Installing Flexi Multiradio 10 BTS for Stack, Wall, And Pole Configurations

  • View
    226

  • Download
    1

Embed Size (px)

Text of Installing Flexi Multiradio 10 BTS for Stack, Wall, And Pole Configurations

  • 7/22/2019 Installing Flexi Multiradio 10 BTS for Stack, Wall, And Pole Configurations

    1/19

    18 DN09107819

    Installing Flexi Multiradio 10 BTS for Stack, Wall, andPole Configurations

    Id:0900d80580988089

    Confidential

    Installing Flexi Multiradio 10 BTS optional sub-modules

    6 Installing Flexi Multiradio 10 BTS optional

    sub-modules

    6.1 Installing Flexi Multiradio 10 BTS Power Distribution Sub-Module (FPFD)

    Before you start

    If cable entries are installed, remove them.

    Steps

    Remove the FPFD dummy unit as follows:

    Undo the screws holding the FSMx core in place.

    Pull out the core.

    Remove the three screws holding the FPFD dummy unit in place.

    g Leave the other dummy units in place if you are not installing any other optional sub-modules.

  • 7/22/2019 Installing Flexi Multiradio 10 BTS for Stack, Wall, And Pole Configurations

    2/19

    DN09107819 19

    Installing Flexi Multiradio 10 BTS for Stack, Wall, andPole Configurations

    Installing Flexi Multiradio 10 BTS optional sub-modules

    Id:0900d80580988089

    Confidential

    Figure 7 Removing dummy unit

    b

    c

  • 7/22/2019 Installing Flexi Multiradio 10 BTS for Stack, Wall, And Pole Configurations

    3/19

    20 DN09107819

    Installing Flexi Multiradio 10 BTS for Stack, Wall, andPole Configurations

    Id:0900d80580988089

    Confidential

    Installing Flexi Multiradio 10 BTS optional sub-modules

    Remove the rubber plugs on the core and the FPFD.

    Figure 8 Removing rubber plugs

    Insert the connection card to the slot on the FSMx core.

    g The connection card for the FPFD looks identical with the transmission sub-module con-nection card. Make sure you are inserting the correct card.

  • 7/22/2019 Installing Flexi Multiradio 10 BTS for Stack, Wall, And Pole Configurations

    4/19

    DN09107819 21

    Installing Flexi Multiradio 10 BTS for Stack, Wall, andPole Configurations

    Installing Flexi Multiradio 10 BTS optional sub-modules

    Id:0900d80580988089

    Confidential

    Figure 9 Inserting connection card

  • 7/22/2019 Installing Flexi Multiradio 10 BTS for Stack, Wall, And Pole Configurations

    5/19

    22 DN09107819

    Installing Flexi Multiradio 10 BTS for Stack, Wall, andPole Configurations

    Id:0900d80580988089

    Confidential

    Installing Flexi Multiradio 10 BTS optional sub-modules

    Remove the DC screw terminal cover from the FPFD sub-module.

    Figure 10 Removing DC screw terminal cover

    Loosen the screw terminals with an Allen key.

    Figure 11 Loosening screw terminals

  • 7/22/2019 Installing Flexi Multiradio 10 BTS for Stack, Wall, And Pole Configurations

    6/19

    DN09107819 23

    Installing Flexi Multiradio 10 BTS for Stack, Wall, andPole Configurations

    Installing Flexi Multiradio 10 BTS optional sub-modules

    Id:0900d80580988089

    Confidential

    Remove the IP plugs from the cable glands.

    Figure 12 Removing IP plugs

    Remove cable glands heads.

    Figure 13 Removing cable glands heads

    Strip the DC input cable for 16 mm.

    The cable size range for the DC input cable is 6 to 25 mm2and the outer cable diameter

    4 to 11 mm.

    g If your DC input cable is coming from Flexi Power Module (FPMA) (cable code 995069),the pre-cut guide mark for cable stripping is at 11 mm. Make a new cut at 16 mm and

    then strip the cable.

  • 7/22/2019 Installing Flexi Multiradio 10 BTS for Stack, Wall, And Pole Configurations

    7/19

    24 DN09107819

    Installing Flexi Multiradio 10 BTS for Stack, Wall, andPole Configurations

    Id:0900d80580988089

    Confidential

    Installing Flexi Multiradio 10 BTS optional sub-modules

    If the cable diameter is greater than 6 mm, remove the inner rings from the cable

    glands.

    Figure 14 Removing inner rings from cable glands

    Thread your DC input cable through the cable glands.

    Use lubricant if necessary.

    Figure 15 Threading DC input cable through cable glands

    Replace the inner cable gland with the DC input cable routed through it.

    Figure 16 Replacing inner cable gland

  • 7/22/2019 Installing Flexi Multiradio 10 BTS for Stack, Wall, And Pole Configurations

    8/19

    DN09107819 25

    Installing Flexi Multiradio 10 BTS for Stack, Wall, andPole Configurations

    Installing Flexi Multiradio 10 BTS optional sub-modules

    Id:0900d80580988089

    Confidential

    Insert the DC input cable to the inner screw terminal and tighten it to 4 Nm with an

    Allen key.

    w NOTICE:The edge of the cable insulation should be visible before tightening the screwterminal.

    Figure 17 Tightening inner screw terminal

    Tighten the inner cable gland.

    Figure 18 Tightening inner cable gland

  • 7/22/2019 Installing Flexi Multiradio 10 BTS for Stack, Wall, And Pole Configurations

    9/19

    26 DN09107819

    Installing Flexi Multiradio 10 BTS for Stack, Wall, andPole Configurations

    Id:0900d80580988089

    Confidential

    Installing Flexi Multiradio 10 BTS optional sub-modules

    Replace the outer cable gland with the DC input cable routed through it.

    Figure 19 Replacing outer cable gland

    Insert the DC input cable to the outer screw terminal and tighten it to 4 Nm with

    an Allen key.

    w NOTICE:The edge of the cable insulation should be visible before tightening the screwterminal.

    Figure 20 Tightening outer screw terminal

  • 7/22/2019 Installing Flexi Multiradio 10 BTS for Stack, Wall, And Pole Configurations

    10/19

    DN09107819 27

    Installing Flexi Multiradio 10 BTS for Stack, Wall, andPole Configurations

    Installing Flexi Multiradio 10 BTS optional sub-modules

    Id:0900d80580988089

    Confidential

    Tighten the outer cable gland.

    Figure 21 Tightening outer cable gland

    Check with multi-meter the resistance between +/- terminal screw and chassis.

    The resistance should be Ms.

  • 7/22/2019 Installing Flexi Multiradio 10 BTS for Stack, Wall, And Pole Configurations

    11/19

    28 DN09107819

    Installing Flexi Multiradio 10 BTS for Stack, Wall, andPole Configurations

    Id:0900d80580988089

    Confidential

    Installing Flexi Multiradio 10 BTS optional sub-modules

    Replace the DC screw terminal cover and tighten the screws for 2 Nm.

    Figure 22 Replacing DC screw terminal cover

  • 7/22/2019 Installing Flexi Multiradio 10 BTS for Stack, Wall, And Pole Configurations

    12/19

    DN09107819 29

    Installing Flexi Multiradio 10 BTS for Stack, Wall, andPole Configurations

    Installing Flexi Multiradio 10 BTS optional sub-modules

    Id:0900d80580988089

    Confidential

    Align the FPFD with the guide pin on the FSMx core, and push the FPFD in place.

    Figure 23 Installing FPFD

  • 7/22/2019 Installing Flexi Multiradio 10 BTS for Stack, Wall, And Pole Configurations

    13/19

    30 DN09107819

    Installing Flexi Multiradio 10 BTS for Stack, Wall, andPole Configurations

    Id:0900d80580988089

    Confidential

    Installing Flexi Multiradio 10 BTS optional sub-modules

    Fix the FPFD with 3 x M5x25 screws (included in the accessory bag) and tighten

    to 4.0 Nm.

    Figure 24 Fixing FPFD

    Route the DC input cable.

    Route the DC input cable, as shown in Figure 25 Routing DC input cable between FPFD

    and transmission sub-module.

    g If transmission sub-module is not used, the DC input cable can be routed between FPFDand dummy unit.

  • 7/22/2019 Installing Flexi Multiradio 10 BTS for Stack, Wall, And Pole Configurations

    14/19

    DN09107819 31

    Installing Flexi Multiradio 10 BTS for Stack, Wall, andPole Configurations

    Installing Flexi Multiradio 10 BTS optional sub-modules

    Id:0900d80580988089

    Confidential

    Figure 25 Routing DC input cable between FPFD and transmission sub-module

    Re-insert the module core and fix the screws.

  • 7/22/2019 Installing Flexi Multiradio 10 BTS for Stack, Wall, And Pole Configurations

    15/19

    32 DN09107819

    Installing Flexi Multiradio 10 BTS for Stack, Wall, andPole Configurations

    Id:0900d8058098adf6

    Confidential

    6.2 Installing Flexi Multiradio 10 BTS optional Transmission

    Sub-Module (FTIF)

    Purpose

    Flexi Multiradio System Module core (FSMF/G) has an integrated Gigabit Ethernet andoptical Ethernet transport interface available on the front panel, however, if more or

    other Ethernet interfaces are required then install an optional transmission sub-module

    (FTIF). The sub-module is also mandatory in co-location cases when a backhaul con-

    nection or synchronization is done through time-division multiplexing (TDM).

    Before you start

    The System Module has to be powered off before installing or replacing the transmission

    sub-module.

    If cable entries are installed, remove them.

    Steps

    Remove the FTIF dummy unit as follows:

    Undo the screws holding the FSMx core in place.

    Pull out the core.

    Remove the four screws holding the FTIF dummy unit in place.

    g Leave the other dummy units in place if you are not installing any other optional sub-modules.

  • 7/22/2019 Installing Flexi Multiradio 10 BTS for Stack, Wall, And Pole Configurations

    16/19

    DN09107819 33

    Installing Flexi Multiradio 10 BTS for Stack, Wall, andPole Configurations

    Id:0900d8058098adf6

    Confidential

    Figure 26 Removing dummy unit

  • 7/22/2019 Installing Flexi Multiradio 10 BTS for Stack, Wall, And Pole Con

Search related