248

KEY FEATURES AND BENEFITS

Digital and analog video/audio router

› No format limitations

› Mix-and-match: HD, SD, ASI, analog video, analog audio, AES, Time Code, sample rate conversion (SRC) and machine control

› Dolby E certified

› Analog to digital, digital to analog conversion

Versatile design

› 128 x 128 maximum matrix size

› 8RU frame configurable in blocks of 16 inputs or outputs at a time

› Supports non-square configurations

Ultra-resilient design

› Front loading, hot swappable power supplies, input, output and controller modules

› Speed controlled fans

› SNMP support

Highly flexible automated/manual control

› Wide range of remote control panels: traditional hardware and GUI-based

› Enhanced control when router used with NVISION 9000 control system

› Supports many third-party control system protocols

› Simultaneous router control by external automation, facility control systems, and NVISION control systems

› Operational consistency across NVISION product line

DESCRIPTION

The NVISION 5128 is a mid-size, multiformat router, which supports rectangular and squared configurations up to 128 x 128 (in blocks of 16). This highly robust router offers easy “mixing-and-matching” of up to eight different formats in the same frame, including HD, SD, ASI and analog video, as well as digital and analog audio. It can also be used for Time Code, sample rate conversion, and machine control signals.

MIX-AND-MATCH FORMATS

MIX-AND-MATCH FORMATSThe NVISION 5128 mid-sized, multiformat router provides the flexibility to easily adapt to evolving signal routing requirements. This innovative 128 x 128 router supports all current digital and analog formats, namely HD, SD, analog video, analog audio, AES, Time Code, SRC and data. Up to eight different formats can be supported in the same frame, with easy “mixing-and-matching” of signal types. The router provides on-board analog to digital, and digital to analog, conversion for both video and audio signals.

“PLUG AND PLAY” CONFIGURATIONConfiguring the NVISION 5128 is as simple as plugging modules into the front of the frame, and installing I/O assemblies in the rear. Reconfiguring the system is equally straightforward. No motherboard changes or internal rewiring are required, so you don’t have to worry about taking the router out of service to reconfigure it.

UNIQUE FAULT-TOLERANT DESIGNThe router is designed for reliability, fault tolerance and redundancy. All input and output modules, power supplies, controllers, and fans are front accessible and hot swappable. No rear cables need to be removed for servicing or maintenance, and power supplies are fully redundant with continuous load sharing between supplies.

FLEXIBLE REMOTE CONTROLField proven in hundreds of installations worldwide with millions of hours of continuous operation, the NVISION router control systems are ideal for mission critical applications. Designed to grow with your needs, the router control system offers a full complement of user interface options, along with full redundancy, and an easy-to-use Java based configuration editor.

The remote control panels include highly configurable hardware and virtual control panels. They provide all the features, functions and redundancy essential to address a broad range of applications, from the smallest television station to the largest uplink and origination centers.

MODEL

NVISION 5128 NVISION 5128 MID-SIZE, MULTIFORMAT ROUTER

128 X 128 STEREO AUDIO

64 X 64 STEREO AUDIO

80 X 96 STEREO AUDIO

64 X 64 STEREO AUDIO

32 X 32

The NVISION 5128 allows “mixing-and-matching” of any format, using rectangular or square matrices.

www.amt.com

249

NVIS

ION

ROUT

ING

SYST

EMS

TECHNICAL SPECIFICATIONS

ELECTRICALAC input: 90-130/180-250 VAC, 50/60 Hz,

auto-rangingAC fuses: Power supplies: 8A

(HB0145-00), slow blow; 90-130 V, 6.3A (HB0031-00), slow blow, 180-250 V

AC connectors: 2, IEC 320AC power: PS6000, 660 W, one IEC 320AC power usage: Power based on PS6000 modules 425 W nominal (128 x 128 SD),

power factor corrected 550 W nominal (128 x 128 SWB),

power factor corrected 260 W nominal (128 x 128 analog

video), power factor corrected 500 W nominal (128 x 128 AVC),

power factor corrected 225 W nominal (128 x 128 sync

AES), power factor corrected 625 W nominal (128 x 128 analog

audio), power factor corrected Note: Power consumption

dependent on number of cards installed

Regulatory compliance: UL listed and CE compliant

MECHNICALDimensions: 14 in (355.6 mm) 8RU high 19 in (483 mm) wide 18 in (457 mm) deepWeight: 56 lb (25.5 kg); 182 lb (82.7 kg)

fully loadedMounting: EIA 310-C, 19 in (483 mm)Grounding terminal: Copper, accepts 14-6 AWGModules and slots: 8 input cards, 16 signals each 8 crosspoint/output cards,

16 signals each 2 control cards (1 primary,

1 optional secondary) 1 fan module 2 PS6000 modules

(1 required, 1 optional redundant)

DIAGNOSTICType: Serial portConnector: SMPTE 207M, EIA-422/EIA-232,

configurableStandard: 2, DE-9

SERIAL CONTROLType: Serial port (2 per control card)Standard: SMPTE 207M, EIA-422,

configurableConnector: 4, DE-9

ETHERNETType: 10/100 Base TStandard: IEEE 802.3Protocol: NVISION Ethernet protocolConnector: 2, RJ45

GSC NODE BUSType: SerialStandard: ProprietaryConnector: 2, BNC, loop through,

non-terminating pairImpedance: 75 ohm

POWER SUPPLY ALARMConnector: Phoenix

ENVIRONMENTAL SPECIFICATIONSOperating temperature: 0 to 40 °CRelative humidity: 0 to 90 %, non-condensing

AUDIO REFERENCE INPUTType: Serial digital audioStandard: AES3 or AES3idSample rate: 48 kHz Connector: 2, BNC or PhoenixImpedance : 75 ohm or 110 ohmLevel: 0.5 Vp-p to 2.0 Vp-p

INPUTS/OUTPUTSType: Balanced digital audioStandard: AES3Sample rate: Synchronous 48 kHz Asynchronous 32 to 96 kHzConnector: PhoenixImpedance: 110 ohmInput level: 200 mV to 10 Vp-pOutput level: 2 Vp-p

AES3ID INPUTS/OUTPUTSType: Unbalanced digital audioStandard: AES3idSample rate: Synchronous 48 kHz Asynchronous 32 to 96 kHzConnector: BNCImpedance: 75 ohmInput level: 100 mV to 1.2 Vp-p Output level: 1 V ±10 %

ANALOG AUDIO INPUTS/OUTPUTSType: Analog audioStandard: 24-bit at 48 kHzSample rate: 48 kHzConnector: DB-25Impedance: Input > 20 kohm , output 50 ohmInput level: FSD, +15, +18 and +24 dBuOutput level: FSD, +15, +18 and +24 dBu,

selectable +6 dB gain via switchFreq. response: 20 Hz to 20 kHz B10.2 dBTHD: <0.02 % at +4 dBu at 1 kHzIMD: <0.5 % (per SMPTE method

using a 60 Hz +12 dBu wave and a 7 kHz 0 dBu sine wave) sine

Noise: 95 dB below +24 dBuInter-route delay: <1 µsInput to output delay: <1.2 msCrosstalk: -80 dB worst caseInsertion gain: ±0.1 dBCMRR: >75 dB from 60 Hz to 20 kHz

VIDEO REFERENCE INPUTType: Analog video referenceStandard: PAL, NTSC, or tri-level syncConnector: Loop through, BNCImpedance: 75 ohm or Hi-ZLevel: 0.5 Vp-p to 2.0 Vp-pReturn loss: ≥30 dB to 5 MHz

SD INPUTS/OUTPUTSType: SD serial digital videoStandard: SMPTE 259M and 344MData rates: Auto reclocking at 143, 177, or

270 Mbps or auto bypass Pass-through at 10 Mbps to

270 Mbps Note: Inputs do not reclockConnector: BNC Impedance: 75 ohm Cable equalization: 300 m Belden 1694A, or

equivalent cable, at 270 MbpsRouter path: Non-inverting

INPUT/OUTPUTReturn loss: >15 dB, 5 to 270 MHzOutput level: ≤800 mVp-p ±10 %Output rise/fall time: ≤600 ps +10 %Output overshoot: ≤10 % of amplitude maxOutput alignment jitter: ≤0.2 UIpp from 1.0 kHz to 27 MHzOutput timing jitter: ≤0.2 UIpp from 10 Hz to 1.0 kHz

SWB (SD AND HD) INPUTS/OUTPUTS Type: HD serial digital videoData rate: SMPTE 259M, 344M and 292M Auto reclocking at 143, 177, 270,

360, 540 Mbps and 1.483 and 1.485 Gbps or auto bypass

Data rate: Pass-through at 10 Mbps to 1.5 Gbps

Note: Inputs do not reclockConnector: BNCImpedance: 75 ohm Equalization: 150 m Belden 1694A, 85 m

Belden 1855A, or equivalent cable, at 1.5 Gbps

Router path: Non-invertingOutput level: 800 mVp-p ±10 %I/O return loss: >15 dB, 5 MHz to 1.5 GHzOutput rise/fall time: ≤270 psOutput overshoot: ≤10 % of amplitude maxOutput alignment jitter: �≤0.2 UIpp from 100 kHz to

150 MHzOutput timing jitter: ≤1.0 UIpp from 10 Hz to 100 kHz

ANALOG VIDEO INPUTS/OUTPUTS Type: Analog videoStandard: NTSC, PALConnector: BNCImpedance: 75 ohmInput return loss: >45 dB to 6 MHzOutput return loss: >45 dB to 6 MHzOutput level: 1 Vp-pOutput DC offset: 1 Vp-p, nominalInput range: ±30 mV relative to backporchInsertion loss: ±2 V 0 dB B10.1 dB all inputs to

any one outputFreq. response: ±0.1 dB to 8 MHzDifferential gain: <0.1 dB

Differential phase: <0.1°Tilt: <0.2 %Delay scatter: ±1.75° any input to any output ±1.5° any input to any output

slot (16 outputs) ±1.0 any input to any single

outputNoise spectrum: >80 dB with pedestal

unweighted to 7 MHzCMRR: >60 dB to 10 kHzCrosstalk: 57 dBrms worst case (100 % PAL

color bars), 72 dBrms worst case (single to adjacent crosstalk)

Output to output isolation: >40 dB

ANALOG/DIGITAL VIDEO CONVERSIONType: Analog digital videoStandard: NTSC, PAL analog composite

videoConnector: BNCImpedance: 75 ohmLevel: 1 Vp-p, nominalCommon mode range: ±2 Vp-pFreq.response (input): ±0.5 dB to 5.5 MHz (luminance)Freq. response (output): ±0.2 dB to 5.5 MHz (luminance)Luma/chroma delay: <12 nsLuma/chroma gain inequality: <0.5 dBDifferential gain: <0.3 %Differential phase: <0.3°Pedestal (input): >75 dB unweightedPedestal (output): >75 dB unweightedRamp (input): >50 dB unweightedRamp (output): >62.5 dB unweighted

TIME CODE REFERENCE INPUTType: 1 BNC, 1 PhoenixStandard: SMPTE 12M Connector: BNC terminating, PhoenixImpedance: 75 ohm or 110 ohm

TIME CODE INPUTS/OUTPUTSType: Longitudinal Time CodeStandard: SMPTE 12M Connector: PhoenixImpedance: 600 ohm or Hi-Z, selectableInput level: 100 mV to 10 Vp-pOutput level: 2.0 Vp-p

PORT MACHINE INPUTS/OUTPUTSType: Bi-directional, dynamically

configuredStandard: EIA232 or EIA-422,

ANSI/SMPTE 207MConnector: RJ45Data rates: Up to 115.2 kbps

NVIS

ION

ROUT

ING

SYST

EMS

NVISION 5128Mix-and-match signals in one frame

ORDERING INFORMATION

FrameFR5128 128X128 frame with power supply and manual CONTROL5128-NV NV5128 control card with NVISION protocol

VIDEO (FRONT MODULES)NV5000-SD-IN 16 IN SDI digital video moduleNV5000-SD-OUT 16 OUT SDI digital video moduleNV5000-AV-IN 16 IN analog video moduleNV5000-AV-OUT 16 OUT analog video moduleNV5000-AVC-IN 16 IN analog video conversion moduleNV5000-AVC-OUT 16 OUT analog video conversion moduleNote: Classic NV5128 HD routing modules allow for configurations of up to 32x32. Contact factory for

additional details.NV5000-HD 16X16 I/O HD-SDI moduleNote: New NV5128 HD routing modules allow for configurations of up to 128x128. Contact factory for

additional details.NV5000-HD-IN 16 IN HD-SDI video moduleNV5000-HD-XPT-OUT 16 OUT HD-SDI digital video module with crosspointsNote: One NV5000-HD-XPT-OUT is required for each group of 64 HD outputs.

VIDEO (REAR MODULES)IO5000-SD-IN Rear connector module for NV5000-SD-INIO5000-SD-OUT Rear connector module for NV5000-SD-OUTIO5000-AV-IN Rear connector module for NV5000-AV-INIO5000-AV-OUT Rear connector module for NV5000-AV-OUTIO5000-AVC-IN Rear connector module for NV5000-AV-INIO5000-AVC-OUT Rear connector module for NV5000-AV-OUT

AUDIO (FRONT MODULES)NV5000-SA-IN 16 IN AES synchronous moduleNV5000-SRC-IN 16 IN sample rate converted (SRC) moduleNV5000-SA-OUT 16 OUT AES synchronous moduleNV5000-A-IN 16 IN AES asynchronous moduleNV5000-A-OUT 16 OUT AES asynchronous moduleNV5000-AA-IN 16 IN analog audio moduleNV5000-AA-OUT 16 OUT analog audio module

AUDIO (REAR MODULES)IO5000-AES-IN-BNC Rear IN connector module for AES-BNCIO5000-AES-IN-TP Rear IN connector module for AES-twisted pairIO5000-AES-OUT-BNC Rear OUT connector module for AES-BNCIO5000-AES-OUT-TP Rear OUT connector module for AES-twisted pairIO5000-AES-IN-BNC Rear IN connector module for AES-BNCIO5000-AES-IN-TP Rear IN connector module for AES-twisted pairIO5000-AES-OUT-BNC Rear OUT connector module for AES-BNCIO5000-AES-OUT-TP Rear OUT connector module for AES-twisted pairIO5000-AA-IN Rear connector module for NV5000-AA-INIO5000-AA-OUT Rear connector module for NV5000-AA-OUT

TIME CODE (FRONT MODULES)NV5000-TC-IN 16 IN Time Code moduleNV5000-TC-OUT 16 OUT Time Code module

TIME CODE (REAR MODULES)IO5000-TC-IN-BNC Rear IN connector module for Time Code - BNCIO5000-TC-IN-TP Rear IN connector module for Time Code - twisted pairIO5000-TC-OUT-BNC Rear OUT connector module for Time Code - BNCIO5000-TC-OUT-TP Rear OUT connector module for Time Code - twisted pair

DATA (FRONT MODULES)NV5000-RS422-DATA 32 port RS-422 data module (occupies 2 slots)NV5000-RS232-DATA 32 port RS-232 data module (occupies 2 slots)

DATA (REAR MODULES)105000-DATA 16 port data rear RJ45 module

OTHER OPTIONSNV5000-CABLE1 15 foot AA breakout cable. D connector to pigtail. Four stereo pairs5128-FAN 1 NV5128 fan tray with speed control -sparePS6100 6000 Series Redundant PS