

On preventing internal heat build-up After you turn off the power with the I/1 (ON/STANDBY) switch, do not disconnect the unit from the wall outlet while the cooling fan is still running.

CautionThe projector is equipped with ventilation holes (intake) and ventilation holes (exhaust). Do not block or place anything near these holes, or internal heat build-up may occur, causing picture degradation or damage to the projector.

On repackingSave the original shipping carton and packing material; they will come in handy if you ever have to ship your unit. For maximum protection, repack your unit as it was originally packed at the factory.

D:\WORK\VW60GB\3275583131\3275583131VPLVW200UC\010GB_VPLVW200UC\04GET.fm

masterpage:Left

Front/Right SideYou can use the buttons on the control panel with the same names as those on the remote control to operate the projector.


INPUT button (1 page 28)

MENU button (1 page 37)

ON/STANDBY indicator (1 page 22)

LENS button (1 page 23)

Remote control detector (1 page 22)

Ventilation holes (intake) (1 page 13)

?/1 (ON/STANDBY) switch (1 page 22)

LAMP/COVER indicator (1 page 62)

M/m/


masterpage:Left


Rear/Bottom

Remote control detector (1 page 22)

Filter holder (1 page 68)


Cover release lever (1 page 65)

Top cover (1 page 65)

Projector suspension support attachment holes (1 page 78)

Adjusters (1 page 25)


Ventilation holes (exhaust) (1 page 13)

9

VPL-VW2003-275-583-13 (1)


masterpage:Left

Remote Control

COLOR TEMP button(1 page 33)

BLACK LEVEL button(1 page 33)

RESET button(1 page 37)

ADVANCED IRIS button(1 page 33)

RCP (Real Color Processing) button(1 page 35)

BRIGHTNESS +/– button(1 page 42)

ADJUST PICTURE button (1 page 34)

PICTURE MODEbuttons (1 page 32)

INPUT button(1 page 28)

COLOR SPACE button(1 page 33)

GAMMA CORRECTIONbutton (1 page 33)

M/m/

D:\WORK\VW60GB\3275583131\3275583131VPLVW200UC\010GB_VPLVW200UC\05PRE.fm

masterpage:Left

Connections and P

reparations

This section describes how to install the projector and screen, how to connect the equipment from which you want to project the picture, etc.

UnpackingCheck the carton to make sure it contains the following items:

Inserting the batteries into the remote control

Caution about handling the remote control• Handle the remote control with care. Do not drop or step on it, or spill liquid of any kind

onto it.• Do not place the remote in a location near a heat source, a place subject to direct

sunlight, or a damp room.

Connections and Preparations

• Remote control (1)• Size AA (R6) batteries (2)• AC power cord (1)• ImageDirector3 CD-ROM (1)• Plug holder

Attach the plug holder to avoid unplugging the AC power cord accidentally. (1 page 14)

• Air filter cover (1)This air filter cover is used only when the projector is installed on a ceiling. (1 page 78)

• Lens cap (1)When you have purchased the projector, the lens cap is put onto the lens. Remove this lens cap when you use the projector.

• Operating Instructions (this manual)

Insert the batteries E side first as shown in the illustration.Inserting them forcibly or with the polarities reversed may cause a short circuit and may generate heat.Push and slide to open.

11

VPL-VW2003-275-583-13 (1)


masterpage:Left

Step 1: Installing the ProjectorThe projector displays pictures output from a VCR or other device.The lens shift allows you to have broader options for placing the projector and viewing pictures easily.

Unsuitable installationDo not place the projector in the following situations, which may cause malfunction or damage to the projector.

Poorly ventilated location

Leave space of more than 20 cm (7 7/8 inches) around the unit.

Hot and humid

Locations subject to direct cool or warm air from an air-conditioner

Installing the projector in such a location may cause a malfunction of the unit due to moisture condensation or rise in temperature.

Near a heat or smoke sensor

Malfunction of the sensor may occur.

Very dusty and extremely smoky locations

Install in a location away from walls

To maintain the performance and reliability of the projector, allow at least 20 cm (7 7/8 inches) between the projector and walls. Note that the wall on the rear side of the projector may become extremely hot.

Before Setting Up the Projector

20 cm(7 7/8 inches)

20 cm

(7 7/8 inches)

20 cm

(7 7/8 inches)

20 cm(7 7/8 inches)

: Exhaust

12

VPL-VW2003-275-583-13 (1)


masterpage:Left

Connections and P

reparations

Improper useDo not do any of the following while using the projector.

Blocking the ventilation holes.

TipFor details on the location of the ventilation holes (intake or exhaust), see “Location of Controls” on pages 8 to 9.

Tilting front/rear and left/right

Avoid using the projector tilted at an angle of more than 15 degrees.Do not install the projector anywhere other than on a level surface or on the ceiling. Failing to set this mode when using the projector at high altitudes may result in uneven color uniformity and reducing the reliability of the effects of the lamp.

When installing the unit at altitudesWhen using the projector at an altitude of 1,500 m or higher, set “Cooling Setting” in the Setup

menu to “High” (1 page 48). Failing to set this mode when using the projector at high altitudes could have adverse effects, such as reducing the reliability of certain components.

Ventilation holes (intake)

Ventilation holes (exhaust)

15° or more

15° or more

15° or more

15° or more

15° or more

13

VPL-VW2003-275-583-13 (1)


masterpage:Left

Connecting the AC Power Cord

1 Plug the AC power cord into the AC IN socket (power connector) of the projector. Then, attach the plug holder to the AC power cord.

2 Slide the plug holder over the cord until it locks.

To remove the AC power cordPull out the AC power cord while pressing both sides of the lock levers of the plug holder.

Plug holder

AC power cord

AC IN socket

14

VPL-VW2003-275-583-13 (1)


masterpage:Left

Connections and P

reparations

The installation distance between the projector and a screen varies depending on the size of the screen.

1 Determine the installation position of the projector and screen.You can obtain a good quality picture if you position the projector with the center of the lens within the areas indicated in the gray areas in the illustration. Use the values a, b and c in the table on page 16 as a guide.

a: Minimum projection distance between the screen and the center of the projector’s lens

b: Maximum projection distance between the screen and the center of the projector’s lens

c: Vertical distance between the center of the screen and the center of the projector’slens when using the maximum upper vertical lens shift feature.

For installation of the projector on a ceiling, see “Ceiling Installation.” (1 page 78)For details on the lens shift feature, see “Step 3: Adjusting the Picture Position.” (1 page 22)

Positioning the Projector and a screen

Center of projector’s lens

a

b

c

Center of the screen

c

Ceiling installation

Floor installation

15

VPL-VW2003-275-583-13 (1)


masterpage:Left

When using the 16:9 aspect ratio screenUnit: mm (inches)

To calculate the installation measurements (SS: Screen Size)a (minimum) = 31.5 (1 1/4) × SS – 48.2 (1 15/16)b (maximum) = 53.8 (2 1/8) × SS – 46.9 (1 7/8)c = 8.0876 (11/32) × SS

When using the 4:3 aspect ratio screen (projecting a 4:3 picture)Unit: mm (inches)

To calculate the installation measurements (SS: Screen Size)a (minimum) = 38.551 (1 9/16) × SS – 48.2 (1 15/16)b (maximum) = 65.842 (2 5/8) × SS – 46.9 (1 7/8)c = 9.8979 (13/32) × SS

Screen size (inches)

40 60 80 100 120 150 180 200 250 300

(mm) 1016 1524 2032 2540 3048 3810 4572 5080 6350 7620

a (minimum)

1212(47 3/4)

1842(72 5/8)

2472(97 3/8)

3102(122 1/4)

3732(147)

4677(184 1/4)

5622(221 3/8)

6252(246 1/4)

7827(308 1/4)

9402(370 1/4)

b (maximum)

2105(82 7/8)

3181(125 1/4)

4257(167 5/8)

5333(210)

6409(252 3/8)

8023(315 7/8)

9637(379 1/2)

10713(421 7/8)

13403(527 5/8)

16093(633 5/8)

c 324(12 7/8)

485(19 1/8)

647(25 1/2)

809(31 7/8)

971(38 1/4)

1213(47 7/8)

1456(57 3/8)

1618(63 3/4)

2022(79 5/8)

2426(95 5/8)

Screen size (inches)

40 60 80 100 120 150 180 200 250 300

(mm) 1016 1524 2032 2540 3048 3810 4572 5080 6350 7620

a (minimum)

1494(58 7/8)

2265(89 1/4)

3036(119 5/8)

3807(150)

4578(180 1/4)

5734(225 3/4)

6891(271 3/8)

7662(301 3/4)

9590(377 5/8)

11517(453 1/2)

b (maximum)

2587(101 7/8)

3904(153 3/4)

5220(205 5/8)

6537(257 3/8)

7854(309 1/4)

9829(387)

11805(464 7/8)

13122(516 5/8)

16414(646 1/4)

19706(775 7/8)

c 396(15 5/8)

594(23 1/2)

792(31 1/4)

990(39)

1188(46 7/8)

1485(58 1/2)

1782(70 1/4)

1980(78)

2474(97 1/2)

2969(117)

16

VPL-VW2003-275-583-13 (1)


masterpage:Left

Connections and P

reparations

2 Position the projector so that the lens is parallel to the screen.

3 Project an image on the screen and adjust the picture so that it fits the screen. (1 page 22)To project an image, connect video equipment to the projector. (1 page 18)

When using a screen with an uneven surface, stripes pattern may rarely appear on the screen depending on the distance between the screen and the projector or the zooming magnifications. This is not a malfunction of the projector.

Note

Screen

Top view

17

VPL-VW2003-275-583-13 (1)


masterpage:Left

Step 2: Connecting the ProjectorWhen making connections, be sure to do the following:• Turn off all equipment before making any connections.• Use the proper cables for each connection.• Insert the cable plugs properly; poor connection at the plugs may cause a malfunction or

poor picture quality. When pulling out a cable, be sure to pull it out from the plug, not the cable itself.

• Refer to the operating instructions of the connected equipment.

To connect to a DVD player/recorder, Blu-ray Disc player or digital tuner equipped with component video connectors

Connecting to a VCR

Component video cable (not supplied)

: Video signal flow

DVD player/recorder, HDD recorder, Blu-ray Disc player, digital tuner, etc., with component video connectors

Right side of the projectorAV amplifier

Speakers

18

VPL-VW2003-275-583-13 (1)


masterpage:Left

Connections and P

reparations

To connect to a DVD player/recorder or Blu-ray Disc player equipped with HDMI outputYou can enjoy better picture quality by connecting a DVD player/recorder or Blu-ray Disc player equipped with HDMI output to the HDMI input of the projector. Moreover, if you have an HDMI control compatible equipment, you can operate the projector synchronizing with the HDMI control compatible equipment. For details, see the Function

menu (1 page 50) and “About the HDMI Control” (1 page 59).

• When connecting equipment to the HDMI input of the projector, be sure to use equipment that have acquired the HDMI logo.

• When connecting an HDMI cable to the projector, make sure the V mark on the upper part of the HDMI input of the projector and the V mark on the connector of the cable is set at the same position.

• If the picture from equipment connected to the projector with an HDMI cable is not clear, check the settings of the connected equipment.

Notes

HDMI cable (not supplied)

: Video signal flow

Right side of the projector

DVD player/recorder or Blu-ray Disc player, etc., with the HDMI output

to HDMI output

AV amplifier Speakers

When using an optional HDMI cable, be sure to use a cable that has acquired the HDMI logo.

.............................................................................................................................................................HDMI Control is an HDMI standard mutual control function which uses the HDMI CEC (Consumer Electronics Control) specification.This projector supports DeepColor, x.v.Color, LipSync, and PC Display input of HDMI standards. It also supports HDCP.

19

VPL-VW2003-275-583-13 (1)


masterpage:Left

To connect to a VCR equipped with the S video connector or video connectorYou can connect a DVD player/recorder, hard disk video recorder, VCR or laser disk player, which is not equipped with component video connectors. See also the instruction manual of each equipment.

TipIf you do not know to which connector you should connect the cable, S VIDEO INPUT (S video input connector) or VIDEO INPUT (video input connector), connect it to S VIDEO to enjoy better picture quality.If the equipment to be connected has no S video connector, connect the cable to the video output.

S video or video cable (not supplied)

: Video signal flow


to S video or video output

Video equipment

AV amplifierSpeakers

20

VPL-VW2003-275-583-13 (1)


masterpage:Left

Connections and P

reparations

TipSet “Input-A Signal Sel.” in the Setup menu to “Auto.” If the input signal does not appear properly, set it to “Computer.” (1 page 49, 63)

• When connecting an HDMI cable, make sure the V mark on the upper part of the HDMI input of the projector and the V mark on the connector of the cable is set at the same position.

• If you set your computer, such as a notebook type, to output the signal to both computer’s display and this equipment, the picture of the equipment may not appear properly. Set your computer to output the signal to only the external monitor.For details, refer to the computer’s operating instructions supplied with your computer. For settings of the computer, consult with the manufacturer of the computer.

• If the picture from equipment connected to the projector with an HDMI cable is not clear, check the settings of the connected equipment.

Connecting to a Computer

Notes

HD-Dsub15 pin cable (not supplied) or HDMI cable (not supplied)

: Video signal flow


to monitor output

Computer

When using an optional HDMI cable, be sure to use a cable that has acquired the HDMI logo.

21

VPL-VW2003-275-583-13 (1)


masterpage:Left

Step 3: Adjusting the Picture PositionProject an image on the screen and then adjust the picture position.

TipThe ?/1 (ON/STANDBY), INPUT, LENS, MENU, and M/m/


masterpage:Left

Connections and P

reparations

Tips• You can select the desired language for the menu screen. For details, refer to “Step 4: Selecting

the Menu Language”. (1 page 26)• When “Auto Input Search” is set to “On” in the Function menu, the input terminal with

effective signals is automatically displayed by pressing INPUT. (1 page 50)

TipWhen “Lens Control” is set to “Off” on the Installation menu, you cannot adjust the vertical picture position. (1 page 52)When “Test Pattern” is set to “Off” on the Function menu, the test pattern is not displayed. (1 page 51)

3 Turn on the equipment connected to the projector.Refer to the operating instructions of the connected equipment.

4 Press INPUT to project the picture on the screen. Each time you press the button, the input indication and equipment to be projected change. (1 page 28)

5 Adjust the vertical picture position.Press the LENS button repeatedly until the Lens Shift adjustment window (test pattern) appears. Then select the proper vertical position by pressing the M/m/


masterpage:Left

The picture moves up by a maximum of 65% of the screen size from the center of the lens.

TipYou can also adjust the horizontal position of the lens. For detailed information, see “Making Fine Adjustments to the Horizontal Picture Position” on page 82.

6 Adjust the picture size.Press the LENS button repeatedly until the Lens Zoom adjustment window (test pattern) appears. Then adjust the size of the picture by pressing the M/m/


masterpage:Left

Connections and P

reparations

TipWhen “Lens Control” is set to “Off” on the Installation menu, you cannot adjust the picture size and the focus. (1 page 52)When “Test Pattern” is set to “Off” on the Function menu, the test pattern is not displayed. (1 page 51)

To adjust the tilt of the installation surfaceIf the projector is installed on an uneven surface, use the adjusters to keep the projector level.

Be careful not to catch your finger when turning the adjusters.

7 Adjust the focus.Press the LENS button repeatedly until the Lens Focus adjustment window (test pattern) appears. Then adjust the focus of the picture by pressing the M/m/


masterpage:Left

Step 4: Selecting the Menu LanguageYou can select one of 16 languages for displaying the menu and other on-screen displays. The factory default setting is English. To change the current menu language, set the desired language with the menu screen.

1 Press MENU.The menu appears.

1

2,3,4

26

VPL-VW2003-275-583-13 (1)


masterpage:Left

Connections and P

reparations

2 Press M/m to select the Setup

menu, and press , or .The setting items of the selected menu appears.

3 Press M/m to select “Language,” and press , or .

4 Press M/m/

D:\WORK\VW60GB\3275583131\3275583131VPLVW200UC\010GB_VPLVW200UC\06PRO.fm

masterpage:Left

This section describes how to operate the projector to view the picture from the equipment connected to the projector. It also describes how to adjust the quality of the picture to suit your taste.

Projecting the Picture on the Screen

* Set the “Input-A Signal Sel.” setting in the Setup menu according to the signal input. When you set it to “Auto,” and cannot display the picture properly, select an appropriate signal according to the input signal. (1 page 49, 55)

** Make the setting on the equipment connected with HDMI cable according to the HDMI standards.The color gradation of the dark area or the bright area may become unclear, or texts may become faded when a signal other than those from HDMI standard is input. Adjusting the “Brightness” and the “Contrast”, or adjusting the “Sharpness” in the Picture menu may improve these conditions. (1 page 42)

Projecting

1 Power on both the equipment and the device connected to the equipment.

2 Press INPUT repeatedly to select the input you want to project on the screen.Display the indication of the input you want.

Example: To view the picture from the video equipment connected to the VIDEO INPUT connector.

To view the picture from Press INPUT to display

Video equipment connected to the VIDEO INPUT connector Video

Video equipment connected to S VIDEO INPUT connector S-Video

Component equipment connected to Y PB/CB PR/CR on the projector Component

RGB/component equipment connected to the INPUT A connector Input-A*

Equipment connected to the HDMI 1 connector HDMI1**

Equipment connected to the HDMI 2 connector HDMI2**

28

VPL-VW2003-275-583-13 (1)


masterpage:Left

Projecting

Tips• When “Auto Input Search” is set to “On” in the Function menu, the input terminal with

effective signals is automatically displayed by pressing INPUT.• When the “HDMI Control” is set to “On” in the Function menu, the input terminal with

effective signals is automatically displayed, synchronizing with the operation of the equipment connected to HDMI 1 or HDMI 2 input of the projector.

1 Press the ?/1 (ON/STANDBY) switch.A message “POWER OFF?” appears on the screen.

2 Press the ?/1 (ON/STANDBY) switch again before the message disappears.The ON/STANDBY indicator flashes in green and the fan continues to run to reduce the internal heat. First, the ON/STANDBY indicator flashes quickly, during which you will not be able to light up the ON/STANDBY indicator with the ?/1 (ON/STANDBY) switch.

3 Confirm that the fan stops running and the ON/STANDBY indicator lights in red.

You can turn off the projector by holding the ?/1 (ON/STANDBY) switch for about one second, instead of performing the above steps.

TipWhen the projector is connected to an HDMI control compatible equipment, the HDMI control compatible equipment synchronizes with the operation of the projector. When you turn the power of the projector off, the power of the HDMI control compatible equipment will also turn off.

Turning Off the Power

29

VPL-VW2003-275-583-13 (1)


masterpage:Left

Selecting the Wide Screen ModeYou can enjoy various wide screen modes according to the video signal received.

Press WIDE MODE.Each time you press the button, you can select the “Wide Mode” setting.You can also select it using the menu. (1 page 46)

Wide ZoomA 4:3 aspect ratio picture is enlarged over the entire screen properly. The upper and lower portions of the screen are slightly cut off.

NormalA picture with normal 4:3 aspect ratio is displayed in the center of the screen to fill the vertical screen size.

FullA picture squeezed to 4:3 is displayed with the correct aspect ratio. A 4:3 picture is enlarged horizontally to fit the 16:9 screen.

TipSqueezed: An original 16:9 aspect ratio picture is recorded horizontally compressed to a 4:3 picture.

WIDE MODE button

Original image When the Wide Mode is operated

Squeezed

30

VPL-VW2003-275-583-13 (1)


masterpage:Left

Projecting

You can adjust the vertical position of the picture with “V Center” and “Vertical Size” in the Screen menu only when “Zoom” is selected. (1 page 47)

Notes on selecting the wide screen modeThe projector is featured with the WIDE MODE. When changing the settings of WIDE MODE, use caution as described below.• Select the wide screen mode taking into account that changing the aspect ratio of the

original picture will provide a different look from that of the original image.• Note that if the projector is used for profit or for public viewing, modifying the original

picture by switching to the wide mode may constitute an infringement of the rights of authors or producers, which are legally protected.

ZoomA normal 16:9 aspect ratio picture is enlarged vertically and horizontally in the same ratio to fill the screen. Use this mode to view a letterbox picture or a letterbox picture with side panels.If the subtitle of a movie, etc. is hidden and cannot be seen, adjust the screen with “Vertical Size” and “V Center” to display the subtitle. (1 page 47)

Anamorphic ZoomA 2.35:1 aspect ratio picture is converted to a normal 16:9 picture on the screen. This mode is best suited when using a commercially available Anamorphic lens which converts a normal 16:9 aspect ratio picture to a 2.35:1 picture.

Full1 (When the PC signal is input)Displays a picture on the whole of the screen without changing the aspect ratio of the original picture.

Full2 (When the PC signal is input)Displays a picture on the whole of the screen.

Note

Letterbox picture with side panels

Letterbox picture

When using an Anamorphic lens

31

VPL-VW2003-275-583-13 (1)


masterpage:Left

Selecting the Picture Viewing ModeYou can select the picture viewing mode that best suits the type of program or room conditions.

Press one of the PICTURE MODE buttons (DYNAMIC, STANDARD, CINEMA and USER 1, USER 2 and USER 3).

DYNAMICEnhances picture contrast and sharpness.

STANDARDThe quality of the picture becomes less rough than the one selected by “DYNAMIC”.

CINEMARecommended when viewing a movie in the dark place.

USER 1, USER 2 and USER 3You can adjust the quality of the picture to suit your taste and store the settings into the selected memory of the projector. Press one of the USER 1, USER 2 and USER 3 buttons, then adjust the picture by using the buttons on the remote control or the menus (1 pages 33, 41). The settings are stored, and you can view the picture with the adjusted picture quality by pressing the button.

PICTURE MODE buttons DYNAMIC STANDARD CINEMA USER 1, USER 2

and USER 3

32

VPL-VW2003-275-583-13 (1)


masterpage:Left

Projecting

Adjusting the Picture QualityYou can easily adjust the picture quality that suits your taste by selecting the adjustment items with the remote control. The adjusted data can be stored in each picture mode.

Selecting to directly adjust the desired menu item

COLOR SPACE buttonAdjusts the range of color reproduction on the screen.Each time you press the button, the setting is switched either to “Normal” or “Wide” to change the range of color reproduction on the screen.

COLOR TEMP buttonEach time you press the button, the setting of the button is changed in the order of “High,” “Middle,” “Low,” “Custom1,” “Custom2”, “Custom3”.

BLACK LEVEL buttonEach time you press the button, the setting of the button is changed in the order of “High”, “Low”, “Off”.

FILM PROJECTION buttonEach time you press the button, the setting of “Film Projection” is changed in the order of “Mode1”, “Mode2”, “Mode3” and “Off”.

ADVANCED IRIS buttonAdjusts the desired iris when projecting a picture.Each time you press the button, the setting of the button is changed in the order of “Auto1”, “Auto2”, “Manual” and “Off”.

GAMMA CORRECTION buttonEach time you press the button, the setting of the button is changed in the order of “Gamma1”, “Gamma2”, “Gamma3”, and “Off”.

BLACK LEVEL button

GAMMA CORRECTION button

COLOR SPACE button

ADVANCED IRIS button

COLOR TEMP button

FILM PROJECTION button

33

VPL-VW2003-275-583-13 (1)


masterpage:Left

Selecting desired adjust menu items in the order

1 Press ADJUST PICTURE.Each time you press the button, the following adjustment windows are displayed in sequence.

For details on each adjustment, see the Picture menu. (1 page 41)

Some adjustment windows cannot be displayed, depending on the type of input signal. For details, see “Input Signals and Adjustable/Setting Items” (1 page 76)

2 Make the setting or adjustment on an item.

When changing the adjustment levelTo increase the value, press ,.To decrease the value, press


masterpage:Left

Projecting

Adjusting the Picture Using Real Color ProcessingThe Real Color Processing (RCP) feature allows you to adjust the color and hue of each target of the projected picture you specify independently. You can thus obtain a picture more suitable to your taste.

TipFreeze the scene of the video source when you are adjusting the picture using Real Color Processing.

1 Press RCP on the remote control.

2 Press M/m to select “User1,” “User2” or “User3,” then press ,.The RCP (Real Color Processing) window appears.

3 Select the target color you want to adjust.Repeat steps 1 and 2 described below to specify the target color.

1 Press M/m to select “Color Select,” then press


masterpage:Left

Using the Supplied Software to Adjust the Picture Quality (ImageDirector3)By using the “ImageDirector3” (supplied as a CD-ROM), you can make the desired gamma correction from a computer connected to the projector. Connect the REMOTE or the NETWORK connector of the projector with a computer and start-up “ImageDirector3” on the computer.For details on how to use the “ImageDirector3”, refer to the Help within the CD-ROM.

• You need to install the “ImageDirector3” on a computer beforehand.• When connecting the REMOTE connector or the NETWORK connector with a

computer, connect while the power of the computer and the projector are off.

2 Press M/m to select “Position” or “Range,” and specify it more delicate color position and color range you want to adjust using

D:\WORK\VW60GB\3275583131\3275583131VPLVW200UC\010GB_VPLVW200UC\07MEN.fm

masterpage:Left

Using the M

enus

This section describes how to make various adjustments and settings using the menus.

Operation through the MenusThe projector is equipped with an on-screen menu for making various adjustments and settings. Some of the adjustable/setting items are displayed in a pop-up menu, in a setting menu or adjustment menu with no main menu, or in the next menu window. If you select an item name followed by an arrow (B), the next menu window with setting items appears.To change the on-screen menu language, see “Step 4: Selecting the Menu Language.” (1 page 26)

Using the Menus

2, 3, 4

1

RESET button

37

VPL-VW2003-275-583-13 (1)


masterpage:Left

1 Press MENU.The menu window appears.

2 Press M/m to select a menu item, and press , or .The items that can be set or adjusted with the selected menu appear. The item presently selected is shown in yellow.

38

VPL-VW2003-275-583-13 (1)


masterpage:Left

Using the M

enus

3 Press M/m to select an item you

want to set or adjust and press , or .The setting items are displayed in a pop-up menu, in a setting menu, in an adjustment menu or in the next menu window.

Pop-up menu

Setting items

Next menu windowSetting items

Setting menu

Adjustment menu

39

VPL-VW2003-275-583-13 (1)


masterpage:Left

4 Make the setting or adjustment of an item.

When changing the adjustment levelTo increase the value, press M/,.To decrease the value, press m/


masterpage:Left

Using the M

enus

Picture MenuThe Picture menu is used for adjusting the picture.

Picture Mode You can select the picture viewing mode that best suits the type of picture or the environment.Dynamic: Select this for enhanced picture contrast and sharpness to

reproduce color tones.Standard: Select this to reduce roughness compared to viewing the

picture with “Dynamic”.Cinema: Select this for watching movies, etc. in a dark environment.User1, User2, User3: You can adjust the quality of the picture to suit

your taste and then store the settings. Once the settings are stored, you can view the picture with the adjusted picture quality by pressing the PICTURE MODE button on the remote control.

To store the settings1 Select User1, User2, or User3.2 Adjust the items you want in the menus.

Tips• You can also adjust the picture quality in “Dynamic”, “Standard” or

“Cinema”, and store the settings. To reset everything to the factory settings, select “Reset” from the menu.

• Some items may not be displayed on the Picture menu, depending on the type of input signal. For details, see “Input Signals and Adjustable/Setting Items” (1 page 76).

Cinema Black Pro Advanced IrisSwitches the iris function during projection.Auto1: Automatically switches to an optimum iris according to a

projected scene. The contrast of the scene is emphasized most.Auto2: An optimum iris becomes smaller than when set to “Auto1”. The

contrast of the scene becomes reduced.Sensitivity: If “Auto1” or “Auto2” is selected, either “Recommend”,

“Fast”, or “Slow” can be selected according to the desired response speed with Sensitivity Mode.

Manual: Manually adjusts the Iris.

Off: Normal contrast.

41

VPL-VW2003-275-583-13 (1)


masterpage:Left

Motionflow Film ProjectionReproduces movies in its original moving picture.Mode1: Best suited for watching movies.Mode2: Suited for watching movies. The picture is brighter than in

“Mode1”.Mode3: Suited for watching movies. The picture is brighter than in

“Mode2”. Off: Normal picture.

When you select “Mode1”or “Mode2”, the picture will become slightly darker than in “Off”.

Motion EnhancerReproduces fast-moving pictures smoothly without generating afterimages.High: Select this for picture quality smoother than “Low”.Low: Select this for smooth picture quality.Off: Select “Off” when noise, etc. appears in “High” or “Low”. Usually,

set “Motion Enhancer” to “Off”.

Contrast Adjusts the white area of pictures (white level).The higher the setting, the greater the contrast. The lower the setting, the lower the contrast.You can make adjustments by pressing the CONTRAST+/– on the remote control.

Brightness Adjusts the brightness of the picture.The higher the setting, the brighter the picture. The lower the setting, the darker the picture.You can make adjustments by pressing the BRIGHTNESS+/– on the remote control.

Color Adjusts the intensity of the color density.The higher the setting, the greater the intensity. The lower the setting, the lower the intensity.

Hue Adjusts the color tone.The higher the setting, the more greenish the picture becomes. The lower the setting, the more reddish the picture becomes.

Color Temp. Adjusts the color temperature.High: Gives white colors a blue tint.Middle: Gives a neutral tint between “High” and “Low”.Low: Gives white colors a red tint.Custom1, Custom2, Custom3: Enables you to adjust, set, and store

your favorite color temperature.

Sharpness Sharpens the outline of the picture, or reduces the noise.The higher the setting, the sharper the picture. The lower the setting, the softer the picture, thus reducing the noise.You can make adjustments by pressing the SHARPNESS+/– on the remote control.

Note

42

VPL-VW2003-275-583-13 (1)


masterpage:Left

Using the M

enus

Expert Setting NR (Noise Reduction)

Reduces the roughness or noise of the picture.Usually, select “Off”.If the picture is rough or noisy, select a setting from among “Low”, “Middle” or “High” according to the input signal source.

DRC ModeSets the picture quality to be best suited for the input signal.Mode 1: Select this for sharp picture from input signal without side

panel information, etc.Mode 2: Select this for sharp picture from input signal with side panel

information, etc.Off: Does not convert the input signal to DRC.

Depending on the input signal, the picture quality of “Mode1”and “Mode2” may not differ.DRC Palette: You can adjust the “Reality” and “Clarity” of a picture as

desired on the DRC palette when selecting “Mode 1” or “Mode 2”.

To increase the value for “Clarity,” press the , button.To decrease the value for “Clarity,” press the < button.To increase the value for “Reality,” press the M button.To decrease the value for “Reality,” press the m button.

Film ModeReproduces 2-3 or 2-2 Pull-Down film sources with smooth picture movement.Auto1: Automatically detects the 2-3 or 2-2 Pull-Down format and

performs film conversion. Smooth moving picture is emphasized than in “Auto2”.

Auto2: Automatically detects the 2-3 or 2-2 Pull-Down format and performs film conversion.

Off: Does not detect the 2-3 or 2-2 Pull-Down format.

Black Level Adj. (Adjust)Produces a bolder, dynamic picture.Set according to the input signal source.High: Gives higher emphasis to the black color.Low: Gives lower emphasis to the black color.Off: Cancels this feature.

Depending on the setting of x.v.Color, this item cannot be set.

Note

Note

43

VPL-VW2003-275-583-13 (1)


masterpage:Left

Gamma CorrectionAdjusts the response characteristics of the tone of the picture.Select a favorite tone from three options.Gamma1: Makes a scene a little brighter.Gamma2: Makes a scene brighter.Gamma3: Makes a scene darker.Off: Gamma Correction is “Off”Using the specified controller, “ImageDirector3” (supplied as a CD-ROM) allows you to adjust, set, and store a favorite tone in a computer.For detailed information on “ImageDirector3”, refer to the Help provided on the supplied CD-ROM in the computer.

Depending on the setting of x.v.Color, this item cannot be set.

x.v.ColorSet this item when playing back an x.v.Color video signal.Set this item to “On” when connecting the projector with equipment that supports x.v.Color and playing back an x.v.Color video signal.For details on x.v.Color, see “About the x.v.Color” (1 page 59).

Note

44

VPL-VW2003-275-583-13 (1)


masterpage:Left

Using the M

enus

Advanced Picture MenuThe Advanced Picture is used for adjusting the picture more.

RCP (Real Color Processing)

You can adjust the color and hue of each selected portion of the picture independently.User1, User2, User3: You can adjust the picture using Real Color

Processing and store the settings. Once the settings are stored, you can view the picture with the adjusted picture quality.

Off: Cancels this feature.For details, see “Adjusting the Picture Using Real Color Processing”.

(1 page 35)

Color Space You can convert the range of color reproduction.Normal: Converts the color to Hi-Vision color.Wide: Reproduces more natural color tones in a wider range of color

reproduction, compared to “Normal”.

45

VPL-VW2003-275-583-13 (1)


masterpage:Left

Screen MenuThe Screen menu is used to adjust the input signal. You can adjust the size of the picture, and select wide screen mode, etc..

Wide Mode (When the image input signal is input)

You can set the aspect ratio of the picture to be displayed for the current input signal. This item is enabled only when an image signal (preset memory numbers 1 to 14) (1 page 73, 74) is input.Wide Zoom: A 4:3 aspect ratio picture is enlarged over the entire screen

properly. The upper and lower portions of the screen are slightly cut off.

Normal: A picture with normal 4:3 aspect ratio is displayed in the center of the screen to fill the vertical screen size.

Full: A picture squeezed to 4:3 is displayed with the correct aspect ratio. A 4:3 picture is enlarged horizontally to fit the 16:9 screen.

Zoom: A normal 16:9 aspect ratio picture is enlarged vertically and horizontally in the same ratio to fill the screen.

Anamorphic Zoom: A 2.35:1 aspect ratio picture is converted to a normal 16:9 picture on the screen. This mode is best suited when using a commercially available Anamorphic lens which converts a normal 16:9 aspect ratio picture to a 2.35:1 picture.

Wide Mode (When the PC signal is input)

You can set the aspect ratio of the picture to be displayed for the current input signal. This item is enabled only when an PC signal is input.Full1: Displays a picture on the whole of the screen without changing

the aspect ratio of the original picture.Full2: Displays a picture on the whole of the screen.Zoom: A normal 16:9 aspect ratio picture is enlarged vertically and

horizontally in the same ratio to fill the screen.

Over Scan Hides the outline of the picture.On: Hides the outline of the input picture. Select this setting when noise

appears along the edge of the picture.Off: Projects the whole of the input picture.

TipTo display the displayable region within the four directions of the screen, refer to “Blanking” on the Installation menu (1 page 53).

46

VPL-VW2003-275-583-13 (1)


masterpage:Left

Using the M

enus

Screen Area Selects the size of the picture when a Hi-Vision picture is

overscanned.Full: Expands the picture on the whole of the screen.Through: Does not expands the picture on the whole of the screen.

This item is effective only when a Hi-Vision signal (preset memory No. 7, 8, 9, 12, 13 and 14) is input and “On” is selected in “Over Scan”.

V Center Adjust the whole picture by moving up and down on the screen.As the selected number increases, the screen moves up, and as the selected number decreases, the screen moves down.

This item is adjustable only when “Zoom” is selected.

Vertical Size Reduces or enlarges the picture vertically. The screen is enlarged as the setting increases and reduced as the setting decreases. If the subtitle of a movie, etc. cannot be seen, use this together with “V Center”.

This item is adjustable only when “Zoom” is selected.

Adjust Signal You can adjust the input signal.APA: Adjusts the position of the image signal automatically for

“Phase”, “Pitch”, and “Shift”.Phase: Adjusts the dot phase of the panel and the computer signal.

Adjust the picture to the point where it looks clearest.Pitch: Adjusts the horizontal size of the picture from a computer.

The higher the setting, the wider the picture. The lower the setting, the narrower the picture. Adjust the setting to match the number of dots of the input signal.

Shift: Adjusts the position of the picture.H: As the setting for H (horizontal) increases, the picture moves

to the right, and as the setting decreases, the picture moves to the left. Use < / , to adjust the horizontal position.

V: As the setting for V (vertical) increases, the picture moves up, and as the setting decreases, the picture moves down. Use M / m to adjust the vertical position.

Note

Note

Note

47

VPL-VW2003-275-583-13 (1)


masterpage:Left

Setup MenuThe Setup menu is used to change the factory preset settings, etc.

Status Sets whether or not the on-screen display is displayed.Set to “Off” to turn off the on-screen displays except for the menus, message when turning off the power, and warning messages.

Language Selects the language used in the menu and on-screen displays. Available languages are: English, Dutch, French, Italian, German, Spanish, Portuguese, Russian, Swedish, Norwegian, Japanese, Chinese (Simplified Chinese), Chinese (Traditional Chinese), Korean, Thai and Arabic.

Cooling Setting Use this item when using the projector at high altitudes.High: Use this setting when using the projector at an altitude of

1,500 m or higher.Standard: Use this setting when using the projector at normal

altitudes.

When this item is set to “High”, the fan noise becomes slightly louder since the number of fan rotation increases.

Standby Mode Sets to lower the power consumption in standby.Standard1: Sets power consumption to normal.Standard2: Sets the network function ineffective and reduces power

consumption lower than “Standard1”.Low: Reduces power consumption lower than “Standard2”.

When this item is set to “Low”, the HDMI Control function and the network function will not operate in standby.

Power Saving Sets the power saving mode.When set to “On”, the projector goes into power saving mode if no signal is input for 10 minutes. At that time, the ON/STANDBY indicator lights in orange, then the screen becomes dark. In power saving mode, the power saving mode is cancelled if a signal is input or any button is pressed. If you do not want to set the projector to power saving mode, select “Off”.

Note

Note

48

VPL-VW2003-275-583-13 (1)


masterpage:Left

Using the M

enus

Input-A Signal Sel. Selects the type of signal input from the equipment connected to

the INPUT A connector.Selects the type of signal input from the equipment by selecting “Input-A” with the INPUT button.Auto: Selects the input signal type automatically.Computer: Inputs the signal from a computer.Video GBR: Inputs the signal from a TV game.Component: Inputs the component signal from a DVD player/

recorder, Blu-ray Disc player, digital tuner, etc.

When the input signal is not displayed correctly with this item set to “Auto,” select the item according to the input signal.

Color System Selects the color system of the input signal.Auto: Selects the color system of the input signal automatically

from among NTSC3.58, PAL, SECAM, NTSC4.43, PAL-M, PAL-N, or PAL60.

“NTSC3.58”–“PAL-N”: Allows you to set the color system to the selected system manually.

Normally, set this to “Auto.” If the picture is distorted or colorless, select the color system appropriate for the input signal.

Lamp Setting When replacing the lamps, set the desired lamp setting. (1 page 69)

Note

Note

49

VPL-VW2003-275-583-13 (1)


masterpage:Left

Function MenuThe Function menu is used for changing the settings of the various functions of the projector.

HDMI Control Selects the function whether to turn the HDMI Control function effective, when the HDMI 1 INPUT and HDMI 2 INPUT connectors are connected to a HDMI control compatible equipment.HDMI Control: When set to “On”, the HDMI Control function is

turned effective and the following settings can be assigned.PJ→HDMI Power Sync: When set to on “On”, the projector is

powered off while the HDMI control compatible equipment connected to the projector is also powered off at the same time.

HDMI→PJ Power Sync: When set to “On”, the HDMI control compatible equipment connected to the projector is automatically powered on or played back, etc., while the projector is also powered on at the same time.

HDMI Device List: Lists all the HDMI control compatible equipment connected to the HDMI 1 and HDMI 2 INPUT connectors of the projector.

• When “Standby Mode” is set to “Low”, this item will not operate.• To operate the connected equipment, be sure the equipment is

HDMI control compatible and assign the appropriate settings to use the HDMI Control function.For details, see “About the HDMI Control” (1 page 59).

Auto Input Search Detects the input signal and displays the detected input signal automatically when the INPUT button is pressed.When set to “On”, the projector detects whether a Component, HDMI 1, HDMI 2, Video, S-video or Input-A signal is input when the input terminal with effective signals is automatically selected by pressing INPUT. Set this to “Off” when you want to select an input selector with no input signal, or you want to switch the setting manually.

Notes

50

VPL-VW2003-275-583-13 (1)


masterpage:Left

Using the M

enus

Test Pattern Displays the test pattern.

When set to “On,” a test pattern appears on the screen to be used when adjusting the lens with “Lens Focus,” “Lens Zoom,” and “Lens Shift,” or correcting the screen proportions with “V Keystone.” A test pattern does not appear when this item is set to “Off.”

TipWhile the test pattern is displayed, it is only displayed in green to allow you to adjust the focus easily.

Background Selects the background color of the screen when no signal is input.You can select “Black” or “Blue”.

51

VPL-VW2003-275-583-13 (1)


masterpage:Left

Installation MenuThe Installation menu is used for changing the installation settings.

V Keystone Corrects the vertical trapezoidal distortion of the picture.When the bottom of the trapezoid is longer than the top ( ):

Sets a lower value (– direction) When the top of the trapezoid is longer than the bottom ( ):

Sets a higher value (+ direction).

Depending on the picture position adjusted with the lens shift feature, the aspect ratio of the picture may change from the original or picture distortion may occur with V Keystone adjustment.

Image Flip Flips the picture on the screen horizontally and/or vertically. Off: The picture does not flip.HV: Flips the picture horizontally and vertically.H: Flips the picture horizontally. V: Flips the picture vertically.Use this item for installation for the backside projection or ceiling installation.

Lens Control Avoids any operation of the lens such as “Lens Focus,” “Lens Zoom,” and “Lens Shift,” by mistake.When set to “On,” you can adjust the projection lens using “Lens Focus,” “Lens Zoom,” and “Lens Shift.” After you make this adjustment, it is recommended that you set this item to “Off” to avoid any operation of the lens.

IR Receiver Selects the remote control detectors (IR Receiver) on the front and rear of the projector. Front & Rear: Activates both the front and rear detectors.Front: Activates the front detector only.Rear: Activates the rear detector only.

Illumination Selects whether the illumination on the top panel of the projector lights when the projector is on. Turns on the illumination on the top panel of the projector, when set to “On.” It turns off when set to “Off.”

Note

52

VPL-VW2003-275-583-13 (1)


masterpage:Left

Using the M

enus

Blanking This feature allows you to adjust the displayable region within

the four directions of the screen.Select each screen edge “Left / Right / Top / Bottom” on the Blanking adjustment screen with M / m buttons. Adjust the desired Blanking value with < / , button.

When both the “Blanking” and the “V Keystone” are adjusted at the same time, the “Blanking” cannot be adjusted correctly. When using the “Blanking”, make sure that you set the “V Keystone” to “0”.

Panel Alignment This feature allows you to adjust the gaps in the color of characters or the picture.When set to “On”, the “Adjust Color” and the “Pattern Color” can be assigned and adjusted. Adjust Item: Selects how to make adjustments from below.

Shift: Shifts the whole picture and makes adjustments.Zone: Selects the desired range and makes adjustments.

Adjust Color: Assigns the desired color to adjust the gaps in color. Select “R” (Red) or “B” (Blue) to make adjustments based on “G” (Green).

Pattern Color: Select “R/G” (Red and Green) or “R/G/B” (White, all colors) when the “Adjust Color” is “R” (Red). Select “B/G” (Blue and Green) or “R/G/B” (White, all colors) when the “Adjust Color” is “B” (Blue).

Adjust: The shift adjustment and zone adjustment of the color selected in “Adjust Color” can be made with < / ,, M / m buttons.

When “Shift” is selected: Assign the settings of the horizontal direction (H) with < / , buttons and the vertical direction (V) with M / m buttons on the shift adjustment screen.

When “Zone” is selected: Select the position to adjust with < / , buttons for the horizontal position (H position) and M / m buttons for the vertical position (V position), then press .

Note

53

VPL-VW2003-275-583-13 (1)


masterpage:Left

Set the amount to adjust with < / , buttons for the horizontal direction (H direction) and with M / m buttons for the vertical direction (V direction). You can select the position to adjust again by pressing .

Reset: Returns to the factory settings.

Depending on the adjustments made above, colors may become uneven or the resolution may change.

Network Setting You can set internet protocols such as IP address, Subnet Mask, Default Gateway, and DNS Server when accessing the projector from a computer or using “ImageDirector3”application supplied. IP Address SetupSelects either “Auto (DHCP)” or “Manual.” When you select “Manual,” set the following “IP Address,” “Subnet Mask,” and “Default Gateway.” After completing all of settings, select “Apply” using m button, then press .IP AddressSets the IP Address of the projector.(1.0.0.0 to 223.255.255.255)Subnet MaskSets the Subnet Mask of the projector.(1.0.0.0 to 255.255.255.255)Default GatewaySets the Default Gateway of the projector.(1.0.0.0 to 223.255.255.255)Primary DNSSets the DNS server to be used as a priority.(1.0.0.0 to 223.255.255.255)Secondary DNSSets the alternative DNS server.(1.0.0.0 to 223.255.255.255)MAC AddressDisplays MAC address of the projector. You cannot change.

Note

54

VPL-VW2003-275-583-13 (1)


masterpage:Left

Using the M

enus

Information MenuThe Information menu displays the model name, serial number, the horizontal and vertical frequencies of the input signal and the cumulated hours of usage of the lamp.

• fH (horizontal frequency) and fV (vertical frequency) may not be displayed depending on the equipment connected to the projector.

• You cannot change the displays listed above.

This projector has 38 types of preset data for input signals (the preset memory). When the preset signal is input, the projector automatically detects the signal type and recalls the data for the signal from the preset memory to adjust it to an optimum picture. The memory number and signal type of that signal are displayed in the Information menu.You can also adjust the preset data through the Screen menu.This projector also contains 20 different user memories beside the preset memories used for inputting analog computer signals. You can save input signals that have not been preset on these user memories.When an unpreset signal is input for the first time, a memory number is displayed as 0. When you adjust the data of the signal in the Screen menu, it will be registered to the projector. If more than 20 user memories are registered, the newest memory always overwrites the oldest one.See the chart on page 73 to find if the signal is registered to the preset memory.

When the aspect ratio of input signal does not match the screen size, a part of the screen is displayed in black.

Model Name Displays the model name (VPL-VW200).

Serial No. Displays the serial number.

fH (horizontal frequency) Displays the horizontal frequency of the input signal.

fV (vertical frequency) Displays the vertical frequency of the input signal.

Memory No. Displays the preset memory number of the input signal.

Signal type Displays the type of the input signal.

Lamp Timer Indicates how long the lamp has been turned on (total usage).

Notes

About the Preset Memory No.

Note

Memory No.

Signal type

Serial No.

Model name: VPL-VW200

55

VPL-VW2003-275-583-13 (1)

D:\WORK\VW60GB\3275583131\3275583131VPLVW200UC\010GB_VPLVW200UC\080COM.fm

masterpage:Left

Accessing the Projector from a Computer

You can check the present status of the projector on a computer display and control the projector from a computer.Confirm that the projector and computer are connected to the router/hub with the LAN cables, then turn on the projector, computer and router/hub.

1 Start Internet Explorer 5.0 (or later version) on your computer.

2 Type “http://xxx.xxx.xxx.xxx (the IP address of the projector)” as the “Address,” then press the ENTER key on a keyboard.You can check the IP address of the projector using the Installation menu. (1 page 54)

TipWhen “Standby Mode” in Setup setting is set to “Standard1”, you can access the projector from a computer even if the projector is in standby mode.

Checking the Status of the Projector

Click “Information.” You can check the information and present status of the projector on a computer display. You can check the information and status in the window, but you cannot change the setting.

InformationThe present status of the projector is displayed.

fH (horizontal frequency) and fV (vertical frequency) may not be displayed appropriately, depending on the equipment connected to the projector.

MenuThe present settings of the projector are displayed.

Operating the Projector from a Computer

Enter the IP address here.

Note

56

VPL-VW2003-275-583-13 (1)


masterpage:Left

Operating the P

rojector from a C

omputer

Operating the Projector

Click “Control.” You can perform various adjustments and settings of the projector on a computer display.The functions of the buttons in the windows are the same as those on the remote control supplied with the projector.

Setting the Information

Click “Setup.” The Password Properties dialog box appears. The name of the “User” account is preset without a password to “root” at the factory. You can set the owner information, etc. Click “Apply” at the lower part of each window to update the projector to the data input in each window.

Owner and projector informationClick “OWNER INFORMATION.”

OwnerEnter owner information.

ProjectorEnter the location of the projector.

MemoEnter a memo, if required.

Network settingsClick “NETWORK.”

Internet Protocol (TCP/IP)Normally, set “Obtain an IP address automatically (DHCP).” If you select “Specify an IP address,” set the necessary items.

Settings of the projector are lit.After you have changed the settings on the projector, click “Refresh” at the upper right-hand corner of the window to update the status. The lighting buttons are changed.

57

VPL-VW2003-275-583-13 (1)


masterpage:Left

Setting passwords for “Administrator” and “User”Click “Password.” You can set passwords for each “Administrator” and “User.” The name of the “Administrator” account is preset to “root” at the factory. It cannot be changed.

Advanced settingClick “ADVANCED MENU” to display the Advertisement button, PJ Talk button, SNMP button and Reset button. These settings are mainly for professional use. Detailed information on Advertisement button and PJ Talk button are indicated by the PROTOCOL manual. For details on each function of “Advanced setting”, consult with your local dealer or qualified Sony personnel.

To reset the settingClick the Reset button displayed in “Advanced setting”. The data set in “Setup” are reset to its factory preset value.

• The data input will be recorded in the memory of the projector.

• These data may become a personal information, depending on the content input. Therefore, it is recommended that you input content that cannot specify particular individuals.

• These data may be sent out through the network by “Advertisement”, “PJTalk” and “SNMP” functions.

• On disposal or transfer of the projector, it is strongly recommended that you delete the data recorded in the memory of the projector. On how to delete the data, see “To reset the setting”.

Notes

58

VPL-VW2003-275-583-13 (1)

D:\WORK\VW60GB\3275583131\3275583131VPLVW200UC\010GB_VPLVW200UC\09OTH.fm

masterpage:Left

Others

This section describes about the other functions, how to solve the problems, how to replace the lamp and air filter, etc.

About the HDMI Control

What is the HDMI Control?HDMI Control is an HDMI standard mutual control function which uses the HDMI CEC (Consumer Electronics Control) specification. By connecting a variety of HDMI control compatible equipment such as a DVD recorder, an AV amplifier, etc., with an HDMI cable, you can operate your equipment synchronizing with the HDMI control compatible equipment connected to the equipment. When using the HDMI Control function, be sure to assign the appropriate connection and settings.

Connecting a HDMI control compatible equipmentConnect the projector with an HDMI control compatible equipment using an HDMI cable. Be sure to use a cable that has acquired the HDMI logo for your connection.

The HDMI Control function is available only between Sony HDMI control compatible equipment.

Setting the HDMI ControlBe sure to assign the appropriate connections for both the projector and the HDMI control compatible equipment connected to the projector. For settings of the projector, see 1 page 50. For settings of the HDMI equipment connected to the projector, refer to its operational instructions.

What you can do with the HDMI Control• System Standby

You can power off the projector and the HDMI control compatible equipment connected to the projector at the same time.

• One Touch PlayWhen the HDMI control compatible equipment connected to the projector is played back, the projector is also automatically powered on, and its input setting is synchronized at the same time.

• To operate the connected equipment, be sure the equipment is HDMI control compatible and assign the appropriate settings to use the HDMI Control function.

• Depending on the connected equipment, the HDMI Control function may not work appropriately. For the settings of the connected equipment, refer to the operating instructions of the equipment.

About the x.v.Color

• x.v.Color is a more familiar term for the xvYCC standard proposed by Sony, and is a trademark of Sony.

• xvYCC is an international standard for color space in video. This standard can express a wider color range than the currently used broadcast standard.

Others

Note

Notes

59

VPL-VW2003-275-583-13 (1)


masterpage:Left

TroubleshootingIf the projector appears to be operating erratically, try to diagnose and correct the problem using the following instructions. If the problem persists, consult with qualified Sony personnel.

Power

Picture

Symptom Cause and Remedy

The power is not turned on. c After about one minute, turn the power on. c Close the lamp cover securely, then tighten the screws securely.

(1 page 67)c Close the filter holder securely. (1 page 69)c Check warning indicators. (1 page 62)


No picture. c Check that the proper connections have been made. (1 page 18)

c Select the input source correctly using the INPUT button. (1 page 28)

c Set the computer signal to output from an external monitor.c Set the computer signal to output only to an external monitor.c Select “Computer,” “Component” or “Video GBR” for “Input-A

Signal Sel.” on the Setup menu according to the input signal. (1 page 49)

The picture from the INPUT A connector is colored strange.

c Select “Computer,” “Component” or “Video GBR” for “Input-A Signal Sel.” on the Setup menu according to the input signal. (1 page 49)

The picture from the VIDEO INPUT or S VIDEO INPUT connector is colored strange.

c Adjust the picture of the Picture menu. (1 page 41)c Set “Color System” in the Setup menu to match the color

system being input. (1 page 49)

The color gradation of the dark area or the bright area of the picture from the HDMI 1 or HDMI 2 connector becomes unclear.

c The color gradation of the dark area or the bright area may become unclear when a signal other than those from HDMI standard is input. Adjust the “Brightness” and the “Contrast” in the Picture menu. (1 page 42)

The picture is too dark. c Adjust the “Contrast” or “Brightness” of the Picture menu properly. (1 page 42)

The picture is not clear. c Adjust the focus. (1 page 25)c Condensation has accumulated on the lens. Leave the projector

for about two hours with the power on.

60

VPL-VW2003-275-583-13 (1)


masterpage:Left

Others

On-screen display

Remote control

Others


The picture flickers. c Activate “APA”, then adjust the current input signal.c Adjust “Phase” for “Adjust Signal” in the Screen menu

properly. (1 page 47)

The color of characters or the picture is not appropriate.

c Select the desired color registration in “Panel Alignment” of Installation menu (1 page 53).


On-screen display does not appear.

c Set “Status” in the Setup menu to “On.” (1 page 48)c Check if the ?/1 (ON/STANDBY) indicator should light in

green.

The model name does not disappear from the screen.

c The display mode of the projector may be set at the time of purchase. Consult with your local dealer or qualified Sony personnel.


The remote control does not work.

c Batteries could be weak. Replace them with new batteries. (1 page 11)

c Insert the batteries with the correct polarities. (1 page 11)c In the Installation menu, set the setting of “IR Receiver” to

“Front & Rear”. (1 page 52)c If there is a fluorescent lamp near the remote control detector, the

projector may work improperly or inadvertently. Change the setting of “IR Receiver” in the Installation menu. (1 page 52)


The fan is noisy. c Check the setting of “Cooling Setting” in the Setup menu. (1 page 48)

c Make sure that the room temperature is not too high.c Check the installation conditions. (1 page 12)

The number of fan rotation increases to maintain the product reliability of the projector’s components in a room, where the temperature is higher than normal. The fan noise becomes slightly louder. The approximate normal temperature is 25°C.

Image is left on the screen. (image retention)

c When High contrast non-moving images are displayed for a long period of time, there may be some image retention on the screen. This is only a temporary condition. Turning off the power for a while will eliminate the retained image.

61

VPL-VW2003-275-583-13 (1)


masterpage:Left

The ON/STANDBY or LAMP/COVER indicator lights up or flashes if there is any trouble with your projector.

When a warning indicator other than the above starts flashing, and the symptom persists even after carrying out the above methods, consult with qualified Sony personnel.

Warning Indicators


LAMP/COVER flashes in red. (A repetition rate of 2 flashes)

c Close the lamp cover securely, then tighten the screws securely. (1 page 67)

c Close the filter holder securely. (1 page 69)

LAMP/COVER flashes in red. (A repetition rate of 3 flashes)

c The lamp has reached the end of its useful lifespan. Replace the lamp. (1 page 65)

c The lamp has reached a high temperature. Wait until the lamp cools, and then turn on the power again.

ON/STANDBY flashes in red. (A repetition rate of 4 flashes)

c The fan is broken. Consult with qualified Sony personnel.


c The internal temperature is unusually high. Check to ensure that if nothing is blocking the ventilation holes or whether or not the projector is being used at high altitudes.


c Press the I/1 (ON/STANDBY) switch to turn on the projector. If the power is not turned on, disconnect the AC power cord, then confirm the ON/STANDBY lamp is turned off. After about 10 seconds, reconnect the AC power cord and turn on the power again. If the indicators still light up, the electrical system has a problem. Consult with qualified Sony personnel.

Note

ON/STANDBY indicatorLAMP/COVER indicator

62

VPL-VW2003-275-583-13 (1)


masterpage:Left

Others

Warning messages

Message Lists

Message Cause and Remedy

High temp.! Lamp off in 1 min.

c Turn off the power.c Check to ensure that nothing is blocking the ventilation holes.

(1 page 13)

Frequency is out of range! c Frequency is out of range. Input a signal that is within the acceptable frequency range of the projector.

Please check Input-A Signal Sel.

c Set “Input-A Signal Sel.” in the Setup menu to “Computer” when an RGB signal is input from a computer. (1 page 49)

Please replace the Lamp/Filter.Lamp/Filter life remains less than 50H.

c The remaining available usage time for the lamp and the air filter is short. (Estimated approximately 50 hours.)

To clear the message on the screen, press any key on the remote control or the control panel of the projector once.

Please replace the Lamp/Filter.Lamp/Filter life remains less than 15H.

c The remaining available usage time for the lamp and the air filter is short. (Estimated approximately 15 hours.)


Please replace the Lamp/Filter.End of Lamp/Filter life.Lamp off in 1 min.

c It is time to replace the lamp. Replace the lamp. (1 page 65)c Also, replace the air filter too. (1 page 65)

If the message appears again after you replace the lamp and the air filter, the lamp replacement process is not complete. Check the lamp replacement process. (1 page 65)

Please clean the filter. c It is time to clean the air filter. Clean the air filter. (1 page 70)


Please clean the filter. Have you finished? Yes No

c It is time to clean the air filter. Clean the air filter. (1 page 70)c If you cleaned the air filter, select “Yes.” If you did not clean the

air filter, select “No.”

Projector temperature is high. Cooling Setting should be “High” if projector is being used at high altitude.

c Check to ensure that the Ventilation holes on the unit are not covered. (1 page 13)

c When using the projector at high altitude, set the Cooling Setting to “High”. (1 page 48)

When temperature inside the projector remains high, the Cooling Setting is switched to “High” in one minute, then the fan speed increases.

Note

Note

Note

Note

63

VPL-VW2003-275-583-13 (1)


masterpage:Left

Caution messages

Message Cause and Remedy

c No signal is input in the selected input. Check connections. (1 page 18)

Not applicable! c Press the appropriate button.c The operation to be activated by the button is currently

prohibited.

x

64

VPL-VW2003-275-583-13 (1)


masterpage:Left

Others

Replacing the Lamp and the Air Filter and cleaning the Ventilation holes (intake)

Tools you need to get started:Standard Phillips screwdriverCloth (for scratch protection)The lamp used for the light source has a certain lifespan. When the lamp dims, the color balance of the picture becomes strange, or “Please replace the Lamp/Filter. End of Lamp/Filter life. Lamp off in 1 min.” appears on the screen, the lamp may be exhausted. Replace the lamp with a new one (not supplied) without delay.Use an LMP-H400 Projector Lamp as the replacement lamp.The air filter is supplied with the LMP-H400 Projector Lamp. When you replace the lamp, it is also time to replace the air filter.Whenever you replace the lamp, be sure to replace the air filter with a new one. Also clean the ventilation holes (intake).

• The lamp remains hot after the projector is turned off with the ?/1 (ON/STANDBY) switch. If you touch the lamp, you may burn your fingers. When you replace the lamp, w

Documents

Operating Instructionsstatic1.projectorpoint.co.uk/.../sony/vpl-vw200/sony_vpl-vw200-manual.… · Operating Instructions VPL-VW200 3-275-583-13 (1)D:\WORK\VW60GB\3275583131\3275583131VPLVW200UC\00COV_